Search Results

Search found 19419 results on 777 pages for 'network study'.

Page 103/777 | < Previous Page | 99 100 101 102 103 104 105 106 107 108 109 110  | Next Page >

• What is the best way to connect a 3 switches with a router?

  - by Carlos Morales

  Hello everyone, I'm trying to rebuild the network from my work and I was thinking what is the best way to connect three switches and a router. The router has 4 ports so I thought to connect 2 switches to the router (each switch connected with 2 cables to the router) and then connect the third switch to one of the others with two cables. So is like this, two cables from switch one to the router, two cables from switch two to the router and two cables from switch 3 to switch 1 or 2. So my questions are: Is it better to connect the router to each switch with a cable or the more cables you have the better? If I connect the switch 3 to switch 1 or 2 is it better to connect it with a cable or you get better performance with more cables. If I'm wrong and there is a better or more efficient way to connect them please let me know. The router is a Netgear RP114 (I'll upgrade it to a Sonicwall NSA 240), switch 1 is a Netgear GS748T, switch 2 is a Cisco Catalyst 2924-XL and switch 3 is a D-link DGS-1024D Thank you very much

  Read the article

• No Homegroup Computers, Network Troubleshooter Fails

  - by Mokubai

  I have a problem with my Windows 7 Homegroup, between two Windows 7 Home Premium machines. On one machine I get this: The other machine in the Homegroup is perfectly happy and is able to see and browse this faulty machine as if there is nothing wrong. The Network and Sharing Center shows that I am joined to a Homegroup on my "Home" network and nothing is out of the ordinary. I have tried leaving the Homegroup and rejoining/recreating it several times and that does nothing at all. Normal browsing to machine names and looking through folders seems to work, but it's a much more clunky way to get stuff compared to the convenience of the Homegroup facilities. Starting the troubleshooter detects some problems with a "Peer Networking" (PNRpr or something like that) service not starting but fails to fix anything. Sure enough when I go to view the services via Control Panel - Administrative Tools - Services I see that both the "Peer Name Resolution Protocol" and "Peer Networking Grouping" services are stopped. Attempting to start the "Peer Networking Grouping" gives an error that a dependency service will not start, the only service it is dependant on is the "Peer Name Resolution Protocol" so I try to start that and I get an error saying that the "service could not start due to error 0x80630801" This has happened before and I have fixed it then by using System Restore and restoring the machine to a week before when I knew it had all worked. This time though I cannot remember when I last used the Homegroup from this machine and I've installed quite a bit so I don't want to go fumbling through restore points trying to find one that works... Can anyone tell me if there is a way to reset things so that this machine is able to use the Homegroup again?

  Read the article

• Delete ARP cache on Mac OS when moving from one Wifi network to the other

  - by Puneet

  I am facing wireless connectivity problems when I move from one Wifi network to the other. Here is how it happens: I am at my friends place. I connect to his Wifi. His Wifi router ip address is 192.168.0.1. Everything is fine I close my laptop, come back to my house, open my laptop and I connect to the Wifi Network at my place. Different ESSID, but the Wifi router address is the same 192.168.0.1. At this point I cant get to anything on the internet. To debug I try to see if I can ping the router (192.168.0.1), I cant. I get a no route to host. Meanwhile airport tells me Im connected to Wifi. I see the arp cache and I see a permanent entry for 192.168.0.1 ? (192.168.0.1) at 5c:d9:98:65:73:6c on en1 permanent [ethernet] This permanent bit looks problematic. I go ahead and delete the arp cache entry and all is fine with the world until I go back to my friends place where the same situation plays out. Now my question is, why the hell is this happening? If there is no way around it, can I run a script on Wifi connect/disconnect to clear out the arp cache? Im using Mac OS X $uname -a Darwin 10.8.0 Darwin Kernel Version 10.8.0: Tue Jun 7 16:33:36 PDT 2011; root:xnu-1504.15.3~1/RELEASE_I386 i386

  Read the article

• What is the best way to connect 3 switches with a router?

