Search Results

Search found 10306 results on 413 pages for 'opensuse 11 3'.

Page 104/413 | < Previous Page | 100 101 102 103 104 105 106 107 108 109 110 111  | Next Page >

  • How to route traffic from a subnet 10.0.0.x to a network 200.208.88.17

    - by Guilherme Longo
    I have the following configuration Router : IP: 200.208.88.17 (Internet) MASK: 255.255.255.40 Server 2003 : IP: 10.0.0.1 (with dhcp server ativated) dhcp scope: 10.0.0.11 - 10.0.0.254 MASK: 255.255.255.0 clients : IP: 10.0.0.11 - 10.0.0.254 MASK: 255.255.255.0 At this point I have all computer set-up in one switch. All clients are receiving ip´s from the dhcp server. I need to enable the internet in every client. I am not sure how to route the traffic from the clients to the router that is providing internet access. Could you please point me to the right direction?

    Read the article

  • SNMP counter issues with cisco RV082

    - by Chance
    Does anyone else poll this router with SNMP? We are using firmware version: 2.0.0.19-tz We are having problems with the traffic counters, some of them appear to be implemented as 16 bit counter instead of 32 bit counters. The reason this is causing problems is that they roll over (at 65,000) to 0 in less than our minute polling cycle, really skewing our metrics. The counter for the Lan (interface 2) seems to be functioning properly, however interfaces 3 and 4 (WAN and DMZ / WAN2) rollover at 65000. Tue May 11 08:38:31 EDT 2010 IF-MIB::ifInOctets.1 = Counter32: 137634 IF-MIB::ifInOctets.2 = Counter32: 1865677943 IF-MIB::ifInOctets.3 = Counter32: 12450 IF-MIB::ifInOctets.4 = Counter32: 49354 Look at counter IF-MIB::ifInOctets.4 5 seconds later: Tue May 11 08:38:36 EDT 2010 IF-MIB::ifInOctets.1 = Counter32: 137634 IF-MIB::ifInOctets.2 = Counter32: 1865836207 IF-MIB::ifInOctets.3 = Counter32: 13167 IF-MIB::ifInOctets.4 = Counter32: 12900 Any suggestions? Seems like a bug to me, however I just wanted to make sure I wasn't crazy.. Thanks!

    Read the article

  • Create manual IPSec policy on Window (like spdadd and add on Linux)

    - by hapalibashi
    Hello On Linux it is possible to create an a manual IPSec (no IKE etc) tunnel thus: spdadd 192.168.0.10/32[5066] 192.168.0.11/32[5064] udp -P in ipsec esp/transport//require; add 192.168.0.10 192.168.0.11 esp 2222 -m transport -E des-ede3-cbc "123456789012123456789012" -A hmac-md5 "1234567890123456"; I need to do the same on Windows. I am aware of netsh but I don't think its equivalent, I need to specific the SPI (thats the 2222 above) and this seems impossible. Any ideas or alternatives?! Thanks, Stuart.

    Read the article

  • How to make PuTTY X11 forwarding work in a screen session?

    - by Alex Howell
    I'm using PuTTY with X11 forwarding enabled, using Xming as my X server on Windows 7. When I SSH to a Linux host, X11 forwarding works fine. If I start a "screen" screen manager session, it still works fine. If I disconnect from the screen session, then later resume in a different PuTTY window using "screen -rd", X11 forwarding doesn't work any more - I get an error: xterm X connection to localhost:11.0 broken (explicit kill or server shutdown). This seems to be because $DISPLAY is different in each PuTTY SSH session (localhost:11.0 in the first session, then localhost:12.0 in the next, and so on). If I manually set $DISPLAY to localhost:12.0 in the screen session, X11 forwarding works again. Is there a way to automatically set $DISPLAY in the screen session, each time it's resumed, so that it always matches the parent PuTTY session's?

    Read the article

  • How to install Oracle's exp / imp binaries

    - by Sotapanna
    I was browsing the net to find a solution, but I had no luck. :( How can I install Oracle's imp / exp binaries to my CentOS box without installing an Oracle Server? I'm accessing an existing Oracle database on another machine, so I only need a client here. I already installed sqlplus and its dependencies (oracle-instantclient11.2-basic-11.2.0.3.0-1.x86_64.rpm, and oracle-instantclient11.2-odbc-11.2.0.3.0-1.x86_64.rpm), but that didn't provide those tools. Do I really need to fully install Oracle? My aim is to suck a database dump from the Oracle to my CentOS box. If there is another way to do this without using exp I wouldn't feel bad about NOT using it, but it seems to me there is no alternative.

