Search Results

Search found 4485 results on 180 pages for 'ssh keygen'.

Page 105/180 | < Previous Page | 101 102 103 104 105 106 107 108 109 110 111 112  | Next Page >

• Looking for suitable backup solution Mac OS X to offsite Centos 6 server 1TB of working data

  - by Brady

  I'll start by saying what we have in place currently: On site file server (Mac OS X Server) that is used by GFX designers and they have a working 1TB of data. Offsite server with 2TB available storage (Centos 6) Mac OS X server rsync data to offsite server every 6 hours (rsync -avz --delete --progress -e ssh ...) Mac OS X server does full data backup to LTO 4 tape on a 10 day recycle (Mon-Fri for 2 weeks) rsync pushes about 60GB of file changes a day. The problem: The onsite tape backup is failing as 1TB of graphics files don't compress well to fit onto a 800GB LTO4 tape. Backup is incredibly slow doing a full backup. Pain in the backside getting people to remember to change the tape. Often gets forgotten etc The quick solution: Buy LTO5 Drive and tapes. However this has been turned down because of the cost... What I would like: Something that works in the same way rysnc works. Only changed data is sent over the wire and can be scheduled to run multiple times during the day. Data that is sent is compressed and sent over SSH. Something that keeps a 14day retention but doesn't keep duplicate data So as an example if I have 1TB of working data and 60GB of changes are made each day then I expect around 1.84TB of data to be stored on the offsite server. To work with the Mac OS X server and Centos 6 server. Not cost an arm and a leg. Must be a cheaper solution than buying an LTO5 drive with tapes (around £1500). Be able to be setup to run autonomously. Have some sort of control panel that will allow an admin to easily restore a file/folder. Any recommendations?

  Read the article

• rsync general question

  - by CaptnLenz

  I'm trying to use rsync. At first, everything looks very good: rsync -Pniahv -e ssh /home/xxx/Videos/ [email protected]:"/shares/Public/Shared\ Videos/" --stats ... <f+++++++++ Serien/blah.avi <f+++++++++ Serien/blah S01E01 <f+++++++++ Serien/blah - S01E02 <f+++++++++ Serien/blah - S01E03 <f+++++++++ Serien/blah - S01E04 <f+++++++++ Serien/blah - S01E05 <f+++++++++ Serien/blah - S01E06 <f+++++++++ Serien/blah - S01E07 ... Number of files: 232 Number of files transferred: 223 Total file size: 118.24G bytes Total transferred file size: 117.51G bytes Literal data: 0 bytes Matched data: 0 bytes File list size: 9.46K File list generation time: 0.001 seconds File list transfer time: 0.000 seconds Total bytes sent: 10.18K Total bytes received: 712 After that, i copied some of the files manually and runned rsync again in dry mode: rsync -Pniahv -e ssh /home/xxx/Videos/ [email protected]:"/shares/Public/Shared\ Videos/" --stats ... <f..tpo.... Serien/blah.avi <f..tpo.... Serien/blah S01E01 <f..tpo.... Serien/blah - S01E02 <f..tpo.... Serien/blah - S01E03 <f..tpo.... Serien/blah - S01E04 <f..tpo.... Serien/blah - S01E05 <f..tpo.... Serien/blah - S01E06 <f..tpo.... Serien/blah - S01E07 ... Number of files: 232 Number of files transferred: 223 Total file size: 118.24G bytes Total transferred file size: 117.51G bytes Literal data: 0 bytes Matched data: 0 bytes File list size: 9.46K File list generation time: 0.001 seconds File list transfer time: 0.000 seconds Total bytes sent: 10.18K Total bytes received: 712 Why hasn't changed something in the --stats, although only the permissions and the timestamp have to be updated and not the full files need to be copied?

