Search Results

Search found 28429 results on 1138 pages for 'ubuntu'.

Page 105/1138 | < Previous Page | 101 102 103 104 105 106 107 108 109 110 111 112  | Next Page >

• Package upgrade on Ubuntu raid server and grub setup issue

  - by RecNes

  I have remote Ubuntu 10.10 server running on raid system. I did package upgrade yesterday night for security reasons. During the upgrade, grub installation screen appeared and asked me which partition I wanted to install grub. Options are sda,sdb,md1 and md2. I decide to install them on both sda and sdb partitions. I wondering, was I make true decision? If machine get reboot is it can be boot up safely? You can find fdisk output and fstab mount points below: Fstab: proc /proc proc defaults 0 0 none /dev/pts devpts gid=5,mode=620 0 0 /dev/md0 none swap sw 0 0 /dev/md1 /boot ext3 defaults 0 0 /dev/md2 / ext3 defaults 0 0 Fdisk: Disk /dev/sda: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00029bb5 Device Boot Start End Blocks Id System /dev/sda1 1 262 2102562 fd Linux raid autodetect /dev/sda2 263 295 265072+ fd Linux raid autodetect /dev/sda3 296 91201 730202445 fd Linux raid autodetect Disk /dev/md0: 2152 MB, 2152923136 bytes 2 heads, 4 sectors/track, 525616 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md0 doesn't contain a valid partition table Disk /dev/md1: 271 MB, 271319040 bytes 2 heads, 4 sectors/track, 66240 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md1 doesn't contain a valid partition table Disk /dev/md2: 747.7 GB, 747727224832 bytes 2 heads, 4 sectors/track, 182550592 cylinders Units = cylinders of 8 * 512 = 4096 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/md2 doesn't contain a valid partition table Disk /dev/sdb: 750.2 GB, 750156374016 bytes 255 heads, 63 sectors/track, 91201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00088969 Device Boot Start End Blocks Id System /dev/sdb1 1 262 2102562 fd Linux raid autodetect /dev/sdb2 263 295 265072+ fd Linux raid autodetect /dev/sdb3 296 91201 730202445 fd Linux raid autodetect

  Read the article

• Patching Synaptics Driver In Ubuntu

  - by danben

  I've got an HP Envy with the new Synaptics Clickpad - the device is not supported out of the box by Ubuntu, so I downloaded this patch (https://patchwork.kernel.org/patch/67335/), applied it to synaptics.c in the linux kernel source, rebuilt the kernel and booted from it. Nothing changed. I'm new to Linux and don't know much about driver configuration; how can I check that the newly-produced synaptics.o file is actually being used somewhere? Or if it is obvious, what step did I leave out? Separately, I tried following the instructions in this thread: http://georgia.ubuntuforums.org/showpost.php?p=8989185&postcount=11 There, someone posted the patch along with a Makefile and instructions for installation. When I followed those, my mouse stopped working altogether. Not desirable, but at least I know it had some effect. The Makefile is posted below; I get the gist of what it's doing, but don't have enough knowledge to figure out why it would cause the device to stop responding entirely. obj-m := psmouse.o psmouse-objs := psmouse-base.o synaptics.o psmouse-$(CONFIG_MOUSE_PS2_ALPS) += alps.o psmouse-$(CONFIG_MOUSE_PS2_ELANTECH) += elantech.o psmouse-$(CONFIG_MOUSE_PS2_OLPC) += hgpk.o psmouse-$(CONFIG_MOUSE_PS2_LOGIPS2PP) += logips2pp.o psmouse-$(CONFIG_MOUSE_PS2_LIFEBOOK) += lifebook.o psmouse-$(CONFIG_MOUSE_PS2_TRACKPOINT) += trackpoint.o psmouse-$(CONFIG_MOUSE_PS2_TOUCHKIT) += touchkit_ps2.o KDIR := /lib/modules/$(shell uname -r)/build PWD := $(shell pwd) default: $(MAKE) -C $(KDIR) SUBDIRS=$(PWD) modules install: @cp psmouse.ko /lib/modules/$(shell uname -r)/kernel/drivers/input/mouse/

  Read the article

• Mysql Cluster not working on Ubuntu

  - by user53864

  I am unable to setup MySQL Cluster on ubuntu servers. As a starting point I started from the link but I am not successful and the tar ball version I download is 6.3.45. As I wanted to test the mysql cluster, the Data node and SQL node are same but sql never appeared as connected in management node console and it looks like below. [ndbd(NDB)] 2 node(s) id=2 @192.168.1.107 (Version: version number, Nodegroup: 0, Master) id=3 @192.168.1.108 (Version: version number, Nodegroup: 0) [ndb_mgmd(MGM)] 1 node(s) id=1 @192.168.1.105 (Version: version number) [mysqld(API)] 2 node(s) id=4 (not connected, accepting connect from 192.168.1.107) id=5 (not connected, accepting connect from 192.168.1.108) On all the 3 machines mysql-server & client(apt-get install mysql-server mysql-client) were already installed and I completely stopped and also removed them at the system start up. Now the mysqld is from extracted cluster tar ball(/usr/local/mysql/support-files/mysql.server). As for testing, I created a test database on both the data nodes but the tables are also not syncing on other node. I checked many links, configurations are remained similar in all the links but somewhere it's going wrong. Anymore extra package is required?, Could anyone help me here..?. I am trying this for past 3 days... Thank you!

