Search Results

Search found 20188 results on 808 pages for 'wireless network'.

Page 107/808 | < Previous Page | 103 104 105 106 107 108 109 110 111 112 113 114  | Next Page >

• Speed Problem with Wireless Connectivity on Cisco 877w

  - by Carl Crawley

  Having a bit of a weird one with my local LAN setup. I recently installed a Cisco 877W router on my DSL2+ connection and all is working really well.. Upgraded the IOS to 12.4 and my wired clients are streaming connectivity superfast at 1.3mb/s. However, there seems to be an issue with my wireless clients - I can't seem to stream any data across the local wireless connection (LAN) and using the Internet, whilst responsive enough isn't really comparable with the wired connection speed. For example, all devices are connected to an 8 Port Gb switch on FE0 from the Router with a NAS disk and on my wired clients, I can transfer/stream etc absolutely fine - however, transferring a local 700Mb file on my local LAN estimates 7-8 hours to transfer :( The Wireless config is as follows : interface Dot11Radio0 description WIRELESS INTERFACE no ip address ! encryption mode ciphers tkip ! ssid [MySSID] ! speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 channel 2462 station-role root rts threshold 2312 world-mode dot11d country GB indoor bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 spanning-disabled bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding All devices are connected to the Gb Switch which is connected to FE0 with the following: Hardware is Fast Ethernet, address is 0021.a03e.6519 (bia 0021.a03e.6519) Description: Uplink to Switch MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s ARP type: ARPA, ARP Timeout 04:00:00 Last input never, output never, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 14000 bits/sec, 19 packets/sec 5 minute output rate 167000 bits/sec, 23 packets/sec 177365 packets input, 52089562 bytes, 0 no buffer Received 919 broadcasts, 0 runts, 0 giants, 0 throttles 260 input errors, 260 CRC, 0 frame, 0 overrun, 0 ignored 0 input packets with dribble condition detected 156673 packets output, 106218222 bytes, 0 underruns 0 output errors, 0 collisions, 2 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out Not sure why I'm having problems on the wireless and I've reached the end of my Cisco knowledge... Thanks for any pointers! Carl

  Read the article

• Wireless AAA for a small, bandwidth-limited hotel.

  - by Anthony Hiscox

  We (the tech I work with and myself) live in a remote northern town where Internet access is somewhat of a luxury, and bandwidth is quite limited. Here, overage charges ranging from few hundreds, to few thousands of dollars a month, is not uncommon. I myself incur regular monthly charges just through my regular Internet usage at home (I am allowed 10G for $60CAD!) As part of my work, I have found myself involved with several hotels that are feeling this. I know that I can come up with something to solve this problem, but I am relatively new to system administration and I don't want my dreams to overcome reality. So, I pass these ideas on to you, those with much more experience than I, in hopes you will share some of your thoughts and concerns. This system must be cost effective, yes the charges are high here, but the trust in technology is the lowest I've ever seen. Must be capable of helping client reduce their usage (squid) Allow a limited (throughput and total usage) amount of free Internet, as this is often franchise policy. Allow a user to track their bandwidth usage Allow (optional) higher speed and/or usage for an additional charge. This fee can be obtained at the front desk on checkout and should not require the use of PayPal or Credit Card. Unfortunately some franchises have ridiculous policies that require the use of a third party remote service to authenticate guests to your network. This means WPA is out, and it also means that I do not auth before Internet usage, that will be their job. However, I do require the ABILITY to perform authentication for Internet access if a hotel does not have this policy. I will still have to track bandwidth (under a guest account by default) and provide the same limiting, however the guest often will require a complete 'unlimited' access, in terms of existence, not throughput. Provide firewalling capabilities for hotels that have nothing, Office, and Guest network segregation (some of these guys are running their office on the guest network, with no encryption, and a simple TOS to get on!) Prevent guests from connecting to other guests, however provide a means to allow this to happen. IE. Each guest connects to a page and allows the other guest, this writes a iptables rule (with python-netfilter) and allows two rooms to play a game, for instance. My thoughts on how to implement this. One decent box (we'll call it a router now) with a lot of ram, and 3 NIC's: Internet Office Guests (AP's + In Room Ethernet) Router Firewall Rules Guest can talk to router only, through which they are routed to where they need to go, including Internet services. Office can be used to bridge Office to Internet if an existing solution is not in place, otherwise, it simply works for a network accessible web (webmin+python-webmin?) interface. Router Software: OpenVZ provides virtualization for a few services I don't really trust. Squid, FreeRADIUS and Apache. The only service directly accessible to guests is Apache. Apache has mod_wsgi and django, because I can write quickly using django and my needs are low. It also potentially has the FreeRADIUS mod, but there seems to be some caveats with this. Firewall rules are handled on the router with iptables. Webmin (or a custom django app maybe) provides abstracted control over any features that the staff may need to access. Python, if you haven't guessed it's the language I feel most comfortable in, and I use it for almost everything. And finally, has this been done, is it a overly massive project not worth taking on for one guy, and/or is there some tools I'm missing that could be making my life easier? For the record, I am fairly good with Python, but not very familiar with many other languages (I can struggle through PHP, it's a cosmetic issue there). I am also an avid linux user, and comfortable with config files and command line. Thank you for your time, I look forward to reading your responses. Edit: My apologies if this is not a Q&A in the sense that some were expecting, I'm just looking for ideas and to make sure I'm not trying to do something that's been done. I'm looking at pfSense now as a possible start for what I need.