  Read the article

• iptables-restore: line 1 failed

  - by Doug

  Hello, I am new to servers, and I was following this guide and it failed on the first command instructed. Could anyone give me a hand? http://wiki.debian.org/iptables ~ZORO~:/etc# iptables-restore < /etc/iptables.test.rules iptables-restore: line 1 failed Edit: iptables.test.rules ~ZORO~:/etc# cat /etc/iptables.test.rules *filter # Allows all loopback (lo0) traffic and drop all traffic to 127/8 that doesn't use lo0 -A INPUT -i lo -j ACCEPT -A INPUT -i ! lo -d 127.0.0.0/8 -j REJECT # Accepts all established inbound connections -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT # Allows all outbound traffic # You could modify this to only allow certain traffic -A OUTPUT -j ACCEPT # Allows HTTP and HTTPS connections from anywhere (the normal ports for websites) -A INPUT -p tcp --dport 80 -j ACCEPT -A INPUT -p tcp --dport 443 -j ACCEPT # Allows SSH connections for script kiddies # THE -dport NUMBER IS THE SAME ONE YOU SET UP IN THE SSHD_CONFIG FILE -A INPUT -p tcp -m state --state NEW --dport 30000 -j ACCEPT # Now you should read up on iptables rules and consider whether ssh access # for everyone is really desired. Most likely you will only allow access from certain IPs. # Allow ping -A INPUT -p icmp -m icmp --icmp-type 8 -j ACCEPT # log iptables denied calls (access via 'dmesg' command) -A INPUT -m limit --limit 5/min -j LOG --log-prefix "iptables denied: " --log-level 7 # Reject all other inbound - default deny unless explicitly allowed policy: -A INPUT -j REJECT -A FORWARD -j REJECT COMMIT

  Read the article

• Managing Linux Directory Permissions & SFTP

  - by Dizzle

  Good morning; I have a RHEL 5.7 web server configured to allow SSH/SFTP only by specific groups. I'd like for content managers to upload content to their respective directories and have that content inherit the user/group ownership of the directory regardless of upload method or application. For example: John is in group "web" for SSH/SFTP rights and "finance" for directory permissions, and uploads to directory "webstuff" via SFTP. Directory "webstuff" has permissions of "2760" (rwxrws---), and ownership of "apache:finance". If John uploads an update to an existing file in "webstuff", the ownership of the file stays at "apache:finance". If John uploads a new file to "webstuff", the ownership of the file is "john:finance". My desire is to have any file from John uploaded to "webstuff" to change to the directory's owner. I've tried with setuid and setgid both set, but the user-ownership didn't take. I've seen mentions on ServerFault of using ACL's, or a chrooted jail for SFTP but I have yet to configure and test them, and I don't know if they're a viable solution (they could be, I just don't know because I've never done either). Any thoughts and assistance would be greatly appreciated.

  Read the article

• Ubuntu Postfix email account with forward

  - by Mika

  I have an Ubuntu 12.04 server with Postfix installed. In Postfix installation I used this guide https://help.ubuntu.com/community/Postfix. I didn't go through all of that, just the sudo dpkg-reconfigure postfix part. I have created user accounts to my server and the users home directories contain a .forward file which have only one row the email address to forward to. I have defined dns A records for the names www.mydomain.com and mydomain.com But if I send an email to [email protected] it doesn't get forwarded. Actually I can't see any sign about any email ever visiting my server. My firewall is defined to allow incoming traffic for ports 80, 443 and 22. For outgoing traffic it allows ports 587 and 22. The exact definitions are below. Should I allow also outgoing http (port 80)? or maybe port 25? # Allow ssh in iptables -A INPUT -i eth0 -p tcp --dport 22 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --sport 22 -m state --state ESTABLISHED -j ACCEPT # Allow incoming HTTP iptables -A INPUT -i eth0 -p tcp --dport 80 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --sport 80 -m state --state ESTABLISHED -j ACCEPT # Allow incoming HTTPS iptables -A INPUT -i eth0 -p tcp --dport 443 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A OUTPUT -o eth0 -p tcp --sport 443 -m state --state ESTABLISHED -j ACCEPT # Allow outgoing SSH iptables -A OUTPUT -o eth0 -p tcp --dport 22 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A INPUT -i eth0 -p tcp --sport 22 -m state --state ESTABLISHED -j ACCEPT # Allow outgoing emails iptables -A OUTPUT -o eth0 -p tcp --dport 587 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A INPUT -i eth0 -p tcp --sport 587 -m state --state ESTABLISHED -j ACCEPT Edits: I found lines from my syslog telling me that there were incoming traffic for port 25 which was blocked. The sender ip's for those packages were trustworthy, so I opened also port 25. Now I can see some Postfix logging in my syslog. It looks like it is at least trying to forward emails. I haven't yet received any forwarder emails into my gmail mail box.

