Search Results

Search found 13341 results on 534 pages for '1 obiee performance tuning'.

Page 102/534 | < Previous Page | 98 99 100 101 102 103 104 105 106 107 108 109  | Next Page >

• Windows 8 x64 with VMWare Workstation or inside ESXi

  - by Dommer

  I need to run several virtual machines on a core i7-920 box with 12GB or RAM and a 256GB SSD to host the VMs. It also has a Highpoint RocketRaid 2720SGL RAID controller with a 12TB RAID 5 array. I want one of my VMs to run Windows 8 x64, to have access to the RAID array as a native disk (not as networked drives and it needs to run at full speed) and to be able to send files quickly across the network. Initially I thought I'd try to do this using ESXi 5, but I have been unable to find any working RAID drivers for the RR2720SGL and it is not on the HCL for ESXi 5. In light of this, I have installed Windows 8 x64 on the hardware and am thinking of installing VMWare Workstation and running my VMs inside there. I guess my questions are these: How does VMWare Workstation 9 perform compared to ESXi 5? In the real world I mean? Presumably installing Win 8 as the host OS will give me way better performance for that Win 8 machine than Win 8 running under ESXi? I should stick with Windows 8 x64 as the host OS, right? If I install a domain controller VM inside my Win 8 box and join the Win 8 machine to that domain, am I insane (I would guess the Win 8 machine wouldn't see the domain controller until it finished starting everything up, but I don't think that matters)?! is it feasible to give metrics like this and if so, what is the likely value of x? 25%? 50%? 75%? Win 8 under ESXi runs x% as fast as Win 8 installed bare metal.

  Read the article

• Best SSD tweaks for Windows 7

  - by Nick Berardi

  I have seen many articles about tweaking an SSD, but many of them seem outdated, or too broad (read all Windows XP, Vista, and Windows 7 general tweaks). And I know that Windows 7 has been specifically tweaked for SSD by the Windows team, so I don't want to do something that was written for Windows XP in mind and end up circumventing something the Windows team has specifically designed in to Windows 7. So my question is what are the best SSD tweaks for Windows 7 that you have found to get the performance out of your drive? I hope to make a comprehensive list in the answers below so there won't be so much disinformation in the forums about what to do and what not to do. Here are a few that I see posted up on the forums alot, and some questions to get the discussion started: Disabling Superfetch. Yes or No Disabling Page File or limiting it to a really small size such as 500 MB. Disabling Indexing. Yes or No Disabling Defragmenting. Yes or No What are your thoughts do you have any that have worked for you? When providing an answer please do your best to back it up with a reason and possibly some documentation from MSDN, TechNet, or another credible source.

  Read the article

• Measure Upload Speed between a client and our server

  - by tresstylez

  We host a SAAS application specially customized for multiple clients. For one customer in particular -- they are reporting sporadic performance issues from various locations on their network, in particular UPLOADING documents through a form on our website. The client claims they have "bandwidth to spare" and that utilization of their "pipe" is so low that it MUST be our application, but our application has MANY clients and all features are working fine for all other clients. Interestingly enough -- DOWNLOADS (ie. just accessing the website, or downloading documents) is working fine. Speed test shows that they should get 1.2Mbps UP. So, a 3MB file should take 20 secs to upload. It takes 60+ seconds on their network. Sometimes even small files take OVER 10 minutes to upload or they timeout. Pings and Traceroutes don't show any abnormally long hops or response times. They claim other SAAS applications they use allow them to upload just fine. Both IT teams are working together to resolve this issue. What kind of data can I request from the clients to begin ruling things out. Seems like we need to somehow measure LATENCY of the networks involved or even at the switch level, we need to understand if packets are getting dropped somewhere and why. Where should I start? Any help is appreciated. I'll provide more info upon requests

