Search Results

Search found 7606 results on 305 pages for 'raam dev'.

Page 107/305 | < Previous Page | 103 104 105 106 107 108 109 110 111 112 113 114  | Next Page >

• Hard Disk Not Counting Reallocated Sectors

  - by MetaNova

  I have a drive that is reporting that the current pending sectors is "45". I have used badblocks to identify the sectors and I have been trying to write zeros to them with dd. From what I understand, when I attempt writing data directly to the bad sectors, it should trigger a reallocation, reducing current pending sectors by one and increasing the reallocated sector count. However, on this disk both Reallocated_Sector_Ct and Reallocated_Event_Count raw values are 0, and dd fails with I/O errors when I attempt to write zeros to the bad sectors. dd works fine, however, when I write to a good sector. # dd if=/dev/zero of=/dev/sdb bs=512 count=1 seek=217152 dd: error writing ‘/dev/sdb’: Input/output error Does this mean that my drive, in some way, has no spare sectors to be used for reallocation? Is my drive just in general a terrible person? (The drive isn't actually mine, I'm helping a friend out. They might have just gotten a cheap drive or something.) In case it is relevant, here is the output of smartctl -i : Model Family: Western Digital Caviar Green (AF) Device Model: WDC WD15EARS-00Z5B1 Serial Number: WD-WMAVU3027748 LU WWN Device Id: 5 0014ee 25998d213 Firmware Version: 80.00A80 User Capacity: 1,500,301,910,016 bytes [1.50 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Fri Oct 18 17:47:29 2013 CDT SMART support is: Available - device has SMART capability. SMART support is: Enabled UPDATE: I have run shred on the disk, which has caused Current_Pending_Sector to go to zero. However, Reallocated_Sector_Ct and Reallocated_Event_Count are still zero, and dd is now able to write data to the sectors it was previously unable to. This leads me with several other questions: Why aren't the reallocations being recored by the disk? I'm assuming the reallocation took place as I can now write data directly to the sector and couldn't before. Why did shred cause reallocation and not dd? Does the fact that shred writes random data instead of just zeros make a difference?

  Read the article

• How to diagnose storage system scaling problems?

  - by Unknown

  We are currently testing the maximum sequential read throughput of a storage system (48 disks total behind two HP P2000 arrays) connected to HP DL580 G7 running RHEL 5 with 128 GB of memory. Initial testing has been mainly done by running DD-commands like this: dd if=/dev/mapper/mpath1 of=/dev/null bs=1M count=3000 In parallel for each disk. However, we have been unable to scale the results from one array (maximum throughput of 1.3 GB/s) to two (almost the same throughput). Each array is connected to a dedicated host bust adapter, so they should not be the bottleneck. The disks are currently in JBOD configuration, so each disk can be addressed directly. I have two questions: Is running multiple DD commands in parallel really a good way to test maximum read throughput? We have noticed very high SWAPIN-% numbers in iotop, which I find hard to explain because the target is /dev/null How shoud we proceed in trying to find the reason for the scaling problem? Do you thing the server itself is the bottleneck here, or could there be some linux parameters that we have overlooked?

  Read the article

• Grub error 18, gparted not showing anything

  - by Montecristo

  Some week ago I started having some problems with my pc, sometimes it just freezed not allowing me to do anything. I had to turn it off and on and sometimes do it a couple of time even at startup. Now it does not start at all, grub is giving me error 18. I have found that a solution is to create a bootable partition in the first sector of the disk. gparted does not recognize any partition, the window in which there would be my partitions is empty. sudo fdisk -l does not output anything. If I type sudo mount /dev/sda and then tab tab to autocomplete these are the devices coming out: sda sda1 sda2 sda5. If I launch sudo mount -t ext3 /dev/sda1 disk I get the following error: mount: wrong fs type, bad option, bad superblock on /dev/sda1, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so dmesg outputs [ 1831.974847] EXT3-fs: unable to read superblock Do you know how to solve this issue? I'm not completely sure this is a software problem, should I try with a new hard disk?

  Read the article

• how can i move ext3 partition to the beginning of drive without losing data?

  - by Felipe Alvarez

  I have a 500GB external drive. It had two partitions, each around 250GB. I removed the first partition. I'd like to move the 2nd to the left, so it consumes 100% of the drive. How can this be accomplished without any GUI tools (CLI only)? fdisk Disk /dev/sdd: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xc80b1f3d Device Boot Start End Blocks Id System /dev/sdd2 29374 60801 252445410 83 Linux parted Model: ST350032 0AS (scsi) Disk /dev/sdd: 500GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 2 242GB 500GB 259GB primary ext3 type=83 dumpe2fs Filesystem volume name: extstar Last mounted on: <not available> Filesystem UUID: f0b1d2bc-08b8-4f6e-b1c6-c529024a777d Filesystem magic number: 0xEF53 Filesystem revision #: 1 (dynamic) Filesystem features: has_journal dir_index filetype needs_recovery sparse_super large_file Filesystem flags: signed_directory_hash Default mount options: (none) Filesystem state: clean Errors behavior: Continue Filesystem OS type: Linux Inode count: 15808608 Block count: 63111168 Reserved block count: 0 Free blocks: 2449985 Free inodes: 15799302 First block: 0 Block size: 4096 Fragment size: 4096 Blocks per group: 32768 Fragments per group: 32768 Inodes per group: 8208 Inode blocks per group: 513 Filesystem created: Mon Feb 15 08:07:01 2010 Last mount time: Fri May 21 19:31:30 2010 Last write time: Fri May 21 19:31:30 2010 Mount count: 5 Maximum mount count: 29 Last checked: Mon May 17 14:52:47 2010 Check interval: 15552000 (6 months) Next check after: Sat Nov 13 14:52:47 2010 Reserved blocks uid: 0 (user root) Reserved blocks gid: 0 (group root) First inode: 11 Inode size: 256 Required extra isize: 28 Desired extra isize: 28 Journal inode: 8 Default directory hash: half_md4 Directory Hash Seed: d0363517-c095-4f53-baa7-7428c02fbfc6 Journal backup: inode blocks Journal size: 128M

  Read the article

• Symbolic link modification for HP unix

  - by kalpesh

  Hi David Zaslavsky, Recently i was working on modifying the Symbolic links ... for a particular files.. while searching on internet i saw your post ... I am trying to use this script which you had posted .. find /home/user/public_html/qa/ -type l \ -lname '/home/user/public_html/dev/*' -printf \ 'ln -nsf $(readlink %p|sed s/dev/qa/) $(echo %p|sed s/dev/qa/)\n'\ script.sh SO i tried to modify your script for my problem .. in Hp unix env.. but it seems that the -lname command does not works for HP unix. do you know something equivalent that i can use ... Just to give you and idea of my problem ... I want to change all the symbolic links inside a particular folder .. New Symbolic link -- /base/testusr/scripts Old Symbolic link -- /base/produsr/scripts Now folder "A" contains more than 100 different files having soft links which points to this path -- /base/produsr/scripts But what I want is that the files inside folder A to point to this soft link --/base/testusr/scripts I am trying to achieve in Hp unix ... would really appreciate your help on this ...

  Read the article

• Is there a command to change primary group for a new user in Cygwin?

