Search Results

Search found 11828 results on 474 pages for 'nokia pc suite'.

Page 101/474 | < Previous Page | 97 98 99 100 101 102 103 104 105 106 107 108  | Next Page >

• How to Enable old networking protocols in Windows 7

  - by Will

  Hi, A few days ago I installed Win7 32bit on a PC and it wouldn't talk to my Lacie NAS which is running WinXP embedded. My other Win7 PC's had no problem. After a bit of searching I found a forum post that told me to enable older networking protocols on the Win7 PC, I think it was win98 protocols or something like that. I had to run a .msc program to do this. It fixed the problem. Now, I have a similar problem on another Win7 PC and for the life of me cannot find that posting and cannot remember what I did! Does anyone know the program or setting to do this? Thanks, Will.

  Read the article

• How can I fix my vista PCs screen resolution and refresh rate

  - by Antony Scott

  I have a media PC running media portal hooked up to my HDTV via HDMI. The TV is a couple of years old now, so only supports 1080i, which is 1920x1080@25Hz. I've got it connected to my PC via a HDMI compatible AV receiver. If I power up the amp (wait for it to boot fully) followed by the TV| and finally the PC, all is well and I get a picture. If I deviate from that sequence, or don't wait for the amp to book up fully, or even switch the amp to another video input (for example, my PS3). The PC sees this and defaults the screen resolution/refresh rate to 1920x1080@60Hz. So, I end up with a blank screen. To fix this I have to use UltraVNC from a PC and change the refresh rate back to 25Hz. So, is there a way to turn off that auto detection, or to manually define what resolution/refresh rates the monitor can do. I'm using the on-board Radeon 3200 video and do not have any of the AMD software installed as it seems to cause problems with video playback. So, I'm looking for a native vista fix, or possible some 3rd party software.

  Read the article

• Help me a routing server on Windows XP

  - by Lu Lu

  I am developing client/server applications and need to test them on Internet environment. However, I only have one PC without connecting the public internet, so I have a plan to simulate a virtual internet environment on my PC. I think I will install the virtual machines for my purpose, but I can install only one machine because of my slowly PC. At the moment, my PC has 2 machines: the host machine (use Windows XP) & the virtual machine (use Windows Server 2003 Ent). Each machine will have 2 network adapter (host-only & internal), and in 2 network adapters, the internal adapter is private on each machine, and host-only adapters are connected together. With Windows 2003, routing server is ok, but I wonder on Windows XP, are there any routing server product? Please help me. Thanks.

  Read the article

• How can I join two simple home networks together using an ethernet cable?

  - by Ilia Jerebtsov

  I want to join two different home networks together like so: PC A1 PC A2 PC B1 PC B2 \ / \ / Gateway A <----- ethr. cable -----> Gateway B | | ADSL modem A ADSL modem B Both networks are of the basic residential type with identical configuration, with all PCs running Vista/7. The point is to temporarily join two apartments in a building for gaming and file sharing, and the holy grail would be: PCs on network A can access PCs on network B and vice-versa (file shares and gaming). Each network uses its own internet connection. Data between networks shouldn't take a trip through the internet (broadband upload speeds are severely capped) A network's internet access should continue working if the joining cable is disconnected with minimal configuration changes. How closely can this be achieved?

  Read the article

• Win7 + SysPrep + CloneZilla = lost settings

  - by oshirowanen

  I've just cloned a PC (Win7 + SysPrep + CloneZilla) and after starting up the new clone, Win7 wants to be reactivated again and the video driver seems to be missing (as in the aero effect has disappeared from the new clone) and the internet connection settings seem to be missing too. All those were set in the master before running SysPrep. Why have these settings been lost? The master PC was had windows 7 activated using a volume license key, and the clone pc is the same make and model as the master computer.

  Read the article

• Which free VNC server works well with Windows 7 and how to advertise it via Bonjour for control by a

  - by GJ

  Hi I need to control a Windows 7 PC via VNC from a Mac in an office LAN. Since the IPs are dynamically assigned, I'd like the PC to appear in my "Places" and in the automatically detected nearby servers in VNC client I'm using -- both of which require the PC to advertise its VNC server via Bonjour (right?). I tried installing ultravnc, which works when I access it directly by IP, but it doesn't seem to advertise itself in the network. Any ideas?