  Read the article

• (Win7) Gets stuck with ~1% CPU. Especially with multithreading

  - by meow

  Windows 7 32 bit, up to date, Intel i7 860. (For some reason the company runs 32bit Windows everywhere.) I tried to update all motherboard drivers etc. as far as possible. I have a performance issue with a machine which appears in connection with multithreading (or so I think). As an example (and where I most often see it, but it appears on other programs as well): ProteoWizard is a file conversion tool for mass spectrometry files. I can add a list of files and it will attempt to process up to 8 files in parallel (quadcore x 2 threads/core). If I choose 1 to 6 files, I start the process and it goes straight through. If I have =7 files in the queue, conversion goes to ~20%, then gets stuck for 15 seconds, then continues again, always in "chunks" of a few % before getting stuck again. During the time the process is stuck, CPU is at 1%. RAM is not limiting, it is maybe at 70% or so and not going up. I don't get the same problem on other, even slower machines. The computer gets also stuck at 1% CPU doing nothing on other occasions, but for multithreading it is most frequent. Where should I look for the problem?

  Read the article

• TortoiseSVN client slows Explorer to a crawl in Windows XP running in Parallels

  - by Cory Larson

  I thought I'd make my first SuperUser question relatively simple, though it's the kind of question that may not get many responses as I'm not directly involved with the issue. A colleague does his development in Windows XP running in Parallels on his Mac. We've just migrated our VSS repository to SVN, and we've gone with TortoiseSVN as our client of choice with the Ankhsvn plugin for Visual Studio. On his XP instance, after installing TortoiseSVN, browsing through folders using Explorer is extremely slow; about 15 - 30 seconds before the contents of the next folder displays. It's the slowest when opening My Computer. Once he reaches a folder that contains the working content of an SVN project, Explorer behaves quickly again as expected. It seems that TortoiseSVN may be spending a bunch of time searching subfolders for stuff so it can do its icon-overlay thing, but that's just a guess. I've used TortoiseSVN for years on both XP and Vista on far less powerful machines without any issues with Explorer, so I'm attributing the slowness to it being run in a VM, though that may not be the actual issue. So has anyone encountered similar performance issues, and/or know of a fix? Keep in mind that any requests to make changes to his configuration will need to be communicated and thus my response time might be slow. Thanks everyone!

  Read the article

• What may the reason of slowness be (see details in message body)?

  - by Ivan

  I've got a really weird situation I'm beating to solve. A performance problem which looks really like an empty waiting sequence set in code (while it probably isn't so). I've got a pretty powerful dedicated server (10 GB RAM, eight Xeon cores, etc) running Ubuntu 10.04 with all the functionality services (except OpenVPN server used to provide secure access to clients) deployed in separate VirtualBox (vboxheadless) machines (one for the company e-mail server, one for web server and one for accounting/crm server (Firebird + proprietary app server working with Delphi-made clients)). CPU load (as "top" says) is almost always near zero. Host system RAM is close to 100% usage but not overloaded (as very little swapping gets used, and freed (by stopping one of VMs) memory doesn't get reused any quickly). Approximately 50% of guests RAM is used. iostat usually shows near zero %util. Network bandwidth seems to be underused. But the accounting/crm client (a Win32 Delphi application run on WinXP machines) software works hell-slow with this server (and works much better using an inside-LAN Windows server). I just can't imagine what can make it be slow if there are so plenty of CPU, RAM, HDD and bandwidth resources available on clients and on the server even in their hardest moments. Saying bandwidth is underused I not only know that clients and the server are connected to the Internet with a bigger channels than really used (which leaves the a chance they may have a bottleneck of a sort on the route between them), I've tested bandwidth between clients and the server by copying files among them.

  Read the article

• Upgrade or replace?