  - by Carlos Morales

  Hello everyone, I'm trying to rebuild the network from my work and I was thinking what is the best way to connect three switches and a router. The router has 4 ports so I thought to connect 2 switches to the router (each switch connected with 2 cables to the router) and then connect the third switch to one of the others with two cables. So is like this, two cables from switch one to the router, two cables from switch two to the router and two cables from switch 3 to switch 1 or 2. So my questions are: Is it better to connect the router to each switch with a cable or the more cables you have the better? If I connect the switch 3 to switch 1 or 2 is it better to connect it with a cable or you get better performance with more cables. If I'm wrong and there is a better or more efficient way to connect them please let me know. The router is a Netgear RP114 (I'll upgrade it to a Sonicwall NSA 240), switch 1 is a Netgear GS748T, switch 2 is a Cisco Catalyst 2924-XL and switch 3 is a D-link DGS-1024D Thank you very much

  Read the article

• Setting Up My Home Network

  - by Skizz

  I currently have five PCs at home, three running WinXP and two running Ubuntu. They are set up like this: ISP ----- Modem ---- Switch ---- Ubuntu1 -- B&W Printer | |--WinXP1 | |--WinXP2 Wireless |--Colour Printer | |---------Ubuntu2 |---------WinXP3 (laptop) The Ubuntu1 machine is set up as a PDC using Samba and runs fetchmail, procmail, dovecot to get my e-mail and allow me to access the e-mail via imap so I can read the e-mail on any PC. I'd like to set up the network like this: ISP ----- Modem ---- Ubuntu1 ---- Switch ------WinXP1 | | |--WinXP2 B&W Printer Wireless |--Colour Printer | |---------Ubuntu2 |---------WinXP3 (laptop) My questions are: How to configure Ubuntu1 to act as a firewall. How to configure Ubuntu1 to provide a consistant user authentication across the network, at the moment Samba provides roaming profiles for the XP machines but the Ubuntu2 machine has it's own user lists. I'd like to have a single authentication for both XP machines and linux machines so that users added to the server list will propagate to all PCs (i.e. new users can log on using any PC without modifying any of the client PCs). How to configure a linux client (Ubuntu2 above) to access files on the server (Ubuntu1), some of which are in user specific folders, effectively sharing /home/{user} per user (read and write access) and stuff like /home/media/photos with read access for everyone and limited write access. How to configure the XP machines (if it is different from a the Samba method). How to set up e-mail filtering. I'd like to have a whitelist/blacklist system for incoming e-mails for some of the e-mail accounts (mainly, my kids' accounts) with filtered e-mails being put into quaranteen until a sysadmin either adds the sender to a blacklist or whitelist. OK, that's a lot of stuff. For now, I don't want config files*, rather, what services / applications to use and how they interact. For example, LDAP could be used for authentication but what else would be useful to make the administration of the LDAP easier. Once I have a general idea for the overall configuration, I can ask other questions about the specifics. Skizz I have looked around for information, but most answers are usually in the form of abstract config files and lists of packages to install.

  Read the article

• SBD killing both cluster nodes when there are even small SAN network problems

  - by Wieslaw Herr

  I am having problems with stonith SBD in a openais-based cluster. Some background: The active/passive cluster has two nodes, node1 and node2. They are configured to provide an NFS service to users. To avoid problems with split-brain, they are both configured to use SBD. SBD is using two 1MB disks available to the hosts via an multipath fibre-channel network. The problems start if something happens with the SAN network. For example, today one of the brocade switches got rebooted and both nodes lost 2 out of 4 paths to each disks, which resulted in both nodes committing suicide and rebooting. This, of course, was highly undesirable because a) there were paths left b) even if the switch would be out for 10-20 seconds a reboot cycle of both nodes would take 5-10 minutes and all NFS-locks would be lost. I tried increasing the SBD timeout values (to 10sec+ values, dump attached at the end), however a "WARN: Latency: No liveness for 4 s exceeds threshold of 3 s" hints that something isn't working as I would it expect to. Here is what I would like to know: a) Is SBD working as it should killing nodes when 2 paths are available? b) If not, is the multipath.conf file attached correct? The storage controller we use is an IBM SVC (IBM 2145), should there be any specific configuration for it? (as in multipath.conf.defaults) c) How should I go about increasing the timeouts in SBD attachements: Multipath.conf and sbd dump (http://hpaste.org/69537)