  Read the article

• Ubuntu not installed-Please Remove installation media and close tray and press enter

  - by Ram

  I have downloaded Ubuntu 12.04.1 LTS 32 bit, burned it on DVD and tried to install it on my PC. My PC is running in Windows 7 Ultimate 32 bit mounted on the C: drive. Now I want install Ubuntu along with my Windows 7. When I boot Ubuntu through the CD, It boots and the Ubuntu install windows opens It offers "Try Ubuntu" and "Install Ubuntu". I choose "Install Ubuntu" Then I go on to install Ubuntu with Windows(First Option)-install It shows some blank screen with some lines, and says "Please Remove installation media and close tray and press enter" Then the PC restarts and runs Windows 7 same as before normally. But Ubuntu is not installed. How to solve this problem and install Ubuntu on my PC properly? Note: I am an Android Developer. So I need to install Ubuntu for my Android Development purpose.

  Read the article

• Connecting to a remote mysql server from a windows machine (XP)

  - by Samuel Martin

  I am trying to connect to mysql server which is installed on my home pc from another pc. I allowed all connection in mysql configuration. There's no firewall blocking on the pc I am trying to connect from. I used the command- mysql -h Some.Host.IP -u SomeUser -p SomePassword I am getting- ERROR 2003 (HY000): Can't connect to MySQL server on 'Some.Host.IP' (10060) I can connect through php!! What's the problem? How do I solve it?

  Read the article

• Why is my CPU fan so loud?

  - by tiiquu

  I bought an old PC to use as a second PC. Everything is fine, except for one thing. The CPU fan is terribly loud! I did a lot with PCs but I never did much with CPU fans. If I want to replace it, what do I have to look for? The fan is 8cm long on each side and 11cm diameter. It is just clipped to the cooler. The PC is a P4 3 GHz. I don't want to spend much money, as I only paid 50 euro for the whole PC. I would prefer to buy a fan for 1-3 dollar or something at eBay but I am not quite sure which one I should buy (which fits). Can you advise?

  Read the article

• Is it possible to provide a wired ethernet connection to external devices with an extra LAN card?

  - by Ben McCormack

  I'm trying to provide a wired ethernet connection (wireless is not an option for this device) to a device (Samsung blu-ray player) without running Cat5 cable all over the home. I have a PC sitting next to this device and the PC is connected to the network via a wireless USB adapter. Is it possible to provide a wired connection from the PC to the wired device using the (currently unused) ethernet port in the back of the computer? Here's how I envision the device getting connected to the internet via my network: Linksys WRT54G v8 Wireless Router | ``--> Windows 7 PC connected via wireless | ``--> Blu-ray player connected via wired connection to the ethernet port on the PC. If so, how is this done? Will I need a crossover cable? What settings will I need to change in Windows 7 so that the device can connect? NOTE: I'm trying to avoid having to buy a wireless bridge and/or hacking a router with an open-source firmware to get this to work. See my previous question for more details.

  Read the article

• Can two users both control a third machine simultaneously using Synergy?

  - by Reason

  I've been a Synergy user for some time now, as I use a PC on the left side of my Mac. My girlfriend and I both have our desks on each side of the other, and we'd like to know if it were possible for the both of us to control the PC in the middle, with our own separate mouse & keyboards. Here's a crude drawing of our setup (1) her pc (2) my pc (3) my mac Currently, 3 is running a synergy server, and 2 is running the client. But like I said, I'm wondering if there's a way for 1 & 3 to both control 2 with their own mouse and keyboard. I'd ~love~ to have it set up where we could go even farther, and have both of our mice & keyboards able to control all 3 computers at the same time, for moments when we need to click or press keys for each other. But that seems a little too much to ask! Any thoughts?

