Search Results

Search found 2778 results on 112 pages for 'ping fm'.

Page 105/112 | < Previous Page | 101 102 103 104 105 106 107 108 109 110 111 112  | Next Page >

• Win-XP Browsers Hang on page load - (waiting for...)

  - by CHarmon

  Hello, I’m having problems with my browsers hanging on loading pages on my desktop machine. I’m using Windows XP Pro with SP3 and fully updated except for IE 8. All three of my browsers, IE 7, Chrome and Firefox are having the same problems. Pages are not being loaded and are hanging on “waiting for …”. The browsers are waiting for the page being loaded or ad servers. Sometimes a page will load but the loading graphic continues to be displayed as if the page were still loading when the page appears to be fully loaded. The problem is bad enough that I can’t really use any of my browsers. I can eventually get most pages to load by stopping and restarting the page load. I have DSL modem with a wireless router and I have been able to eliminate the modem and router from being the source of my problem. My laptop doesn’t have any problems even when hardwired to the router and with the wireless connection disabled. I deleted the NIC and let XP re-install. Also tried a different network cable. Tried the same router port used in the laptop test. One clue that may be important is that I can’t connect to my router using the desktop machine…the page hangs while trying to connect. I can ping the router and I can quickly connect to the router using the laptop. I also can’t use the Windows update process – the page never fully loads. The problem affects other user accounts and even happens in safe mode. I am convinced the problem is with part of the O/S…some layer able to affect all of the browsers. The purpose of this post is to see if anyone has some ideas before I do a XP repair. I have done quite a bit of trouble-shooting: Ran a full anti-virus scan with AVG – no problems. Ran full scans with Spybot, MalwareBytes and Sophos anti-rootkit – no problems. Ran Chkdsk with both options checked. Ran Disk Clean up Defragged RE-installed IE7 Cleared all the browser caches Ran Ccleaner (registry tool) Ran HijackThis – nothing unusual (problem happens in safe mode too) Ran Process Explorer – no unusual processes Used System Restore and fell back several days – no change in the problem Booted to last known good configuration – no change in the problem Ran MicrosoftFixit50199.msi – no change in the problem Any ideas or suggestions would be appreciated…I’m not looking forward to doing a repair on XP. Thanks in advance for any help.

  Read the article

• Windows 2008 R2 IPsec encryption in tunnel mode, hosts in same subnet

  - by fission

  In Windows there appear to be two ways to set up IPsec: The IP Security Policy Management MMC snap-in (part of secpol.msc, introduced in Windows 2000). The Windows Firewall with Advanced Security MMC snap-in (wf.msc, introduced in Windows 2008/Vista). My question concerns #2 – I already figured out what I need to know for #1. (But I want to use the ‘new’ snap-in for its improved encryption capabilities.) I have two Windows Server 2008 R2 computers in the same domain (domain members), on the same subnet: server2 172.16.11.20 server3 172.16.11.30 My goal is to encrypt all communication between these two machines using IPsec in tunnel mode, so that the protocol stack is: IP ESP IP …etc. First, on each computer, I created a Connection Security Rule: Endpoint 1: (local IP address), eg 172.16.11.20 for server2 Endpoint 2: (remote IP address), eg 172.16.11.30 Protocol: Any Authentication: Require inbound and outbound, Computer (Kerberos V5) IPsec tunnel: Exempt IPsec protected connections Local tunnel endpoint: Any Remote tunnel endpoint: (remote IP address), eg 172.16.11.30 At this point, I can ping each machine, and Wireshark shows me the protocol stack; however, nothing is encrypted (which is expected at this point). I know that it's unencrypted because Wireshark can decode it (using the setting Attempt to detect/decode NULL encrypted ESP payloads) and the Monitor Security Associations Quick Mode display shows ESP Encryption: None. Then on each server, I created Inbound and Outbound Rules: Protocol: Any Local IP addresses: (local IP address), eg 172.16.11.20 Remote IP addresses: (remote IP address), eg 172.16.11.30 Action: Allow the connection if it is secure Require the connections to be encrypted The problem: Though I create the Inbound and Outbound Rules on each server to enable encryption, the data is still going over the wire (wrapped in ESP) with NULL encryption. (You can see this in Wireshark.) When the arrives at the receiving end, it's rejected (presumably because it's unencrypted). [And, disabling the Inbound rule on the receiving end causes it to lock up and/or bluescreen – fun!] The Windows Firewall log says, eg: 2014-05-30 22:26:28 DROP ICMP 172.16.11.20 172.16.11.30 - - 60 - - - - 8 0 - RECEIVE I've tried varying a few things: In the Rules, setting the local IP address to Any Toggling the Exempt IPsec protected connections setting Disabling rules (eg disabling one or both sets of Inbound or Outbound rules) Changing the protocol (eg to just TCP) But realistically there aren't that many knobs to turn. Does anyone have any ideas? Has anyone tried to set up tunnel mode between two hosts using Windows Firewall? I've successfully got it set up in transport mode (ie no tunnel) using exactly the same set of rules, so I'm a bit surprised that it didn't Just Work™ with the tunnel added.

  Read the article

• Out of nowhere, ssh_exchange_identification: Connection closed by remote hot me too

  - by dgerman

  See similar: Out of nowhere, ssh_exchange_identification: Connection closed by remote host Today, 6/19/12 attempting to ssh to the same host as usual ssh replied ssh_exchange_identification: Connection closed by remote host two additional attempts failed ssh -v $RWS OpenSSH_5.6p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Reading configuration data /etc/ssh_config debug1: Applying options for * debug1: Connecting to Real-World-Systems.com [174.127.119.33] port 22. debug1: Connection established. debug1: identity file /Users/dgerman/.ssh/id_rsa type 1 debug1: identity file /Users/dgerman/.ssh/id_rsa-cert type -1 debug1: identity file /Users/dgerman/.ssh/id_dsa type -1 debug1: identity file /Users/dgerman/.ssh/id_dsa-cert type -1 ssh_exchange_identification: Connection closed by remote host ping host was successful, ftp host was successful, ssh now successful, ssh -v $RWS OpenSSH_5.6p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Reading configuration data /etc/ssh_config debug1: Applying options for * debug1: Connecting to Real-World-Systems.com [174.127.119.33] port 22. debug1: Connection established. debug1: identity file /Users/dgerman/.ssh/id_rsa type 1 debug1: identity file /Users/dgerman/.ssh/id_rsa-cert type -1 debug1: identity file /Users/dgerman/.ssh/id_dsa type -1 debug1: identity file /Users/dgerman/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_4.3 debug1: match: OpenSSH_4.3 pat OpenSSH_4* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.6 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host 'real-world-systems.com' is known and matches the RSA host key. debug1: Found key in /Users/dgerman/.ssh/known_hosts:5 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,gssapi-with-mic,password debug1: Next authentication method: publickey debug1: Offering RSA public key: /Users/dgerman/.ssh/id_rsa debug1: Authentications that can continue: publickey,gssapi-with-mic,password debug1: Trying private key: /Users/dgerman/.ssh/id_dsa debug1: Next authentication method: password ++++ What gives?? +++++++++++ Mac OS X 10.4.7 , OpenSSH_5.6p1, OpenSSL 0.9.8r 8 Feb 2011, /Users/dgerman/.ssh > ls -la total 24 drwx------ 7 dgerman staff 238 Jun 19 15:46 . drwxr-xr-x 389 dgerman staff 13226 Jun 19 15:46 .. -rw------- 1 dgerman staff 1766 Feb 26 18:25 id_rsa -rw-r--r-- 1 dgerman staff 400 Feb 26 18:25 id_rsa.pub -rw-r--r-- 1 dgerman staff 67 Feb 26 18:27 keyfingerprint -rw-r--r-- 1 dgerman staff 6215 May 1 08:11 known_hosts -rw-r--r-- 1 dgerman staff 220 Feb 26 18:26 randomart

  Read the article

• Joining Windows 7 Professional to a Windows Server 2003 R2 x64 domain fails.