  Read the article

• Configuring Wireless on Cisco 851W

  - by Aequitarum Custos

  Either a powersurge or something caused our router's configuration to get wiped, and our last backup was before the wireless network was setup. We have not been able to reconfigure the wireless since then, so was curious if anyone here would be able to determine what configuration is needed. We are using a Cisco 851W running 12.4(15)T9 We would like to use WPA encryption, and have it on the same network as the rest of the office network. Config file is below: User Access Verification Building configuration... Current configuration : 3857 bytes ! version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec service password-encryption no service dhcp ! hostname BOB ! boot-start-marker boot-end-marker ! enable secret 5 ********************* ! no aaa new-model ! ! dot11 syslog no ip source-route ! ! ip cef no ip bootp server ip domain name BOB.com ip name-server 61.11.1.1 ip name-server 61.11.1.2 ! ! ! username BOBB privilege 15 password 7 ************************* ! ! archive log config hidekeys ! ! ip tcp synwait-time 10 ! ! ! interface FastEthernet0 no cdp enable ! interface FastEthernet1 no cdp enable ! interface FastEthernet2 no cdp enable ! interface FastEthernet3 no cdp enable ! interface FastEthernet4 description WAN Connection$ETH-WAN$ ip address 61.11.1.14 255.255.254.0 ip nat outside ip virtual-reassembly duplex auto speed auto no cdp enable ! interface Dot11Radio0 no ip address shutdown ! encryption mode ciphers tkip speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0 station-role root no cdp enable ! interface Dot11Radio0.1 encapsulation dot1Q 1 native no cdp enable bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 spanning-disabled bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding ! interface Dot11Radio0.20 ip access-group Guest-ACL in no cdp enable ! interface Vlan1 description Internal Network ip address 192.168.2.60 255.255.255.0 ip nat inside ip nat enable ip virtual-reassembly ! ip forward-protocol nd ip route 0.0.0.0 0.0.0.0 61.11.2.14 ! ip http server no ip http secure-server ip nat inside source list 1 interface FastEthernet4 overload ! ip access-list extended Guest-ACL deny ip any 192.0.0.0 0.0.0.255 permit ip any any ! access-list 1 permit 192.0.0.0 0.0.0.255 access-list 100 remark SDM_ACL Category=2 access-list 100 permit ip 192.0.0.0 0.0.0.255 any no cdp run ! control-plane ! !