  - by Felix

  My current PC is about four years old, although I have made upgrades to it throughout its existence. The current specs are: (old) Intel Pentium D 2.80Ghz (32K L1 / 2M L2), Gigabyte 945GCMX-S2 motherboard (old) 2.5GB DDR2 (slot0: 512MB @ 533Mhz; slot1: 2GB @ 667Mhz) (new) HIS Radeon HD 4670 - I think this is limited by the motherboard not supporting PCIe 2.0 (?) (old) WD Caviar 160GB - pretty slow (new) WD Caviar Black 640GB (if any more specs are relevant, let me know and I'll add them) Now, on to my question. I've been having performance issues lately, both in video games and in intensive applications. A couple of examples: Android application development (running Eclipse and the Android emulator) is painfully slow (on Linux). I only realized this when, at my new job as an Android dev, both tools are MUCH quicker. (I'm not sure what CPU I have there) The guys at my new job got me NFS Hot Pursuit, in which I barely get like 5-10FPS, even with graphics options turned all the way down My guess is that the bottleneck in my system is my CPU, so I'm thinking of upgrading to a Quad Core i5 + new motherboard + 4GB DDR3 (or more, 'cause I know you'll all jump and say 8GB minimum). Now: Is that a good idea? Is my CPU really a bottleneck, or is the whole system too old and I should replace it? I run Windows 7 on the old, 160GB HDD (which is on IDE, by the way). Could this slow down games as well? Should I get a new drive for Windows if I want to play new games? I know nothing about power supplies. Could that be a problem / will it be a problem if I upgrade to an i5? How come DiRT2 works on full graphics settings (pretty amazing graphics by the way) and NFS Hot Pursuit pulls only 5-10FPS?

  Read the article

• How can I optimize my ajax calls to deliver at 60ms.

  - by Quintin Par

  I am building an autocomplete functionality for my site and the Google instant results are my benchmark. When I look at Google, the 50-60 ms response time baffle me. They look insane. In comparison here’s how mine looks like. To give you an idea my results are cached on the load balancer and served from a machine that has httpd slowstart and initcwnd fixed. My site is also behind cloudflare From a server side perspective I don’t think I can do anything more. Can someone help me take this 500 ms response time to 60ms? What more should I be doing to achieve Google level performance? Edit: People, you seemed to be angry that I did a comparison to Google and the question is very generic. Sorry about that. To rephrase: How can I bring down response time from 500 ms to 60 ms provided my server response time is just a fraction of ms. Assume the results are served from Nginx - Varnish with a cache hit. Here are some answers I would like to answer myself assume the response sizes remained more or less the same. Ensure results are http compressed Ensure SPDY if you are on https Ensure you have initcwnd set to 10 and disable slow start on linux machines. Etc. I don’t think I’ll end up with 60 ms at Google level but your collective expertise can help easily shave off a 100 ms and that’s a big win.

  Read the article

• Ubuntu's garbage collection cron job for PHP sessions takes 25 minutes to run, why?

  - by Lamah

  Ubuntu has a cron job set up which looks for and deletes old PHP sessions: # Look for and purge old sessions every 30 minutes 09,39 * * * * root [ -x /usr/lib/php5/maxlifetime ] \ && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth 1 \ -maxdepth 1 -type f -cmin +$(/usr/lib/php5/maxlifetime) ! -execdir \ fuser -s {} 2> /dev/null \; -delete My problem is that this process is taking a very long time to run, with lots of disk IO. Here's my CPU usage graph: The cleanup running is represented by the teal spikes. At the beginning of the period, PHP's cleanup jobs were scheduled at the default 09 and 39 minutes times. At 15:00 I removed the 39 minute time from cron, so a cleanup job twice the size runs half as often (you can see the peaks get twice as wide and half as frequent). Here are the corresponding graphs for IO time: And disk operations: At the peak where there were about 14,000 sessions active, the cleanup can be seen to run for a full 25 minutes, apparently using 100% of one core of the CPU and what seems to be 100% of the disk IO for the entire period. Why is it so resource intensive? An ls of the session directory /var/lib/php5 takes just a fraction of a second. So why does it take a full 25 minutes to trim old sessions? Is there anything I can do to speed this up? The filesystem for this device is currently ext4, running on Ubuntu Precise 12.04 64-bit. EDIT: I suspect that the load is due to the unusual process "fuser" (since I expect a simple rm to be a damn sight faster than the performance I'm seeing). I'm going to remove the use of fuser and see what happens.

