Search Results

Search found 11364 results on 455 pages for 'port blocking'.

Page 104/455 | < Previous Page | 100 101 102 103 104 105 106 107 108 109 110 111  | Next Page >

• DDWRT VLAN Without internet

  - by user148888

  Hey i have WRT54G with DD-WRT v24-sp2 firmware. i got this scenario Vlan0 port 2,3,4 172.168.1.1/24 vlan1 Wan port Vlan2 port 1 172.168.2.1/24 i can ping from vlan0 to vlan2 but vlan2 can't ping to vlan0 iptables -I FORWARD -i vlan2 -o vlan1 -j DROP i use this to prevent vlan2 to have internet cuz i don't want to share my internet to vlan2 i just want to share local network betwen vlan1 and vlan2.. any help please :S:S:S

  Read the article

• Using QoS to prioritize IP addresses

  - by Tristan

  I have a Western Digital N900 router. I was hoping I'd be able to throttle users based on their MAC address with it, which isn't possible sadly. Seems simple in principle though, duh. The battle against bandwidth hogging roomates rages on. Could I just set the local IP range to their IP, and then set the Local port range to every single port in existence. Then prioritize their IP to lower than mine? Will this work? What are all the ports? And what's the difference between Local and Remote IPs or Ports? Name: Roomate, Priority: Low, Protocol: TCP or UDP ??, Local IP Range: .101 to .101, Local Port Range: 0 to infinity, Remote IP Range: ? to ?, Remote Port Range: ? to ?

  Read the article

• openwrt uses a single interface bridge?

  - by timbo

  My understanding of bridging is that it ties together two interfaces at layer 2. I am looking at a Ubiquiti Nanostation2 running OpenWRT that has an ethernet port 'eth0' and a wifi port 'ath0'. The ethernet port (the 'wan' port) is not part of the bridge and the bridge is just a single interface. Can anyone clarify this? - seems very different to Ubuntu. /etc/config/network: config 'interface' 'loopback' option 'ifname' 'lo' option 'proto' 'static' option 'ipaddr' '127.0.0.1' option 'netmask' '255.0.0.0' config 'interface' 'wan' option 'ifname' 'eth0' option 'proto' 'dhcp' config 'interface' 'wifi' option 'ipaddr' '192.168.13.1' option 'type' 'bridge' option 'proto' 'static' option 'netmask' '255.255.255.0' option 'ifname' 'wifi0'

  Read the article

• SSH: Connection Reset by Peer

  - by hopeless

  I have a Solaris 10 server on another network. I can ping it and telnet to it, but ssh doesn't connect. PuTTY log contains nothing of interest (they both negotiate to ssh v2) and then I get "Event Log: Network error: Software caused connection abort". ssh is defintely running: svcs -a | grep ssh online 12:12:04 svc:/network/ssh:default Here's an extract from the server's /var/adm/messages (anonymised) Jun 8 19:51:05 ******* sshd[26391]: [ID 800047 auth.crit] fatal: Read from socket failed: Connection reset by peer However, if I telnet to the box, I can login to ssh locally. I can also ssh to other (non-Solaris) machines on that network fine so I don't believe that it's a network issue (though, since I'm a few hundred miles away, I can't be sure). The server's firewall is disabled, so that shouldn't be a problem root@******** # svcs -a | grep -i ipf disabled Apr_27 svc:/network/ipfilter:default Any ideas what I should start checking? Update: Based on the feedback below, I've run sshd in debug mode. Here's the client output: $ ssh -vvv root@machine -p 32222 OpenSSH_5.0p1, OpenSSL 0.9.8h 28 May 2008 debug2: ssh_connect: needpriv 0 debug1: Connecting to machine [X.X.X.X] port 32222. debug1: Connection established. debug1: identity file /home/lawrencj/.ssh/identity type -1 debug1: identity file /home/lawrencj/.ssh/id_rsa type -1 debug1: identity file /home/lawrencj/.ssh/id_dsa type -1 debug1: Remote protocol version 2.0, remote software version Sun_SSH_1.1 debug1: no match: Sun_SSH_1.1 debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.0 debug2: fd 3 setting O_NONBLOCK debug1: SSH2_MSG_KEXINIT sent Read from socket failed: Connection reset by peer And here's the server output: root@machine # /usr/lib/ssh/sshd -d -p 32222 debug1: sshd version Sun_SSH_1.1 debug1: read PEM private key done: type RSA debug1: private host key: #0 type 1 RSA debug1: read PEM private key done: type DSA debug1: private host key: #1 type 2 DSA debug1: Bind to port 32222 on ::. Server listening on :: port 32222. debug1: Bind to port 32222 on 0.0.0.0. Server listening on 0.0.0.0 port 32222. debug1: Server will not fork when running in debugging mode. Connection from 1.2.3.4 port 2652 debug1: Client protocol version 2.0; client software version OpenSSH_5.0 debug1: match: OpenSSH_5.0 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-Sun_SSH_1.1 debug1: list_hostkey_types: ssh-rsa,ssh-dss debug1: Failed to acquire GSS-API credentials for any mechanisms (No credentials were supplied, or the credentials were unavailable or inaccessible Unknown code 0 ) debug1: SSH2_MSG_KEXINIT sent Read from socket failed: Connection reset by peer debug1: Calling cleanup 0x4584c(0x0) This line seems a likely candidate: debug1: Failed to acquire GSS-API credentials for any mechanisms (No credentials were supplied, or the credentials were unavailable or inaccessible