  Read the article

• Samba share not accessible from Win 7 - tried advice on superuser

  - by Roy Grubb

  I have an old Red Hat Linux box that I use, amongst other things, to run Samba. My Vista and remaining Win XP PC can access the p/w-protected Samba shares. I just set up a new Windows 7 64-bit Pro PC. Attempts to access the Samba shares by clicking on the Linux box's icon in 'Network' from this machine gave a Logon failure: unknown user name or bad password. message when I gave the correct credentials. So I followed the suggestions in Windows 7, connecting to Samba shares (also checked here but found LmCompatibilityLevel was already 1). This got me a little further. If click on the Linux box's icon in 'Network' from this machine I now see icons for the shared directories. But when I click on one of these, I get \\LX\share is not accessible. You might not have permission... etc. I tried making the Win 7 password the same as my Samba p/w (the user name was already the same). Same result. The Linux box does part of what I need for ecommerce - the in-house part, it's not accessible to the Internet. As my Linux Fu is weak, I have to avoid changes to the Linux box, so I'm hoping someone can tell me what to do to Win 7 to make it behave like XP and Vista when accessing this share. Help please!? Thanks Thanks for replying @Randolph. I had set 'Network security: LAN Manager authentication level' to Send LM & NTLM - use NTLMv2 session security if negotiated based on the advice in Windows 7, connecting to Samba shares and had restarted the machine, but that didn't work for me. I'll try playing with other Network security values. I have now tried the following: Network security: Allow Local System to use computer identity for NTLM: changed from Not Defined to "Enabled". Restarted machine Still says "\LX\share is not accessible. You might not have permission..." etc. Network security: Restrict NTLM: Add remote server exceptions for NTLM Authentication (added LX) Restarted machine Still says "\LX\share is not accessible. You might not have permission..." etc. I can't see any other Network security settings that might affect this. Any other ideas please? Thanks Roy

  Read the article

• Cannot Import VPN connection

  - by ECII

  Since 12.04 I cannot connect to my VPN. my ovpn file is the following http://email.uoa.gr/help/download/vpn/edunet.ovpn When I try to import the VPN file i get the following error The file 'edunet.ovpn' could not be read or does not contain recognized VPN connection information Error: unknown PPTP file extension. Is there any way arround this error? I have already installed network-manager-openvpn

  Read the article

• Ceph: open-source petabyte scale distributed storage

  - by Gregory Burd

  You might want to read this interesting research paper titled "Object Storage on Berkeley DB". The Ceph project is a distributed network file system designed to provide excellent performance, reliability, and scalability... and it uses Oracle Berkeley DB for storage.

  Read the article

• Out-of-the-Box Spatial Dashboards Improve Utility Outage Decisions

  - by stephen.garth

  Oracle Utilities Advanced Spatial Outage Analytics leverages the capabilities of Oracle Business Intelligence with map visualization and geospatial analysis of outage data from utility network management systems, providing BI dashboards to support utility executives and other decision makers throughout the enterprise. This excellent article by Oracle's Guerry Waters, published by Directions Media, gives details. Read the article here. Get more information: - Oracle Spatial - Oracle Utilities - Oracle Business Intelligence

  Read the article

• Wvdial randomly drops 3G connection - How to auto-reconnect?

  - by askvictor

  I'm using a 3G modem for a router running Ubuntu server 10.04. I have the connection established using wvdial, which works successfully, but sometimes the connection drops. I would like it to auto re-connect. I've set the "auto reconnect" in wvdial.conf, but this does not seem to work. Any ideas? Am I missing a config option, or should I try writing a script which polls the network status and resets if ppp0 has gone down?