  Read the article

• SeLinux blocking connection to sshd on Ubuntu 9.10

  - by Barton Chittenden

  When I try to log on to my laptop, which runs Ubuntu 9.10, the server rejects my login attempts. Checking /var/log/auth.log, I see the following: Feb 14 12:41:16 tiger-laptop sshd[6798]: error: ssh_selinux_getctxbyname: Failed to get default SELinux security context for tiger I googled for this, and ran across the following: http://www.spinics.net/lists/fedora-.../msg13049.html Here's the part that I think relates to the problem that I'm having: Quote: What's wrong on my system? Why it's not possible to login even if selinux is in permissive mode? Any suggestions? I'd start by trying to figure out why sshd isn't running in sshd_t (it seems to be running in sysadm_t). Paul. selinux mailing list selinux@xxxxxxxxxxxxxxxxxxxxxxx https://admin.fedoraproject.org/mail...stinfo/selinux Yes, sshd is running in sysadm_t: ps axZ | grep sshd system_u:system_r:sysadm_t 3632 ? Ss 0:00 /usr/sbin/sshd -o PidFile=/var/run/sshd.init.pi ls -Z /usr/sbin/sshd system_ubject_r:sshd_exec_t /usr/sbin/sshd Don't know why it's not sshd_t. I didn't modified something. It's a standard installation of sles11 with the default reference policy from tresys. Maybe this code snippet from policy/modules/services/ssh.te is responsible for that: Allow ssh logins as sysadm_r:sysadm_t gen_tunable(ssh_sysadm_login, true) Any ideas? Do you have boolean init_upstart set to on? if not try setting it to on. I do not believe ssh_sysadm_login boolean works currently but i may be mistaken. -- Yeah, setting init_upstart to on did the trick! THANK A LOT! Do you know why this prevents the user from logging in through ssh even if selinux is set to permissive?? Ok, so the million dollar question is "where do I set 'init_upstart=1'"? It's not clear from context which configuration file needs to be edited, and I'm not at all familiar with SELinux configuration.

  Read the article

• package issue with ubuntu 10.10 and passenger requirements

  - by user368937

  I'm trying to get Passenger working with Ubuntu 10.10 and I'm running into a problem. It seems that the passenger installer is not recognizing the virtual package. I'm getting this error: Code: passenger-install-apache2-module ... * OpenSSL support for Ruby... not found ... And then it says, run this: * To install OpenSSL support for Ruby: Please run apt-get install libopenssl-ruby as root. When I run the above command, it refers to the libruby package: sudo apt-get install libopenssl-ruby Reading package lists... Done Building dependency tree Reading state information... Done Note, selecting 'libruby' instead of 'libopenssl-ruby' libruby is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 43 not upgraded. When I look at the details for libruby, it says it provides libopenssl-ruby: Code: Provides: libbigdecimal-ruby, libcurses-ruby, libdbm-ruby, libdl-ruby, libdrb-ruby, liberb-ruby, libgdbm-ruby, libiconv-ruby, libopenssl-ruby, libpty-ruby, libracc-runtime-ruby, libreadline-ruby, librexml-ruby, libsdbm-ruby, libstrscan-ruby, libsyslog-ruby, libtest-unit-ruby, libwebrick-ruby, libxmlrpc-ruby, libyaml-ruby, libzlib-ruby And when I rerun the passenger installer, it gives the same error: Code: passenger-install-apache2-module ... * OpenSSL support for Ruby... not found ... Let me know if you need more info. How do I fix this?

  Read the article

• Where is vmlinux on my Ubuntu installation?