  - by Rob Gilliam

  Is there a way to set a (new) user's primary group in Cygwin's /etc/passwd file without hand-editing the file? I have a local group set up for members of the Dev Team on a Windows Server 2008 R2 box so that we can all modify a particular group files, but the regular users can only read them. As some of the work we do uses scripts that rely on Cygwin tools, this group is also in the /etc/group file. When I need to add a new user to the "Dev Team" group, I add them in Server Manager, and then use mkpasswd to add that user to Cygwin's /etc/passwd file. Unfortunately, they get the regular Domain Users group assigned as their primary group and I then have to go in and edit the passwd file to change the group. I now need to write some instructions for someone else who is not au fait with UNIX/Linux/Cygwin so that they can set up new Dev Team users and obviously "hand editing" /etc/passwd is a recipe for disaster if you don't know what you're doing. So, is there a way of getting mkpasswd to set a different primary group, or another tool like Linux's usermod which can be used for the purpose of changing the group in a more controlled manner?

  Read the article

• GRUB having problems with my sda1 UUID

  - by Igoru

  I was having trouble trying to setup triple boot on my computer... (Take a look at this thread if you think it would help). I ended up by having a GRUB menu that has Ubuntu entries and "Windows" entry, that calls an EasyBCD menu to choose between Windows 7 and XP. Everything would be fine if, only if, GRUB was set up correctly. I can't find why, but it throws me this when I try to open Ubuntu: I've already tried to remove the menu.lst and do a grub-update, and a grub-install too. I tried to create a symlink to /dev/sda1 at /dev/disk/by-uuid/<<uuid that is there>>, just like the other UUIDs that were there... But I couldn't find that symlink at that busybox that opened when it thrown me the error. Any ideas? [UPDATE] This is the GRUB entry with problems: title Ubuntu 9.04, kernel 2.6.28-15-generic uuid b1ed36e5-4d84-4eb8-86ef-6f1135ffc238 kernel /boot/vmlinuz-2.6.28-15-generic root=UUID=b1ed36e5-4d84-4eb8-86ef-6f1135ffc238 ro quiet splash initrd /boot/initrd.img-2.6.28-15-generic quiet And this my /dev/disk/by-uuid folder: 04DCBCFBDCBCE856 - ../../sdb1 (NTFS backup disk) 4434E77734E769FE - ../../sda4 (NTFS WinXP) ACB09F0DB09EDCE0 - ../../sda2 (NTFS Win7) b5311be8-a853-4fdd-aed5-d65974b3c0c4 - ../../sda5 (EXT4 home) C04B-4D97 - ../../sdc (FAT32 live-pendrive from which i'm running) D28447F68447DB9B - ../../sda6 (NTFS files partition) e0e88f38-d815-423a-9d5e-64b9c74a8b92 - ../../sda7 (swap)

  Read the article

• Update Grub on Squeeze - Kernel downgrade due VMware Server

  - by vodoo_boot

  I happen to run into various problems regarding grub and kernels. I don't really care about the kernel internas. All I want is VMware server in that dedicated root-server. 1.) What is a bzImage vs. vmlinuz? kaze:~# ls /boot/ System.map-2.6.32-5-amd64 bzImage-2.6.33.2 config-2.6.33.2 initrd.img-2.6.32-5-amd64 System.map-2.6.33.2 bzImage-2.6.35.6 config-2.6.35.6 vmlinuz-2.6.32-5-amd64 System.map-2.6.35.6 config-2.6.32-5-amd64 grub I updated my menu.lst (grub2): timeout 5 default 0 fallback 1 title 2.6.32.5 kernel (hd0,1)/boot/vmlinuz-2.6.32-5-amd64 root=/dev/sda2 panic=60 noapic acpi=off title 2.6.35.6 kernel (hd0,1)/boot//bzImage-2.6.35.6 root=/dev/sda2 panic=60 noapic acpi=off title 2.6.32.3 kernel (hd0,1)/boot//bzImage-2.6.33.2 root=/dev/sda2 panic=60 noapic acpi=off That doesn't do well... I think the vmlinuz file is missing initrd or so. Dunno. In fact I don't give too much about kernel boot voodoo as long as it works. update-grub(2) does not work. Does anybody know what magical trick there is to get the 2.6.32-5 booting? 2.) I thought t follow the Deban wiki.. I cannot get header-files for the installed 35.6 or 33.2 kernel in the repositories. I cannot build foreign headers because they will not match the running kernel. So how does one deal with that situtation? I'd prefer not to have to downgrade the kernel. Thanks for any answers!

  Read the article

• Website hosted on my virtualbox web server not displaying images or applying css when viewed through phone

  - by WebweaverD

  I would really appreciate it if someone could help me. Please let me know if you need more info in the comments. My Set Up I have a windows 7 pc. On it I run a virtual box VM with a ubuntu 12 guest os and LAMP setup. I share files between the two machines using samba from linux to windows and using windows file sharing (Workgroup) the other way round. The vm is set up with a bridged network adapter and can happily serve web pages to my host machine. I use DHCP reservations on my home wireless router/modem to reserve an ip for the vm and give it a sitename.dev in my windows host file so I can access it at sitename.dev through the browser. The Problem So far so good but I have a dev project which needs a lot of mobile template development, now obviously I can use a browser plugin to simulate a mobile device but I would like to be able to see the real thing easily on my phone during development. So ideally I would like a similar setup on my iphone to my windows setup Now I'm not great on networking and dont have much experience with web server set up. So when I typed the ip of my virtual box into my iphone i wasnt expecting to see anything. I was pleasantly surprised when my site loaded up. The javascript even seems to be running but the images and css are not happening. My Question 1) What is happening here, is it something to do with the bridged set up on the vm network? 2)How do I make the sites load properly through my phone Notes I've also tried another phone. The same sites viewed on live servers work fine.

  Read the article

• grub refuses to install to raid array

  - by ronno

  I have a software raid 0 setup with dual booting Windows 7 and Ubuntu 12.04. The GRUB bootloader that is already on the hard drive seems to work fine. However, since the latest package update for grub, it refuses to install the new version to the hard disk. grub-install throws the following error: /usr/sbin/grub-probe: error: cannot find a GRUB drive for /dev/mapper/< raid name_RAID0p9. Check your device.map. Auto-detection of a filesystem of /dev/mapper/< raid name_RAID0p9 failed. Try with --recheck. If the problem persists please report this together with the output of "/usr/sbin/grub-probe --device-map="/boot/grub/device.map" --target=fs -v /boot/grub" to < [email protected] update-grub pops the same "/usr/sbin/grub-probe: error: cannot find a GRUB drive for /dev/mapper/< raid name_RAID0p9. Check your device.map." every alternate line. I don't understand what exactly is going on. I'm afraid to reinstall the grub package because it might mess up the boot, which currently works fine. Is it safe to just ignore this?