  Read the article

• Setting up Ubuntu Server as a Router with DHCPD and 3 Ethernet devices

  - by cengbrecht

  My configuration: Ubuntu 12.04 DHCP3-server eth0, eth1, eth2 Edit: removed br0&br1 eth0 is the external connection eth1 & eth2 are the internal network eth1 and eth2 are supposed to be seperate networks of student/teachers respectivly. What I would like to have is the internet from external device bridged to device 1 and 2, with the DHCP server controlling the two internal devices. Its already working with DHCP, the part I am stuck on is bridging for internet. I have setup a script that I found here: Router With the original script he linked here: Ubuntu Router Guide echo -e "\n\nLoading simple rc.firewall-iptables version $FWVER..\n" IPTABLES=/sbin/iptables #IPTABLES=/usr/local/sbin/iptables DEPMOD=/sbin/depmod MODPROBE=/sbin/modprobe EXTIF="eth0" INTIF="eth1" INTIF2="eth2" echo " External Interface: $EXTIF" echo " Internal Interface: $INTIF" echo " Internal Interface: $INTIF2" EXTIP=`ifconfig $EXTIF | grep 'inet addr:' | sed 's#.*inet addr\:\([0-9]\{1,3\}\.[0-9]\{1,3\}\.[0-9]\{1,3\}\.[0-9]\{1,3\}\).*#\1#g'` echo " External IP: $EXTIP" #====================================================================== #== No editing beyond this line is required for initial MASQ testing == The rest of the script below this is as is. I can get ip from the eth1 & eth2 devices, and my computer can see them, and them it, however, internet is not being passed through. If you need more information please just let me know. EDIT: So I had a 255.255.254.0 network, I believe that was causing the issue. Not sure if it will matter on the second card, I will test later. After changing the subnet to 255.255.255.0 the pings will pass through, however, I cannot get DNS requests to pass? My new Config for Firewall Rules # /etc/iptables.up.rules # Generated by iptables-save v1.4.12 on Wed Nov 28 19:43:28 2012 *mangle :PREROUTING ACCEPT [39:4283] :INPUT ACCEPT [39:4283] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [12:4884] :POSTROUTING ACCEPT [13:5145] COMMIT # Completed on Wed Nov 28 19:43:28 2012 # Generated by iptables-save v1.4.12 on Wed Nov 28 19:43:28 2012 *filter :FORWARD ACCEPT [0:0] :INPUT ACCEPT [0:0] :OUTPUT ACCEPT [0:0] -A FORWARD -j LOG -A FORWARD -m state -i eth1 -o eth0 --state NEW,ESTABLISHED,RELATED -j ACCEPT -A FORWARD -m state -i eth2 -o eth0 --state NEW,ESTABLISHED,RELATED -j ACCEPT -A FORWARD -m state -i eth0 -o eth1 --state NEW,ESTABLISHED,RELATED -j ACCEPT -A FORWARD -m state -i eth0 -o eth2 --state NEW,ESTABLISHED,RELATED -j ACCEPT COMMIT # Completed on Wed Nov 28 19:43:28 2012 # Generated by iptables-save v1.4.12 on Wed Nov 28 19:43:28 2012 *nat :INPUT ACCEPT [0:0] :PREROUTING ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] -A POSTROUTING -o eth0 -j MASQUERADE -A POSTROUTING -o eth0 -j SNAT --to-source 192.168.1.25 COMMIT # Completed on Wed Nov 28 19:43:28 2012 Not sure what else you may need, but I am using Webmin to control the server(Needed for the operators on site to know how to use it.) If you could explain it as standard CLI commands, or edits to this file directly then we should be ok. :) And thanks again Erik, I do believe your edits did help.

  Read the article

• How can I force a USB modem to only connect via EDGE and not 3G?

  - by Anders Wallenquist

  How do I get Network-admin to restrict connection to GSM (Edge) instead of flipping between 3G and Edge and lose connection. Usually it works out-of-the box, but at my current location there are a lot of radio shadows, so the recommendation from my ISP is that I should lock to Edge - which can be done using their own driver in Windows. How can I do this in Ubuntu Ubuntu 11.04 Modem: Huawei E220 ISP: Telia mobilt bredband kontant

  Read the article

• Can a Windows computer access Pulse sound server on an Ubuntu computer?

  - by Dave M G

  With help I received in this question, I set up all my Ubuntu computers so that they all access a central computer for sound output, using Pulse Audio Preferences. I have some Windows computers as well. I was wondering if it is also possible to make them clients of the sound server computer, so that they will send their sound output over the network to be played by the Ubuntu computer running the Pulse audio sound server. And if so, how?

  Read the article

• Many network adapters at machine, need to find one that is used for traffic in Windows (from .net)

  - by viko

  My application use Web-service. I'm control from what workstation was request and for this send MAC-Address how parameter of all methods. But then I start testing application in real, I found workstations which have many network adapters - Ethernet, Wireless, Bluetooth. When I get MAC-address using next code: var networkAdapters = NetworkInterface.GetAllNetworkInterfaces(); if (networkAdapters == null || networkAdapters.Length == 0) return string.Empty; string address = string.Empty; foreach (var adapter in networkAdapters) { var a = adapter.GetPhysicalAddress(); if (a != null && a.ToString() != string.Empty) { address = a.ToString(); break; } } return address; Sometimes Web-service receive from workstation different MAC-Addresses, but I want get always only one MAC-address. Please, help me.