  - by Vinko Vrsalovic

  I have a windows 7 professional (spanish) laptop trying to join a Windows Server 2003 (english) domain. It detect correctly the SRV record, finding the proper domain controller, but then the join fails with the error message (snippet, because the error is in spanish) An Active Directory Domain Controller for This Domain Could Not be Contacted The DNS is correctly set, and client can ping by name and IP the server, the server can ping the client by IP. I've tested with the FW down to no avail. A host of other XP Pro clients are connected to the domain. I've restarted Net Logon and checked that Windows Time is up. Also the times are in sync between the server and the client. I'll put below diagnostics output. I'm wondering if there's anything special to be done on either the server or the client to have a Win 7 Pro join a 2k3 R2 domain. The following diagnostic information follows: netdiag /q for the DC dcdiag on the DC ipconfig /all on the Win 7 client netdiag /q on the DC: .................................. Computer Name: HI-X2 DNS Host Name: hi-x2.hi.local System info : Microsoft Windows Server 2003 R2 (Build 3790) Processor : EM64T Family 6 Model 23 Stepping 10, GenuineIntel List of installed hotfixes : KB923561 KB924667-v2 KB925398_WMP64 KB925902 KB926122 KB927891 KB929123 KB930178 KB932168 KB936357 KB938127 KB941569 KB942830 KB942831 KB943055 KB943460 KB944338-v2 KB944653 KB945553 KB946026 KB948496 KB950760 KB950762 KB950974 KB951066 KB951748 KB952004 KB952069 KB952954 KB954155 KB954550-v7 KB955069 KB955759 KB956572 KB956802 KB956803 KB956844 KB958469 KB958644 KB958869 KB959426 KB960225 KB960803 KB960859 KB961063 KB961118 KB961501 KB967715 KB967723 KB968389 KB968816 KB969059 KB969947 KB970238 KB970430 KB970483 KB971032 KB971468 KB971657 KB971737 KB971961 KB971961-IE8 KB972270 KB973037 KB973354 KB973507 KB973540 KB973687 KB973815 KB973825 KB973869 KB973904 KB973917-v2 KB974112 KB974318 KB974392 KB974571 KB975025 KB975467 KB975560 KB975713 KB976662-IE8 KB977290 KB977816 KB977914 KB978037 KB978262 KB978338 KB978542 KB978601 KB978706 KB979306 KB979309 KB979683 KB980182 KB980182-IE8 KB980232 KB980302-IE8 KB981332-IE8 KB981350 Q147222 Per interface results: Adapter : Local Area Connection Host Name. . . . . . . . . : hi-x2.hi.local IP Address . . . . . . . . : 10.0.1.199 Subnet Mask. . . . . . . . : 255.0.0.0 Default Gateway. . . . . . : 10.0.1.1 Dns Servers. . . . . . . . : 10.0.1.199 WINS service test. . . . . : Skipped Global results: [WARNING] You don't have a single interface with the 'WorkStation Service', 'Messenger Service', 'WINS' names defined. DNS test . . . . . . . . . . . . . : Passed PASS - All the DNS entries for DC are registered on DNS server '10.0.1.199'. IP Security test . . . . . . . . . : Skipped The command completed successfully dcdiag on the DC: Domain Controller Diagnosis Performing initial setup: Done gathering initial info. Doing initial required tests Testing server: Default-First-Site-Name\HI-X2 Starting test: Connectivity ......................... HI-X2 passed test Connectivity Doing primary tests Testing server: Default-First-Site-Name\HI-X2 Starting test: Replications ......................... HI-X2 passed test Replications Starting test: NCSecDesc ......................... HI-X2 passed test NCSecDesc Starting test: NetLogons ......................... HI-X2 passed test NetLogons Starting test: Advertising ......................... HI-X2 passed test Advertising Starting test: KnowsOfRoleHolders ......................... HI-X2 passed test KnowsOfRoleHolders Starting test: RidManager ......................... HI-X2 passed test RidManager Starting test: MachineAccount ......................... HI-X2 passed test MachineAccount Starting test: Services ......................... HI-X2 passed test Services Starting test: ObjectsReplicated ......................... HI-X2 passed test ObjectsReplicated Starting test: frssysvol ......................... HI-X2 passed test frssysvol Starting test: frsevent ......................... HI-X2 passed test frsevent Starting test: kccevent ......................... HI-X2 passed test kccevent Starting test: systemlog ......................... HI-X2 passed test systemlog Starting test: VerifyReferences ......................... HI-X2 passed test VerifyReferences Running partition tests on : ForestDnsZones Starting test: CrossRefValidation ......................... ForestDnsZones passed test CrossRefValidation Starting test: CheckSDRefDom ......................... ForestDnsZones passed test CheckSDRefDom Running partition tests on : DomainDnsZones Starting test: CrossRefValidation ......................... DomainDnsZones passed test CrossRefValidation Starting test: CheckSDRefDom ......................... DomainDnsZones passed test CheckSDRefDom Running partition tests on : Schema Starting test: CrossRefValidation ......................... Schema passed test CrossRefValidation Starting test: CheckSDRefDom ......................... Schema passed test CheckSDRefDom Running partition tests on : Configuration Starting test: CrossRefValidation ......................... Configuration passed test CrossRefValidation Starting test: CheckSDRefDom ......................... Configuration passed test CheckSDRefDom Running partition tests on : hi Starting test: CrossRefValidation ......................... hi passed test CrossRefValidation Starting test: CheckSDRefDom ......................... hi passed test CheckSDRefDom Running enterprise tests on : hi.local Starting test: Intersite ......................... hi.local passed test Intersite Starting test: FsmoCheck ......................... hi.local passed test FsmoCheck ipconfig /all on the Windows 7 client: Configuraci¢n IP de Windows Nombre de host. . . . . . . . . : hi-p6 Sufijo DNS principal . . . . . : Tipo de nodo. . . . . . . . . . : h¡brido Enrutamiento IP habilitado. . . : no Proxy WINS habilitado . . . . . : no Adaptador de LAN inal mbrica Conexi¢n de red inal mbrica: Sufijo DNS espec¡fico para la conexi¢n. . : Descripci¢n . . . . . . . . . . . . . . . : Intel(R) WiFi Link 5100 AGN Direcci¢n f¡sica. . . . . . . . . . . . . : 00-22-FB-63-47-A0 DHCP habilitado . . . . . . . . . . . . . : no Configuraci¢n autom tica habilitada . . . : s¡ Direcci¢n IPv4. . . . . . . . . . . . . . : 10.0.1.42(Preferido) M scara de subred . . . . . . . . . . . . : 255.255.255.0 Puerta de enlace predeterminada . . . . . : 10.0.1.1 Servidores DNS. . . . . . . . . . . . . . : 10.0.1.199 NetBIOS sobre TCP/IP. . . . . . . . . . . : habilitado Adaptador de Ethernet Conexi¢n de  rea local: Estado de los medios. . . . . . . . . . . : medios desconectados Sufijo DNS espec¡fico para la conexi¢n. . : Descripci¢n . . . . . . . . . . . . . . . : Realtek PCIe GBE Family Controller Direcci¢n f¡sica. . . . . . . . . . . . . : 00-1E-33-1F-35-B1 DHCP habilitado . . . . . . . . . . . . . : s¡ Configuraci¢n autom tica habilitada . . . : s¡ Adaptador de t£nel isatap.{8926581E-09AC-4123-906B-DA6386AD2D60}: Estado de los medios. . . . . . . . . . . : medios desconectados Sufijo DNS espec¡fico para la conexi¢n. . : Descripci¢n . . . . . . . . . . . . . . . : Adaptador ISATAP de Microsoft Direcci¢n f¡sica. . . . . . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP habilitado . . . . . . . . . . . . . : no Configuraci¢n autom tica habilitada . . . : s¡ Adaptador de t£nel Teredo Tunneling Pseudo-Interface: Sufijo DNS espec¡fico para la conexi¢n. . : Descripci¢n . . . . . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface Direcci¢n f¡sica. . . . . . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP habilitado . . . . . . . . . . . . . : no Configuraci¢n autom tica habilitada . . . : s¡ Direcci¢n IPv6 . . . . . . . . . . : 2001:0:5ef5:73ba:1cec:3883:f5ff:fed5(Preferido) V¡nculo: direcci¢n IPv6 local. . . : fe80::1cec:3883:f5ff:fed5%13(Preferido) Puerta de enlace predeterminada . . . . . : :: NetBIOS sobre TCP/IP. . . . . . . . . . . : deshabilitado

  Read the article

• Random Computer Crashes

  - by Josh W.