  Read the article

• linux keeps disconnecting from wireless network

  - by Matteo Ceccarello

  I'm running Arch Linux on an Acer laptop and my wirless connection doesn't stay up. After a while it disconnects, and when I try to reconnect I get stuck with a "Waiting for authorization" message. I have to retry several times before getting the connection stay up for few minutes. This happens with both networkmanager and wicd. The strange thing is that the iMac that sits next to the laptop connects fine, and when I use my laptop within the university wireless network it works normally. How can I solve this problem? EDIT: I've tried to connect manually following the steps iwlist wlan0 scan wpa_supplicant -i wlan0 -c /etc/wpa_supplicant.conf dhcpcd wlan0 and it works, I can ping google. However, looking to wpa supplicant output I see that it keeps connecting and disconnecting. I'm using WPA2, and this seems to be a problem in authentication. EDIT 2: as pointed out in the answers I forgot to mention my hardware/software specifications: kernel: Linux 3.0-ARCH wireless card: # lspci | grep -i net 07:00.0 Network controller: Intel Corporation WiFi Link 5100 module used # lsmod | grep -i 80211 mac80211 216021 1 iwlagn I use a Netgear DGN1000 modem/router My dmseg output is shown here http://pastebin.com/8Tf7iage

  Read the article

• What was SPX from the IPX/SPX stack ever used for?

  - by Kumba

  Been trying to learn about older networking protocols a bit, and figured that I would start with IPX/SPX. So I built two MS-DOS virtual machines in VirtualBox, and got IPX communications working (after much trial and error). The idea being to get several old DOS games to run, link up to a multiplayer match, interact with each game window, and capture the traffic using Wireshark from the host machine. From this, I got Quake, Masters of Orion 2, and MechWarrior 2 to communicate back and forth. Doom, Doom2, Duke3d, Warcraft, and several others either buggered up under the VM or just couldn't see the other VM on the IPX network. What did I discover? None of the working games used SPX. Not even Microsoft's NET DIAG used SPX. They all ran ONLY on top of IPX. I can't even find SPX examples or use-cases of SPX traffic running over IEEE 802.3 Ethernet II framing. I did find references that it was in abundant use on token ring, but that's it. Yet any IPX-aware application that I've hunted down so far usually advertises itself as "IPX/SPX", which seems to be a bit of a misnomer, since it doesn't seem to use SPX. So what was SPX used for? Any DOS applications out there that use it which will run under my VM setup? Edit: I am aware that IPX is to SPX as IP is to TCP (layer 3 to layer 4), so I expected to see an SPX layer underneath the IPX layer in Wireshark when I ran my tests.

  Read the article

• What is the peak theoretical WiFi G user density? [closed]

