Search Results

Search found 20668 results on 827 pages for 'last modified'.

Page 105/827 | < Previous Page | 101 102 103 104 105 106 107 108 109 110 111 112  | Next Page >

• dhcp-snooping option 82 drops valid dhcp requests on 2610 series Procurve switches

  - by kce

  We are slowly starting to implement dhcp-snooping on our HP ProCurve 2610 series switches, all running the R.11.72 firmware. I'm seeing some strange behavior where dhcp-request or dhcp-renew packets are dropped when originating from "downstream" switches due "untrusted relay information from client". The full error: Received untrusted relay information from client <mac-address> on port <port-number> In more detail we have a 48 port HP2610 (Switch A) and a 24 port HP2610 (Switch B). Switch B is "downstream" of Switch A by virtue of a DSL connection to one of Switch A ports. The dhcp server is connected to Switch A. The relevant bits are as follows: Switch A dhcp-snooping dhcp-snooping authorized-server 192.168.0.254 dhcp-snooping vlan 1 168 interface 25 name "Server" dhcp-snooping trust exit Switch B dhcp-snooping dhcp-snooping authorized-server 192.168.0.254 dhcp-snooping vlan 1 interface Trk1 dhcp-snooping trust exit The switches are set to trust BOTH the port the authorized dhcp server is attached to and its IP address. This is all well and good for the clients attached to Switch A, but the clients attached to Switch B get denied due to the "untrusted relay information" error. This is odd for a few reasons 1) dhcp-relay is not configured on either switch, 2) the Layer-3 network here is flat, same subnet. DHCP packets should not have a modified option 82 attribute. dhcp-relay does appear to be enabled by default however: SWITCH A# show dhcp-relay DHCP Relay Agent : Enabled Option 82 : Disabled Response validation : Disabled Option 82 handle policy : append Remote ID : mac Client Requests Server Responses Valid Dropped Valid Dropped ---------- ---------- ---------- ---------- 0 0 0 0 SWITCH B# show dhcp-relay DHCP Relay Agent : Enabled Option 82 : Disabled Response validation : Disabled Option 82 handle policy : append Remote ID : mac Client Requests Server Responses Valid Dropped Valid Dropped ---------- ---------- ---------- ---------- 40156 0 0 0 And interestingly enough the dhcp-relay agent seems very busy on Switch B, but why? As far as I can tell there is no reason why dhcp requests need a relay with this topology. And furthermore I can't tell why the upstream switch is dropping legitimate dhcp requests for untrusted relay information when the relay agent in question (on Switch B) isn't modifying the option 82 attributes anyway. Adding the no dhcp-snooping option 82 on Switch A allows the dhcp traffic from Switch B to be approved by Switch A, by virtue of just turning off that feature. What are the repercussions of not validating option 82 modified dhcp traffic? If I disable option 82 on all my "upstream" switches - will they pass dhcp traffic from any downstream switch regardless of that traffic's legitimacy? This behavior is client operating system agnostic. I see it with both Windows and Linux clients. Our DHCP servers are either Windows Server 2003 or Windows Server 2008 R2 machines. I see this behavior regardless of the DHCP servers' operating system. Can anyone shed some light on what's happening here and give me some recommendations on how I should proceed with configuring the option 82 setting? I feel like i just haven't completely grokked dhcp-relaying and option 82 attributes.

  Read the article

• How to enable boot timeout in Grub2?

  - by Casey

  I'm am trying to enable the boot timeout selection in grub2 on Ubuntu 9.10. I modified /etc/default/grub: GRUB_DEFAULT=0 #GRUB_HIDDEN_TIMEOUT=0 GRUB_HIDDEN_TIMEOUT_QUIET=false GRUB_TIMEOUT=2 GRUB_DISTRIBUTOR=`lsb_release -i -s 2> /dev/null || echo Debian` GRUB_CMDLINE_LINUX_DEFAULT="splash quiet" GRUB_CMDLINE_LINUX="" and ran update-grub, but I still do not have a boot timeout counter. What else can you do to enable this?