  Ok, here's a wierd one for you all. Occasionally my PC here at work will crash in a very peculiar way. My dual monitors will suddenly go blank as if there is no longer a video signal, the USB mouse light will go dark and mouse stays unresponsive, the keyboard lights will not change status when the appropriate keys are pressed (Num/Caps/Scoll Lock). The CD Tray WILL open and close. But the computer will not respond to a ping request. For all intents & purposes it's as if the computer is off, except it wasn't intentional by me. The power light and internal fans are still on and I've now lost any unsaved work. Now here's where it gets wierd. This PC is part of a batch of PC's we got from a local vendor who does our initial system builds. Mine, and 6 other co-workers PCs all have the same issue. Originally we thought it was a bad combination of hardware, but through trial and error the only thing we haven't eliminated are the OS, Mobo & CPU. The problem was so bad for some of them that they ended up going back to their 5 year old dinosaurs in order to get some work done, for me the problem isn't as bad, maybe once every other day or so, but still enough to bite me in the ass if I've forgotten my ritualistic pressing of CTRL-S every 1-5 minutes. In this case we've tried two different video cards, two different power supplies, two different memory configurations, running on a UPS/not on UPS, updating/rolling back video drivers, three different bios revisions. The only things we haven't swapped are the mobo & cpu, mainly because a new mobo means a new Hardware Abstraction Layer, ie re-install of windows and there's alot of other software on this PC that takes forever to reload by hand. There was a base image that our systems team created with all the drivers installed and the basic setup of software our company uses, but they then must customize the setup for us programmers so it takes a while to get a new configuration up and going. I'm a programmer by day and am usually pretty good at diagnosing computer problems whether through trial and error or not. We've pretty much exhausted all the ideas we can think of here, short of a new mobo/cpu. Was hoping someone out there might have anything else we can try.. Relevant Parts: OS: XP Pro 32-bit Motherboard: Intel DG41RQ CPU: Intel Core-2 Quad Q9400 @ 2.66GHz Current BIOS Version/Date Intel Corp. RQG4110H.86A.0014.2010.0306.1151, 3/6/2010 Dual LCD's, Viewsonic VG930m & Samsung SyncMaster 910v (other people have different models, but listed in case there's some very wierd problem with the signals being sent/received) PS/2 Keyboard USB Microsoft Intellimouse BIOS Versions Tried: R 0013 12/23/2009 R 0014 3/6/2010 Video cards Tried GeForce 8400 GS Radeon HD 4350 - ASUS EAH4350 Two Different Power Supplies a 380W & 550W Ram Configurations 2GB - 1 x 2GB 4GB - 2 x 2GB

  Read the article

• New Exchange 2010 CAS cannot find domain controllers

  - by NorbyTheGeek

  I am experiencing problems migrating from Exchange 2003 to Exchange 2010. I am on the first step: installing a new 2010 Client Access Server role. The Active Directory domain functional level is 2003. All domain controllers are 2003 R2. The only existing Exchange 2003 server happens to be housed on one of the domain controllers. It is running Exchange 2003 Standard w/ SP2. IPv6 is enabled and working on all domain controllers, servers, and routers, including this new Exchange server. After installing the CAS role on a new 2008 R2 server (Hyper-V VM) I am receiving 2114 Events: Process MSEXCHANGEADTOPOLOGYSERVICE.EXE (PID=1600). Topology discovery failed, error 0x80040a02 (DSC_E_NO_SUITABLE_CDC). Look up the Lightweight Directory Access Protocol (LDAP) error code specified in the event description. To do this, use Microsoft Knowledge Base article 218185, "Microsoft LDAP Error Codes." Use the information in that article to learn more about the cause and resolution to this error. Use the Ping or PathPing command-line tools to test network connectivity to local domain controllers. Prior to each, I receive the following 2080 Event: Process MSEXCHANGEADTOPOLOGYSERVICE.EXE (PID=1600). Exchange Active Directory Provider has discovered the following servers with the following characteristics: (Server name | Roles | Enabled | Reachability | Synchronized | GC capable | PDC | SACL right | Critical Data | Netlogon | OS Version) In-site: b.company.intranet CDG 1 0 0 1 0 0 0 0 0 s.company.intranet CDG 1 0 0 1 0 0 0 0 0 Out-of-site: a.company.intranet CD- 1 0 0 0 0 0 0 0 0 o.company.intranet CD- 1 0 0 0 0 0 0 0 0 g.company.intranet CD- 1 0 0 0 0 0 0 0 0 Connectivity between the new Exchange server and all domain controllers via IPv4 and IPv6 are all working. I have verified that the new Exchange server is a member of the following groups: Exchange Servers Exchange Domain Servers Exchange Install Domain Servers Exchange Trusted Subsystem Heck, I even put the new Exchange server into Domain Admins just to see if it would help. It didn't. I can't find any evidence of Active Directory replication problems, all pre-setup Setup tasks (/PrepareLegacyExchangePermissions, /PrepareSchema, /PrepareAD, /PrepareDomain) completed successfully. The only problem so far that I haven't been able to resolve with my Active Directory is I am unable to get my IPv6 subnets into Sites and Services Where should I proceed from here?

  Read the article

• Nagios core Event Handler not working

  - by sivashanmugam

  Nagios Event Handler is not triggering when the service is taking more time to response or down. My configuration in below nagios.cfg enable_event_handlers=1 localhost.cfg define service { use generic-service host_name Server service_description test-server servicegroups test-service check_command check-service is_volatile 0 check_period 24x7 max_check_attempts 4 normal_check_interval 2 retry_check_interval 2 contact_groups testcontacts notification_period 24x7 notification_options w,u,c,r notifications_enabled 1 event_handler_enabled 1 event_handler recheck-service } command.cfg define command{ command_name recheck-service command_line /usr/local/nagios/libexec/alert.sh $SERVICESTATE$ $SERVICESTATETYPE$ $SERVICEATTEMPT$ } alert.sh file !/bin/sh set -x case "$1" in OK) # The service just came back up, so don't do anything... ;; WARNING) # We don't really care about warning states, since the service is probably still running... ;; UNKNOWN) # We don't know what might be causing an unknown error, so don't do anything... ;; CRITICAL) Aha! The HTTP service appears to have a problem - perhaps we should restart the server... Is this a "soft" or a "hard" state? case "$2" in We're in a "soft" state, meaning that Nagios is in the middle of retrying the check before it turns into a "hard" state and contacts get notified... SOFT) # What check attempt are we on? We don't want to restart the web server on the first check, because it may just be a fluke! case "$3" in Wait until the check has been tried 3 times before restarting the web server. If the check fails on the 4th time (after we restart the web server), the state type will turn to "hard" and contacts will be notified of the problem. Hopefully this will restart the web server successfully, so the 4th check will result in a "soft" recovery. If that happens no one gets notified because we fixed the problem! 3) echo -n "Going To Ping the Virtual Machine (3rd soft critical state)..." # Call the init script to restart the HTTPD server myresult=`/usr/local/nagios/libexec/check_http xyz.com -t 100 | grep 'time'| awk '{print $10}'` echo "Your Service Is taking the following time Delay" "$myresult Seconds" |mail -s "WARNING : Service Taken More Time To Response" [email protected] ;; esac ;; # The HTTP service somehow managed to turn into a hard error without getting fixed. # It should have been restarted by the code above, but for some reason it didn't. # Let's give it one last try, shall we? # Note: Contacts have already been notified of a problem with the service at this