  Read the article

• WSS and CAG , _layout pages break

  - by Mike

  Alright, I've searched everywhere and I cannot find the answer, due to the rarity of our setup. WSS 3.0/IIS 6.0/WinServer 2003 We have a sharepoint site that is in good shape, almost. Its TCP and SSL port are uncommon and need to be rerouted to work properly. This is where the Citrix Access Gateway (CAG) comes in play. It will redirect any request from URL (something.something.com) to the correct SSL port on the correct server. My AAM is configured to Default something.something.com and nothing else, since the CAG will provide the port. We use FBA, and require SSL. This works perfectly for everything that is safe or that is anything that an end user can see, but if I try to add a webpart, it errors out. Whereas if I add it internally, or bypass the CAG the webpart adds fine. The same goes for most of the _layouts pages, like _layouts/new.aspx. If I add a Link List/Doc library on the something.something.com, it errors out (Page cannot be displayed) and the page won't display, but if I try it with an internal address it will work fine. I found that if I am trying to add something or doing anything administrative, the site will navigate to the pages that I need to go to fine, but when i actually ADD something the URL will change from something.something.com to something.something.com:SSLport, thus erroring out the site. The URL with the SSL port shows on the Site URL when navigating to Site Settings. However, if I bypass the CAG, using the internal address the _layouts page works like a charm and i can add anything. All the CAG does is reroute a DNS request to the provided server and port. I've tried reextending the application, no luck same thing. I've tried changing the AAM to hide the port and the CAG rejects it. I've tried to recreate a new webapp/site collection with the same rules on the CAG, same thing occurs. Correct me if I'm wrong, and please provide me with some feedback and answers. Any suggestions would be very appreciated. Is it the CAG or the Alternate Access Mappings (AAM)?

  Read the article

• Serving Meteor on main domain and Apache on subdomain independently

  - by kinologik

  I'm running a Meteor server on my Ubuntu server. But problems arise when I try to have Apache serving a subdomain on the same server. main.domain.com - Meteor sub.domain.com - Apache Meteor is running on port 80. I have previously tried to have Meteor run on port 3000 and served in reverse proxy with Nginx, but Meteor started to behave badly (tcp/websockets issues) and I spent too many evenings and nights to persist for my own sake. So I reverted my setup to have Meteor being the main server (app works fine), and then install Apache the serve my subdomain. The problem is I cannot have Apache serve on port 80 too since it seems to overrun my Meteor server. From experience, I try to stay away from reverse-proxying Meteor, but I'm not knowledgeable enough to get Apache to dedicate itself to my subdomain and without overwhelming "everything port 80" on my server. How can I have both services behave with each other in this kind of setup?

  Read the article

• Tomcat IIS 7 Integration gives 503 errors on all requests.

  - by Yvan JANSSENS

  Hi, After many attempts to install Tomcat on IIS 7, I finally managed to get it working. At least I think so :-S. I finally got the 500 errors away, by setting the correct permissions. The only thing that doesn't work is ... serving stuff: neither regular stuff (like ASP, HTML files, or directory browsing) or Tomcat things work. Here are my configs: Worker.properties # The workers that your plugins should create and work with # worker.list=worker1 #------ DEFAULT ajp13 WORKER DEFINITION ------------------------------ #--------------------------------------------------------------------- # Defining a worker named ajp13 and of type ajp13 # Note that the name and the type do not have to match. # worker.worker1.port=8009 worker.worker1.host=127.0.0.1 worker.worker1.type=ajp13 URIWorkerMap.properties /|/*=worker1 # Exclude the subdirectory static: !/static|/*=worker1 # Exclude some suffixes: !*.html=worker1 !*.asp=worker1 Server.xml <?xml version='1.0' encoding='utf-8'?> <!-- Licensed to the Apache Software Foundation (ASF) under one or more contributor license agreements. See the NOTICE file distributed with this work for additional information regarding copyright ownership. The ASF licenses this file to You under the Apache License, Version 2.0 (the "License"); you may not use this file except in compliance with the License. You may obtain a copy of the License at http://www.apache.org/licenses/LICENSE-2.0 Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License for the specific language governing permissions and limitations under the License. --> <!-- Note: A "Server" is not itself a "Container", so you may not define subcomponents such as "Valves" at this level. Documentation at /docs/config/server.html --> <Server port="8005" shutdown="SHUTDOWN"> <!--APR library loader. Documentation at /docs/apr.html --> <Listener className="org.apache.catalina.core.AprLifecycleListener" SSLEngine="on" /> <!--Initialize Jasper prior to webapps are loaded. Documentation at /docs/jasper-howto.html --> <Listener className="org.apache.catalina.core.JasperListener" /> <!-- Prevent memory leaks due to use of particular java/javax APIs--> <Listener className="org.apache.catalina.core.JreMemoryLeakPreventionListener" /> <!-- JMX Support for the Tomcat server. Documentation at /docs/non-existent.html --> <Listener className="org.apache.catalina.mbeans.ServerLifecycleListener" /> <Listener className="org.apache.catalina.mbeans.GlobalResourcesLifecycleListener" /> <!-- Global JNDI resources Documentation at /docs/jndi-resources-howto.html --> <GlobalNamingResources> <!-- Editable user database that can also be used by UserDatabaseRealm to authenticate users --> <Resource name="UserDatabase" auth="Container" type="org.apache.catalina.UserDatabase" description="User database that can be updated and saved" factory="org.apache.catalina.users.MemoryUserDatabaseFactory" pathname="conf/tomcat-users.xml" /> </GlobalNamingResources> <!-- A "Service" is a collection of one or more "Connectors" that share a single "Container" Note: A "Service" is not itself a "Container", so you may not define subcomponents such as "Valves" at this level. Documentation at /docs/config/service.html --> <Service name="Catalina"> <!--The connectors can use a shared executor, you can define one or more named thread pools--> <!-- <Executor name="tomcatThreadPool" namePrefix="catalina-exec-" maxThreads="150" minSpareThreads="4"/> --> <!-- A "Connector" represents an endpoint by which requests are received and responses are returned. Documentation at : Java HTTP Connector: /docs/config/http.html (blocking & non-blocking) Java AJP Connector: /docs/config/ajp.html APR (HTTP/AJP) Connector: /docs/apr.html Define a non-SSL HTTP/1.1 Connector on port 8080 --> <Connector port="8080" protocol="HTTP/1.1" connectionTimeout="20000" redirectPort="8443" /> <!-- A "Connector" using the shared thread pool--> <!-- <Connector executor="tomcatThreadPool" port="8080" protocol="HTTP/1.1" connectionTimeout="20000" redirectPort="8443" /> --> <!-- Define a SSL HTTP/1.1 Connector on port 8443 This connector uses the JSSE configuration, when using APR, the connector should be using the OpenSSL style configuration described in the APR documentation --> <!-- <Connector port="8443" protocol="HTTP/1.1" SSLEnabled="true" maxThreads="150" scheme="https" secure="true" clientAuth="false" sslProtocol="TLS" /> --> <!-- Define an AJP 1.3 Connector on port 8009 --> <Connector port="8009" protocol="AJP/1.3" redirectPort="8443" /> <!-- An Engine represents the entry point (within Catalina) that processes every request. The Engine implementation for Tomcat stand alone analyzes the HTTP headers included with the request, and passes them on to the appropriate Host (virtual host). Documentation at /docs/config/engine.html --> <!-- You should set jvmRoute to support load-balancing via AJP ie : <Engine name="Catalina" defaultHost="localhost" jvmRoute="jvm1"> --> <Engine name="Catalina" defaultHost="localhost"> <!--For clustering, please take a look at documentation at: /docs/cluster-howto.html (simple how to) /docs/config/cluster.html (reference documentation) --> <!-- <Cluster className="org.apache.catalina.ha.tcp.SimpleTcpCluster"/> --> <!-- The request dumper valve dumps useful debugging information about the request and response data received and sent by Tomcat. Documentation at: /docs/config/valve.html --> <!-- <Valve className="org.apache.catalina.valves.RequestDumperValve"/> --> <!-- This Realm uses the UserDatabase configured in the global JNDI resources under the key "UserDatabase". Any edits that are performed against this UserDatabase are immediately available for use by the Realm. --> <Realm className="org.apache.catalina.realm.UserDatabaseRealm" resourceName="UserDatabase"/> <!-- Define the default virtual host Note: XML Schema validation will not work with Xerces 2.2. --> <Host name="localhost" appBase="webapps" unpackWARs="true" autoDeploy="true" xmlValidation="false" xmlNamespaceAware="false"> <!-- SingleSignOn valve, share authentication between web applications Documentation at: /docs/config/valve.html --> <!-- <Valve className="org.apache.catalina.authenticator.SingleSignOn" /> --> <!-- Access log processes all example. Documentation at: /docs/config/valve.html --> <!-- <Valve className="org.apache.catalina.valves.AccessLogValve" directory="logs" prefix="localhost_access_log." suffix=".txt" pattern="common" resolveHosts="false"/> --> </Host> </Engine> </Service> </Server> http://localhost:8080 is working, I can view the apps and configure them there... I'm quite new to IIS 7, I used to work with IIS 6. Thanks in advance, Yvan