  Read the article

• proftpd on debian - authuserfile

  - by dirknibleck

  I have installed proftpd on my debian 4.0 server. I have modified the proftpd.conf file so that there is a statement for AuthUserFile, which points to a valid file. The file is configured per the proftpd specs, however the user that I have placed in this file is not able to log-in to the server. What could I be doing wrong? AuthUserFile is of the format: username:passwd:999:1002:www:/var/www:/bin/bash

  Read the article

• Modify styles in OneNote 2010 beta

  - by jay

  I'm running the OneNote 2010 beta and wondering if there is a way to edit the default styles? If you change the default font, the styles wont be changed. Is there any template, registry key or file that allows for the styles to modified?

  Read the article

• Task Scheduler Disable Google Updater Error

  - by muntoo

  Whenever I try to disable GoogleUpdateTaskUser in Vista using Task Scheduler, I get the following: --------------------------- Task Scheduler --------------------------- Not enough quota is available to process this command.GoogleUpdateTaskMachineUA --------------------------- OK --------------------------- After clicking OK: --------------------------- Task Scheduler --------------------------- This task could not be modified as requested. --------------------------- OK --------------------------- I tried this with all the "GoogleUpdate" stuff you can see in the picture below. Any ideas? THIS confirms it should work.

  Read the article

• MySQL Table does not support optimize

  - by Dscoduc

  My Wordpress tables appear to be in need of optimization so I looked into the commmand OPTIMIZE TABLE . When I run the command I get the following results: Table does not support optimize, doing recreate + analyze instead The tables are built using the Wordpress 2.91 installer and haven't been modified at all. Is this normal? How can I optimize my database to keep things working correctly?

  Read the article

• httpd dead but subsys locked

  - by McShark

  Hello, I modified today max_execution_time in php.ini, when I restarted the server, I get this error : Stopping httpd: [FAILED] Starting httpd: (98)Address already in use: make_sock: could not bind to address [::]:80 (98)Address already in use: make_sock: could not bind to address 0.0.0.0:80 no listening sockets available, shutting down Unable to open logs I killed httpd proc : killall httpd, and started it fine, but the I can't open any web site on the server. service httpd status OUTPUT : httpd dead but subsys locked I removed httpd file from /var/lock/subsys/ :S Same problem. Please Help!

  Read the article

• What's the fastest filesystem for developer builds?

  - by Dan Fabulich

  I'm putting together a Linux box that will act as a continuous integration build server; we'll mostly build Java stuff, but I think this question applies to any compiled language. What filesystem and configuration settings should I use? (For example, I know I won't need atime for this!) The build server will spend a lot of time reading and writing small files, and scanning directories to see which files have been modified.

  Read the article

• Why my VPN doesn't work anymore?