  - by Bigbio2002

  I've seen a few WiFi capacity planning questions, and this one is related, but hopefully different enough not to be closed. Also, this is related specifically to 802.11g, but a similar question could be made for N. In order to squeeze more WiFi users into a space, the transmit power on the APs need to be reduced and the APs squeezed closer together. My question is, how far can you practically take this before the network becomes unusable? There will come a point where the transmit power is so weak that nobody will actually be able to pick up a connection, or be constantly roaming to/from APs spaced a few feet apart as they walk around. There are also only 3 available channels to use as well, which is a factor to consider. After determining the peak AP density, then multiply by users-per-AP, which should be easier to find out. After factoring all of this in and running some back-of-the-envelope calculations, I'd like to be able to get a figure of "XX users per 10ft^2" or something. This can be considered the physical limit of WiFi, and will keep people from asking about getting 3,000 people in a ballroom conference on WiFi. Can anyone with WiFi experience chime in, or better yet, provide some calculations for a more accurate figure? Assumptions: Let's assume an ideal environment with no reflection (think of a big, square, open room, with the APs spaced out on a plane), APs are placed on the ceiling so humans won't absorb the waves, and the only interference are from the APs themselves and the devices. As for what devices specifically, that's irrelevant for the first point of the question (AP density, so only channel and transmit power should matter). User experience: Wikipedia states that Wireless G has about 22Mbps maximum effective throughput, or about 2.75MB/s. For the purpose of this question, anything below 100KB/s per user can be deemed to be a poor user experience. As for roaming, I'll assume the user is standing in the same place, so hopefully that will be a non-issue.

  Read the article

• Show full URI/URL in Chrome's developer tools Network tab

  - by Lev

  When using Chrome to debug, I find it incredibly difficult to be efficient due to the fact that I don't see how I can force the "Network" tab of the developer tools to show the full request URI. It will show the full URI if you hover the link and wait a second, but this is incredibly counterproductive. All of my AJAX requests are sent to ajax.php, and handled by using query string arguments, like: ajax.php?do=profile-set ajax.php?do=game-save ... etc. Since I use AJAX extensively, my network tab is filled with "ajax.php", but I have to manually hover each and every entry to find the request I am looking for. Surely there has got to be another way!? I am constantly fed up by something new in Firefox and immediately force myself back into Chrome, but it is always the developer tools in Chrome that keep me from using it for an extended period of time. Hopefully I can find out how to do this so I can continue using Chrome as my numero uno. I've provided a screen shot to show you where I mean:

  Read the article

• scalable yet doable small-medium office network

  - by Jared

  Hello, I'm studying up with both Microsoft and Cisco literature and I must say, my head is starting to get clustered up (pun intended). I've made a quick network diagram of a theoretical company... Company1 owns Company 2 and Company 3, which are all under separate rooms and networks, but must be able to share a few resources such as files or printers. Given the amount of info out there and best practices, I thought about posting here to get suggestions and see what would the pro's do. I can read and read all day and implement on my own, but if I dont get some outside input, how will I know if I'm doing something wrong, right? anyway, please take a look and see if this is an over-complicated network or a lackluster design for a small-medium company of about 35 people and lets say they will be double that number by end of the year... :) Using win2k3, esxi, windows xp. FCS - forefront client security, ACS - access control system, SPCWK - spiceworks, XCH - Exchange Im not allowed to post an image yet, so here's the link ---- GLIFFY IMAGE Flame suit is on just in case people get mad at me for making an "abomination". I'd really want to get the general overview properly before I dive into the more complicated things

  Read the article

• Can a folder on a NAS be made available as a physical drive in VMWare?

  - by asbjornu

  We are currently in the process of moving from a single web server to two load balanced web servers and are facing some challenges we don't quite know how to fix. One of these is that the current single server hosts applications that write stuff to disk. The applications running on the server expects that when something is written to disk it later will in fact exist, so it's important that this premise is fulfilled with the dual server architecture as well. The dual server setup is a couple of VMWare instances with Windows Server 2008 R2 as the guest operating system. Out of the box, these instances does not share any kind of file system, so just moving the applications over would make them break since one instance would write something to the file system that doesn't exist on the other. Thus we need to share a file system between the two virtual servers. Our host has proposed to create a network share on a SAN and map this share individually on each virtual machine. This doesn't work too well due to NTFS permissions, etc., because the share needs to be accessed by several independent web applications that won't even be in the same application pool. The only solution that kind of works is to hard code an "identity" for each web application into its web.config file, but this means password in clear text which doesn't sit well with me. Since the servers are virtual, I'm thinknig: Wouldn't it be possible to make a NAS area available as a physical disk in the gues operating system somehow? Since VMWare has full control of the virtual hardware, you'd think it would be able to "fake" a local hard drive in the virtual machine that in reality is a folder on a NAS, but so far I haven't found anything that states how and if this is possible. So I have to ask the wonderful Server Fault community: Can a folder on a NAS be made available as a physical drive (typical D:) in both of the virtual machines?

