Search Results

Search found 2602 results on 105 pages for 'dell vostro'.

Page 103/105 | < Previous Page | 99 100 101 102 103 104 105  | Next Page >

  • ESXI guests not using available CPU resources

    - by Alan M
    I have a VMWare ESXI 5.0.0 (it's a bit old, I know) host with three guest VMs on it. For reasons unknown, the guests will not use much of the availble CPU resources. I have all three guests in a single pool, with the hosts all configured to use the same amount of resource shares, so they're basically 33% each. The three guests are basically identically configured as far as their VM resources go. So the problem is, even when the guests are performing what should be very 'busy' activitites, such as at bootup, the actual host CPU consumed is something tiny, like 33mhz, when seen via vSphere console's "Virtual Machines" tab when viewing properties for the pool. And of course, the performance of the guest VMs is terrible. The host has plenty of CPU to spare. I've tried tinkering with individual guest VM resource settings; cranking up the reservation, etc. No matter. The guests just refuse to make use of the abundant CPU available to them, and insist on using a sliver of the available resources. Any suggestions? Update after reading various comments below Per the suggestions below, I did remove the guests from the application pool; this didn't make any difference. I do understand that the guests are not going to consume resources they do not need. I have tried to do a remote perfmon on the guest which is experiencing long boot times, but I cannot connect to the guest remotely with perfmon (guest is w2k8r2 server). Host graphs for CPU, Mem, Disk are basically flatlining; very little demand. Same is true for the guest stats; while the guest itself seems to be crawling, the guest resource graphing shows very little activity across CPU, Mem, Disk. Host is a Dell PowerEdge 2900, has 2 physical CPU,20gb RAM. (it's a test/dev environment using surplus gear) Guest1 has: VM ver. 7, 2vCPU, 4gb RAM, 140gb storage which lives on a RAID-5 array on the host. Guest2 has: VM ver. 7, 2vCPU, 4gb RAM, 140gb storage which lives on a RAID-5 array on the host. Guest3 has: VM ver. 7, 1vCPU, 2gb RAM, 2tb storage which lives on a RAID-5 ISCSI NAS box Perhaps I am making a false assumption that if a guest has a demand for CPU (e.g. Windows Task Manager shows 100% CPU), the host would supply the guest with more CPU (mem, disk) on demand. Another Update After checking the stats, it would appear that the host is indeed not busy at all, neither is the guest. I believe I have a good idea on the issue, though; a messed-up VMWare Tools install. The guest has VMware Tools on it, but the host says it does not. VMWare Tools refuses to uninstall, refuses to be upgraded, refuses to be recognized. While I cannot say with authority, this would appear to be something worth investigation. I do not know the origin of the guest itself, nor the specifics on the original VMWare Tools install. Following various bits of googling, I did come up with a few suggestions that went nowhere. To that end, I was going to delete this question, but was prompted not to do so since so many folks answered. My suspicion right now is; the problem truly is the guest; the guest is not making a demand on the host, and as a natural result, the host is treating the guest accordingly. My Final Update I am 99% certain the guest VM had something fundamentally wrong with it re VMWare Tools. I created a clone of a different VM with a near-identical OS config, but a properly working install of VMWare tools. The guest runs just great, and takes up it's allotment of resources when it needs to; e.g. it eats up about 850mhz CPU during startup, then ticks down to idle once the guest OS is stable.

    Read the article

  • No device file for partition on logical volume (Linux LVM)

    - by Brian
    I created a logical volume (scandata) containing a single ext3 partition. It is the only logical volume in its volume group (case4t). Said volume group is comprised by 3 physical volumes, which are three primary partitions on a single block device (/dev/sdb). When I created it, I could mount the partition via the block device /dev/mapper/case4t-scandatap1. Since last reboot the aforementioned block device file has disappeared. It may be of note -- I'm not sure -- that my superior (a college professor) had prompted this reboot by running sudo chmod -R [his name] /usr/bin, which obliterated all suid in its path, preventing the both of us from sudo-ing. That issue has been (temporarily) rectified via this operation. Now I'll cut the chatter and get started with the terminal dumps: $ sudo pvs; sudo vgs; sudo lvs Logging initialised at Sat Jan 8 11:42:34 2011 Set umask to 0077 Scanning for physical volume names PV VG Fmt Attr PSize PFree /dev/sdb1 case4t lvm2 a- 819.32G 0 /dev/sdb2 case4t lvm2 a- 866.40G 0 /dev/sdb3 case4t lvm2 a- 47.09G 0 Wiping internal VG cache Logging initialised at Sat Jan 8 11:42:34 2011 Set umask to 0077 Finding all volume groups Finding volume group "case4t" VG #PV #LV #SN Attr VSize VFree case4t 3 1 0 wz--n- 1.69T 0 Wiping internal VG cache Logging initialised at Sat Jan 8 11:42:34 2011 Set umask to 0077 Finding all logical volumes LV VG Attr LSize Origin Snap% Move Log Copy% Convert scandata case4t -wi-a- 1.69T Wiping internal VG cache $ sudo vgchange -a y Logging initialised at Sat Jan 8 11:43:14 2011 Set umask to 0077 Finding all volume groups Finding volume group "case4t" 1 logical volume(s) in volume group "case4t" already active 1 existing logical volume(s) in volume group "case4t" monitored Found volume group "case4t" Activated logical volumes in volume group "case4t" 1 logical volume(s) in volume group "case4t" now active Wiping internal VG cache $ ls /dev | grep case4t case4t $ ls /dev/mapper case4t-scandata control $ sudo fdisk -l /dev/case4t/scandata Disk /dev/case4t/scandata: 1860.5 GB, 1860584865792 bytes 255 heads, 63 sectors/track, 226203 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x00049bf5 Device Boot Start End Blocks Id System /dev/case4t/scandata1 1 226203 1816975566 83 Linux $ sudo parted /dev/case4t/scandata print Model: Linux device-mapper (linear) (dm) Disk /dev/mapper/case4t-scandata: 1861GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 1861GB 1861GB primary ext3 $ sudo fdisk -l /dev/sdb Disk /dev/sdb: 1860.5 GB, 1860593254400 bytes 255 heads, 63 sectors/track, 226204 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x00000081 Device Boot Start End Blocks Id System /dev/sdb1 1 106955 859116006 83 Linux /dev/sdb2 113103 226204 908491815 83 Linux /dev/sdb3 106956 113102 49375777+ 83 Linux Partition table entries are not in disk order $ sudo parted /dev/sdb print Model: DELL PERC 6/i (scsi) Disk /dev/sdb: 1861GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 880GB 880GB primary reiserfs 3 880GB 930GB 50.6GB primary 2 930GB 1861GB 930GB primary I find it a bit strange that partition one above is said to be reiserfs, or if it matters -- it was previously reiserfs, but LVM recognizes it as a PV. To reiterate, neither /dev/mapper/case4t-scandatap1 (which I had used previously) nor /dev/case4t/scandata1 (as printed by fdisk) exists. And /dev/case4t/scandata (no partition number) cannot be mounted: $sudo mount -t ext3 /dev/case4t/scandata /mnt/new mount: wrong fs type, bad option, bad superblock on /dev/mapper/case4t-scandata, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so All I get on syslog is: [170059.538137] VFS: Can't find ext3 filesystem on dev dm-0. Thanks in advance for any help you can offer, Brian P.S. I am on Ubuntu GNU/Linux 2.6.28-11-server (Jaunty) (out of date, I know -- that's on the laundry list).

    Read the article

  • Python in command line runs the wrong version?

    - by Deflect
    I have several versions of Python installed on a Windows 7 computer. I want to run Python 2.7 by default, but for whatever reason, typing python in the command line runs Python version 2.4.5. I've tried adding C:\Python27 to my system path variable as per this question, and manually combed my path variable it to make sure Python 2.4.5 wasn't tossed in there by mistake, but that didn't fix the issue. I have to type in C:\Python27\python.exe every time I want to access the correct version of python I want. What other places can I check? How can I make the command line use the correct version of python? I also found this but it's not for windows. [EDIT] My path (separated by semicolons): C:\Program Files\Common Files\Microsoft Shared\Windows Live; C:\Program Files (x86)\Common Files\Microsoft Shared\Windows Live; C:\Windows\system32; C:\Windows; C:\Windows\System32\Wbem; C:\Windows\System32\WindowsPowerShell\v1.0\; C:\Program Files\Dell\DW WLAN Card\Driver; C:\Program Files (x86)\Common Files\Roxio Shared\DLLShared\; C:\Program Files (x86)\Windows Live\Shared; c:\Program Files (x86)\Microsoft SQL Server\100\Tools\Binn\; c:\Program Files\Microsoft SQL Server\100\Tools\Binn\; c:\Program Files\Microsoft SQL Server\100\DTS\Binn\; C:\Program Files\TortoiseGit\bin; C:\Program Files\Java\jdk1.6.0_26\bin; C:\Program Files\Java\jdk1.6.0_21 ; C:\Program Files\IVI Foundation\VISA\Win64\Bin\; C:\Program Files (x86)\IVI Foundation\VISA\WinNT\Bin\; C:\Program Files (x86)\IVI Foundation\VISA\WinNT\Bin; C:\Program Files\WPIJavaCV\OpenCV_2.2.0\bin; C:\Program Files (x86)\LilyPond\usr\bin; C:\Program Files\TortoiseSVN\bin; C:\Program Files (x86)\doxygen\bin; C:\Program Files (x86)\Graphviz 2.28\bin; C:\Users\Michael\bin\Misc\cppcheck\; C:\Program Files (x86)\Git\cmd; C:\Python27\python.exe; C:\Ruby192\bin; C:\Users\Michael\AppData\Roaming\cabal\bin; C:\Python27\; [EDIT 2] Running python spews this out: 'import site' failed; used -v for traceback Python 2.4.5 (#1, Jul 22 2011, 02:01:04) [GCC 4.1.1] on mingw32 Type "help", "copyright", "credits" or "license" for more information. >>> ...and running python --version (as suggested below) seems to be an unrecognized option. (I also tried running python -v, and it appears that Python 2.4 is trying to import libraries from C:\Python27\Lib, and failed due to a syntax error when it encountered a with statement, which was added in later version, I think) Also, I'm not sure if it's significant or not, but the above python version says something about GCC and mingw32, while running C:\python27\python.exe shows this: Python 2.7.2 (default, Jun 12 2011, 15:08:59) [MSC v.1500 32 bit (Intel)] on win32 Type "help", "copyright", "credits" or "license" for more information. >>>>

    Read the article

  • Install Intel USB 3.0 eXtensible Host Controller Driver for Windows Server 2008 R2 x64

    - by ffrugone
    According to Intel and Dell, by board is technically a 'desktop' board and they therefore do not support Intel USB 3.0 eXtensible Host Controller drivers for Windows Server 2008 (R2 x64). I'm trying to find a workaround. I found an entry on someone who tried to tackle this, but I can't make his fix work for me. Below, I have copied both his entry, and my reply. I'm a loyal stackoverflow user, and hopefully the people here at serverfault can help me: anyforumuser Re: GA-Z77X-UD5H USB3 Drivers not installing? « Reply #6 on: July 05, 2012, 04:12:59 am » Thanks to JoeMiner , his process for the network drivers gave me the clues to figure out to get the USB3 drivers working. I have got the intel USB3 drivers working at full speed in win server 2008r2 you have to edit the following file : 1. mup.xml in change the "Windows7" to "W2K8" 2. in setup.if2 under [groups] line starting with "HSCSDRIVER " change the "IsOS( ... )" entry to "IsOS(WIN2008_R2,WIN2008_R2_MAXSP)" inf files for all copy the content of the [Intel.NTAMD64.6.1] group to the [Intel.NTAMD64.6.2] group driver folders. here i am not entirely sure which is correct so there are some double up's. in the drivers folder copy the "Win7" folder to "win2008" , "win2008_r2" and "x64" ie your drivers folder should now contain the "win2008" , "win2008_r2" and "x64" folders and they contain contents of the win7 folder (the inf files should of already been fixed) Run install , It should install properly and work now. You will have to reboot If it doesn't work remove the intel usb3 controllers from device manager and get it to "scan for hardware changes" Good luck !!! benevida Re: GA-Z77X-UD5H Intel Network Drivers not installing? « Reply #7 on: August 13, 2012, 02:21:14 pm » Thank you anyforumuser! A process for getting this driver installed was exactly what I needed. However, I've hit a snag. I believe I've followed every step exactly as written, but I'm getting an error during installation. I get the message "One or more files that are required for installation are either missing or corrupted. Setup will exit." Behind the error, the 'Setup Progress' shows the current step as "Copying File: C:\Program Files (x86)\Intel\Intel(R) USB 3.0 eXtensible Host Controller Driver\Drivers\iusb3xhc.man". I've checked the installation files, and iusb3xhc.man seems to be a viable file in all of the Windows 2008 sub-directories of the Drivers folder. Therefore I don't see how the file could be missing and I doubt that it is corrupted, (although it does NOT exist in the \Drivers\HCSwitch folder). I opened 'Setup.if2', and there are two aspects to the step of copying iusb3xhc.man that caught my eye. First, the steps immediately preceding are set to 'error=ignore'. If they hadn't completed successfully, this is the first step where we'd hear about it. Second, this is the first step where the relative path '%source%\drivers\%_os%\%_ia%\' is used. If I haven't named the Windows 2008 sub-directories correctly, I could see where things are fouling up. In any event, if someone could take a look and make suggestions I'd appreciate it. Thank you.