  Read the article

• SSH not working through Double NAT

  - by d_inevitable

  I am trying to setup port forwarding for ssh through 2 NATs The first Router translates my internet IP to my outer network (10.1.7.0). In the outer network there's a second Router that does NAT to my inner network (192.168.1.0). The target server is connected to both, the outer network and the inner network. I cannot change the port forwarding options for outer router. It is currently configured to forward the SSH and HTTP port to the router for the inner network. Internet + | v +-----------------+ +------------------+ | Outer Router | | Inner Router | |-----------------| |------------------| | | SSH HTTP | | +----+ +--------------------->| | | | | | | | | | | | | +-------+---------+ +------+---------+-+ | | | | | | | | | | | | | | +------------------+ | SSH | | | | Server | | | | | |------------------| | | | +-----------> |<-------+ | | | | |HTTP (testing) | +------------------+ | | | +------v------------------+ | | Outer Workstation | +-------------------+ | |-------------------------| | Inner Workstation| | | | |-------------------| | | | | |<----------------+ +-------------------------+ | | +-------------------+ When connecting from a outer workstation to the address of the inner router, then both SSH and HTTP work fine. When connecting from the internet to my public ip with HTTP, the connection works fine as well. However SSH just times out. Most likely because the reply is not routed back properly. I suspect its either because of the SSH itself, or because the server is connected to both, the inner and outer network. Any ideas how I could resolve this issue? The routes on the server are currently: ip route show default via 10.1.7.254 dev eth0 metric 100 10.1.7.0/24 dev eth0 proto kernel scope link src 10.1.7.1 192.168.1.0/24 dev eth1 proto kernel scope link src 192.168.1.2 Do I have to change this? If so how?

  Read the article

• disk space keeps filling up on EC2 instance with no apperent files/directories

  - by sasher

  How come os shows 6.5G used but I see only 3.6G in files/directories? Running as root on an Amazon Linux AMI (seems like Centos), lots of free memory available, no swapping going on, no apparent file descriptors issue. The only thing I can think of is a log file that was deleted while applications append to it. Disk space usage is slowly but continuously rising towards full capacity (~1k/min with very small decreases from time to time) Any explanation? Solution? du --max-depth=1 -h / 1.2G /usr 4.0K /cgroup 22M /lib64 11M /sbin 19M /etc 52K /dev 2.1G /var 4.0K /media 0 /sys 4.0K /selinux du: cannot access /proc/14024/task/14024/fd/4': No such file or directory du: cannot access<br/> /proc/14024/task/14024/fdinfo/4': No such file or directory du: cannot access /proc/14024/fd/4': No such file or directory du: cannot<br/> access/proc/14024/fdinfo/4': No such file or directory 0 /proc 18M /home 4.0K /logs 8.1M /bin 16K /lost+found 12M /tmp 4.0K /srv 35M /boot 79M /lib 56K /root 67M /opt 4.0K /local 4.0K /mnt 3.6G / df -h Filesystem Size Used Avail Use% Mounted on /dev/xvda1 7.9G 6.5G 1.4G 84% / tmpfs 3.7G 0 3.7G 0% /dev/shm sysctl fs.file-nr fs.file-nr = 864 0 761182

  Read the article

• how to get ip address of a PPP(Point-to-Point Protocol) network interface?

  - by Xsmael

  I have a Linux machine with two network interfaces, and I'd like to get the IP address of the PPP interface w1g1 but it doesn't show up in ifconfig. There is a public IP on the PPP interface, but there is no internet connection, I'm trying to troubleshoot but I need to get the IP address of the interface and I can't. ifconfig : eth0 Link encap:Ethernet HWaddr 00:30:48:8D:F0:2C inet addr:192.168.2.254 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::230:48ff:fe8d:f02c/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:9970 errors:0 dropped:567 overruns:0 frame:0 TX packets:4338 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:1441024 (1.3 MiB) TX bytes:915814 (894.3 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:675 errors:0 dropped:0 overruns:0 frame:0 TX packets:675 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:50659 (49.4 KiB) TX bytes:50659 (49.4 KiB) w1g1 Link encap:Point-to-Point Protocol UP POINTOPOINT RUNNING NOARP MTU:240 Metric:1 RX packets:748994 errors:0 dropped:0 overruns:0 frame:0 TX packets:748992 errors:0 dropped:0 overruns:0 carrier:3 collisions:0 txqueuelen:100 RX bytes:179758560 (171.4 MiB) TX bytes:179758080 (171.4 MiB) Interrupt:177 Memory:f881c400-f881e3ff w1g1 is connected to a modem by an RJ45<-Serial cable and the modem is connected to the phone line. The modem is a NOKIA DNT2Mi you can see it here Routing table : 192.168.2.0/24 dev eth0 proto kernel scope link src 192.168.2.254 169.254.0.0/16 dev eth0 scope link default via 192.168.2.180 dev eth0

  Read the article

• File descriptor linked to socket or pipe in proc

  - by primero

  i have a question regarding the file descriptors and their linkage in the proc file system. I've observed that if i list the file descriptors of a certain process from proc ls -la /proc/1234/fd i get the following output: lr-x------ 1 root root 64 Sep 13 07:12 0 -> /dev/null l-wx------ 1 root root 64 Sep 13 07:12 1 -> /dev/null l-wx------ 1 root root 64 Sep 13 07:12 2 -> /dev/null lr-x------ 1 root root 64 Sep 13 07:12 3 -> pipe:[2744159739] l-wx------ 1 root root 64 Sep 13 07:12 4 -> pipe:[2744159739] lrwx------ 1 root root 64 Sep 13 07:12 5 -> socket:[2744160313] lrwx------ 1 root root 64 Sep 13 07:12 6 -> /var/lib/log/some.log I get the meaning of a file descriptor and i understand from my example the file descriptors 0 1 2 and 6, they are tied to physical resources on my computer, and also i guess 5 is connected to some resource on the network(because of the socket), but what i don't understand is the meaning of the numbers in the brackets. Do the point to some property of the resource? Also why are some of the links broken? And lastly as long as I asked a question already :) what is pipe?

  Read the article

• Why is REMOTE_ADDR only sometimes available as an Apache environment variable?

  - by Xiong Chiamiov

  To avoid having to parse X-Forwarded-For in Varnish, I'm trying to just set a header on the SSL terminator (currently Apache) that stores the direct client IP in a header. On our development machine, this works: RequestHeader set X-Foo %{REMOTE_ADDR}e However, in staging it doesn't. Specifically, the header is empty, as illustrated by both varnishlog: 13 TxHeader b X-Foo: (null) (On the development machine, this shows the IP address as expected.) Similarly, logging REMOTE_ADDR shows that it only appears to be populated on the dev machine: # Config LogFormat "%{X-Forwarded-For}i %{REMOTE_ADDR}e" combined CustomLog "/var/log/httpd/access_log" combined # Log file, staging <my ip> - # Log file, development <my ip> <my ip> Since the dev machine is, well, a dev machine, it is different in a number of ways; however, I can't track down which difference is causing this. The versions of Apache are the same (2.2.22), and I don't see anything relevant in any of the standard config files or /etc/sysconfig/httpd. And the rest of the system is reasonably similar, since they're built off the same CentOS 5 base image. I can't even tell from the Apache documentation whether REMOTE_ADDR is expected to exist or not as an environment variable, but it clearly works on one machine, whether by fluke or design, and the inconsistency is driving me mad.