  - by Jason Baker

  I'm trying to work with starting up oprofile, and I'm running into a problem at this step: opcontrol --vmlinux=/path/to/vmlinux Ubuntu has no package called vmlinux, and when I do a locate vmlinux, I get a lot of files: /usr/src/linux-headers-2.6.28-14/arch/h8300/boot/compressed/vmlinux.lds /usr/src/linux-headers-2.6.28-14/arch/m68k/kernel/vmlinux-std.lds /usr/src/linux-headers-2.6.28-14/arch/m68k/kernel/vmlinux-sun3.lds /usr/src/linux-headers-2.6.28-14/arch/mn10300/boot/compressed/vmlinux.lds /usr/src/linux-headers-2.6.28-14/arch/sh/boot/compressed/vmlinux_64.lds /usr/src/linux-headers-2.6.28-14/arch/x86/boot/compressed/vmlinux_32.lds /usr/src/linux-headers-2.6.28-14/arch/x86/boot/compressed/vmlinux_64.lds /usr/src/linux-headers-2.6.28-14/include/asm-generic/vmlinux.lds.h /usr/src/linux-headers-2.6.28-15/arch/h8300/boot/compressed/vmlinux.lds /usr/src/linux-headers-2.6.28-15/arch/m68k/kernel/vmlinux-std.lds /usr/src/linux-headers-2.6.28-15/arch/m68k/kernel/vmlinux-sun3.lds /usr/src/linux-headers-2.6.28-15/arch/mn10300/boot/compressed/vmlinux.lds /usr/src/linux-headers-2.6.28-15/arch/sh/boot/compressed/vmlinux_64.lds /usr/src/linux-headers-2.6.28-15/arch/x86/boot/compressed/vmlinux_32.lds /usr/src/linux-headers-2.6.28-15/arch/x86/boot/compressed/vmlinux_64.lds /usr/src/linux-headers-2.6.28-15/include/asm-generic/vmlinux.lds.h /usr/src/linux-headers-2.6.28-16/arch/h8300/boot/compressed/vmlinux.lds /usr/src/linux-headers-2.6.28-16/arch/m68k/kernel/vmlinux-std.lds /usr/src/linux-headers-2.6.28-16/arch/m68k/kernel/vmlinux-sun3.lds /usr/src/linux-headers-2.6.28-16/arch/mn10300/boot/compressed/vmlinux.lds /usr/src/linux-headers-2.6.28-16/arch/sh/boot/compressed/vmlinux_64.lds /usr/src/linux-headers-2.6.28-16/arch/x86/boot/compressed/vmlinux_32.lds /usr/src/linux-headers-2.6.28-16/arch/x86/boot/compressed/vmlinux_64.lds /usr/src/linux-headers-2.6.28-16/include/asm-generic/vmlinux.lds.h Which one of these is the one I'm looking for?

  Read the article

• How to create VirtualHost in Ubuntu 12.10

  - by Mifas

  I had followed many articles to 'How to create VirtualHost in Ubuntu'. This is what have I done Installed Apache sudo apt-get install lamp-server^ phpmyadmin I created folder called site1.com in /var/www/ Then I have created the file in /etc/apache2/sites-available/site1.com Then added the following code to that site1.com file <VirtualHost *:80> ServerName www.site1.com ServerAdmin [email protected] ServerAlias site1.com DocumentRoot /var/www/site1.com # Other directives here <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/site1.com/> Options Indexes FollowSymLinks MultiViews AllowOverride all Order allow,deny Allow from all </Directory> </VirtualHost> Then after that I edit the host file added the following line of code 127.0.0.1 site1.com Edit Also I enable the site1.com via sudo a2ensite site1.com Then i restart the apache serivice. (Even i restarted the pc) When I go to the site1.com, It will say The connection has timed out Error Message. But I can browse via localhost/site1.com. I have been trying since last two days. No solution. And followed many articles and videos.

  Read the article

• How to wake from screensaver directly to the login screen in Ubuntu

  - by torbengb

  (a.k.a. How to switch users without entering password, part II) (see part I) I've got Ubuntu 9.10 with a user account for my wife, and one for myself. "Wake-from-screensaver" should result in "choose user" without having to enter any password. I know how to do that in Windows, but I'm not good with Linux (yet). Part of this was answered in my earlier question which helped me get past the login screen without passwords (after booting, and after choosing "switch user"), but once the screensaver kicks in and I wake it up again, the system does not present the "choose user" screen. Instead, it either turns off the screensaver and presents the desktop of the most recent user, or (if the screensaver is set to lock the screen) prompt for the user's password (which can be handily surpassed by clicking the "switch user" button and choosing the same user again). So, the login ("choose user") screen has been dealt with. How do I make the (any) screensaver return to the login screen at wake, rather than to the current user's desktop? Windows can do this, I'm sure Linux can too - but how?