    Read the article

  • chroot'ing SSH home directories, shell problem.

    - by Hamza
    Hi folks, I am trying to chroot my SSH users to their home directories and it seems to work.. in a strange way. Here is what I have in my sshd_config: Match group restricthome ChrootDirectory %h The permissions on the user directories looks like this: drwxr-xr-x 2 root root 1024 May 11 13:45 [user]/ And I can see that the user logs in successfully: May 11 13:49:23 box sshd[5695]: Accepted password for [user] from x.x.x.x port 2358 ssh2 (with no error messages after this) But after entering the password the PuTTY window closes down. This is a wild guess, but could it be because the user's shell is set to /bin/bash and it can't execute because of the chroot? If so, could you give me pointers on how to fix it? Would simply copying the bash binary into user's home directory and modyfying the shell work? How would I deal with the dependencies, ldd shows quite a few of those :) Comments/suggestions will be appreciated. Thanks.

    Read the article

  • OSX Server 3, Mac clients binding to OD and Profile Manager failing

    - by dbf
    I've made a setup containing a Mac Mini with OSX Server 3 (Mavericks 10.9.2) using Open Directory and Profile Manager (Mail, etc all set up and working). Now the thing is, internally on the local network, everything works great. Clients can bind to the OD and the users are able to login. I can install trust and settings profiles (either custom or group profiles) and all services in the profiles mentioned are being configured correctly. I can log in and out, hump around and do it a 100 times on different macs with different users, it works. My goal is to make this service publicly. The domain is with a FQDN which I own, for simplicity let's say server.domain.com. Now the only way for me to bind the clients to the OD is using LDAP mapping RCF2307 (without SSL) and a DN suffix of dc=server,dc=domain,dc=com using the Directory Utility. The options from server, or open directory will throw several errors like Connection failed to node '/LDAPv3/server.domain.com (2100). First of all I don't really understand the problem why clients can't bind to the OD like it does locally, with and without SSL (all ports are open, literally all ports are open, not just 389,636 and 1640, wasn't sure if I was missing any). When the clients are using LDAP mapping RFC2307 to bind (without SSL only), clients are able to authenticate, login and even load the Trust profile. But every Settings profile will fail with a Debug Message: Unable to find GUID in user record OD or fail to install saying missing user identification. Is there any way to get this to work without RFC2307? Because there is quite some stuff missing when using RFC2307 and not pull the mapping from the server or use open directory. Is this setup even possible? Or should I use VPN to authenticate with the OD? The network setup is a Modem/Router (DHCP off) with WAN NATted to an Airport Extreme (Using DHCP+NAT). The AE does notify with a double NAT message but I haven't had any problems with it on any other service. So WAN - 192.168.2.220 (static), AE - 10.0.1.* (dhcp) Output of DIG from the outside using dig server.domain.com ;; flags: qr rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;server.domain.com. IN A ;; ANSWER SECTION: server.domain.com. 77 IN A 91.50.*.* (valid WAN IP) ;; SERVER 172.*.*.1#53(172.*.*.1) (iPhone) DIG locally from a client and server (same output) ;; flags: qr aa rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 2, ADDITIONAL: 0 ;; QUESTION SECTION: ;server.domain.com. IN A ;; ANSWER SECTION: server.domain.com. 10800 IN A 10.0.1.11 ;; AUTHORITY SECTION: server.domain.com. 10800 IN NS domain.com. (used for email send in relay) server.domain.com. 10800 IN NS server.domain.com. ;; SERVER 10.0.1.11#53(10.0.1.11) Are there any things I should check? Only have OSX. -- double NAT issue, plugged in the server directly on the Modem/Router with a static IP and issue remains. Guess that rules out the double NAT thing. -- changeip -checkhostname comes with There is nothing to change, e.g. success. Primary address = 10.0.1.11 Current HostName = server.domain.com DNS HostName = server.domain.com For now, I've made a workaround by using an admin account that forces a permanent VPN connection on boot. That means before it comes to the login, a connection is already made or underway. I will continue this post when I have more time, also locating all the necessary .log files of each application involved. I have some suspicions but have to debug a bit more when I have more time on my hands .. Unless, of course, I get sidetracked with having a life. Which is arguably not very likely. krypted.com