  Read the article

• LFTP when used with proxies doesn't work

  - by user2949465

  can't seem to use LFTP with proxies that require authentification correctly on my Ubuntu server. When I use it with proxy that doesn't require username/password everything seems fine: lftp lftp :~> set http:proxy http://HOST:PORT lftp :~> set ftp:proxy http://HOST:PORT lftp :~> open username:[email protected] lftp [email protected]:~> get file.ext file.ext 36352 bytes transferred in 10 seconds (3.5K/s) lftp [email protected]:~> exit but when I have to put username/password there is a problem: lftp lftp :~> set http:proxy http://proxylogin:proxypass@HOST:port lftp :~> set ftp:proxy http://proxylogin:proxypass@HOST:port lftp :~> open ftp://ftpuser:[email protected] answer: cd: Access failed: 401 Authentication Required (~) please someone help!

  Read the article

• Plone with Apache Proxy

  - by churnd

  I have a plone zinstance set up through Apache Proxy on OS X Server 10.5. The server is set up with a single vhost on port 80, with Proxy & Proxypass directives to the Plone zinstance: ProxyPass / http://localhost:8080/VirtualHostBase/http/server:80/Plone/VirtualHostRoot/ ProxyPassReverse / http://localhost:8080/VirtualHostBase/http/server:80/Plone/VirtualHostRoot/ However, I have some static HTML and PHP content that I want to display in an iframe via the plone site. I'm thinking I'll need to set up another vhost on a different port, then just specify the port # inline?

  Read the article

• SSL in IIS 7 on a subdomain in a web farm

  - by justjoshingyou

  I have been having one of the most frustrating days in my entire IT career. I am trying to install an SSL certificate on a subdomain in a web farm. http://shop.mydomain.com needs to ALWAYS be forced to https://shop.mydomain.com I have a temporary cert issued from verisign on shop.mydomain.com I have installed the cert on the server. The website for shop.mydomain.com is set as a host header in IIS with the DNS entry pointed to the same IP as mydomain.com - which is our load balancer. I actually have 2 load balancers (as needed by our ISP). One redirects all traffic on port 80 out to the different servers on port 80. The other pushes out port 443 to the servers on port 443. shop.mydomain.com is to be the only site protected by SSL at this time. When I add the binding and I navigate to https://shop.mydomain.com it pops up with a warning about the cert being invalid (assumed because this is a test cert), and then it sends the user to http. So, I checked the box "Require SSL and it redirects to http://shop.mydomain.com/default.aspx and displayes an ASP.NET 404 error message. (not the IIS 404 error) I tried removing the binding on the site to port 80 as well with no luck. I am nearly ready to crawl under my desk into the fetal position. How on earth do I make this work? I can't even get it to work on one machine, let alone in the load balanced environment.