  Read the article

• IP-dependent local port-forwarding on Linux

  - by chronos

  I have configured my server's sshd to listen on a non-standard port 42. However, at work I am behind a firewall/proxy, which only allow outgoing connections to ports 21, 22, 80 and 443. Consequently, I cannot ssh to my server from work, which is bad. I do not want to return sshd to port 22. The idea is this: on my server, locally forward port 22 to port 42 if source IP is matching the external IP of my work's network. For clarity, let us assume that my server's IP is 169.1.1.1 (on eth1), and my work external IP is 169.250.250.250. For all IPs different from 169.250.250.250, my server should respond with an expected 'connection refused', as it does for a non-listening port. I'm very new to iptables. I have briefly looked through the long iptables manual and these related / relevant questions: http://serverfault.com/questions/57872/iptables-question-forwarding-port-x-to-an-ssh-port-of-different-machine-on-the-n http://serverfault.com/questions/140622/how-can-i-port-forward-with-iptables However, those questions deal with more complicated several-host scenarios, and it is not clear to me which tables and chains I should use for local port-forwarding, and if I should have 2 rules (for "question" and "answer" packets), or only 1 rule for "question" packets. So far I have only enabled forwarding via sysctl. I will start testing solutions tomorrow, and will appreciate pointers or maybe case-specific examples for implementing my simple scenario. Is the draft solution below correct? iptables -A INPUT [-m state] [-i eth1] --source 169.250.250.250 -p tcp --destination 169.1.1.1:42 --dport 22 --state NEW,ESTABLISHED,RELATED -j ACCEPT Should I use the mangle table instead of filter? And/or FORWARD chain instead of INPUT?

  Read the article

• NAT vs public IP (and blocked ports)

  - by user1646166

  I have a problem with my ISP. They say that they don't block any ports and I have public IP, while I think these both statements are false. Before I talk to them again (which is really tough when my understanding of these terms is different than theirs) I would like to make some things clear. It seems like my computer is behind NAT (is it possible to have public IP and be behind NAT at the same moment?). When I check my IP, through some external server, and type that IP into browser I get a home page of some router (not mine). Isn't that a proof that my IP isn't public? Also, I have problems with making connections via some ports. E.g. when I'm trying to connect through some high port ( 1023) via SSH, it doesn't work. Is it possible that certain range of outgoing ports from my computer are blocked? Or is it simply because that my ssh client (PuTTY) can't receive incoming packets because of blocked incoming ports? To avoid some questions: it's not a problem with my router, I tried connecting my PC directly and it also didn't work, while having connected by 3G using phone with USB tethering, it does work. Thanks!

  Read the article

• EC2 instance is blocking all outbound connections, how to diagnose/fix?

  - by Fraggle

  My EC2 instance is blocking all outbound connections. wget http://www.google.com ==> Hangs ping google.com ==>hangs ssh user@anyserver ==>hangs I ran : sudo iptables -F to eliminate all rules to no avail AWS Management console shows Security Group for that instance has Inbound rule allowing ssh and port 80. Can't find anything about Outbound rules there. Rebooted instance, no change. If anyone knows how to diagnose or fix, please help. Adding info: [ec2-user@ip-10-112-62-73 ~]$ ifconfig eth0 Link encap:Ethernet HWaddr 12:31:3D:06:31:BB inet addr:10.112.62.73 Bcast:10.112.63.255 Mask:255.255.254.0 inet6 addr: fe80::1031:3dff:fe06:31bb/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1933 errors:0 dropped:0 overruns:0 frame:0 TX packets:1764 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:164075 (160.2 KiB) TX bytes:343256 (335.2 KiB) Interrupt:9 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:672 (672.0 b) TX bytes:672 (672.0 b) [ec2-user@ip-10-112-62-73 ~]$ ip route show 10.112.62.0/23 dev eth0 proto kernel scope link src 10.112.62.73 default via 10.112.62.1 dev eth0

  Read the article

• Ubuntu Pound Reverse Proxy Load Balancing Based off active server load?