  - by xx77aBs

  I have openvpn server running on debian lenny. There is only one client - and it is running Windows 7 64-bit. This has worked for few months without any problems. And now, let's say for the last 7 days, it doesn't work at all. I connect successfully from client to the server, but I can't access anything through VPN. I have set it up so that all internet traffic is routed through VPN, and now when I connect with the client, the client can't do anything on the net (open any webpage, ping google, anything ...). Can you help me to figure out what's wrong ? I don't know where to start. I've also tried to connect to another openvpn server (I've installed and configured openvpn on another server, and when I try to connect to it result is the same). So I think there's something wrong with client ... Here is my connection log: Wed Apr 04 21:35:59 2012 OpenVPN 2.3-alpha1 Win32-MSVC++ [SSL (OpenSSL)] [LZO2] [PF_INET6] [IPv6 payload 20110522-1 (2.2.0)] built on Feb 21 2012 Enter Management Password: Wed Apr 04 21:35:59 2012 MANAGEMENT: TCP Socket listening on [AF_INET]127.0.0.10:25340 Wed Apr 04 21:35:59 2012 Need hold release from management interface, waiting... Wed Apr 04 21:36:00 2012 MANAGEMENT: Client connected from [AF_INET]127.0.0.10:25340 Wed Apr 04 21:36:00 2012 MANAGEMENT: CMD 'state on' Wed Apr 04 21:36:00 2012 MANAGEMENT: CMD 'log all on' Wed Apr 04 21:36:00 2012 MANAGEMENT: CMD 'hold off' Wed Apr 04 21:36:00 2012 MANAGEMENT: CMD 'hold release' Wed Apr 04 21:36:00 2012 WARNING: No server certificate verification method has been enabled. See http://openvpn.net/howto.html#mitm for more info. Wed Apr 04 21:36:00 2012 NOTE: OpenVPN 2.1 requires '--script-security 2' or higher to call user-defined scripts or executables Wed Apr 04 21:36:00 2012 Socket Buffers: R=[8192->8192] S=[8192->8192] Wed Apr 04 21:36:00 2012 MANAGEMENT: >STATE:1333568160,RESOLVE,,, Wed Apr 04 21:36:00 2012 UDPv4 link local: [undef] Wed Apr 04 21:36:00 2012 UDPv4 link remote: [AF_INET]11.22.33.44:1234 Wed Apr 04 21:36:00 2012 MANAGEMENT: >STATE:1333568160,WAIT,,, Wed Apr 04 21:36:00 2012 MANAGEMENT: >STATE:1333568160,AUTH,,, Wed Apr 04 21:36:00 2012 TLS: Initial packet from [AF_INET]11.22.33.44:1234, sid=ee329574 f15e9e04 Wed Apr 04 21:36:00 2012 VERIFY OK: depth=1, C=US, ST=CA, L=SanFrancisco, O=Fort-Funston, CN=Fort-Funston CA, [email protected] Wed Apr 04 21:36:00 2012 VERIFY OK: depth=0, C=US, ST=CA, L=SanFrancisco, O=Fort-Funston, CN=server_key, [email protected] Wed Apr 04 21:36:01 2012 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Wed Apr 04 21:36:01 2012 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Wed Apr 04 21:36:01 2012 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Wed Apr 04 21:36:01 2012 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Wed Apr 04 21:36:01 2012 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Wed Apr 04 21:36:01 2012 [server_key] Peer Connection Initiated with [AF_INET]11.22.33.44:1234 Wed Apr 04 21:36:02 2012 MANAGEMENT: >STATE:1333568162,GET_CONFIG,,, Wed Apr 04 21:36:03 2012 SENT CONTROL [server_key]: 'PUSH_REQUEST' (status=1) Wed Apr 04 21:36:03 2012 PUSH: Received control message: 'PUSH_REPLY,redirect-gateway def1,route 172.16.100.1,topology net30,ping 10,ping-restart 120,ifconfig 172.16.100.6 172.16.100.5' Wed Apr 04 21:36:03 2012 OPTIONS IMPORT: timers and/or timeouts modified Wed Apr 04 21:36:03 2012 OPTIONS IMPORT: --ifconfig/up options modified Wed Apr 04 21:36:03 2012 OPTIONS IMPORT: route options modified Wed Apr 04 21:36:03 2012 ROUTE_GATEWAY 192.168.1.1/255.255.255.0 I=15 HWADDR=00:1f:1f:3f:61:55 Wed Apr 04 21:36:03 2012 do_ifconfig, tt->ipv6=0, tt->did_ifconfig_ipv6_setup=0 Wed Apr 04 21:36:03 2012 MANAGEMENT: >STATE:1333568163,ASSIGN_IP,,172.16.100.6, Wed Apr 04 21:36:03 2012 open_tun, tt->ipv6=0 Wed Apr 04 21:36:03 2012 TAP-WIN32 device [VPN] opened: \\.