  Read the article

• Cisco ASA - Enable communication between same security level

  - by Conor

  I have recently inherited a network with a Cisco ASA (running version 8.2). I am trying to configure it to allow communication between two interfaces configured with the same security level (DMZ-DMZ) "same-security-traffic permit inter-interface" has been set, but hosts are unable to communicate between the interfaces. I am assuming that some NAT settings are causing my issue. Below is my running config: ASA Version 8.2(3) ! hostname asa enable password XXXXXXXX encrypted passwd XXXXXXXX encrypted names ! interface Ethernet0/0 switchport access vlan 400 ! interface Ethernet0/1 switchport access vlan 400 ! interface Ethernet0/2 switchport access vlan 420 ! interface Ethernet0/3 switchport access vlan 420 ! interface Ethernet0/4 switchport access vlan 450 ! interface Ethernet0/5 switchport access vlan 450 ! interface Ethernet0/6 switchport access vlan 500 ! interface Ethernet0/7 switchport access vlan 500 ! interface Vlan400 nameif outside security-level 0 ip address XX.XX.XX.10 255.255.255.248 ! interface Vlan420 nameif public security-level 20 ip address 192.168.20.1 255.255.255.0 ! interface Vlan450 nameif dmz security-level 50 ip address 192.168.10.1 255.255.255.0 ! interface Vlan500 nameif inside security-level 100 ip address 192.168.0.1 255.255.255.0 ! ftp mode passive clock timezone JST 9 same-security-traffic permit inter-interface same-security-traffic permit intra-interface object-group network DM_INLINE_NETWORK_1 network-object host XX.XX.XX.11 network-object host XX.XX.XX.13 object-group service ssh_2220 tcp port-object eq 2220 object-group service ssh_2251 tcp port-object eq 2251 object-group service ssh_2229 tcp port-object eq 2229 object-group service ssh_2210 tcp port-object eq 2210 object-group service DM_INLINE_TCP_1 tcp group-object ssh_2210 group-object ssh_2220 object-group service zabbix tcp port-object range 10050 10051 object-group service DM_INLINE_TCP_2 tcp port-object eq www group-object zabbix object-group protocol TCPUDP protocol-object udp protocol-object tcp object-group service http_8029 tcp port-object eq 8029 object-group network DM_INLINE_NETWORK_2 network-object host 192.168.20.10 network-object host 192.168.20.30 network-object host 192.168.20.60 object-group service imaps_993 tcp description Secure IMAP port-object eq 993 object-group service public_wifi_group description Service allowed on the Public Wifi Group. Allows Web and Email. service-object tcp-udp eq domain service-object tcp-udp eq www service-object tcp eq https service-object tcp-udp eq 993 service-object tcp eq imap4 service-object tcp eq 587 service-object tcp eq pop3 service-object tcp eq smtp access-list outside_access_in remark http traffic from outside access-list outside_access_in extended permit tcp any object-group DM_INLINE_NETWORK_1 eq www access-list outside_access_in remark ssh from outside to web1 access-list outside_access_in extended permit tcp any host XX.XX.XX.11 object-group ssh_2251 access-list outside_access_in remark ssh from outside to penguin access-list outside_access_in extended permit tcp any host XX.XX.XX.10 object-group ssh_2229 access-list outside_access_in remark http from outside to penguin access-list outside_access_in extended permit tcp any host XX.XX.XX.10 object-group http_8029 access-list outside_access_in remark ssh from outside to internal hosts access-list outside_access_in extended permit tcp any host XX.XX.XX.13 object-group DM_INLINE_TCP_1 access-list outside_access_in remark dns service to internal host access-list outside_access_in extended permit object-group TCPUDP any host XX.XX.XX.13 eq domain access-list dmz_access_in extended permit ip 192.168.10.0 255.255.255.0 any access-list dmz_access_in extended permit tcp any host 192.168.10.29 object-group DM_INLINE_TCP_2 access-list public_access_in remark Web access to DMZ websites access-list public_access_in extended permit object-group TCPUDP any object-group DM_INLINE_NETWORK_2 eq www access-list public_access_in remark General web access. (HTTP, DNS & ICMP and Email) access-list public_access_in extended permit object-group public_wifi_group any any pager lines 24 logging enable logging asdm informational mtu outside 1500 mtu public 1500 mtu dmz 1500 mtu inside 1500 no failover icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 60 global (outside) 1 interface global (dmz) 2 interface nat (public) 1 0.0.0.0 0.0.0.0 nat (dmz) 1 0.0.0.0 0.0.0.0 nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface 2229 192.168.0.29 2229 netmask 255.255.255.255 static (inside,outside) tcp interface 8029 192.168.0.29 www netmask 255.255.255.255 static (dmz,outside) XX.XX.XX.13 192.168.10.10 netmask 255.255.255.255 dns static (dmz,outside) XX.XX.XX.11 192.168.10.30 netmask 255.255.255.255 dns static (dmz,inside) 192.168.0.29 192.168.10.29 netmask 255.255.255.255 static (dmz,public) 192.168.20.30 192.168.10.30 netmask 255.255.255.255 dns static (dmz,public) 192.168.20.10 192.168.10.10 netmask 255.255.255.255 dns static (inside,dmz) 192.168.10.0 192.168.0.0 netmask 255.255.255.0 dns access-group outside_access_in in interface outside access-group public_access_in in interface public access-group dmz_access_in in interface dmz route outside 0.0.0.0 0.0.0.0 XX.XX.XX.9 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy http server enable http 192.168.0.0 255.255.255.0 inside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 telnet timeout 5 ssh 192.168.0.0 255.255.255.0 inside ssh timeout 20 console timeout 0 dhcpd dns 61.122.112.97 61.122.112.1 dhcpd auto_config outside ! dhcpd address 192.168.20.200-192.168.20.254 public dhcpd enable public ! dhcpd address 192.168.0.200-192.168.0.254 inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics host threat-detection statistics access-list no threat-detection statistics tcp-intercept ntp server 130.54.208.201 source public webvpn ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect ip-options inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp !

  Read the article

• Why is the link between my switch and my router always negotiating half-duplex mode?

  - by Massimo

  I have a Cisco 2950 switch which has one of its ports connected to an Internet router provided by my ISP; I have no access to the router configuration, but I manage the switch. If I leave all switch ports with their default setup (auto-negotiation of speed and duplex mode), this link always connects at 100 MBit/s, but in half-duplex mode. I've tried replacing the cable, and also moving the link to another switch port: the result is always the same. A different device connected to the same port (or to any switch port, really) shows no problem at all. It could be guesed that someone configured the router to only connect in half-duplex mode... BUT, here's the catch: if I manually force the switch port to full-duplex mode (duplex full in the interface configuration), the link goes up, stays up and is completely stable. So: The connection is not forced to half-duplex mode by the router, otherwise it would not connect at all if I force the switch end to full-duplex. There is no actual link problem, otherwise the full-duplex connection would not go up or would at least show some errors. But if I leave the port free to auto-negotiate, it always connects in half-duplex mode. Why?

  Read the article

• nginx + varnish + apache differente IPs in VirtualHost Apache

  - by zeusgod

  Hi, My idea is put NGINX as proxy to redirect to Varnish (cache static content) and then proxy to apache with a lot of VirtualHost in different IPs. My problems is that I would know how can configure Varnish to send access to correct IP, I am going explain: NGINX: Listen in: 10.10.10.10, 20.20.20.20 and 30.30.30.30 on ports: 80 and 443 Proxy redirect to Varnish 10.10.10.10:8080, 20.20.20.20:8080 and 30.30.30.30:8080 Varnish: Port: 8080 - THIS IS THE PROBLEM Proxy content not static to Apache on port 8000 - THIS IS THE OTHER PROBLEM Apache2: Listen in: 10.10.10.10:8000, 20.20.20.20:8000 and 30.30.30.30:8000 Response correct VirtualHost This is the idea. When I try with one IP only, all work correctly, because Varnish is only listen in one IP and port and send to backend in one IP and port too. Could you help me to configure Varnish or there is a best way to configure similar scenario please?

  Read the article

• Can not access IIS7 website externally - but can locally

  - by mactruck

  I have 2 websites, site A running on port 80 and site B configured to run on port 8080. I can access site A no problem, but site B I can only access from the local web server machine. Externally it is not accessable, I have tried the url and ip and neither work. I have tried different configuring on port 8081 as a test and that didnt work either. What IIS settings should I look at?

  Read the article

• How do I connect to MySQL when it's setting behind 2 layers of ssh?

  - by David Corley

  I have a MySQL server sitting behind a bastion server that I wish to connect to from my local machine. Ideally I want to port-forward the MySQL port (3316 in this case) to a local port on my machine. I've tried plink -ssh -L 3306:my.sql.ip.address:3316 my.bastion.server ,but this is not working. I've got one ssh login for the bastion server and another login for the machine mysql server is running on.

  Read the article

• Anything such as a usb laptop charger?

  - by iNinja

  I am looking for a laptop charger that requires no power outlet but instead utilizes a usb port of another computer to charge my laptop. That is, I am seeking a usb-to-laptop port charger, NOT power outlet-to-laptop's usb charger. Is such a product even possible? I am guessing no since the usb port would not be able to supply enough electricity to power the laptop, even to maintain the battery (not charge it).

  Read the article

• apache name virtual host - two domains and SSL

  - by Tom

  I'm trying to setup Apache(2.2.3) to run two websites with SSL using both different domains and IP addresses. Both websites run fine on port 80 but when I tried to enable SSL for website2 I get a ssl_error_bad_cert_domain error; website2 picks up the SSL cert for website1. Here is my setup in httpd.conf: # Website1 NameVirtualHost 192.168.10.1:80 <VirtualHost 192.168.10.1:80> DocumentRoot /var/www/html ServerName www.website1.org </VirtualHost> NameVirtualHost 192.168.10.1:443 <VirtualHost 192.168.10.1:443> SSLEngine On SSLCertificateFile conf/ssl/website1.cer SSLCertificateKeyFile conf/ssl/website1.key </VirtualHost> # Website2 NameVirtualHost 192.168.10.2:80 <VirtualHost 192.168.10.2:80> DocumentRoot /var/www/html/chart ServerName www.website2.org </VirtualHost> NameVirtualHost 192.168.10.2:443 <VirtualHost 192.168.10.2:443> SSLEngine On SSLCertificateFile conf/ssl/website2.cer SSLCertificateKeyFile conf/ssl/website2.key </VirtualHost> Update: In answer to Shane (this wouldn't fit in comment box) here is the output from apachectl -S: VirtualHost configuration: 192.168.10.2:80 is a NameVirtualHost default server www.website2.org (/etc/httpd/conf/httpd.conf:1033) port 80 namevhost www.website2.org (/etc/httpd/conf/httpd.conf:1033) 192.168.10.2:443 is a NameVirtualHost default server bogus_host_without_reverse_dns (/etc/httpd/conf/httpd.conf:1040) port 443 namevhost bogus_host_without_reverse_dns (/etc/httpd/conf/httpd.conf:1040) 192.168.10.1:80 is a NameVirtualHost default server www.website1.org (/etc/httpd/conf/httpd.conf:1017) port 80 namevhost www.website1.org (/etc/httpd/conf/httpd.conf:1017) 192.168.10.1:443 is a NameVirtualHost default server bogus_host_without_reverse_dns (/etc/httpd/conf/httpd.conf:1024) port 443 namevhost bogus_host_without_reverse_dns (/etc/httpd/conf/httpd.conf:1024) wildcard NameVirtualHosts and _default_ servers: _default_:443 192.168.10.1 (/etc/httpd/conf.d/ssl.conf:81) Syntax OK

  Read the article

• Installing TKInter for Python 2.6.5

  - by Azfar

  Well today's been a bit of shock. After running port -v selfupdate followed by an attempt to run sudo port install py26-ipython MacPorts went around installing a whole host of stuff, including updating my Python from 2.6.4 to 2.6.5. It's nice but unexpected in a creepy way. So I tried to install TKInter using MacPorts with port search tkinter yielding: py-tkinter @2.4.6 (python, graphics) Python bindings to the Tk widget set py25-tkinter @2.5.4 (python, graphics) This is a stub. tkinter is now built with python25 Found 2 ports. So I tried sudo port install py25-tkinter and then it tries to install Python 2.5.5. There must be an easier way to install TkInter without being faffed around... help please?