  - by Andrew

  I have Pound installed on a loadbalancer. It seems to work okay, except that it randomly assigns the backend server to forward the request to. I've put 1 backend machine under so much load that it went into using swap, and I can't even ssh into it to test this scenareo. I would like the loadbalancer to realize that the machine is overloaded, and send it to a different backend machine. However it doesn't. I've read the man page and it seems like the directive "DynScale 1" is what would monitor this, but it still redirects to the overloaded server. I've also put in "HAport 22" to the backend figuring since I can't ssh in, neither could the loadbalancer and it would consider the backend server dead until it gets rid of the load and responds, but that didn't help either. If anyone could help with this, I'd appreciate it. My current config is below. ###################################################################### ## global options: User "www-data" Group "www-data" #RootJail "/chroot/pound" ## Logging: (goes to syslog by default) ## 0 no logging ## 1 normal ## 2 extended ## 3 Apache-style (common log format) LogLevel 3 ## check backend every X secs: Alive 5 DynScale 1 Client 1200 TimeOut 1500 # poundctl control socket Control "/var/run/pound/poundctl.socket" ###################################################################### ## listen, redirect and ... to: ## redirect all requests on port 80 to SSL ListenHTTP Address 192.168.1.XX Port 80 Service Redirect "https://xxx.com/" End End ListenHTTPS Address 192.168.1.XX Port 443 Cert "/files/www.xxx.com.pem" Service BackEnd Address 192.168.1.1 Port 80 HAport 22 End BackEnd Address 192.168.1.2 Port 80 HAport 22 End End End

  Read the article

• How to grant read/write to specific user in any existent or future subdirectory of a given directory? [migrated]

  - by Samuel Rossille

  I'm a complete newbie in system administration and I'm doing this as a hobby. I host my own git repository on a VPS. Let's say my user is john. I'm using the ssh protocol to access my git repository, so my url is something like ssh://[email protected]/path/to/git/myrepo/. Root is the owner of everything that's under /path/to/git I'm attempting to give read/write access to john to everything which is under /path/to/git/myrepo I've tried both chmod and setfacl to control access, but both fail the same way: they apply rights recursively (with the right options) to all the current existing subdirectories of /path/to/git/myrepo, but as soon as a new directory is created, my user can not write in the new directory. I know that there are hooks in git that would allow me to reapply the rights after each commit, but I'm starting to think that i'm going the wrong way because this seems too complicated for a very basic purpose. Q: How should I setup my right to give rw access to john to anything under /path/to/git/myrepo and make it resilient to tree structure change ? Q2: If I should take a step back change the general approach, please tell me.

  Read the article

• Amazon EC2 instance missing Network Interface

  - by Sergiks

  I am running Linux on a t1.micro instance at Amazon EC2. Once I noticed bruteforce ssh login attemtps from a certain IP, after litle Googling I issued the two following commands (other ip): iptables -A INPUT -s 202.54.20.22 -j DROP iptables -A OUTPUT -d 202.54.20.22 -j DROP Either this, or maybe some other actions like yum upgrade perhaps, caused the follwing fiasco: after rebooting the server, it came up without the Network Interface! I only can connect to it through AWS Management Console JAVA ssh client - via local 10.x.x.x address. Console's Attach Network Interface as well as Detach.. are greyed out for this instance. Network Interfaces item at the left does not offer any Subnets to choose from, to create a new N.I. Please advice, how can I recreate a Network Interface for the instance? Upd. The instance is not accessible from outside: cannot be pinged, SSH'ed or connected by HTTP on port 80. Here's the ifconfig output: eth0 Link encap:Ethernet HWaddr 12:31:39:0A:5E:06 inet addr:10.211.93.240 Bcast:10.211.93.255 Mask:255.255.255.0 inet6 addr: fe80::1031:39ff:fe0a:5e06/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1426 errors:0 dropped:0 overruns:0 frame:0 TX packets:1371 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:152085 (148.5 KiB) TX bytes:208852 (203.9 KiB) Interrupt:25 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) What is also unusual: a new micro instance I created from scratch, with no relation to the troubled one, was not pingable too.