  Read the article

• Wireless does not work on Ubuntu 9.04

  - by Yongwei Xing

  Hi all I install the Ubuntu 9.04 my old Lenovo Y520 laptop, the wirless does not work.My Wireless card is Intel Pro/wireless 2100 card. But I can not enable it. My wired card is working well. Does anyone meet it before. the ifconfig output is eth0 Link encap:Ethernet HWaddr 00:0a:e4:5f:6c:30 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:973 errors:0 dropped:0 overruns:0 frame:0 TX packets:1025 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:574701 (574.7 KB) TX bytes:169249 (169.2 KB) Interrupt:10 eth1 Link encap:Ethernet HWaddr 00:0c:f1:58:79:b5 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:10 Base address:0x8000 Memory:d0202000-d0202fff lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B) the output of iwconfig is eth1 unassociated ESSID:off/any Nickname:"ipw2100" Mode:Managed Channel=0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:off Retry short limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I have another question. When my OS is 9.04, there is a icon about network connection on the panel at the top. After I upgraded to 9.10, that icon disappeared. How can I get that back? Best Regareds,

  Read the article

• unable to access Internet by wireless but can by cable

  - by Jeff King

  i'M GOING MAD! UNtil last friday I had been successfully using wifi with the supplier as VIRGIN through their Motorola SB 4200 cable Modem and the wireless router being the Linksys WRT 54G router. Supported were three lap tops and an EPSON 510W printer and this had been running with no issue for about 3 years. Back to last friday, we started suffering significant delays and then the network collapsed with no wireless access. I was able to connect a single laptop direct to the cable modem and internet access was restored to just that one device. I thought that the problem was the router so I tried a backup D-Link device with no success. I have subsequently bought another cable modem AND a netgear router plus addidtional ethernet cables but with no success. The best that happens is that the signal appears good but I cannot get access to the internet. A yellow question mark appears on the 'gradient' icon. Each laptop and router works elsewhere so I'm stumped. Mind you I am a real novice so I'm not surprised. Please can anyone tell me what I'm doing wrong?

  Read the article

• wireless clients not getting correct dhcp addresses

  - by szeli

  I apologise first if this is a stupid problem. I'm new to Cisco networking. I need some help with an existing configuration done by my vendor. Environment: 1. Core switch - Catalyst 6509e vlans configured: a. vlan 50 (wired clients) 10.0.50.x/24 interface IP 10.0.50.20 b. vlan 70 (wireless clients) 10.0.70.x/24 interface IP 10.0.70.20 c. vlan 192 (guest clients) 192.168.1.x/24 interface IP 192.168.1.20 d. trunk port for WLC native vlan 70 allowed vlan 50, 70, 192 2. Cisco 4402 WLC interfaces a. management untagged IP 10.0.70.10 b. ap-manager untagged IP 10.0.70.11 c. service-port n/a IP 192.168.10.1 d. virtual n/a IP 1.1.1.1 e. guestwlan vlan192 IP 192.168.1.100 3. Cisco AIR-LAP1142N-S-K9 LAP01 (WLAN local, interface: management) IP 10.0.70.21/24 GW 10.0.70.20 DHCP server 10.0.50.10 (scope 10.0.70.101 to 200) LAP02 (WLAN guest, interface: guestwlan) IP 192.168.1.21/24 GW 192.168.1.20 DHCP server 192.168.1.10 (scope 192.168.1.101 to 200) here's the problem, wireless clients connected to WLAN guest keep getting DHCP leases from WLAN local 10.0.50.10 (scope 10.0.70.101 to 200) can anyone please help? thanks!

  Read the article

• Virtual Wifi Issue Windows 7

  - by Matt

  Lately I've been trying to use my laptop as a wireless router in my room. I have it connected to my school's network through ethernet, and I want to set up wireless so that I can use Wifi on my Android phone and iPod Touch. In the past, I used Connectify, but I started having an issue where my phone would find the network, connect, attempt to get the IP, and then suddenly the network would disappear. Then it'd pop up again, and the same process would happen over and over. I decided that I'd totally uninstall Connectify, but after that, neither Virtual Router Manager nor the command prompt could create a viable network either. My phone and even my iPod now encounter the same problem. Neither can successfully connect. So evidently there is something wrong with the laptop's virtual wifi feature, and I have no idea what that could be. I've tried enabling certain services that virtual wifi supposedly relies on, but some of them don't start, namely Remote Access Connection Manager. But I also have read that these enable on their own and that if they are normally not enabled it's fine. Furthermore, I even uninstalled and reinstalled the drivers for my wireless card. Any ideas as to why my virtual wifi won't function? Anything? I really would love to get this working...