  Read the article

• How to monitor traffic on certain ports with ntop

  - by Claudiu

  How to configure ntop so I can get the amount of upload traffic sent through a certain port ? I've added port in ntop/protocol.list, restarted ntop and after some time I've checked Summary - Traffic - TCP/UDP Traffic Port Distribution: Last Minute View, but data from that table is not too relevant. I think there is much more about this ntop that I don't know (configuration, usage).

  Read the article

• How to configure/use ntop for measuring upstream traffic made through certain ports

  - by Claudiu

  How to configure ntop so I can get the amount of upload traffic sent through a certain port ? I've added port in ntop/protocol.list, restarted ntop and after some time I've checked Summary - Traffic - TCP/UDP Traffic Port Distribution: Last Minute View, but data from that table is not too relevant. I think there is much more about this ntop that I don't know (configuration, usage).

  Read the article

• domain2.com redirects to domain1.com in Apache

  - by Dmitry Mikhaylov

  I created new virtual host, but when I try to request it, Apache redirects me to another virtual host. What could cause this problem? <VirtualHost XXX.XXX.XXX.XXX:80 > ServerName domain1.com AddDefaultCharset utf-8 CustomLog /var/www/httpd-logs/domain1.com.access.log combined DocumentRoot /home/user/www/domain1.com ErrorLog /var/www/httpd-logs/domain1.com.error.log ServerAdmin [email protected] ServerAlias www.domain1.com SuexecUserGroup user user AddType application/x-httpd-php .php .php3 .php4 .php5 .phtml AddType application/x-httpd-php-source .phps php_admin_value open_basedir "/home/user:." php_admin_value sendmail_path "/usr/sbin/sendmail -t -i -f [email protected]" php_admin_value upload_tmp_dir "/home/user/mod-tmp" php_admin_value session.save_path "/home/user/mod-tmp" ScriptAlias /cgi-bin/ /home/user/www/domain1.com/cgi-bin/ </VirtualHost> <VirtualHost XXX.XXX.XXX.XXX:80 > ServerName domain2.com CustomLog /dev/null combined DocumentRoot /home/user/www/domain2.com ErrorLog /dev/null ServerAdmin [email protected] ServerAlias www.domain2.com SuexecUserGroup user user AddType application/x-httpd-php .php .php3 .php4 .php5 .phtml AddType application/x-httpd-php-source .phps php_admin_value open_basedir "/home/user:." php_admin_value sendmail_path "/usr/sbin/sendmail -t -i -f [email protected]" php_admin_value upload_tmp_dir "/home/user/mod-tmp" php_admin_value session.save_path "/home/user/mod-tmp" </VirtualHost> "apache2ctl -S" output: VirtualHost configuration: XXX.XXX.XXX.XXX:80 is a NameVirtualHost default server domain1.com (/etc/apache2/apache2.conf:266) port 80 namevhost domain1.com (/etc/apache2/apache2.conf:266) port 80 namevhost domain2.com (/etc/apache2/apache2.conf:284) XXX.XXX.XXX.XXX:443 is a NameVirtualHost default server domain1.com (/etc/apache2/apache2.conf:246) port 443 namevhost domain1.com (/etc/apache2/apache2.conf:246) wildcard NameVirtualHosts and _default_ servers: *:443 is a NameVirtualHost default server www.example.com (/etc/apache2/apache2.conf:239) port 443 namevhost www.example.com (/etc/apache2/apache2.conf:239) *:80 is a NameVirtualHost default server domain1.com (/etc/apache2/sites-enabled/000-default:1) port 80 namevhost domain1.com (/etc/apache2/sites-enabled/000-default:1)

  Read the article

• Problem hosting server behing personal router

  - by Venkatesh Hodavdekar

  I recently bought the domain name lucidcontraptions.com and want to host the website from home. I have a D-Link router in which I have set up my personal virtual server correctly. My application server is Apache 2.2. The server works perfectly with the following settings: External IP: 207.172.xx.xx. Public port: 8888 Internal IP: 192.168.xx.xx. Private port: 80 If I go to 207.172.xx.xx:8888/ the server works perfectly and my Apache page shows up without any issues, both from inside the intranet as well as outside. This setting would not work out for me as I am not allowed port numbers in my DNS management. Now when I tweak the settings to the following: External IP: 207.172.xx.xx. Public port: 80 Internal IP: 192.168.xx.xx. Private port: 80 If I go to 207.172.xx.xx/ the server works perfectly and my Apache page shows up without any issues, BUT ONLY FROM INSIDE THE INTRANET. This page does not show up for people outside the intranet.

  Read the article

• Setting multiple Apache2 VirtualHosts with the same DocumentRoot?

