Search Results

Search found 2704 results on 109 pages for 'miguel ping'.

Page 103/109 | < Previous Page | 99 100 101 102 103 104 105 106 107 108 109  | Next Page >

  • Is there a switch that will connect directly to my modem and allow my router to serve only as a WiFi connection?

    - by Abner
    Details . . Devices . Internets -50Mbps Cable Internet Modem - Motorola Surfboard Extreme Router - Netgear WNDR3700v3 Switch - D-Link DGS-1008G Wired Ethernet Cable - Cat6_24Awg_ Device Configuration - Modem\Router\Switch . . Internet Usage . Wired Demand XBOX 360 1 Gaming PC 2 PC - HD video . WiFi Demand 3 android + 1 Laptop for browsing and group video chat simultaneously . . Specifics . I am experiencing problems with network speeds and reliability on both wired and wireless connections. On many occasions I experience WiFi Speeds that vary between the 15mbps to 0.50 mbs (or less) and ping ranging from 15ms to 500ms. These results are from when I notice problems with internet lag and run speedtest.net to get details of problems. I have a stretched out floor-plan and old building materials drastically affecting my cellphone signal strength as well). After Reading the "Known Issues" Section on the webpage below http://www.dd-wrt.com/wiki/index.php/Netgear_WNDR3700#Known_Issues I bought the switch and Cat6 cable to increase speed and relieve stress on router in an attempt to fix the symptoms. I thought I'd use the router in a Modem\Switch\Router configuration. I thought I'd only have to use the router for mobile WiFi connections like android or Laptops when necessary (hopefully eliminating the problem caused by the router when subjected to all those demanding Ethernet connections) When I started unboxing the switch, I noticed the manual of this DGS-1008G shows it being connected in the Modem\Router\Switch order and not in the Modem\Switch\Router configuration I was aiming for. I have not been able to find a solid plan to remedy my specific problem without buying another expensive router. I would like to get the speeds I am paying for without buying another router. (My WiFi Adapters would also need to be updated if new router is required, meaning more $$$). I can always sell the switch and get a better one that will bypass the router because my most demanding internet connections are Wired. . . Questions Can I accomplish a Modem\Switch\Router configuration with current switch? Is there a different way to get the wired speed I need while providing WiFi only when necessary? . .

    Read the article

  • weird SSH connection timed out

    - by bran
    This problem started when I tried to login to my brand spaning new VPS server. I remember that in my first SSH try on the server I actually got prompt for password several times which would mean that there is no port blocking problem from my isp. Since the password did'nt work for me (for some reason). I had a lot of authentication failure. After that attempting to log in to the server just timed out. I did the same at mediatemple (which used to work before with sftp) and put in wrong password and now trying to ssh (or even SFTP) gives me timeout error. So some kind of security feature is preventing me from trying too many times to log in, either from my side or from the server side. Any idea what it could be? TRaceroute and ping works on the ips. I am using a zyxel wimax modem (max-206m1r - if that's relevent) c:\Program Files (x86)\OpenSSH\bin>ssh.exe [email protected] ssh: connect to host 109.169.7.136 port 22: Connection timed out c:\Program Files (x86)\OpenSSH\bin>ssh.exe [email protected] ssh: connect to host 109.169.7.131 port 22: Connection timed out c:\Program Files (x86)\OpenSSH\bin>ssh.exe [email protected] ssh: connect to host 87.117.249.227 port 22: Connection timed out c:\Program Files (x86)\OpenSSH\bin>ssh.exe [email protected] -vv OpenSSH_5.6p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Reading configuration data /etc/ssh_config debug2: ssh_connect: needpriv 0 debug1: Connecting to 87.117.249.227 [87.117.249.227] port 22. debug1: connect to address 87.117.249.227 port 22: Connection timed out ssh: connect to host 87.117.249.227 port 22: Connection timed out c:\Program Files (x86)\OpenSSH\bin>ssh.exe s122797.gridserver.com Could not create directory '/home/pavs/.ssh'. The authenticity of host 's122797.gridserver.com (205.186.175.110)' can't be est ablished. RSA key fingerprint is 33:24:1e:38:bc:fd:75:02:81:d8:39:42:16:f6:f6:ff. Are you sure you want to continue connecting (yes/no)? yes Failed to add the host to the list of known hosts (/home/pavs/.ssh/known_hosts). Password: Password: Password: [email protected]'s password: Permission denied, please try again. [email protected]'s password: Permission denied, please try again. [email protected]'s password: Received disconnect from 205.186.175.110: 2: Too many authentication failures fo r pavs c:\Program Files (x86)\OpenSSH\bin>ssh.exe s122797.gridserver.com ssh: connect to host s122797.gridserver.com port 22: Connection timed out c:\Program Files (x86)\OpenSSH\bin>ssh.exe s122797.gridserver.com ssh: connect to host s122797.gridserver.com port 22: Connection timed out

    Read the article

  • Windows doesn't get access to internet though linux easily does

    - by flashnik
    We have a very interesting problem. The network is configured in this way: internet is connected to Trendnet switch TS DHCP server at 192.168.0.1 running on Ubuntu (S) is connected to internet switch DNS is also configured on 192.168.0.1 on S D-Link Wi-Fi boosters are connected to switch TS PCs use D-Link PCI-E Wi-Fi cards to get access to network PCs have both Ubuntu and Windows 7 There are about 40 PCs. When PC is booted to Ubuntu it easily gets access to internet. But when it's booted to Windows 7, it gets a valid IP-address, but doesn't get access to internet. The address, mask, DNS, GW-address are totally the same as when it's booted under Ubuntu. The S is reacheble and pingable. Sometimes when we are lucky the PC gets access to Internet, but after rebooting it can lose it. When PC under Windows has access, it has totally the same settings as when it doesn't. What can be done? UPDATE I shared a dropbox with 2 captures of traffic. Ping.pcap is a capture of pinging 8.8.8.8. And google-browser.pcap is a capture of opening a google.com in a browser, both of them are in tcpdump formats and made by Wireshark on Win PC. The MAC of Win PC ends on b7:63 and IP is 192.168.0.130. UPDATE2 This is ifconfig output from Ubuntu Server eth0 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8d inet addr:193.200.211.74 Bcast:193.200.211.78 Mask:255.255.255.0 inet6 addr: fe80::21e:67ff:fe13:d58d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:196284 errors:0 dropped:44 overruns:0 frame:0 TX packets:190682 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:158032255 (158.0 MB) TX bytes:156441225 (156.4 MB) Interrupt:19 Memory:c1400000-c1420000 eth0:2 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8d inet addr:192.168.0.1 Bcast:192.168.0.254 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Memory:c1400000-c1420000 eth1 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8c UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 Memory:c1300000-c1320000 nslookup from Win results in DNS request timeout, nbtstat in 'not found'.

    Read the article

  • First time installing Linux/Apache - uanble to connect

    - by bob
    I's my first time installing Linux/Apache. I loaded CentOS and LAMPP on a machine attached to a LAN. Turned off http and mysql (because I didn't want conflict with LLAMPP) chkconfig httpd off chkconfig mysqld off then successfully LAMPP started with /opt/lampp/lampp start Starting XAMPP for Linux 1.7.3a... XAMPP: Starting Apache with SSL (and PHP5)... XAMPP: Starting MySQL... XAMPP: Starting ProFTPD... XAMPP for Linux started. Problem: Unable to connect - Firefox can't establish a connection to the server at 179.16.51.36. I need some pointers as to where to look next. No errors in error_log file (just some warnings) I can ping server. httpd.conf looks like this: ServerRoot "/opt/lampp" Listen 80 ServerAdmin [email protected] ServerName 179.16.51.36 DocumentRoot "/opt/lampp/htdocs" <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory "/opt/lampp/htdocs"> Options Indexes FollowSymLinks ExecCGI Includes Order allow,deny Allow from all </Directory> ErrorLog logs/error_log LogLevel warn <IfModule log_config_module> LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %b" common <IfModule logio_module> LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\" %I %O" combinedio </IfModule> CustomLog logs/access_log common </IfModule> <IfModule alias_module> ScriptAlias /cgi-bin/ "/opt/lampp/cgi-bin/" </IfModule> <IfModule cgid_module> </IfModule> <Directory "/opt/lampp/cgi-bin"> AllowOverride None Options None Order allow,deny Allow from all </Directory> DefaultType text/plain <IfModule mime_module> TypesConfig etc/mime.types AddType application/x-compress .Z AddType application/x-gzip .gz .tgz AddHandler cgi-script .cgi .pl AddType text/html .shtml AddOutputFilter INCLUDES .shtml </IfModule> EnableMMAP off EnableSendfile off

    Read the article

  • Looking for a new, free firewall (Sunbelt has a huge hole)