  Read the article

• Ubuntu 12.04 VirtualBox on powerful W7 quite slow

  - by wnstnsmth

  I own a Thinkpad T420s with 8GB RAM, 160 GB SSD and a quite fast i7 processor. Summa summarum a very fast computer that works perfectly. Now, I am not very impressed by the performance of my Ubuntu 12.04 virtual machine running on VirtualBox 4.1.18. I assume that Virtual Machines are always a bit slower than the guest system, still I think it should be more performant given the hardware settings I give it: 4096 MB RAM 1 CPU without CPU limitation (I would like to give it more but then it does not seem to work - I am not experienced in this maybe somebody could give me advice on this too) Activated PAE/NX, VT-x/AMD-V and Nested Paging 96 MB Graphics Memory (no 2D or 3D acceleration) ~ 14 GB disk space, currently about 7 GB are used Maybe I misconfigured something, could you give me a hint please? Thanks! Edit: What I mean by slow is that for example switching tabs in the browser (whether FF or Chrome) only goes with a 0.5s delay or something, as well as switching application windows and/or double-clicking applications in the dock to get all open windows.. opening Aptana takes about a minute whereas opening something like Photoshop on the guest system takes 5 seconds

  Read the article

• New i7 is slower than old Core 2 Duo? Why? (BIOS programming)

  - by DrChase

  I've always wondered why the companies who make BIOS' either have terrible engineering psychologists or none at all. But without wasting your time further with random speculative questions, my real question is as follows: Why does my new computer run slower than my old computer? Old Computer: Intel Core 2 Duo CPU @ 3.0 Ghz (stock) 4GB OCZ DDR2 800 RAM Wolfdale E8400 mb nVidia GeForce 8600 GT New Computer: Intel Core i7 920 @ ~3.2 Ghz 6 GB OCZ DDR3 1066 RAM EVGA x58 SLI LE motherboard nVidia GeForce GTX 275 Vista x64 Home Premium on both. "Run slower" is defined as: - poorer FPS performance in the same games, applications - takes longer to start up - general desktop usage (checking email, opening up files, running exe's) is noticeably slower At first I thought I must've not set something up in the BIOS or something. But I have no idea how to set anything in the bios except for "Dummy O.C.", which brought me to ~3.2 Ghz. But beyond that I have no idea. I've been reading stuff about "ram timing" and voltages and the like but I really have no idea about that stuff. I'm a psychologist who has a basic understanding in building his own computers, not a computer scientist. Can someone give me some wisdom that might guide me to the reason my new computer is worse than my older one? I'm sorry if this is a bad question, or not appropriate to SO. I'm just pretty frustrated now and you all have helped me in the past so I figured I'd give it a shot. Thanks for your time.

  Read the article

• My system is always disk-bound (the disk light is always on). Why is this?

  - by Scoobie

  I have been given a laptop by the good folks at my company on which to do my work (Java development). I usually use eclipse as my primary development platform. The laptop is a Dell D830 and runs Windows 7 - 32 bit. Although the processor supports a 64 bit instruction-set, licensing limits me to running the 32 bit OS. The HDD is a WD1600BEVT (Western Digital). I have noticed that my disk is always very slow. Windows start up is usually pretty quick, however as soon as I log on, my disk light stays on and usually, the laptop takes about 4 minutes (after logging in -- immediately upon getting the prompt to press Ctrl + Alt + Del to log in) before it's usable. Questions: Is this expected behavior? What can I do to examine the disk and determine the cause of the problem? What can I do to improve my disk's performance? Any optimizations you may be able to suggest? Other Questions: Some have suggested running Process Monitor (from sysinternals), but how would i get the log since start up? Instead of trying to fix this myself, should I simply push this onto the system administrator? Thanks all.

  Read the article

• Comparing 128MB GeForce 8600GT and 512MB Radeon X1650

  - by Synetech inc.

  Hi, I'm trying to determine which is the better of these two video cards: 128MB Nvidia GeForce 8600GT card while the other has a 512MB ATI Radeon X1650 card. Both cards are the upper-level mid-range versions of their respective series. On the one hand, the ATI has substantially more VRAM, but the Nvidia supports D3D 10 and SM4.0 as opposed to D3D 9.0c/SM3.0 that the ATI supports. Also, I have always heard better things about Nvidia cards compared to ATI cards. I'm trying to find some advice on which one is better, but I can't find any actual comparisons or anything for these specific cards (the comparisons I can find are only similar ones like the X1650 Pro or 8600GT PCI-E), so I figure that what I need to know is whether the extra VRAM is that important. Looking at the ATI table and the Nvidia table seems to indicate that the Nvidia is better, but then again, the Nvidia table also says that the GeForce 8600GT is a PCI-E card with at least 256MB even though the card in question is an AGP with 128MB. (:-?) (It looks like the ATI card is not supported in Windows 7 while the Nvidia card is, which I suppose is also a factor, though not quite as immediately relevant as performance.) Any ideas? Thanks a lot.