    Read the article

  • Logrotate Successful, original file goes back to original size

    - by drewrockshard
    Has anyone had any issues with logrotate before that causes a log file to get rotated and then go back to the same size it originally was? Here's my findings: Logrotate Script: /var/log/mylogfile.log { rotate 7 daily compress olddir /log_archives missingok notifempty copytruncate } Verbose Output of Logrotate: copying /var/log/mylogfile.log to /log_archives/mylogfile.log.1 truncating /var/log/mylogfile.log compressing log with: /bin/gzip removing old log /log_archives/mylogfile.log.8.gz Log file after truncate happens [root@server ~]# ls -lh /var/log/mylogfile.log -rw-rw-r-- 1 part1 part1 0 Jan 11 17:32 /var/log/mylogfile.log Literally Seconds Later: [root@server ~]# ls -lh /var/log/mylogfile.log -rw-rw-r-- 1 part1 part1 3.5G Jan 11 17:32 /var/log/mylogfile.log RHEL Version: [root@server ~]# cat /etc/redhat-release Red Hat Enterprise Linux ES release 4 (Nahant Update 4) Logrotate Version: [root@DAA21529WWW370 ~]# rpm -qa | grep logrotate logrotate-3.7.1-10.RHEL4 Few Notes: Service can't be restarted on the fly, so that's why I'm using copytruncate Logs are rotating every night, according to the olddir directory having log files in it from each night.

    Read the article

  • Replies to request coming over a relay goes to relay's internal IP, not to original request's source IP

    - by seaquest
    Dhcpd running on Linux gets a dhcp request over dhcrelay which is running on other remote machine. Oct 6 10:09:46 2012 dhcpd: DHCPDISCOVER from 00:1e:68:06:eb:37 (oguz-U300) via 172.16.17.81 tcpdump: listening on eth1, link-type EN10MB (Ethernet), capture size 96 bytes 10:35:01.112500 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto: UDP (17), length: 328) 192.168.0.81.67 > 192.168.0.1.67: BOOTP/DHCP, Request from 00:1e:68:06:eb:37, length: 300, hops:1, xid:0xe378fc7e, flags: [none] (0x0000) Gateway IP: 172.16.17.81 Client Ethernet Address: 00:1e:68:06:eb:37 [|bootp] It matches to a subnet and send reply. However reply does not go to the requesting dhcrelay external IP(192.168.0.81). Instead, it goes to the internal interface IP of machine running dhcrelay. And I think because of this remote machine running dhcrelay or the dhcrealy itself discarding packet. Oct 6 10:09:46 2012 dhcpd: DHCPOFFER on 172.16.17.11 to 00:1e:68:06:eb:37 (oguz-U300) via 172.16.17.81 10:35:02.050108 IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto: UDP (17), length: 328) 192.168.0.1.67 > 172.16.17.81.67: BOOTP/DHCP, Reply, length: 300, hops:1, xid:0xe378fc7e, flags: [none] (0x0000) Your IP: 172.16.17.11 Gateway IP: 172.16.17.81 Client Ethernet Address: 00:1e:68:06:eb:37 [|bootp] Is this a normal behaviour? Machine running dhcrelay: eth1(ext) Link encap:Ethernet HWaddr 00:90:0B:21:43:F4 inet addr:192.168.0.81 Bcast:192.168.0.255 Mask:255.255.255.0 eth2(int) Link encap:Ethernet HWaddr 00:90:0B:21:43:F5 inet addr:172.16.17.81 Bcast:172.16.17.255 Mask:255.255.255.0 3582 ? Ss 0:00 /usr/sbin/dhcrelay -i eth2 192.168.0.1 Machine running dhcpd: eth1 Link encap:Ethernet HWaddr 00:90:0B:23:97:D1 inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0 option domain-name "test.com"; option subnet-mask 255.255.255.0; authoritative; ignore client-updates; ddns-update-style ad-hoc; default-lease-time 86400; max-lease-time 86400; subnet 192.168.0.0 netmask 255.255.255.0 { range 192.168.0.135 192.168.0.169; option broadcast-address 192.168.0.255; option domain-name-servers 192.168.0.1; option domain-name "test.com"; option routers 192.168.0.1; } subnet 172.16.17.0 netmask 255.255.255.0 { local-address 192.168.0.1; server-identifier 192.168.0.1; range 172.16.17.10 172.16.17.11; option broadcast-address 172.16.17.255; option routers 172.16.17.81; } (I put local-address and server-identifier. But this does not help ) Regards, -- Oguz YILMAZ UPDATE: The first problem is found. I have configured dhcrelay only on listening internel interface. It seems (of course) is should also listen to external interface for replies. It appears it is not important where the packet destined to. dhrelay will forward it to internal net. HOWEVER, I have deleted route on dhcpd server to reach 172.16.17.x subnet. It again tries to send reply to 172.16.17.81. Because it does not know the route it send it from default gateway to the internet. eth0: IP (tos 0x0, ttl 64, id 0, offset 0, flags [DF], proto: UDP (17), length: 328) 192.168.1.2.67 > 172.16.17.81.67: BOOTP/DHCP, Reply, length: 300, hops:1, xid:0x32830125, secs:3, flags: [none] (0x0000) eth0: Your IP: 172.16.17.11 eth0: Gateway IP: 172.16.17.81 eth0: Client Ethernet Address: 00:1e:68:06:eb:37 [|bootp] How can I force dhcpd to force to send replies to requesting IP? Because, it is not much meaningful to add routes to subnet we distribute IP for. Internet - dhcpd - 192.168.0.1 - SOMENET - 192.168.0.81 - dhcrelay - 172.16.17.0/24 192.168.0.1 has no route for 172.16.17.0 and has no interface directly attached to that net.