    - by Jason
    I've been using Sunbelt Personal Firewall v. 4.5 (previously Kerio). I've discovered that blocking Firefox connections in the configuration doesn't stop EXISTING Firefox connections. (See my post here yesterday http://superuser.com/questions/132625/sunbelt-firewall-4-5-wont-block-firefox) The "stop all traffic" may work on existing connections - but I'm done testing, as I need to be able to be selective, at any time. I was using the free version, so the "web filtering" option quit working after some time (mostly blocking ads and popups), but I didn't use that anyway. I used the last free version of Kerio before finally having to go to Sunbelt, because Kerio had an unfixed bug where you'd eventually get the BSOD and have to reset Kerio's configuration and start over (configure everything again). So I'm looking for a new Firewall. I don't like ZoneAlarm at all (no offense to all it's users that may be here - personal taste). I need the following: (Sunbelt has all these, except *) - 1. Be able to block in/out to localhost (trusted)/internet selectively for each application with a click (so there's 4 click boxes for each application) [*that effects everything immediately, regardless of what's already connected]. When a new application attempts a connection, you get an allow/deny/remember windows. - 2. Be able to easily set up filter rules for 'individual application'/'all applications,' by protocol, port/address (range), local, remote, in, out. [*Adding a filter rule also doesn't block existing connections in Sunbelt. That needs to work too.] - 3. Have an easy-to-get-to way to "stop all traffic" (like a right click option on the running icon in the task bar). - 4. Be able to set trusted/internet in/out block/allowed (4 things per item) for each of IGMP, ping, DNS, DHCP, VPN, and broadcasts. - 5. Define locahost as trusted/untrusted, define adapter connections as trusted/untrusted. - 6. Block incoming connetions during boot-up and shutdown. - 7. Show existing connections, including local & remote ip/port, protocol, current speed, total bytes transferred, and local ports opened for Listening. - 8. An Intrusion Prevention System which blocks (optionally select each one) known intrustions (long list). - 9. Block/allow applications from starting other applications (deny/allow/remember window). Wish list: A way of knowing what svchost.exe is doing - who is actually using it/calling it. I allowed it for localhost, and selectively allowed it for internet each time the allow/deny window came up. Thanks for any help/suggestions. (I'm using Windows XP SP3.)

    Read the article

  • Trying to get DNS services running on Windows Server 2008 R2, what am I getting wrong ?

    - by LaserBeak
    Ok, So I am basically trying to get a home server pc up that will provide Domain name services, act as Mail server and web server. I have one static IP, well it's not officially static but hasn't changed in two years so I'll call it static. I have done the following: Configured router NAT/virtual port forward UDP/TCP port 53 to the internal IP of my server 192.168.1.16, in adapter settings specified the manual settings: 192.168.1.16 IP, gateway 192.168.1.1, Subnet: 255.255.255.0 and loopback DNS: 127.0.0.1 Using my public my public IP Checked using http://www.canyouseeme.org/ that port 53 is open and is not being blocked by my ISP. It can see services on this port. Registered Domain name (mydomain.com.au) Updated whois database through the domain registrars site and registered NameServer names: ns0.mydomain.com.au and ns2.mydomain.com.au, both have been associated with my single public IP. (Waited 24 hours) Update the nameserver for mydomain.com.au: primary ns0.mydomain.com.au secondary: ns2.mydomain.com.au (waited 24+ hours) Installed Server 2008 R2, install web server role and DNS role. Webserver works when I enter my public IP into browser of any PC/mobile, get IIS7 welcome page. In DNS server: Created new forward lookup zone: ; ; Database file mydoman.com.au.dns for mydomain.com.au zone. ; Zone version: 10 ; @ IN SOA mydomain.com.au. mydomain.testdomain.com. ( 10 ; serial number 900 ; refresh 600 ; retry 86400 ; expire 3600 ) ; default TTL ; ; Zone NS records ; @ NS ns0.mydomain.com.au. @ NS ns1.mydomain.com.au. ; ; Zone records ; @ A 192.168.1.16 www A 192.168.1.16 The Domain name services will however not work, the whois database updated with ns0.mydomain.com.au etc. but when I type in my site name www.mydomain.com.au from an external machine it will not open site and I can't even ping it (Can't find host) When I check the ns0.mydomain.com.au NS record using a tool Like: http://www.squish.net/dnscheck/ I get: Security: Server ns0.mydomain.com.au (XXX.XXX.XXX.XX <- my public IP) is recursive Domain exists but there is no such record Any ideas, thanks...

    Read the article

  • Ubuntu 11.10 firewall/gateway - no client internet access

    - by Siriss
    I have read many other posts but cannot figure this out. eth0 is my external connected to a Comcast modem. The server has internet access with no issues. eth1 is internal and running DHCP for the clients. I have DHCP working just fine, all my clients can get an IP and ping the server but they cannot access the internet. I am using ISC-DHCP-SERVER and have set /etc/default/isc-dhcp-server to INTERFACE="eht1" Here is my dhcpd.conf file located in /etc/dhcp/dhcpd.conf ddns-update-style interim; ignore client-updates; subnet 10.0.10.0 netmask 255.255.255.0 { range 10.0.10.10 10.0.10.200; option routers 10.0.10.2; option subnet-mask 255.255.255.0; option domain-name-servers 208.67.222.222, 208.67.220.220; #OpenDNS # option domain-name "example.com"; default-lease-time 21600; max-lease-time 43200; authoritative; } I have made the *net.ipv4.ip_forward=1* change in /etc/sysctl.conf here is my interfaces file: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp iface eth1 inet static address 10.0.10.2 netmask 255.255.255.0 network 10.0.10.0 auto eth1 And finally- here is my iptables.conf file: # Firewall configuration written by system-config-firewall # Manual customization of this file is not recommended. *nat :PREROUTING ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] -A POSTROUTING -s 10.0.10.0/24 -o eth0 -j MASQUERADE #-A PREROUTING -i eth0 -p tcp --dport 59668 -j DNAT --to-destination 10.0.10.2:59668 COMMIT *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -i eth1 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 22 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 80 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 443 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 53 -j ACCEPT -A INPUT -m state --state NEW -m udp -p udp --dport 53 -j ACCEPT -A FORWARD -s 10.0.10.0/24 -o eth0 -j ACCEPT -A FORWARD -d 10.0.10.0/24 -m state --state ESTABLISHED,RELATED -i eth0 -j ACCEPT -A FORWARD -p icmp -j ACCEPT -A FORWARD -i lo -j ACCEPT -A FORWARD -i eth1 -j ACCEPT #-A FORWARD -i eth0 -m state --state NEW -m tcp -p tcp -d 10.0.10.2 --dport 59668 -j ACCEPT -A INPUT -j REJECT --reject-with icmp-host-prohibited -A FORWARD -j REJECT --reject-with icmp-host-prohibited COMMIT I am completely stuck. I cannot figure out why the clients cannot access the internet. Am I missing a service? Is a service not running? Any help would be greatly appreciated. I tried to be as thorough as possible but please let me know if I have missed something. Thank you!

    Read the article

  • All internet requests in Windows time out

    - by Brandon
    So, I've run into a very strange problem with my home wireless network. Previously, at seemingly random times, the router seemed to disconnect all wireless hosts and cause all of the wired hosts to have a "limited connection" according to windows. In order to fix this, I had to unplug all of the wired hosts from the router, unplug the modem from the router, and power cycle the router. This seemed to solve the problem for a while until the exact same thing happened a day later and I had to go through the same process again. That's where I noticed something weird happening. There was one wireless host (a Windows Vista laptop) that seemed to be causing the router to disconnect the other hosts whenever it connected. When this happened, only that laptop was able to use the wireless from the router. When this happened, I disconnected it from the wireless (by disabling the wireless adapter) then reconnected it (by re-enabling it) and now it, like the other hosts, couldn't connect. I've never really seen anything this strange happen on our network before. So, I restored the router to factory settings and the problem seems to have vanished except one crucial problem. There's another host (a Windows 7 laptop) that was perfectly able to connect before all of the router issues and even in between the crashing and power-cycling events but now says its connected and says it's able to reach the Internet, but all requests time out. In any browser I've tried, the tab says connecting to [site]... for a solid minute and then tells me the request timed out. When I try to ping google.com in cmd it also says request timed out. In frustration, I booted into a dual-boot Ubuntu installation on the Windows 7 host and the connection works fine, to my surprise, as ubuntu is where I am now typing this rather long question. I haven't looked through the event log in windows but will post anything I find in an edit I haven't tried connecting (in Windows 7) to any other wireless network, since The fact that it works in Ubuntu suggests its Windows and not the router but I didn't change any wireless settings in windows before it being able to reach the Internet and not. Does anyone have any clue what could have happened. I opened to buying another router as this one is almost a year old :) but I would like to know whats going on here. Thanks in Advance! P.S. Sorry for how long my question is, I'm a little anxious (:

    Read the article

  • RDP exits immediately after connecting to Windows Server 2008 R2

    - by carpat
    Background: I recently got a Windows cloud VPS server. I don't have much experience with server admin (I'm a programmer), and what little I do have is with linux servers. Ever since getting the server I've been having issues with RDP. I can connect about two or three times, after which point I can't connect until one of the tech guys "fixes" it (see below). When I connect, I can stay connected for hours with no problem. When the problem connecting starts, the first time I try to log in, the remote desktop window pops up, starts connecting, and then exits with "Your Remote Desktop session has ended". After that, for about 10-20 minutes if I try to connect again, the connections times out with Remote Desktop can't connect to the computer for one of these reasons: 1) Remote access on the server is not enabled 2) The remote computer is turned off 3) The remote computer is not available on the network then goes back to connecting once and immediately disconnecting. All of the updates are installed. The firewall has been correctly configured to let RDP traffic through. The remote setting is "Allow connections from computers running any version of Remote Desktop". I tried creating a second user, and when I can't connect, I can't connect to that user either. I've tried both soft and hard reboots, neither of which help. I've tried connecting from two different computers (both running Windows 7) from two different networks (work and home), and the behavior is the same. Everything else on the server continues to run fine (IIS-served http pages, Tomcat-served java pages, svn, ping). The "fix" that the tech guys supply is simply logging into the console on their end, after which point I can connnect 2 or 3 times again. The event viewer on the server has "authentication failure" (or something similar) events generated when I attempt to log in and can't. I can't get to the actual event at the moment as I'm currently in the can't connect stage, and waiting for the techs to log in. But when I searched for the event earlier this morning I couldn't find anything useful. Can anyone help?