    Read the article

  • Fix overscan in Linux with Intel graphics Vizio HDTV

    - by Padenton
    I am connecting my server to my HDTV so that I can conveniently display it there. My VIZIO HDTV cuts off all 4 edges. I already realize it is not optimal to be running a GUI on a server; this server will not have much external traffic so I prefer it for convenience. I have already spent countless hours searching for a fix, but all I could find required an ATI or NVIDIA graphics card, or didn’t work. In Windows, the Intel driver has a setting for underscan, though it seems only to be available by a glitch. Here’s my specs: Ubuntu Linux (Quantal 12.10) (Likely to switch to Arch) This is a home server computer, with KDE for managing(for now, at least) Graphics: Intel HD Graphics 4000 from Ivy Bridge Motherboard: ASRock Z77 Extreme4 CPU: Intel Core i5-3450 My monitors: Dell LCD monitor Vizio VX37L_HDTV10A 37" on HDMI input I have tried all of the following from both HDMI?HDMI and DVI?HDMI cables connected to the ports on my motherboard: Setting properties in xrandr Making sure drivers are all up to date Trying several different modes The TV was “cheap”; max resolution 1080i. I am able to get a 1920x1080 modeline, in both GNU/Linux and Windows, without difficulty. There is no setting in the menu to fix the overscan (I have tried all of them, I realize it’s not always called overscan). I have been in the service menu for the TV, which still does not contain an option to fix it. No aspect ratio settings, etc. The TV has a VGA connector but I am unsure if it would fix it, as I don’t have a VGA cable long enough, and am not sure it would get me the 1920x1080 resolution which I want. Using another resolution does not fix the problem. I tried custom modelines with the dimensions of my screen’s viewable area, but it wouldn’t let me use them. Ubuntu apparently doesn’t automatically generate an xorg.conf file for use. I read somewhere that modifying it may help solve it. I tried X -configure several times(with reboots, etc.) but it consistently gave the following error messages: In log file: … (WW) Falling back to old probe method for vesa Number of created screens does not match number of detected devices. Configuration failed. In output: … (++) Using config file: "/root/xorg.conf.new" (==) Using system config directory "/usr/share/X11/xorg.conf.d" Number of created screens does not match number of detected devices. Configuration failed. Server terminated with error (2). Closing log file. Tried using 'overscan' prop in xrandr: root@xxx:/home/xxx# xrandr --output HDMI1 --set overscan off X Error of failed request: BadName (named color or font does not exist) Major opcode of failed request: 140 (RANDR) Minor opcode of failed request: 11 (RRQueryOutputProperty) Serial number of failed request: 42 Current serial number in output stream: 42 'overscan on', 'underscan off', 'underscan on' were all also tried. Originally tried with Ubuntu 12.04, but failed and so updated to 12.10 when it was released. All software is up to date. I am not opposed to reinstalling my OS, likely will anyways (my preference being Arch).

    Read the article

  • compile lastest bnx2 driver on debian squeeze

    - by markus
    I want to upgrade the bnx2 network card driver in a Dell Power Edge R410. I downloaded the latest driver version from the broadcom website. If I want to compile the driver it fails with the following errors: make make -C bnx2/src KVER=2.6.32-5-amd64 PREFIX= make[1]: Entering directory `/tmp/netxtreme2-6.2.23/bnx2-2.0.23b/src' make -C /lib/modules/2.6.32-5-amd64/build SUBDIRS=/tmp/netxtreme2-6.2.23/bnx2-2.0.23b/src modules make[2]: Entering directory `/usr/src/linux-headers-2.6.32-5-amd64' Building modules, stage 2. MODPOST 2 modules make[2]: Leaving directory `/usr/src/linux-headers-2.6.32-5-amd64' make[1]: Leaving directory `/tmp/netxtreme2-6.2.23/bnx2-2.0.23b/src' make -C bnx2x/src KVER=2.6.32-5-amd64 PREFIX= make[1]: Entering directory `/tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src' make -C /lib/modules/2.6.32-5-amd64/build M=`pwd` modules make[2]: Entering directory `/usr/src/linux-headers-2.6.32-5-amd64' CC [M] /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.o In file included from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x.h:68, from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.c:80: /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_compat.h:1009:1: error: "PCI_VPD_LRDT_ID_STRING" redefined In file included from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.c:34: /usr/src/linux-headers-2.6.32-5-common/include/linux/pci.h:1327:1: error: this is the location of the previous definition In file included from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x.h:68, from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.c:80: /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_compat.h:1011:1: error: "PCI_VPD_LRDT_RO_DATA" redefined In file included from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.c:34: /usr/src/linux-headers-2.6.32-5-common/include/linux/pci.h:1328:1: error: this is the location of the previous definition In file included from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x.h:68, from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.c:80: /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_compat.h:1013:1: error: "PCI_VPD_LRDT_RW_DATA" redefined In file included from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.c:34: /usr/src/linux-headers-2.6.32-5-common/include/linux/pci.h:1329:1: error: this is the location of the previous definition In file included from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x.h:68, from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.c:80: /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_compat.h:1019:1: error: "PCI_VPD_SRDT_END" redefined In file included from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.c:34: /usr/src/linux-headers-2.6.32-5-common/include/linux/pci.h:1334:1: error: this is the location of the previous definition In file included from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x.h:68, from /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.c:80: /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_compat.h:1032: error: conflicting types for ‘pci_vpd_lrdt_size’ /usr/src/linux-headers-2.6.32-5-common/include/linux/pci.h:1355: error: previous definition of ‘pci_vpd_lrdt_size’ was here /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_compat.h:1037: error: conflicting types for ‘pci_vpd_srdt_size’ /usr/src/linux-headers-2.6.32-5-common/include/linux/pci.h:1366: error: previous definition of ‘pci_vpd_srdt_size’ was here /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_compat.h:1042: error: conflicting types for ‘pci_vpd_find_tag’ /usr/src/linux-headers-2.6.32-5-common/include/linux/pci.h:1391: error: previous declaration of ‘pci_vpd_find_tag’ was here /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_compat.h:1077: error: conflicting types for ‘pci_vpd_info_field_size’ /usr/src/linux-headers-2.6.32-5-common/include/linux/pci.h:1377: error: previous definition of ‘pci_vpd_info_field_size’ was here /tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_compat.h:1082: error: conflicting types for ‘pci_vpd_find_info_keyword’ /usr/src/linux-headers-2.6.32-5-common/include/linux/pci.h:1403: error: previous declaration of ‘pci_vpd_find_info_keyword’ was here make[5]: *** [/tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src/bnx2x_main.o] Fehler 1 make[4]: *** [_module_/tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src] Fehler 2 make[3]: *** [sub-make] Fehler 2 make[2]: *** [all] Fehler 2 make[2]: Leaving directory `/usr/src/linux-headers-2.6.32-5-amd64' make[1]: *** [bnx2x.o] Fehler 2 make[1]: Leaving directory `/tmp/netxtreme2-6.2.23/bnx2x-1.62.15/src' make: *** [l2build] Fehler 2

    Read the article

  • How to configure multiple iSCSI Portal Groups on a EqualLogic PS6100?

    - by kce
    I am working on a migration from a VMware vSphere environment to a Hyper-V Cluster utilizing Windows Server 2012 R2. The setup is pretty small, an EqualLogic PS6100e and two Dell PowerConnect 5424 switches and handful of R710s and R620s. The SAN was configured as a non-RFC1918 network that is not assigned to our organization and since I am working on building a new virtualization environment I figured that this would be an appropriate time to do a subnet migration. I configured a separate VLAN and subnet on the switches and the two previously unused NICs on the PS6100's controllers. At this time I only have a single Hyper-V host cabled in but I can successfully ping the PS6100 from the host. From the PS6100 I can ping each of the four NICs that currently on the storage network. I cannot connect the Microsoft iSCSI Initiator to the Target. I have successfully added the Target Portals (the IP addresses of PS6100 NICs) and the Targets are discovered but listed as inactive. If I try to Connect to them I get the following error, "Log onto Target - Connection Failed" and ISCSIPrt 1 and 70 events are recorded in the Event Log. I have verified that access control to the volume is not the problem by temporarily disabling it. I suspect the problem is with the Portal Group IP address which is still listed as Group Address of old subnet (I know, I know I might be committing the sin of the X/Y problem but everything else looks good): RFC3720 has this to say about Network Portal and Portal Groups: Network Portal: The Network Portal is a component of a Network Entity that has a TCP/IP network address and that may be used by an iSCSI Node within that Network Entity for the connection(s) within one of its iSCSI sessions. A Network Portal in an initiator is identified by its IP address. A Network Portal in a target is identified by its IP address and its listening TCP port. Portal Groups: iSCSI supports multiple connections within the same session; some implementations will have the ability to combine connections in a session across multiple Network Portals. A Portal Group defines a set of Network Portals within an iSCSI Network Entity that collectively supports the capability of coordinating a session with connections spanning these portals. Not all Network Portals within a Portal Group need participate in every session connected through that Portal Group. One or more Portal Groups may provide access to an iSCSI Node. Each Network Portal, as utilized by a given iSCSI Node, belongs to exactly one portal group within that node. The EqualLogic Group Manager documentation has this to say about the Group IP Address: You use the group IP address as the iSCSI discovery address when connecting initiators to iSCSI targets in the group. If you modify the group IP address, you might need to change your initiator configuration to use the new discovery address Changing the group IP address disconnects any iSCSI connections to the group and any administrators logged in to the group through the group IP address. Which sounds equivalent to me (I am following up with support to confirm). I think a reasonable explanation at this point is that the Initiator can't complete the connection to the Target because the Group IP Address / Network Portal is on a different subnet. I really want to avoid a cutover and would prefer to run both subnets side-by-side until I can install and configure each Hyper-V host. Question/s: Is my assessment at all reasonable? Is it possible to configure multiple Group IP Addresses on the EqualLogic PS6100? I don't want to just change it as it will disconnect the remaining ESXi hosts. Am I just Doing It Wrong(TM)?

