Search Results

Search found 8056 results on 323 pages for 'external'.

Page 102/323 | < Previous Page | 98 99 100 101 102 103 104 105 106 107 108 109  | Next Page >

  • cannot move file: "file cannot be found" (Windows XP)

    - by Steve
    I have some CR2 files in a subfolder of My Documents called My Photos on a Windows XP PC. I want to move them across a WIFI network to an external HDD attached to a Windows 7 PC. I have read/write permissions on the external HDD, as I mapped to this HDD using the Windows 7 user account. When I try to move a single CR2 file, I receive "Cannot copy IMG_3317: Cannot find the specified file. Make sure you specify the correct path and file name." If I refresh the source folder, the file is still there. It is not read only, and I have read/write access to the source file. I can view its properties. Why can't I move this file? I have been able to move similar files in the past.

    Read the article

  • 5v PCI to PCI-X or PCIe adapter?

    - by SiegeX
    We unfortunately have a very expensive ($10K) full-length 5 volt PCI card that we would like to use in the same system as another expensive PCI-X card. As luck would have it, it seems that PCI-X is not backwards compatible with 5v PCI cards. It would be a real shame to have to order a whole new server just to accommodate these two cards together. Does there exist any internal converter/adapter that will allow one to place a full-length 5v PCI card into either a PCI-X or PCIe slot? I've found an external expansion box that suits our needs but it's 1) External and 2) $1100. The only internal adapters I've been able to find go from Low-profile PCI - PCIe; nothing that seems to support full-height, full-length PCI cards.

    Read the article

  • OpenVPN - Ubunut 10.04 - Client Can't Connect to Server - Linux Route Add Command Failed

    - by nicorellius
    I suppose this could be asked on Server Fault as well, but it is specific to the client so I thought I'd start here. I have keys for a OpenVPN server already in place. I have used these keys to connect already, but using a Windows XP machine. I started by building the client.conf file so that I could run: sudo openvpn --config client.conf And it seems correct but I still can't connect and get these errors and lines of output: Mon May 31 14:34:57 2010 ERROR: Linux route add command failed: external program exited with error status: 7 Mon May 31 14:34:57 2010 /sbin/route add -net 10.8.0.1 netmask 255.255.255.255 gw 10.8.0.17 SIOCADDRT: File exists Mon May 31 14:34:57 2010 ERROR: Linux route add command failed: external program exited with error status: 7 Mon May 31 14:34:57 2010 Initialization Sequence Completed I searched the net for forums and ideas and tried some file moving and renaming but still ended up in the same place.

    Read the article

  • Problems setting up home web server

    - by putmatrix
    Has anyone been able to get a server working with the router smcwbr14t-g? Although I have been able to get Apache set up correctly and my website works on the internal IP 192.168.2.101, I've been running into a dead end when trying to get it to show up on my external IP. In my router, there is no option for port forwarding, but there are options for a 'virtual server'. Following the manual, I have it set up like this: http://imgur.com/zrcV7.png I also disabled the firewall. I configured Apache to listen to ports 80, 81, and 443, none of which solved the problem. However, the IP's 192.168.2.101:443 and :81 load fine. The problem is that I still cannot load the web site from my external IP, either from my computer or outside.

    Read the article

  • ISP Load Balancing with ISA 2006

    - by Bill Best
    I understand that ISA 2006 has an integrated Network Load Balancing feature. We also recently acquired a second internet line through a second service provider. I know it is possible to purchase a NLB router for using both incoming lines but this is not the route we would like to take if at all possible. Thus, is it possible to have two ISA 2006 servers each with there own external connection, Load balanced to be viewed as one gateway? My thought was to have two ISA servers each with three NICs, one external, one internal and one for cross communication. I am under the impression that this should work but was hoping someone else has had experience with it.