  Read the article

• Input/output error reading USB backup drive on CentOS 6.4

  - by Kev

  I'm suddenly seeing some strange behaviour on our USB backup drive that doesn't make sense to me: (2013-10-21 14:58:23 [root@newdc /]$ cd /mnt/backup/ (2013-10-21 14:59:03 [root@newdc backup]$ ls -la ls: reading directory .: Input/output error total 0 (2013-10-21 14:59:05 [root@newdc backup]$ df -h /mnt/backup Filesystem Size Used Avail Use% Mounted on /dev/sda1 917G 843G 28G 97% /mnt/backup How is it possible for the OS to know how much is in use, but I can't ls any of it as root? Or more to the point, what problem does this indicate? /var/log/messages said this: Oct 21 14:57:54 g5 kernel: EXT4-fs error (device sda1): ext4_journal_start_sb: Detected aborted journal Oct 21 14:57:54 g5 kernel: EXT4-fs (sda1): Remounting filesystem read-only But...read-only is something different than 'throw an io error'... After unmounting to try fsck on it, I had someone on-site look at it, and the drive was not spun up, and had a slow-flashing light, which I believe means it was in a power-suspend mode. So I had them unplug and replug the USB cable, and now (before remounting) it says: fsck from util-linux-ng 2.17.2 e2fsck 1.41.12 (17-May-2010) /dev/sda1: clean, 2805106/61046784 files, 181934167/244182016 blocks I then mount it and now ls works and df reports: Filesystem Size Used Avail Use% Mounted on /dev/sda1 917G 680G 191G 79% /mnt/backup What would cause it to go into such a state without being asked to? Why all the weird behaviour, and now it appears to not be corrupt?

  Read the article

• Automatically creating volume partitions on boot

  - by Justin Meltzer

  I followed this guide: http://www.mongodb.org/display/DOCS/Amazon+EC2+Quickstart to set up Mongodb. It had me create a RAID 10 array out of the four devices on EBS. Then it had me create a physical volume, a volume group, and three logical volumes out of that RAID 10 array. Lastly it had me create ext4 filesystems out of the logical volumes and mount them. Now the quickstart guide had me put two things in place so that these steps would be replicated on reboot of the system. It had me add some instructions to the mdadm.conf file to automatically create the RAID 10 array, and it also had me add instructions to the fstab file to automatically mount the filesystem for each logical volume. However, the quickstart guide does not have anything for automatically creating the logical volumes from the RAID 10 array. I checked my system and see that each of the four devices are part of a RAID array: $ sudo mdadm -Q /dev/sdh1 /dev/sdh1: is not an md array /dev/sdh1: device 0 in 4 device unknown raid10 array. Use mdadm --examine for more detail. However, the filesystem is never created or mounted from fstab because it's trying to mount it from logical volumes that were never created (or so it seems). My question is, how can I automatically accomplish all the steps from the quickstart guide on a reboot of the system, and what config file do I need to add data to so that I can automatically create these volume partions after the RAID 10 is created but before the filesystem is mounted. Also I'm unsure whether fstab actually creates and mounts the filesystem or just mounts the filesystem.

  Read the article

• where is my disk space?

  - by user166241

  I recently had a problem with .xsession-errors file - it became very big ( 90GB) and took all disk space: How I can check what takes disk space in /tmp?. I cleaned it with command > .xsession-errors but after an hour it became large again. So I deleted it (rm .xsession-errors) - it helped because it wasn't recreated but again after hour disk space disappeared - now there is no .xsession-errors anymore but I don't know where is the memory: df Filesystem 1K-blocks Used Available Use% Mounted on /dev/sda1 106640456 101223392 4 100% / udev 8166744 8 8166736 1% /dev tmpfs 3270224 972 3269252 1% /run none 5120 0 5120 0% /run/lock none 8175552 152 8175400 1% /run/shm du -sc * .[^.]* | sort -n 0 initrd.img 0 initrd.img.old 0 proc 0 sys 0 vmlinuz 0 vmlinuz.old 4 cdrom 4 lib64 4 media 4 mnt 4 selinux 8 dev 12 srv 16 lost+found 68 tmp 1124 run 3396 lib32 5164 .rpmdb 5540 root 8888 sbin 9120 bin 17132 etc 106080 opt 116956 boot 861908 lib 3530584 usr 3821836 var 13371260 home 21859112 total So there is around 100GB used but executing du -sc * .[^.]* | sort -n in root directory finds only ~21 GB - so what takes 80GB?? How to check it? I suspect that when I deleted the `.xsession-errors' file the errors were redirected somwhere else - but where?

  Read the article

• Get more space for redis in unix server

  - by DevTraveler

  In our app we have only windows servers beside the cases we use redis queues. This case , we use unix server created by amazon. As you can see we do not have a lot of space available and we want to make sure redis has enough space to work without getting stuck. I am little bit new in unix and after reading some data about the unix file system i still was not fully sure how can i give the redis drive (it is in the home directory) more space. I see the mnt that has a lot of space but read it is temporary for cd-rom and network drives. Can you help me figure out how to get more space to my redis ? If it is possible i prefer not to re-install the redis server. Filesystem Size Used Avail Use% Mounted on /dev/xvda1 7.9G 6.7G 880M 89% / udev 7.4G 4.0K 7.4G 1% /dev tmpfs 3.0G 152K 3.0G 1% /run none 5.0M 0 5.0M 0% /run/lock none 7.4G 0 7.4G 0% /run/shm /dev/xvdb 414G 30G 364G 8% /mnt Thanks.

  Read the article

• file system damage

  - by jffrs

  I try recover the backup superblock on /dev/sda2 that contain ubuntu 12.04 LTS and partition ext4 with livecd ubuntu 10.04. the message is below root@ubuntu:/home/ubuntu# fsck.ext4 -b 163840 -B 4096 /dev/sda2 e2fsck 1.41.11 (14-Mar-2010) /dev/sda2 was not cleanly unmounted, check forced. Resize inode not valid. Recreate? yes Pass 1: Checking inodes, blocks, and sizes Programming error? block #7963637 claimed for no reason in process_bad_block. Programming error? block #11240437 claimed for no reason in process_bad_block. Root inode is not a directory. Clear? yes Inode 712 is in extent format, but superblock is missing EXTENTS feature Fix? yes Inode 98519 has compression flag set on filesystem without compression support. Clear? yes Inode 98519 has INDEX_FL flag set but is not a directory. Clear HTree index? what's the correct procedure?