  Read the article

• Turning on Bluetooth disables wifi on Yoga 2

  - by Yostage

  I have a Lenovo Yoga 2. The moment that I turn on bluetooth, the wifi drops out - I lose connection, and connecting again shows "connection failed". If I turn the bluetooth off, wifi can reestablish fine. I've tried lots of different combinations of drivers for both the wifi and the bluetooth, but no combination has has changed this behavior yet. I've read some speculation that the cards have insufficient shielding, but that seems like kind of a large flaw to ship with. I've tried with a Carbon X1, a Yoga 2 Pro, and a Yoga 2 all next to each other on the desk while running InSSIDer. The X1 and the Y2P don't lose wifi connection when the bluetooth turns on, but the Y2 does immediately. The Y2P and the Y2 are running the same drivers for bluetooth and wifi, and appear to have the same wireless card internally. During the failure state, InSSIDer still sees signal strength for my network, but I cannot connect to it. stats: the card that comes in the laptop is an Intel Wireless-N 7260 Intel Bluetooth driver is at 17.0.1401.422 Intel Wireless driver is at 17.0.2.5 Windows 8.1 x64 Home wifi is a Medialink MWN-WAPR150N

  Read the article

• Number of routers in small community lock up and require reboot.

  - by Anthony Hiscox

  I live in a small town which has one primary ISP. Lately I have noticed that a number of wireless routers have been locking up and requiring a reboot before allowing any connections. This has affected two of my routers, my work router, and a few others. In all cases wired continued to function as usual. Often wireless clients can see the SSID but simply won't connect. I can only think of a few possibilities and was hoping someone here might be able to point me in the right direction: Our ISP is well known to be flaky, something they are doing is causing this, what that might be I have no clue it as seems to affect the wireless only. There's a power issue in town, given our remote location and reputation for crap electrical, this seems reasonable. Only one router was plugged in to a UPS, and I'm not sure of the quality. There is some bug in all the different firmware for every one of these routers (all different). That doesn't seem reasonable, unless; it's an unknown (or known) exploit or DoS of some sort being launched by a massive team of ninjas hell bent on forcing us all to be tethered to our walls by ethernet cables or; it's just been a coincidence and I'm just paranoid (this has some weight, I mean read 4 again). Anyone else experience similar issues and have some tips?

  Read the article

• can't get to admin page after factory reset netgear wg602

  - by stefanB

  I have wireless Netgear wg602 on my home network (connected to my internet modem/router). I've had it secured and locked down to only accept connection from specific MAC addresses. I've forgotten the password that I used but my Mac Book laptops can still connect (multiple OS updates - it can't retrieve and display the password but it can use it to log in to WPA) so I want to reconfigure it from scratch (have some new devices). I tried to reset the Netgear wg602 to factory settings (pressed reset button for 10 sec), reset my laptop IP address to local address suggested in manual (192.168.0.210 net mask 255.255.255.0), connect Netgear via ethernet cable to my mac book pro but I can't get to the admin page at 192.168.0.227 as suggested by manual (firefox or safari). At this stage the Netgear is not connected to router, it is only connected to mac book. I can't ping the wireless access point either (but it is on all lights are on). What am I doing incorrectly? Last time I configured it via Windows now I only have Mac Book (which I've used with the wireless access point for 2 years so no compatibility problems).

  Read the article

• Can Internet data be used by malware when PC off?

  - by Val

  I have noticed over the last month that my off peak data has been used at a rate of approx 350MB per hour - this has meant that I have gone over my quota and slowed down by my ISP to 256k. There is no one in the house using it (2am-8am is my ISPs off peak hours) at that time. My PC and other wireless devices (ipad and iphone) are turned off. I have changed the wireless password on my modem 3 times and it is now 30 digits long. So I don't think someone else is using my wireless access between 2-8am. It has been suggested by my ISP that I may have malware/spyware on my computer. Sorry for my ignorance, but can malware still run if the PC is off? I did look at my modem's log and followed an IP address to a service called Amazon Simple server Storage. Could this company possibly be the culprit? I am not too tech savvy, so any assistance appreciated. I have run a barrage of spyware cleaning software eg malware bytes; spy bot etc.... Cheers Val