    Read the article

  • Latency issues over internet

    - by Stevo
    I have a Media Temple server running http://www.popsapp.com which I am having latency issues with. If I run ab -n 100 -c 10 http://www.popsapp.com/ from my local machine I get very bad stats e.g.: Connection Times (ms) min mean[+/-sd] median max Connect: 179 3375 2185.4 2837 12525 Processing: 0 505 693.3 229 4564 Waiting: 0 50 115.4 0 415 Total: 964 3880 2094.5 3159 12608 Whereas if I run it from a rackspace server I have I get this: Connection Times (ms) min mean[+/-sd] median max Connect: 75 76 3.3 75 84 Processing: 235 339 81.4 315 579 Waiting: 159 249 61.7 234 411 Total: 311 415 82.0 390 663 To me this looks like intermediate network issues, but I wouldn't have thought it could be this bad! Any ideas how I can improve it? Here's the trace route traceroute to www.popsapp.com (216.70.105.183), 64 hops max, 52 byte packets 1 192.168.2.1 (192.168.2.1) 3.738 ms 0.953 ms 1.418 ms 2 host-92-22-112-1.as13285.net (92.22.112.1) 27.409 ms 97.093 ms 78.858 ms 3 host-78-151-225-141.static.as13285.net (78.151.225.141) 61.830 ms 170.484 ms 113.288 ms 4 host-78-151-225-80.static.as13285.net (78.151.225.80) 101.513 ms host-78-151-225-22.static.as13285.net (78.151.225.22) 64.718 ms 47.309 ms 5 xe-11-1-0-rt001.sov.as13285.net (62.24.240.14) 98.381 ms 114.424 ms xe-11-1-0-rt001.the.as13285.net (62.24.240.6) 96.592 ms 6 host-78-144-1-59.as13285.net (78.144.1.59) 36.799 ms host-78-144-1-63.as13285.net (78.144.1.63) 178.426 ms host-78-144-1-61.as13285.net (78.144.1.61) 85.516 ms 7 xe-10-0-0-scr010.thn.as13285.net (78.144.0.224) 88.158 ms host-78-144-0-207.as13285.net (78.144.0.207) 35.132 ms host-78-144-0-153.as13285.net (78.144.0.153) 121.464 ms 8 limelight-pp-thn.as13285.net (78.144.3.6) 46.987 ms limelight-pp-sov.as13285.net (78.144.5.18) 108.025 ms 40.169 ms 9 tge11-1.fr4.lga.llnw.net (69.28.172.149) 109.603 ms ve6.fr4.lon.llnw.net (68.142.88.221) 121.681 ms 38.609 ms 10 tge11-1.fr4.lga.llnw.net (69.28.172.149) 111.981 ms 113.744 ms 111.711 ms 11 tge8-2.fr4.iad.llnw.net (69.28.189.34) 117.102 ms ve5.fr4.iad.llnw.net (69.28.171.214) 184.372 ms 146.178 ms 12 cr02-1-1.iad1.net2ez.com (65.97.48.254) 182.880 ms net2ez.tge2-2.fr4.iad.llnw.net (69.28.156.170) 150.489 ms 121.862 ms 13 65.97.50.26 (65.97.50.26) 184.620 ms cr02-1-1.iad1.net2ez.com (65.97.48.254) 156.136 ms 131.963 ms 14 65.97.50.26 (65.97.50.26) 124.899 ms 126.537 ms 123.322 ms 15 e1.4.as02.iad01.mtsvc.net (70.32.64.246) 134.647 ms 186.307 ms 211.059 ms 16 popsapp.com (216.70.105.183) 118.876 ms 113.189 ms vzx258.mediatemple.net (216.70.104.17) 131.012 ms Looks to me like there is significant delay across the limelight network. This would explain why the traceroute via my rackspace server doesn't suffer from the same delay as they will be using their own trunk.