    Read the article

  • Using 2-port LSI 2308-8e card to control 24 SAS HDDs

    - by GregC
    I would like to rely on a RAID-on-chip solution to control 24 SAS hard drives in a direct-attached environment. How would you approach this to get best bandwidth given that I'd like to spend less than $10,000 on the interconnect. I've read that LSI 2308 chip can easily handle 8-drive SSD RAID6 in hardware. I'd like to harness its power to control 24 SAS hard drives over an expander in an external enclosure. Currently I use an Infortrend S24S-G2240 external enclosure. It provides its own controller and expander. I'd like to use LSI 2308 controller for RAID6 somehow instead of the mystery controller in the enclosure. P.S. I tried to create SAS-expander as a tag, but my rep on this site is low.

    Read the article

  • PowerShell fomat.ps1xml not reachable

    - by blsub6
    I'm trying to load Exchange Management Shell and it gives me a big 'ol red error that says: Import-Module : There were errors in loading the format data file: Microsoft.PowerShell, , %APPDATA%\Roaming\Microsoft\Exchange\RemotePowerShell\DOMAINNAME.format.ps1xml : File skipped because of the following validation exception: File %APPDATA%\Roaming\Microsoft\Exchange\RemotePowerShell\DOMAINNAME.format.ps1xml cannot be loaded. The file %APPDATA%\Roaming\Microsoft\ExchangeRemotePowerShell\DOMAINNAME\DOMAINNAME.format.ps1xml is not digitally signed. The script will not execute on the system. Please see "get-help about_signing" for more details... The %APPDATA% is stored on an external server on my network (that I can ping to without problems). I am missing a ton of PS cmdlets too, which I'm presuming are stored in '*.format.ps1xml' I tried finding the directory in which format.ps1xml is supposed to reside on the external server and it's not even created. Can someone tell me where to start?

    Read the article

  • Time Capsule Refuses to Connect After Interrupted File Transfer

    - by Steve Stifler
    I have a first generation Apple Time Capsule set up as a NAS on my network. I use the built-in hard drive for Time Machine backups, with a 1.5 TB external HDD attached to the Time Capsule over USB. Whenever I cancel a file transfer from the external drive to my Macbook (or quit a video I had been streaming from it, as was the most recent incident), I can no longer connect to the Time Capsule or the attached drive, and I have to unplug it to get it working again. How can I fix this? Is it a network error? Could the Time Capsule be at fault or could it be my computer?

    Read the article

  • Windows server's HDD Spin down daily/nightly - Does it makes sense?

    - by Riccardo
    A Windows Server 2003 R2 has the following hard disk configuration: - 3 internal hard disks attached to a 3Ware unit, configured in Raid 1 + spare unit - 3 external USB backup disks: 2 Verbatim 1TB (Samsung HD103SI) + 1 Western Digital 1TB (WD10EADS) The server runs 365 days per year, h24, however: - at daytime the server/user usage is limited to the internal hard disks - at nighttime there's no user usage, apart from scheduled maintenance tasks, basically the Server will be idle from 7PM to 8AM. apart from nighly backups (few hours). I was wondering if: (a) it makes any sense let Windows manage power savings, allowing disks to spin down accordingly, ** OR** let the disks stay awlays-on, to avoid permature wearing, due to continuous spin up/down (b) leave internal disks always on, and force external disks to power down while idle (this requires third party tools, such as Verbatim's Green button utility) Your thoughts?