    Read the article

  • Dual head setup for Ubuntu 10.04.1 and Windows XP Pro with same hardware configuration

    - by mejpark
    I have a Dell OptiPlex 360 workstation at work, with 2 x ATI RV280 [Radeon 9200 PRO] graphics cards installed, which are attached to two identical 19" HII flat panel monitors. I'm using the open source Radeon driver with Ubuntu, and the proprietary drivers with Windows. The good news is that dual head configuration works for both OSes. The bad news is, I have to use a different hardware configuration for each OS to achieve this. Hardware config #1: Dual monitors work for Windows XP Pro like this: First display -> external VGA port Second display -> DVI input on gfx card Hardware config #2: Dual monitors work for Ubuntu 10.04.1 like this: First display -> VGA port on gfx card Second display -> DVI input on gfx card I connected up the displays according to Config #2 and booted up Windows, which resulted in a mirror image on both screens. I was unable to login, as the login box was not visible. I unplugged the VGA lead from gfx card and plugged it into the external VGA port (Config #1) - Windows dual head works again, but the VGA-connected screen is not recognised by Ubuntu and remains in standby mode. Is it possible to configure a dual head setup for Ubuntu using Config #1, or am I missing something? I tried setting up dual monitors using Config #1, this morning which didn't work. By default, there is no xorg.conf file in Ubuntu 10.04.1, so I generated one using: $ sudo X :2 -configure X.Org X Server 1.7.6 Release Date: 2010-03-17 X Protocol Version 11, Revision 0 Build Operating System: Linux 2.6.24-27-server i686 Ubuntu Current Operating System: Linux harrier 2.6.32-24-generic #42-Ubuntu SMP Fri Aug 20 14:24:04 UTC 2010 i686 Kernel command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-24-generic root=UUID=a34c1931-98d4-4a34-880c-c227a2936c4a ro quiet splash Build Date: 21 July 2010 12:47:34PM xorg-server 2:1.7.6-2ubuntu7.3 (For technical support please see http://www.ubuntu.com/support) Current version of pixman: 0.16.4 Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.2.log", Time: Mon Sep 13 10:02:02 2010 List of video drivers: apm ark intel mach64 s3virge trident mga tseng ati nouveau neomagic i740 openchrome voodoo s3 i128 radeon siliconmotion nv ztv vmware v4l chips rendition savage sisusb tdfx geode sis r128 cirrus fbdev vesa (++) Using config file: "/home/michael/xorg.conf.new" (==) Using config directory: "/usr/lib/X11/xorg.conf.d" (II) [KMS] No DRICreatePCIBusID symbol, no kernel modesetting. Xorg detected your mouse at device /dev/input/mice. Please check your config if the mouse is still not operational, as by default Xorg tries to autodetect the protocol. Xorg has configured a multihead system, please check your config. Your xorg.conf file is /home/michael/xorg.conf.new To test the server, run 'X -config /home/michael/xorg.conf.new' ddxSigGiveUp: Closing log $ sudo X -config /home/michael/xorg.conf.new Fatal server error: Server is already active for display 0 If this server is no longer running, remove /tmp/.X0-lock and start again. Please consult the The X.Org Foundation support at http://wiki.x.org for help. ddxSigGiveUp: Closing log I then booted Ubuntu in failsafe mode, dropped into root shell, and executed $ X -config /home/michael/xorg.conf.new again. The screen went blank and turned off, so

    Read the article

  • Cheapest way to connect 20-24 Sata II HDDs in a budget storage server?

    - by Joe Hopfgartner
    I need to assemble a high density storage server for as cheap as possible. It's been a while for me and the last systems I integrated didn't even have Sata yet... During my Research I of course stumbled about Nexsan SATA Beast, the BackBlaze storage Pods as well as some ridiculously overpriced HP Proliant or Dell storage solutions. Finally I choose Norco cases as the way to go. My eye is set on the RPC-4020, which is a 4U 19" Rackmount case with 20 Hot Swap 3.5" SATA/SAS Hdd trays (Backplanes included) and room for two 2.5" OS drives as well as a Slim Line CD-Rom. The backplanes connect with a single SATA port for each drive, so there are 20 internal SATA ports to to be connected. They also have redundant power ports which I think is quite nice. The cheapest price I have found is 290$ + 40$ shipping. In europe the cheapest unfortunately is 370€ (500$) + 40 € shipping... A nice alternative would be the RPC-4224 which has SFF-8087 Mini SAS connectors that bundle 4 SATA trays each. But it doesn't seem to be available in Europe (where i am) anywhere. So here comes my problem: What Mainboard/Controller to choose to connect them for as cheap as possible while still having nice data rates? I have to say that the server is intended as a Storage server with 1gps connectivity and the data transfer will be distributed very evenly across all drives. I also don't require any raid functionality. This is all done at application level, I just need JBOD. So for example if I go for the RPC 4020 Model I need to connect 20 Storage + 1 OS + 1 CDROM Sata ports. I searched a bit and stumbled across this very low priced controller: http://www.intel.com/products/server/raid-controllers/SASWT4I/SASWT4I-overview.htm They sell it for 115 € here and the specs say it can control up to 122 hard discs and has 4 Mini SAS connectors. So I would use 4 Mini SAS 36pin - 4 SATA 7pin cables to connect 4 SATA drives to each port and choose a Mainboard taht has 6 SATA on board (for example this one) and hurray, I can connect my 22 SATA devices for as low as about ~ 220 EUR (cpu, ram, psu, case not counted) Question: WOULD THAT WORK? And if not, why? 2nd Question: If I go for the 4220 or 4224 Model, I have internal Mini SAS connectors. Am I right in assuming that the backplane than acts as a "SAS Expander"? And can I just plug these SAS connectors into any SAS port I can find on my controller / mainboard or are there certain requirements? I know that SATA port multipliers only work with controllers that are ready for that. But isn't this expansion already implemented in the SAS standard? I am sorry that this is a very broad question, but I really spent the last week reading up and it seems to be not so clear! Especially all the controlling hardware specifications! 3rd Question: A lot of hardware specs feature "internal channels" and "internal connectors". The connecors are the physical numbers of places where I can plug a cable in. I got that. But are the "internal channels" always the maximum numbers of physical drives that can be used in the end? Or can I enhance this further by Expanders/Fanouts? 4th and last question: What do you think about the setup so far? Do you know any good alternatives? Maby I am completely going the wrong way and some DAS would be way better? Are there any comparable chassis available in europe? Please feel free to say whatever you think is relevant to the subject!

    Read the article

  • How do i change the BIOS boot splash screen?

    - by YumYumYum
    I have a Dell PC which has very ugly and bad luck looking Alien face on every boot. I want to change it or disable it forever, but in Bios they do not have any options. How can i change this from my linux Fedora or ArchLinux which is running now? Tried following does not work. ( http://www.pixelbeat.org/docs/bios/ ) ./flashrom -r firmware.old #save current flash ROM just in case ./flashrom -wv firmware.new #write and verify new flash ROM image Also tried: $ cat c.c #include <stdio.h> #include <inttypes.h> #include <netinet/in.h> #include <stdlib.h> #include <string.h> #include <sys/types.h> #include <sys/stat.h> #include <fcntl.h> #include <unistd.h> #define lengthof(x) (sizeof(x)/sizeof(x[0])) uint16_t checksum(const uint8_t* data, int len) { uint16_t sum = 0; int i; for (i=0; i<len; i++) sum+=*(data+i); return htons(sum); } void usage(void) { fprintf(stderr,"Usage: therm_limit [0,50,53,56,60,63,66,70]\n"); fprintf(stderr,"Report therm limit of terminal in BIOS\n"); fprintf(stderr,"If temp specifed, it is changed if required.\n"); exit(EXIT_FAILURE); } #define CHKSUM_START 51 #define CHKSUM_END 109 #define THERM_OFFSET 67 #define THERM_SHIFT 0 #define THERM_MASK (0x7 << THERM_SHIFT) #define THERM_OFF 0 uint8_t thermal_limits[]={0,50,53,56,60,63,66,70}; #define THERM_MAX (lengthof(thermal_limits)-1) #define DEV_NVRAM "/dev/nvram" #define NVRAM_MAX 114 uint8_t nvram[NVRAM_MAX]; int main(int argc, char* argv[]) { int therm_request = -1; if (argc>2) usage(); if (argc==2) { if (*argv[1]=='-') usage(); therm_request=atoi(argv[1]); int i; for (i=0; i<lengthof(thermal_limits); i++) if (thermal_limits[i]==therm_request) break; if (i==lengthof(thermal_limits)) usage(); else therm_request=i; } int fd_nvram=open(DEV_NVRAM, O_RDWR); if (fd_nvram < 0) { fprintf(stderr,"Error opening %s [%m]\n", DEV_NVRAM); exit(EXIT_FAILURE); } if (read(fd_nvram, nvram, sizeof(nvram))==-1) { fprintf(stderr,"Error reading %s [%m]\n", DEV_NVRAM); close(fd_nvram); exit(EXIT_FAILURE); } uint16_t chksum = *(uint16_t*)(nvram+CHKSUM_END); printf("%04X\n",chksum); exit(0); if (chksum == checksum(nvram+CHKSUM_START, CHKSUM_END-CHKSUM_START)) { uint8_t therm_byte = *(uint16_t*)(nvram+THERM_OFFSET); uint8_t therm_status=(therm_byte & THERM_MASK) >> THERM_SHIFT; printf("Current thermal limit: %d°C\n", thermal_limits[therm_status]); if ( (therm_status == therm_request) ) therm_request=-1; if (therm_request != -1) { if (therm_status != therm_request) printf("Setting thermal limit to %d°C\n", thermal_limits[therm_request]); uint8_t new_therm_byte = (therm_byte & ~THERM_MASK) | (therm_request << THERM_SHIFT); *(uint8_t*)(nvram+THERM_OFFSET) = new_therm_byte; *(uint16_t*)(nvram+CHKSUM_END) = checksum(nvram+CHKSUM_START, CHKSUM_END-CHKSUM_START); (void) lseek(fd_nvram,0,SEEK_SET); if (write(fd_nvram, nvram, sizeof(nvram))!=sizeof(nvram)) { fprintf(stderr,"Error writing %s [%m]\n", DEV_NVRAM); close(fd_nvram); exit(EXIT_FAILURE); } } } else { fprintf(stderr,"checksum failed. Aborting\n"); close(fd_nvram); exit(EXIT_FAILURE); } return EXIT_SUCCESS; } $ gcc c.c -o bios # ./bios 16DB

    Read the article

  • bash: per-command history. How does it work?