  Read the article

• Mercurial to Mercurial to Subversion Workflow Problem

  - by Dalroth

  We're migrating from Subversion to Mercurial. To facilitate the migration, we're creating an intermediate Mercurial repository that is a clone of our Subversion repository. All developers will be begin switching over to the Mercurial repository, and we'll periodically push changes from the intermediate Mercurial repository to the existing Subversion repository. After a period of time, we'll simply obsolete the Subversion repository and the intermediate Mercurial repository will become the new system of record. Dev 1 Local --+--> Mercurial --+--> Subversion Dev 2 Local --+ + Dev 3 Local --+ + Dev 4 -------------------------+ I've been testing this out, but I keep running into a problem when I push changes from my local repository, to the intermediate Mercurial repository, and then up into our Subversion repository. On my local machine, I have a changeset that is committed and ready to be pushed to our intermediate Mercurial repository. Here you can see it is revision #2263 with hash 625... I push only this changeset to the remote repository. So far, everything looks good. The changeset has been pushed. hg update 1 files updated, 0 files merged, 0 files removed, 0 files unresolved I now switch over to the remote repository, and update the working directory. hg push pushing to svn://... searching for changes [r3834] bmurphy: database namespace pulled 1 revisions saving bundle to /srv/hg/repository/.hg/strip-backup/62539f8df3b2-temp adding branch adding changesets adding manifests adding file changes added 1 changesets with 1 changes to 1 files rebase completed Next, I push the change up to Subversion, works great. At this point, the change is in the Subversion repository and I return attention back to my local client. I pull changes to my local machine. Huh? I've now got two changesets. My original changeset appears as a local branch now. The other changeset has a new revision number 2264, and a new hash 10c1... Anyway, I update my local repo to the new revision. I'm now switched over. So, I finally click the "determine and mark outgoing changesets" and as you can see Mercurial still wants to push out my previous changesets even though they've already been pushed. Clearly, I'm doing something wrong. I also can't merge the two revisions. If I merge the two revisions on my local machine, I end up with a "merge" commit. When I push that merge commit out to the intermediate Mercurial repository, I can no longer push changes out to our Subversion repository. I end up with the following problem: hg update 0 files updated, 0 files merged, 0 files removed, 0 files unresolved hg push pushing to svn://... searching for changes abort: Sorry, can't find svn parent of a merge revision. and I have to rollback the merge to get back to a working state. What am I missing?

  Read the article

• Generating a salt in PHP

  - by qster

  What's the best way to generate a cryptographically secure 32 bytes salt in PHP, without depending on libraries seldom included in typical PHP installations? After some googling I discovered that mt_rand is not considered secure enough, but I haven't found a suggestion for a replacement. One article suggested reading from /dev/random but not only this won't work on windows; it is also very slow. I want a reasonable balance between security and speed (ie, it shouldn't take 20 seconds to generate 512 bytes, like /dev/random usually does)

  Read the article

• Bazaar newbie question about repository structures

  - by esc1729

  I want to use Bazaar on Windows XP for web-development and related tasks. Most of the files are edited locally and then transferred via FTP to the server. Just now the repository sits on my local workstation. Later on it should be shared locally with some co-workers. Perhaps we will use a local Linux server as a centralized repository, but this structure is not decided for now. But first I need to understand the impacts of the different repository setups, which I do not at all. Using Bazaar-Explorer on Windows XP I’ve created a ‘shared tree repository’ from the option list of the init-dialogue in some location dev-filter/. Bazaar Explorer tells me: Created repository with treeless branches at F:/bzr.local/dev-filter Created branch at F:/bzr.local/dev-filter/trunk Created working tree at F:/bzr.local/dev-filter/work OK so far. Now I move a bunch of files into the work directory and add and commit them as Rev 1 ‘Start Revision’. Then I work on some of these files and commit them again as Rev 2. Here my confusion starts. Shouldn’t both revisions go into the trunk? The trunk is still empty, beside the .bzr directory which only holds some management information. If I delete my working directory, which I have tried during these first experiments, everything is gone. There’s obviously no hidden storage of those files. OK. Perhaps I need to push it into the trunk? This does not work either. Entering the work/ directory and initializing the ‘push’ to the trunk, Bazaar-Explorer tells me No new revisions to push. So what? This looks like a severe conceptual misunderstanding about what should happen on my side. Edit, 2010-02-03: Some conclusions What I learned meanwhile is this: I think I should switch to the command line until I really understand what’s going on, at least for creating the repositories and branches. Bazaar Explorer introduces a new level of abstraction which I only can handle if I understand the level beneath One of the secrets of working with Bazaar at least for me is to understand those .bzr directories, their particular properties and states when created with ‘bzr init’, ‘bzr init-repository’, ‘bzr branch’ etc. in all their variants and how they are plumped together. While there’s a whole chapter of ‘Organizing your workspace’ in the Bazaar User Guide, it’s more or less workflow oriented. The manual contains a lot of directory structures for the given examples. What I would prefer beside this and have not (or only rudimentary) found so far is some graphical representation of those ‘Lego like’ .bzr building blocks which create the linking of all the parts. So I started to invent some simple notation while working through the examples and looking into the .bzr directories to document what information is stored there, where does it come from, how and to what is it linked, is it complete or shared, etc. Erich Schreiber

