Search Results

Search found 7843 results on 314 pages for 'power over ethernet'.

Page 107/314 | < Previous Page | 103 104 105 106 107 108 109 110 111 112 113 114  | Next Page >

• CPU fan turns on and off repeatedly without booting

  - by rnso

  My PC has suddenly stopped starting up. On checking with case open, the CPU fan starts running when the power is turned on, but it stops after about 2-3 seconds, restarts again after about 2-3 seconds and the loop is repeated. There is no beep and nothing appears on the screen. On searching the internet, I found there could be several reasons for this. I tried removing hard-disk, CD drive, tightening connections etc but of no avial. I also tried using a new power supply but the response is the same. Where could be the problem and how can it be solved? Thanks in advance.

  Read the article

• What is the command to use to put your computer to sleep (not hibernate)?

  - by airrick

  I want to put my windows pc (win7) into a sleep state via command line (so i can bind to macro button on keyboard). The power button on the PC is setup to but the computer to sleep (but it's down on the floor and I'm too lazy to reach down) it exactly how I want it (sleeps using hybrid mode in case I loose power) The sleep command on the shutdown menu also works. most info I found says to use; %windir%\system32\rundll32.exe PowrProf.dll, SetSuspendState 0,1,0 But this puts the computer in hibernate mode. I do have hibernate disabled but using hybrid sleep. So, What is the command to use to put your computer to sleep (not hibernate)?

  Read the article

• Radiation from a UPS

  - by Erel Segal

  In our office, there are frequent eletric shortages that harm my desktop computer, so I wanted to install a UPS. However, my office-mates pointed me to papers talking about hazardous radiation from the UPS. The UPS manufacturers themselves recommend to put the UPS several meters away from humans, which is not possible because our office is small (the power is about 0.5 meters from us). As an alternative to UPS, my office-mates recommended that I switch to a laptop, which has a battery so it's immune to shortages. I have several questions: Is it true that the radiation from a laptop battery is lower than the radiation from a UPS? They do just the same thing - supply power using a battery! If the answer to 1 is yes - is there an alternative way to attach a battery, similar to a laptop battery, to a desktop computer? If the answer to 1 is no - how can I prove this to my office-mates, so that they let me use UPS?

  Read the article

• Thinkpad speaker turns mute - Linux Codec issue?

  - by Curlew

  At some point a few days ago the speakers on my Lenovo Thinkpad T410 (Model number: 2537A11) suddenly stopped working randomly. This error happens every time I watch a video or listen to a music file. The sound just abruptly stops. At the moment, I can't produce a single sound no matter what I do. I am using Debian GNU/Linux on this laptop and there doesn't appear to be anything else wrong (the fan is working, no abnormal heat (staying around ~40°C), no other obvious errors or problems). Here is the output of a nice program someone pointed me to: martin@martin:~/Downloads$ sudo python run.py --monitor Using temporary directory: /dev/shm/hda-analyzer You may remove this directory when finished or if you like to download the most recent copy of hda-analyzer tool. Downloading file hda_analyzer.py Downloading file hda_guilib.py Downloading file hda_codec.py Downloading file hda_proc.py Downloading file hda_graph.py Downloading file hda_mixer.py Downloaded all files, executing hda_analyzer.py Watching 1 cards ====================================== Sound is working normally and then it stops and the following lines appear: Diff for codec 0/0 (0x14f15069): --- +++ @@ -164,17 +164,17 @@ Power: setting=D0, actual=D0 Node 0x1f [Pin Complex] wcaps 0x400501: Stereo Pincap 0x00000010: OUT Pin Default 0x901701f0: [Fixed] Speaker at Int N/A Conn = Analog, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE Pin-ctls: 0x40: OUT - Power: setting=D0, actual=D0 + Power: setting=D3, actual=D3 Connection: 2 0x10* 0x11 Node 0x20 [Pin Complex] wcaps 0x400781: Stereo Digital Pincap 0x00000010: OUT Pin Default 0x40f001f0: [N/A] Other at Ext N/A Conn = Unknown, Color = Unknown DefAssociation = 0xf, Sequence = 0x0 Misc = NO_PRESENCE And now there is also an error in the dmesg output hda-intel: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj. I changed the bdl_pos_adj to various numbers (-1, 0, 64, 1024) and either there is no change at all or dmesg reports that the adjustment is too big. I wonder if this bdl_pos_adj is the real reason for the error. Here is my hardware information provided by alsa-info.sh website. Okay, i did some serious testing and even installed Windows and now i officially conclude that this is a hard-ware related issue with my Laptop speakers. Reason: The error occurs in my installed Debian Linux, an Ubuntu Live distribution and Windows XP No error-message appears in all of the OS. The sound just keeps running and i can't hear a thing. I tested different setups, including OSS, ALSA and the pulseaudio server on top If i use my new usb-headphones i can hear sound all the time without any sudden silences. So obviously, although hard to believe, my laptop speakers are not okay (never heard of similar cases). I'll award the bounty to anyone who can point me to good tutorials or the procedure how to exchange my T410 speakers (i still have warranty. The laptop was bought in Germany, but now i am in Denmark). Or to someone who can explain me the output from hda-analyzer (big log above).