  Read the article

• Exporting Environment Variables in Ubuntu Linux

  - by stanigator

  I know many people have asked about environment variables before, but I am having a hard time dealing with these paths while ensuring I don't mess around with the original settings. How would you go about executing these commands in Ubuntu in terms of environment variables? Thanks in advance! Please put /home/stanley/Downloads/ns-allinone-2.34/bin:/home/stanley/Downloads/ns-allinone-2.34/tcl8.4.18/unix:/home/stanley/Downloads/ns-allinone-2.34/tk8.4.18/unix into your PATH environment; so that you'll be able to run itm/tclsh/wish/xgraph. IMPORTANT NOTICES: (1) You MUST put /home/stanley/Downloads/ns-allinone-2.34/otcl-1.13, /home/stanley/Downloads/ns-allinone-2.34/lib, into your LD_LIBRARY_PATH environment variable. If it complains about X libraries, add path to your X libraries into LD_LIBRARY_PATH. If you are using csh, you can set it like: setenv LD_LIBRARY_PATH If you are using sh, you can set it like: export LD_LIBRARY_PATH= (2) You MUST put /home/stanley/Downloads/ns-allinone-2.34/tcl8.4.18/library into your TCL_LIBRARY environmental variable. Otherwise ns/nam will complain during startup.

  Read the article

• ServerName not working in Apache2 and Ubuntu

  - by CreativeNotice

  Setting up a dev LAMP server and I wish to allow dynamic subdomains, aka ted.servername.com, bob.servername.com. Here's my sites-active file <VirtualHost *:80> # Admin Email, Server Name, Aliases ServerAdmin [email protected] ServerName happyslice.net ServerAlias *.happyslice.net # Index file and Document Root DirectoryIndex index.html DocumentRoot /home/sysadmin/public_html/happyslice.net/public # Custom Log file locations LogLevel warn ErrorLog /home/sysadmin/public_html/happyslice.net/log/error.log CustomLog /home/sysadmin/public_html/happyslice.net/log/access.log combined And here's the output from sudo apache2ctl -S VirtualHost configuration: wildcard NameVirtualHosts and default servers: *:80 is a NameVirtualHost default server happyslice.net (/etc/apache2/sites-enabled/000-default:1) port 80 namevhost happyslice.net (/etc/apache2/sites-enabled/000-default:1) port 80 namevhost happyslice.net (/etc/apache2/sites-enabled/happyslice.net:5) Syntax OK The server hostname is srv.happyslice.net. As you can see from apache2ctl when I use happyslice.net I get the default virtual host, when I use a subdomain, I get the happyslice.net host. So the later is working how I want, but the main url does not. I've tried all kinds of variations here, but it appears that ServerName just isn't being tied to the correct location. Thoughts? I'm stumped. FYI, I'm running Apache2.1 and Ubuntu 10.04 LTS

  Read the article

• Installing mod_mono on Ubuntu: handler doesn't seem to get registered

  - by Trevor Johns

  I'm trying to install mod_mono on Apache 2 (Prefork MPM). I'm using Ubuntu Karmic, and just want an auto-hosting setup (so that any .aspx files are executed, similar to how PHP is normally setup). I did the following to install Mono: $ apt-get install libapache2-mod-mono mono-apache-server2 mono-devel $ a2dismod mod_mono $ a2enmod mod_mono_auto I've confirmed that mod_mono is getting loaded by Apache. However, any .aspx pages I try to load are returned unprocessed and still have an application/x-asp-net MIME type. It's as if the mod_mono handler never gets registered with Apache. Here's the contents of /etc/mod_mono_auto.load: LoadModule mono_module /usr/lib/apache2/modules/mod_mono.so And here's /etc/mod_mono_auto.conf: MonoAutoApplication enabled AddType application/x-asp-net .aspx AddType application/x-asp-net .asmx AddType application/x-asp-net .ashx AddType application/x-asp-net .asax AddType application/x-asp-net .ascx AddType application/x-asp-net .soap AddType application/x-asp-net .rem AddType application/x-asp-net .axd AddType application/x-asp-net .cs AddType application/x-asp-net .config AddType application/x-asp-net .dll DirectoryIndex index.aspx DirectoryIndex Default.aspx DirectoryIndex default.aspx I've even tried setting the handler explicitly: AddHandler mono .aspx .ascx .asax .ashx .config .cs .asmx .asp Nothing seems to help. Any ideas how to get this working?