  Read the article

• How can I avoid garbage collection delays in Java games? (Best Practices)

  - by Brian

  I'm performance tuning interactive games in Java for the Android platform. Once in a while there is a hiccup in drawing and interaction for garbage collection. Usually it's less than one tenth of a second, but sometimes it can be as large as 200ms on very slow devices. I am using the ddms profiler (part of the Android SDK) to search out where my memory allocations come from and excise them from my inner drawing and logic loops. The worst offender had been short loops done like, for(GameObject gob : interactiveObjects) gob.onDraw(canvas); where every single time the loop was executed there was an iterator allocated. I'm using arrays (ArrayList) for my objects now. If I ever want trees or hashes in an inner loop I know that I need to be careful or even reimplement them instead of using the Java Collections framework since I can't afford the extra garbage collection. That may come up when I'm looking at priority queues. I also have trouble where I want to display scores and progress using Canvas.drawText. This is bad, canvas.drawText("Your score is: " + Score.points, x, y, paint); because Strings, char arrays and StringBuffers will be allocated all over to make it work. If you have a few text display items and run the frame 60 times a second that begins to add up and will increase your garbage collection hiccups. I think the best choice here is to keep char[] arrays and decode your int or double manually into it and concatenate strings onto the beginning and end. I'd like to hear if there's something cleaner. I know there must be others out there dealing with this. How do you handle it and what are the pitfalls and best practices you've discovered to run interactively on Java or Android? These gc issues are enough to make me miss manual memory management, but not very much.

  Read the article

• MySQL performance

  - by kapil.israni

  Hi, I have this LAMP application with about 900k rows in MySQL and I am having some performance issues. Background - Apart from the LAMP stack , there's also a Java process (multi-threaded) that runs in its own JVM. So together with LAMP & java, they form the complete solution. The java process is responsible for inserts/updates and few selects as well. These inserts/updates are usually in bulk/batch, anywhere between 5-150 rows. The PHP front-end code only does SELECT's. Issue - the PHP/SELECT queries become very slow when the java process is running. When the java process is stopped, SELECT's perform alright. I mean the performance difference is huge. When the java process is running, any action performed on the php front-end results in 80% and more CPU usage for mysqld process. Any help would be appreciated. MySQL is running with default parameters & settings. Software stack - Apache - 2.2.x MySQL -5.1.37-1ubuntu5 PHP - 5.2.10 Java - 1.6.0_15 OS - Ubuntu 9.10 (karmic)

  Read the article

• jQuery performance

  - by jAndy

  Hi Folks, imagine you have to do DOM manipulation like a lot (in my case, it's kind of a dynamic list). Look at this example: var $buffer = $('<ul/>', { 'class': '.custom-example', 'css': { 'position': 'absolute', 'top': '500px' } }); $.each(pages[pindex], function(i, v){ $buffer.append(v); }); $buffer.insertAfter($root); "pages" is an array which holds LI elements as jQuery object. "$root" is an UL element What happens after this code is, both UL's are animated (scrolling) and finally, within the callback of animate this code is executed: $root.detach(); $root = $buffer; $root.css('top', '0px'); $buffer = null; This works very well, the only thing I'm pi**ed off is the performance. I do cache all DOM elements I'm laying a hand on. Without looking too deep into jQuery's source code, is there a chance that my performance issues are located there? Does jQuery use DocumentFragments to append things? If you create a new DOM element with var new = $('<div/>') it is only stored in memory at this point isnt it?