    Read the article

  • Reliable access to Internet but not local network (not DNS or proxy issues)

    - by Ian Goldby
    I'm looking for help with a Vista Home Premium laptop that has trouble accessing any resource on our home network, but accesses the Internet just fine. The set-up is this: The Vista laptop and a MacBook Pro connect wirelessly to the router-modem. A Synology DS212j NAS drive has a wired connection to the router-modem. Devices on the local network are always referred to by IP address, so this cannot be a DNS issue. The MacBook Pro connects reliably to the NA via AFP (network shared folders), SMB (network shared folders) and HTTP. The Vista laptop connects to and browses sites on the Internet without any problems. It can log into the NAS via SMB and list the shared folders (so there is nothing wrong with the log-in credentials), but when it tries to open any of the folders Explorer just hangs with the spinning cursor for several minutes and then says "\192.168.1.64\shared\Photos is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions. The specified network name is no longer available." It can ping the NAS successfully. If I try to open the NAS drive's web interface, the browser just hangs. This is the same with IE, Firefox and Chrome. (There is no proxy.) I can log into the NAS drive with FTP and navigate directories, but when I try to list the contents of a directory with more than a handful of entries, the ftp client hangs. I set up a website on the MacBook. The Vista laptop was able to load some of the pages, but loading any of the images was very hit and miss. Images embedded in HTML pages never worked no matter how many times I reloaded the page, but when I linked directly to the image it did load (though several attempts were sometimes needed). I tried all of this with the Windows Firewall turned off, and with AVG turned off. That made no difference. I'd really appreciate any suggestions anyone can make. The fact that the Vista laptop has trouble with HTTP and FTP as well as SMB connections suggests to me that this is a problem at the TCP level or below. But don't forget it accesses sites outside the LAN with no problems.

    Read the article

  • SIGINT and SIGTSTP ignored by most common applications

    - by Vašek Potocek
    After the last upgrade to my Fedora, a strange behaviour started occurring in X terminal applications. I can't seem to stop any process using Ctrl+C, it just results in printing ^C to the console. Similarly, Ctrl+Z prints ^Z and the process goes on. Both work well in non-graphical virtual consoles. I checked stty -a and it seems perfectly normal: speed 38400 baud; rows 24; columns 80; line = 0; intr = ^C; quit = ^\; erase = ^?; kill = ^U; eof = ^D; eol = M-^?; eol2 = M-^?; swtch = M-^?; start = ^Q; stop = ^S; susp = ^Z; rprnt = ^R; werase = ^W; lnext = ^V; flush = ^O; min = 1; time = 0; -parenb -parodd cs8 hupcl -cstopb cread -clocal -crtscts -ignbrk brkint -ignpar -parmrk -inpck -istrip -inlcr -igncr icrnl ixon -ixoff -iuclc ixany imaxbel iutf8 opost -olcuc -ocrnl onlcr -onocr -onlret -ofill -ofdel nl0 cr0 tab0 bs0 vt0 ff0 isig icanon iexten echo echoe echok -echonl -noflsh -xcase -tostop -echoprt echoctl echoke This is independent of the terminal (gnome-terminal, XFCE4 terminal, xterm). I later noticed that it may not be caused by the terminal at all: INT or TSTP sent directly to the respective process are ignored, too. This comprises various applications I used to terminate using Ctrl+C on a regular basis (and which often don't have any better means of exiting): cat, find, tail -f, java, ping, mplayer when stuck on a broken file... Even bash ignores Ctrl+C when I want to break a command line I have been entering and then changed my mind (no ^C is printed in this case). I need to delete it character by character (of which there may be hundreds if filename completion has been used) or intentionally run the unwanted command. Strangely enough, vim does recognize Ctrl+C—just to say its "use :quit", of course. This is extremely annoying and prevents me from working efficiently. Everything had been working until lately, maybe a week ago or so. I can not find any possible causes in Google, perhaps I'm trying wrong search terms or misidentifying the main problem. What could be it and how could I revert the standard behaviour, please? Update Ctrl+Z works sometimes. It seems that in the very first terminal I launch after logging in it stops the running command but stops working after that.

    Read the article

  • VPN Connection Causes Internal LAN Connection Loss with Server

    - by sleepisfortheweak
    I've tried configuring basic PPTP VPN at my small business using a number of different tutorials. As far as I can tell, the actual VPN connection worked fine, but upon connecting a client, the Server 'disappears' from the internal LAN. The RRAS service must be stopped before the connection is restored. My Setup: The network is simply a DSL Gateway/Router to the outside functioning as NAT/Firewall/DHCP. The server is a Win Server 2008 machine at fixed IP 192.168.1.200. The server has 1 NIC, so I used the 'custom' option when configuring RRAS. The RRAS settings should be default except that I've disabled ports for connection types I'm not using and reduced PPTP ports to 10. I've also created an address pool and disabled DHCP packet forwarding. The server only functions as a File Share and now a VPN Server. Local LAN computers all have mapped network shares to the server authenticated based on Local User/Group setup on the server. The Problem: The moment a client connects through VPN, the server 'disappears' from the local network. All mapped drives disconnect and there is no response to a ping 192.168.1.200. Even if the client disconnects, the server does not re-appear at that address until the RRAS service is stopped. I've Tried: Using an Address Pool inside and outside the local subnet. Using DCHP Relay Checking Inbound/Outbound filters (none enabled) The fact that nothing I've tried has had any effect, and that I can connect and successfully obtain an IP tells me that it's something more fundamental I'm missing. My gut tells me that it's something to do with the second IP address added by the VPN client somehow taking over the interface or traffic from the local LAN accidently getting routed to the VPN client instead of handled at the server once RRAS has become 'active' when a client connects. Hopefully this may be obvious to someone with real IT experience. I've been doing this a while and almost never been stumped. I'm starting to think it might actually be something tricky since my setup is pretty basic yet refuses to work. I'll be happy to include more info if this doesn't ring any bells right away for anyone. Thanks

    Read the article

  • MySQL performance over a (local) network much slower than I would expect

    - by user15241
    MySQL queries in my production environment are taking much longer than I would expect them too. The site in question is a fairly large Drupal site, with many modules installed. The webserver (Nginx) and database server (mysql) are hosted on separated machines, connected by a 100mbps LAN connection (hosted by Rackspace). I have the exact same site running on my laptop for development. Obviously, on my laptop, the webserver and database server are on the same box. Here are the results of my database query times: Production: Executed 291 queries in 320.33 milliseconds. (homepage) Executed 517 queries in 999.81 milliseconds. (content page) Development: Executed 316 queries in 46.28 milliseconds. (homepage) Executed 586 queries in 79.09 milliseconds. (content page) As can clearly be seen from these results, the time involved with querying the MySQL database is much shorter on my laptop, where the MySQL server is running on the same database as the web server. Why is this?! One factor must be the network latency. On average, a round trip from from the webserver to the database server takes 0.16ms (shown by ping). That must be added to every singe MySQL query. So, taking the content page example above, where there are 517 queries executed. Network latency alone will add 82ms to the total query time. However, that doesn't account for the difference I am seeing (79ms on my laptop vs 999ms on the production boxes). What other factors should I be looking at? I had thought about upgrading the NIC to a gigabit connection, but clearly there is something else involved. I have run the MySQL performance tuning script from http://www.day32.com/MySQL/ and it tells me that my database server is configured well (better than my laptop apparently). The only problem reported is "Of 4394 temp tables, 48% were created on disk". This is true in both environments and in the production environment I have even tried increasing max_heap_table_size and Current tmp_table_size to 1GB, with no change (I think this is because I have some BLOB and TEXT columns).