  Read the article

• How do I negotiate for colo space?

  - by randy melder

  I guess this isn't a technical question, but it definitely is something IT teams deal with, so here goes: I'm looking at getting a rack at a local colocation facility. I'm weighing the options versus building out in a cloud platform. We are REALLY low bandwidth and power. There's a total of six hosts for the total operation. You can assume we use <= 10 amps of power and <= 2Mbps 95th percentile. Do you have any advice for getting the best deal?

  Read the article

• Laptop goes black after a minute or so

  - by ZEDA-NL

  I have a laptop that is behaving strangely. When I turn it on, it does everything what it is supposed to do, but after a minute or so I hear a Click and all goes black. It's like it turns off the power. It doesn't matter what the laptop is doing. It also happens when it's just waiting in the Bios setup menu. Has someone experienced this before? Can it be the power supply? Can it be a cooling problem? Any ideas? By the way, it's a Compaq Presario Laptop, maybe 3 years old already.

  Read the article

• Why does the CPU usage reach 100% when laptop is plugged in?

  - by Mayank

  I have an HP Elitebook 8440p with Windows 7 Ultimate, i7 Processor and 8 GB RAM. For the last couple of days, when I plug-in my laptop for charging, the CPU usage shoots up to 100% and remains there for around 15 minutes. No offending process shows up in Task Manager/Process Explorer but the laptop is practically unusable for that time. The CPU usage becomes normal when I remove the power cord but shoots up again when plugged back. This is happening with different power adapters/wall sockets so it might not be a faulty adapter issue. Why is this happening and any pointer to resolve this issue?

  Read the article

• Hibernate speed, and hard drive temperature

  - by cometbill

  My computer is taking in the region of 4 minutes or so, to hibernate 4GB of RAM. Also, resting my hand on the top of it is rather hot to the touch, so I ran CrystalDisk Info and that is reporting a temperature of 49 degrees C. I It's a Western Digital 5400 rpm drive, I've had it in the laptop since I bought it for most of the 2.75 years I've had it. Power on Count is 1219 Power on Hours is 3940 hours Boot up time is quicker than resuming from hibernate, too. Is there anything I can / should check ? Advice is greatly appreciated.

  Read the article

• X200 Tablet notebook won't start after BIOS Update

  - by THEn

  I have LENOVO X200 Tablet and I ran the BIOS Update and the computer won't start after the BIOS update. When I ran the BIOS update utility it ran everything fine and asked to restart the computer but it wont start screen is blank. I unplugged the power and took of the battery and put them back and still not starting. Now it has [Power On] indicator light on and screen is not starting. I tried pressing F1 button while trying to start the computer but it doesn't do react to anything. Please help how I can start my Tablet. The update utility is http://support.lenovo.com/en_US/downloads/detail.page?LegacyDocID=MIGR-70651 Does any body know if X200 have any kind of hardware switch to reset the BIOS or any thing? What would be the best way to fix my BIOS? Thank you.

  Read the article

• DSL to web connectivity is often lost

  - by broiyan

  I am experiencing a frequent web connectivity problem via a DSL modem. The problem usually shows up as a reload later screen inside of Google Chrome, as illustrated. My DSL service was fine for the first 2 months, but in the most recent month this problem has been occurring. I have this problem several times a day. A few weeks ago, I used to power cycle (off then on) the DSL modem but this usually did not solve the problem. However, in recent days, the power cycle does seem to fix the problem. When the problem occurs, the modem lights do not look unusual. All the lights are green or flashing green. This problem happens regardless of whether I am using ethernet or WiFi for the last few meters between the DSL modem and the computer. What is the likely cause? How can I help the phone company solve this? Their staff are not very effective at troubleshooting this.

  Read the article

• How do laptop battery voltages affect runtime?