  Read the article

• What is the ip range of EC2

  - by Nicolas Kassis

  I'd like to setup a rule to block ssh request from EC2 since I've been seeing a large amount of ssh based attack from there and was wondering if anyone knew what their IP ranges are. EDIT: Thank you for the answer, I went ahead and implemented the iptables rules as follow. I ignore all traffic for the moment. Logging it just to see if the rules are working and for stats on how much crap EC2 is sending out ;) #EC2 Blacklist $IPTBLS -A INPUT -s 67.202.0.0/18 -j LOG --log-prefix "<firewall> EC2 traffic " $IPTBLS -A INPUT -s 67.202.0.0/18 -j DROP $IPTBLS -A INPUT -s 72.44.32.0/19 -j LOG --log-prefix "<firewall> EC2 traffic " $IPTBLS -A INPUT -s 72.44.32.0/19 -j DROP $IPTBLS -A INPUT -s 75.101.128.0/17 -j LOG --log-prefix "<firewall> EC2 traffic " $IPTBLS -A INPUT -s 75.101.128.0/17 -j DROP $IPTBLS -A INPUT -s 174.129.0.0/16 -j LOG --log-prefix "<firewall> EC2 traffic " $IPTBLS -A INPUT -s 174.129.0.0/16 -j DROP $IPTBLS -A INPUT -s 204.236.192.0/18 -j LOG --log-prefix "<firewall> EC2 traffic " $IPTBLS -A INPUT -s 204.236.192.0/18 -j DROP $IPTBLS -A INPUT -s 204.236.224.0/19 -j LOG --log-prefix "<firewall> EC2 traffic " $IPTBLS -A INPUT -s 204.236.224.0/19 -j DROP $IPTBLS -A INPUT -s 79.125.0.0/17 -j LOG --log-prefix "<firewall> EC2 traffic " $IPTBLS -A INPUT -s 79.125.0.0/17 -j DROP

  Read the article

• How do you change a Cisco ASA 5510 management interface?

  - by Sam Sanders

  I want to add a redundant interface to my Cisco ASA 5510. The management interface is currently using Ethernet0/1 (10.1.25.254/24) one of the interface I want to use for the redundant interfaces. So I wanted to setup Management0/0 as the new management interface. The other interface I want to use is Ethernet0/2 (10.1.0.254/24) for the redundant interface. The Ethernet0/3 (10.1.251.5/24) interface is not going to be part of the redundant interface. I gave the Management0/0 an IP address of 10.1.254.5, and was able to connect a win7 box to Management0/0 and use 10.1.254.5 as a gateway; and ping another address on the (10.1.251.0/24) network, but I can't ping the interface (10.1.254.5) itself. I also can't use ASDM/SSH to log onto the ASA at 10.1.254.5. I setup rules in Configuration Device Management Management Access ASDM/HTTPS/Telnet/SSH. That look like the original rules for the Ethernet0/1 interface. The last thing I can think to try would be to change the Configuration Device Management Management Access Management Interface. I'm a bit nervous about changing it, the description of it is a bit vague. What it's going to do if I change it? What is the correct way to change a management interface?

  Read the article

• VPN on a ubuntu server limited to certain ips

  - by Hultner

  I got an server running Ubuntu Server 9.10 and I need access to it and other parts of my network sometimes when not at home. There's two places I need to access the VPN from. One of the places to an static IP and the other got an dynamic but with DynDNS setup so I can always get the current IP if I want to. Now when it comes to servers people call me kinda paranoid but security is always my number one priority and I never like to allow access to the server outside the network therefor I have two things I have to have on this VPN. One it shouldn't be accessiable from any other IP then these 2 and two it has to use a very secure key so it will be virtually impossible to bruteforce even from the said IP´s. I have no experience what so ever in setting up VPNs, I have used SSH tunneling but never an actuall VPN. So what would be the best, most stable, safest and performance effiecent way to set this up on a Ubuntu Server? Is it possible or should I just set up some kind of SSH Tunnel instead? Thanks on beforehand for answers.