  Read the article

• Linux - Only first virtual interface can ping external gateway

  - by husvar

  I created 3 virtual interfaces with different mac addresses all linked to the same physical interface. I see that they successfully arp for the gw and they can ping (the request is coming in the packet capture in wireshark). However the ping utility does not count the responses. Does anyone knows the issue? I am running Ubuntu 14.04 in a VmWare. root@ubuntu:~# ip link sh 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000 link/ether 00:0c:29:bc:fc:8b brd ff:ff:ff:ff:ff:ff root@ubuntu:~# ip addr sh 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000 link/ether 00:0c:29:bc:fc:8b brd ff:ff:ff:ff:ff:ff inet6 fe80::20c:29ff:febc:fc8b/64 scope link valid_lft forever preferred_lft forever root@ubuntu:~# ip route sh root@ubuntu:~# ip link add link eth0 eth0.1 addr 00:00:00:00:00:11 type macvlan root@ubuntu:~# ip link add link eth0 eth0.2 addr 00:00:00:00:00:22 type macvlan root@ubuntu:~# ip link add link eth0 eth0.3 addr 00:00:00:00:00:33 type macvlan root@ubuntu:~# ip -4 link sh 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000 link/ether 00:0c:29:bc:fc:8b brd ff:ff:ff:ff:ff:ff 18: eth0.1@eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default link/ether 00:00:00:00:00:11 brd ff:ff:ff:ff:ff:ff 19: eth0.2@eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default link/ether 00:00:00:00:00:22 brd ff:ff:ff:ff:ff:ff 20: eth0.3@eth0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default link/ether 00:00:00:00:00:33 brd ff:ff:ff:ff:ff:ff root@ubuntu:~# ip -4 addr sh 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever root@ubuntu:~# ip -4 route sh root@ubuntu:~# dhclient -v eth0.1 Internet Systems Consortium DHCP Client 4.2.4 Copyright 2004-2012 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0.1/00:00:00:00:00:11 Sending on LPF/eth0.1/00:00:00:00:00:11 Sending on Socket/fallback DHCPDISCOVER on eth0.1 to 255.255.255.255 port 67 interval 3 (xid=0x568eac05) DHCPREQUEST of 192.168.1.145 on eth0.1 to 255.255.255.255 port 67 (xid=0x568eac05) DHCPOFFER of 192.168.1.145 from 192.168.1.254 DHCPACK of 192.168.1.145 from 192.168.1.254 bound to 192.168.1.145 -- renewal in 1473 seconds. root@ubuntu:~# dhclient -v eth0.2 Internet Systems Consortium DHCP Client 4.2.4 Copyright 2004-2012 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0.2/00:00:00:00:00:22 Sending on LPF/eth0.2/00:00:00:00:00:22 Sending on Socket/fallback DHCPDISCOVER on eth0.2 to 255.255.255.255 port 67 interval 3 (xid=0x21e3114e) DHCPREQUEST of 192.168.1.146 on eth0.2 to 255.255.255.255 port 67 (xid=0x21e3114e) DHCPOFFER of 192.168.1.146 from 192.168.1.254 DHCPACK of 192.168.1.146 from 192.168.1.254 bound to 192.168.1.146 -- renewal in 1366 seconds. root@ubuntu:~# dhclient -v eth0.3 Internet Systems Consortium DHCP Client 4.2.4 Copyright 2004-2012 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Listening on LPF/eth0.3/00:00:00:00:00:33 Sending on LPF/eth0.3/00:00:00:00:00:33 Sending on Socket/fallback DHCPDISCOVER on eth0.3 to 255.255.255.255 port 67 interval 3 (xid=0x11dc5f03) DHCPREQUEST of 192.168.1.147 on eth0.3 to 255.255.255.255 port 67 (xid=0x11dc5f03) DHCPOFFER of 192.168.1.147 from 192.168.1.254 DHCPACK of 192.168.1.147 from 192.168.1.254 bound to 192.168.1.147 -- renewal in 1657 seconds. root@ubuntu:~# ip -4 link sh 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000 link/ether 00:0c:29:bc:fc:8b brd ff:ff:ff:ff:ff:ff 18: eth0.1@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN mode DEFAULT group default link/ether 00:00:00:00:00:11 brd ff:ff:ff:ff:ff:ff 19: eth0.2@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN mode DEFAULT group default link/ether 00:00:00:00:00:22 brd ff:ff:ff:ff:ff:ff 20: eth0.3@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN mode DEFAULT group default link/ether 00:00:00:00:00:33 brd ff:ff:ff:ff:ff:ff root@ubuntu:~# ip -4 addr sh 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever 18: eth0.1@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default inet 192.168.1.145/24 brd 192.168.1.255 scope global eth0.1 valid_lft forever preferred_lft forever 19: eth0.2@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default inet 192.168.1.146/24 brd 192.168.1.255 scope global eth0.2 valid_lft forever preferred_lft forever 20: eth0.3@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UNKNOWN group default inet 192.168.1.147/24 brd 192.168.1.255 scope global eth0.3 valid_lft forever preferred_lft forever root@ubuntu:~# ip -4 route sh default via 192.168.1.254 dev eth0.1 192.168.1.0/24 dev eth0.1 proto kernel scope link src 192.168.1.145 192.168.1.0/24 dev eth0.2 proto kernel scope link src 192.168.1.146 192.168.1.0/24 dev eth0.3 proto kernel scope link src 192.168.1.147 root@ubuntu:~# arping -c 5 -I eth0.1 192.168.1.254 ARPING 192.168.1.254 from 192.168.1.145 eth0.1 Unicast reply from 192.168.1.254 [58:98:35:57:a0:70] 6.936ms Unicast reply from 192.168.1.254 [58:98:35:57:a0:70] 2.986ms Unicast reply from 192.168.1.254 [58:98:35:57:a0:70] 0.654ms Unicast reply from 192.168.1.254 [58:98:35:57:a0:70] 5.137ms Unicast reply from 192.168.1.254 [58:98:35:57:a0:70] 2.426ms Sent 5 probes (1 broadcast(s)) Received 5 response(s) root@ubuntu:~# arping -c 5 -I eth0.2 192.168.1.254 ARPING 192.168.1.254 from 192.168.1.146 eth0.2 Unicast reply from 192.168.1.254 [58:98:35:57:a0:70] 5.665ms Unicast reply from 192.168.1.254 [58:98:35:57:a0:70] 3.753ms Unicast reply from 192.168.1.254 [58:98:35:57:a0:70] 16.500ms Unicast reply from 192.168.1.254 [58:98:35:57:a0:70] 3.287ms Unicast reply from 192.168.1.254 [58:98:35:57:a0:70] 32.438ms Sent 5 probes (1 broadcast(s)) Received 5 response(s) root@ubuntu:~# arping -c 5 -I eth0.3 192.168.1.254 ARPING 192.168.1.254 from 192.168.1.147 eth0.3 Unicast reply from 192.168.1.254 [58:98:35:57:a0:70] 4.422ms Unicast reply from 192.168.1.254 [58:98:35:57:a0:70] 2.429ms Unicast reply from 192.168.1.254 [58:98:35:57:a0:70] 2.321ms Unicast reply from 192.168.1.254 [58:98:35:57:a0:70] 40.423ms Unicast reply from 192.168.1.254 [58:98:35:57:a0:70] 2.268ms Sent 5 probes (1 broadcast(s)) Received 5 response(s) root@ubuntu:~# tcpdump -n -i eth0.1 -v & [1] 5317 root@ubuntu:~# ping -c5 -q -I eth0.1 192.168.1.254 PING 192.168.1.254 (192.168.1.254) from 192.168.1.145 eth0.1: 56(84) bytes of data. tcpdump: listening on eth0.1, link-type EN10MB (Ethernet), capture size 65535 bytes 13:18:37.612558 IP (tos 0x0, ttl 64, id 2595, offset 0, flags [DF], proto ICMP (1), length 84) 192.168.1.145 > 192.168.1.254: ICMP echo request, id 5318, seq 2, length 64 13:18:37.618864 IP (tos 0x68, ttl 64, id 14493, offset 0, flags [none], proto ICMP (1), length 84) 192.168.1.254 > 192.168.1.145: ICMP echo reply, id 5318, seq 2, length 64 13:18:37.743650 ARP, Ethernet (len 6), IPv4 (len 4), Request who-has 192.168.1.87 tell 192.168.1.86, length 46 13:18:38.134997 IP (tos 0x0, ttl 128, id 23547, offset 0, flags [none], proto UDP (17), length 229) 192.168.1.86.138 > 192.168.1.255.138: NBT UDP PACKET(138) 13:18:38.614580 IP (tos 0x0, ttl 64, id 2596, offset 0, flags [DF], proto ICMP (1), length 84) 192.168.1.145 > 192.168.1.254: ICMP echo request, id 5318, seq 3, length 64 13:18:38.793479 IP (tos 0x68, ttl 64, id 14495, offset 0, flags [none], proto ICMP (1), length 84) 192.168.1.254 > 192.168.1.145: ICMP echo reply, id 5318, seq 3, length 64 13:18:39.151282 IP6 (class 0x68, hlim 255, next-header ICMPv6 (58) payload length: 32) fe80::5a98:35ff:fe57:e070 > ff02::1:ff6b:e9b4: [icmp6 sum ok] ICMP6, neighbor solicitation, length 32, who has 2001:818:d812:da00:8ae3:abff:fe6b:e9b4 source link-address option (1), length 8 (1): 58:98:35:57:a0:70 13:18:39.615612 IP (tos 0x0, ttl 64, id 2597, offset 0, flags [DF], proto ICMP (1), length 84) 192.168.1.145 > 192.168.1.254: ICMP echo request, id 5318, seq 4, length 64 13:18:39.746981 IP (tos 0x68, ttl 64, id 14496, offset 0, flags [none], proto ICMP (1), length 84) 192.168.1.254 > 192.168.1.145: ICMP echo reply, id 5318, seq 4, length 64 --- 192.168.1.254 ping statistics --- 5 packets transmitted, 5 received, 0% packet loss, time 4008ms rtt min/avg/max/mdev = 2.793/67.810/178.934/73.108 ms root@ubuntu:~# killall tcpdump >> /dev/null 2>&1 9 packets captured 12 packets received by filter 0 packets dropped by kernel [1]+ Done tcpdump -n -i eth0.1 -v root@ubuntu:~# tcpdump -n -i eth0.2 -v & [1] 5320 root@ubuntu:~# ping -c5 -q -I eth0.2 192.168.1.254 PING 192.168.1.254 (192.168.1.254) from 192.168.1.146 eth0.2: 56(84) bytes of data. tcpdump: listening on eth0.2, link-type EN10MB (Ethernet), capture size 65535 bytes 13:18:41.536874 ARP, Ethernet (len 6), IPv4 (len 4), Reply 192.168.1.254 is-at 58:98:35:57:a0:70, length 46 13:18:41.536933 IP (tos 0x0, ttl 64, id 2599, offset 0, flags [DF], proto ICMP (1), length 84) 192.168.1.146 > 192.168.1.254: ICMP echo request, id 5321, seq 1, length 64 13:18:41.539255 IP (tos 0x68, ttl 64, id 14507, offset 0, flags [none], proto ICMP (1), length 84) 192.168.1.254 > 192.168.1.146: ICMP echo reply, id 5321, seq 1, length 64 13:18:42.127715 ARP, Ethernet (len 6), IPv4 (len 4), Request who-has 192.168.1.87 tell 192.168.1.86, length 46 13:18:42.511725 IP (tos 0x0, ttl 64, id 2600, offset 0, flags [DF], proto ICMP (1), length 84) 192.168.1.146 > 192.168.1.254: ICMP echo request, id 5321, seq 2, length 64 13:18:42.514385 IP (tos 0x68, ttl 64, id 14527, offset 0, flags [none], proto ICMP (1), length 84) 192.168.1.254 > 192.168.1.146: ICMP echo reply, id 5321, seq 2, length 64 13:18:42.743856 ARP, Ethernet (len 6), IPv4 (len 4), Request who-has 192.168.1.87 tell 192.168.1.86, length 46 13:18:43.511727 IP (tos 0x0, ttl 64, id 2601, offset 0, flags [DF], proto ICMP (1), length 84) 192.168.1.146 > 192.168.1.254: ICMP echo request, id 5321, seq 3, length 64 13:18:43.513768 IP (tos 0x68, ttl 64, id 14528, offset 0, flags [none], proto ICMP (1), length 84) 192.168.1.254 > 192.168.1.146: ICMP echo reply, id 5321, seq 3, length 64 13:18:43.637598 IP (tos 0x0, ttl 128, id 23551, offset 0, flags [none], proto UDP (17), length 225) 192.168.1.86.17500 > 255.255.255.255.17500: UDP, length 197 13:18:43.641185 IP (tos 0x0, ttl 128, id 23552, offset 0, flags [none], proto UDP (17), length 225) 192.168.1.86.17500 > 192.168.1.255.17500: UDP, length 197 13:18:43.641201 IP (tos 0x0, ttl 128, id 23553, offset 0, flags [none], proto UDP (17), length 225) 192.168.1.86.17500 > 255.255.255.255.17500: UDP, length 197 13:18:43.743890 ARP, Ethernet (len 6), IPv4 (len 4), Request who-has 192.168.1.87 tell 192.168.1.86, length 46 13:18:44.510758 IP (tos 0x0, ttl 64, id 2602, offset 0, flags [DF], proto ICMP (1), length 84) 192.168.1.146 > 192.168.1.254: ICMP echo request, id 5321, seq 4, length 64 13:18:44.512892 IP (tos 0x68, ttl 64, id 14538, offset 0, flags [none], proto ICMP (1), length 84) 192.168.1.254 > 192.168.1.146: ICMP echo reply, id 5321, seq 4, length 64 13:18:45.510794 IP (tos 0x0, ttl 64, id 2603, offset 0, flags [DF], proto ICMP (1), length 84) 192.168.1.146 > 192.168.1.254: ICMP echo request, id 5321, seq 5, length 64 13:18:45.519701 IP (tos 0x68, ttl 64, id 14539, offset 0, flags [none], proto ICMP (1), length 84) 192.168.1.254 > 192.168.1.146: ICMP echo reply, id 5321, seq 5, length 64 13:18:49.287554 IP6 (class 0x68, hlim 255, next-header ICMPv6 (58) payload length: 32) fe80::5a98:35ff:fe57:e070 > ff02::1:ff6b:e9b4: [icmp6 sum ok] ICMP6, neighbor solicitation, length 32, who has 2001:818:d812:da00:8ae3:abff:fe6b:e9b4 source link-address option (1), length 8 (1): 58:98:35:57:a0:70 13:18:50.013463 IP (tos 0x0, ttl 255, id 50737, offset 0, flags [DF], proto UDP (17), length 73) 192.168.1.146.5353 > 224.0.0.251.5353: 0 [2q] PTR (QM)? _ipps._tcp.local. PTR (QM)? _ipp._tcp.local. (45) 13:18:50.218874 IP6 (class 0x68, hlim 255, next-header ICMPv6 (58) payload length: 32) fe80::5a98:35ff:fe57:e070 > ff02::1:ff6b:e9b4: [icmp6 sum ok] ICMP6, neighbor solicitation, length 32, who has 2001:818:d812:da00:8ae3:abff:fe6b:e9b4 source link-address option (1), length 8 (1): 58:98:35:57:a0:70 13:18:51.129961 IP6 (class 0x68, hlim 255, next-header ICMPv6 (58) payload length: 32) fe80::5a98:35ff:fe57:e070 > ff02::1:ff6b:e9b4: [icmp6 sum ok] ICMP6, neighbor solicitation, length 32, who has 2001:818:d812:da00:8ae3:abff:fe6b:e9b4 source link-address option (1), length 8 (1): 58:98:35:57:a0:70 13:18:52.197074 IP6 (hlim 255, next-header UDP (17) payload length: 53) 2001:818:d812:da00:200:ff:fe00:22.5353 > ff02::fb.5353: [udp sum ok] 0 [2q] PTR (QM)? _ipps._tcp.local. PTR (QM)? _ipp._tcp.local. (45) 13:18:54.128240 ARP, Ethernet (len 6), IPv4 (len 4), Request who-has 192.168.1.87 tell 192.168.1.86, length 46 --- 192.168.1.254 ping statistics --- 5 packets transmitted, 0 received, 100% packet loss, time 4000ms root@ubuntu:~# killall tcpdump >> /dev/null 2>&1 13:18:54.657731 IP6 (class 0x68, hlim 255, next-header ICMPv6 (58) payload length: 32) fe80::5a98:35ff:fe57:e070 > ff02::1:ff6b:e9b4: [icmp6 sum ok] ICMP6, neighbor solicitation, length 32, who has 2001:818:d812:da00:8ae3:abff:fe6b:e9b4 source link-address option (1), length 8 (1): 58:98:35:57:a0:70 13:18:54.743174 ARP, Ethernet (len 6), IPv4 (len 4), Request who-has 192.168.1.87 tell 192.168.1.86, length 46 25 packets captured 26 packets received by filter 0 packets dropped by kernel [1]+ Done tcpdump -n -i eth0.2 -v root@ubuntu:~# tcpdump -n -i eth0.3 icmp & [1] 5324 root@ubuntu:~# ping -c5 -q -I eth0.3 192.168.1.254 PING 192.168.1.254 (192.168.1.254) from 192.168.1.147 eth0.3: 56(84) bytes of data. tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth0.3, link-type EN10MB (Ethernet), capture size 65535 bytes 13:18:56.373434 IP 192.168.1.147 > 192.168.1.254: ICMP echo request, id 5325, seq 1, length 64 13:18:57.372116 IP 192.168.1.147 > 192.168.1.254: ICMP echo request, id 5325, seq 2, length 64 13:18:57.381263 IP 192.168.1.254 > 192.168.1.147: ICMP echo reply, id 5325, seq 2, length 64 13:18:58.371141 IP 192.168.1.147 > 192.168.1.254: ICMP echo request, id 5325, seq 3, length 64 13:18:58.373275 IP 192.168.1.254 > 192.168.1.147: ICMP echo reply, id 5325, seq 3, length 64 13:18:59.371165 IP 192.168.1.147 > 192.168.1.254: ICMP echo request, id 5325, seq 4, length 64 13:18:59.373259 IP 192.168.1.254 > 192.168.1.147: ICMP echo reply, id 5325, seq 4, length 64 13:19:00.371211 IP 192.168.1.147 > 192.168.1.254: ICMP echo request, id 5325, seq 5, length 64 13:19:00.373278 IP 192.168.1.254 > 192.168.1.147: ICMP echo reply, id 5325, seq 5, length 64 --- 192.168.1.254 ping statistics --- 5 packets transmitted, 1 received, 80% packet loss, time 4001ms rtt min/avg/max/mdev = 13.666/13.666/13.666/0.000 ms root@ubuntu:~# killall tcpdump >> /dev/null 2>&1 9 packets captured 10 packets received by filter 0 packets dropped by kernel [1]+ Done tcpdump -n -i eth0.3 icmp root@ubuntu:~# arp -n Address HWtype HWaddress Flags Mask Iface 192.168.1.254 ether 58:98:35:57:a0:70 C eth0.1 192.168.1.254 ether 58:98:35:57:a0:70 C eth0.2 192.168.1.254 ether 58:98:35:57:a0:70 C eth0.3