  Read the article

• Destination NAT Onto the Same Network from internal clients

  - by mivi

  I have a DSL router which acts as NAT (SNAT & DNAT). I have setup a server on internal network (10.0.0.2 at port 43201). DSL router was configured to "port forward" (or DNAT) all incoming connections to 10.0.0.2:43201. I created a virtual server for port forwarding on DSL router. I also added following iptables rules for port forwarding. iptables -t nat -A PREROUTING -p tcp -i ppp_0_1_32_1 --dport 43201 -j DNAT --to-destination 10.0.0.2:43201 iptables -I FORWARD 1 -p tcp -m state --state NEW,ESTABLISHED,RELATED -d 10.0.0.2 --dport 43201 -j ACCEPT # ppp_0_1_32_1 is routers external interface. # routers internal IP address is 10.0.0.1 and server is setup at 10.0.0.2:43201 Problem is that connections coming from external IP addresses are able to access internal server using External IP address, but internal clients (under NAT) are not able to access server using external IP address. Example: http://<external_address>:43201 is working from external clients But, internal clients are not able to access using http://<external_address>:43201 This seems to be similar to the problem described in http://www.netfilter.org/documentation/HOWTO/NAT-HOWTO-10.html (NAT HOW-TO Destination NAT Onto the Same Network). Firstly, I am not able to understand why is this a problem for internal clients? Secondly, what iptables rule will enable internal clients to access server using external IP address? Please suggest.

  Read the article

• Windows 7, Printer is unavailable until PC reboot

  - by Cjs

  We are having a problem that I haven't seen before and can find no answers to online. A desktop running Windows 7 is unable to print using network printers. When the user tries, no matter what printer it is, he get's the following message when using Microsoft Office applications: "Current printer is unavailable. Select another printer." When the end user uses Outlook we get the message: "Printing is not available. There are no printers installed. You can select and configure a printer in Windows Control Panel." Now here is the confusing part, if we reboot the pc it works fine for a little while and then goes back to the same old same old. The printers are working fine for every other user as well so I believe it is the user's machine. If anyone has any ideas please let me know. Edit: I'd like to add in that some people were having luck disabling snmp for the printers. Restarting the print spooler doesn't seem to do anything.

  Read the article

• How to test/debug bad network wiring?

  - by Jack Lloyd

  I recently bought a place already wired with Cat 5E (8 ports, leading to a central closet). However attempting to get link, nothing works. On closer examination, it was obvious that the ends in the closet were wired backwards (brown on pin 1, etc). The jacks that I've pulled out of the wall do look to be correctly done. However, testing with a network cable tester shows zero link between any of the jacks and any of the ports in the closet - I had expected to just see a 1/8, 2/7, ... 8/1 mismatch, but instead get nothing at all. The runs are accessible and look neat, though they take some bends that seem quite sharp and are in some cases much longer than they need to be (the person who put this in was a professional electrician but I suspect this was the first time he ran network cabling). My best guess at this point is that he either bought bad cable, or put so much tension on it that he snapped wires. Though it seems surprising/unlikely that I wouldn't get at least one active wire on one of the 8 lines. So, my question: is there anything else I should try or test before I go ripping out everything and running new cable?

  Read the article

• Connection to Google, Yahoo, Bing, Ask, etc. compromised via all devices on my home network - How?