  Read the article

• Switch flooding when bonding interfaces in Linux

  - by John Philips

  +--------+ | Host A | +----+---+ | eth0 (AA:AA:AA:AA:AA:AA) | | +----+-----+ | Switch 1 | (layer2/3) +----+-----+ | +----+-----+ | Switch 2 | +----+-----+ | +----------+----------+ +-------------------------+ Switch 3 +-------------------------+ | +----+-----------+----+ | | | | | | | | | | eth0 (B0:B0:B0:B0:B0:B0) | | eth4 (B4:B4:B4:B4:B4:B4) | | +----+-----------+----+ | | | Host B | | | +----+-----------+----+ | | eth1 (B1:B1:B1:B1:B1:B1) | | eth5 (B5:B5:B5:B5:B5:B5) | | | | | | | | | +------------------------------+ +------------------------------+ Topology overview Host A has a single NIC. Host B has four NICs which are bonded using the balance-alb mode. Both hosts run RHEL 6.0, and both are on the same IPv4 subnet. Traffic analysis Host A is sending data to Host B using some SQL database application. Traffic from Host A to Host B: The source int/MAC is eth0/AA:AA:AA:AA:AA:AA, the destination int/MAC is eth5/B5:B5:B5:B5:B5:B5. Traffic from Host B to Host A: The source int/MAC is eth0/B0:B0:B0:B0:B0:B0, the destination int/MAC is eth0/AA:AA:AA:AA:AA:AA. Once the TCP connection has been established, Host B sends no further frames out eth5. The MAC address of eth5 expires from the bridge tables of both Switch 1 & Switch 2. Switch 1 continues to receive frames from Host A which are destined for B5:B5:B5:B5:B5:B5. Because Switch 1 and Switch 2 no longer have bridge table entries for B5:B5:B5:B5:B5:B5, they flood the frames out all ports on the same VLAN (except for the one it came in on, of course). Reproduce If you ping Host B from a workstation which is connected to either Switch 1 or 2, B5:B5:B5:B5:B5:B5 re-enters the bridge tables and the flooding stops. After five minutes (the default bridge table timeout), flooding resumes. Question It is clear that on Host B, frames arrive on eth5 and exit out eth0. This seems ok as that's what the Linux bonding algorithm is designed to do - balance incoming and outgoing traffic. But since the switch stops receiving frames with the source MAC of eth5, it gets timed out of the bridge table, resulting in flooding. Is this normal? Why aren't any more frames originating from eth5? Is it because there is simply no other traffic going on (the only connection is a single large data transfer from Host A)? I've researched this for a long time and haven't found an answer. Documentation states that no switch changes are necessary when using mode 6 of the Linux interface bonding (balance-alb). Is this behavior occurring because Host B doesn't send any further packets out of eth5, whereas in normal circumstances it's expected that it would? One solution is to setup a cron job which pings Host B to keep the bridge table entries from timing out, but that seems like a dirty hack.

  Read the article

• OpenVPN multiple servers on the same subnet, high availability

  - by andre

  Hey everyone. Let me start by saying that my Linux experience isn't super awesome but I can usually find my way around things easily. Over at work we have an OpenVPN setup that's been due for some improvement for a while now. The main server (tap mode) runs in our office, behind a rather slow DSL connection. The main problem is that, since I'm usually out of the office, every time I want to access something on the virtual network I have to go through that server to get anywhere else. We have two servers up on 100 Mbit connections that we use for development and production purposes, about 3 more servers in the office (one of them behind a different T1 line for VOIP) and about two dozen clients who use the network on a daily basis from various locations. We've had situations where network routing (outside of our control) would not allow people to reach our main OpenVPN server whilst the other locations were connectable. Also any time someone outside the office wants to fetch something from any of the servers (say, a 500 MB code repository), a whopping 20 KB/s download speed is just unacceptable these days (did I mention slow DSL? ok). We had to implement traffic shaping on this server since maxing out this connection was fairly trivial. I had the thought of running two (or more) OpenVPN servers in the network. These would have to have the same subnet though, as our application relies on virtual network's IP addresses for some of its core functionality. The clients would also preferably retain the same IP addresses but that's not vital. For simplicity, lets call the current server office and the second server I'm setting up, cloud. Call the server on the T1 phone. This proved to be rather complex because as soon as I connect to cloud, I cannot see office. Any routes to a server that would go through office also do not work while I'm connected to cloud (no ping, nothing) and vice-versa. There's no rules for iptables that would be blocking the traffic either. Recently I came across this article on linuxjournal but the solution they provide seems to only cover the use of two servers and somewhat outdated (can't even find much documentation, their wiki is offline). They also state that adding more servers would be a complex task. Ideally I would like to keep the existing server office running the virtual network and also run the OpenVPN daemon on the cloud and phone servers (100 Mbit and very reliable connection, respectively) so that we're on safe ground in case of a hardware failure, DSL failure, etc. So, in essence, I'm looking for a highly available OpenVPN solution (fix, patch, hack, tweak, whatever you want to call it) that will accept connections on multiple hosts (2 or more) whilst keeping the same IP address subnet regardless of the server to which you connect to. Thanks for reading and sorry for the long post, I hope it gets the point across :P

  Read the article

• Windows Server 2008 - one MAC Address, assign multiple external IP's to VirtualBoxes running as guests on host

  - by Sise

  Couldn't find any help @ google or here. The scenario: Windows Server 2008 Std x64 on i7-975, 12 GB RAM. The server is running in a data centre. One hardware NIC - RealTek PCIe GBE - one MAC Address. The data centre provides us 4 static external IP's. The first is assigned to the host by default of course. I have ordered all 4 IP's, the data centre can assign the available IP's to the physical MAC address of the given NIC only. This means one NIC, one MAC Address, 4 IP's. Everything works fine so far. Now, what I would like to have: Installed VirtualBox with 1-3 guests running, each gets it's own external IP assigned. Each of it should be an standalone Win Server 2008. It looks like the easiest way would be to put the guests into an virtual subnet and routing all data coming to the 2nd till 4th external IP through to this guests using there subnet IP's. I have been through the VirtualBox User Manuel regarding networking. What's not working: I can't use bridged networking without anything else, because the IP's are assigned to the one MAC address only. I can't use NAT networking because it does not allow access from outside or the host to the guest. I do not wanna use port forwarding. Host-only networking itself would not allow internet access, by sharing the default internet connection of the host, internet is granted from the guest to the outside but not from outside or the host to the guest. InternalNetworking is not really an option here. What I have tried is to create an additional MS Loopback adapter for a routed subnet, where the Vbox guests are in, now the idea was to NAT the internet connection to the loopback 'subnet'. But I can't ping the gateway from the guests. By using route command in the command shell or RRAS (static route, NAT) I didn't get there as well. Solutions like the following do work for the one way, but not for the way back: For your situation, it might be best to use the Host-Only adapter for ICS. Go to the preferences of VB itself and select network. There you can change the configuration for the interface. Set the IP address to 192.168.0.1, netmask 255.255.255.0. Disable the DHCP server if it isn't already and that's it. Now the Guest should get an IP from Windows itself and be able to get onto the internet, while you can also access the Host. Slowly I'm pretty stucked with this topic. There is a possibility I've just overlooked something or just didn't getting it by trying, especially using RRAS, but it's kinda hard to find useful howto's or something in the web. Thanks in advance! Best regards, Simon