    Read the article

  • CARP: two machines think they're the master, but only on one interface

    - by Conor McDermottroe
    I have two machines, each configured identically as a firewall/load balancer for a busy website. I have set them up with CARP and pfsync on both the internal and external interfaces. The internal interface is behaving as expected (primary listed as MASTER and secondary listed as BACKUP) On both machines, the network interfaces are as follows: em0 - External interface bge0 - Internal interface bge1 - Crossover connection between both machines carp0 - Shared external interface for CARP carp1 - Shared internal interface for CARP I've rewritten the IP addresses and MAC addresses below. The networks are as follows: 10.0.1.0/24 - External network 10.0.2.0/24 - Internal network 10.0.3.0/24 - Crossover network Here's the output from ifconfig on the primary: em0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=19b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4> ether [SNIP] inet 10.0.1.10 netmask 0xffffff00 broadcast 10.0.1.255 media: Ethernet 100baseTX <full-duplex> status: active bge0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM> ether [SNIP] inet 10.0.2.10 netmask 0xffffff00 broadcast 10.0.2.255 media: Ethernet 1000baseT <full-duplex> status: active bge1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM> ether [SNIP] inet 10.0.3.10 netmask 0xffffff00 broadcast 10.0.3.255 media: Ethernet 1000baseT <full-duplex> status: active lo0: flags=80c9<UP,LOOPBACK,RUNNING,NOARP,MULTICAST> metric 0 mtu 16384 options=3<RXCSUM,TXCSUM> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4 inet6 ::1 prefixlen 128 inet 127.0.0.1 netmask 0xff000000 pflog0: flags=141<UP,RUNNING,PROMISC> metric 0 mtu 33152 pfsync0: flags=0<> metric 0 mtu 1460 pfsync: syncdev: bge1 syncpeer: 10.0.3.11 maxupd: 128 carp0: flags=49<UP,LOOPBACK,RUNNING> metric 0 mtu 1500 inet 10.0.1.5 netmask 0xffffff00 carp: MASTER vhid 1 advbase 1 advskew 0 carp1: flags=49<UP,LOOPBACK,RUNNING> metric 0 mtu 1500 inet 10.0.2.5 netmask 0xffffff00 carp: MASTER vhid 2 advbase 1 advskew 0 And here's the /etc/rc.conf excerpt from the primary: defaultrouter="10.0.1.1" network_interfaces="em0 bge0 bge1 lo0 pfsync0" cloned_interfaces="carp0 carp1" ifconfig_em0="inet 10.0.1.10 netmask 255.255.255.0 media 100BaseTX mediaopt full-duplex" ifconfig_bge0="inet 10.0.2.10 netmask 255.255.255.0 media 1000BaseTX mediaopt full-duplex" ifconfig_bge1="inet 10.0.3.10 netmask 255.255.255.0 media 1000BaseTX mediaopt full-duplex" ifconfig_carp0="vhid 1 pass [SNIP] 10.0.1.5/24" ifconfig_carp1="vhid 2 pass [SNIP] 10.0.2.5/24" pfsync_enable="YES" pfsync_syncdev="bge1" pfsync_syncpeer="10.0.3.11" And here's the output on the secondary: em0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=19b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,TSO4> ether [SNIP] inet 10.0.1.11 netmask 0xffffff00 broadcast 10.0.1.255 media: Ethernet 100baseTX <full-duplex> status: active bge0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM> ether [SNIP] inet 10.0.2.11 netmask 0xffffff00 broadcast 10.0.2.255 media: Ethernet 1000baseT <full-duplex> status: active bge1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=9b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM> ether [SNIP] inet 10.0.3.11 netmask 0xffffff00 broadcast 10.0.3.255 media: Ethernet 1000baseT <full-duplex> status: active lo0: flags=80c9<UP,LOOPBACK,RUNNING,NOARP,MULTICAST> metric 0 mtu 16384 options=3<RXCSUM,TXCSUM> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4 inet6 ::1 prefixlen 128 inet 127.0.0.1 netmask 0xff000000 pflog0: flags=141<UP,RUNNING,PROMISC> metric 0 mtu 33152 pfsync0: flags=0<> metric 0 mtu 1460 pfsync: syncdev: bge1 syncpeer: 10.0.3.10 maxupd: 128 carp0: flags=49<UP,LOOPBACK,RUNNING> metric 0 mtu 1500 inet 10.0.1.5 netmask 0xffffff00 carp: MASTER vhid 1 advbase 1 advskew 20 carp1: flags=49<UP,LOOPBACK,RUNNING> metric 0 mtu 1500 inet 10.0.2.5 netmask 0xffffff00 carp: BACKUP vhid 2 advbase 1 advskew 20 And here's the /etc/rc.conf excerpt from the secondary: defaultrouter="10.0.1.1" network_interfaces="em0 bge0 bge1 lo0 pfsync0" cloned_interfaces="carp0 carp1" ifconfig_em0="inet 10.0.1.11 netmask 255.255.255.0 media 100BaseTX mediaopt full-duplex" ifconfig_bge0="inet 10.0.2.11 netmask 255.255.255.0 media 1000BaseTX mediaopt full-duplex" ifconfig_bge1="inet 10.0.3.11 netmask 255.255.255.0 media 1000BaseTX mediaopt full-duplex" ifconfig_carp0="vhid 1 pass [SNIP] advskew 20 10.0.1.5/24" ifconfig_carp1="vhid 2 pass [SNIP] advskew 20 10.0.2.5/24" pfsync_enable="YES" pfsync_syncdev="bge1" pfsync_syncpeer="10.0.3.10" What I don't understand is, the carp status on carp0 is MASTER on both machines when the status on carp1 is as it should be (MASTER on the primary and BACKUP on the secondary). What am I missing? Where should I be looking for clues?