    Read the article

  • VLAN issues between linux kernels 2.6 / 3.3 in an ESX / Cisco environment

    - by David Griffith
    I shall attempt to explain an issue I have encountered - I have a VM running on esx 4.1 with an interface connected to VLAN800 via an access port on a cisco 3750. It runs linux - kernel 2.6.24, and has about 5 to 10 Mbit of chatter on 10.10.0.0/16 and various multicast addresses to look after. I needed to isolate certain devices from certain other devices on the network, with all of them having to talk to that one VM. No, the address space can't be separated, nor can the networks be easily vlan'd apart. The software on the VM listens to one interface only. Private vlans appear to be the way to go. So as a test, I built a bridge on the VM that globs together the vlans as needed. All good, everything works as expected. But occasionally (sigh) there's some latency that trips up a couple of profinet devices on the network because, you know, you're not really supposed to trunk real-time protocols around the place willy-nilly. I shift it to our test/backup server - works nicely, but I don't want it to be running on the test server as we muck around with that a lot. So I says to myself, "I'll put it on a new VM for testing and tweaking." I download a small linux distro with kernel 3.3, and install as a new VM with a the vlans as separate interfaces for testing. I power up the testing VM - ok. I bring up all the separate interfaces - ok. I can ping the production VM, see all sorts of traffic going past with tshark, etc. I build a bridge and put the primary vlan on it - the production VM running 2.6 immediately loses its multicast traffic - Unicast is fine. (?) I shut down the bridge - still no multicast traffic (!?) I power-cycle the production VM(!?!?) - multicast traffic returns. I trunk everything into the testing VM and create vlan interfaces under linux instead - same result, as soon as I start the bridge.... no multicast on the production VM. Ok, so I take a break and leave things alone. I decide to play with a couple of ubiquiti bullet radios - I'm testing various firmware as a side project. I flash a radio with Open-wrt-12.09. I enable a trunk on a port on a cisco on our network so I can muck around with multiple vlans and SSIDs I power up the radio and connect - ok. I create a vlan interface from the trunk.... the same vlan as the production VM wayyyyy over there, three cisco routers away. Ok. I bridge the vlan interface to the wifi interface and immediately get a phone call. The production VM has (suprise!) lost its multicast traffic. Again, nothing comes back until I power-cycle the VM. What the hell is going on?

    Read the article

  • Why is Windows 7 not following all routes?

    - by GigabyteProductions
    My computer is connected to my secondary router that's running the 192.168.42.0/24 network and my computer also has a route that directs anything on that network to the router, but for anything on that network other than the router itself, it get's the ICMP response of Reply from 192.168.42.194: Destination host unreachable. (with 192.168.42.194 being my computer). Every other network works, like all of the internet, or addresses on my primary router like 192.168.1.*, just not on the 192.168.42.0/24 network... route print returns: IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.42.1 192.168.42.194 276 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.42.0 255.255.255.0 On-link 192.168.42.194 276 192.168.42.194 255.255.255.255 On-link 192.168.42.194 276 192.168.42.255 255.255.255.255 On-link 192.168.42.194 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.42.194 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.42.194 276 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 192.168.42.1 Default =========================================================================== The only time anything is supposed to send an ICMP Host Unreachable response is when there's no route to it, right? So, why is my own computer sending that to ping or tracert when I have the route of 192.168.42.0 with the mask of 255.255.255.0? An IP address of 192.168.42.2 surely fits into that route. If I explicitly add a route for the IP address i am trying to access, it works, like: route add 192.168.42.2 mask 255.255.255.255 192.168.42.1 (the 192.168.42.1 right after mask is gateway, or the device to send the packet to so it can route it further), but why wont it work for the implicit route that's automatically on the table? I disabled my firewall, too (I use Comodo if anyone thinks this still serves as a problem). I'v even tried explicitly adding the gateway of 192.168.42.1 to the 192.168.42.0/24 route instead of it routing through 0.0.0.0's gateway, which is what On-link does. but that didn't work either, so it's not a gateway specification problem. If the host was really unreachable, it would be the router's IP address (192.168.42.1) sending that to me... This network is all of my creation, so there's no problem such as an administrator locking me out, because i am the administrator.

    Read the article

  • Why is Linux choosing the wrong source ip address

    - by Scheintod
    and what to do to let it choose the right one? This all happens inside an OpenVZ container: The Host is Debian/Wheezy with Redhat/OpenVZ Kernel: root@mycl2:~# uname -a Linux mycl2 2.6.32-openvz-042stab081.5-amd64 #1 SMP Mon Sep 30 16:40:27 MSK 2013 x86_64 GNU/Linux The container has two (virtual) network interfaces. One in public and one in private address-space: root@mycl2:~# ifconfig lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:127.0.0.2 P-t-P:127.0.0.2 Bcast:0.0.0.0 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 RX packets:475 errors:0 dropped:0 overruns:0 frame:0 TX packets:775 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:32059 (31.3 KiB) TX bytes:56309 (54.9 KiB) venet0:0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:80.123.123.29 P-t-P:80.123.123.29 Bcast:80.123.123.29 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 venet0:1 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:10.0.1.29 P-t-P:10.0.1.29 Bcast:10.0.1.29 Mask:255.255.255.255 UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 The route to the private network is set manually: root@mycl2:~# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 venet0 0.0.0.0 0.0.0.0 0.0.0.0 U 0 0 0 venet0 Tring to ping others on the private network leads to the wrong source address been choosen: root@mycl2:~# ip route get 10.0.1.26 10.0.1.26 dev venet0 src 80.123.123.29 cache mtu 1500 advmss 1460 hoplimit 64 Why is this and what can I do about it? EDIT: If I create the route with (thanks to Joshua) ip route add 10.0.0.0/8 dev venet0 src 10.0.1.29 it is working. But according to man ip-route the src parameter should only set the source-ip if this route is chosen. But if this route is chosen then the source-ip would be that anyway.

    Read the article

  • Monitoring almost anything with BizTalk 360

    - by Michael Stephenson
    When you work in an integration environment it is common that you will find yourself in a situation where you integrate with some unusual applications or have some unusual dependencies. That is the nature of integration. When you work with BizTalk one of the common problems is that BizTalk often is the place where problems with applications you integrate with are highlighted and these external applications may have poor monitoring solutions. Fortunately if you are a working with a customer who uses BizTalk 360 then it contains a feature called the "Web Endpoint Manager". Typically the web endpoint manager is used to monitor web services that you integrate with and will ping them at appropriate times to make sure they return the expected HTTP status code. When you have an usual situation where you want to monitor something which is key to the success to your solution but you find yourself having to consider a significant custom solution to monitor the external dependency then the Web Endpoint Manager could be your friend. The endpoint manager monitors a url and checks for a certain status code. This means that you can create your own aspx web page and then make BizTalk 360 monitor this web page. Behind the web page you could write any code you wished. An example of this is architecture is shown in the below diagram.     In the custom web page you would implement some custom code to do whatever it is that you want to monitor. In the below code snippet you can see how the Page_Load default method is doing some kind of check then depending on the result of the check it returns a certain HTTP code. protected void Page_Load(object sender, EventArgs e) { var result = CheckSomething();   if (result == "Success") Response.StatusCode = 202; else if (result == "DatabaseError") Response.StatusCode = 510; else if (result == "SystemError") Response.StatusCode = 512; else Response.StatusCode = 513;   }   In BizTalk 360 you would go into the Monitor and Notify tab and then to BizTalk Environment which gives you access to the Web Endpoint Manager. You need an alarm setup which configures how the endpoint will be checked. I'm not going to go through the details of creating the alarm as this is already documented in the BizTalk 360 documentation. One point to note is that in the example I am using I setup a threshold alarm which means that the url is checked about every minute and if there is an error that persists for a period of time then the alarm will raise the alert notification. In my example I configured the alarm to fire if the error persisted for 3 minutes. The below picture shows accessing the endpoint manager.   In the web endpoint manager you would then configure your endpoint to monitor and the HTTP response code which indicates all is working fine. The below picture shows this. I now have my endpoint monitoring setup and BizTalk 360 should be checking my custom endpoint to see that it is available. If I wanted to manually sanity check that the endpoints I have registered are working fine then clicking the Refresh button will show if they are all good or not. If my custom ASP.net page which is checking my dependency gets a problem you will see in the endpoint manager that the status code does not match the expected return code and your endpoints will display in red and you can see the problem. The below picture shows this. If I use specific HTTP response codes for the errors the custom ASP.net page might encounter I can easily interpret these to know what the problem is. Using the alarms and notifications with BizTalk 360 it means when your endpoint goes into an error state you can easily configure email or SMS notifications from BizTalk 360 to tell you that your endpoint is having problems and you can use BizTalk 360 to help correlate what the problem is to allow you to investigate further. Below you can see the email which tells me my endpoint is not working.   When everything returns to normal you will see the status is now fixed and you will see a situation like below where you can see the WebEndpoints are now green and the return code matches what is expected.   Conclusion As you can see it is really easy to plug your own custom ASP.net page into the BizTalk 360 web endpoint monitoring feature. This extension then gives you the power to really extend the monitoring to almost anything you want as long as you can write some .net code to check that the dependency is available and working. It would be interesting to hear of any ideas people have around things they would monitor with this extension. More details on the end point monitor can be found on the following link: http://www.biztalk360.com/tour/monitoring_notifications