  Read the article

• Routing table with two NIC adapters in libvirt/KVM

  - by lzap

  I created a virtual NAT network (192.168.100.0/24 network) in my libvirt and new guest with two interfaces - one in this network, one as bridged (10.34.1.0/24 network) to the local LAN. The reason for that is I need to have my own virtual network for my DHCP/TFTP/DNS testing and still want to access my guest externally from my LAN. On both networks I have working DHCP, both giving them IP addresses. When I setup NAT port forwarding (e.g. for ssh), I can connect to the eth0 (virtual network), everything is fine. But when I try to access the eth1 via bridged interface, I have no response. I guess I have problem with my routing table - outgoing packets are routed to the virtual NAT network (which has access to the machine I am connecting from - I can ping it). But I am not sure if this setup is correct. I think I need to add something to my routing table. # ifconfig eth0 Link encap:Ethernet HWaddr 52:54:00:B4:A7:5F inet addr:192.168.100.14 Bcast:192.168.100.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:feb4:a75f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:16468 errors:0 dropped:27 overruns:0 frame:0 TX packets:6081 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:22066140 (21.0 MiB) TX bytes:483249 (471.9 KiB) Interrupt:11 Base address:0x2000 eth1 Link encap:Ethernet HWaddr 52:54:00:DE:16:21 inet addr:10.34.1.111 Bcast:10.34.1.255 Mask:255.255.255.0 inet6 addr: fe80::5054:ff:fede:1621/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:34 errors:0 dropped:0 overruns:0 frame:0 TX packets:189 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4911 (4.7 KiB) TX bytes:9 # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.100.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.34.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 1002 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 1003 0 0 eth1 0.0.0.0 192.168.100.1 0.0.0.0 UG 0 0 0 eth0 Network I am trying to connect from is different than network the hypervisor is connected to: 10.36.0.0. But it is accessible from that network. So I tried to add new route rule: route add -net 10.36.0.0 netmask 255.255.0.0 dev eth1 And it is not working. I thought setting correct interface would be sufficient. What is needed to get my packets coming through?

  Read the article

• Is there a switch that will connect directly to my modem and allow my router to serve only as a WiFi connection?

  - by Abner

  Details . . Devices . Internets -50Mbps Cable Internet Modem - Motorola Surfboard Extreme Router - Netgear WNDR3700v3 Switch - D-Link DGS-1008G Wired Ethernet Cable - Cat6_24Awg_ Device Configuration - Modem\Router\Switch . . Internet Usage . Wired Demand XBOX 360 1 Gaming PC 2 PC - HD video . WiFi Demand 3 android + 1 Laptop for browsing and group video chat simultaneously . . Specifics . I am experiencing problems with network speeds and reliability on both wired and wireless connections. On many occasions I experience WiFi Speeds that vary between the 15mbps to 0.50 mbs (or less) and ping ranging from 15ms to 500ms. These results are from when I notice problems with internet lag and run speedtest.net to get details of problems. I have a stretched out floor-plan and old building materials drastically affecting my cellphone signal strength as well). After Reading the "Known Issues" Section on the webpage below http://www.dd-wrt.com/wiki/index.php/Netgear_WNDR3700#Known_Issues I bought the switch and Cat6 cable to increase speed and relieve stress on router in an attempt to fix the symptoms. I thought I'd use the router in a Modem\Switch\Router configuration. I thought I'd only have to use the router for mobile WiFi connections like android or Laptops when necessary (hopefully eliminating the problem caused by the router when subjected to all those demanding Ethernet connections) When I started unboxing the switch, I noticed the manual of this DGS-1008G shows it being connected in the Modem\Router\Switch order and not in the Modem\Switch\Router configuration I was aiming for. I have not been able to find a solid plan to remedy my specific problem without buying another expensive router. I would like to get the speeds I am paying for without buying another router. (My WiFi Adapters would also need to be updated if new router is required, meaning more $$$). I can always sell the switch and get a better one that will bypass the router because my most demanding internet connections are Wired. . . Questions Can I accomplish a Modem\Switch\Router configuration with current switch? Is there a different way to get the wired speed I need while providing WiFi only when necessary? . .

  Read the article

• How to configure DD-WRT routing table when creating an isolated network segment for PCI C VT compliance

  - by tetranz

  I'm the volunteer support and system admin person at a small private school. We need to setup a PCI compliant Windows PC as a virtual terminal for credit card processing. I've read questionnaire SAQ C-VT and, to quote, this computer needs to be accessed: "via a computer that is isolated in a single location, and is not connected to other locations or systems within your environment (this can be achieved via a firewall or network segmentation to isolate the computer from other systems)" Our setup is as follows: DSL modem from ISP is setup to be a "transparent pipe" with no extra services. That goes into the WAN port of Linksys WRT54-GL running a DD-WRT. The LAN is 192.168.1.x. There are a couple of other WRT54-GL / DD-WRT devices. One is used as a wireless AP and another is a client bridge. To isolate the VT (virtual terminal) machine, I have another DD-WRT device. Its WAN is connected to a port on the 192.168.1.x LAN. The virtual terminal machine is connected to its LAN which is at 192.168.10.x. The SPI Firewall etc is turned on. It's basically the default DD-WRT gateway setup where the "ISP" is our own LAN. That's working. All incoming traffic to the VT machine is blocked, including from our own LAN. The VT can access the internet BUT, and here's the problem, it can also ping any of the computers on the 192.168.1.x LAN. I think I need to stop that. I'm guessing that I could do something with the Static Routing table in the VT machine's DD-WRT device. I need to route anything going to 192.168.1.x other than the gateway which is 192.168.1.1 to 0.0.0.0 or something like that. That's where I'm stuck at the end of my knowledge. Or ... do I need to get yet another DD-WRT so the network is "balanced". Maybe I need to have the internet from the DSL going into a DD-WRT which has only two devices on its LAN i.e., two other DD-WRTs, one for the main LAN and one for the VT. I think that would do but I'd like to avoid the extra cost and complexity if I don't need it. Thanks

  Read the article

• weird SSH connection timed out

  - by bran

  This problem started when I tried to login to my brand spaning new VPS server. I remember that in my first SSH try on the server I actually got prompt for password several times which would mean that there is no port blocking problem from my isp. Since the password did'nt work for me (for some reason). I had a lot of authentication failure. After that attempting to log in to the server just timed out. I did the same at mediatemple (which used to work before with sftp) and put in wrong password and now trying to ssh (or even SFTP) gives me timeout error. So some kind of security feature is preventing me from trying too many times to log in, either from my side or from the server side. Any idea what it could be? TRaceroute and ping works on the ips. I am using a zyxel wimax modem (max-206m1r - if that's relevent) c:\Program Files (x86)\OpenSSH\bin>ssh.exe [email protected] ssh: connect to host 109.169.7.136 port 22: Connection timed out c:\Program Files (x86)\OpenSSH\bin>ssh.exe [email protected] ssh: connect to host 109.169.7.131 port 22: Connection timed out c:\Program Files (x86)\OpenSSH\bin>ssh.exe [email protected] ssh: connect to host 87.117.249.227 port 22: Connection timed out c:\Program Files (x86)\OpenSSH\bin>ssh.exe [email protected] -vv OpenSSH_5.6p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Reading configuration data /etc/ssh_config debug2: ssh_connect: needpriv 0 debug1: Connecting to 87.117.249.227 [87.117.249.227] port 22. debug1: connect to address 87.117.249.227 port 22: Connection timed out ssh: connect to host 87.117.249.227 port 22: Connection timed out c:\Program Files (x86)\OpenSSH\bin>ssh.exe s122797.gridserver.com Could not create directory '/home/pavs/.ssh'. The authenticity of host 's122797.gridserver.com (205.186.175.110)' can't be est ablished. RSA key fingerprint is 33:24:1e:38:bc:fd:75:02:81:d8:39:42:16:f6:f6:ff. Are you sure you want to continue connecting (yes/no)? yes Failed to add the host to the list of known hosts (/home/pavs/.ssh/known_hosts). Password: Password: Password: [email protected]'s password: Permission denied, please try again. [email protected]'s password: Permission denied, please try again. [email protected]'s password: Received disconnect from 205.186.175.110: 2: Too many authentication failures fo r pavs c:\Program Files (x86)\OpenSSH\bin>ssh.exe s122797.gridserver.com ssh: connect to host s122797.gridserver.com port 22: Connection timed out c:\Program Files (x86)\OpenSSH\bin>ssh.exe s122797.gridserver.com ssh: connect to host s122797.gridserver.com port 22: Connection timed out