  Read the article

• WF performance with new 20,000 persisted workflow instances each month

  - by Nikola Stjelja

  Windows Workflow Foundation has a problem that is slow when doing WF instances persistace. I'm planning to do a project whose bussiness layer will be based on WF exposed WCF services. The project will have 20,000 new workflow instances created each month, each instance could take up to 2 months to finish. What I was lead to belive that given WF slownes when doing peristance my given problem would be unattainable given performance reasons. I have the following questions: Is this true? Will my performance be crap with that load(given WF persitance speed limitations) How can I solve the problem? We currently have two possible solutions: 1. Each new buisiness process request(e.g. Give me a new drivers license) will be a new WF instance, and the number of persistance operations will be limited by forwarding all status request operations to saved state values in a separate database. 2. Have only a small amount of Workflow Instances up at any give time, without any persistance ofso ever(only in case of system crashes etc.), by breaking each workflow stap in to a separate worklof and that workflow handling each business process request instance in the system that is at that current step(e.g. I'm submitting my driver license reques form, which is step one... we have 100 cases of that, and my step one workflow will handle every case simultaneusly). I'm very insterested in solution for that problem. If you want to discuss that problem pleas be free to mail me at [email protected]

  Read the article

• Figuring out the Nyquist performance limitation of an ADC on an example PIC microcontroller

  - by AKE

  I'm spec-ing the suitability of a dsPIC microcontroller for an analog-to-digital application. This would be preferable to using dedicated A/D chips and a separate dedicated DSP chip. To do that, I've had to run through some computations, pulling the relevant parameters from the datasheets. I'm not sure I've got it right -- would appreciate a check! (EDITED NOTE: The PIC10F220 in the example below was selected ONLY to walk through a simple example to check that I'm interpreting Tacq, Fosc, TAD, and divisor correctly in working through this sort of Nyquist analysis. The actual chips I'm considering for the design are the dsPIC33FJ128MC804 (with 16b A/D) or dsPIC30F3014 (with 12b A/D).) A simple example: PIC10F220 is the simplest possible PIC with an ADC Runs at clock speed of 8MHz. Has an instruction cycle of 0.5us (4 clock steps per instruction) So: Taking Tacq = 6.06 us (acquisition time for ADC, assume chip temp. = 50*C) [datasheet p34] Taking Fosc = 8MHz (? clock speed) Taking divisor = 4 (4 clock steps per CPU instruction) This gives TAD = 0.5us (TAD = 1/(Fosc/divisor) ) Conversion time is 13*TAD [datasheet p31] This gives conversion time 6.5us ADC duration is then 12.56 us [? Tacq + 13*TAD] Assuming at least 2 instructions for load/store: This is another 1 us [0.5 us per instruction] Which would give max sampling rate of 73.7 ksps (1/13.56) Supposing 8 more instructions for real-time processing: This is another 4 us Thus, total ADC/handling time = 17.56us (12.56us + 1us + 4us) So expected upper sampling rate is 56.9 ksps. Nyquist frequency for this sampling rate is therefore 28 kHz. If this is right, it suggests the (theoretical) performance suitability of this chip's A/D is for signals that are bandlimited to 28 kHz. Is this a correct interpretation of the information given in the data sheet in obtaining the Nyquist performance limit? Any opinions on the noise susceptibility of ADCs in PIC / dsPIC chips would be much appreciated! AKE

  Read the article

• Naming multi-instance performance counters in .NET

  - by Roger Lipscombe

  Most multiple instance performance counters in Windows seem to automatically(?) have a #n on the end if there's more than one instance with the same name. For example: if, in Perfmon, you look under the Process category, you'll see: ... dwm explorer explorer#1 ... I have two explorer.exe processes, so the second counter has #1 appended to its name. When I attempt to do this in a .NET application: I can create the category, and register the instance (using the PerformanceCounterCategory.Create that takes a CounterCreationDataCollection). I can open the counter for write and write to it. When I open the counter a second time, it opens the same counter. This means that I have two applications fighting over the counters. The documentation for PerformanceCounter.InstanceName states that # is not allowed in the name. So: how do I have multiple-instance performance counters that are actually multiple instance? And where the second (and subsequent) instances get #n appended to the name? That is: I know that I can put the process ID (e.g.) on the instance name. This works, but has the unfortunate side effect that restarting the process results in a new PID, and Perfmon continues monitoring the old counter.