    Read the article

  • Why /home folder is missing from my backup archive created by tar?

    - by Konstantin Pereyaslov
    So I'm doing full backup of my VPS using the following command (as root, of course): tar czvf 20120604.tar.gz / Everything seems to be fine, all files seem to appear in the list. The size of archive is 6 Gb and gunzipped version is 11 Gb which includes /home, because I totally have 11 Gb of data on VPS. But when I try actually to unpack archive, or open it using mc or WinRAR, there's no /home folder. And WinRAR tells 20120604.tar.gz - TAR+GZIP archive, unpacked size 894 841 346 bytes. It can't be WinRAR's bug, because when I type tar xzvf 20120604.tar.gz, /home folder isn't unpacked either. Why is /home folder missing from my archive? And what can I do to include it there? tar --version outputs the following: tar (GNU tar) 1.15.1

    Read the article

  • Is there a way to find what values comes from what file in HAL under Ubuntu?

    - by vava
    I've been playing with multitouch on my Thinkpad and read a few tutorials on how to setup it. One of them mentioned /usr/hal/fdi/policy/20thirdparty/11-x11-synaptics.fdi, I edited it and enabled SHMConfig through it. Later I found out about /etc/hal/policy/ directory and put some customization for my touchpad there as well in separate fdi file. But now it looks like touchpad doesn't care about my customizations. I have gsynaptec installed and can configure it though GUI, I can configure it with synclient but I can't set any values through fdi files. I even turned off SHMConfig, reverting 11-x11-synaptics,fdi file to it's original state but it seems like SHMConfig still enabled, otherwise I wouldn't be able to configure properties in runtime. So, I was thinking, maybe there's additional hal files I don't know about. How can I find them, particularly ones responsible for turning SHMConfig on?

    Read the article

  • Problems serving SVN over HTTPS on Ubuntu 10.04

    - by odd parity
    We've been experiencing some problems with our Subversion server after upgrading to Ubuntu 10.04. When trying to access a repository, regardless of client (I've tried git-svn and svn on Windows as well as svn on Ubuntu 10.04, from different computers and network locations), I get a 400 bad request. Here's the output from svn: svn: Server sent unexpected return value (400 Bad Request) in response to OPTIONS request for 'https://svn.example.org/svn/programs' Here are the relevant entries from the Apache logs (I'm running Apache 2.2): error.log [Mon Jun 14 11:29:31 2010] [error] [client x.x.x.x] request failed: error reading the headers ssl_access.log x.x.x.x - - [14/Jun/2010:11:29:28 +0200] "OPTIONS /svn/programs HTTP/1.1" 401 2643 "-" "SVN/1.6.6 (r40053) neon/0.29.0" x.x.x.x - - [14/Jun/2010:11:29:31 +0200] "ction-set/></D:options>OPTIONS /svn/programs HTTP/1.1" 400 644 "-" "SVN/1.6.6 (r40053) neon/0.29.0" If anyone has run into similar problems or could give me a pointer to track down the cause of this I'd be very grateful - I'd really like to avoid having to downgrade the box again.