  - by jt0dd

  I'm a very computer savvy guy (although not very networking savvy), and I may still be wrong about this, but I think my home network may be compromised somehow. I'd like to know if it's possible for someone to have hijacked my network's connection to Google.com and other popular websites. Update: The issue seems to take effect with all popular websites. I can connect to small (non-popular) websites without issue, but Facebook, Google, Yahoo, and Bing cannot be accessed by any device on my home network. On all devices using my home network, I'm being shown http://www.google.com WARNING! Internet Explorer is currently out of date. Please update to continue. when I attempt to connect to google.com. I wouldn't be surprised by this at all if it were just the laptop. It's the fact that this is happening on all devices on my network that confuses me. Here's the screenshot from my iPhone, for reference. Can my home network be compromised? Is that even possible? How can something like this happen across all platforms on all devices in the same way? I wouldn't imagine every device / platform on the network would get the same virus. Should I assume that my network's security is totally compromised? Update: All mobile devices and laptops on my home network are experiencing the same alert when attempting to connect to google.com.

  Read the article

• Reliable backup software for windows network/samba shares.

  - by Eli

  Hi All, I have a Win2003 server that works as a pdc for a number of XP boxes, and a couple related FreeBSD boxes. I need to back up roaming profiles, non-roaming profiles via network shares, local hard drive data, and files on the FreeBSD boxes via samba shares. I have tried Genie Backup Manager and Backup4All pro, and both have excellent features, but both also begin to fail disastrously with more than a few days use. Mostly, the errors seem to have been from the backup catalog getting out of synch with itself. Whatever it is, there is no excuse for a backup software that says it backed up files when it really didn't, or the log saying it backed up exactly the same file 10,000 times in a single run, or flat-out crashing, or any of the other myriad problems I've run into with these. Really sad for products that fill such an important need. Anyway, does anyone know of a backup software that works reliably and can do the following? Scheduled backups for multiple jobs, without a user logged in. Backup from local hard drives or network shares. Incremental backups. Thanks! Edit: Selected solution: I've added my (hopefully final) solution as an answer.

  Read the article

• XenServer VMs can't reach network

  - by toto

  I'm currently trying to setup a small cloud architecture , I'm using in the installation CloudStack 2.2.14 which need two node : a management server (as node1) to provision the cloud and a hyperviser XenServer 5.6 SP2 to host the VMs (as node2). I succeded to create both node1 and node2 into an ESXi 5 VMWare as VMs. So The ESXi 5 is hosting two VMs node1 + node2 , and node2 which is the XenServer will host also VMs (such as ubuntu or Centos). Both node1 and node2 can ping each other and can get the internet connection from Esxi5 ,but My problem is : that VMs into the node2(XenServer) can't reach the network (can't ping node1 or Esxi or get an internet connection but they can ping VMs IN the node2(XenServer). So I tried to: 1-Setup a DHCP server as node3 in ESXi5 and connect node2(Xenserver) to him , but always the VMs into to node2 can't reach the outer network. 2-Setup a DCHP server into node2 , but always the same problem. So , 1-is there any other configuration i'm missing in node2 (considering that I'm sure about DNS , GW , NETMASK configuration)?. 2-Is it the problem because i'm Creating VMs into node2(XenSever) which is a VM into ESXi 5 ?