    - by romainl
    OK. I have an old G5 running Leopard and a Dell running Ubuntu 10.04 at home and a MacPro also running Leopard at work. I use Terminal.app/bash a lot. On my home G5 it exhibits a nice feature: using ? to navigate history I get the last command starting with the few letters that I've typed. This is what I mean (| represents the caret): $ ssh user@server $ vim /some/file/just/to/populate/history $ ss| So, I've typed the two first letters of "ssh", hitting ? results in this: $ ssh user@server instead of this, which is the behaviour I get everywhere else : $ vim /some/file/just/to/populate/history If I keep on hitting ? or ?, I can navigate through the history of ssh like this: $ ssh otheruser@otherserver $ ssh user@server $ ssh yetanotheruser@yetanotherserver It works the same for any command like cat, vim or whatever. That's really cool. Except that I have no idea how to mimic this behaviour on my other machines. Here is my .profile: export PATH=/Developer/SDKs/flex_sdk_3.4/bin:/opt/local/bin:/opt/local/sbin:/usr/local/bin:/sw/bin:/sw/sbin:/bin:/sbin:/bin:/sbin:/usr/bin:/usr/sbin:$HOME/Applications/bin:/usr/X11R6/bin export MANPATH=/usr/local/share/man:/usr/local/man:opt/local/man:sw/share/man export INFO=/usr/local/share/info export PERL5LIB=/opt/local/lib/perl5 export PYTHONPATH=/opt/local/bin/python2.7 export EDITOR=/opt/local/bin/vim export VISUAL=/opt/local/bin/vim export JAVA_HOME=/System/Library/Frameworks/JavaVM.framework/Versions/1.6.0/Home export TERM=xterm-color export GREP_OPTIONS='--color=auto' GREP_COLOR='1;32' export CLICOLOR=1 export LS_COLORS='no=00:fi=00:di=01;34:ln=target:pi=40;33:so=01;35:do=01;35:bd=40;33;01:cd=40;33;01:or=40;31;01:*.tar=00;31:*.tgz=00;31:*.arj=00;31:*.taz=00;31:*.lzh=00;31:*.zip=00;31:*.z=00;31:*.Z=00;31:*.gz=00;31:*.bz2=00;31:*.deb=00;31:*.rpm=00;31:*.TAR=00;31:*.TGZ=00;31:*.ARJ=00;31:*.TAZ=00;31:*.LZH=00;31:*.ZIP=00;31:*.Z=00;31:*.Z=00;31:*.GZ=00;31:*.BZ2=00;31:*.DEB=00;31:*.RPM=00;31:*.jpg=00;35:*.png=00;35:*.gif=00;35:*.bmp=00;35:*.ppm=00;35:*.tga=00;35:*.xbm=00;35:*.xpm=00;35:*.tif=00;35:*.png=00;35:*.fli=00;35:*.gl=00;35:*.dl=00;35:*.psd=00;35:*.JPG=00;35:*.PNG=00;35:*.GIF=00;35:*.BMP=00;35:*.PPM=00;35:*.TGA=00;35:*.XBM=00;35:*.XPM=00;35:*.TIF=00;35:*.PNG=00;35:*.FLI=00;35:*.GL=00;35:*.DL=00;35:*.PSD=00;35:*.mpg=00;36:*.avi=00;36:*.mov=00;36:*.flv=00;36:*.divx=00;36:*.qt=00;36:*.mp4=00;36:*.m4v=00;36:*.MPG=00;36:*.AVI=00;36:*.MOV=00;36:*.FLV=00;36:*.DIVX=00;36:*.QT=00;36:*.MP4=00;36:*.M4V=00;36:*.txt=00;32:*.rtf=00;32:*.doc=00;32:*.odf=00;32:*.rtfd=00;32:*.html=00;32:*.css=00;32:*.js=00;32:*.php=00;32:*.xhtml=00;32:*.TXT=00;32:*.RTF=00;32:*.DOC=00;32:*.ODF=00;32:*.RTFD=00;32:*.HTML=00;32:*.CSS=00;32:*.JS=00;32:*.PHP=00;32:*.XHTML=00;32:' export LC_ALL=C export LANG=C stty cs8 -istrip -parenb bind 'set convert-meta off' bind 'set meta-flag on' bind 'set output-meta on' alias ip='curl http://www.whatismyip.org | pbcopy' alias ls='ls -FhLlGp' alias la='ls -AFhLlGp' alias couleurs='$HOME/Applications/bin/colors2.sh' alias td='$HOME/Applications/bin/todo.sh' alias scale='$HOME/Applications/bin/scale.sh' alias stree='$HOME/Applications/bin/tree' alias envoi='$HOME/Applications/bin/envoi.sh' alias unfoo='$HOME/Applications/bin/unfoo' alias up='cd ..' alias size='du -sh' alias lsvn='svn list -vR' alias jsc='/System/Library/Frameworks/JavaScriptCore.framework/Versions/A/Resources/jsc' alias asl='sudo rm -f /private/var/log/asl/*.asl' alias trace='tail -f $HOME/Library/Preferences/Macromedia/Flash\ Player/Logs/flashlog.txt' alias redis='redis-server /opt/local/etc/redis.conf' source /Users/johncoltrane/Applications/bin/git-completion.sh export GIT_PS1_SHOWUNTRACKEDFILES=1 export GIT_PS1_SHOWUPSTREAM="verbose git" export GIT_PS1_SHOWDIRTYSTATE=1 export PS1='\n\[\033[32m\]\w\[\033[0m\] $(__git_ps1 "[%s]")\n\[\033[1;31m\]\[\033[31m\]\u\[\033[0m\] $ \[\033[0m\]' mkcd () { mkdir -p "$*" cd "$*" } function cdl { cd $1 la } n() { $EDITOR ~/Dropbox/nv/"$*".txt } nls () { ls -c ~/Dropbox/nv/ | grep "$*" } copy(){ curl -s -F 'sprunge=<-' http://sprunge.us | pbcopy } if [ -f /opt/local/etc/profile.d/cdargs-bash.sh ]; then source /opt/local/etc/profile.d/cdargs-bash.sh fi if [ -f /opt/local/etc/bash_completion ]; then . /opt/local/etc/bash_completion fi Any idea?

    Read the article

  • md/raid:md2: cannot start dirty degraded array, kernel panic

    - by nl-x
    After having made use of a remote power switch, my server did not come back online. When I went to the datacenter and reboot the computer on the spot I see the server booting (I see the centos progress bar with running almost all the way to the end) and eventually giving the following messages: md/raid:md2: cannot start dirty degraded array. md/raid:md2: failed to run raid set. md: pers->run() failed ... md/raid:md2: cannot start dirty degraded array. md/raid:md2: failed to run raid set. md: pers->run() failed ... Kernel panic - not syncing: Attempted to kill init! Pid: 1, comm: init not tainted 2.6.32-279.1.1.el6.i686 #1 Call Trace: [<c083bfbc>] ? panic+0x68/0x11c [<c045a501>] ? do_exit+0x741/0x750 [<c045a54c>] ? do_group_exit+0x3c/0xa0 [<c045a5c1>] ? sys_exit_group+0x11/0x20 [<c083eba4>] ? syscall_call+0x7/0xb [<c083007b>] ? cmos_wake_setup+0x62/0x112 The server runs CentOS and has software raid, and I don't have backups of the raid settings. The only backup I have is of /home and the database dumps. (Glad to at least have those though.) Since the server is an old Dell PowerEdge 1750 with no CD-ROM drive, I have no way of booting the machine from a boot disk. I also remember in the past that the server also wouldn't boot from a bootable USB disk. So the only way I know how to boot the server is to go to the datacenter, pick up the server and take it to the office. Screw open the server. Attach a cdrom drive to an IDE slot on the motherboard. And then boot it. I am hoping you guys could help me avoid this. I have looked a bit through the boot options and I found the following boot options. When CentOS is about to boot and interrupt the boot-countdown: CentOS (2.6.32-279.1.1.el63.i686) CentOS Linux (2.6.32-71.29.1.el6.i686) centos (2.6.32-71.el6.i686) I think the first configuration is the default one, because choosing that gets me to the above mentioned kernel panic. The other ones end with something like "Sleeping forever". I can press 'e' to edit boot commands, press 'a' to modify kernel arguments and press 'c' for grub command line. The command line gives a grub prompt. But I have no idea how to get the system to boot without (trying to) access the dirty partitions. What I want to do is off course: - boot the machine - check hard drive for errors - mark the drive as clean

    Read the article

  • How do I reset/update my BIOS for Optiplex GX280?

    - by Sam Langlhey
    So far this has been a nightmare for me, which has been frustrating me constantly. I am using Dell Optiplex GX280 with Windows XP home edition, which is running a BIOS version A04. Recently, i've rebooted the pc to find out that its not booting. It will get to the Windows boot up screen with the progress bar but only to restart to the same process again, over and over. Frustrated that I am, i've inserted the Windows recovery CD to at least either repair of reinstall the operating system to find out that was not possible. I hit F8 to have the boot options, each of the boot option that I've selected gave me an error saying: "Selected boot device is not available." Right after that, I went to the BIOS setting and did a diagnostic test, which recognized all the Boot devices onboard. Now, I cannot even repair of reinstall Windows XP, because the system is not booting from none of the boot devices. The surprise is when I removed the hard-drive from the computer and loaded it on into another computer successfully; that's right, there is nothing wrong with the hard drive. After that I was totally puzzled. I found a few pointers online saying that the BIOS start-up block might be corrupted itself and I might need to flash/update the BIOS. I found the detailed instruction on how to create a Boot up disk by downloading the BIOS firmware from the manufacture's website. I did exactly as instructed below: Download the latest version or your choose version of BIOS file for your computer or motherboard from the manufacturer’s support site. Rename the downloaded file to AMIBOOT.ROM. Copy the file to a floppy disk. Insert the floppy disk to the floppy drive. Turn on the system. After I did that and powered on the PC to boot from the floppy drive, it gave me this error message: "Non-System Disk or Disk Error. Replace and Strike any key when ready." I did all that, and I kept on pressing [Ctrl]+[Home] to force it, but it did not did any satisfying result. Desperate as I am, my next attempt is to try the instruction below. Since I want to be ready, in the event it does not work, do you have any solution that you can provide? Please keep in mind that I cannot boot from any of the devices at this moment. My only hope now is to come on with a solution that will work through the Floppy drive, since that's the only drive that affected. Thank you very much for your advice and support in advance. To create a Windows startup disk, insert a floppy disk into the drive of a similarly configured, working Windows XP system, launch My Computer, right-click the floppy disk icon, and select the Format command from the context menu. When you see the Format dialog box, leave all the default settings as they are and click the Start button. Once the format operation is complete, close the Format dialog box to return to My Computer, double-click the drive C icon to access the root directory, and copy the following three files to the floppy disk: Boot.ini NTLDR Ntdetect.com

    Read the article

  • Using different SSDs types (not only SATA based) as system drive

    - by Hubert Kario
    Currently I have a Thinkpad X61s and want to make it both a bit faster and a bit more power efficient. For that reason I thought that adding SSD drive would make most sense. Unfortunately, because of financial reasons, buying SSD of over 200GB capacity is out of reach for me (not only it would be worth more than the rest of the laptop, but also I currently have a 500GB drive in it, so even such a drive would be kind of a downgrade for me). During preliminary testing with a cheap Transcend 4GB Class 6 (14MiB/s streaming, 9MiB/s random read) card I experienced boot times to be reduced by half so putting the OS only on it would already would be an improvement. Unfortunately, my system now is about 11GiB in size so anything less than 16GB would be constraining. In this laptop I can connect additional drives on at least 5 different ways: using SATA-ATA converter caddy in the X6 Ultrabase using internal mini PCIe slot using integrated SDHC slot using CardBus (a.k.a PCMCIA or PC Card) slot using USB Thankfully, because I use only Linux on this PC the bootability of them is irrelevant as I can put the /boot partition on internal HDD and / on any of the above mentioned Flash memories (as I already did for the SDHC test). From what I was able to research and from my own experience those options come with rather big downsides or other problems: SATA-ATA caddy It has three downsides: I have to carry the Ultrabse with me at all times (it's not really inconvenient, but those grams do add) and couldn't disconnect it when I want to disconnect the battery It makes the bay unusable for the optical drive and occasional quick access to other hard drives the only caddies I could buy have rather flaky controllers in them so putting my OS on it would hamper its stability Internal mini PCIe slot This would be an ideal solution, if only I could find real PCIe SSDs, not only devices that could talk only SATA or ATA over PCIe mechanical connection (the ones used in Dell Mini or Asus EEE). Theoretically Samsung did release such devices but I couldn't find them in retail anywhere. Integrated SDHC slot It's a nice solution with a single drawback: the fastest 16GB SDHC card on the market can only do around 35MiB/s read and 15MiB/s write while still costing like a normal 40GB SATA SSD that's 10 times faster. Not really cost-effective. CardBus (a.k.a PCMCIA or PC Card) slot Those cards are much faster than the SDHC option (there are ones that can do well over 50MiB/s read in benchmarks) and from what I could find the PCMCIA controller in my laptop does support UDMA so it should be able to deliver comparable speeds. They still cost similarly to SD cards but at least they provide streaming performance comparable to my current HDD. USB That's the worst option. Not only is it limited to 20-30MiB/s by the interface itself the drive would stick out of the laptop so it's a big no no. The question As such I think that going the "CF in a CardBus adapter" route will be the best option. My question is: did anyone try using CF cards in CardBus adapters as system drives with Linux on Thinkpad laptops? Laptops in general? What was the real-world performance? I don't have any CF cards so I can't check how well does it work with suspend/resume, or whatever it's easy to make it work in initramfs (I'm using ArchLinux and SD card was trivial — add 3 modules in single config line and rebuilding initramfs) so any tips/gotchas on this are welcome as well.

