Search Results

Search found 13434 results on 538 pages for 'boot on power up'.

Page 106/538 | < Previous Page | 102 103 104 105 106 107 108 109 110 111 112 113  | Next Page >

• Debian software raid 1: boot from both disk

  - by bsreekanth

  I newly installed debian squeeze with software raid.The way I did was, as also given in this thread. I have 2 HDD with 500 GB each. For each of them, I created 3 partitions (/boot, / and swap) I selected the hard drive and created a new partition table I created a new partition that was 1GB. I then specified to use the partition as a Physical Volume for RAID. and used for /boot and enabled bootable. Created another partition, which is of 480 GB, and then specified to use the partition as a Physical Volume for RAID. and used for /. Created another partion and used for swap Then RAID configuration: Through Configure RAID menu - create MD device - (2 for the number of drives, 0 for spare devices) Next select the partitions you want to be members of /dev/MD0. I selected /dev/sda1 and /dev/sdb1 (for /boot) Next select the partitions you want to be members of /dev/MD1. I selected /dev/sda6 and /dev/sdb6 (for /) And no RAID for swap partitions 'Finish Partitioning and write changes to disk' -- Finish the rest of the install like normal Everything is ok now, except I am not sure how to test my raid config. When I pull the power of the HDD, it only boots from one disk. I read in some forum that I may have to install GRUB manually on the other. In Debian Squeeze, there is no grub command. Not sure how to make my software raid bootable from both disk. Also, please comment on my steps above. Anything unusual. I configured /boot partitions of both disks to be boot=yes. Not sure whether that is ok. Thanks, Bsr

  Read the article

• network boot options hosted on windows (xp or 7)

  - by Crash893

  I'm looking to setup a quick and dirty network boot server to install xp on a beatup laptop that has a bad cdrom but the option to "network boot" (compaq pasario 700) 1) what is the diffrence between pxe and Ris 2) which one is most likely to be the one used on the laptop mentioned above 3) is there a windows program to run a boot server 4) what files will i need to have can i jut use the cd or do i need to rip it to files or and iso? thanks Rob

  Read the article

• Boot camp with Vista crashes on startup

  - by Mark Pim

  I have a 2006 vintage MacBook Pro (Intel Core 2 Duo) and have been using Boot Camp since it was in beta. I had been running XP SP2 on it with Tiger quite happily. I've recently wiped and reinstalled everything to upgrade to Leopard. After installing Leopard, I fired up the Boot camp assistant and used it to install the Windows 7 RC. That worked really nicely, but my HFS+ driver didn't work under Windows 7 yet so I decided to install Vista instead. I didn't repartition the drive, just launched the Vista installation disk from BIOS and told it to overwrite the existing Windows 7 install. It installed fine and I installed the Boot Camp drivers, still all fine. Now, however, every time I boot into Windows and login it hard reboots itself as the desktop is appearing. After this it works fine again. Until the next power off. Has anyone had any similar problems? Or can offer suggestions on how to solve this?

  Read the article

• Boot Camp fails to create a Windows partition because it can't move files

  - by Jens Bannmann

  I'm running Mac OS X 10.6 (Snow Leopard) on a mac with a 320 GB drive, 167GB free space, and I can't get Boot Camp running. The wizard starts creating the Windows partition, but fails with a message claiming it cannot move some files. The message suggests to back up my hard disk, reformat it, restore my files, and re-run Boot Camp wizard. The problem is: Though I do have backups (Time Machine), I don't feel like formatting my hard disk right now :-) I found a thread in some forum discussing this problem. The suggestion was to defragment my volume with iDefrag, and lots of people claimed that solved the issue. So I went ahead and got iDefrag 1.7.1, created a bootable DVD and chose the "compact" setting recommended before partitioning - but still no luck with Boot Camp! So how do I get this working? Fun note: last year, I briefly set up Boot Camp with 10.5, and it worked perfectly. Probably I did not use that much hard disk space back then...