  Read the article

• Looking for a new, free firewall (Sunbelt has a huge hole)

  - by Jason

  I've been using Sunbelt Personal Firewall v. 4.5 (previously Kerio). I've discovered that blocking Firefox connections in the configuration doesn't stop EXISTING Firefox connections. (See my post here yesterday http://superuser.com/questions/132625/sunbelt-firewall-4-5-wont-block-firefox) The "stop all traffic" may work on existing connections - but I'm done testing, as I need to be able to be selective, at any time. I was using the free version, so the "web filtering" option quit working after some time (mostly blocking ads and popups), but I didn't use that anyway. I used the last free version of Kerio before finally having to go to Sunbelt, because Kerio had an unfixed bug where you'd eventually get the BSOD and have to reset Kerio's configuration and start over (configure everything again). So I'm looking for a new Firewall. I don't like ZoneAlarm at all (no offense to all it's users that may be here - personal taste). I need the following: (Sunbelt has all these, except *) - 1. Be able to block in/out to localhost (trusted)/internet selectively for each application with a click (so there's 4 click boxes for each application) [*that effects everything immediately, regardless of what's already connected]. When a new application attempts a connection, you get an allow/deny/remember windows. - 2. Be able to easily set up filter rules for 'individual application'/'all applications,' by protocol, port/address (range), local, remote, in, out. [*Adding a filter rule also doesn't block existing connections in Sunbelt. That needs to work too.] - 3. Have an easy-to-get-to way to "stop all traffic" (like a right click option on the running icon in the task bar). - 4. Be able to set trusted/internet in/out block/allowed (4 things per item) for each of IGMP, ping, DNS, DHCP, VPN, and broadcasts. - 5. Define locahost as trusted/untrusted, define adapter connections as trusted/untrusted. - 6. Block incoming connetions during boot-up and shutdown. - 7. Show existing connections, including local & remote ip/port, protocol, current speed, total bytes transferred, and local ports opened for Listening. - 8. An Intrusion Prevention System which blocks (optionally select each one) known intrustions (long list). - 9. Block/allow applications from starting other applications (deny/allow/remember window). Wish list: A way of knowing what svchost.exe is doing - who is actually using it/calling it. I allowed it for localhost, and selectively allowed it for internet each time the allow/deny window came up. Thanks for any help/suggestions. (I'm using Windows XP SP3.)

  Read the article

• First time installing Linux/Apache - uanble to connect

  - by bob

  I's my first time installing Linux/Apache. I loaded CentOS and LAMPP on a machine attached to a LAN. Turned off http and mysql (because I didn't want conflict with LLAMPP) chkconfig httpd off chkconfig mysqld off then successfully LAMPP started with /opt/lampp/lampp start Starting XAMPP for Linux 1.7.3a... XAMPP: Starting Apache with SSL (and PHP5)... XAMPP: Starting MySQL... XAMPP: Starting ProFTPD... XAMPP for Linux started. Problem: Unable to connect - Firefox can't establish a connection to the server at 179.16.51.36. I need some pointers as to where to look next. No errors in error_log file (just some warnings) I can ping server. httpd.conf looks like this: ServerRoot "/opt/lampp" Listen 80 ServerAdmin [email protected] ServerName 179.16.51.36 DocumentRoot "/opt/lampp/htdocs" <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory "/opt/lampp/htdocs"> Options Indexes FollowSymLinks ExecCGI Includes Order allow,deny Allow from all </Directory> ErrorLog logs/error_log LogLevel warn <IfModule log_config_module> LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %b" common <IfModule logio_module> LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\" %I %O" combinedio </IfModule> CustomLog logs/access_log common </IfModule> <IfModule alias_module> ScriptAlias /cgi-bin/ "/opt/lampp/cgi-bin/" </IfModule> <IfModule cgid_module> </IfModule> <Directory "/opt/lampp/cgi-bin"> AllowOverride None Options None Order allow,deny Allow from all </Directory> DefaultType text/plain <IfModule mime_module> TypesConfig etc/mime.types AddType application/x-compress .Z AddType application/x-gzip .gz .tgz AddHandler cgi-script .cgi .pl AddType text/html .shtml AddOutputFilter INCLUDES .shtml </IfModule> EnableMMAP off EnableSendfile off

  Read the article

• Trying to get DNS services running on Windows Server 2008 R2, what am I getting wrong ?

  - by LaserBeak

  Ok, So I am basically trying to get a home server pc up that will provide Domain name services, act as Mail server and web server. I have one static IP, well it's not officially static but hasn't changed in two years so I'll call it static. I have done the following: Configured router NAT/virtual port forward UDP/TCP port 53 to the internal IP of my server 192.168.1.16, in adapter settings specified the manual settings: 192.168.1.16 IP, gateway 192.168.1.1, Subnet: 255.255.255.0 and loopback DNS: 127.0.0.1 Using my public my public IP Checked using http://www.canyouseeme.org/ that port 53 is open and is not being blocked by my ISP. It can see services on this port. Registered Domain name (mydomain.com.au) Updated whois database through the domain registrars site and registered NameServer names: ns0.mydomain.com.au and ns2.mydomain.com.au, both have been associated with my single public IP. (Waited 24 hours) Update the nameserver for mydomain.com.au: primary ns0.mydomain.com.au secondary: ns2.mydomain.com.au (waited 24+ hours) Installed Server 2008 R2, install web server role and DNS role. Webserver works when I enter my public IP into browser of any PC/mobile, get IIS7 welcome page. In DNS server: Created new forward lookup zone: ; ; Database file mydoman.com.au.dns for mydomain.com.au zone. ; Zone version: 10 ; @ IN SOA mydomain.com.au. mydomain.testdomain.com. ( 10 ; serial number 900 ; refresh 600 ; retry 86400 ; expire 3600 ) ; default TTL ; ; Zone NS records ; @ NS ns0.mydomain.com.au. @ NS ns1.mydomain.com.au. ; ; Zone records ; @ A 192.168.1.16 www A 192.168.1.16 The Domain name services will however not work, the whois database updated with ns0.mydomain.com.au etc. but when I type in my site name www.mydomain.com.au from an external machine it will not open site and I can't even ping it (Can't find host) When I check the ns0.mydomain.com.au NS record using a tool Like: http://www.squish.net/dnscheck/ I get: Security: Server ns0.mydomain.com.au (XXX.XXX.XXX.XX <- my public IP) is recursive Domain exists but there is no such record Any ideas, thanks...