    Read the article

  • Netinstalling CentOS if the gateway is in a different subnet

    - by James Lawrie
    I have a KVM host (A) running a virtual machine (B). They each have their own external IP address and the networking is setup using bridging between eth0 and br0 on A. B uses eth0, with A being the gateway. The problem is that the two external IP addresses are on different subnets (different /8s in fact) so by default, B claims it cannot reach A (Network Unreachable). I can resolve this by adding a static route on B: echo "any host gateway_ip dev eth0" > /etc/sysconfig/static-routes Modifying /etc/init.d/networking to reload the gateway after applying static routes (I only added the final line before fi): if [ -f /etc/sysconfig/static-routes ]; then grep "^any" /etc/sysconfig/static-routes | while read ignore args ; do /sbin/route add -$args done route add default gw "${GATEWAY}" fi If I then restart networking, it comes online. How can I do this (or work around it some other way) prior to the system being installed, ideally inside an Anaconda kickstart file?

    Read the article

  • Data Recovery needed with a Sector Zero problem on a HDD

    - by Jay Robins
    Left my computer (running XP) copying files to an external drive. Came back a few hours later, and the laptop was pretty hot and had frozen (Ironic aint it). Forced a reboot, and the laptop HDD hasnt worked since. Set it up in an external enclosure, but XP cant mount the HDD to a drive letter, but is able to recognize the manufacturer and drive size (Hitachi-320GB). No noise or rattling when the drive is spinning, but I cant get anything off of it, since i cant mount it, or see much of anything. Computer repair shop ran some software tests and says it came back with a "Zero Sector bad" message, and need to send it to a professional data recovery service. Any other options or ideas, before I have to spend thousands of dollars to recover my data? Any help would be GREATLY appreciated!!! I'm desperate and a poor student! Thanks in Advance, -Jay

    Read the article

  • Unable to access Citrix XenApp 6 published applications externally

    - by Christopher McCann
    We are trying to use a trial of Citrix XenApp 6 Fundamentals to virtualise a couple of applications as a proof of concept. We haven't ever used it before so I confess to be a noob with it. We can connect to the XenApp web interface, and the iPad app will connect and list the applications, but the applications themselves will not load. I discovered in the .ica file that it was attempting to connect to the internal IP address of the server instead of its static external. I have been following various threads on Citrix but nothing seems to have fixed it for me. The server is deployed on an EC2 instance with a static elastic IP. All the ports are opened and I can telnet into the XenApp server on 1493 and I get the ICA response. I have also run on ALTADDR and provided the external IP address. Does anyone have any ideas?

    Read the article

  • Does Exchange 2010 lift the restriction that DL addresses must be in Active Directory?