    Read the article

  • Using wget to download pdf files from a site that requires cookies to be set

    - by matt74tm
    I want to access a newspaper site and then download their epaper copies (in PDF). The site requires me to login using my email address and password and then it permits me to access those PDF URLs. I'm having trouble 'setting my session' in wget. When I login into the site from my browser, it sets two cookie values: [email protected] Password=12345 I tried: wget --post-data "[email protected]&Password=12345" http://epaper.abc.com/login.aspx However, that just downloaded the login page and saved it locally The FORM on the login page has two fields: txtUserID txtPassword and radiobuttons like this: <input id="rbtnManchester" type="radio" checked="checked" name="txtpub" value="44"> Another button: <input id="rbtnLondon" type="radio" name="txtpub" value="64"> If I post this to the login.aspx page, I get the same output wget --post-data "[email protected]&txtPassword=12345&txtpub=44" http://epaper.abc.com/login.aspx If I do: --save-cookies abc_cookies.txt it doesnt seem to have anything other than the default content. For the last if I do --debug as well it says: ... Set-Cookie: ASP.NET_SessionId=05kphcn4hjmblq45qgnjoe41; path=/; HttpOnly ... Stored cookie epaper.abc.com -1 (ANY) / <session> <insecure> [expiry none] ASP.NET_SessionId 05kphcn4hjmblq45qgnjoe41 Length: 107253 (105K) [text/html] Saving to: `login.aspx' ... Saving cookies to abc_cookies.txt. However, abc_cookies.txt shows ONLY the following: # HTTP cookie file. # Generated by Wget on 2011-08-16 08:03:05. # Edit at your own risk. (Not sure why I'm not getting any responses on SO - perhaps SU is a better forum - http://stackoverflow.com/questions/7064171/using-wget-to-download-pdf-files-from-a-site-that-requires-cookies-to-be-set) EDIT 1 C:\Temp>wget --cookies=on --keep-session-cookies --save-cookies abc_cookies.txt --post-data "txtUserID=abc%40gmail.com&txtPassword=password&txtpub=44&chkbox=checkbox&submit.x=48&submit.y=7" http://epaper.abc.com/login.aspx --debug SYSTEM_WGETRC = c:/progra~1/wget/etc/wgetrc syswgetrc = C:\Program Files (x86)\GnuWin32/etc/wgetrc DEBUG output created by Wget 1.11.4 on Windows-MinGW. --2011-08-18 08:15:59-- http://epaper.abc.com/login.aspx Resolving epaper.abc.com... seconds 0.00, 999.999.99.99 Caching epaper.abc.com => 999.999.99.99 Connecting to epaper.abc.com|999.999.99.99|:80... seconds 0.00, connected. Created socket 300. Releasing 0x00a2ae80 (new refcount 1). ---request begin--- POST /login.aspx HTTP/1.0 User-Agent: Wget/1.11.4 Accept: */* Host: epaper.abc.com Connection: Keep-Alive Content-Type: application/x-www-form-urlencoded Content-Length: 100 ---request end--- [POST data: txtUserID=abc%40gmail.com&txtPassword=password&txtpub=44&chkbox=checkbox&submit.x=48&submit.y=7] HTTP request sent, awaiting response... ---response begin--- HTTP/1.1 200 OK Connection: keep-alive Date: Thu, 18 Aug 2011 02:46:17 GMT Server: Microsoft-IIS/6.0 X-Powered-By: ASP.NET X-AspNet-Version: 2.0.50727 Set-Cookie: ASP.NET_SessionId=owcrje55yl45kgmhn43gq145; path=/; HttpOnly Cache-Control: private Content-Type: text/html; charset=utf-8 Content-Length: 107253 ---response end--- 200 OK Registered socket 300 for persistent reuse. Stored cookie epaper.abc.com -1 (ANY) / <session> <insecure> [expiry none] ASP.NET_SessionId owcrje55yl45kgmhn43gq145 Length: 107253 (105K) [text/html] Saving to: `login.aspx.1' 100%[======================================================================================================================>] 107,253 24.9K/s in 4.2s 2011-08-18 08:16:05 (24.9 KB/s) - `login.aspx.1' saved [107253/107253] Saving cookies to abc_cookies.txt. Done saving cookies. C:\Temp>wget --referer=http://epaper.abc.com/login.aspx --cookies=on --load-cookies abc_cookies.txt --keep-session-cookies --save-cookies abc_cookies.txt http://epaper.abc.com/PagePrint/16_08_2011_001.pdf --debug SYSTEM_WGETRC = c:/progra~1/wget/etc/wgetrc syswgetrc = C:\Program Files (x86)\GnuWin32/etc/wgetrc DEBUG output created by Wget 1.11.4 on Windows-MinGW. Stored cookie epaper.abc.com -1 (ANY) / <session> <insecure> [expiry none] ASP.NET_SessionId owcrje55yl45kgmhn43gq145 --2011-08-18 08:16:12-- http://epaper.abc.com/PagePrint/16_08_2011_001.pdf Resolving epaper.abc.com... seconds 0.00, 999.999.99.99 Caching epaper.abc.com => 999.999.99.99 Connecting to epaper.abc.com|999.999.99.99|:80... seconds 0.00, connected. Created socket 300. Releasing 0x00598290 (new refcount 1). ---request begin--- GET /PagePrint/16_08_2011_001.pdf HTTP/1.0 Referer: http://epaper.abc.com/login.aspx User-Agent: Wget/1.11.4 Accept: */* Host: epaper.abc.com Connection: Keep-Alive Cookie: ASP.NET_SessionId=owcrje55yl45kgmhn43gq145 ---request end--- HTTP request sent, awaiting response... ---response begin--- HTTP/1.1 200 OK Connection: keep-alive Date: Thu, 18 Aug 2011 02:46:30 GMT Server: Microsoft-IIS/6.0 X-Powered-By: ASP.NET X-AspNet-Version: 2.0.50727 content-disposition: attachement; filename=Default_logo.gif Cache-Control: private Content-Type: image/GIF Content-Length: 4568 ---response end--- 200 OK Registered socket 300 for persistent reuse. Length: 4568 (4.5K) [image/GIF] Saving to: `16_08_2011_001.pdf' 100%[======================================================================================================================>] 4,568 7.74K/s in 0.6s 2011-08-18 08:16:14 (7.74 KB/s) - `16_08_2011_001.pdf' saved [4568/4568] Saving cookies to abc_cookies.txt. Done saving cookies. Contents of abc_cookies.txt epaper.abc.com FALSE / FALSE 0 ASP.NET_SessionId owcrje55yl45kgmhn43gq145

    Read the article

  • How do I insert a newline within a long formula using OpenOffice.org Math?