    Read the article

  • Hour-long shutdown duration "shutting down hyper-v virtual machine management service"

    - by icelava
    I have a Windows 2008 R2 server that is a Hyper-V host (Dell PowerEdge T300). Today for the first time I encountered an odd situation; i lost connection with one of the guest machines but logging on physically it seems the guest OS is still running but no longer contactable via the network. I tried to shut down the guest machine (Windows XP) but it would not shut down, getting stuck in a "Not responding" dialog box that cannot be dismissed. I used the Hyper-V management console to reset the machine and it could not get out of resetting state. I tried to save another Windows 2003 guest machine, and it would be progress with its Saving state (0%). The other running Windows 2003 guest was stuck in the logon dialog. My first suspicion is perhaps one of the Windows update patches this week (10 Nov 2011) may something to do with it, which was still pending a system restart. Well, since I could not do anything with Hyper-V i proceeded with the Windows Update restart, and now it is stuck half an hour at "Shutting down hyper-v virtual machine management service" Prior to restarting I did not observe any hard disk errors reported in the system event log; doubt it is a disk-related condition. Shall I force a hard reboot? UPDATE Ok so i left it hanging over an hour while attending to other matters, and thankfully the host cleanly restarted. I can operate the guest machines fine now. Phew. Hyper-V must have been crawling for some reason. The VMs have been observed to become slow in the past when the host has been up for a long duration (two weeks to a month), but never this slow. Would love to know what types of performance monitoring items i can observe to give a hint why this can happen. UPDATE 2012-02-13 In the months ever since, Hyper-V has stalled into this state another two times. It appears so randomly and without any error event logs to hint what is causing it enter this "drunkard" state. Just an Hyper-V management service timeout. Log Name: System Source: Service Control Manager Date: 13/2/2012 9:16:48 AM Event ID: 7043 Task Category: None Level: Error Keywords: Classic User: N/A Computer: elune Description: The Hyper-V Virtual Machine Management service did not shut down properly after receiving a preshutdown control. Event Xml: <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> <System> <Provider Name="Service Control Manager" Guid="{555908d1-a6d7-4695-8e1e-26931d2012f4}" EventSourceName="Service Control Manager" /> <EventID Qualifiers="49152">7043</EventID> <Version>0</Version> <Level>2</Level> <Task>0</Task> <Opcode>0</Opcode> <Keywords>0x8080000000000000</Keywords> <TimeCreated SystemTime="2012-02-13T01:16:48.882901900Z" /> <EventRecordID>567844</EventRecordID> <Correlation /> <Execution ProcessID="764" ThreadID="8484" /> <Channel>System</Channel> <Computer>elune</Computer> <Security /> </System> <EventData> <Data Name="param1">Hyper-V Virtual Machine Management</Data> </EventData> </Event> The only means out of it is to restart the system.

    Read the article

  • "ID 046d:c50e Logitech, Inc. Cordless Mouse Receiver" wheel-click is wrong

    - by sputnick
    I use this mouse under archlinux x86_64 with 3.2.8-1-ARCH kernel. I have some problems to select and then paste with the wheel-click in some applications like konversation, not in a terminal nor an editor. I don't know if it's a hardware problem or a software one. $ lsusb -v Bus 002 Device 110: ID 046d:c50e Logitech, Inc. Cordless Mouse Receiver Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 8 idVendor 0x046d Logitech, Inc. idProduct 0xc50e Cordless Mouse Receiver bcdDevice 25.10 iManufacturer 1 Logitech iProduct 2 USB RECEIVER iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 34 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xa0 (Bus Powered) Remote Wakeup MaxPower 70mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 3 Human Interface Device bInterfaceSubClass 1 Boot Interface Subclass bInterfaceProtocol 2 Mouse iInterface 0 HID Device Descriptor: bLength 9 bDescriptorType 33 bcdHID 1.11 bCountryCode 0 Not supported bNumDescriptors 1 bDescriptorType 34 Report wDescriptorLength 95 Report Descriptors: ** UNAVAILABLE ** Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0008 1x 8 bytes bInterval 10 Device Status: 0x0000 (Bus Powered) When I see what's happens in xev, the output is different compared to another mouse My buggy Logitech mouse : ButtonPress event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170350700, (48,52), root:(1491,75), state 0x10, button 11, same_screen YES EnterNotify event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x0, time 170350700, (48,52), root:(1491,75), mode NotifyGrab, detail NotifyInferior, same_screen YES, focus YES, state 16 KeymapNotify event, serial 40, synthetic NO, window 0x0, keys: 90 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ButtonPress event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170350716, (48,52), root:(1491,75), state 0x10, button 6, same_screen YES ButtonRelease event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170350716, (48,52), root:(1491,75), state 0x10, button 6, same_screen YES ButtonRelease event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170350988, (48,52), root:(1491,75), state 0x10, button 11, same_screen YES LeaveNotify event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x0, time 170350988, (48,52), root:(1491,75), mode NotifyUngrab, detail NotifyInferior, same_screen YES, focus YES, state 16 a working mouse (dell) : ButtonPress event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170245131, (46,32), root:(1489,55), state 0x10, button 2, same_screen YES EnterNotify event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x0, time 170245131, (46,32), root:(1489,55), mode NotifyGrab, detail NotifyInferior, same_screen YES, focus YES, state 528 KeymapNotify event, serial 40, synthetic NO, window 0x0, keys: 90 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ButtonRelease event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x4400002, time 170245411, (46,32), root:(1489,55), state 0x210, button 2, same_screen YES LeaveNotify event, serial 40, synthetic NO, window 0x4400001, root 0x15a, subw 0x0, time 170245411, (46,32), root:(1489,55), mode NotifyUngrab, detail NotifyInferior, same_screen YES, focus YES, state 16 A demo of the problem when I use konversation (IRC) : http://www.youtube.com/watch?v=lhmr92M7NCc I tried to modify the button map with xmodmap like this with no success (one at a time) : xmodmap -e "pointer = 1 0 3" xmodmap -e "pointer = 1 1 3" xmodmap -e "pointer = 1 2 3" xmodmap -e "pointer = 1 3 3" xmodmap -e "pointer = 1 4 3" xmodmap -e "pointer = 1 5 3" xmodmap -e "pointer = 1 6 3" xmodmap -e "pointer = 1 7 3" xmodmap -e "pointer = 1 8 3" xmodmap -e "pointer = 1 9 3" xmodmap -e "pointer = 1 10 3" xmodmap -e "pointer = 1 11 3" xmodmap -e "pointer = 1 12 3" xmodmap -e "pointer = 1 13 3" xmodmap -e "pointer = 1 14 3" xmodmap -e "pointer = 1 15 3" xmodmap -e "pointer = 1 16 3" xmodmap -e "pointer = 1 17 3" xmodmap -e "pointer = 1 18 3" xmodmap -e "pointer = 1 19 3" xmodmap -e "pointer = 1 20 3" xmodmap -e "pointer = 1 21 3" xmodmap -e "pointer = 1 22 3" xmodmap -e "pointer = 1 23 3" xmodmap -e "pointer = 1 24 3" xmodmap -e "pointer = 1 25 3" Any clue ? I would like to avoid buying a new mouse just for a paste problem.

    Read the article

  • Connecting PC to TV via HDMI/DVI: Windows XP doesn't allow the appropriate screen resolution

    - by Jørgen
    I have a computer that is connected to the living room TV (a Panasonic) via HDMI. There is no other monitor connected. My problem is that the computer, which is running Windows XP, does not allow me to set the proper resolution for the TV. Both the graphics adapter and the TV should support the 1280x720 resolution, but it cannot be selected - the only available options are 1280x600 and 800x600, both in the "native" Windows dialog box and the custom Intel graphics options dialog box. Do anyone have a suggestion for a solution for this? Things I've thought of: Setting the resolution directly in the registry (where?) Installing some "custom" monitor driver (the TV manufacturer does not appear to provide any, currently the "generic" one is used) Details on the setup: Connection: DVI output on the computer via a passive DVI-HDMI adapter to the HDMI input on the TV, audio is run on a separate link, the TV is able to combine video and audio without any problem, the problem is there regardless of whether or not the audio is connected. The connection is several meters long through some walls, for this reason using a VGA cable instead is not an option. Note that the report explicitly says that the TV supports 1280x720. Still, I am not allowed to select it in Graphics Options, only 1280x600 and 800x600 is available. For 800x600, there's a lot of black around the edges; for 1280x600, the screen is "zoomed" so the edges of the monitor image (like the taskbar) is not visible. Other: The computer is running Windows XP. More recent versions of Windows are not an option (I have no licence). Linux is probably not an option (some of the video streaming sites I plan to use do not support it, I think) I wrote the rest of the details below. Thanks for any help!! TV: Panasonic TX-L32X10Y, European version; a 720p 32" quite "regular" LCD TV. Allowed resolutions according to manual: Signal name: 640x480 @60HZ Horizontal frequency: 31.47 kHz Vertical frequency: 60Hz Signal name: 750/720) /60p Horizontal frequency: 45.00 kHz Vertical frequency: 60Hz Signal name: 1,125 (1,080) / 60p Horizontal frequency: 67.50 kHz Vertical frequency: 60Hz (this is exactly how the manual presents it. PC via D-SUB (VGA cable) and "regular" HDMI have more alternatives.) Messing with the "zoom" settings on the TV does not affect the available resolution options on the computer. Computer: The following is a printout from one of the graphics adapter option pages. I think it covers most of it. The computer is a Dell. INTEL(R) EXTREME GRAPHICS 2 REPORT Report Date: 04/17/2011 Report Time[hr:mm:ss]: 20:18:02 Driver Version: 6.14.10.4396 Operating System: Windows XP* Professional, Service Pack 3 (5.1.2600) Default Language: English DirectX* Version: 9.0 Physical Memory: 1021 MB Minimum Graphics Memory: 1 MB Maximum Graphics Memory: 96 MB Graphics Memory in Use: 6 MB Processor: x86 Processor Speed: 2593 MHZ Vendor ID: 8086 Device ID: 2572 Device Revision: 02 * Accelerator Information * Accelerator in Use: Intel(R) 82865G Graphics Controller Video BIOS: 2972 Current Graphics Mode: 1280 by 600 True Color (60 Hz) * Devices Connected to the Graphics Accelerator * Active Digital Displays: 1 * Digital Display * Monitor Name: Plug and Play Monitor Display Type: Digital Gamma Value: 2.20 DDC2 Protocol: Supported Maximum Image Size: Horizontal: Not Available Vertical: Not Available Monitor Supported Modes: 1280 by 720 (50 Hz) 1280 by 720 (60 Hz) Display Power Management Support: Standby Mode: Not Supported Suspend Mode: Not Supported Active Off Mode: Not Supported (disclaimer: this question was also asked at the Wikipedia Reference Desk some time ago and might show up in a Google search. I got no useful answers there.)