  Read the article

• Windows doesn't get access to internet though linux easily does

  - by flashnik

  We have a very interesting problem. The network is configured in this way: internet is connected to Trendnet switch TS DHCP server at 192.168.0.1 running on Ubuntu (S) is connected to internet switch DNS is also configured on 192.168.0.1 on S D-Link Wi-Fi boosters are connected to switch TS PCs use D-Link PCI-E Wi-Fi cards to get access to network PCs have both Ubuntu and Windows 7 There are about 40 PCs. When PC is booted to Ubuntu it easily gets access to internet. But when it's booted to Windows 7, it gets a valid IP-address, but doesn't get access to internet. The address, mask, DNS, GW-address are totally the same as when it's booted under Ubuntu. The S is reacheble and pingable. Sometimes when we are lucky the PC gets access to Internet, but after rebooting it can lose it. When PC under Windows has access, it has totally the same settings as when it doesn't. What can be done? UPDATE I shared a dropbox with 2 captures of traffic. Ping.pcap is a capture of pinging 8.8.8.8. And google-browser.pcap is a capture of opening a google.com in a browser, both of them are in tcpdump formats and made by Wireshark on Win PC. The MAC of Win PC ends on b7:63 and IP is 192.168.0.130. UPDATE2 This is ifconfig output from Ubuntu Server eth0 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8d inet addr:193.200.211.74 Bcast:193.200.211.78 Mask:255.255.255.0 inet6 addr: fe80::21e:67ff:fe13:d58d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:196284 errors:0 dropped:44 overruns:0 frame:0 TX packets:190682 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:158032255 (158.0 MB) TX bytes:156441225 (156.4 MB) Interrupt:19 Memory:c1400000-c1420000 eth0:2 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8d inet addr:192.168.0.1 Bcast:192.168.0.254 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Memory:c1400000-c1420000 eth1 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8c UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 Memory:c1300000-c1320000 nslookup from Win results in DNS request timeout, nbtstat in 'not found'.

  Read the article

• Ubuntu 11.10 firewall/gateway - no client internet access

  - by Siriss

  I have read many other posts but cannot figure this out. eth0 is my external connected to a Comcast modem. The server has internet access with no issues. eth1 is internal and running DHCP for the clients. I have DHCP working just fine, all my clients can get an IP and ping the server but they cannot access the internet. I am using ISC-DHCP-SERVER and have set /etc/default/isc-dhcp-server to INTERFACE="eht1" Here is my dhcpd.conf file located in /etc/dhcp/dhcpd.conf ddns-update-style interim; ignore client-updates; subnet 10.0.10.0 netmask 255.255.255.0 { range 10.0.10.10 10.0.10.200; option routers 10.0.10.2; option subnet-mask 255.255.255.0; option domain-name-servers 208.67.222.222, 208.67.220.220; #OpenDNS # option domain-name "example.com"; default-lease-time 21600; max-lease-time 43200; authoritative; } I have made the *net.ipv4.ip_forward=1* change in /etc/sysctl.conf here is my interfaces file: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp iface eth1 inet static address 10.0.10.2 netmask 255.255.255.0 network 10.0.10.0 auto eth1 And finally- here is my iptables.conf file: # Firewall configuration written by system-config-firewall # Manual customization of this file is not recommended. *nat :PREROUTING ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] -A POSTROUTING -s 10.0.10.0/24 -o eth0 -j MASQUERADE #-A PREROUTING -i eth0 -p tcp --dport 59668 -j DNAT --to-destination 10.0.10.2:59668 COMMIT *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -i eth1 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 22 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 80 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 443 -j ACCEPT -A INPUT -m state --state NEW -m tcp -p tcp --dport 53 -j ACCEPT -A INPUT -m state --state NEW -m udp -p udp --dport 53 -j ACCEPT -A FORWARD -s 10.0.10.0/24 -o eth0 -j ACCEPT -A FORWARD -d 10.0.10.0/24 -m state --state ESTABLISHED,RELATED -i eth0 -j ACCEPT -A FORWARD -p icmp -j ACCEPT -A FORWARD -i lo -j ACCEPT -A FORWARD -i eth1 -j ACCEPT #-A FORWARD -i eth0 -m state --state NEW -m tcp -p tcp -d 10.0.10.2 --dport 59668 -j ACCEPT -A INPUT -j REJECT --reject-with icmp-host-prohibited -A FORWARD -j REJECT --reject-with icmp-host-prohibited COMMIT I am completely stuck. I cannot figure out why the clients cannot access the internet. Am I missing a service? Is a service not running? Any help would be greatly appreciated. I tried to be as thorough as possible but please let me know if I have missed something. Thank you!

  Read the article

• All internet requests in Windows time out

  - by Brandon

  So, I've run into a very strange problem with my home wireless network. Previously, at seemingly random times, the router seemed to disconnect all wireless hosts and cause all of the wired hosts to have a "limited connection" according to windows. In order to fix this, I had to unplug all of the wired hosts from the router, unplug the modem from the router, and power cycle the router. This seemed to solve the problem for a while until the exact same thing happened a day later and I had to go through the same process again. That's where I noticed something weird happening. There was one wireless host (a Windows Vista laptop) that seemed to be causing the router to disconnect the other hosts whenever it connected. When this happened, only that laptop was able to use the wireless from the router. When this happened, I disconnected it from the wireless (by disabling the wireless adapter) then reconnected it (by re-enabling it) and now it, like the other hosts, couldn't connect. I've never really seen anything this strange happen on our network before. So, I restored the router to factory settings and the problem seems to have vanished except one crucial problem. There's another host (a Windows 7 laptop) that was perfectly able to connect before all of the router issues and even in between the crashing and power-cycling events but now says its connected and says it's able to reach the Internet, but all requests time out. In any browser I've tried, the tab says connecting to [site]... for a solid minute and then tells me the request timed out. When I try to ping google.com in cmd it also says request timed out. In frustration, I booted into a dual-boot Ubuntu installation on the Windows 7 host and the connection works fine, to my surprise, as ubuntu is where I am now typing this rather long question. I haven't looked through the event log in windows but will post anything I find in an edit I haven't tried connecting (in Windows 7) to any other wireless network, since The fact that it works in Ubuntu suggests its Windows and not the router but I didn't change any wireless settings in windows before it being able to reach the Internet and not. Does anyone have any clue what could have happened. I opened to buying another router as this one is almost a year old :) but I would like to know whats going on here. Thanks in Advance! P.S. Sorry for how long my question is, I'm a little anxious (:

  Read the article

• RDP exits immediately after connecting to Windows Server 2008 R2

  - by carpat

  Background: I recently got a Windows cloud VPS server. I don't have much experience with server admin (I'm a programmer), and what little I do have is with linux servers. Ever since getting the server I've been having issues with RDP. I can connect about two or three times, after which point I can't connect until one of the tech guys "fixes" it (see below). When I connect, I can stay connected for hours with no problem. When the problem connecting starts, the first time I try to log in, the remote desktop window pops up, starts connecting, and then exits with "Your Remote Desktop session has ended". After that, for about 10-20 minutes if I try to connect again, the connections times out with Remote Desktop can't connect to the computer for one of these reasons: 1) Remote access on the server is not enabled 2) The remote computer is turned off 3) The remote computer is not available on the network then goes back to connecting once and immediately disconnecting. All of the updates are installed. The firewall has been correctly configured to let RDP traffic through. The remote setting is "Allow connections from computers running any version of Remote Desktop". I tried creating a second user, and when I can't connect, I can't connect to that user either. I've tried both soft and hard reboots, neither of which help. I've tried connecting from two different computers (both running Windows 7) from two different networks (work and home), and the behavior is the same. Everything else on the server continues to run fine (IIS-served http pages, Tomcat-served java pages, svn, ping). The "fix" that the tech guys supply is simply logging into the console on their end, after which point I can connnect 2 or 3 times again. The event viewer on the server has "authentication failure" (or something similar) events generated when I attempt to log in and can't. I can't get to the actual event at the moment as I'm currently in the can't connect stage, and waiting for the techs to log in. But when I searched for the event earlier this morning I couldn't find anything useful. Can anyone help?