  Read the article

• Joining an Ubuntu 14.04 machine to active directory with realm and sssd

  - by tubaguy50035

  I've tried following this guide to set up realmd and sssd with active directory: http://funwithlinux.net/2014/04/join-ubuntu-14-04-to-active-directory-domain-using-realmd/ When I run the command realm –verbose join domain.company.com –user-principal=c-u14-dev1/[email protected] –unattended everything seems to connect. My sssd.conf looks like the following: [nss] filter_groups = root filter_users = root reconnection_retries = 3 [pam] reconnection_retries = 3 [sssd] domains = DOMAIN.COMPANY.COM config_file_version = 2 services = nss, pam [domain/DOMAIN.COMPANY.COM] ad_domain = DOMAIN.COMPANY.COM krb5_realm = DOMAIN.COMPANY.COM realmd_tags = manages-system joined-with-adcli cache_credentials = True id_provider = ad krb5_store_password_if_offline = True default_shell = /bin/bash ldap_id_mapping = True use_fully_qualified_names = True fallback_homedir = /home/%d/%u access_provider = ad My /etc/pam.d/common-auth looks like this: auth [success=3 default=ignore] pam_krb5.so minimum_uid=1000 auth [success=2 default=ignore] pam_unix.so nullok_secure try_first_pass auth [success=1 default=ignore] pam_sss.so use_first_pass # here's the fallback if no module succeeds auth requisite pam_deny.so # prime the stack with a positive return value if there isn't one already; # this avoids us returning an error just because nothing sets a success code # since the modules above will each just jump around auth required pam_permit.so # and here are more per-package modules (the "Additional" block) auth optional pam_cap.so However, when I try to SSH into the machine with my active directory user, I see the following in auth.log: Aug 21 10:35:59 c-u14-dev1 sshd[11285]: Invalid user nwalke from myip Aug 21 10:35:59 c-u14-dev1 sshd[11285]: input_userauth_request: invalid user nwalke [preauth] Aug 21 10:36:10 c-u14-dev1 sshd[11285]: pam_krb5(sshd:auth): authentication failure; logname=nwalke uid=0 euid=0 tty=ssh ruser= rhost=myiphostname Aug 21 10:36:10 c-u14-dev1 sshd[11285]: pam_unix(sshd:auth): check pass; user unknown Aug 21 10:36:10 c-u14-dev1 sshd[11285]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=myiphostname Aug 21 10:36:10 c-u14-dev1 sshd[11285]: pam_sss(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=myiphostname user=nwalke Aug 21 10:36:10 c-u14-dev1 sshd[11285]: pam_sss(sshd:auth): received for user nwalke: 10 (User not known to the underlying authentication module) Aug 21 10:36:12 c-u14-dev1 sshd[11285]: Failed password for invalid user nwalke from myip port 34455 ssh2 What do I need to do to allow active directory users the ability to log in?

  Read the article

• With Ubuntu 9.10, my DVD keeps spinning up

  - by Ken

  I have Ubuntu 9.10 on my Intel Mac Mini. When there's a DVD in the drive, and even if there's no program open at all (just looking at the desktop), every minute or so the disc spins up with a loud whirring noise, and I can hear it cranking the motor to seek across the disc. How do I find out what's causing this? And how can I make it stop? Thanks! EDIT: I straced nautilus, and saw nothing it's doing directly, even when the disc spins up. It does poll inotify regularly, but I don't know how to trace what it's watching, or if that's even how it receives disc-inserted notifications. It doesn't call inotify_add_watch when I insert a disc or mount it (or eject or umount), but it could be watching all of /dev already or something like that. Of course, a DVD is mounted read-only, so whether it's inotify or something else, it should never need to poll anything on that. And if it is inotify, it's happening in the kernel, and the kernel should really never need to poll a device it's mounted to check for notifications.

  Read the article

• Running Jackd on Ubuntu for my External Firewire Sound card

  - by Asaf

  Hello, I'm running Ubuntu 10.04 and I have an external Sound card: Phonic Firefly 302. I've connected the device, installed Jackd, added the lines: @audio - rtprio 99 @audio - memlock 500000 @audio - nice -10 to /etc/security/limits.conf logged out, logged back in, ran qjackctl (sudo qjackctl to be exact), ran the settings and chose "firewire" on the driver option, pressed "Start" and that was the output: 20:10:19.450 Patchbay deactivated. 20:10:19.578 Statistics reset. 20:10:19.601 ALSA connection graph change. 20:10:19.828 ALSA connection change. 20:10:21.293 Startup script... 20:10:21.293 artsshell -q terminate sh: artsshell: not found 20:10:21.695 Startup script terminated with exit status=32512. 20:10:21.695 JACK is starting... 20:10:21.695 /usr/bin/jackd -dfirewire -r44100 -p1024 -n3 jackd 0.118.0 Copyright 2001-2009 Paul Davis, Stephane Letz, Jack O'Quinn, Torben Hohn and others. jackd comes with ABSOLUTELY NO WARRANTY This is free software, and you are welcome to redistribute it under certain conditions; see the file COPYING for details 20:10:21.704 JACK was started with PID=22176. no message buffer overruns JACK compiled with System V SHM support. loading driver .. libffado 2.0.0 built Mar 31 2010 14:47:42 firewire ERR: Error creating FFADO streaming device cannot load driver module firewire no message buffer overruns 20:10:21.819 JACK was stopped successfully. 20:10:21.819 Post-shutdown script... 20:10:21.822 killall jackd jackd: no process found 20:10:22.230 Post-shutdown script terminated with exit status=256. 20:10:23.865 Could not connect to JACK server as client. - Overall operation failed. - Unable to connect to server. Please check the messages window for more info. Error: "/tmp/kde-asaf" is owned by uid 1000 instead of uid 0.