  - by Bigbio2002

  I ordered a new battery for my faithful XPS M1710. I'm not sure of the voltage of the battery I have now, but the new one that the Dell rep got me (after 3-4 times confirming my phone number and laptop model number) is 14.8v. I was a bit concerned about potential incompatibilities (as most of the other compatible batteries listed were 11.1v), but I figure that there's no way that Dell would "recommend" batteries that wouldn't work or fry your system. Now, my question is, how does voltage affect battery life? If we assume the needed power draw to be constant, a higher voltage would indicate less amperage needed, therefore the battery would last longer before running out, yes? Or am I missing something? For reference: P=I*V P = power I = current V = voltage (duh)

  Read the article

• Dark Windows 7 Screen

  - by user147521

  My Gateway laptop -Windows 7- screen became too dark a few days ago after I finished installing Windows automatic update. I can see nothing unless I use a flashlight. Windows login screen is the only bright screen for few seconds. What should I do to resolve this issue? I checked power-saving/ Power Options settings and rebooting in Safe Mode. I tried to lower the refresh rate but it did not allow me. The laptop adapter type is ATI Radeon Xpress series. I uninstalled and reinstalled the driver. And the driver is up to-date. Any help would be appreciated.

  Read the article

• A gigabit network interface is CPU-limited to 25MB/s. How can I maximize the throughput?

  - by netvope

  I have a Acer Aspire R1600-U910H with a nForce gigabit network adapter. The maximum TCP throughput of it is about 25MB/s, and apparently it is limited by the single core Intel Atom 230; when the maximum throughput is reached, the CPU usage is about 50%-60%, which corresponds to full utilization considering this is a Hyper-threading enabled CPU. The same problem occurs on both Windows XP and on Ubuntu 8.04. On Windows, I have installed the latest nForce chipset driver, disabled power saving features, and enabled checksum offload. On Linux, the default driver has checksum offload enabled. There is no Linux driver available on Nvidia's website. ethtool -k eth0 shows that checksum offload is enabled: Offload parameters for eth0: rx-checksumming: on tx-checksumming: on scatter-gather: on tcp segmentation offload: on udp fragmentation offload: off generic segmentation offload: off The following is the output of powertop when the network is idle: Wakeups-from-idle per second : 61.9 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 90.9% (101.3) <interrupt> : eth0 4.5% ( 5.0) iftop : schedule_timeout (process_timeout) 1.8% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.9% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.5% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) And when the maximum throughput of about 25MB/s is reached: Wakeups-from-idle per second : 11175.5 interval: 10.0s no ACPI power usage estimate available Top causes for wakeups: 99.9% (22097.4) <interrupt> : eth0 0.0% ( 5.0) iftop : schedule_timeout (process_timeout) 0.0% ( 2.0) <kernel core> : clocksource_register (clocksource_watchdog) 0.0% ( 1.0) dhcdbd : schedule_timeout (process_timeout) 0.0% ( 0.6) <kernel core> : neigh_table_init_no_netlink (neigh_periodic_timer) Notice the 20000 interrupts per second. Could this be the cause for the high CPU usage and low throughput? If so, how can I improve the situation? As a reference, the other computers in the network can usually transfer at 50+MB/s without problems. A computer with a Core 2 CPU generates only 5000 interrupts per second when it's transferring at 110MB/s. The number of interrupts is about 20 times less than the Atom system (if interrupts scale linearly with throughput.) And a minor question: How can I find out what is the driver in use for eth0?

  Read the article

• iPad USB Charging Utility for Dell Optiplex

  - by BreakPhreak

  As you probably know already, an iPad requires a certain power on USB port to be charged from. Thus, some motherboard manufacturers (such as ASUS, Gigabyte etc) had released a special driver that recognizes that an iPad is connected to the port and adjust the USB power accordingly. On one of my computers (Gigabyte motherboard) it works fine. But other one is Dell Optiplex 780 and the regular googling by "<motherboard type> + iPad charging" doesn't seem to bring encouraging results. Just for completeness: no, the iPad is not being charged without any special driver installed (out of the box) either. Any suggestions will be welcomed.

  Read the article

• Windows 7: Use VirtualStore technology as user for own benefit?

  - by mfn

  I've researched a bit and came to the understanding that VirtualStore is part of the new UAC feature in Vista/W7 which is the file system part of the transparent data redirection and redirects write access to folders like program files to C:\User\<username>\AppData\Local\VirtualStore\ in lack of applications respecting the LUA principles. Now I'm interested if that kind of transparent redirection can also be used as a power to the user. Here's an example which comes to my mind: I install any kind of software to e.g. D:\Whatever\ThisAndThisApp\ and I set up things that, after initial installation, any write access to this folder is transparently redirected to e.g. D:\MyOwnVirtualStore\Whatever\ThisAndThisApp\file_only_writable_here.txt. Is this thinking too far or can I actually use that power of VirtualStore as a user on Windows 7? I'm using the Professional version of that matters.