    Read the article

  • GlassFish Clustering with DCOM on Windows

    - by ByronNevins
    DCOM - Distributed COM, a Microsoft protocol for communicating with Windows machines. Why use DCOM? In GlassFish 3.1 SSH is used as the standard way to run commands on remote nodes for clustering.  It is very difficult for users to get SSH configured properly on Windows.  SSH does not come with Windows so we have to depend on third party tools.  And then the user is forced to install and configure these tools -- which can be tricky. DCOM is available on all supported platforms.  It is built-in to Windows. The idea is to use DCOM to communicate with remote Windows nodes.  This has the huge advantage that the user has to do minimal, if any, configuration on the Windows nodes. Implementation HighlightsTwo open Source Libraries have been added to GlassFish: Jcifs – a SAMBA implementation in Java J-interop – A Java implementation for making DCOM calls to remote Windows computers.   Note that any supported platform can use DCOM to work with Windows nodes -- not just Windows.E.g. you can have a Linux DAS work with Windows remote instances.All existing SSH commands now have a corresponding DCOM command – except for setup-ssh which isn’t needed for DCOM.  validate-dcom is an all new command. New DCOM Commands create-node-dcom delete-node-dcom install-node-dcom list-nodes-dcom ping-node-dcom uninstall-node-dcom update-node-dcom validate-dcom setup-local-dcom (This is only available via Update Center for GlassFish 3.1.2) These commands are in-place in the trunk (4.0).  And in the branch (3.1.2) Windows Configuration Challenges There are an infinite number of possible configurations of Windows if you look at it as a combination of main release, service-pack, special drivers, software, configuration etc.  Later versions of Windows err on the side of tightening security be default.  This means that the Windows host may need to have configuration changes made.These configuration changes mostly need to be made by the user.  setup-local-dcom will assist you in making required changes to the Windows Registry.  See the reference blogs for details. The validate-dcom Command validate-dcom is a crucial command.  It should be run before any other commands.  If it does not run successfully then there is no point in running other commands.The validate-dcom command must be used from a DAS machine to test a different Windows machine.  If  validate-dcom runs successfully you can be confident that all the DCOM commands will work.  Conversely, the opposite is also true:  If validate-dcom fails, then no DCOM commands will work. What validate-dcom does Verify that the remote host is not the local machine. Resolves the remote host name Checks that the remote DCOM port is being listened on (135, 139) Checks that the remote host’s File Sharing is enabled (port 445) It copies a file (a script) to the remote host to verify that SAMBA is working and authorization is correct It runs a script that it copied on-the-fly to the remote host. Tips and Tricks The bread and butter commands that use DCOM are existing commands like create-instance, start-instance etc.   All of the commands that have dcom in their name are for dealing with the actual nodes. The way the software works is to call asadmin.bat on the remote machine and run a command.  This means that you can track these commands easily on the remote machine with the usual tools.  E.g. using AS_LOGFILE, looking at log files, etc.  It’s easy to attach a debugger to the remote asadmin process, “just in time”, if necessary. How to debug the remote commands:Edit the asadmin.bat file that is in the glassfish/bin folder.  Use glassfish/lib/nadmin.bat in GlassFish 4.0+Add these options to the java call:-Xdebug -Xrunjdwp:transport=dt_socket,server=y,suspend=y,address=1234  Now if you run, say start-instance on DAS, you can attach your debugger, at your leisure, to the remote machines port 1234.  It will be running start-local-instance and patiently waiting for you to attach.

    Read the article

  • My Red Gate Experience

    - by Colin Rothwell
    I’m Colin, and I’ve been an intern working with Mike in publishing on Simple-Talk and SQLServerCentral for the past ten weeks. I’ve mostly been working “behind the scenes”, making improvements to the spam filtering, along with various other small tweaks. When I arrived at Red Gate, one of the first things Mike asked me was what I wanted to get out of the internship. It wasn’t a question I’d given a great deal of thought to, but my immediate response was the same as almost anybody: to support my growing family. Well, ok, not quite that, but money was certainly a motivator, along with simply making sure that I didn’t get bored over the summer. Three months is a long time to fill, and many of my friends end up getting bored, or worse, knitting obsessively. With the arrogance which seems fairly common among Cambridge people, I wasn’t expecting to really learn much here! In my mind, the part of the year where I am at Uni is the part where I learn things, whilst Red Gate would be an opportunity to apply what I’d learnt. Thankfully, the opposite is true: I’ve learnt a lot during my time here, and there has been a definite positive impact on the way I write code. The first thing I’ve really learnt is that test-driven development is, in general, a sensible way of working. Before coming, I didn’t really get it: how could you test something you hadn’t yet written? It didn’t make sense! My problem was seeing a test as having to test all the behaviour of a given function. Writing tests which test the bare minimum possible and building them up is a really good way of crystallising the direction the code needs to grow in, and ensures you never attempt to write too much code at time. One really good experience of this was early on in my internship when Mike and I were working on the query used to list active authors: I’d written something which I thought would do the trick, but by starting again using TDD we grew something which revealed that there were several subtle mistakes in the query I’d written. I’ve also been awakened to the value of pair programming. Whilst I could sort of see the point before coming, I also thought that it was impossible that two people would ever get more done at the same computer than if they were working separately. I still think that this is true for projects with pieces that developers can easily work on independently, and with developers who both know the codebase, but I’ve found that pair programming can be really good for learning a code base, and for building up small projects to the point where you can start working on separate components, as well as solving particularly difficult problems. Later on in my internship, for my down tools week project, I was working on adding Python support to Glimpse. Another intern and I we pair programmed the entire project, using ping pong pair programming as much as possible. One bonus that this brought which I wasn’t expecting was that I found myself less prone to distraction: with someone else peering over my shoulder, I didn’t have the ever-present temptation to open gmail, or facebook, or yammer, or twitter, or hacker news, or reddit, and so on, and so forth. I’m quite proud of this project: I think it’s some of the best code I’ve written. I’ve also been really won over to the value of descriptive variables names. In my pre-Red Gate life, as a lone-ranger style cowboy programmer, I’d developed a tendency towards laziness in variable names, sometimes abbreviating or, worse, using acronyms. I’ve swiftly realised that this is a bad idea when working with a team: saving a few key strokes is inevitably not worth it when it comes to reading code again in the future. Longer names also mean you can do away with a majority of comments. I appreciate that if you’ve come up with an O(n*log n) algorithm for something which seemed O(n^2), you probably want to explain how it works, but explaining what a variable name means is a big no no: it’s so very easy to change the behaviour of the code, whilst forgetting about the comments. Whilst at Red Gate, I took the opportunity to attend a code retreat, which really helped me to solidify all the things I’d learnt. To be completely free of any existing code base really lets you focus on best practises and think about how you write code. If you get a chance to go on a similar event, I’d highly recommend it! Cycling to Red Gate, I’ve also become much better at fitting inner tubes: if you’re struggling to get the tube out, or re-fit the tire, letting a bit of air out usually helps. I’ve also become quite a bit better at foosball and will miss having a foosball table! I’d like to finish off by saying thank you to everyone at Red Gate for having me. I’ve really enjoyed working with, and learning from, the team that brings you this web site. If you meet any of them, buy them a drink!

    Read the article

  • Rkhunter 122 suspect files; do I have a problem?