  Read the article

• Improving the performance of XSL

  - by Rachel

  I am using the below XSL 2.0 code to find the ids of the text nodes that contains the list of indices that i give as input. the code works perfectly but in terms for performance it is taking a long time for huge files. Even for huge files if the index values are small then the result is quick in few ms. I am using saxon9he Java processor to execute the XSL. <xsl:variable name="insert-data" as="element(data)*"> <xsl:for-each-group select="doc($insert-file)/insert-data/data" group-by="xsd:integer(@index)"> <xsl:sort select="current-grouping-key()"/> <data index="{current-grouping-key()}" text-id="{generate-id( $main-root/descendant::text()[ sum((preceding::text(), .)/string-length(.)) ge current-grouping-key() ][1] )}"> <xsl:copy-of select="current-group()/node()"/> </data> </xsl:for-each-group> </xsl:variable> In the above solution if the index value is too huge say 270962 then the time taken for the XSL to execute is 83427ms. In huge files if the index value is huge say 4605415, 4605431 it takes several minutes to execute. Seems the computation of the variable "insert-data" takes time though it is a global variable and computed only once. Should the XSL be addessed or the processor? How can i improve the performance of the XSL.

  Read the article

• APplication performance issue : SqlServer & Oracle

  - by Mahesh

  Hi, We have a applicaiton in Silverlight,WCF, NHibernate. Currently it is supporting SQL Serve and Oracle database. As it's huge data, it is running ok on SQL Sevrer. But on Oracle it is running very slow. For one functionality it takes 5 Sec to execute on SQL Server and 30 Sec on Oracle. I am not able to figure out what will be issue. Two things that i want to share with you about our database. 1) Database: contains one base table contains column of type SQLServer: [Text] Oracle: [NCLOB] 2) Our database structure is too much normalized. May be in the oracle i have used NCLOB, that is the cause of the performance. I mean i don't know the details about it.... Can anyone please let me know what will be cause? Or Which actions do i need to follw to improve the performance as equal as SqlServer.? Thanks in advance. Mahesh.

  Read the article

• Performance difference in for loop condition?

  - by CSharperWithJava

  Hello all, I have a simple question that I am posing mostly for my curiousity. What are the differences between these two lines of code? (in C++) for(int i = 0; i < N, N > 0; i++) for(int i = 0; i < N && N > 0; i++) The selection of the conditions is completely arbitrary, I'm just interested in the differences between , and &&. I'm not a beginner to coding by any means, but I've never bothered with the comma operator. Are there performance/behavior differences or is it purely aesthetic? One last note, I know there are bigger performance fish to fry than a conditional operator, but I'm just curious. Indulge me. Edit Thanks for your answers. It turns out the code that prompted this question had misused the comma operator in the way I've described. I wondered what the difference was and why it wasn't a && operator, but it was just written incorrectly. I didn't think anything was wrong with it because it worked just fine. Thanks for straightening me out.

  Read the article

• How can I determine PerlLogHandler performance impact?

  - by Timmy

  I want to create a custom Apache2 log handler, and the template that is found on the apache site is: #file:MyApache2/LogPerUser.pm #--------------------------- package MyApache2::LogPerUser; use strict; use warnings; use Apache2::RequestRec (); use Apache2::Connection (); use Fcntl qw(:flock); use File::Spec::Functions qw(catfile); use Apache2::Const -compile => qw(OK DECLINED); sub handler { my $r = shift; my ($username) = $r->uri =~ m|^/~([^/]+)|; return Apache2::Const::DECLINED unless defined $username; my $entry = sprintf qq(%s [%s] "%s" %d %d\n), $r->connection->remote_ip, scalar(localtime), $r->uri, $r->status, $r->bytes_sent; my $log_path = catfile Apache2::ServerUtil::server_root, "logs", "$username.log"; open my $fh, ">>$log_path" or die "can't open $log_path: $!"; flock $fh, LOCK_EX; print $fh $entry; close $fh; return Apache2::Const::OK; } 1; What is the performance cost of the flocks? Is this logging process done in parallel, or in serial with the HTTP request? In parallel the performance would not matter as much, but I wouldn't want the user to wait another split second to add something like this.