    Read the article

  • LightDM will not start after stopping it

    - by Sweeters
    I am running Ubuntu 11.10 "Oneiric Ocelot", and in trying to install the nvidia CUDA developer drivers I switched to a virtual terminal (Ctrl-Alt-F5) and stopped lightdm (installation required that no X server instance be running) through sudo service lightdm stop. Re-starting lightdm with sudo service lightdm start did not work: A couple of * Starting [...] lines where displayed, but the process hanged. (I do not remember at which point, but I think it was * Starting System V runlevel compatibility. I manually rebooted my laptop, and ever since booting seems to hang, usually around the * Starting anac(h)ronistic cron [OK] log line (not consistently at that point, though). From that point on, I seem to be able to interact with my system only through a tty session (Ctrl-Alt-F1). I've tried purging and reinstalling both lightdm and gdm, as well as selecting both as the default display managers (through sudo dpkg-reconfigure [lightdm / gdm] or by manually editing /etc/X11/default-display-manager) through both apt-get and aptitude (that shouldn't make a difference anyway) after updating the packages, but the problem persists. Some of the responses I'm getting are the following: After running sudo dpkg-reconfigure lightdm (but not ... gdm) I get the following message: dpkg-maintscript-helper:warning: environment variable DPKG_MATINSCRIPT_NAME missing dpkg-maintscript-helper:warning: environment variable DPKG_MATINSCRIPT_PACKAGE missing After trying sudo service lightdm start or sudo start lightdm I get to see the boot loading screen again but nothing changes. If I go back to the tty shell I see lightdm start/running, process <num> but ps -e | grep lightdm gives no output. After trying sudo service gdm start or sudo starg gdm I get the gdm start/running, process <num> message, and gdm-binary is supposedly an active process, but all that happens is that the screen blinks a couple of times and nothing else. Other candidate solutions that I'd found on the web included running startx but when I try that I get an error output [...] Fatal server error: no screens found [...]. Moreover, I made sure that lightdm-gtk-greeter is installed but that did not help either. Please excuse my not including complete outputs/logs; I am writing this post from another computer and it's hard to manually copy the complete logs. Also, I've seen several posts that had to do with similar problems, but either there was no fix, or the one suggested did not work for me. In closing: Please help! I very much hope to avoid re-installing Ubuntu from scratch! :) Alex @mosi I did not manage to fix the NVIDIA kernel driver as per your instructions. I should perhaps mention that I'm on a Dell XPS15 laptop with an NVIDIA Optimus graphics card, and that I have bumblebee installed (which installs nvidia drivers during its installation, I believe). Issuing the mentioned commands I get the following: ~$uname -r 3.0.0-12-generic ~$lsmod | grep -i nvidia nvidia 11713772 0 ~$dmesg | grep -i nvidia [ 8.980041] nvidia: module license 'NVIDIA' taints kernel. [ 9.354860] nvidia 0000:01:00.0: power state changed by ACPI to D0 [ 9.354864] nvidia 0000:01:00.0: power state changed by ACPI to D0 [ 9.354868] nvidia 0000:01:00.0: enabling device (0006 -> 0007) [ 9.354873] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 9.354879] nvidia 0000:01:00.0: setting latency timer to 64 [ 9.355052] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 280.13 Wed Jul 27 16:53:56 PDT 2011 Also, running aptitude search nvidia gives me the following: p nvidia-173 - NVIDIA binary Xorg driver, kernel module a p nvidia-173-dev - NVIDIA binary Xorg driver development file p nvidia-173-updates - NVIDIA binary Xorg driver, kernel module a p nvidia-173-updates-dev - NVIDIA binary Xorg driver development file p nvidia-96 - NVIDIA binary Xorg driver, kernel module a p nvidia-96-dev - NVIDIA binary Xorg driver development file p nvidia-96-updates - NVIDIA binary Xorg driver, kernel module a p nvidia-96-updates-dev - NVIDIA binary Xorg driver development file p nvidia-cg-toolkit - Cg Toolkit - GPU Shader Authoring Language p nvidia-common - Find obsolete NVIDIA drivers i nvidia-current - NVIDIA binary Xorg driver, kernel module a p nvidia-current-dev - NVIDIA binary Xorg driver development file c nvidia-current-updates - NVIDIA binary Xorg driver, kernel module a p nvidia-current-updates-dev - NVIDIA binary Xorg driver development file i nvidia-settings - Tool of configuring the NVIDIA graphics dr p nvidia-settings-updates - Tool of configuring the NVIDIA graphics dr v nvidia-va-driver - v nvidia-va-driver - I've tried manually installing (sudo aptitude install <package>) packages nvidia-common and nvidia-settings-updates but to no avail. For example, sudo aptitude install nvidia-settings-updates returns the following log: Reading package lists... Building dependency tree... Reading state information... Reading extended state information... Initializing package states... Writing extended state information... No packages will be installed, upgraded, or removed. 0 packages upgraded, 0 newly installed, 0 to remove and 83 not upgraded. Need to get 0 B of archives. After unpacking 0 B will be used. Writing extended state information... Reading package lists... Building dependency tree... Reading state information... Reading extended state information... Initializing package states... Writing extended state information... The same happens with the Linux headers (i.e. I cannot seem to be able to install linux-headers-3.0.0-12-generic). The output of aptitude search linux-headers is as follows: v linux-headers - v linux-headers - v linux-headers-2.6 - i linux-headers-2.6.38-11 - Header files related to Linux kernel versi i linux-headers-2.6.38-11-generic - Linux kernel headers for version 2.6.38 on i A linux-headers-2.6.38-8 - Header files related to Linux kernel versi i A linux-headers-2.6.38-8-generic - Linux kernel headers for version 2.6.38 on v linux-headers-3 - v linux-headers-3.0 - v linux-headers-3.0 - i A linux-headers-3.0.0-12 - Header files related to Linux kernel versi p linux-headers-3.0.0-12-generic - Linux kernel headers for version 3.0.0 on p linux-headers-3.0.0-12-generic- - Linux kernel headers for version 3.0.0 on p linux-headers-3.0.0-12-server - Linux kernel headers for version 3.0.0 on p linux-headers-3.0.0-12-virtual - Linux kernel headers for version 3.0.0 on p linux-headers-generic - Generic Linux kernel headers p linux-headers-generic-pae - Generic Linux kernel headers v linux-headers-lbm - v linux-headers-lbm - v linux-headers-lbm-2.6 - v linux-headers-lbm-2.6 - p linux-headers-lbm-3.0.0-12-gene - Header files related to linux-backports-mo p linux-headers-lbm-3.0.0-12-gene - Header files related to linux-backports-mo p linux-headers-lbm-3.0.0-12-serv - Header files related to linux-backports-mo p linux-headers-server - Linux kernel headers on Server Equipment. p linux-headers-virtual - Linux kernel headers for virtual machines @heartsmagic I did try purging and reinstalling any nvidia driver packages, but it did not seem to make a difference, My xorg.conf file contains the following: # nvidia-xconfig: X configuration file generated by nvidia-xconfig # nvidia-xconfig: version 280.13 ([email protected]) Wed Jul 27 17:15:58 PDT 2011 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" 0 0 InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" EndSection Section "Files" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Unknown" ModelName "Unknown" HorizSync 28.0 - 33.0 VertRefresh 43.0 - 72.0 Option "DPMS" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" EndSection Section "Screen" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 SubSection "Display" Depth 24 EndSubSection EndSection

    Read the article

  • And What's Your Brand Worth? ...anything?

    - by [email protected]
    100 Best Global Brands from Business Week Story: The Great Trust Offensive Slide Show: Top Brands 2009 Methodology: Picking the Winners The recession has presented marketing executives around the world with the toughest test of their careers. Some brands have prospered amid the hard times--or at least held their own. Others have slipped a surprising number of places on our ninth annual ranking, compiled by consultancy Interbrand. But for seven brands, impressive performances saw them race up the charts to take their place on this year's list. Here are the numbers behind the rankings Rank 2009 Rank 2008 Employer 2009 Brand value($millions) 2008 Brand value($millions) Percent change(%) Country of Ownership 1 1 Coca-Cola  68,734  66,667  3 U.S. 2 2 IBM  60,211  59,031  2 U.S. 3 3 Microsoft  56,647  59,007  -4 U.S. 4 4 GE  47,777  53,086  -10 U.S. 5 5 Nokia  34,864  35,942  -3 Finland 6 8 McDonald's  32,275  31,049  4 U.S. 7 10 Google  31,980  25,590  25 U.S. 8 6 Toyota  31,330  34,050  -8 Japan 9 7 Intel  30,636  31,261  -2 U.S. 10 9 Disney  28,447  29,251  -3 U.S. 11 12 Hewlett-Packard  24,096  23,509  2 U.S. 12 11 Mercedes-Benz  23,867  25,577  -7 Germany 13 14 Gillette  22,841  22,069  4 U.S. 14 17 Cisco  22,030  21,306  3 U.S. 15 13 BMW  21,671  23,298  -7 Germany 16 16 Louis Vuitton  21,120  21,602  -2 France 17 18 Marlboro  19,010  21,300  -11 U.S. 18 20 Honda  17,803  19,079  -7 Japan 19 21 Samsung  17,518  17,689  -1 S. Korea 20 24 Apple  15,443  13,724  12 U.S. 21 22 H&M  15,375  13,840  11 Sweden 22 15 American Express  14,971  21,940  -32 U.S. 23 26 Pepsi  13,706  13,249  3 U.S. 24 23 Oracle  13,699  13,831  -1 U.S. 25 28 Nescafe  13,317  13,055  2 Switzerland 26 29 Nike  13,179  12,672  4 U.S. 27 31 SAP  12,106  12,228  -1 Germany 28 35 Ikea  12,004  10,913  10 Sweden 29 25 Sony  11,953  13,583  -12 Japan 30 33 Budweiser  11,833  11,438  3 Belgium 31 30 UPS  11,594  12,621  -8 U.S. 32 27 HSBC  10,510  13,143  -20 Britain 33 36 Canon  10,441  10,876  -4 Japan 34 39 Kellogg's  10,428  9,710  7 U.S. 35 32 Dell  10,291  11,695  -12 U.S. 36 19 Citi  10,254  20,174  -49 U.S. 37 37 JPMorgan  9,550  10,773  -11 U.S. 38 38 Goldman Sachs  9,248  10,331  -10 U.S. 39 40 Nintendo  9,210  8,772  5 Japan 40 44 Thomson Reuters  8,434  8,313  1 Canada 41 45 Gucci  8,182  8,254  -1 Italy 42 43 Philips  8,121  8,325  -2 Netherlands 43 58 Amazon  7,858  6,434  22 U.S. 44 51 L'Oreal  7,748  7,508  3 France 45 47 Accenture  7,710  7,948  -3 U.S. 46 46 eBay  7,350  7,991  -8 U.S. 47 48 Siemens  7,308  7,943  -8 Germany 48 56 Heinz  7,244  6,646  9 U.S. 49 49 Ford  7,005  7,896  -11 U.S. 50 62 Zara  6,789  5,955  14 Spain   Valuations do not represent a guarantee of future performance of the brands or companies. Data: Interbrand, BusinessWeek