  Read the article

• dpkg broken while upgrading Debian Etch to Lenny

  - by artvolk

  Good day! While trying to recover a box to lenny it seems I've broken things. It upgrades libc and glib after that dpkg seems to be broken. I can run apt-get, but it gets segmentation fault from dpkg: # apt-get -f install Reading package lists... Done Building dependency tree... Done 0 upgraded, 0 newly installed, 0 to remove and 316 not upgraded. 9 not fully installed or removed. Need to get 0B of archives. After unpacking 0B of additional disk space will be used. /bin/sh: line 1: 4606 Segmentation fault /usr/sbin/dpkg-preconfigure --apt E: Sub-process /usr/bin/dpkg received a segmentation fault. I can login via SSH but even ls is not working: # ls Segmentation fault Is there anything I can do remotelly via SSH? # ldd /bin/ls linux-gate.so.1 => (0xffffe000) librt.so.1 => /lib/tls/i686/cmov/librt.so.1 (0xb7fc8000) libacl.so.1 => /lib/libacl.so.1 (0xb7fc2000) libselinux.so.1 => /lib/libselinux.so.1 (0xb7fac000) libc.so.6 => /lib/i686/cmov/libc.so.6 (0xb7e51000) libpthread.so.0 => /lib/tls/i686/cmov/libpthread.so.0 (0xb7e3f000) /lib/ld-linux.so.2 (0xb7fd8000) libattr.so.1 => /lib/libattr.so.1 (0xb7e3b000) libdl.so.2 => /lib/i686/cmov/libdl.so.2 (0xb7e37000) libsepol.so.1 => /lib/libsepol.so.1 (0xb7df6000) It seems I've temporary fixed it with: # touch /etc/ld.so.nohwcap From here: http://saintaardvarkthecarpeted.com/blog/archive/2005/08/_etc_ld_so_nohwcap.html

  Read the article

• How do I format this regex so it will work in fail2ban?

  - by chapkom

  I've just installed fail2ban on my CentOS server in response to an SSH brute force attempt. The default regular expressions in fail2ban's sshd.conf file do not match any entries in audit.log, which is where SSH seems to be logging all connection attempts, so I am trying to add an expression that will match. The string I am trying to match is as follows: type=USER_LOGIN msg=audit(1333630430.185:503332): user pid=30230 uid=0 auid=500 subj=user_u:system_r:unconfined_t:s0-s0:c0.c1023 msg='acct="root": exe="/usr /sbin/sshd" (hostname=?, addr=<HOST IP>, terminal=sshd res=failed)' The regular expression I am attempting to use is: ^.*addr=<HOST>, terminal=sshd res=failed.*$ I've used regextester.com and regexr to try to build the regex. The testers give me a match for this regex:^.*addr=\d{1,3}\.\d{1,3}\.\d{1,3}\.\d{1,3}, terminal=sshd res=failed.*$ but fail2ban-regex complains if I don't use the <HOST> tag in the regex. However, using ^.*addr=<HOST>, terminal=sshd res=failed.*$ gives me 0 matches. At this point, I am totally stuck and I would greatly appreciate any assistance. What am I doing wrong in the regex I am trying to use?

  Read the article

• How can I switch from a custom linux network namespace back to the default one?

  - by Martin

  With ip netns exec you can execute a command in a custom network namespace - but is there also a way to execute a command in the default namespace? For example, after executing these two commands: sudo ip netns add test_ns sudo ip netns exec test_ns bash How can the newly created bash execute programs in the default network namespace? There is no ip netns exec default or anything similar as far as I've found. My scenario is: I want to run a SSH server in a separate network namespace (to keep the rest of the system unaware of the network connection, as the system is used for network testing), but want to be able to execute programs in the default network namespace via the SSH connection. What I've found out so far: Created network namespaces are listed as files under /var/run/netns (but there is no file for the default namespace) The ip netns exec code can be found here: http://git.kernel.org/cgit/linux/kernel/git/shemminger/iproute2.git/tree/ip/ipnetns.c#n132 - I haven't grasped everything that it is doing yet, but it doesn't look very promising. ip netns identify $$ as suggested by Howto query and change network namespace on linux? returns nothing when in the default network namespace

  Read the article

• Webserver python update script

  - by ThePyCoder

  So i have made this website on which you can trade stocks based on real stock quotes with virtual money. The stock quotes are in a MySQL database and are updated using a python script which runs every minute or so. Now, this works fine on my local machine with xampp but how about moving the project to a commercial web server? Basically I want my page hosted by a professional company but do those kind of servers support python scripts running in the background? Because a dedicated server would be to expensive and the script does some other sql tasks too so it can't be replaced by PHP or so... So, are there any good web hosting services out there who give me the possibility of running a script in the background and hosting a website in the foreground? For what server specifications do i have to look for? Thnx in advance! PS: I've done some research, and I found a python supporting web host WITH ssh support. Is that what I need? Or is the ssh not allowed to start processes?