  Read the article

• Improve performance of searching JSON object with jQuery

  - by cale_b

  Please forgive me if this is answered on SO somewhere already. I've searched, and it seems as though this is a fairly specific case. Here's an example of the JSON (NOTE: this is very stripped down - this is dynamically loaded, and currently there are 126 records): var layout = { "2":[{"id":"40","attribute_id":"2","option_id":null,"design_attribute_id":"4","design_option_id":"131","width":"10","height":"10", "repeat":"0","top":"0","left":"0","bottom":"0","right":"0","use_right":"0","use_bottom":"0","apply_to_options":"0"}, {"id":"41","attribute_id":"2","option_id":"115","design_attribute_id":"4","design_option_id":"131","width":"2","height":"1", "repeat":"0","top":"0","left":"0","bottom":"4","right":"2","use_right":"0","use_bottom":"0","apply_to_options":"0"}, {"id":"44","attribute_id":"2","option_id":"118","design_attribute_id":"4","design_option_id":"131","width":"10","height":"10", "repeat":"0","top":"0","left":"0","bottom":"0","right":"0","use_right":"0","use_bottom":"0","apply_to_options":"0"}], "5":[{"id":"326","attribute_id":"5","option_id":null,"design_attribute_id":"4","design_option_id":"154","width":"5","height":"5", "repeat":"0","top":"0","left":"0","bottom":"0","right":"0","use_right":"0","use_bottom":"0","apply_to_options":"0"}] }; I need to match the right combination of values. Here's the function I currently use: function drawOption(attid, optid) { var attlayout = layout[attid]; $.each(attlayout, function(k, v) { // d_opt_id and d_opt_id are global scoped variable set elsewhere if (v.design_attribute_id == d_att_id && v.design_option_id == d_opt_id && v.attribute_id == attid && ((v.apply_to_options == 1 || (v.option_id === optid)))) { // Do stuff here } }); } The issue is that I might iterate through 10-15 layouts (unique attid's), and any given layout (attid) might have as many as 50 possibilities, which means that this loop is being run A LOT. Given the multiple criteria that have to be matched, would an AJAX call work better? (This JSON is dynamically created via PHP, so I could craft a PHP function that could possibly do this more efficently), or am I completely missing something about how to find items in a JSON object? As always, any suggestions for improving the code are welcome! EDIT: I apologize for not making this clear, but the purpose of this question is to find a way to improve the performance. The page has a lot of javascript, and this is a location where I know that performance is lower than it could be.

  Read the article

• MySQL Paritioning performance

  - by Imran Pathan

  Measured performance on key partitioned tables and normal tables separately. But we couldn't find any performance improvement with partitioning. Queries are pruned. Using MySQL 5.1.47 on RHEL 4. Table details: UserUsage - Will have entries for user mobile number and data usage for each date. Mobile number and Date as PRI KEY. UserProfile - Queries prev table and stores summary for each mobile number. Mobile number PRI KEY. CREATE TABLE `UserUsage` ( `Msisdn` decimal(20,0) NOT NULL, `Date` date NOT NULL, . . PRIMARY KEY USING BTREE (`Msisdn`,`Date`) ) ENGINE=InnoDB DEFAULT CHARSET=latin1 PARTITION BY KEY(Msisdn) PARTITIONS 50; CREATE TABLE `UserProfile` ( `Msisdn` decimal(20,0) NOT NULL, . . PRIMARY KEY (`Msisdn`) ) ENGINE=InnoDB DEFAULT CHARSET=latin1 PARTITION BY KEY(Msisdn) PARTITIONS 50; Second table is updated by query select and order by date in first table in a perl program, query is select * from UserUsage where Msisdn=number order by Date desc limit 7 [Process data in perl] update UserProfile values(....) where Msisdn=number explain partition for select, shows row being scanned in a particular partition only. Is something wrong with partition design or queries as partitioning is taking almost same or more time compared to normal tables?

  Read the article

< Previous Page | 98 99 100 101 102 103 104 105 106 107 108 109  | Next Page >