  Read the article

• Ubuntu 10.04 server delay responding to AJAX requests

  - by DanielAttard

  I manage a Ubuntu 10.04 server with a couple of domains hosted on it. As I continue to learn more about all these wonderful new (for me), one issue that I have begun to notice is the delay it sometimes takes for the server to respond to certain requests. As an example, when I view the timeline of events using firebug I can see that most of the time when I make a POST, the server responds in under 100ms. Sometimes, however, there is a substantial delay before the RESPONSE from the server. I can't seem to tell when the delay will happen and when it won't, however, when it happens the delay is always for about 4.5 seconds. The delay seems to happen about 30-40% of the time. Here is the section of apache2.conf dealing with logs: # # The following directives define some format nicknames for use with # a CustomLog directive (see below). # If you are behind a reverse proxy, you might want to change %h into %{X-Forwarded-For}i # LogFormat "%v:%p %h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" vhost_combined LogFormat "%h %l %u %t \"%r\" %>s %O \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %O" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent I have no idea where to look to try and debug this problem or investigate further. Any suggestions?

  Read the article

• Ubuntu 12.04 compiz - disable all compiz plugin - empty screen

  - by gotqn

  A lots of thanks to terdon who spent so many time on this and finally solve the issue. A friend of mine has installed on my new machine Ubuntu 12.04 (I have always been windows user and have no experience with Linux). I started to watch some tutorial about how to make 'Rotated Cube' using 'Compiz',but the cube appears in the form of a list (only two slides). I have thought this could be result of my video cards (only two - one from the processor and one from the motherboard) and they can not support this options. Anyway, I have decided to disable all compiz plugins and options because my friend has set some, and I started to think there is some misunderstanding between the plugins. After, that I got only empty screen(no menu, no icons, anything) and can do nothing. How to fix this? EDIT: When I remove the compiz stuffs (from the console), the menu is shown again. Then I install the compiz again (some of the effect are still not working). After restart or log out/in the menu is hidden again. I suppose that there are some settings that I've broken but they are saved somewhere in the system and remove the compiz do not deleted them and as a result they are activated after compiz is installed again and the PC is restarted?

  Read the article

• Unable to install mysql-server in Ubuntu

  - by Arihant

  I am unable to install mysql-server on my ubuntu 9.10 server machine. When using apt-get install mysql-server the output is : # apt-get install mysql-server Reading package lists... Done Building dependency tree Reading state information... Done mysql-server is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 120 not upgraded. 2 not fully installed or removed. After this operation, 0B of additional disk space will be used. Setting up mysql-server-5.1 (5.1.37-1ubuntu5.4) ... * Stopping MySQL database server Mysqld [ OK ] * Starting MySQL database server mysqld [fail] invoke-rc.d: initscript mysql, action "start" failed. dpkg: error processing mysql-server-5.1 (--configure): subprocess installed post-installation script returned error exit status 1 dpkg: dependency problems prevent configuration of mysql-server: mysql-server depends on mysql-server-5.1; however: Package mysql-server-5.1 is not configured yet. dpkg: error processing mysql-server (--configure): dependency problems - leaving unconfigured No apport report written because the error message indicates its a followup error from a previous failure. Errors were encountered while processing: mysql-server-5.1 mysql-server E: Sub-process /usr/bin/dpkg returned an error code (1) I cant find a satisfactory solution to this problem anywhere. Many sites tell to reinstall it but its not working. Any help will be appreciated. Thank you..

  Read the article

• Nexus One Android Debugging in Ubuntu 9.10

  - by Doughy

  I can't get Ubuntu 9.10 to recognize the Nexus One as a debug device. I tried following the instructions found here but they are not working: http://alan.lamielle.net/2010/01/22/nexus-one-usb-in-ubuntu-9-10 Anyone know of a link or know how to get the Nexus One to debug correctly in Ubuntu 9.10?