  - by sobi3ch

  I'm trying to accomplish something like this DocumentRoot /www/_offline.com <VirtualHost *:80> ServerName example1.com ServerAlias www.example1.com </VirtualHost> <VirtualHost *:80> ServerName example2.com ServerAlias www.example2.com DocumentRoot /www/_offline.com </VirtualHost> Is it possible to have ONE documentRoot for different domains? VirtualHost configuration: wildcard NameVirtualHosts and _default_ servers: *:80 is a NameVirtualHost default server localhost (/etc/apache2/sites-enabled/000-default:1) port 80 namevhost localhost (/etc/apache2/sites-enabled/000-default:1) port 80 namevhost aa.atd (/etc/apache2/sites-enabled/all-phoenix-domains:2) port 80 namevhost atd.atd (/etc/apache2/sites-enabled/all-phoenix-domains:13) port 80 namevhost test (/etc/apache2/sites-enabled/test:1) Syntax OK

  Read the article

• Adobe Coldfusion Railo OpenBD Apache Tomcat Multiple Sites

  - by chris hough

  Here's what I am trying to do, unless I am crazy: I am trying to use Tomcat with the multiple workers, so far I got OpenBD working, but having trouble with Railo, and will be tackling Adobe after. each engine deployed as a war separated by different workers I wanted to keep both the sites and engines inside my sites directory I have to remap the symlink for the WEB-INF when I switch engines = have not found a way around this my thought is to have everything separated into modules and I want to be able to execute both cfm and php code in a single site.  Ideally, it would be amazing if there would be a way to not have to remap the symlink as well. thoughts? can this be done? I am trying to mimic how this would be setup on a live server, not using eclipse for example. here is what I am working with so far: my apache workers.properties worker.list=openbd, openbdadmin, railo, railoadmin  worker.openbd.type=ajp13  worker.openbd.host=local.mydev.openbd  worker.openbd.port=8009 worker.openbdadmin.type=ajp13  worker.openbdadmin.host=local.admin.openbd worker.openbdadmin.port=8009   worker.railo.type=ajp13  worker.railo.host=local.mydev.railo  worker.railo.port=8009 worker.railoadmin.type=ajp13  worker.railoadmin.host=local.admin.railo worker.railoadmin.port=8009   my tomcat servers.xml < Host name="local.admin.openbd" appBase="/Users/[myusername]/Websites/coldfusion.engines"  unpackWARs="false" autoDeploy="true" xmlValidation="true" xmlNamespaceAware="false"        < Context path="" docBase="openbd/" reloadable="true" privileged="true" antiResourceLocking="false" anitJARLocking="false" allowLinking="true" < /Host        < Host name="local.admin.railo"   appBase="/Users/[my username]/Websites/coldfusion.engines" unpackWARs="false" autoDeploy="true" xmlValidation="true" xmlNamespaceAware="false"        < Context path="" docBase="railo/"  reloadable="true" privileged="true" antiResourceLocking="false" anitJARLocking="false" allowLinking="true" < /Host < Host name="local.mydev.openbd"   appBase="/Users/[my username]/Websites/coldfusion.engines" unpackWARs="false" autoDeploy="true" xmlValidation="true" xmlNamespaceAware="false" < Context path="" docBase="/Users/[my username]/Websites/example.mydev/wwwroot/"  reloadable="true" privileged="true" antiResourceLocking="false" anitJARLocking="false" allowLinking="true"< /Context < /Host < Host name="local.mydev.railo"   appBase="/Users/[my username]/Websites/coldfusion.engines"  unpackWARs="false" autoDeploy="true" xmlValidation="true" xmlNamespaceAware="false" < Context path="" docBase="/Users/[my username]/Websites/example.mydev/wwwroot/"  reloadable="true" privileged="true" antiResourceLocking="false" anitJARLocking="false" allowLinking="true" < /Host my apache vhosts ServerName local.admin.openbd DocumentRoot /Users/[my username]/Websites/coldfusion.engines/openBD/ #Mount OpenBD and tell it to only server cfml files JkMount /*.cfm openbdadmin ErrorLog "/Users/[my username]/Websites/apache.logs/local_openbdadmin_error.log" ServerName local.admin.railo DocumentRoot /Users/[my username]/Websites/coldfusion.engines/railo/ #Mount Railo and tell it to only server cfml files JkMount /*.cfm railoadmin ErrorLog "/Users/[my username]/Websites/apache.logs/local_railoadmin_error.log" ServerName local.mydev DocumentRoot /Users/[my username]/Websites/example.mydev/wwwroot ErrorLog "/Users/[my username]/Websites/apache.logs/local_example_mydev_error.log" ServerName local.mydev.openbd DocumentRoot /Users/[my username]/Websites/example.mydev/wwwroot #Mount OpenBD and tell it to only server cfml files JkMount /*.cfm openbd ErrorLog "/Users/[my username]/Websites/apache.logs/local_example_mydev_openbd_error.log" ServerName local.mydev.railo DocumentRoot /Users/[my username]/Websites/example.mydev/wwwroot JkMount /*.cfm railo ErrorLog "/Users/[my username]/Websites/apache.logs/local_example_mydev_railo_error.log" my folder structure I am using websites/apache.logs/ websites/coldfusion.engines/ websites/coldfusion.engines/cfusion/ websites/coldfusion.engines/openBD/ websites/coldfusion.engines/railo/ websites/example.mydev/ websites/example.mydev/wwwroot/ websites/example.mydev/wwwroot/index.cfm   websites/example.mydev/wwwroot/index.htm   websites/example.mydev/wwwroot/index.php   error log output [Thu Aug 27 00:54:50.443 2009] [11279:2686719776] [info] init_jk::mod_jk.c (3183): mod_jk/1.2.28 initialized [Thu Aug 27 00:54:51.346 2009] [11280:2686719776] [info] init_jk::mod_jk.c (3183): mod_jk/1.2.28 initialized [Thu Aug 27 00:55:18.963 2009] [11284:2686719776] [info] jk_open_socket::jk_connect.c (594): connect to 127.0.0.1:8009 failed (errno=61) [Thu Aug 27 00:55:18.963 2009] [11284:2686719776] [info] ajp_connect_to_endpoint::jk_ajp_common.c (922): Failed opening socket to (127.0.0.1:8009) (errno=61) [Thu Aug 27 00:55:18.963 2009] [11284:2686719776] [error] ajp_send_request::jk_ajp_common.c (1507): (openbdadmin) connecting to backend failed. Tomcat is probably not started or is listening on the wrong port (errno=61) [Thu Aug 27 00:55:18.963 2009] [11284:2686719776] [info] ajp_service::jk_ajp_common.c (2447): (openbdadmin) sending request to tomcat failed (recoverable), because of error during request sending (attempt=1) [Thu Aug 27 00:55:19.063 2009] [11284:2686719776] [info] jk_open_socket::jk_connect.c (594): connect to 127.0.0.1:8009 failed (errno=61) [Thu Aug 27 00:55:19.063 2009] [11284:2686719776] [info] ajp_connect_to_endpoint::jk_ajp_common.c (922): Failed opening socket to (127.0.0.1:8009) (errno=61) [Thu Aug 27 00:55:19.063 2009] [11284:2686719776] [error] ajp_send_request::jk_ajp_common.c (1507): (openbdadmin) connecting to backend failed. Tomcat is probably not started or is listening on the wrong port (errno=61) [Thu Aug 27 00:55:19.063 2009] [11284:2686719776] [info] ajp_service::jk_ajp_common.c (2447): (openbdadmin) sending request to tomcat failed (recoverable), because of error during request sending (attempt=2) [Thu Aug 27 00:55:19.063 2009] [11284:2686719776] [error] ajp_service::jk_ajp_common.c (2466): (openbdadmin) connecting to tomcat failed. [Thu Aug 27 00:55:19.063 2009] [11284:2686719776] [info] jk_handler::mod_jk.c (2615): Service error=-3 for worker=openbdadmin [Thu Aug 27 00:55:20.377 2009] [11283:2686719776] [info] jk_open_socket::jk_connect.c (594): connect to 127.0.0.1:8009 failed (errno=61) [Thu Aug 27 00:55:20.377 2009] [11283:2686719776] [info] ajp_connect_to_endpoint::jk_ajp_common.c (922): Failed opening socket to (127.0.0.1:8009) (errno=61) [Thu Aug 27 00:55:20.377 2009] [11283:2686719776] [error] ajp_send_request::jk_ajp_common.c (1507): (railoadmin) connecting to backend failed. Tomcat is probably not started or is listening on the wrong port (errno=61) [Thu Aug 27 00:55:20.377 2009] [11283:2686719776] [info] ajp_service::jk_ajp_common.c (2447): (railoadmin) sending request to tomcat failed (recoverable), because of error during request sending (attempt=1) [Thu Aug 27 00:55:20.477 2009] [11283:2686719776] [info] jk_open_socket::jk_connect.c (594): connect to 127.0.0.1:8009 failed (errno=61) [Thu Aug 27 00:55:20.477 2009] [11283:2686719776] [info] ajp_connect_to_endpoint::jk_ajp_common.c (922): Failed opening socket to (127.0.0.1:8009) (errno=61) [Thu Aug 27 00:55:20.477 2009] [11283:2686719776] [error] ajp_send_request::jk_ajp_common.c (1507): (railoadmin) connecting to backend failed. Tomcat is probably not started or is listening on the wrong port (errno=61) [Thu Aug 27 00:55:20.477 2009] [11283:2686719776] [info] ajp_service::jk_ajp_common.c (2447): (railoadmin) sending request to tomcat failed (recoverable), because of error during request sending (attempt=2) [Thu Aug 27 00:55:20.477 2009] [11283:2686719776] [error] ajp_service::jk_ajp_common.c (2466): (railoadmin) connecting to tomcat failed. [Thu Aug 27 00:55:20.477 2009] [11283:2686719776] [info] jk_handler::mod_jk.c (2615): Service error=-3 for worker=railoadmin