    - by user276166
    I am new to ubuntu. I am using Xfce Ubuntu 14.04 LTS. I have ran rkhunter a few weeks age and only got a few warnings. The forum said that they were normal. But, this time rkhunter reported 122 warnings. Please advise. casey@Shaman:~$ sudo rkhunter -c [ Rootkit Hunter version 1.4.0 ] Checking system commands... Performing 'strings' command checks Checking 'strings' command [ OK ] Performing 'shared libraries' checks Checking for preloading variables [ None found ] Checking for preloaded libraries [ None found ] Checking LD_LIBRARY_PATH variable [ Not found ] Performing file properties checks Checking for prerequisites [ Warning ] /usr/sbin/adduser [ Warning ] /usr/sbin/chroot [ Warning ] /usr/sbin/cron [ OK ] /usr/sbin/groupadd [ Warning ] /usr/sbin/groupdel [ Warning ] /usr/sbin/groupmod [ Warning ] /usr/sbin/grpck [ Warning ] /usr/sbin/nologin [ Warning ] /usr/sbin/pwck [ Warning ] /usr/sbin/rsyslogd [ Warning ] /usr/sbin/useradd [ Warning ] /usr/sbin/userdel [ Warning ] /usr/sbin/usermod [ Warning ] /usr/sbin/vipw [ Warning ] /usr/bin/awk [ Warning ] /usr/bin/basename [ Warning ] /usr/bin/chattr [ Warning ] /usr/bin/cut [ Warning ] /usr/bin/diff [ Warning ] /usr/bin/dirname [ Warning ] /usr/bin/dpkg [ Warning ] /usr/bin/dpkg-query [ Warning ] /usr/bin/du [ Warning ] /usr/bin/env [ Warning ] /usr/bin/file [ Warning ] /usr/bin/find [ Warning ] /usr/bin/GET [ Warning ] /usr/bin/groups [ Warning ] /usr/bin/head [ Warning ] /usr/bin/id [ Warning ] /usr/bin/killall [ OK ] /usr/bin/last [ Warning ] /usr/bin/lastlog [ Warning ] /usr/bin/ldd [ Warning ] /usr/bin/less [ OK ] /usr/bin/locate [ OK ] /usr/bin/logger [ Warning ] /usr/bin/lsattr [ Warning ] /usr/bin/lsof [ OK ] /usr/bin/mail [ OK ] /usr/bin/md5sum [ Warning ] /usr/bin/mlocate [ OK ] /usr/bin/newgrp [ Warning ] /usr/bin/passwd [ Warning ] /usr/bin/perl [ Warning ] /usr/bin/pgrep [ Warning ] /usr/bin/pkill [ Warning ] /usr/bin/pstree [ OK ] /usr/bin/rkhunter [ OK ] /usr/bin/rpm [ Warning ] /usr/bin/runcon [ Warning ] /usr/bin/sha1sum [ Warning ] /usr/bin/sha224sum [ Warning ] /usr/bin/sha256sum [ Warning ] /usr/bin/sha384sum [ Warning ] /usr/bin/sha512sum [ Warning ] /usr/bin/size [ Warning ] /usr/bin/sort [ Warning ] /usr/bin/stat [ Warning ] /usr/bin/strace [ Warning ] /usr/bin/strings [ Warning ] /usr/bin/sudo [ Warning ] /usr/bin/tail [ Warning ] /usr/bin/test [ Warning ] /usr/bin/top [ Warning ] /usr/bin/touch [ Warning ] /usr/bin/tr [ Warning ] /usr/bin/uniq [ Warning ] /usr/bin/users [ Warning ] /usr/bin/vmstat [ Warning ] /usr/bin/w [ Warning ] /usr/bin/watch [ Warning ] /usr/bin/wc [ Warning ] /usr/bin/wget [ Warning ] /usr/bin/whatis [ Warning ] /usr/bin/whereis [ Warning ] /usr/bin/which [ OK ] /usr/bin/who [ Warning ] /usr/bin/whoami [ Warning ] /usr/bin/unhide.rb [ Warning ] /usr/bin/mawk [ Warning ] /usr/bin/lwp-request [ Warning ] /usr/bin/heirloom-mailx [ OK ] /usr/bin/w.procps [ Warning ] /sbin/depmod [ Warning ] /sbin/fsck [ Warning ] /sbin/ifconfig [ Warning ] /sbin/ifdown [ Warning ] /sbin/ifup [ Warning ] /sbin/init [ Warning ] /sbin/insmod [ Warning ] /sbin/ip [ Warning ] /sbin/lsmod [ Warning ] /sbin/modinfo [ Warning ] /sbin/modprobe [ Warning ] /sbin/rmmod [ Warning ] /sbin/route [ Warning ] /sbin/runlevel [ Warning ] /sbin/sulogin [ Warning ] /sbin/sysctl [ Warning ] /bin/bash [ Warning ] /bin/cat [ Warning ] /bin/chmod [ Warning ] /bin/chown [ Warning ] /bin/cp [ Warning ] /bin/date [ Warning ] /bin/df [ Warning ] /bin/dmesg [ Warning ] /bin/echo [ Warning ] /bin/ed [ OK ] /bin/egrep [ Warning ] /bin/fgrep [ Warning ] /bin/fuser [ OK ] /bin/grep [ Warning ] /bin/ip [ Warning ] /bin/kill [ Warning ] /bin/less [ OK ] /bin/login [ Warning ] /bin/ls [ Warning ] /bin/lsmod [ Warning ] /bin/mktemp [ Warning ] /bin/more [ Warning ] /bin/mount [ Warning ] /bin/mv [ Warning ] /bin/netstat [ Warning ] /bin/ping [ Warning ] /bin/ps [ Warning ] /bin/pwd [ Warning ] /bin/readlink [ Warning ] /bin/sed [ Warning ] /bin/sh [ Warning ] /bin/su [ Warning ] /bin/touch [ Warning ] /bin/uname [ Warning ] /bin/which [ OK ] /bin/kmod [ Warning ] /bin/dash [ Warning ] [Press <ENTER> to continue] Checking for rootkits... Performing check of known rootkit files and directories 55808 Trojan - Variant A [ Not found ] ADM Worm [ Not found ] AjaKit Rootkit [ Not found ] Adore Rootkit [ Not found ] aPa Kit [ Not found ] Apache Worm [ Not found ] Ambient (ark) Rootkit [ Not found ] Balaur Rootkit [ Not found ] BeastKit Rootkit [ Not found ] beX2 Rootkit [ Not found ] BOBKit Rootkit [ Not found ] cb Rootkit [ Not found ] CiNIK Worm (Slapper.B variant) [ Not found ] Danny-Boy's Abuse Kit [ Not found ] Devil RootKit [ Not found ] Dica-Kit Rootkit [ Not found ] Dreams Rootkit [ Not found ] Duarawkz Rootkit [ Not found ] Enye LKM [ Not found ] Flea Linux Rootkit [ Not found ] Fu Rootkit [ Not found ] Fuck`it Rootkit [ Not found ] GasKit Rootkit [ Not found ] Heroin LKM [ Not found ] HjC Kit [ Not found ] ignoKit Rootkit [ Not found ] IntoXonia-NG Rootkit [ Not found ] Irix Rootkit [ Not found ] Jynx Rootkit [ Not found ] KBeast Rootkit [ Not found ] Kitko Rootkit [ Not found ] Knark Rootkit [ Not found ] ld-linuxv.so Rootkit [ Not found ] Li0n Worm [ Not found ] Lockit / LJK2 Rootkit [ Not found ] Mood-NT Rootkit [ Not found ] MRK Rootkit [ Not found ] Ni0 Rootkit [ Not found ] Ohhara Rootkit [ Not found ] Optic Kit (Tux) Worm [ Not found ] Oz Rootkit [ Not found ] Phalanx Rootkit [ Not found ] Phalanx2 Rootkit [ Not found ] Phalanx2 Rootkit (extended tests) [ Not found ] Portacelo Rootkit [ Not found ] R3dstorm Toolkit [ Not found ] RH-Sharpe's Rootkit [ Not found ] RSHA's Rootkit [ Not found ] Scalper Worm [ Not found ] Sebek LKM [ Not found ] Shutdown Rootkit [ Not found ] SHV4 Rootkit [ Not found ] SHV5 Rootkit [ Not found ] Sin Rootkit [ Not found ] Slapper Worm [ Not found ] Sneakin Rootkit [ Not found ] 'Spanish' Rootkit [ Not found ] Suckit Rootkit [ Not found ] Superkit Rootkit [ Not found ] TBD (Telnet BackDoor) [ Not found ] TeLeKiT Rootkit [ Not found ] T0rn Rootkit [ Not found ] trNkit Rootkit [ Not found ] Trojanit Kit [ Not found ] Tuxtendo Rootkit [ Not found ] URK Rootkit [ Not found ] Vampire Rootkit [ Not found ] VcKit Rootkit [ Not found ] Volc Rootkit [ Not found ] Xzibit Rootkit [ Not found ] zaRwT.KiT Rootkit [ Not found ] ZK Rootkit [ Not found ] [Press <ENTER> to continue] Performing additional rootkit checks Suckit Rookit additional checks [ OK ] Checking for possible rootkit files and directories [ None found ] Checking for possible rootkit strings [ None found ] Performing malware checks Checking running processes for suspicious files [ None found ] Checking for login backdoors [ None found ] Checking for suspicious directories [ None found ] Checking for sniffer log files [ None found ] Performing Linux specific checks Checking loaded kernel modules [ OK ] Checking kernel module names [ OK ] [Press <ENTER> to continue] Checking the network... Performing checks on the network ports Checking for backdoor ports [ None found ] Checking for hidden ports [ Skipped ] Performing checks on the network interfaces Checking for promiscuous interfaces [ None found ] Checking the local host... Performing system boot checks Checking for local host name [ Found ] Checking for system startup files [ Found ] Checking system startup files for malware [ None found ] Performing group and account checks Checking for passwd file [ Found ] Checking for root equivalent (UID 0) accounts [ None found ] Checking for passwordless accounts [ None found ] Checking for passwd file changes [ Warning ] Checking for group file changes [ Warning ] Checking root account shell history files [ None found ] Performing system configuration file checks Checking for SSH configuration file [ Not found ] Checking for running syslog daemon [ Found ] Checking for syslog configuration file [ Found ] Checking if syslog remote logging is allowed [ Not allowed ] Performing filesystem checks Checking /dev for suspicious file types [ Warning ] Checking for hidden files and directories [ Warning ] [Press <ENTER> to continue] System checks summary ===================== File properties checks... Required commands check failed Files checked: 137 Suspect files: 122 Rootkit checks... Rootkits checked : 291 Possible rootkits: 0 Applications checks... All checks skipped The system checks took: 5 minutes and 11 seconds All results have been written to the log file (/var/log/rkhunter.log)