  Read the article

• Boot from USB at booting time win Windows 7

  - by MA1

  Hello Everyone hope you will be fine and good. 1) I need a tool/software that i can run from USB at boot time 2) How to boot the USB at booting time 3) and...how to run that progam/tool/software Actually, what i want to do is to copy some files from hardisk to USB at boot. Can anyone help...or point me to some useful link/book etc... Thanks.

  Read the article

• IBM x260m won't boot from PCI SATA card

  - by syrenity

  Hi. We ghosted our old Windows 2003 drive to a new 1TB one, and connected through new PCI SATA card. The x260m server fails to boot with error 1962: "Boot sector not found." When we connect the drive directly to motherboard, it boots fine, so the problem is probably in getting BIOS to boot from the SATA card. Has anyone encountered and solved such issue? EDIT: We tried disabling the on-board Sata controller (Hostraid/SAS?), but there is no such option - only enable, enhanced and compatible. Tried also to chance boot device priority to all possible choices - no luck. Thanks in advance!

  Read the article

• Ubuntu 8.10 and Ubuntu 9.10 in dual boot ?

  - by Arkapravo

  Hi Is it possible to have Ubuntu 8.10 as second (or third) boot with Ubuntu 9.10 as first boot ? I have not been able to get it to work, may be issues with Grub. PS : Don't ask me why I want this sort of dual boot, long story !

  Read the article

• Converting software RAID1 to RAID10 for /boot

  - by luckytaxi

  Array info: /dev/md0 - /dev/sda1 and /dev/sdb1 /dev/md2 - /dev/sda2 and /dev/sdb2 Partition info: /boot - /dev/md0 / - /dev/md1 I have two drives that are setup as RAID1 using software RAID on Redhat. I added two additional drives (same size) and I would like to conver the RAID1 to a RAID10. The problem I'm having is adding the last drive to the array. I've gotten as far as creating a RAID10 with two missing devices but as soon as I add the last drive, all hell breaks loose. It seems /dev/sda1 is the culprit. What I'm not too sure about is how to create the RAID10. I've tried the following mdadm --create /dev/md2 --level=raid10 --raid-device=4 /dev/sdc1 missing /dev/sdd1 missing I then proceeded to fail /dev/sdb1 from /dev/md0 and added that partition to /dev/md2. I proceeded to install the MBR on EACH partition since boot resides on /dev/sdx1 on each drive. As a test, all is well, I'm able to boot back into the system once I do a quick reboot. Now, when I go add the last drive /dev/sda1, it breaks. I attempted to install grub on /dev/sda1 and I get the following ... grub> root (hd0,0) /dev/sda root (hd0,0) /dev/sda Filesystem type is ext2fs, partition type 0xfd grub> setup (hd0) setup (hd0) Checking if "/boot/grub/stage1" exists... no Checking if "/grub/stage1" exists... no Error 2: Bad file or directory type At this point, the array is hosed I believe. I rebooted the server and it refuses to boot.

  Read the article

• Windows External Harddisk drive letter after cloning boot partition to it

  - by gladiator2345

  I cloned my windows 7 installation on c: to external hard drive. I applied usb patch using pwboot and i could successfully boot into windows. But My problem is even though i am booting in to external hd the file reference and system path is pointing to c: on my internal hard disk. If i remove internal hd and boot it will get stuck at login screen. Is there any way i can force drive letter c: to my boot partition on external hd while booting from it.

  Read the article

• WDS - Clients receive Error: PXE-E53: No boot filename received

  - by Ninja2k

  I have setup WDS on Windows 2008 server in a Vmware box so I can practise setting up WDS,the server has DNS and DHCP as well as AD, the boot image is confirmed as working but when my clients try to boot up it does not work. I have checked the following: Clients can ping the WDS server. The WDS service is started Boot images for X86 and X64 are deployed. HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\WDSServer\Providers\WDSPXE UseDhcpPorts has been set to 0 My clients just receive Error: PXE-E53: No boot filename received. Any idea what could be wrong?