    - by Lekensteyn
    I've the following formula: (x^6+x^4+x^2+x+1)(x^7+x+1) = x^13+x^11+x^9+x^8+x^7+ x^7+x^5+x^3+x^3+x^2+x+ x^6+x^4+x^2+x+1 = x^13+x^11+x^9+x^8+2x^7+x^6+x^5+x^4+2x^3+2x^2+2x+1 Putting this in OpenOffice.org Math causes every line be concatenated, which I want to avoid. I've already tried putting newline between the lines, but it adds a strange question mark in the formula. Using matrices did not work for me either. I want to achieve a nicely formatted formula like this one (taken from FIPS 197 pdf):

    Read the article

  • How to find the /dev name of my USB device

    - by mustafa
    I am running Ubuntu 11 on VmWare on Windows XP. I want to format an SD card in Ubuntu. But, I can't figure out which /dev/xxx device the SD card is. I plug the card into the built-in socket of my laptop. I "safely remove" the device in Windows. Then, I "connect" the PCMCIA reader in VmWare. Now, I was supposing to see a new device like /dev/sdx. But, it doesn't appear :( How can I find what the name of my USB device's name and mount it? /var/log/message is empty. Here is the output of dmesg: [ 5268.927308] usb 2-1: new full speed USB device number 12 using uhci_hcd And, here is the last lines of /var/log/syslog: Oct 31 18:51:21 ubuntu kernel: [ 5268.927308] usb 2-1: new full speed USB device number 12 using uhci_hcd Oct 31 18:51:21 ubuntu mtp-probe: checking bus 2, device 12: "/sys/devices/pci0000:00/0000:00:11.0/0000:02:00.0/usb2/2-1" Oct 31 18:51:21 ubuntu mtp-probe: bus: 2, device: 12 was not an MTP device

    Read the article

  • How do I compare binary files in Linux?

    - by frustratedCmpNoLongerUser
    I need to compare two binary files and get the output in the form <fileoffset-hex <file1-byte-hex <file2-byte-hex for every different byte. So if file1.bin is 00 90 00 11 in binary form and file2.bin is 00 91 00 10 I want to get something like 00000001 90 91 00000003 11 10 What is the easiest way to accomplish the goal? Standard tool? Some third-party tool? (Note: cmp -l should be killed with fire, it uses a decimal system for offsets and octal for bytes.)

    Read the article

  • Anyone had any issues getting a disk to start on a Walrus storage sytem?

    - by Peter NUnn
    Hi folks, I'm trying to get a Eucalyptus system up and running and have managed to get the cloud controller and node controller running fine, with an instance running in the cloud system, but without any persistent storage. When I try and create a volume I get euca-create-volume -s 10 -z cluster1 VOLUME vol-5F5D0659 10 creating 2010-05-31T09:10:11.408Z but when I try and see the volume I get euca-describe-volumes VOLUME vol-5F5D0659 10 cluster1 failed 2010-05-31T09:10:11.408Z VOLUME vol-5FE9065E 10 cluster1 failed 2010-05-31T09:02:56.721Z I've dug all over the place, but can't seem to turn up a reason the creation would fail or where to start looking to see what the issue might be. Anyone have any ideas where to even start looking for the answer to this? Ta Peter.

    Read the article

  • Why is this static routing not working ?