  Read the article

• Complete machine freezes...at a loss

  - by user28818

  Guys, We built around 12 machines a few months ago to run Ubuntu. They each have the following specs: ASUS Z8NA-D6 motherboard Dual quad core Intel(R) Xeon(R) CPU E5520 @ 2.27GHz OCZ Mod Extreme Pro 500W power supply 12 GB Kingston RAM Nvidia GeForce 9800 GT graphics card My machine ran well for awhile. However, it started experiencing random lockups. These lockups are not X lockups, they are complete system freezes. The nic stops responding, the magic sysrq buttons won't work. The machine is dead. I first suspected RAM. Memtest86 didn't find anything, but I replaced the RAM anyway. Still, lockups. So I replaced the graphics card. Still, more lockups. They became more and more frequent and started to happen 2-3 times a day. So I replaced the motherboard and power supply in one fell swoop. Suddenly, no more lockups! Woohoo! Except, a week later, in the morning, the machine wouldn't wake up. I reset it, started it up, and the log files showed the last entry at around 11 pm the evening before. This has started occurring with more frequency...now just about every morning I come in, the machine is locked up, and has been since the night before. Yesterday, in the 3 weeks since I replaced the motherboard and power supply, the machine actually locked up on in in mid-work. This is the first time since replacing the two (MB and PS) that this happened while I was using it. All others occurred while I was away. I'm at a loss. Nothing is in syslog or message that would indicate a problem around the time of the lockup. Temps are good...I use lmsensors to monitor and have a script that writes the output to file every minute. They never get that high. The only thing I haven't replaced at this point is the case and the harddrives. I doubt either could be the cause. What would you do if you were in my shoes? Is there a troubleshooting approach I'm missing? For the record, all of the other machines, all eleven of them, don't have any problems. They're all running the same version of Ubuntu (Lucid) that I am. Thanks!

  Read the article

• PC won't boot with 4 prong CPU connector connected. Motherboard or CPU dead - which one? Both?

  - by scrot

  In the middle of use, my computer shut down. I tried to turn it on but it maybe comes on for half a second, shuts down, then flickers again very quickly about 2 seconds later before giving up completely. So I took everything apart and nailed it down to the power supply, the mobo, or the CPU. I had an extra old power supply around, hooked that up and it had the same problems, so that can't be it. When the 4 prong CPU connector is not connected, the motherboard 'functions' in that it stays on and runs the heat sink etc. Throw in the 4 prong connector and that's when it doesn't stay on. So it must be the CPU, right? Motherboard: ASUS P6X58D CPU: Intel i7-920 Bot are under warranty (supposedly) - should I get both replaced or what?

  Read the article

• SBS 2008 reinstall on new machine

  - by Jon

  We purchased a single license on Windows Small Business Server 2008 for a medical office, and soon after a power fault caused the server to overload, destroying the power supply and motherboard. I reinstalled on a new server, and have the domain up and running again, but under system properties it tells me I still need to activate windows, and that the product key currently entered is invalid for activation. I've been trying to figure out how to get in touch with Microsoft to explain the situation and get a new activation key issued without having to pay for another license which we can't afford, but the online documentation hasn't been particularly clear on the subject. Does anyone know how to do that, or if I do need the activation key to continue using SBS 2008? (It currently tells me I have 56 days left to activate) Any tips would be appreciated. I'm not strictly a computer guy and I'm feeling a little lost.

  Read the article

• further troubleshooting on a p8z77 motherboard

  - by Journeyman Geek

  I just bought a brand now asus p8z77 motherboard with a intel 3770. Its currently not booting - the system powers up for half a second and then powers down, and the CPU error light shines. I've tried switching ram between slots, switching PSUs, updating the bios (which can be done sans processor or ram on this model). Power: The 8 pin power connector is definitely in place correctly, and I've tried swapping PSUs between a new seasonic m12, and a known good cheapie PSU Ram: Ram is in the recommended slot for single stick operation, and tried swapping between the two sticks of DDR3 I have. Processor: Its installed correctly as far as I can tell, no obvious bent pins on the motherboard. At this point I'm guessing I'll need to RMA something. Are there any 'definitive' tests I can try, short of swapping CPU and motherboard that would let me know it is the CPU? Can I actually trust the error light on the motherboard?