  Read the article

• Arch Linux: eth0 no carrier - network fails at boot

  - by user905686

  The problem My computer is connected to a network where dhcp is required. So my network configuration in /etc/rc.conf looks like interface=eth0 address= netmask= broadcast= gateway= My deamons are DAEMONS=(!hwclock syslog-ng network netfs crond ntpd) With this configuration, Arch hangs at boot a long time at "Network" (Still it says "[done]", but after boot I have no connection). I found out two workaround: Workaround 1 remove network from deamons run mii-tool --reset eth0 and dhcpcd eth0 after boot (somehow it does not work when placing these commands in /etc/rc.local. Then dhcp work very quickly (because of the reset!). Before executing the first command, ip link show eth0 has "NO CARRIER" in output. Afterwards, it doesn´t. (Also, mii-tool first shows "no link", afterwards eth0: 10 Mbit, half duplex, link ok. Workaround 2 Change network configuration to interface=eth0 address=x.y.z.21 netmask=255.255.255.0 broadcast=xxx.y.z.255 gateway=x.y.z.254 whereas x, y, z build the specific adresses of the network (Though dhcp is used, I get a static ip). Add the commands mii-tool --reset eth0 and dhcpcd eth0 to /etc/rc.local Now network starts quickly at boot (though I don´t know if successfully), the commands in /etc/rc.local are executed and the connection is fine after login. What to do? So the problem seems to be that dhcpcd stucks at "wating for carrier" or sth. I do not like the workaround, because some deamons need network (though they seem to start). What can I do to have eth0 ready for dhcp at boot? Or is there another problem?

  Read the article

• Windows 7 ignores F6/F8 and will not boot

  - by P.Brian.Mackey

  I have a work PC with sophos safeguard encryption on it. Windows failed to start. When I bootup I receive an error saying a recent hardware or software change might be the cause. File: \Boot\BCD Status: 0xc0000098 Info: The windows boot configuration data file does not contain a valid OS entry. This began after the PC forced me to run a system recovery. My machine had powered down improperly (power outage?) and simply would not respond to my keyboard input to cancel the option to scan my system. After the scan "repaired" a boot file, my system crashed. Now it tells me I can insert my windows 7 disk and run recovery. I can't simply do this because of Safeguard. The system recovery can't see my encrypted drive. I tried hitting F2 to manually login to Safeguard and then selected the option to boot from media. The computer prompts me to hit any key to boot from disk...which I do, but once again it is not reading my keyboard input. I can't get F8/F6 to bypass startup files and get me to a command prompt like the old days. If I could get to a command prompt I might could recover the file windows jacked up from its backup location...though I may need to use the windows recovery disk UI to do this..??? In the past I've been able to slap in a PS/2 keyboard when the USB keyboards stop responding like this. I have no PS/2 keyboard available. Anyone have any idea how I can undo the damage windows system recovery has done with safeguard installed?

  Read the article

• boot failure trying to install linux distro from a cd

  - by jdamae

  Hoping someone can help me get this installation from a cd going. I'm using an older pc: hp pavillion 2.66Ghz, 512RAM with a BIOS revision of 6/30/2003. I reclaimed some an older drive (Seagate ST340810A) that seems to be working as its recognized in the bios (auto-detected) I downloaded a mini.iso of ubuntu 10.10 that I want to install and burned the image to a CD for install. My boot sequence is: First Boot Device [CDROM] and I disabled devices 2-4 so I can just force it to read first from the CDROM. This old pc also has a separate CD writer which is a Sec.Slave, so the Sec.Master is the Toshiba DVD/ROM DSM-171 drive where I placed the burned cd with the linux distro. So, with these settings I cannot get it to boot. I get the "DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER". Where do I go from here? Thanks.

  Read the article

• AHCI, Windows 7 and can only boot with Windows DVD present

  - by Rob Pridham

  Foolishly, I installed Windows 7 with my new SSD set to IDE. I would like to change it to AHCI. I have done this before, with a different motherboard. What happens: I set the controller to AHCI in the BIOS; I also check correct boot order On boot, I get the 'BOOTMGR not found' error I use the Windows Recovery Console on the DVD Diskpart etc can see the disks, and bootrec claims to have rewritten the MBR/bootloader I reboot, same problem Recovery Console again and it detects a problem, fixes, reboots Recovery Console again and it detects the OS, and a problem - fixes, reboots I ignore the 'press any key to boot from DVD' prompt Windows boots fine I restart without the DVD and I'm back to square one That optional 'press a key to boot from DVD' stage is something that the recovery process introduces - normally you have to choose to boot to the DVD at the BIOS stage. You also see this when installing Windows. I suspect that whatever temporary state that is is compatible with AHCI - but not the standard it returns to. I have done the msahci/iaStorV registry hacks to no avail (this worked with the previous board). I can put it back to IDE where normal service is resumed. The board is an Asus M5A99X, the southbridge is AMD SB950, and this is Windows 7 x64. I would quite like not to have to reinstall it again. Any ideas as to what I can do as a permanent fix?