  Read the article

• XP/Intel wirelss only showing 'hpsetup' ad-hoc network that isn't there

  - by ewall

  Trying to help my friend with her work XP laptop, which recently stopped seeing any wireless SSIDs except the SSID 'hpsetup' (presumably from a wireless-enabled HP printer). Relevant information: The laptop is a Lenovo T500 (Centrino 2 chipset) with XP SP3. The network adapter is Intel WiFi Link 5300 AGN (built-in). The latest version (13.5) of the Intel drivers only are installed, not the Intel config software, so XP is using the Wireless Zero-Config manager. The wireless router is a NetGear WGR614 v7 with 802.11b/g. The SSID is broadcasting, and all the other laptops in the house can see and connect to it. On the laptop, I have tried repairing the network connection, disabling power management, turning off 802.11a & n radio, and more... but it didn't help. Some of the wireless settings are managed by Group Policy from her office (I get the "At least one of your changes was not applied successfully to your wireless configuration" message). It is enforced to connect to "Access point (infrastructure) networks only". The real kicker is that my laptop does not an SSID named 'hpsetup' here, but it can see several broadcasted SSIDs including the one we want, while my friend's laptop doesn't see any SSID except 'hpsetup'. Any suggestions?

  Read the article

• Route specific network traffic through vpn in virtualbox guest

  - by Sander

  I am running OSX with a windows server 2008 guest in Virtualbox. My goal is to route some of the network traffic in the host through the server guest. This is because the win2008 server has a VPN connection to my workplace using a Smartcard solution which can not operate on OSX. My current set-up is like this: OSX (Host): connected to the internet via en01 Win2008 (Guest): connected to the internet using NAT (lan1 in guest) has a SSTP VPN connection to my workplace is connected to the guest using an Host Only Adapter vboxnet0 (LAN2 in guest) The important part is about the host (OSX). Primarily I want all network traffic to just go through en01. However, all traffic which can only be accessed through the VPN must go through the guest and through the VPN. I have one specific FQDN which can only be accessed through the VPN (say corp.mycompany.com). I do not know much about networking. I thought I would be able to get it to work by bridging together LAN2 and LAN1 but this didn't seem to work this: http://archives.aidanfindlater.com/blog/2010/02/03/use-vpn-for-specific-sites-on-mac-os-x/ using a loopback adapter on WinXP (when I did not have win2008 yet, but this doesn't work because I can't create a PPTP connection) And I've also read about Routing and Remote Access but I have no idea on how to use this. Can someone help me in the right direction?

  Read the article

• Sharing music on NAS with other zunes and ipods

  - by osij2is

  After being a long time iPod owner, I'm switching to the new Zune with its subscription model. I haven't bought a Zune yet but I'm planning on doing so within the next month or so. I have approximately 40gb worth of music and my girlfriend has her iPod music library around 30gb. I've been trying to figure out how to migrate all our music off of our laptops/desktops and centralize everything on my NAS. In sharing iPod music isn't too bad. Sharing from one machine to all is fairly easy within the iTunes player. As far as storing all the music on a NAS, again, iPods aren't too bad and imagine other systems aren't difficult. But I'm really new to the Zune and I'm beginning to run into some issues. My questions are: Is it possible to store all music from our iPods and Zune subscriptions and share music between the iPod/Zune within the same file share on my NAS? I'm sure it's possible to store music on a share, but I'm not sure how iTunes and the Zune software differs. Is there 3rd party software, maybe something like DoubleTwist that can sync based from NAS to multiple desktop/laptops? I've never used DoubleTwist but it's something that I found that looks close to being what I need. I've never quite done this myself so I'm trying to find a solution that can: a) store music on a network share; b) sync between different devices (zune/ipod) seamlessly.

  Read the article

• What should be monitored to troubleshoot file sharing problems?

  - by RyanW

  I'm running into some problems with a file share used by an ASP.NET web application. With this configuration, there are 2 web servers (win2k8 web) that connect to a file server (win2k8 enterprise), reading and writing files using a file share. Recently, one of the web servers has begun encountering an error accessing the file share: IOException: The specified network name is no longer available. There does not appear to be much info on the web for explaining what's causing this and how to best fix it, so I'm looking at what I can monitor in order to get clues. I'm not sure if it's hardware, just a load issue, file size, frequency, etc. With Windows perfmon, what can I monitor on the File Server side? There's the "Files Open" object, any other good ones? What can I monitor on the web server side? EDIT: I'll add that the UNC path uses the IP address of the file server, not a name to resolve. Also the share is a single, flat directory with over 100K files.