\Global\{E28FD52B-F6C3-4094-A36A-30CB02FAC7E8}.tap Wed Apr 04 21:36:03 2012 TAP-Win32 Driver Version 9.9 Wed Apr 04 21:36:03 2012 Notified TAP-Win32 driver to set a DHCP IP/netmask of 172.16.100.6/255.255.255.252 on interface {E28FD52B-F6C3-4094-A36A-30CB02FAC7E8} [DHCP-serv: 172.16.100.5, lease-time: 31536000] Wed Apr 04 21:36:03 2012 Successful ARP Flush on interface [31] {E28FD52B-F6C3-4094-A36A-30CB02FAC7E8} Wed Apr 04 21:36:08 2012 TEST ROUTES: 2/2 succeeded len=1 ret=1 a=0 u/d=up Wed Apr 04 21:36:08 2012 C:\Windows\system32\route.exe ADD 11.22.33.44 MASK 255.255.255.255 192.168.1.1 Wed Apr 04 21:36:08 2012 ROUTE: CreateIpForwardEntry succeeded with dwForwardMetric1=25 and dwForwardType=4 Wed Apr 04 21:36:08 2012 Route addition via IPAPI succeeded [adaptive] Wed Apr 04 21:36:08 2012 C:\Windows\system32\route.exe ADD 0.0.0.0 MASK 128.0.0.0 172.16.100.5 Wed Apr 04 21:36:08 2012 ROUTE: CreateIpForwardEntry succeeded with dwForwardMetric1=30 and dwForwardType=4 Wed Apr 04 21:36:08 2012 Route addition via IPAPI succeeded [adaptive] Wed Apr 04 21:36:08 2012 C:\Windows\system32\route.exe ADD 128.0.0.0 MASK 128.0.0.0 172.16.100.5 Wed Apr 04 21:36:08 2012 ROUTE: CreateIpForwardEntry succeeded with dwForwardMetric1=30 and dwForwardType=4 Wed Apr 04 21:36:08 2012 Route addition via IPAPI succeeded [adaptive] Wed Apr 04 21:36:08 2012 MANAGEMENT: >STATE:1333568168,ADD_ROUTES,,, Wed Apr 04 21:36:08 2012 C:\Windows\system32\route.exe ADD 172.16.100.1 MASK 255.255.255.255 172.16.100.5 Wed Apr 04 21:36:08 2012 ROUTE: CreateIpForwardEntry succeeded with dwForwardMetric1=30 and dwForwardType=4 Wed Apr 04 21:36:08 2012 Route addition via IPAPI succeeded [adaptive] Wed Apr 04 21:36:08 2012 Initialization Sequence Completed Wed Apr 04 21:36:08 2012 MANAGEMENT: >STATE:1333568168,CONNECTED,SUCCESS,172.16.100.6,11.22.33.44 Client's route table after connection with OpenVPN: IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.41 281 0.0.0.0 128.0.0.0 172.16.100.1 172.16.100.6 31 94.23.53.45 255.255.255.255 192.168.1.1 192.168.1.41 25 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 128.0.0.0 128.0.0.0 172.16.100.1 172.16.100.6 31 172.16.100.4 255.255.255.252 On-link 172.16.100.6 286 172.16.100.6 255.255.255.255 On-link 172.16.100.6 286 172.16.100.7 255.255.255.255 On-link 172.16.100.6 286 192.168.1.0 255.255.255.0 On-link 192.168.1.41 281 192.168.1.41 255.255.255.255 On-link 192.168.1.41 281 192.168.1.255 255.255.255.255 On-link 192.168.1.41 281 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.41 281 224.0.0.0 240.0.0.0 On-link 172.16.100.6 286 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.41 281 255.255.255.255 255.255.255.255 On-link 172.16.100.6 286 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 192.168.1.1 Default =========================================================================== IPv6 Route Table =========================================================================== Active Routes: If Metric Network Destination Gateway 13 58 ::/0 On-link 1 306 ::1/128 On-link 13 58 2001::/32 On-link 13 306 2001:0:5ef5:79fd:3cc3:6b9:ac7c:14db/128 On-link 15 281 fe80::/64 On-link 31 286 fe80::/64 On-link 13 306 fe80::/64 On-link 13 306 fe80::3cc3:6b9:ac7c:14db/128 On-link 31 286 fe80::7d72:9515:7213:35e3/128 On-link 15 281 fe80::9cec:ce3f:89de:a123/128 On-link 1 306 ff00::/8 On-link 13 306 ff00::/8 On-link 15 281 ff00::/8 On-link 31 286 ff00::/8 On-link =========================================================================== Persistent Routes: None