    Read the article

  • No GLX on Intel card with multiseat with additional nVidia card

    - by MeanEYE
    I have multiseat configured and my Xorg has 2 server layouts. One is for nVidia card and other is for Intel card. They both work, but display server assigned to Intel card doesn't have hardware acceleration since DRI and GLX module being used is from nVidia driver. So my question is, can I configure layouts somehow to use right DRI and GLX with each card? My Xorg.conf: Section "ServerLayout" Identifier "Default" Screen 0 "Screen0" 0 0 Option "Xinerama" "0" EndSection Section "ServerLayout" Identifier "TV" Screen 0 "Screen1" 0 0 Option "Xinerama" "0" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor0" VendorName "Unknown" ModelName "DELL E198WFP" HorizSync 30.0 - 83.0 VertRefresh 56.0 - 75.0 Option "DPMS" EndSection Section "Monitor" Identifier "Monitor1" VendorName "Unknown" Option "DPMS" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce GT 610" EndSection Section "Device" Identifier "Device1" Driver "intel" BusID "PCI:0:2:0" Option "AccelMethod" "uxa" EndSection Section "Screen" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "Stereo" "0" Option "nvidiaXineramaInfoOrder" "DFP-1" Option "metamodes" "DFP-0: nvidia-auto-select +1440+0, DFP-1: nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen1" Device "Device1" Monitor "Monitor1" DefaultDepth 24 SubSection "Display" Depth 24 EndSubSection EndSection Log file for Intel: [ 18.239] X.Org X Server 1.13.0 Release Date: 2012-09-05 [ 18.239] X Protocol Version 11, Revision 0 [ 18.239] Build Operating System: Linux 2.6.24-32-xen x86_64 Ubuntu [ 18.239] Current Operating System: Linux bytewiper 3.5.0-18-generic #29-Ubuntu SMP Fri Oct 19 10:26:51 UTC 2012 x86_64 [ 18.239] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.5.0-18-generic root=UUID=fc0616fd-f212-4846-9241-ba4a492f0513 ro quiet splash [ 18.239] Build Date: 20 September 2012 11:55:20AM [ 18.239] xorg-server 2:1.13.0+git20120920.70e57668-0ubuntu0ricotz (For technical support please see http://www.ubuntu.com/support) [ 18.239] Current version of pixman: 0.26.0 [ 18.239] Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. [ 18.239] Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. [ 18.239] (==) Log file: "/var/log/Xorg.1.log", Time: Wed Nov 21 18:32:14 2012 [ 18.239] (==) Using config file: "/etc/X11/xorg.conf" [ 18.239] (==) Using system config directory "/usr/share/X11/xorg.conf.d" [ 18.239] (++) ServerLayout "TV" [ 18.239] (**) |-->Screen "Screen1" (0) [ 18.239] (**) | |-->Monitor "Monitor1" [ 18.240] (**) | |-->Device "Device1" [ 18.240] (**) Option "Xinerama" "0" [ 18.240] (==) Automatically adding devices [ 18.240] (==) Automatically enabling devices [ 18.240] (==) Automatically adding GPU devices [ 18.240] (WW) The directory "/usr/share/fonts/X11/cyrillic" does not exist. [ 18.240] Entry deleted from font path. [ 18.240] (WW) The directory "/usr/share/fonts/X11/100dpi/" does not exist. [ 18.240] Entry deleted from font path. [ 18.240] (WW) The directory "/usr/share/fonts/X11/75dpi/" does not exist. [ 18.240] Entry deleted from font path. [ 18.240] (WW) The directory "/usr/share/fonts/X11/100dpi" does not exist. [ 18.240] Entry deleted from font path. [ 18.240] (WW) The directory "/usr/share/fonts/X11/75dpi" does not exist. [ 18.240] Entry deleted from font path. [ 18.240] (WW) The directory "/var/lib/defoma/x-ttcidfont-conf.d/dirs/TrueType" does not exist. [ 18.240] Entry deleted from font path. [ 18.240] (==) FontPath set to: /usr/share/fonts/X11/misc, /usr/share/fonts/X11/Type1, built-ins [ 18.240] (==) ModulePath set to "/usr/lib/x86_64-linux-gnu/xorg/extra-modules,/usr/lib/xorg/extra-modules,/usr/lib/xorg/modules" [ 18.240] (II) The server relies on udev to provide the list of input devices. If no devices become available, reconfigure udev or disable AutoAddDevices. [ 18.240] (II) Loader magic: 0x7f6917944c40 [ 18.240] (II) Module ABI versions: [ 18.240] X.Org ANSI C Emulation: 0.4 [ 18.240] X.Org Video Driver: 13.0 [ 18.240] X.Org XInput driver : 18.0 [ 18.240] X.Org Server Extension : 7.0 [ 18.240] (II) config/udev: Adding drm device (/dev/dri/card0) [ 18.241] (--) PCI: (0:0:2:0) 8086:0152:1043:84ca rev 9, Mem @ 0xf7400000/4194304, 0xd0000000/268435456, I/O @ 0x0000f000/64 [ 18.241] (--) PCI:*(0:1:0:0) 10de:104a:1458:3546 rev 161, Mem @ 0xf6000000/16777216, 0xe0000000/134217728, 0xe8000000/33554432, I/O @ 0x0000e000/128, BIOS @ 0x????????/524288 [ 18.241] (II) Open ACPI successful (/var/run/acpid.socket) [ 18.241] Initializing built-in extension Generic Event Extension [ 18.241] Initializing built-in extension SHAPE [ 18.241] Initializing built-in extension MIT-SHM [ 18.241] Initializing built-in extension XInputExtension [ 18.241] Initializing built-in extension XTEST [ 18.241] Initializing built-in extension BIG-REQUESTS [ 18.241] Initializing built-in extension SYNC [ 18.241] Initializing built-in extension XKEYBOARD [ 18.241] Initializing built-in extension XC-MISC [ 18.241] Initializing built-in extension SECURITY [ 18.241] Initializing built-in extension XINERAMA [ 18.241] Initializing built-in extension XFIXES [ 18.241] Initializing built-in extension RENDER [ 18.241] Initializing built-in extension RANDR [ 18.241] Initializing built-in extension COMPOSITE [ 18.241] Initializing built-in extension DAMAGE [ 18.241] Initializing built-in extension MIT-SCREEN-SAVER [ 18.241] Initializing built-in extension DOUBLE-BUFFER [ 18.241] Initializing built-in extension RECORD [ 18.241] Initializing built-in extension DPMS [ 18.241] Initializing built-in extension X-Resource [ 18.241] Initializing built-in extension XVideo [ 18.241] Initializing built-in extension XVideo-MotionCompensation [ 18.241] Initializing built-in extension XFree86-VidModeExtension [ 18.241] Initializing built-in extension XFree86-DGA [ 18.241] Initializing built-in extension XFree86-DRI [ 18.241] Initializing built-in extension DRI2 [ 18.241] (II) LoadModule: "glx" [ 18.241] (II) Loading /usr/lib/x86_64-linux-gnu/xorg/extra-modules/libglx.so [ 18.247] (II) Module glx: vendor="NVIDIA Corporation" [ 18.247] compiled for 4.0.2, module version = 1.0.0 [ 18.247] Module class: X.Org Server Extension [ 18.247] (II) NVIDIA GLX Module 310.19 Thu Nov 8 01:12:43 PST 2012 [ 18.247] Loading extension GLX [ 18.247] (II) LoadModule: "intel" [ 18.248] (II) Loading /usr/lib/xorg/modules/drivers/intel_drv.so [ 18.248] (II) Module intel: vendor="X.Org Foundation" [ 18.248] compiled for 1.13.0, module version = 2.20.13 [ 18.248] Module class: X.Org Video Driver [ 18.248] ABI class: X.Org Video Driver, version 13.0 [ 18.248] (II) intel: Driver for Intel Integrated Graphics Chipsets: i810, i810-dc100, i810e, i815, i830M, 845G, 854, 852GM/855GM, 865G, 915G, E7221 (i915), 915GM, 945G, 945GM, 945GME, Pineview GM, Pineview G, 965G, G35, 965Q, 946GZ, 965GM, 965GME/GLE, G33, Q35, Q33, GM45, 4 Series, G45/G43, Q45/Q43, G41, B43, B43, Clarkdale, Arrandale, Sandybridge Desktop (GT1), Sandybridge Desktop (GT2), Sandybridge Desktop (GT2+), Sandybridge Mobile (GT1), Sandybridge Mobile (GT2), Sandybridge Mobile (GT2+), Sandybridge Server, Ivybridge Mobile (GT1), Ivybridge Mobile (GT2), Ivybridge Desktop (GT1), Ivybridge Desktop (GT2), Ivybridge Server, Ivybridge Server (GT2), Haswell Desktop (GT1), Haswell Desktop (GT2), Haswell Desktop (GT2+), Haswell Mobile (GT1), Haswell Mobile (GT2), Haswell Mobile (GT2+), Haswell Server (GT1), Haswell Server (GT2), Haswell Server (GT2+), Haswell SDV Desktop (GT1), Haswell SDV Desktop (GT2), Haswell SDV Desktop (GT2+), Haswell SDV Mobile (GT1), Haswell SDV Mobile (GT2), Haswell SDV Mobile (GT2+), Haswell SDV Server (GT1), Haswell SDV Server (GT2), Haswell SDV Server (GT2+), Haswell ULT Desktop (GT1), Haswell ULT Desktop (GT2), Haswell ULT Desktop (GT2+), Haswell ULT Mobile (GT1), Haswell ULT Mobile (GT2), Haswell ULT Mobile (GT2+), Haswell ULT Server (GT1), Haswell ULT Server (GT2), Haswell ULT Server (GT2+), Haswell CRW Desktop (GT1), Haswell CRW Desktop (GT2), Haswell CRW Desktop (GT2+), Haswell CRW Mobile (GT1), Haswell CRW Mobile (GT2), Haswell CRW Mobile (GT2+), Haswell CRW Server (GT1), Haswell CRW Server (GT2), Haswell CRW Server (GT2+), ValleyView PO board [ 18.248] (++) using VT number 8 [ 18.593] (II) intel(0): using device path '/dev/dri/card0' [ 18.593] (**) intel(0): Depth 24, (--) framebuffer bpp 32 [ 18.593] (==) intel(0): RGB weight 888 [ 18.593] (==) intel(0): Default visual is TrueColor [ 18.593] (**) intel(0): Option "AccelMethod" "uxa" [ 18.593] (--) intel(0): Integrated Graphics Chipset: Intel(R) Ivybridge Desktop (GT1) [ 18.593] (**) intel(0): Relaxed fencing enabled [ 18.593] (**) intel(0): Wait on SwapBuffers? enabled [ 18.593] (**) intel(0): Triple buffering? enabled [ 18.593] (**) intel(0): Framebuffer tiled [ 18.593] (**) intel(0): Pixmaps tiled [ 18.593] (**) intel(0): 3D buffers tiled [ 18.593] (**) intel(0): SwapBuffers wait enabled ... [ 20.312] (II) Module fb: vendor="X.Org Foundation" [ 20.312] compiled for 1.13.0, module version = 1.0.0 [ 20.312] ABI class: X.Org ANSI C Emulation, version 0.4 [ 20.312] (II) Loading sub module "dri2" [ 20.312] (II) LoadModule: "dri2" [ 20.312] (II) Module "dri2" already built-in [ 20.312] (==) Depth 24 pixmap format is 32 bpp [ 20.312] (II) intel(0): [DRI2] Setup complete [ 20.312] (II) intel(0): [DRI2] DRI driver: i965 [ 20.312] (II) intel(0): Allocated new frame buffer 1920x1080 stride 7680, tiled [ 20.312] (II) UXA(0): Driver registered support for the following operations: [ 20.312] (II) solid [ 20.312] (II) copy [ 20.312] (II) composite (RENDER acceleration) [ 20.312] (II) put_image [ 20.312] (II) get_image [ 20.312] (==) intel(0): Backing store disabled [ 20.312] (==) intel(0): Silken mouse enabled [ 20.312] (II) intel(0): Initializing HW Cursor [ 20.312] (II) intel(0): RandR 1.2 enabled, ignore the following RandR disabled message. [ 20.313] (**) intel(0): DPMS enabled [ 20.313] (==) intel(0): Intel XvMC decoder enabled [ 20.313] (II) intel(0): Set up textured video [ 20.313] (II) intel(0): [XvMC] xvmc_vld driver initialized. [ 20.313] (II) intel(0): direct rendering: DRI2 Enabled [ 20.313] (==) intel(0): hotplug detection: "enabled" [ 20.332] (--) RandR disabled [ 20.335] (EE) Failed to initialize GLX extension (Compatible NVIDIA X driver not found) [ 20.335] (II) intel(0): Setting screen physical size to 508 x 285 [ 20.338] (II) XKB: reuse xkmfile /var/lib/xkb/server-B20D7FC79C7F597315E3E501AEF10E0D866E8E92.xkm [ 20.340] (II) config/udev: Adding input device Power Button (/dev/input/event1) [ 20.340] (**) Power Button: Applying InputClass "evdev keyboard catchall" [ 20.340] (II) LoadModule: "evdev" [ 20.340] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so

    Read the article

  • Load-balancing between a Procurve switch and a server

    - by vlad
    Hello I've been searching around the web for this problem i've been having. It's similar in a way to this question: How exactly & specifically does layer 3 LACP destination address hashing work? My setup is as follows: I have a central switch, a Procurve 2510G-24, image version Y.11.16. It's the center of a star topology, there are four switches connected to it via a single gigabit link. Those switches service the users. On the central switch, I have a server with two gigabit interfaces that I want to bond together in order to achieve higher throughput, and two other servers that have single gigabit connections to the switch. The topology looks as follows: sw1 sw2 sw3 sw4 | | | | --------------------- | sw0 | --------------------- || | | srv1 srv2 srv3 The servers were running FreeBSD 8.1. On srv1 I set up a lagg interface using the lacp protocol, and on the switch I set up a trunk for the two ports using lacp as well. The switch showed that the server was a lacp partner, I could ping the server from another computer, and the server could ping other computers. If I unplugged one of the cables, the connection would keep working, so everything looked fine. Until I tested throughput. There was only one link used between srv1 and sw0. All testing was conducted with iperf, and load distribution was checked with systat -ifstat. I was looking to test the load balancing for both receive and send operations, as I want this server to be a file server. There were therefore two scenarios: iperf -s on srv1 and iperf -c on the other servers iperf -s on the other servers and iperf -c on srv1 connected to all the other servers. Every time only one link was used. If one cable was unplugged, the connections would keep going. However, once the cable was plugged back in, the load was not distributed. Each and every server is able to fill the gigabit link. In one-to-one test scenarios, iperf was reporting around 940Mbps. The CPU usage was around 20%, which means that the servers could withstand a doubling of the throughput. srv1 is a dell poweredge sc1425 with onboard intel 82541GI nics (em driver on freebsd). After troubleshooting a previous problem with vlan tagging on top of a lagg interface, it turned out that the em could not support this. So I figured that maybe something else is wrong with the em drivers and / or lagg stack, so I started up backtrack 4r2 on this same server. So srv1 now uses linux kernel 2.6.35.8. I set up a bonding interface bond0. The kernel module was loaded with option mode=4 in order to get lacp. The switch was happy with the link, I could ping to and from the server. I could even put vlans on top of the bonding interface. However, only half the problem was solved: if I used srv1 as a client to the other servers, iperf was reporting around 940Mbps for each connection, and bwm-ng showed, of course, a nice distribution of the load between the two nics; if I run the iperf server on srv1 and tried to connect with the other servers, there was no load balancing. I thought that maybe I was out of luck and the hashes for the two mac addresses of the clients were the same, so I brought in two new servers and tested with the four of them at the same time, and still nothing changed. I tried disabling and reenabling one of the links, and all that happened was the traffic switched from one link to the other and back to the first again. I also tried setting the trunk to "plain trunk mode" on the switch, and experimented with other bonding modes (roundrobin, xor, alb, tlb) but I never saw any traffic distribution. One interesting thing, though: one of the four switches is a Cisco 2950, image version 12.1(22)EA7. It has 48 10/100 ports and 2 gigabit uplinks. I have a server (call it srv4) with a 4 channel trunk connected to it (4x100), FreeBSD 8.0 release. The switch is connected to sw0 via gigabit. If I set up an iperf server on one of the servers connected to sw0 and a client on srv4, ALL 4 links are used, and iperf reports around 330Mbps. systat -ifstat shows all four interfaces are used. The cisco port-channel uses src-mac to balance the load. The HP should use both the source and destination according to the manual, so it should work as well. Could this mean there is some bug in the HP firmware? Am I doing something wrong?