  Read the article

• Configure a Windows PC as network appliance w/o monitor, keyboard and mouse

  - by Joshua Lim

  I intend to use a small form factor PC with Windows 7 Professional installed as a network appliance attached directly to my customer's LAN without connecting a monitor, keyboard or mouse. How should I configure the networking for my PC so that I can access it via say my laptop? I figure that I can do it 2 ways. Attach my laptop to the PC using a crossover cable? Connect via RDP and configure networking. Configure an IP address on the PC before I deliver it to the customer place. At the customer's place, attach the PC to LAN and connect to the IP address which I previously configured from my laptop or from one of the customer's workstations. I know the first way is doable, but is the second way possible? I'm sorry if this question sounds ridiculous - I am Delphi programmer but a novice on networking. Finally, if possible, I hope to make the configuration process web based as I wouldn't like to reveal the fact that I am using Win7 Pro for the network appliance!

  Read the article

• High speed network configuration

  - by Peter M

  Sorry if this seems to be a stupid question, I'm not sure how to specify what I want to know when checking google. I will have 2 or 3 devices pumping out data on a 100Base-T port. The combined data rate of all devices is about 15KB/S which exceeds the optimal 100Base-T channel capacity (12KB/S), but well within the realms of a 1000Base-T connection. Each device will be sending a burst of data in the form of an FTP transfer to a common, single host computer in a sequential manner ie: Device A establishes FTP connection and transfers data Device B establishes FTP connection and transfers data Device C establishes FTP connection and transfers data It may be that the A&B, B&C and C&A transfers overlap in the time domain to some extent. There will be minimal traffic going back from the computer to each device (in general what ever is needed to support the FTP transfers), and the network will be dedicated to transferring data between these devices and the host computer. Is it possible to use a switch to combine the multiple incoming 100Base-T streams into a single outgoing 1000Base-T stream? if so what features in a switch should I be looking for? Or would it be better to have 3 physical point-to-point 100Base-T dedicated connections between each device and the host computer? (thus having at least 3 physical Ethernet interfaces on that computer) Note that I can't change the interface on the devices, but I am free to choose the network and host computer configuration. Thanks for you help Peter

  Read the article

• Moving Microsoft Exchange server to the private network.

  - by Alexey Shatygin

  In one of the offices, we have a 50-computers network, which had only one server machine: Windows 2003 Server Microsoft ISA Server Microsoft Exchange 2003 This server worked as a gateway (proxy server), mail server, file server, firewall and domain controller. It had two network interfaces, one for WAN (let's say 222.222.222.222) and one for LAN (192.168.1.1). I set up a Linux box to be the gateway (without a proxy), so the Linux box now has the following interfaces: 222.222.222.222 (our external IP, we removed it from the Windows machine) and 192.168.1.100 (internal IP), but we need to keep the old Windows server as a mail server and a proxy for some of our users, until we prepare another Linux machine for that, so I need the mail server on that machine to be available from the Internet. I set up iptables rules to redirect all the incoming connections on the 25th and 110th ports of our external IP to 192.168.1.1:25 and 192.168.1.1:110 and when I try to telnet our SMTP service telnet 222.222.222.222 25 I get the greetings from our windows server's (192.168.1.1) SMTP service, and that's works fine. But when I telnet POP3 service telnet 222.222.222.222 110 I only get the blank black screen and the connection seem to disappear if I press any button. I've checked the ISA rules - everything seems to be the same for 110th and 25th ports. When I telnet on 110th ports of our Windows server from our new gateway machine like this: telnet 192.168.1.1 110 I get the acces to it's POP3 service: +OK Microsoft Exchange Server 2003 POP3 server version 6.5.7638.1 (...) ready. What sould I do, to make the POP3 service available through our new gateway?

  Read the article

< Previous Page | 99 100 101 102 103 104 105 106 107 108 109 110  | Next Page >