  Read the article

• Apache apachectl/httpd hangs

  - by VANJ

  Oracle HTTP Server (OHS), RHEL 5.3, Dell hardware Oracle has a modified version of Apache2 for use with web-enabled components in its product suite. The apachectl start command just hangs, even configtest hangs! Not sure what it is waiting for. How does one go about troubleshooting this? Thanks

  Read the article

• Changed Folder Redirection on Server 2008 R2, I didn't see anything change.

  - by Robert Hurst

  I need some help guys. I've just modified the Folder Redirection Policy on my server at work so the hiarcy resembles windows 7's user folder structure rather than XP. I did this to the book so I know its right. However, I'm still seeing that all the user accounts are still layed out as XP compatible folder hiracys. Is there somthing I need to do to update these accounts with the new policy?

  Read the article

• Clever way to automatically compress unused files on a Linux USB stick?

  - by Luke Stanley

  Surely there is a way to compress files that aren't frequently modified, to ensure low overheads in file access? Any recommendations? Note: I do not yet have noatime set, maybe file access data could be used, at least at first?

  Read the article

• Debian + ProFTPD + LDAP Incorrect Password Issue

  - by Tristan Hall

  I have the LDAP configuration configured for ProFTPD and I have modified the modules.conf file to include the LDAP module. However, every time I login with FileZilla I get 530 Login Incorrect. It does this for all users except those whose passwords are defined locally as well as in LDAP. The exact same setup works fine on my CentOS server and I've already tried re-installing it after purging the configuration files.

  Read the article

• Odd squid transparent redirect behavior

  - by EMiller

  This is the first time I've set up squid. It's running a redirect script that does some text search/replace on html pages, and then saves them to a location on the same machine on the nginx path - then issues the redirect to that URL (it's an art project :D). The relevant lines in squid.conf are http_port 3128 transparent redirect_program /etc/squid/jefferson_redirect.py The jefferson_redirect.py script is based on this script: http://gofedora.com/how-to-write-custom-redirector-rewritor-plugin-squid-python/ The issue: I'm getting strange http redirect behavior. For example, here is the normal request/response from a PHP script that issues a header("Location:"); - a 302 redirect: http://redirector.mysite.com/?unicmd=g+yreka GET /?unicmd=g+yreka HTTP/1.1 Host: redirector.mysite.com User-Agent: Mozilla/5.0 (X11; U; Linux x86_64; en-US; rv:1.9.1.9) Gecko/20100330 Fedora/3.5.9-1.fc12 Firefox/3.5.9 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-us,en;q=0.5 Accept-Encoding: gzip,deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive: 300 Connection: keep-alive HTTP/1.1 302 Found Date: Tue, 13 Apr 2010 05:15:43 GMT Server: Apache X-Powered-By: PHP/5.2.11 Location: http://www.google.com/search?q=yreka Content-Type: text/html Vary: User-Agent,Accept-Encoding Content-Encoding: gzip Content-Length: 2108 Keep-Alive: timeout=3, max=100 Connection: Keep-Alive Here's what it looks like when running through the squid proxy (note that "redirector.mysite.com" is not the site running squid or nginx): http://redirector.mysite.com/?unicmd=g+yreka GET /?unicmd=g+yreka HTTP/1.1 Host: redirector.mysite.com User-Agent: Mozilla/5.0 (X11; U; Linux x86_64; en-US; rv:1.9.1.9) Gecko/20100330 Fedora/3.5.9-1.fc12 Firefox/3.5.9 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-us,en;q=0.5 Accept-Encoding: gzip,deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive: 300 Proxy-Connection: keep-alive If-Modified-Since: Tue, 13 Apr 2010 05:21:02 GMT HTTP/1.0 200 OK Server: nginx/0.7.62 Date: Tue, 13 Apr 2010 05:21:10 GMT Content-Type: text/html Content-Length: 17865 Last-Modified: Tue, 13 Apr 2010 05:21:10 GMT Accept-Ranges: bytes X-Cache: MISS from jefferson X-Cache-Lookup: HIT from jefferson:3128 Via: 1.1 jefferson:3128 (squid/2.7.STABLE6) Connection: keep-alive Proxy-Connection: keep-alive It is basically working - but the URL http://redirector.mysite.com/?unicmd=g+yreka remains unchanged, while displaying the google page (mostly broken as it's using URLs relative to redirector.mysite.com) I've experienced a similar thing with google results pages: when clicking to another page from google, I get a google URL, with the other site's content. Sorry for the long post - many thanks if you've read this far! Any ideas?

  Read the article

• Squid appears to be running storeurl_rewrite_program, but not using the result.

  - by Justin Love

  I've built a storeurl_rewrite_program (which strips some changing query-strings), and verified from logging in the script that it is being run and generating the desired modified url. However, access.log continues to show TCP_MISS and store.log has SWAPOUT with the unmodified url. Why would Squid run the rewriter and then throw away the result?

  Read the article

• With modern PC systems, what less-than-optimal designs have we inherited?

  - by Rob Kam

  What have been less than optimal design choices, that are now (almost) immutable features of the modern PC system, and what constraints led to these choices? There have been a great many of these. For example the qwerty keyboard is widespread although the Dvorak keyboard might be a better choice. I guess this is something to do with the teletypes that were used as early computer keyboards, which had originally been modified from typewriters.