  Read the article

• plugging in a 3.3V 50pin laptop HDD to USB?

  - by barlop

  I have a 50pin laptop hard drive. 1.8" wide. This 50pin connector concerns me.. Even if I get an adaptor, How can I know which side of the connector takes the power? I don't want to plug it in the wrong way. And I don't have n adaptor.. Could people link me to adaptors too. but main question is, which side to plug it in when I get the adaptor. I want to be sure. I do not want to blow the hdd. For the 3.3V I have a plan. Connecting green and black and using the orange cable(3.3v) to feed power. I am not too worried about that bit. But as I said.. Main thing is I want to know which side is 3.3V hard drive is MK6006GAH

  Read the article

• Windows Home Server Passwords Do Not Match [closed]

  - by Ben Fulton

  I have a Windows Home Server that chunks along just fine most of the time. I've never bothered to put it on a GPS and so it's vulnerable to power outages that happen a few times a year. This most recent time, it came back and seemed to be fine, but whenever I try to access a shared folder I get "Passwords do not match". They matched before the power went out, and I couldn't update the WHS password since I apparently didn't know the old one. How do I fix this?

  Read the article

• No internet access on Windows 7 - part 2

  - by Vnuk

  This is a continuation of my previous question. The problems started when I turned on my wireless connection for the first time. Since then, every time I boot my Windows 7, my LAN connection does not have internet access. In my previous question, I got a key answer (route delete). Now my procedure to get LAN internet connectivity (local network works fine) when I boot looks like this: Power on WLAN Disconnect LAN cable Power off WLAN Execute route delete 0.0.0.0 if 11 Connect LAN cable Now my LAN connection has internet access. Another behavior that I can't explain - while my LAN connection has no internet access, Network and Sharing center refers to it as Unknown network, with a public icon. When I go through the fore mentioned procedure, it is referred to with my home WLAN network name, with status connected, and the Unknown network disappears.

  Read the article

• Autoplay for USB drive keeps popping up

  - by Adam Haile

  I have a Seagate external 2TB USB drive that when I leave it plugged in, the Autoplay dialog asking what to do with the drive pops up about once every 30-60 minutes. No matter how many times I tell it to go away, it keeps coming back. I have tried multiple power supplies, USB cables, and all the USB ports on my machine...but it keeps doing the same thing. Also, this does not happen with the same drive on a different computer. Could this be some power or configuration setting that is causing this? I'm running Windows 7 x64 (the computer it works on is x86)

  Read the article

• Update a DNS to a for a dynamic IP

  - by zobgib

  I want to use my schools connection as a place to host a small webserver but one problem I have run into is anytime my server reboots I am given a new IP inside the schools range. All of the schools IP are public and therefor I can access my computer directly over WAN just via the IP given in ifconfig. I would like to be able to give my computer a dns which is easy enough when I change the Arecords to match the current IP of my computer. The problem is if my computer ever reboots (my school regularly cycles power at night and over holidays) I am assigned a new IP and have to realize it then update the Arecords This is inconvenient and I figure there must be a better way to keep the DNS records updated either via a script or my own BIND server. That way if there is a power cycle I can still access the server via a Domain Name. If you have any direction to point me in it would be much appreciated. I am running Ubuntu 10.04 if that helps :).

  Read the article

• How to know my wireless card has injection enabled?

  - by shrimpy

  I am playing around with aircrack. And was trying to see whether my wireless card on my laptop can pass the injection test And I end up seeing the following... does it mean my wireless card is not able to run aircrack? root@myubuntu:/home/myubuntu# iwconfig lo no wireless extensions. eth0 no wireless extensions. eth1 IEEE 802.11bg ESSID:"" Nickname:"" Mode:Managed Frequency:2.437 GHz Access Point: Not-Associated Bit Rate:54 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=5/5 Signal level=0 dBm Noise level=-57 dBm Rx invalid nwid:0 Rx invalid crypt:781 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 root@myubuntu:/home/myubuntu# aireplay-ng -9 eth1 ioctl(SIOCSIWMODE) failed: Invalid argument ARP linktype is set to 1 (Ethernet) - expected ARPHRD_IEEE80211, ARPHRD_IEEE80211_FULL or ARPHRD_IEEE80211_PRISM instead. Make sure RFMON is enabled: run 'airmon-ng start eth1 <#>' Sysfs injection support was not found either. root@myubuntu:/home/myubuntu#

  Read the article

< Previous Page | 103 104 105 106 107 108 109 110 111 112 113 114  | Next Page >