    - by geeko
    Greeting gurus, I'm trying to develop a DHCP enforcement extension like Microsoft NAP. My trick to block dynamic-IP requesting machines (that don't meet certain policy) is to strip the default gateway (no default gateway) stated in the IP lease and set the lease subnet mask to 255.255.255.255. Now I need the blocked machines to be able to reach some specific locations (IPs) on the network. To allow for this, I'm including some static routes in the lease. For example, I'm including 10.10.10.11 via router 10.10.10.254 (the one to which the blocked machine that needs to access 10.10.10.11 is connected). Unfortunately, as soon as I set the default gateway to nothing, blocked machines cannot reach any of the added static routes. I also tried classless static routes. Any ideas ? any one knows how MS NAP actually do it ? Geeko

    Read the article

  • how to run an AFS file server on a specific ethernet card (in Debian)

    - by listboss
    I have a linux box running Debian server with minimal number of packages (so no GUI for network management). The box has two ethernet cards, one of which (eth0) is connected to a Mac OSX computer using a cross-cable. I can bring up eth0 and assign a static ip (10.10.11.16) to it. This way I can ssh to the box through the cross-cable. This is what I run on Linux box: ifconfig eth0 10.10.11.16 netmask 255.255.255.0 up I also installed/started a file server (AFS) on Debian. So far, the file server can only be accessed through eth1 which is exposed to my home LAN and www. My goal is to set up the file server so that it's only visible through eth0. Is this possible? and if yes, how can I do it?

    Read the article

  • X11 for apache user

    - by fuenfundachtzig
    We are using inkscape to convert SVG images uploaded to our server via a web form. For this inkscape offers a batch mode via the -z option, but this batch mode has a flaw: When inkscape is run by the apache user, it breaks saying $ inkscape -z -W drawing.svg X11 connection rejected because of wrong authentication. The application 'inkscape' lost its connection to the display localhost:11.0; most likely the X server was shut down or you killed/destroyed the application. If you do the same as a normal user you also get errors: Xlib: connection to "localhost:11.0" refused by server Xlib: PuTTY X11 proxy: MIT-MAGIC-COOKIE-1 data did not match (inkscape:24050): Gdk-CRITICAL **: gdk_display_list_devices: assertion `GDK_IS_DISPLAY (display)' failed 301.27942 But at least inkscape gives the correct answer (here the number stating the width of the image). Does somebody know how to make this also work for the apache user? Does it make sense to authorize apache to use X (if so how)? In any case it doesn't feel like the right solution...

    Read the article

  • Why does 1GBit card have output limited to 80 MiB ?

    - by Gallus
    I'm trying to utilize maximal bandwidth provided by my 1GiB network card, but it's always limited to 80MiB (real megabytes). What can be the reason? Card description (lshw output): description: Ethernet interface product: DGE-530T Gigabit Ethernet Adapter (rev 11) vendor: D-Link System Inc physical id: 0 bus info: pci@0000:03:00.0 logical name: eth1 version: 11 serial: 00:22:b0:68:70:41 size: 1GB/s capacity: 1GB/s width: 32 bits clock: 66MHz capabilities: pm vpd bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation The card is placed in following PCI slot: *-pci:2 description: PCI bridge product: 82801 PCI Bridge vendor: Intel Corporation physical id: 1e bus info: pci@0000:00:1e.0 version: 92 width: 32 bits clock: 33MHz capabilities: pci subtractive_decode bus_master cap_list The PCI isn't any PCI Express right? It's a legacy PCI slot? So maybe this is the reason? OS is a linux.

    Read the article

  • Chrome: Black Screen of Death

    - by davidsinjaya
    I dont know when it started to happen. The screen will turn into full black when a page include javascript (I think so). I cannot open Youtube videos, but I can still see the source code and the pointer to find links and buttons and I can hear the sound of video. I have tried to clear my cache and reinstalled to the latest version, but nothing seems work. Moreover, I have disabled the Pepperflash Player as well, but it did not help. This my chrome version Google Chrome 22.0.1229.79 (Official Build 158531) OS Windows WebKit 537.4 (@129177) JavaScript V8 3.12.19.11 Flash 11.3.31.331 Please help.

    Read the article

  • Building boost 1.42 on FreeBSD 6.3

    - by Ivan Perekluyev
    Hi, i need to build mapnik on freebsd 6.3, but port marked as 'broken', so i forced to build it from source. With boost 1.41 (which is in ports) mapnik doesn't build. somewhere in internet, i found that mapnik successfully builded with boost 1.42. So, i download patch from wiki.freebsd.org/BoostPortingProject andd apply it: wget http://alexanderchuranov.com/boost-port/boost-from-1.41-to-1.42-2010-02-16-17-11.diff cd /usr/ports patch -p0 -i ~/boost-from-1.41-to-1.42-2010-02-16-17-11.diff after that, i trying to install boost-all metaport, but its failed. cd devel/boost-all make install 2>&1 | tee build.log tail -n 100 build.log > short_build.log Build.log (attention, 5m !): dl.dropbox.com/u/7365614/build.log Short build log: http://paste.pocoo.org/show/224474/ Thanks!

    Read the article

< Previous Page | 100 101 102 103 104 105 106 107 108 109 110 111  | Next Page >