    Read the article

  • Intel Centrino Wireless-N 1000 Again ! Ubuntu 13.04 x64

    - by vafa
    First I have to say that I tried everything written about this concept. The problem is that it stops working randomly in 3 main forms : 1 - sometimes it disconnect from wireless network and reconnect automatically 2 - sometimes it disconnect and wont connect no matter what (needs reboot) 3 - some times it's still connected but cannot ping or surf or whatever. I already tried disabling N mod using these commands : sudo modprobe -r iwlwifi modprobe iwlwifi 11n_disable=1 (or 0, whatever) it didn't help . these are the results of lspci, sudo lshw -C network, ifconfig, iwconfig, rfkill list when it disconnected and didn't connect till reboot : ifconfig : eth0 Link encap:Ethernet HWaddr c8:0a:a9:34:65:77 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:1563213476557380 errors:9379306629148050 dropped:3126435543049350 overruns:1563217771524675 frame:7816088857623375 TX packets:1563217771524675 errors:6252871086098700 dropped:0 overruns:1563217771524675 carrier:3126435543049350 collisions:7816088857623375 txqueuelen:1000 RX bytes:1563217771524675 (1.5 PB) TX bytes:1563217771524675 (1.5 PB) ham0 Link encap:Ethernet HWaddr 7a:79:19:a5:e4:93 inet addr:25.165.228.147 Bcast:25.255.255.255 Mask:255.0.0.0 inet6 addr: fe80::7879:19ff:fea5:e493/64 Scope:Link inet6 addr: 2620:9b::19a5:e493/96 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1404 Metric:1 RX packets:7743 errors:0 dropped:0 overruns:0 frame:0 TX packets:1250 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:665642 (665.6 KB) TX bytes:204056 (204.0 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:41138 errors:0 dropped:0 overruns:0 frame:0 TX packets:41138 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6420962 (6.4 MB) TX bytes:6420962 (6.4 MB) wlan0 Link encap:Ethernet HWaddr 00:1e:64:45:fb:70 inet6 addr: fe80::21e:64ff:fe45:fb70/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:286999 errors:0 dropped:0 overruns:0 frame:0 TX packets:226966 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:324386887 (324.3 MB) TX bytes:30674804 (30.6 MB) iwconfig : ham0 no wireless extensions. eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=14 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off sudo lshw -C network: *-network description: Wireless interface product: Centrino Wireless-N 1000 [Condor Peak] vendor: Intel Corporation physical id: 0 bus info: pci@0000:07:00.0 logical name: wlan0 version: 00 serial: 00:1e:64:45:fb:70 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.8.0-30-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bg resources: irq:46 memory:c0400000-c0401fff *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: c0 serial: c8:0a:a9:34:65:77 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.1-NAPI latency=0 link=no multicast=yes port=twisted pair resources: irq:47 memory:c0900000-c093ffff ioport:5000(size=128) *-network description: Ethernet interface physical id: 2 logical name: ham0 serial: 7a:79:19:a5:e4:93 size: 10Mbit/s capabilities: ethernet physical configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full ip=25.165.228.147 link=yes multicast=yes port=twisted pair speed=10Mbit/s lspci: 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port (rev 07) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03) 00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.3 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 01:00.0 VGA compatible controller: NVIDIA Corporation G98M [GeForce G 105M] (rev a1) 07:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000 [Condor Peak] 09:00.0 Ethernet controller: Qualcomm Atheros AR8131 Gigabit Ethernet (rev c0) rfkill list : 1: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no 2: acer-bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 9: phy0: Wireless LAN Soft blocked: no Hard blocked: no any help will be REALLLYYYY appreciated

    Read the article

  • Can't connect to local IP address on OSX

    - by Alex Worden
    I'm trying to connect to a webserver that's running on my mac OSX 1.6. I'm able to connect to it locally using http://127.0.0.1:8888/myapp but when I attempt to connect to it using my machine's local IP address (http://192.168.1.15:8888/myapp IP shown below) from the same machine (or another on the network) I cannot connect. I can ping the LAN IP address. I've tried adding IP forwarding to my router for port 8888 but it didn't help. I've checked and the OSX firewall is disabled Can anyone suggest what else is blocking the connection? Here's what I get when I run ifconfig: ~ :ifconfig lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 inet6 ::1 prefixlen 128 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1 inet 127.0.0.1 netmask 0xff000000 gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280 stf0: flags=0<> mtu 1280 en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 ether 00:1f:5b:e8:16:4d media: autoselect status: inactive supported media: autoselect 10baseT/UTP <half-duplex> 10baseT/UTP <full-duplex> 10baseT/UTP <full-duplex,hw-loopback> 10baseT/UTP <full-duplex,flow-control> 100baseTX <half-duplex> 100baseTX <full-duplex> 100baseTX <full-duplex,hw-loopback> 100baseTX <full-duplex,flow-control> 1000baseT <full-duplex> 1000baseT <full-duplex,hw-loopback> 1000baseT <full-duplex,flow-control> none en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 inet6 fe80::21e:c2ff:febf:4809%en1 prefixlen 64 scopeid 0x5 inet 192.168.1.15 netmask 0xffffff00 broadcast 192.168.1.255 ether 00:1e:c2:bf:48:09 media: autoselect status: active supported media: autoselect fw0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 4078 lladdr 00:1f:5b:ff:fe:2b:b3:3c media: autoselect <full-duplex> status: inactive supported media: autoselect <full-duplex> en5: flags=8822<BROADCAST,SMART,SIMPLEX,MULTICAST> mtu 1500 ether 00:1e:c2:8e:0f:45 media: autoselect status: inactive supported media: none autoselect 10baseT/UTP <half-duplex> en2: flags=8922<BROADCAST,SMART,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether 00:1c:42:00:00:00 media: autoselect status: inactive supported media: autoselect en3: flags=8922<BROADCAST,SMART,PROMISC,SIMPLEX,MULTICAST> mtu 1500 ether 00:1c:42:00:00:01 media: autoselect status: inactive supported media: autoselect

    Read the article

  • MSDTC - Communication with the underlying transaction manager has failed (Firewall open, MSDTC netwo

    - by SocialAddict
    I'm having problems with my ASP.NET web forms system. It worked on our test server but now we are putting it live one of the servers is within a DMZ and the SQL server is outside of that (on our network still though - although a different subnet) I have open up the firewall completely between these two boxes to see if that was the issue and it still gives the error message "Communication with the underlying transaction manager has failed" whenever we try and use the "TransactionScope". We can access the data for retrieval it's just transactions that break it. We have also used msdtc ping to test the connection and with the amendments on the firewall that pings successfully, but the same error occurs! How do i resolve this error? Any help would be great as we have a system to go live today. Panic :) Edit: I have created a more straightforward test page with a transaction as below and this works fine. Could a nested transaction cause this kind of error and if so why would this only cause an issue when using a live box in a dmz with a firewall? AuditRepository auditRepository = new AuditRepository(); try { using (TransactionScope scope = new TransactionScope()) { auditRepository.Add(DateTime.Now, 1, "TEST-TRANSACTIONS#1", 1); auditRepository.Save(); auditRepository.Add(DateTime.Now, 1, "TEST-TRANSACTIONS#2", 1); auditRepository.Save(); scope.Complete(); } } catch (Exception ex) { Response.Write("Test Error For Transaction: " + ex.Message + "<br />" + ex.StackTrace); } This is the ErrorStack we are getting when the problem occurs: at System.Transactions.TransactionInterop.GetOletxTransactionFromTransmitterPropigationToken(Byte[] propagationToken) at System.Transactions.TransactionStatePSPEOperation.PSPEPromote(InternalTransaction tx) at System.Transactions.TransactionStateDelegatedBase.EnterState(InternalTransaction tx) at System.Transactions.EnlistableStates.Promote(InternalTransaction tx) at System.Transactions.Transaction.Promote() at System.Transactions.TransactionInterop.ConvertToOletxTransaction(Transaction transaction) at System.Transactions.TransactionInterop.GetExportCookie(Transaction transaction, Byte[] whereabouts) at System.Data.SqlClient.SqlInternalConnection.GetTransactionCookie(Transaction transaction, Byte[] whereAbouts) at System.Data.SqlClient.SqlInternalConnection.EnlistNonNull(Transaction tx) at System.Data.SqlClient.SqlInternalConnection.Enlist(Transaction tx) at System.Data.SqlClient.SqlInternalConnectionTds.Activate(Transaction transaction) at System.Data.ProviderBase.DbConnectionInternal.ActivateConnection(Transaction transaction) at System.Data.ProviderBase.DbConnectionPool.GetConnection(DbConnection owningObject) at System.Data.ProviderBase.DbConnectionFactory.GetConnection(DbConnection owningConnection) at System.Data.ProviderBase.DbConnectionClosed.OpenConnection(DbConnection outerConnection, DbConnectionFactory connectionFactory) at System.Data.SqlClient.SqlConnection.Open() at System.Data.Linq.SqlClient.SqlConnectionManager.UseConnection(IConnectionUser user) at System.Data.Linq.SqlClient.SqlProvider.get_IsSqlCe() at System.Data.Linq.SqlClient.SqlProvider.InitializeProviderMode() at System.Data.Linq.SqlClient.SqlProvider.System.Data.Linq.Provider.IProvider.Execute(Expression query) at System.Data.Linq.ChangeDirector.StandardChangeDirector.DynamicInsert(TrackedObject item) at System.Data.Linq.ChangeDirector.StandardChangeDirector.Insert(TrackedObject item) at System.Data.Linq.ChangeProcessor.SubmitChanges(ConflictMode failureMode) at System.Data.Linq.DataContext.SubmitChanges(ConflictMode failureMode) at System.Data.Linq.DataContext.SubmitChanges() at RegBook.classes.DbBase.Save() at RegBook.usercontrols.BookingProcess.confirmBookingButton_Click(Object sender, EventArgs e)

    Read the article

  • EJB3 - using 2 persistence units within a transaction (Exception: Local transaction already has 1 no