    Read the article

  • RAID1 rebuild fails due to disk errors

    - by overlord_tm
    Quick info: Dell R410 with 2x500GB drives in RAID1 on H700 Adapter Recently one of drives in RAID1 array on server failed, lets call it Drive 0. RAID controller marked it as fault and put it offline. I replaced faulty disk with new one (same series and manufacturer, just bigger) and configured new disk as hot spare. Rebuild from Drive1 started immediately and after 1.5 hour I got message that Drive 1 failed. Server was unresponsive (kernel panic) and required reboot. Given that half hour before this error rebuild was at about 40%, I estimated that new drive is not in sync yet and tried to reboot just with Drive 1. RAID controller complained a bit about missing RAID arrays, but it found foreign RAID array on Drive 1 and I imported it. Server booted and it runs (from degraded RAID). Here is SMART data for disks. Drive 0 (the one that failed first) ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 1 3 Spin_Up_Time POS--K 142 142 021 - 3866 4 Start_Stop_Count -O--CK 100 100 000 - 12 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 086 086 000 - 10432 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 11 192 Power-Off_Retract_Count -O--CK 200 200 000 - 10 193 Load_Cycle_Count -O--CK 200 200 000 - 1 194 Temperature_Celsius -O---K 112 106 000 - 31 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 200 200 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 198 000 - 3 And Drive 1 (the drive which was reported healthy from controller until rebuild was attempted) ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 35 3 Spin_Up_Time POS--K 143 143 021 - 3841 4 Start_Stop_Count -O--CK 100 100 000 - 12 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 086 086 000 - 10455 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 11 192 Power-Off_Retract_Count -O--CK 200 200 000 - 10 193 Load_Cycle_Count -O--CK 200 200 000 - 1 194 Temperature_Celsius -O---K 114 105 000 - 29 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 3 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0 In extended error logs from SMART I found: Drive 0 has only one error Error 1 [0] occurred at disk power-on lifetime: 10282 hours (428 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 18 00 00 00 6a 24 20 40 00 Error: IDNF at LBA = 0x006a2420 = 6956064 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 60 00 f8 00 00 00 6a 24 20 40 00 17d+20:25:18.105 WRITE FPDMA QUEUED 61 00 18 00 60 00 00 00 6a 24 00 40 00 17d+20:25:18.105 WRITE FPDMA QUEUED 61 00 80 00 58 00 00 00 6a 23 80 40 00 17d+20:25:18.105 WRITE FPDMA QUEUED 61 00 68 00 50 00 00 00 6a 23 18 40 00 17d+20:25:18.105 WRITE FPDMA QUEUED 61 00 10 00 10 00 00 00 6a 23 00 40 00 17d+20:25:18.104 WRITE FPDMA QUEUED But Drive 1 has 883 errors. I see only few last ones and all errors I can see look like this: Error 883 [18] occurred at disk power-on lifetime: 10454 hours (435 days + 14 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 01 -- 51 00 80 00 00 39 97 19 c2 40 00 Error: AMNF at LBA = 0x399719c2 = 966203842 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 60 00 80 00 00 00 00 39 97 19 80 40 00 1d+00:25:57.802 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 1d+00:25:57.779 READ LOG EXT 60 00 80 00 00 00 00 39 97 19 80 40 00 1d+00:25:55.704 READ FPDMA QUEUED 2f 00 00 00 01 00 00 00 00 00 10 40 00 1d+00:25:55.681 READ LOG EXT 60 00 80 00 00 00 00 39 97 19 80 40 00 1d+00:25:53.606 READ FPDMA QUEUED Given those errors, is there any way I can rebuild RAID back, or should I make backup, shutdown server, replace disks with new ones and restore it? What about if I dd faulty disk to new one from linux running on USB/CD? Also, if anyone have more experiences, what could be causes for those errors? Crappy controller or disks? Disks are about 1 year old, but it is pretty unbelievable to me that both would die within so short timespan.

    Read the article

  • Installing Windows on HP Proliant Servers without SmartStart

    - by Fitzroy
    I have a PXE server for deploying Windows XP and Windows 7 to workstations. The process is as follows: Boot the workstation from the NIC. Workstation sends a DHCP request. DHCP server responds with an IP address and the location of the PXE server. Workstation downloads WinPE image file from PXE server via TFTP Workstation stores WinPE image file in memory and executes it. Once booted into WinPE, I connect to a network share to gain access to either the Windows XP or Windows 7 installation files. A custom script is launched to guide you through the process of formatting and partitioning the hard drive(s) (using DISKPART and FORMAT). Another custom script asks for details such as the hostname to assign to the workstation. The answers provided are used to build an unattended answer file (SIF [Setup Information File] for WinXP and XML for Win7). The Windows setup EXE is launched, passing the unattended answer file to it as a parameter. The Windows XP and Windows 7 installation sources have been customised to include the drivers for our Dell workstations. They also run a number of scripts upon first booting up to install software packages. This process works very well for our workstations and I would now like to use it for building our servers too. The vast majority of our servers are HP Proliant DL360 G6, DL380 G5 and DL380 G6. They’re running Windows Server 2003 (various editions) or 2008 (various editions). To date, we have always built the HP Proliant servers using the SmartStart CD provided. SmartStart does three useful things for us: Setup RAID with HP Array Configuration Utility (ACU). Installs and configures SNMP Installs various HP Tools for Windows (HP Array Configuration Utility, HP Array Diagnostic Utility, HP Proliant Integrated Management Log Viewer, etc) Using SmartStart I have never had to manually download and install Windows drivers for network, sound, video, etc. I'm not sure if this is because SmartStart copies drivers from the CD during setup, or whether Windows just has the drivers natively in its driver CAB. If I abandon the SmartStart CD in favour of my PXE server I would have to do the following: As I wont have access to ACU, I'll configure the RAID (before booting to the PXE server) by pressing F8 (during the boot process) to access Option ROM Configuration for Arrays (ORCA). Installation of SNMP and the HP Tools will have to be installed once the Windows installation is complete using the Proliant Support Pack. Is this method OK? Is there anything that the SmartStart CD does that I'll be unable to do by other means? Are there any disadvantages to not using the SmartStart CD? Many thanks. UPDATE 05/01/12 I’ve been reading through the SmartStart Scripting Toolkit documentation. The scripting toolkit contains command line tools which work within WinPE and can such things as configure BIOS settings, configure an array and setup ILO. I’m personally not too bothered about configuring BIOS settings as I rarely deviate from the defaults (unless the server is to be a Hyper-V host). I’m not too fussed about being able to configure the array from within WinPE, as I’m happy to just press F8 and use Option ROM Configuration for Arrays (ORCA). Although, if it’s easy enough to do, I will explore this further, as it saves time if everything can be configured from within WinPE. One of the nice features all the tools possess is that you can pass input files to them. EG. Configure one server to your requirements, capture its configuration to a file (using the appropriate tool), you can then use the tool on other servers passing the input file with the captured configuration. Array controller drivers appear to be included with the toolkit along with example of how to incorporate them within a WinPE build. I suppose WinPE won’t be able to see logical volumes (I.E 2x physical disks in a RAID 1 configuration) without the array controller drivers? I mentioned in my post that SmartStart normally installs a bunch of Windows HP tools for you. I’ve had a look today, and if you run the SmartStart CD from within Windows all the tools can be installed. Therefore I can do this after the Windows installation is complete. The SmartStart CD appears to contain a lot Windows drivers. I can customise my Windows 2008 source to incorporate these drivers. However, I understand that incorporating an array controller driver is a little different to most drivers. I believe that you have to provide the driver during the very early stages of the Windows setup. I’m working through the Scripting Toolkit documentation to try and work this out...

    Read the article

  • Wireshark does not see interfaces (winXP)

    - by bua
    Short story: Wireshark is working....on my winXP-32b ... usage .... Long long time later Wireshark does not work It can't find any usefull interface (just VPN) ipconfig /all Ethernet adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Dell Wireless 1490 Dual Band WLAN Mini-Card Physical Address. . . . . . . . . : SOME VALID MAC Ethernet adapter eth0: Connection-specific DNS Suffix . : xxxx Description . . . . . . . . . . . : Broadcom 440x 10/100 Integrated Controller Physical Address. . . . . . . . . : SOME VALID MAC Dhcp Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes IP Address. . . . . . . . . . . . : 192.168.12.68 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168..... ..... Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Fortinet virtual adapter Physical Address. . . . . . . . . : SOME VALID MAC Following steps didn't help: Several Wireshark re-installation Several LIBPCAP re installation SP3 for winXP Any ideas welcome.

    Read the article

  • Parallel processing via multithreading in Java

    - by Robz
    There are certain algorithms whose running time can decrease significantly when one divides up a task and gets each part done in parallel. One of these algorithms is merge sort, where a list is divided into infinitesimally smaller parts and then recombined in a sorted order. I decided to do an experiment to test whether or not I could I increase the speed of this sort by using multiple threads. I am running the following functions in Java on a Quad-Core Dell with Windows Vista. One function (the control case) is simply recursive: // x is an array of N elements in random order public int[] mergeSort(int[] x) { if (x.length == 1) return x; // Dividing the array in half int[] a = new int[x.length/2]; int[] b = new int[x.length/2+((x.length%2 == 1)?1:0)]; for(int i = 0; i < x.length/2; i++) a[i] = x[i]; for(int i = 0; i < x.length/2+((x.length%2 == 1)?1:0); i++) b[i] = x[i+x.length/2]; // Sending them off to continue being divided mergeSort(a); mergeSort(b); // Recombining the two arrays int ia = 0, ib = 0, i = 0; while(ia != a.length || ib != b.length) { if (ia == a.length) { x[i] = b[ib]; ib++; } else if (ib == b.length) { x[i] = a[ia]; ia++; } else if (a[ia] < b[ib]) { x[i] = a[ia]; ia++; } else { x[i] = b[ib]; ib++; } i++; } return x; } The other is in the 'run' function of a class that extends thread, and recursively creates two new threads each time it is called: public class Merger extends Thread { int[] x; boolean finished; public Merger(int[] x) { this.x = x; } public void run() { if (x.length == 1) { finished = true; return; } // Divide the array in half int[] a = new int[x.length/2]; int[] b = new int[x.length/2+((x.length%2 == 1)?1:0)]; for(int i = 0; i < x.length/2; i++) a[i] = x[i]; for(int i = 0; i < x.length/2+((x.length%2 == 1)?1:0); i++) b[i] = x[i+x.length/2]; // Begin two threads to continue to divide the array Merger ma = new Merger(a); ma.run(); Merger mb = new Merger(b); mb.run(); // Wait for the two other threads to finish while(!ma.finished || !mb.finished) ; // Recombine the two arrays int ia = 0, ib = 0, i = 0; while(ia != a.length || ib != b.length) { if (ia == a.length) { x[i] = b[ib]; ib++; } else if (ib == b.length) { x[i] = a[ia]; ia++; } else if (a[ia] < b[ib]) { x[i] = a[ia]; ia++; } else { x[i] = b[ib]; ib++; } i++; } finished = true; } } It turns out that function that does not use multithreading actually runs faster. Why? Does the operating system and the java virtual machine not "communicate" effectively enough to place the different threads on different cores? Or am I missing something obvious?

    Read the article

< Previous Page | 99 100 101 102 103 104 105  | Next Page >