  Read the article

• Setting up xpra for client use in OS X

  - by Jonathan

  I've been trying to get xpra to run on OS X for the last few days to connect to my Ubuntu server. Note that there's a GUI for it called shifter, but that (at least on OS X) is still far too buggy. For those who don't know what xpra is, if you know what screen is, it's like screen for GUI X Windows apps tunneled over ssh. You can render a remote X app locally so it's faster than sending a series of compresses screen shots (like VNC), but with xpra you can disconnect and reconnect on different computers. To get the basic functionality you can just type "ssh -X server.location" and any GUI app you open from the command line will open locally. I've been able to get xpra to build by doing the following: Download pari-all-0.0.6.tar.gz from the xpra site listed under upstream and untar it. Issue the following Mac Ports command (Dependencies thanks to RogBlog): sudo port install python25 python26 py26-pyrex py26-gtk xorg-libXtst py25-gobject py25-gtk py25-nose py26-nose xorg-libXdamage xorg-libXcomposite xorg-libXtst xorg-libXfixes In the upstream list of v0.0.06 patches (NOT 0.0.8pre!) on the xpra site listed above, download mswindows-conditional-pyrex.patch. Open the patch with your favorite text editor and change the single occurrence of "win" in it to "darwin". Apply the patch to setup.py. Run do-build in the command line. Now where I'm stumped: how do I run xpra? The build produces a sub directory called install/bin in which xpra is located, but when I try to run it I get the following error: Traceback (most recent call last): File "./xpra", line 4, in import xpra.scripts.main ImportError: No module named xpra.scripts.main There is a file called main.py under xpra/scripts, but I don't know any python and I'm not sure if this is what it's looking for, and what to do with it even if it is. My goal is to set up xpra so I can install it into /usr/bin (or some other common path for executables) and execute it whenever I please. What do I do next?

  Read the article

• How to connect to a remote server and run some code on that particular server?

  - by seedeg

  I am implementing an automated backup scheme so I created a shell script which first creates SQL Dumps for all MySQL databases, then it retrieves all the websites from the /var/www of a remote server. The latter is working as I am using rsync to get the remote files. However, obviously, the MySQL dumps being retrieved are the ones on the local server which is not what I want. I want to get the SQL Dumps from the remote server as well. I have a tunnel between the local and remote server which I can connect without using any password (I added the public key to the authorized_hosts), so I tried to add the following code to the script: ssh [email protected] Then I tried to retrieve the SQL dumps and then I exit from the remote server. However this does not work as I still have to enter exit manually in the terminal for the SQL dumps to be retrieved from the remote host. I don't know why this is happening. Basically this is what the script is trying to do: //connect to remote server ssh [email protected] //retrieve SQL dumps //code to retrieve... //exit from remote server exit //use rsync to get remote files of /var/www from local server (working) Is there a way to connect to the remote host AND run the script's code ON THAT remote host? Many thanks in advance

  Read the article

• Why would I need a firewall if my server is well configured?

  - by Aitch

  I admin a handful of cloud-based (VPS) servers for the company I work for. The servers are minimal ubuntu installs that run bits of LAMP stacks / inbound data collection (rsync). The data is large but not personal, financial or anything like that (ie not that interesting) Clearly on here people are forever asking about configuring firewalls and such like. I use a bunch of approaches to secure the servers, for example (but not restricted to) ssh on non standard ports; no password typing, only known ssh keys from known ips for login etc https, and restricted shells (rssh) generally only from known keys/ips servers are minimal, up to date and patched regularly use things like rkhunter, cfengine, lynis denyhosts etc for monitoring I have extensive experience of unix sys admin. I'm confident I know what I'm doing in my setups. I configure /etc files. I have never felt a compelling need to install stuff like firewalls: iptables etc. Put aside for a moment the issues of physical security of the VPS. Q? I can't decide whether I am being naive or the incremental protection a fw might offer is worth the effort of learning / installing and the additional complexity (packages, config files, possible support etc) on the servers. To date (touch wood) I've never had any problems with security but I am not complacent about it either.

  Read the article

• I want to use OpenVPN to access the web and email from China. How?

  - by gaoshan88

  My question: How do I use my already existing OpenVPN setup to enable secure, remote web surfing and email checking from open wireless hotspots? Some long winded details: I am running Ubuntu and have OpenVPN up and working fine as a server. My client machine connects fine as well. However, that just gets me a secure connection to my home network. What I want is to be able to access my VPN server and surf the web or check email securely from anywhere with an open wireless connection. I am frequently in China and having secure, unblocked access would be a boon (especially since I like to work from tea houses and coffee shops and I've already had a password sniffed and hacked once). I already know how to tunnel over SSH via a SOCKS proxy using something like: ssh -ND 8887 -p 22 [email protected] but since I have OpenVPN I figure why not try it? So... what are the steps involved in making it so I can connect to my VPN and the surf and check mail to my hearts content (slowly to be sure but at least it wold be secure). Thx!