  Read the article

• Windows 8 with LiveID login authenticates as Guest to remote SQl Server

  - by Tim Long

  I have a network where several users are using Office Accounting 2009 in multi-user client/server mode. OA is built on SQL Server. One PC acts as the 'server' and has the SQl Server instance, the others have only the application installed and no SQL instance, all of the apps connect remotely to the SQL instance on the 'server'. I'm using the term 'server' loosely here, it is just a normal workstation that happens to be designated as the server and runs the SQL instance. There is no NT domain, all user accounts are local accounts. The way that OA works in multi-user mode is that each user is required to have a local account with the same username and password on both the client and 'server' PCs. This has been working well, no along comes Windows 8. I use my 'Microsoft Account' aka LiveID to log into Windows 8. Office Accounting runs fine and attempts to connect to the database, but fails, 'you do not have permission to perform this operation'. In the SQL logs, I get this error: 2012-10-28 17:54:01.32 Logon Error: 18456, Severity: 14, State: 11. 2012-10-28 17:54:01.32 Logon Login failed for user 'SERVER\Guest'. Reason: Token-based server access validation failed with an infrastructure SERVER is the hostname of the server. So it seems to be authenticating as 'Guest'?? To verify this, I enabled the Guest account on the 'server' PC and then added Guest as an allowed user within Office Accounting (this simply creates the user in SQL and gives it an appropriate database role). Sure enough, My Windows 8 PC was then able to connect to the database when using Office Accounting. Clearly, having users authenticate as 'Guest' stinks from a security and auditing standpoint. So what I need are some ideas for how to work around this. I've tried switching the Windows 8 PC to a 'local account' and that works too, but requires giving up significant functionality on the Windows 8 PC. What I really need is a way to force the Windows 8 PC to use a specific set of credentials when connecting to the remote SQL instance. Office Accounting takes the logged in username, which is my LiveID and doesn't correspond to any Windows user name. Anyone solved this issue?

  Read the article

• Connecting both WAN and LAN ports to the same hub

  - by C. Lee

  For some reason I wish to connect the WAN port and the LAN port on a router to the same hub and make the hub is connected to both networks, the Internet and a private network. Below is a diagram of the network configuration I'd like to build. I tried this and it didn't work as expected. PC 1 has no problem, but PC 2 cannot connect to the Internet. When I ping 192.168.0.1 from PC 2, all packets are lost. It works well when PC 2 is connected directly to the router. What's the problem with the network configuration above?

  Read the article

• Can't add printer on Windows XP

  - by SuperFurryToad

  I've added a HP 4250 printer to about half a dozen Windows XP PCs in our office without any problems whatsoever, but for some reason I haven't been able to add it to one particular PC today. I go through the Add Printer wizard to add a local printer attached to the PC, enter the new port number as a Standard TCP/IP Port, install the driver. At the end of the wizard I get the following error message: Full error message: "windows cannot connect to the printer. either the printer name was typed incorrectly, or the specified printer has lost its connection to the server." This doesn't make any sense as I am able to ping the printer from the PC. The print spooler is running, and any firewall software on the local PC is switched off.

  Read the article

• MicroSD card isn't detected by computer, apparently usable only with phone

  - by paulcjoubert

  I have a 4GB MicroSD card that apparently only works (in the sense that the device detects and can read and write from and to the card) with my old Nokia XpressMusic 5800 phone. I have taken pictures and recorded voice notes that were saved on the card. These are accessible after the card has been removed, which tells me that the problem isn't with the card. The card could also not be locked to the phone as it would at least be detected by a computer and it would be able to write raw data to it with dd, such as /dev/zero. Also, the card is not the Nokia card that came with the phone and I have done nothing that would have caused it to be locked. (I could not find anything on Nokia's website that helps, but then again... my search was not THAT thorough.) The card works on no other device that I have tried so far. I have tried it in my Canon camera (through an adapter), but it refuses to even boot with the card inserted. My card reader (via USB cable and hub) is detected as /dev/sdx with or without the card inserted. When trying to access the card I get an "No medium found". dmesg does not report any change at all when inserting and removing the card. I would obviously like to use my card on other devices - the phone is quite old - and even a likely explanation would help. Thankyou in advance! EDIT 1: I can use the card by connecting the phone to my computer, but this is impractical and would not allow me to use the card in any other device. EDIT 2: The data on the card is not important to me at all.

  Read the article

• Numlock on when computer is off

  - by George Duckett

  I have a desktop PC which was recently moved. Since moving I've noticed that even while the PC is turned off (but wall socket turned on) the NumLock LED on the keyboard is on. It may have been doing this before the move, but I've only noticed it now. Maybe it matters that the keyboard is connected via a shared mouse/keyboard PS/2 port and I'm running Windows 7. I've not checked whether the LEDs are just keeping whatever state they were in when I turned the PC off but will do this if that information could be relevant. Why does the led stay on when the PC is turned off and how can I prevent this?