    - by Sorcha
    I am trying to use 2 persistence units within the same transaction in a JEE application deployed on Glassfish. The 2 persistence units are defined in persistence.xml, as follows: <persistence-unit name="BeachWater"> <jta-data-source>jdbc/BeachWater</jta-data-source> ... <persistence-unit name="LIMS"> <jta-data-source>jdbc/BeachWaterLIMS</jta-data-source> ... These persistence units correspond to JDBC resources and connection pools which I had defined in Glassfish as follows (include one here as both are identical apart from names & database connection info): JDBC Resource: JNDI Name: jdbc/BeachWaterLIMS Pool Name: BEACHWATER_LIMS Connection Pool: Name: BEACHWATER_LIMS Datasource Classname: com.microsoft.sqlserver.jdbc.SQLServerConnectionPoolDataSource Resource Type: javax.sql.ConnectionPoolDataSource There are 3 stateless session beans, LimsServiceBean, AnalysisServiceBean and AnalysisDataTransformationServiceBean. Here are the relevant snippets from LimsServiceBean: @PersistenceContext(unitName = "LIMS") EntityManager em; ... public ArrayList<Sample> getLatestLIMSData() { Query q = em.createNamedQuery("Sample.findBySubTypeStatus"); return new ArrayList<Sample>(q.getResultList()); } From AnalysisServiceBean: @PersistenceContext(unitName = "BeachWater") EntityManager em; ... public ArrayList<AnalysisType> getAllAnalysisTypes() { Query q = em.createNamedQuery("AnalysisType.findAll"); return new ArrayList<AnalysisType>(q.getResultList()); } And from AnalysisDataTransformationServiceBean: @EJB private AnalysisService analysisService; @EJB private LimsService limsService; public void transformData() { List<AnalysisType> analysisTypes = analysisService.getAllAnalysisTypes(); ArrayList<Sample> samples = limsService.getLatestLIMSData(); This call to limsService.getLatestLIMSData() caused the following exception: [exec] Caused by: javax.ejb.TransactionRolledbackLocalException: Exception thrown from bean; nested exception is: Exception [TOPLINK-4002] (Oracle TopLink Essentials - 2.1 (Build b60e-fcs (12/23/2008))): oracle.toplink.essentials.exceptions.DatabaseException [exec] Internal Exception: java.sql.SQLException: Error in allocating a connection. Cause: java.lang.IllegalStateException: Local transaction already has 1 non-XA Resource: cannot add more resources. Having consulted this page, http://msdn.microsoft.com/en-us/library/ms378484.aspx (among many others), I tried changing the definition of the connection pools to: Connection Pool: Name: BEACHWATER_LIMS Datasource Classname: com.microsoft.sqlserver.jdbc.SQLServerXADataSource Resource Type: javax.sql.XADataSource Ping via the Glassfish admin console succeeds, but call to analysisService.getAllAnalysisTypes() now throws an exception: Caused by: javax.ejb.TransactionRolledbackLocalException: Exception thrown from bean; nested exception is: Exception [TOPLINK-4002] (Oracle TopLink Essentials - 2.1 (Build b60e-fcs (12/23/2008))): oracle.toplink.essentials.exceptions.DatabaseException Internal Exception: java.sql.SQLException: Error in allocating a connection. Cause: javax.transaction.SystemException Any ideas?

    Read the article

  • Java Webservice java.lang.ClassCastException: org.apache.cxf.jaxws.ServiceImpl

    - by JohnC
    I am using Maven, CXF 2.2.7, JBoss 4.2.3 and JRE 1.5 I have a Webservice that I can see on the server by using the URL myURL/myService?wsdl I am trying to develop a web app to ping that webservice by calling this in my bean: MyWebService webservice = new MyWebService(); However, it dies and throws the following error, which is very vague: java.lang.ClassCastException: org.apache.cxf.jaxws.ServiceImpl 09:25:59,450 ERROR [STDERR] at javax.xml.ws.Service.<init>(Service.java:81) 09:25:59,450 ERROR [STDERR] at org.otherservice.webservice.MyWebServiceService.<init>(MyWebService.java:44) 09:25:59,450 ERROR [STDERR] at net.myservice.beans.MyBean.getMyServiceSoap(MyBean.java:109) 09:25:59,450 ERROR [STDERR] at net.myservice.beans.MyBean.ack(MyBean.java:240) 09:25:59,450 ERROR [STDERR] at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) 09:25:59,450 ERROR [STDERR] at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39) 09:25:59,450 ERROR [STDERR] at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25) 09:25:59,450 ERROR [STDERR] at java.lang.reflect.Method.invoke(Method.java:585) 09:25:59,450 ERROR [STDERR] at org.apache.el.parser.AstValue.invoke(AstValue.java:131) 09:25:59,450 ERROR [STDERR] at org.apache.el.MethodExpressionImpl.invoke(MethodExpressionImpl.java:276) 09:25:59,450 ERROR [STDERR] at org.apache.jasper.el.JspMethodExpression.invoke(JspMethodExpression.java:68) 09:25:59,450 ERROR [STDERR] at javax.faces.component.MethodBindingMethodExpressionAdapter.invoke(MethodBindingMethodExpressionAdapter.java:77) 09:25:59,450 ERROR [STDERR] at com.sun.faces.application.ActionListenerImpl.processAction(ActionListenerImpl.java:95) 09:25:59,450 ERROR [STDERR] at javax.faces.component.UICommand.broadcast(UICommand.java:383) 09:25:59,450 ERROR [STDERR] at javax.faces.component.UIViewRoot.broadcastEvents(UIViewRoot.java:450) 09:25:59,450 ERROR [STDERR] at javax.faces.component.UIViewRoot.processApplication(UIViewRoot.java:759) 09:25:59,450 ERROR [STDERR] at com.sun.faces.lifecycle.InvokeApplicationPhase.execute(InvokeApplicationPhase.java:97) 09:25:59,450 ERROR [STDERR] at com.sun.faces.lifecycle.LifecycleImpl.phase(LifecycleImpl.java:266) 09:25:59,450 ERROR [STDERR] at com.sun.faces.lifecycle.LifecycleImpl.execute(LifecycleImpl.java:132) 09:25:59,450 ERROR [STDERR] at javax.faces.webapp.FacesServlet.service(FacesServlet.java:244) 09:25:59,450 ERROR [STDERR] at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:290) 09:25:59,450 ERROR [STDERR] at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:206) 09:25:59,450 ERROR [STDERR] at org.apache.myfaces.webapp.filter.ExtensionsFilter.doFilter(ExtensionsFilter.java:301) 09:25:59,450 ERROR [STDERR] at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:235) 09:25:59,450 ERROR [STDERR] at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:206) 09:25:59,450 ERROR [STDERR] at net.faces.filters.AuthorizationFilter.doFilter(AuthorizationFilter.java:84) 09:25:59,450 ERROR [STDERR] at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:235) 09:25:59,450 ERROR [STDERR] at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:206) 09:25:59,450 ERROR [STDERR] at org.jboss.web.tomcat.filters.ReplyHeaderFilter.doFilter(ReplyHeaderFilter.java:96) 09:25:59,450 ERROR [STDERR] at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:235) 09:25:59,450 ERROR [STDERR] at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:206) 09:25:59,450 ERROR [STDERR] at org.apache.catalina.core.StandardWrapperValve.invoke(StandardWrapperValve.java:230) 09:25:59,450 ERROR [STDERR] at org.apache.catalina.core.StandardContextValve.invoke(StandardContextValve.java:175) 09:25:59,450 ERROR [STDERR] at org.jboss.web.tomcat.security.SecurityAssociationValve.invoke(SecurityAssociationValve.java:182) 09:25:59,450 ERROR [STDERR] at org.jboss.web.tomcat.security.JaccContextValve.invoke(JaccContextValve.java:84) 09:25:59,450 ERROR [STDERR] at org.apache.catalina.core.StandardHostValve.invoke(StandardHostValve.java:127) 09:25:59,450 ERROR [STDERR] at org.apache.catalina.valves.ErrorReportValve.invoke(ErrorReportValve.java:102) 09:25:59,450 ERROR [STDERR] at org.jboss.web.tomcat.service.jca.CachedConnectionValve.invoke(CachedConnectionValve.java:157) 09:25:59,450 ERROR [STDERR] at org.apache.catalina.core.StandardEngineValve.invoke(StandardEngineValve.java:109) 09:25:59,450 ERROR [STDERR] at org.apache.catalina.connector.CoyoteAdapter.service(CoyoteAdapter.java:262) 09:25:59,450 ERROR [STDERR] at org.apache.coyote.http11.Http11Processor.process(Http11Processor.java:844) 09:25:59,450 ERROR [STDERR] at org.apache.coyote.http11.Http11Protocol$Http11ConnectionHandler.process(Http11Protocol.java:583) 09:25:59,450 ERROR [STDERR] at org.apache.tomcat.util.net.JIoEndpoint$Worker.run(JIoEndpoint.java:446) 09:25:59,450 ERROR [STDERR] at java.lang.Thread.run(Thread.java:595) I am hoping someone has seen this exception before and can help me.

    Read the article

< Previous Page | 99 100 101 102 103 104 105 106 107 108 109  | Next Page >