  Read the article

• A router that supports connecting with 2 different wifi networks

  - by Allan Deamon

  I Have the following setup in one place: We have a small local ISP through wireless. I have a external parabolic antenna, connected to a external usb wifi radio, connected through USB to a desktop old PC. The pc connects do the ISP wiki network, then do a Dial Up (PPPoE) connection through the this wifi setup. This will expand with others mobiles devices to be used. When I need, I take my home wireless router and connect though Ethernet in the PC, which is shares the internet. The problem is that the PC must be always ON and working. I would like to buy a wireless router which could be an AP to the mobile devices, notebooks, etc, as also could connect to the ISP Wifi/PPPoE network. So, this device must: Have one radio with detachable antenna to connect to the external antenna. It must connect as client to a network and then dial up the PPP Have another radio serving as AP (infrastructure) to the local place This can't be very expensive. I found a candidate: ( http://www.tp-link.com/en/products/details/?categoryid=1682&model=TL-WR2543ND ) It have 3 deatachable antennas, working with dual band. Officially, his firmware doesn't support it. My supposition: If internally there is 3 or 2 distinct wlan ports (like wlan0, wlan1), and there is support, i could use a OpenWRT, DD-WRT or Tomato to make this works. It also have 1 USB port, which I cold use to connect my actual USB Wifi card on it instead to the old PC. Another alternative, is a router that can do this out of box, with the original firmware. But I don't think this is a easy thing to find.

  Read the article

• linux shutdown hang with wifi cifs mounts

  - by Sirex

  Since fedora 15 (and now with 16) it seems that wireless clients take a long while to shutdown when they have network filesystems mounted at shutdown time. I've pushed out a cifs mount via puppet, and all clients have it, including those on wireless. If say a laptop is on a wired connection it shuts down just fine, but if its on the wifi at the time (and no wired connection) it'll hang at the fedora f logo. I'm not sure if its indefinite or just a really long while, but ill give it a test when i shut this machine down in a second. Needless to say its pretty annoying, so is there a way of causing the machine to shutdown even if network connectivity has been lost at unmount time, -- or an official way to reorder events so the wireless card is kept up until after the unmount happens during the shut down process (short of writing a custom script for shutdowns which is a bit of a kludge) ? It does this on multiple machines, and all started doing it when we went from fedora 14 to 15. It was such an obvious issue i'd kind of assumed someone must have reported it or there was an easy fix, but i've not discovered anything yet. Additional info: I can confirm that manually unmounting the mounts then shutting down (sudo shutdown or the xfce shutdown button) will shutdown just fine, it only hangs if the mounts are still mounted The puppet config that sets the mount looks like this (now with the _netdev entry that is indeed pushed to clients successfully, but makes no difference): file { "/mnt/share": ensure = directory,} mount { "/mnt/share": atboot = true, ensure = mounted, remounts = false, fstype = cifs, device = "//srv/share", options = "user,gid=shareusers,uid=${user},file_mode=0700,dir_mode=0700,credentials=/root/.smbcreds,_netdev", require = [ File["/mnt/share"], Group["shareusers"] ], } }

  Read the article

• Is there an easy way to verify that a server exists on a network with VBScript?

  - by Michael Beck

  Hey, I have the eventual goal of determining that a particular database on a particular server with particular credentials is running, but I would settle, at this point, for the ability to check and see if a server is actually up on the network. Does anyone have a way of doing this? I seem to be drawing a blank. Michael

  Read the article

• Ruby - Platform independent way to determine IPs of all network interfaces?

  - by Tindron

  Is there an easy way in Ruby for me to get a list of the IP addresses for all network interfaces? It needs to work in Linux/Win/OSX and I'd prefer to not have to parse ifconfig/ipconfig unless I absolutely have to.

  Read the article

• tutorials about creating a social network using PHP & MySQL ?

  - by Sercan

  Where can I find tutorials about creating a social network (like db structure, sql query samples eg.) using PHP & MySQL ? I do not need a ready script, I just want to learn how to do it..

  Read the article

< Previous Page | 103 104 105 106 107 108 109 110 111 112 113 114  | Next Page >