  Read the article

• File Transfer with a double SSH login.

  - by Harpal

  I'm have trouble transfering files again from my work PC, which is a linux machine to my home windows PC. My work has changed it so I now need to SSH twice before I can access my PC. So I need to: ssh [email protected] password: xxxxx I then need to do it again. ssh computer_name password: xxxxx I've tried accessing directly via my computers IP but to of no avail. Is there a way I can use pscp or file zilla to ssh twice so I can transfer files?

  Read the article

• Basic questions about network topologies

  - by laoshanlung

  I have just started learning about network topologies, but there are a lot of confusion about different types of network topologies i have learnt so far. First of all, BUS topology. If i have like 100 PCs in the same wire connected using BUS topology, and the network connection speed is 100Mbps, then each PC will have a connection of 1Mbps, right ? With the same scenario, if i connect those 100 PCs using STAR topology, then each PC will have a connection of 100Mbps ? Then with the TREE topology, i divide the system into 10 sub-system (10 tree branches) , each branch has 10 PCs, then i will have other 10 small "BUS-topology" networks each one will have a connection of 10Mbps and therefore each PC will also have 10Mbps ? And the last one is RING topology, 100 PCs, each PC will have 100Mbps connection ?

  Read the article

• Which free VNC server works well with Windows 7 and how to advertise it via Samba for control by a M

  - by GJ

  Hi I need to control a Windows 7 PC via VNC from a Mac in an office LAN. Since the IPs are dynamically assigned, I'd like the PC to appear in my "Places" and in the automatically detected nearby servers in VNC client I'm using -- both of which require the PC to advertise its VNC server via Samba (right?). I tried installing ultravnc, which works when I access it directly by IP, but it doesn't seem to advertise itself in the network. Any ideas?

  Read the article

• Remote support via VPN without split tunnel

  - by Robe Eleckers

  my title might not be very clear, but I'll explain my setup in more detail now. We have several customers (companies) that need to be remotely supported. At these customers we have servers running with our software that needs to be serviced. These servers are (almost) never connected to the internet. For this we have multiple PC's running VPN clients. These PC's run a VNC server so our service engineers can login from their home laptop remotely to these PC's and connect from there to our customer via the VPN connection on the PC. The problem is however that several customers do not allow split tunneling. That means that when we connect via VPN to such a customer the VNC connection drops. Our current workaround is using a Citrix VM which we control via XenCenter console, but it's quite slow. Are there common solutions to handle this?

  Read the article

• What are the quality metrics for RAM?

  - by Hi-Tech KitKat Android

  I have searched RAM and i found there are given some specification for the same capacity RAM, What are the difference and performance comparison between these? Like RAM1 General Brand Transcend Memory Type 2 GB (8 x 128 MB) DDR2 DIMM Memory Standard DDR2-800/PC-6400 Compatible Device PC Pins 240-pin Burst Length 4, 8 Buffered/Unbuffered Unbuffered Memory Memory Clock 400 MHz Technology DDR2 SDRAM Memory CAS Latency 4, 5, 6 RAM 2 General Brand Transcend Memory Type 2 GB (8 x 128 MB) DDR2 DIMM Memory Standard DDR2-667/PC2-5300 Compatible Device PC Pins 240-pin Burst Length 4, 8 Buffered/Unbuffered Unbuffered Memory Memory Clock 333 MHz Technology DDR2 SDRAM Memory CAS Latency 3, 4, 5 RAM3 General Brand Kingston Memory Type 2 GB (64 x 256 MB) 800 MHz DDR2 DIMM Compatible Device PC Pins 240-pin Error Check Non-ECC Buffered/Unbuffered Unbuffered Memory Memory Clock 200 MHz Technology DDR2 SDRAM Memory CAS Latency 6 What are the affect of the following Memory Type(given as 8 x 128 MB) Memory Clock (given in MHz) CAS Latency (given as 4,5,6) my Requirement is 2 GB DDR2 Type Desktop Please help