  Read the article

• Can't boot from CD

  - by Jason Swett

  I installed Ubuntu on a PowerBook G4 and it only works about 10% of the time. For this reason I decided to re-install OS X, but my machine won't boot from CD. It also won't boot Ubuntu the vast majority of the time, so I'm kind of screwed. After a ton of tries, I finally got my machine to boot a Linux command line. Is there anything I can do at this point to make my machine more runnable, just for the sake of installing OS X?

  Read the article

• Can't boot from CD

  - by Jason Swett

  I installed Ubuntu on a PowerBook G4 and it only works about 10% of the time. For this reason I decided to re-install OS X, but my machine won't boot from CD. It also won't boot Ubuntu the vast majority of the time, so I'm kind of screwed. After a ton of tries, I finally got my machine to boot a Linux command line. Is there anything I can do at this point to make my machine more runnable, just for the sake of installing OS X?

  Read the article

• Can't install Ubuntu 12 into VirtualBox (USB not recognized, ISO would not boot)

  - by wvxvw

  I'm trying out VirtualBox 4.18 and wanted to install Ubuntu 12 as a test. After installing VirtualBox (on Debian squeeze/sid), creating a virtual machine for Ubuntu and pointing it in Settings Storage IDE Controllers to the ISO with the proper version of Ubuntu, checked the "Live CD" option. Tried to define the IDE as master / slave, primary / secondary - all to no effect, and trying to boot this system, I'm getting to the screen which says: FATAL: could not read from the boot medium! System halted I've copied the same ISO to the USB stick, and I can boot from the USB (outside VirtualBox). I've looked at couple of tutorials / walk-through, there's nothing I can see that I would've done wrong. So, how would I configure it to boot from the desired ISO? Below is the snapshot with the current settings (sorry, I don't know how to get them as text).

  Read the article

• Raid system fails to boot after moving from 2.6 kernel to 3.5

  - by user846226

  I'm running Gentoo Linux with a custom compiled kernel and I've just migrated from a 2.6 kernel to a 3.5. As my HD's are on RAID 0 mode I use a custom initrd file in order to be able to boot. While kernel 2.6 is able to boot without problems the new 3.5 compiled kernel fails to boot complaining about no block devices found. After taking a look at initrd.cpio contained scripts I can see the failure message is given by mdadm tool. Does anyone has a clue about that? Edit: this morning i noticed there was some kind of issue on my old initrd which works fine for 2.6 kernels, so created a new initrd which works fine and let me to boot into GNU/Gentoo Linux with same 3.5 bzImage. It could be an issue of mdadm, gonna check it. https://bugs.gentoo.org/show_bug.cgi?id=416081

  Read the article

• different amazon image with/without ebs boot?

  - by user41999

  i'm at http://alestic.com/ and can see Ubuntu 10.04 Lucid Canonical, ubuntu@ Ubuntu 10.04 Lucid Canonical, ubuntu@EBS boot 1.what is the different between with/without EBS boot? any article explaining this? 2. can provide advantage/disadvantages of using not using ebs boot?