  Read the article

• SIGINT and SIGTSTP ignored by most common applications

  - by Vašek Potocek

  After the last upgrade to my Fedora, a strange behaviour started occurring in X terminal applications. I can't seem to stop any process using Ctrl+C, it just results in printing ^C to the console. Similarly, Ctrl+Z prints ^Z and the process goes on. Both work well in non-graphical virtual consoles. I checked stty -a and it seems perfectly normal: speed 38400 baud; rows 24; columns 80; line = 0; intr = ^C; quit = ^\; erase = ^?; kill = ^U; eof = ^D; eol = M-^?; eol2 = M-^?; swtch = M-^?; start = ^Q; stop = ^S; susp = ^Z; rprnt = ^R; werase = ^W; lnext = ^V; flush = ^O; min = 1; time = 0; -parenb -parodd cs8 hupcl -cstopb cread -clocal -crtscts -ignbrk brkint -ignpar -parmrk -inpck -istrip -inlcr -igncr icrnl ixon -ixoff -iuclc ixany imaxbel iutf8 opost -olcuc -ocrnl onlcr -onocr -onlret -ofill -ofdel nl0 cr0 tab0 bs0 vt0 ff0 isig icanon iexten echo echoe echok -echonl -noflsh -xcase -tostop -echoprt echoctl echoke This is independent of the terminal (gnome-terminal, XFCE4 terminal, xterm). I later noticed that it may not be caused by the terminal at all: INT or TSTP sent directly to the respective process are ignored, too. This comprises various applications I used to terminate using Ctrl+C on a regular basis (and which often don't have any better means of exiting): cat, find, tail -f, java, ping, mplayer when stuck on a broken file... Even bash ignores Ctrl+C when I want to break a command line I have been entering and then changed my mind (no ^C is printed in this case). I need to delete it character by character (of which there may be hundreds if filename completion has been used) or intentionally run the unwanted command. Strangely enough, vim does recognize Ctrl+C—just to say its "use :quit", of course. This is extremely annoying and prevents me from working efficiently. Everything had been working until lately, maybe a week ago or so. I can not find any possible causes in Google, perhaps I'm trying wrong search terms or misidentifying the main problem. What could be it and how could I revert the standard behaviour, please? Update Ctrl+Z works sometimes. It seems that in the very first terminal I launch after logging in it stops the running command but stops working after that.

  Read the article

• Reliable access to Internet but not local network (not DNS or proxy issues)

  - by Ian Goldby

  I'm looking for help with a Vista Home Premium laptop that has trouble accessing any resource on our home network, but accesses the Internet just fine. The set-up is this: The Vista laptop and a MacBook Pro connect wirelessly to the router-modem. A Synology DS212j NAS drive has a wired connection to the router-modem. Devices on the local network are always referred to by IP address, so this cannot be a DNS issue. The MacBook Pro connects reliably to the NA via AFP (network shared folders), SMB (network shared folders) and HTTP. The Vista laptop connects to and browses sites on the Internet without any problems. It can log into the NAS via SMB and list the shared folders (so there is nothing wrong with the log-in credentials), but when it tries to open any of the folders Explorer just hangs with the spinning cursor for several minutes and then says "\192.168.1.64\shared\Photos is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions. The specified network name is no longer available." It can ping the NAS successfully. If I try to open the NAS drive's web interface, the browser just hangs. This is the same with IE, Firefox and Chrome. (There is no proxy.) I can log into the NAS drive with FTP and navigate directories, but when I try to list the contents of a directory with more than a handful of entries, the ftp client hangs. I set up a website on the MacBook. The Vista laptop was able to load some of the pages, but loading any of the images was very hit and miss. Images embedded in HTML pages never worked no matter how many times I reloaded the page, but when I linked directly to the image it did load (though several attempts were sometimes needed). I tried all of this with the Windows Firewall turned off, and with AVG turned off. That made no difference. I'd really appreciate any suggestions anyone can make. The fact that the Vista laptop has trouble with HTTP and FTP as well as SMB connections suggests to me that this is a problem at the TCP level or below. But don't forget it accesses sites outside the LAN with no problems.

  Read the article

• VPN Connection Causes Internal LAN Connection Loss with Server

  - by sleepisfortheweak

  I've tried configuring basic PPTP VPN at my small business using a number of different tutorials. As far as I can tell, the actual VPN connection worked fine, but upon connecting a client, the Server 'disappears' from the internal LAN. The RRAS service must be stopped before the connection is restored. My Setup: The network is simply a DSL Gateway/Router to the outside functioning as NAT/Firewall/DHCP. The server is a Win Server 2008 machine at fixed IP 192.168.1.200. The server has 1 NIC, so I used the 'custom' option when configuring RRAS. The RRAS settings should be default except that I've disabled ports for connection types I'm not using and reduced PPTP ports to 10. I've also created an address pool and disabled DHCP packet forwarding. The server only functions as a File Share and now a VPN Server. Local LAN computers all have mapped network shares to the server authenticated based on Local User/Group setup on the server. The Problem: The moment a client connects through VPN, the server 'disappears' from the local network. All mapped drives disconnect and there is no response to a ping 192.168.1.200. Even if the client disconnects, the server does not re-appear at that address until the RRAS service is stopped. I've Tried: Using an Address Pool inside and outside the local subnet. Using DCHP Relay Checking Inbound/Outbound filters (none enabled) The fact that nothing I've tried has had any effect, and that I can connect and successfully obtain an IP tells me that it's something more fundamental I'm missing. My gut tells me that it's something to do with the second IP address added by the VPN client somehow taking over the interface or traffic from the local LAN accidently getting routed to the VPN client instead of handled at the server once RRAS has become 'active' when a client connects. Hopefully this may be obvious to someone with real IT experience. I've been doing this a while and almost never been stumped. I'm starting to think it might actually be something tricky since my setup is pretty basic yet refuses to work. I'll be happy to include more info if this doesn't ring any bells right away for anyone. Thanks

  Read the article

• VLAN issues between linux kernels 2.6 / 3.3 in an ESX / Cisco environment

  - by David Griffith

  I shall attempt to explain an issue I have encountered - I have a VM running on esx 4.1 with an interface connected to VLAN800 via an access port on a cisco 3750. It runs linux - kernel 2.6.24, and has about 5 to 10 Mbit of chatter on 10.10.0.0/16 and various multicast addresses to look after. I needed to isolate certain devices from certain other devices on the network, with all of them having to talk to that one VM. No, the address space can't be separated, nor can the networks be easily vlan'd apart. The software on the VM listens to one interface only. Private vlans appear to be the way to go. So as a test, I built a bridge on the VM that globs together the vlans as needed. All good, everything works as expected. But occasionally (sigh) there's some latency that trips up a couple of profinet devices on the network because, you know, you're not really supposed to trunk real-time protocols around the place willy-nilly. I shift it to our test/backup server - works nicely, but I don't want it to be running on the test server as we muck around with that a lot. So I says to myself, "I'll put it on a new VM for testing and tweaking." I download a small linux distro with kernel 3.3, and install as a new VM with a the vlans as separate interfaces for testing. I power up the testing VM - ok. I bring up all the separate interfaces - ok. I can ping the production VM, see all sorts of traffic going past with tshark, etc. I build a bridge and put the primary vlan on it - the production VM running 2.6 immediately loses its multicast traffic - Unicast is fine. (?) I shut down the bridge - still no multicast traffic (!?) I power-cycle the production VM(!?!?) - multicast traffic returns. I trunk everything into the testing VM and create vlan interfaces under linux instead - same result, as soon as I start the bridge.... no multicast on the production VM. Ok, so I take a break and leave things alone. I decide to play with a couple of ubiquiti bullet radios - I'm testing various firmware as a side project. I flash a radio with Open-wrt-12.09. I enable a trunk on a port on a cisco on our network so I can muck around with multiple vlans and SSIDs I power up the radio and connect - ok. I create a vlan interface from the trunk.... the same vlan as the production VM wayyyyy over there, three cisco routers away. Ok. I bridge the vlan interface to the wifi interface and immediately get a phone call. The production VM has (suprise!) lost its multicast traffic. Again, nothing comes back until I power-cycle the VM. What the hell is going on?

  Read the article

< Previous Page | 101 102 103 104 105 106 107 108 109 110 111 112  | Next Page >