  Read the article

• How does NFS read cache work on Debian?

  - by Ztyx

  I am planning to use NFS to serve out many small files. They will be read very often so client side caching is crucial. Does NFS handle this? Is there a way to increase the client side caching in some way? ...or should I look at another solution? Syncing using rsync or unison periodically is not an option since the files are modified on the client side from time to time.

  Read the article

• What is the date column in Windows 7 explorer - it seems lacking any relevance

  - by Notitze

  I can't get myself to understand what is the default date column in Windows 7 Explorer. It's not the creation date really and it's not the modified date ... What is it? Anyone knows what Microsoft had in mind with this other than trying to confuse its users? There must be some thought to it in terms of its relevance and usability. Can anyone shed some light on this? Thanks

  Read the article

• Strange behavior when changing default shell, and setting explorer.exe as winlogon shell for specific user

  - by Ophir Yoktan

  I use a custom logon shell on a machine (windows 7) for security reasons - which works fine by altering HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon\shell. However, I also want that the administrator will still be able to manage the machine, so I modified the user specific key: HKEY_CURRENT_USER\Software\Microsoft\Windows NT\CurrentVersion\Winlogon\shell back to explorer.exe - but when I log on I get a single windows explorer window, and not the full desktop. does any one know how to configure the normal desktop shell only to a specific user?

  Read the article

• When .VHD get updated?

  - by Recce2jp

  Hello, I have a VM with a .vhd file however, when I connet to the VM (by RDP) and make some changes (create a directory and add a small file with notepad) the .VHD file stays unchanged. The 'Date modified' of the .VHD stays at the starttime of the VM. 1/How can we force an update of het VM while the VM is running? 2/Where aree the temporary changes kept? Hypervisor: Microsoft Hyper-V server 2008R2 (free download version) regards, Maxim

  Read the article

• ubuntu gnome short cut keys

  - by benjipete

  Hi, I have done something quite silly and not sure how to fix it. I modified some of the gnome keyboard short cuts and was trying to disable the "Run Application" command. In the process I assigned it to the delete key and every time I hit delete the "Run Application" window comes up. It would not normally be a problem but the "Keyboard Shortcuts" no long has the short cut in the window so I can't disable it. Any help advice would be appreciated. Cheers Ben

  Read the article

• Spoof Mac Address from ip command.

  - by GuyNoir

  I'm trying to spoof my Mac Address on a modified version of linux (Android). The main problem is that because it has been stripped down, the ifconfig command has been stripped out, and I only can use the 'ip' busybox command. I've been trying to use ip link set address xx:xx:xx:xx:xx:xx dev tiwlan0 but I get the error, ip: socket: Operation not permitted Any help?

  Read the article

• File auditing software for Windows Server 2003

  - by David Collantes

  I am looking for a program or program suite that will allow the auditing of network shared resources (specifically storage space), and render reports (who created, deleted, moved, modified files, etc). Yes, I know I can turn on auditing on Windows, but the Event Log isn't quite the "charmer" for the job.

  Read the article

• GUI to Change the Login Screen Wallpaper Image on Snow Leopard

  - by lexu

  the "standard" login screen background on OSC (Leopard and Snow Leopard) can be modified using these command line incantations: cd /System/Library/CoreServices sudo mv DefaultDesktop.jpg DefaultDesktop_org.jpg sudo cp /path/of/image.jpg DefaultDesktop.jpg I learned that here QUESTION: is there a GUI based utility for people like my wife and daughter? .. they DO want to customize (worse: they want me to do it ), but they DON'T want to learn the terminal ( since I know how). They DO know how to enter an admin's credentials when prompted.

  Read the article

• pg_restore is taking too long to finish. What could be the problem?

  - by Randell

  pg_restore is taking too long to finish. I already performed the following service postgresql initdb /etc/init.d/postgresql start Modified /var/lib/pgsql/data/pg_hba.conf to use local all all trust host all all 127.0.0.1/32 ident sameuser host all all ::1/128 ident sameuser /etc/init.d/postgresql restart What could be the problem?

  Read the article

< Previous Page | 101 102 103 104 105 106 107 108 109 110 111 112  | Next Page >