  Read the article

• Apache can't get viewed from outside of my LAN

  - by Javier Martinez

  I fixed it in PORTS TRIGGER menu of my router. Thanks you anyway I have a weird problem related with (i think) my cable-router and my configured vhosts in Apache2. The point is I can't access from outside of my LAN to any of my configured vhosts if I set the http port of Apache to 80 and i add a NAT rule for it. Otherwise, if I set my Apache port to 81 (or any else) with its respective NAT rule on my router it works. My router is an ARRIS TG952S and I am using Apache/2.2.22 (Debian) ports.conf NameVirtualHost *:80 Listen 80 vhost1.mydomain.net.conf <VirtualHost *:80> ServerAdmin webmaster@localhost ServerName vhost1.mydomain.net ServerAlias vhost1.mydomain.net www.vhost1.mydomain.net vhost2.mydomain.net.conf <VirtualHost *:80> ServerAdmin webmaster@localhost ServerName vhost2.mydomain.net ServerAlias vhost2.mydomain.net www.vhost2.mydomain.net DNS records (using FreeDNS) are: mydomain.net --> pointing to another server vhost1.mydomain.net --> pointing to my server vhost2.mydomain.net --> pointing to my server iptables -L -n Chain INPUT (policy ACCEPT) target prot opt source destination fail2ban-apache-noscript tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 80,443 fail2ban-apache tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 80,443 fail2ban-ssh tcp -- 0.0.0.0/0 0.0.0.0/0 multiport dports 22 Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain fail2ban-apache (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain fail2ban-apache-noscript (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 Chain fail2ban-ssh (1 references) target prot opt source destination RETURN all -- 0.0.0.0/0 0.0.0.0/0 Thanks you

  Read the article

• why Thinkpad T410s intermittent keyboard death?

  - by patrickmdnet

  I have a Thinkpad T410s running Windows 7 64-bit. I have had it for three months. It has the latest BIOS (1.41) and trackpad drivers. In the last week I have started to notice that the keyboard intermittently stops working. Specifically, keystrokes have no effect, including Fn-F12 (shutdown) and Ctrl-Alt-Del. The LED on the capslock key does not turn on or off. Whatever state the lighted keys (e.g. mute) were in remains. The trackpad and trackpoint work properly, and I can close apps and properly shut down the machine. When I attach a USB keyboard it is recognized, but no keys work. If I run the Lenovo keyboard test, all the keys register properly and the caps lock light works again. When I quit the test app, the caps lock light stops working. If I hit Fn-F12 while the keyboard test is running, it goes into hibernation. When the machine comes back from hibernation, once I exit the keyboard test I again cannot do any input on the keyboard. I'm pretty convinced there is a software or driver problem. I never saw this the first three months I had the laptop. I do not recall installing anything recently. I am sure I've received some Windows security updates. I tried using wired networking instead of wireless - no difference. There doesn't appear to be any inciting event; it usually happens when I am working over ssh. I switched from rxvt+ssh to Putty and the problem still occurs. Any ideas?

  Read the article

• Debian 6: setting up FTP just for website editing

  - by David Oliver

  I have a VPS using Debian 6.0. Currently, SSH is set to not accept password logins, and only key-based ones. A person who needs to work on one particular website (a vhost) wishes to use FTP. He doesn't need/want SSH. How can I set up FTP access for him, enabling him to have write permissions for all files in the relevant directory, and only the relevant directory? The directory is /srv/www/domainname.com/public_html Currently, all directories and files in that directory belong to www-data:www-data and are 644/755. I've installed vsftpd and have been reading some guides, but they all seem to deal with allowing multiple users to have their own user-named directories which isn't what I'm after. I can't seem to work out how to simply define one FTP user with a password that has access to one directory of my choosing. This is my first experience of setting up an FTP server. Thanks. Edit: have also found this - maybe I should be using ProFTPd, or can vsftpd also do what I want?

  Read the article

< Previous Page | 101 102 103 104 105 106 107 108 109 110 111 112  | Next Page >