    - by Justin Grant
    We'd like to enable end-users to be able to create and maintain their own email distribution lists in Exchange 2010, where those lists may include users inside the company but also customers, partners, etc. who are outside the company. One of the limitations in Exchange 2007 (see this question) was that any member of a DL had to have an entry in active directory. You couldn't just take a group of email addresses (both inside and outside my company) and create an Exchange DL with those addresses without involving Active Directory admins to create entries for each external user. For a company creating hundreds of small mailing lists every month, this was an unacceptable IT expense. So we had to use a separate mailing list solution (GNU mailman) for DLs which included external users. Is this limitation relaxed in Exchange 2010 so we can throw away GNU mailman and use Exchange instead?

    Read the article

  • How can I mitigate DNS Server outages?

    - by Eric Belair
    Let's say I have a root domain of "mysite.com". That domain and its sub-domains have DNS served by an external service - let's call them Setwork Nolutions. If this external company is hit with a DDoS attack, my interally-hosted websites under this domain are no longer accessible at "mysite.com" or "*.mysite.com", even though the website(s) is/are fully up and operational. How can I mitigate such a problem so as to keep end users happy? The only solution others at my company have come up with is to create a second domain - i.e. "mysite2.com", and host its DNS at another company, and then communicate to all end users that this is the website they should use. I think this is ridiculous, and just leads to a bunch of other problems. I'd like to find a solution where we can point to the same website with the same URL without the original DNS host being operational. Any thoughts?

    Read the article

  • 3CX behind UT7.1 using a callcentric.com SIP account

    - by Corey
    Has anyone had any luck with getting 3CX working behind UT7.1 with a SIP account from callcentric.com? I am willing to reset my current UT box back to defaults, and start from there. I have a static public IP assigned to the external interface. My internal addressing is 192.168.76.0 . My 3CX box has 192.168.76.17 . Would anyone be willing to give me a step by step of changes to make in UT / 3CX. I currently have my UT box unplugged, and have replaced it with a Linksys unit. I have port forwarding setup for… TCP/UDP 5060 to 192.168.76.17 UDP 9000-9049 to 192.168.76.17 … and everything works great. I also have additional external IPs available if that helps.

    Read the article

  • Acer Ferrari 3000 in portrait display mode

    - by Riri
    I have a Acer Ferrari 3000 noetbook that I like to connnect to a external dispaly and show it in portrait mode. The computer runs a ATI Radeon 9200 graphic chipset and I can't find the setting for portrait and start believe the graphics card actually doesn't support it? I've looked at the latest drivers and can see that this has changed. What are my options? Can I buy some sort of external graphics thingy or other possible solutions will get up votes! ;)

    Read the article

  • My Music Folder Appearing On Desktop

    - by Michael
    Hello, I use Windows 7 and have recently been encountering a problem with the My Music folder. I keep all my music on an external hard drive and use a third party program such as VLC to play albums. I also have a large list of single MP3s that I play in WinAmp. Neither of these cause any problem but whenever I play a song in the bundled Windows Media Player a new My Music shortcut appears on the desktop. WMP is my default player, I've tried changing it to other players but whenever I use WMP it still creates this shortcut. The My Music folder is empty as all music is stored on the external hard drive and I've set WMP to collate, store and retain no information about anything, so I don't think it's anything to do with playlist history or anything. Any ideas what might be happening? Any help in solving this annoyance is appreciated.

    Read the article

  • What are the strategies available to minimise badblocks on an encrypted partition?

    - by David Andreoletti
    Let me explain my backup strategy and the problem I am facing. My current backup strategy: Open encrypted container and execute Carbon Copy Cleaner on it at least once a week. Rotate backup disks. Problem: I have an Truecrypt partition on my 1st external hard disk. I recently found out that some files on this encrypted partition cannot be read due to bad blocks (reported by Antonio Diaz's GNU 'ddrescue'). My backup strategy is ineffective in this scenario because bad blocks are discovered during backup. Possible strategy Strategy #0: Have the encrypted partition over a RAID 1 with 2 disks. Is this a suitable strategy ? Strategy #1: Do you think of any other one ? Environment: Mac OS X 10.8 External 2.5" hard disk (SATA) No RAID