  Read the article

• Perl DBD::DB2 installation failed

  - by prabhu

  Hi, We dont have root access in our local machine. I installed DBI package first and then installed DBD package. I got the below error first, In file included from DB2.h:22, from DB2.xs:7: dbdimp.h:10:22: dbivport.h: No such file or directory Then I included the DBI path in the Makefile and then I am getting the below error. DB2.xs: In function `XS_DBD__DB2__db_disconnect': DB2.xs:128: error: structure has no member named `_old_cached_kids' DB2.xs:129: error: structure has no member named `_old_cached_kids' DB2.xs:130: error: structure has no member named `_old_cached_kids' DB2.xs: In function `XS_DBD__DB2__db_DESTROY': DB2.xs:192: error: structure has no member named `_old_cached_kids' DB2.xs:193: error: structure has no member named `_old_cached_kids' DB2.xs:194: error: structure has no member named `_old_cached_kids' The versions I am trying to install are DBI-1.610_90.tar.gz DBD-DB2-1.78.tar.gz I am using perl Makefile.PL PREFIX=/home/prabhu/perl_pm/lib The output for perl -V is as follows: Summary of my perl5 (revision 5 version 8 subversion 5) configuration: Platform: osname=linux, osvers=2.4.21-27.0.2.elsmp, archname=i386-linux-thread-multi uname='linux decompose.build.redhat.com 2.4.21-27.0.2.elsmp #1 smp wed jan 12 23:35:44 est 2005 i686 i686 i386 gnulinux ' config_args='-des -Doptimize=-O2 -g -pipe -m32 -march=i386 -mtune=pentium4 -Dversion=5.8.5 -Dmyhostname=localhost -Dperladmin=root@localhost -Dcc=gcc -Dcf_by=Red Hat, Inc. -Dinstallprefix=/usr -Dprefix=/usr -Darchname=i386-linux -Dvendorprefix=/usr -Dsiteprefix=/usr -Duseshrplib -Dusethreads -Duseithreads -Duselargefiles -Dd_dosuid -Dd_semctl_semun -Di_db -Ui_ndbm -Di_gdbm -Di_shadow -Di_syslog -Dman3ext=3pm -Duseperlio -Dinstallusrbinperl -Ubincompat5005 -Uversiononly -Dpager=/usr/bin/less -isr -Dinc_version_list=5.8.4 5.8.3 5.8.2 5.8.1 5.8.0' hint=recommended, useposix=true, d_sigaction=define usethreads=define use5005threads=undef useithreads=define usemultiplicity=define useperlio=define d_sfio=undef uselargefiles=define usesocks=undef use64bitint=undef use64bitall=undef uselongdouble=undef usemymalloc=n, bincompat5005=undef Compiler: cc='gcc', ccflags ='-D_REENTRANT -D_GNU_SOURCE -DDEBUGGING -fno-strict-aliasing -pipe -I/usr/local/include -D_LARGEFILE_SOURCE -D_FILE_OFFSET_BITS=64 -I/usr/include/gdbm', optimize='-O2 -g -pipe -m32 -march=i386 -mtune=pentium4', cppflags='-D_REENTRANT -D_GNU_SOURCE -DDEBUGGING -fno-strict-aliasing -pipe -I/usr/local/include -I/usr/include/gdbm' ccversion='', gccversion='3.4.4 20050721 (Red Hat 3.4.4-2)', gccosandvers='' intsize=4, longsize=4, ptrsize=4, doublesize=8, byteorder=1234 d_longlong=define, longlongsize=8, d_longdbl=define, longdblsize=12 ivtype='long', ivsize=4, nvtype='double', nvsize=8, Off_t='off_t', lseeksize=8 alignbytes=4, prototype=define Linker and Libraries: ld='gcc', ldflags =' -L/usr/local/lib' libpth=/usr/local/lib /lib /usr/lib libs=-lnsl -lgdbm -ldb -ldl -lm -lcrypt -lutil -lpthread -lc perllibs=-lnsl -ldl -lm -lcrypt -lutil -lpthread -lc libc=/lib/libc-2.3.4.so, so=so, useshrplib=true, libperl=libperl.so gnulibc_version='2.3.4' Dynamic Linking: dlsrc=dl_dlopen.xs, dlext=so, d_dlsymun=undef, ccdlflags='-Wl,-E -Wl,-rpath,/usr/lib/perl5/5.8.5/i386-linux-thread-multi/CORE' cccdlflags='-fPIC', lddlflags='-shared -L/usr/local/lib' Characteristics of this binary (from libperl): Compile-time options: DEBUGGING MULTIPLICITY USE_ITHREADS USE_LARGE_FILES PERL_IMPLICIT_CONTEXT Built under linux Compiled at Aug 2 2005 04:48:47 %ENV: PERL5LIB=":/opt/india/dev/perl/XML-XPath-1.13/lib/perl5:/opt/india/dev/perl/XML-XPath- 1.13/lib/perl5/site_perl:/opt/india/dev/perl/XML-XPath-1.13/lib/perl5:/opt/india/dev/perl/XML-XPath-1.13/lib/perl5/site_perl" Could anyone help me to resolve this issue? Appreciate help in advance. Prabhu

  Read the article

< Previous Page | 103 104 105 106 107 108 109 110 111 112 113 114  | Next Page >