  Read the article

• Can't mount FAT32 drive under Ubuntu Linux

  - by Josh

  I have a 320GB USB drive with a single large FAT32 partition. The volume mounts perfectly fine on my Mac OS X 10.5.8 machine and Disk Utility on the mac reports no issues with the volume. I can read/write all data on the drive. However when I connect the drive to my Ubuntu 9.10 Karmic system, the partition does not mount. dmesg|tail says: [ 2752.334822] scsi3 : SCSI emulation for USB Mass Storage devices [ 2752.335040] usb-storage: device found at 3 [ 2752.335044] usb-storage: waiting for device to settle before scanning [ 2757.330301] usb-storage: device scan complete [ 2757.331005] scsi 3:0:0:0: Direct-Access WD 3200AAK External 1.65 PQ: 0 ANSI: 0 [ 2757.331772] sd 3:0:0:0: Attached scsi generic sg2 type 0 [ 2757.355647] sd 3:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB) [ 2757.360737] sd 3:0:0:0: [sdb] Write Protect is off [ 2757.360749] sd 3:0:0:0: [sdb] Mode Sense: 00 00 00 00 [ 2757.360755] sd 3:0:0:0: [sdb] Assuming drive cache: write through [ 2757.367618] sd 3:0:0:0: [sdb] Assuming drive cache: write through [ 2757.367631] sdb: sdb1 [ 2762.797622] sd 3:0:0:0: [sdb] Assuming drive cache: write through [ 2762.797636] sd 3:0:0:0: [sdb] Attached SCSI disk [ 2822.866228] FAT: bogus number of reserved sectors [ 2822.866237] VFS: Can't find a valid FAT filesystem on dev sdb1. When I run fsck.vfat -a /dev/sdb1 I get: root@cartman:~# fsck.vfat -a /dev/sdb1 dosfsck 3.0.3, 18 May 2009, FAT32, LFN Logical sector size is zero. Googling "vfat Logical sector size is zero" produced no consensus as to the solution. I would prefer not to have to completely reformat the disk if possible because it contains about 280GB of data I would rather not have to find a temporary home for. Any suggestions?

  Read the article

• Conky starts above windows in Ubuntu Maverick

  - by DesertIvy

  Hey guys, I did not run into this problem until I upgraded my Ubuntu box to Maverick Meerkat (10.10). Basically, whenever I start my computer, conky runs as expected, except it gets drawn over any windows that I load (see screenshot). To fix this for a single session, I simply restart conky by running killall conky; conky in a terminal. Conky gets re-drawn below active windows (namely, only appearing on my desktop), and does not have the border/drop-shadow, but I have to do this every time I start a new session. Is there a simple way to fix this? I have a small shell script that I run on startup, but it does not seem to solve the problem. #!/bin/bash sleep 10 && conky; sleep 5 && killall conky; conky; Below is the non-text part of my .conkyrc file. # Conky settings # background yes update_interval 1 cpu_avg_samples 2 net_avg_samples 2 override_utf8_locale yes double_buffer yes no_buffers yes text_buffer_size 2048 #imlib_cache_size 0 temperature_unit fahrenheit # Window specifications # own_window yes own_window_type override own_window_transparent yes own_window_hints undecorate,sticky,skip_taskbar,skip_pager,below border_inner_margin 0 border_outer_margin 0 minimum_size 200 250 maximum_width 200 alignment tr gap_x 220 gap_y 280 # Graphics settings # draw_shades no draw_outline no draw_borders no draw_graph_borders no # Text settings # use_xft yes xftfont caviar dreams:size=8 xftalpha 0.5 uppercase no temperature_unit celsius default_color FFFFFF # Lua Load # lua_load ~/.lua/scripts/clock_rings.lua lua_draw_hook_pre clock_rings

  Read the article

• ubuntu - Best way of repartitioning a (running) production server

  - by egarcia

  I've got an (externally hosted) production server running Ubuntu LTS. It serves webpages (rails) and has an svn repository accesible through Apache, and a PostgreSQL db. I've got ssh access to the server and root privileges. Most of the "interesting" stuff is located in /var/ : svn repositories are inside /var/svn, web pages under /var/www, etc. Yesterday I was curious about how much disk space had it left, so I did the following: $ df -h Filesystem Size Used Avail Use% Mounted on /dev/md1 950M 402M 500M 45% / varrun 990M 64K 990M 1% /var/run varlock 990M 0 990M 0% /var/lock udev 990M 76K 989M 1% /dev devshm 990M 0 990M 0% /dev/shm /dev/md5 4.7G 668M 4.1G 15% /usr /dev/md6 4.7G 1.4G 3.4G 29% /var /dev/md7 221G 28M 221G 1% /home none 990M 4.0K 990M 1% /tmp My 'var' partition, which holds most of the interesting part, is only 4.7G big. The /home/ partition, on the other hand, is 221G, but it is mostly unused. I should have checked the disk layout before starting installing stuff. Ideally I would need /var/ and /home/ to be "switched" - /home/ should be the one with 4.7G, and /var/ the one with 221G. Is there a way to solve this without having to reinstall the whole thing?

  Read the article

• How have I locked me out from my Ubuntu VPS?