  Read the article

• A problem in my windows boot menu

  - by user210332

  Hi, One i had kept a supervisor password to my windows boot screen, but now i forgot that password, Now i am unable to access the boot menu since its asking the password, all menu options are disabled. Is it possible to remove that password and can i get the boot menu default settings back? Processor: Intel Pentium dual core (2) OS : XP Thanks in Advance,

  Read the article

• Windows 7 Boot Loader - Remove 30 second waiting time

  - by derekhh

  I've installed Fedora 17 and Windows 7 on two different hard disks as a dual-boot system. The default boot loader is GRUB 2 maintained and configured in Fedora 17. When I startup and choose "Windows 7 bootloader (on /dev/sda1)" in GRUB 2, Windows 7 boot loader will appear, with only Windows 7 as the only choice and also the default operating system, with a 30 second waiting time if no input is detected. I'm trying to see if it is possible to remove this 30-second waiting time. I've tried to follow the instructions on the Web by configuring default operating system in the control panel but seems there is something wrong with it. I've also tried to use "bcdedit enum /all" but still receives error prompts. Update: Added my boot tab screen in msconfig.

  Read the article

• windows server 2012 wont boot after instlling on iscsi device

  - by Nandan

  Windows server 2012 installed on a ISCI LUN. Problem noticed after first reboot. Windows boots only if setup DVD is present(i have to ignore "press any key to boot from DVD" prompt). to present the login Screen and everything looks great from here. But the server wont boot without the help of setup DVD. Can any one help me understand what would be the problem? Dell Workstation T3600 Intel Pro NIC (Capable of ISCI Boot and also enabled)

  Read the article

• Ubuntu 12.04 can't boot after installing with software RAID 1

  - by Bill

  I've been trying to install Ubuntu with software RAID on my server and there is obviously something that I don't understand about the process. This is the guide that I followed: https://help.ubuntu.com/11.04/serverguide/advanced-installation.html I have two identical 1 TB disks in my server. I went through the initial install process and manually set up my partitions. On each disk I set up: (1) 100 MB partition for EFI boot (I didn't originally have this but added it based on a forum post I found after my original install failed to boot, I ended up with EFIboot since that was what the 'guided partitioning' decided to do) (1) 970 MB partition for / (1) 30 MB partition for swap I then created new RAID 1 disks combining the two partitions, one from each disk, such that each partition is mirrored. I then configured their usage as stated above. After saving the configuration I said yes to boot in a degraded state. The rest of the setup went normally, no errors of any kind. I saw GRUB being installed and again no errors. However, after rebooting the server I get the dreaded 'Insert boot media' and nothing happens. I loaded up the recovery disk and the mdadm configuration looks correct. md0 is my EFIBoot partition md1 is my \ partition using ext4 md2 is my swap partition Running file -s /dev/md0 doesn't indicate that GRUB is there and so I attempted to reinstall GRUB using the recovery disk. I selected the md0 disk and it appeared to install just fine. Running file -s /dev/md1 shows the error needs journal recovery, I'm not sure if that's related or not or how to fix that. Rebooting gives me the same problem, no boot media found. I've searched around the internet but can't figure out what to do next or more importantly how to troubleshoot what exactly is going wrong. Thanks!

  Read the article

• Problem in the Windows boot screen

  - by Velmrugan

  Hi, Once i had kept a supervisor password to my windows boot screen, but now i forgot that password, Now i am unable to access the boot menu since its asking the password, all menu options are disabled. Is it possible to remove that password and can i get the boot menu default settings back? I had tried to change the jumper settings too, but the problem hasn't been solved. Processor: Intel Pentium dual core (2) OS : XP Thanks in Advance,

  Read the article

• Replacing GRUB2 with Windows boot loader

  - by KovBal

  I'm trying to replace GRUB2 with Windows' standard boot loader (bootmgr?), but I can't get it to work. My Windows 7 install is in a single NTFS partition, which is marked as active (boot flag is set). First, I tried the automatic repair with the install disk, but it didn't detect any problems. Then I ran bootrec /fixmbr and bootrec /fixboot, but all I got was a black screen at boot with a blinking cursor. After that I created a boot partition for GRUB2, I figured, at least I can use it to chainload, but it give me a "disk reading error". If I used GRUB's ntldr loader, than I got error 0xc0000225 (some sort of BCD error). I tried to rebuild the BCD from the rescue environment, and it was successful, but the error didn't go away. Update: I've tried to rebuild the BCD, but nothing changed...

  Read the article

< Previous Page | 102 103 104 105 106 107 108 109 110 111 112 113  | Next Page >