  Read the article

• Strip my windows NTFS disk of all ACLs

  - by Alain Pannetier

  When you purchase a windows PC nowadays, you don't actually "own" the whole disk... There are so many ACLs on each folder that there are portions of it you actually can access only through a complex sequence of actions requiring skills well beyond the average PC user. You have to drill down to deeply buried dialog boxes accessible through concealed buttons. You have to understand at which level of the hierarchy you have to take ownership, remove ACLs etc... Yet when you think of it, that's your PC, that's what the "P" of PC originally stand for... So I'm toying with the idea of just stripping the disk of all ACLs I just purchased and leave standard file protections do the basic protection work... Just like previous century Windows used to do... (before I chmod -R 777 ;-) Has anybody done that already and nevertheless survived in reasonably good shape for a reasonable amount of time ? Any technical advice to do that ? Powershell script ? basic script using iCACLS ?

  Read the article

• XP shared folders not accessible after BIOS changed

  - by stijn

  Here's what worked for over a year: PC A runs Windows 7, PC B runs Windows XP. Both are on the same subnet behind a router. A uses user account X, but logs in to PC B using the Administrator account. PC B is a Dell Precision 470. A known problem with these is that sometimes when plugging in their power cable they somehow loses all BIOS settings. This happened yesterday. After this happens Windows won't boot, because the default BIOS setting is 'RAID ON' while there is no RAID configured. No problem though, changing the BIOS settings to 'RAID OFF' makes it boot without problems. Note that in the meantime, nothing config-related was changed on machine A. It wasn't even on. Indeed after doing this, everything is fine. Everything includes all normal operations, remote desktop from PC A to PC B, running Synergy between A and B, accessing shared folders from B to A. But accessing the shared folders on B from A does not work any more. I tried pretty much everything I found via Google (fiddling with policies/registry kes/...) but no avail. > ping -a 192.168.2.2 Pinging A [192.168.2.2] with 32 bytes of data: Reply from 192.168.2.2: bytes=32 time<1ms TTL=128 > net view \\192.168.2.2 System error 5 has occurred. Access is denied. > net use /persistent:no K: \\A\myshare /user:A\USERNAME PASSWORD > net use /persistent:no K: \\192.168.2.2\myshare /user:192.168.2.2\USERNAME PASSWORD > net use /persistent:no K: \\192.168.2.2\myshare /user:USERNAME PASSWORD System error 86 has occurred. The specified network password is not correct. A solution to this would be great: I haven't been able to do any work since yesterday ;] update after taking the hard drive out of B and putting it in another Precision 470 with almost exactly the same hardware (at first sight, only the video card differs) the shared folders work.. Putting the disk back into A, same problem remains. Why does this depend on hardware, and more important, on which hardware?

  Read the article

• SSH Tunnel for Remote Desktop via Intermediary Server

  - by Mihai Todor

  I've seen many examples of SSH tunnels on the nets, but I'm still having no luck with this. Here's the setup: Windows 7 PC in a private network, sitting behind a firewall, with PowerShellInsider SSH server set up and working fine. Public access Linux server, which has access to the PC. Windows 7 laptop, at home, from which I wish to do remote desktop on the PC. Now, here's what I've tried so far: SSH tunnel from my laptop to the Linux server: ssh -f my_user@LINUX_SERVER -L 6666:LINUX_SERVER_IP:6666 -N SSH to the Linux server where I've set up a tunnel to the PC: ssh -f 'PRIVATE_DOMAIN\my_user'@PC_NAME -L 6666:PC_IP:3389 -N Unfortunately, I must be doing something wrong, because it doesn't seem to work. Any ideas why or, at least, any suggestions on how can I try to debug this setup? At the moment, I have access to all 3 machines (non-root on Linux), so I can test whatever I want...

  Read the article

• Reserve internet connection.

  - by amouniverso

  I have the router D-link 804HV that have 20mbit\s internet via PPoE tunnel . It connect three PC with Windows Xp to my home net. One of three my PC have reserve stability wi-fi internet connection. How can I use the wi-fi connection as reserve if the router connection is not available? I try to set the Wi-fi PC as gate for the other two, but it's not working.

  Read the article

< Previous Page | 97 98 99 100 101 102 103 104 105 106 107 108  | Next Page >