  - by Sanoj

  I have a Ubuntu Server as VPS (OpenVZ), and yesterday I installed php-fpm, but I guess something went wrong with the installation. Because since then I cannot log in to my server over SSH with PuTTY or using WinSCP. The message I get when connecting is Network error: Connection timed out. Immediately after the installation I was not able to use emacs either, I had to re-install it with apt-get install emacs. I have tried with clearing the firewall and rebooting the server from my web-based "control panel", but it doesn't help. The commands I used for installation of the PHP-fpm was from Installing PHP 5.3, Nginx And PHP-fpm On Ubuntu/Debian. And I guess it has something to do with these commands: cd /tmp wget http://us.archive.ubuntu.com/ubuntu/pool/main/k/krb5/libkrb53_1.6.dfsg.4~beta1-5ubuntu2_i386.deb wget http://us.archive.ubuntu.com/ubuntu/pool/main/i/icu/libicu38_3.8-6ubuntu0.2_i386.deb sudo dpkg -i *.deb sudo echo "deb http://php53.dotdeb.org stable all" >> /etc/apt/sources.list sudo apt-get update sudo apt-get install php5-cli php5-common php5-suhosin sudo apt-get install php5-fpm php5-cgi The web-sites that are hosted from my server works fine. Anyone that have the same experience or know how this could happen? I guess that I have to re-install Ubuntu Server from my "control panel" now, but I would like to avoid this situation in the future. Finally, I have backup on everything so nothing is lost if I have to re-install the machine.

  Read the article

• Using AT on Ubuntu to Background Downloads (w/ Queue)

  - by Nicholas Yost

  I am writing a PHP script, but I want to use the AT command in Ubuntu to fetch a remote file via WGET. I'm basically looking to background the process, so PHP can finish fairly quickly. I cannot find any questions on here about how to use both, but I basically want to do the following pseudo-code: <?php exec('at now -q queuename wget http://path.to/remote/file.ext'); ?> Additionally, I'd like to queue this between providers. I'd like to have each path.to have its own queue, so I only download one file from each provider at a time. Meaning: <?php exec('at now -q remote wget http://path.to/remote/file.ext /local/path'); exec('at now -q vendorone wget http://vendor.one/remote/file.ext /local/path'); exec('at now -q vendortwo wget http://vendor.two/remote/file.ext /local/path'); exec('at now -q vendorone wget http://vendor.one/remote/file.ext /local/path'); ?> This should download the files from path.to, vendor.one, vendor.two immediately, and when the first file is finished downloading from vendor.one, it starts the second file. Does that make sense? I can't find anything like this anywhere on the web, much less on SO/SF. If we can use the crontab to run a one-off wget command, thats fine too.

  Read the article

• Ubuntu Device-mapper seems to be invincible!

  - by Andrew Bolster

  I'm working on a hopefully unrelated question question and I've got to a strange situation. First: I know very little about the very low level hardware kernal storage driver magix, so I'm hoping a) someone can help and b) someone can explain it to me better. I've been trying a dozen different configurations of my 2x500GB SATA drives over the past few hours involving switching between ACHI/IDE/RAID in my bios; After each attempt I've reset the bios option, booted into a live CD, deleting partitions and rewriting partition tables left on the drives. Now, however, I've been sitting with a /dev/mapper/nvidia_XXXXXXX1 that seems to be impossible to kill! its the only 'partition' that i see in the Ubuntu install (but I can see the others in parted) but it is only the size of one of the drives, and I know I did not set any RAID levels other than RAID0. Anyone have any ideas how I can kill this and get back to just two independent IDE drives? Or can anyone convince me of a reason to go the AHCI route? Many thanks in advance.

  Read the article

• really weird DNS problem in Ubuntu {after one month, seems like ISP problem}

  - by OmniWired

  Hello everyone. I been having this random dns problem, in Ubuntu 10.04 and in 10.10 it started about 2 weeks ago after (I believe) an update. Basically when I go to a website randomly I get that the website I'm visiting is not available ("Oops! Google Chrome could not connect to ..." & "This webpage is not available."). I tested with Chromium "7.0.515.0 (58587)" and Firefox minefield (4.0ish) and 3.6.9. I did these 4 things already: /etc/default/grub GRUB_CMDLINE_LINUX="ipv6.disable=1" and this: /etc/sysctl.conf net.ipv6.conf.all.disable_ipv6 = 1 net.ipv6.conf.default.disable_ipv6 = 1 net.ipv6.conf.lo.disable_ipv6 = 1 *disabling Chromium DNS pre-fetching *using Google and OpenDNS servers as well as ISP DNS servers. But didn't improve, also no other computers in my network have the same problem. All computer wired to the same router. I'm a software engineer that run out of ideas, please help me. Thanks in advance. UPDATE: some programs (synaptic / firefox update/ vuze(azureus)) say connection refused for the error. Most of the time a second try will fix the "refusal". UPDATE2: I found out with Wireshark, that everytime I have this problem i've got this 192.168.0.10 8.8.8.8 ICMP Destination unreachable (Port unreachable) Confirmed an ISP error. ISP;Speedy Location: Argentina, Buenos Aires (capital Federal) Area.

  Read the article

< Previous Page | 101 102 103 104 105 106 107 108 109 110 111 112  | Next Page >