  Read the article

• Transparent proxying in MacOS X 10.6 Snow Leopard (and maybe FreeBSD)

  - by apenwarr

  I'm trying to create a transparent proxy on my MacOS machine in order to port the sshuttle ssh-based transproxy VPN from Linux. I think I almost have it working, but sadly, almost is not 100%. Short version is this. In one window, start something that listens on port 12300: $ while :; do nc -l 12300; done Now enable proxying: # sysctl -w net.inet.ip.forwarding=1 # sysctl -w net.inet.ip.fw.enable=1 # ipfw add 1000 fwd 127.0.0.1,12300 log tcp from any to any And now test it out: $ telnet localhost 9999 # any port number will do # this works; type stuff and you'll see it in the nc window $ telnet google.com 80 # any host/port will do # this *doesn't* work! After the latter experiment, I see lines like this in netstat: $ netstat -tn | grep ^tcp4 tcp4 0 0 66.249.91.104.80 192.168.1.130.61072 SYN_RCVD tcp4 0 0 192.168.1.130.61072 66.249.91.104.80 SYN_SENT The second socket belongs to my telnet program; the first is more suspicious. SYN_RCVD implies that my SYN packet was correctly captured by the firewall and taken in by the kernel, but apparently the SYNACK was never sent back to telnet, because it's still in SYN_SENT. On the other hand, if I kill the nc server, I get this: $ telnet google.com 80 Trying 66.249.81.104... telnet: connect to address 66.249.81.104: Connection refused telnet: Unable to connect to remote host ...which is as expected: my proxy server isn't running, so ipfw redirects my connection to port 12300, which has nobody listening on it, ie. connection refused. My uname says this: $ uname -a Darwin mean.local 10.2.0 Darwin Kernel Version 10.2.0: Tue Nov 3 10:37:10 PST 2009; root:xnu-1486.2.11~1/RELEASE_I386 i386 Does anybody see any different results? (I'm especially interested in Snow Leopard vs Leopard results, as there seem to be some internet rumours that transproxy is broken in Snow Leopard version) Any advice for how to fix?

  Read the article

< Previous Page | 100 101 102 103 104 105 106 107 108 109 110 111  | Next Page >