    Read the article

  • How do I setup unison to sync a folder one way

    - by Rob
    I have a 1tb NAS that has a 1tb usb external hard attached I have prepared the file system on the usb disk and mounted it I want to 100% sync my data from my nas to the usb disk - but I want it to be incremental and only have the NAS as the 'master' - eg if a file changes on the usb external hard drive I want it to ignore this change as its not the live version (not that I think the files will change on the usb disk but im paranoid the live could get overwritten) Also if a file gets deleted on live I want to retain the deleted file on the usb disk Can unison sync one-way and achive the above for me? if so with simply unison sorce/ target/ Work? Thanks Rob

    Read the article

  • Oracle RAC interconnect in a Dell M1000e Blade Enclosure

    - by Antitribu
    We are looking at a Dell M1000e enclosure and appropriate Blades with 4 NICs each. We are planning on running Linux/Oracle 11g RAC on two blades, storage will be handled on an iSCSI SAN for which two NICs (via passthrough) will be connected leaving us with two NICs (via blade centre switches). We would like to have an interconnect (obviously) , an external IP and an internal IP. Would best practice be to: bond the remaining two interfaces and VLAN as appropriate to provide three virtual interfaces? run the interconnect on one interface and VLAN the external/internal interfaces? purchase a blade with more NICs as the above is a terrible idea? Another option? Please feel free to point out the blindingly obvious or to relevant documentation on support.oracle. I am specifically interested in supported configurations and best practices. Thanks!

    Read the article

  • I need a server or service that reroutes DNS requests

    - by Relentim
    We have two external servers, Dev and Prod. We are a software house and in the code we have a subdomain metrics.company.com that points to Prod. Development is continuous and our internal and external developers and testers will need to switch from Dev to Prod and back again. It is not an option to have a different sub domain in the code during development and change this for production. The way we wish to switch between Dev and Prod is to use DNS. We need a public DNS server that behaves normally apart from routing metrics.company.com to Dev. The users will be able to swap their DNS back and forward to hit the different servers. What is the easiest way to do this? Is there a company that hosts this service or am I going to have to rent a server and set it up myself? Any help would be much appreciated.

    Read the article

  • NLB RPC server is unavailable on the specified computer

    - by Robin Weston
    Hi guys, Firstly, I'll admit that my networking knowledge is limited so as people request more information I'll update this question accordingly. I am trying to create a NLB Cluster across 2 Windows Server 2008 Web Servers. Neither of the machines are members of a domain, and both have 2 NICs (one for processing external web traffic, and one for communicating internally). I have installed NLB on both machines, and have created a cluster on Host A and added itself to it. However, when I try and add Host B (using the address from the external NIC) I get the following error : "The RPC server is unavailable on the specified computer". On Host B I can see that the RPC service is running fine. I can also ping and RDP from Host A to Host B with no problems either. I have disabled the windows firewall on both machines but that had no effect

    Read the article

  • cannot connect to MS FTP 7.5 on Windows 2008 on Amazon EC2 instance

    - by minerj
    I have just installed the MS FTP 7.5 upgrade on my Windows 2008 Server (Service Pack 2) running on an Amazon EC2 instance. In the FTP Firewall Support settings for the server in IIS Manager I have set up the passive port range 45001 - 45005 and also set the External Firewall IP address to match the assigned Amazon Elastic IP address. Using the AWS Console I changed the Security Group for the server to allow access to the server through ports 21 and 45001 through 45005. Using an FTP client (either the command line FTP client or Windows Explorer) on the Amazon server I can connect to the FTP server but I cannot connect with an external FTP client. When I checked to see which ports were open on the server using Shields Up it shows that port 21 is open but ports 45001 to 45005 are closed. I assume I'm missing something. Any help greatly appreciated.

    Read the article

< Previous Page | 98 99 100 101 102 103 104 105 106 107 108 109  | Next Page >