Search Results

Search found 13183 results on 528 pages for 'sleep mode'.

Page 108/528 | < Previous Page | 104 105 106 107 108 109 110 111 112 113 114 115  | Next Page >

  • usb_modeswitch not switching

    - by deniz
    After I upgraded from kernel 2.6.18 to 3.5.3 modeswitch started not to work for me. Although lsusb shows my usb modem, usb_modeswitch does not switch it. My system information is like below. I ran lsusb, dmesg, usb-devices and usb_modeswitch their output is like below. usb_modeswitch instead of switching my modem it says "No devices in default mode found. Nothing to do. Bye.". Can you offer a solution? Kernel: Linux 3.5.3 usb_modeswitch: 1.2.3-1 usb_modeswitch-data: 20120120-1 usbutils: 006-1 libusb: 1.0.8-0.1 root@localhost$ lsusb Bus 002 Device 029: ID 12d1:1446 Huawei Technologies Co., Ltd. root@localhost$ dmesg [70112.477080] usb 2-1.4: new high-speed USB device number 30 using ehci_hcd [70112.567757] scsi49 : usb-storage 2-1.4:1.0 [70112.567842] scsi50 : usb-storage 2-1.4:1.1 [70113.571433] scsi 49:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2 [70113.572304] scsi 50:0:0:0: Direct-Access HUAWEI TF CARD Storage PQ: 0 ANSI: 2 [70113.574169] sr0: scsi-1 drive [70113.574223] sr 49:0:0:0: Attached scsi CD-ROM sr0 [70113.574250] sr 49:0:0:0: Attached scsi generic sg1 type 5 [70113.574350] sd 50:0:0:0: Attached scsi generic sg2 type 0 [70113.577173] sd 50:0:0:0: [sdb] Attached SCSI removable disk root@localhost$ usb-devices T: Bus=02 Lev=02 Prnt=02 Port=03 Cnt=01 Dev#= 30 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=12d1 ProdID=1446 Rev=00.00 S: Manufacturer=Huawei Technologies S: Product=HUAWEI Mobile C: #Ifs= 2 Cfg#= 1 Atr=c0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage I: If#= 1 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage root@localhost$ cat /etc/usb_modeswitch.d/12d1\:1446 # Huawei, newer modems TargetVendor= 0x12d1 TargetProductList="1001,1406,140b,140c,1412,141b,1433,1436,14ac,1506" MessageContent="55534243123456780000000000000011062000000100000000000000000000" root@localhost$ usb_modeswitch -c /etc/usb_modeswitch.d/12d1:1446 -v 12d1 -p 1446 -W * usb_modeswitch: handle USB devices with multiple modes * Version 1.2.3 (C) Josua Dietze 2012 * Based on libusb0 (0.1.12 and above) ! PLEASE REPORT NEW CONFIGURATIONS ! DefaultVendor= 0x12d1 DefaultProduct= 0x1446 TargetVendor= 0x12d1 TargetProduct= not set TargetClass= not set TargetProductList="1001,1406,140b,140c,1412,141b,1433,1436,14ac,1506" DetachStorageOnly=0 HuaweiMode=0 SierraMode=0 SonyMode=0 QisdaMode=0 GCTMode=0 KobilMode=0 SequansMode=0 MobileActionMode=0 CiscoMode=0 MessageEndpoint= not set MessageContent="55534243123456780000000000000011062000000100000000000000000000" NeedResponse=0 ResponseEndpoint= not set InquireDevice enabled (default) Success check disabled System integration mode disabled usb_set_debug: Setting debugging level to 15 (on) usb_os_find_busses: Skipping non bus directory devices usb_os_find_busses: Skipping non bus directory drivers usb_os_find_busses: Skipping non bus directory uevent usb_os_find_busses: Skipping non bus directory drivers_probe usb_os_find_busses: Skipping non bus directory drivers_autoprobe Looking for target devices ... No devices in target mode or class found Looking for default devices ... No devices in default mode found. Nothing to do. Bye. Thanks in advance.

    Read the article

  • Windows 7 Locks Up or Blue Screens after installing additional hard drive

    - by Ryan
    I've had my home theater pc for over a year now and it's been running with no problems what so ever. I got myself a new Seagate 2 TB hard drive for the holidays and ever since installing it the pc now randomly locks up or blue screens either upon putting it to sleep or waking it from sleep. The only thing I've tried so far is updating the firmware on the hard drive. The hard drive in question is this one (http://www.tigerdirect.com/applications/SearchTools/item-details.asp?EdpNo=4846365). I do have my minidump file saved off on my home theater pc however right now I'm at work and don't have access to it. Please help! Thank you!

    Read the article

  • Getting a black laptop screen

    - by Vivek
    I get a black screen when I boot my laptop. The laptop was in sleep mode initially, so when I pressed the power button, it looked as if it woke up from sleep mode, but the screen was blank. So, I held down the power button to force shutdown the laptop and then removed the battery. But after booting the laptop the screen still remains black. The bios/boot screen remains black as well. I have tried connecting it to external hdmi/vga/s-video devices and booting still no go. Windows loads fine, as I can type the password and get the 'Ding', then alt-f4 and shutdown windows. If it helps, the laptop model is Asus G1S-A1. Thanks in advance!

    Read the article

  • windows vms unpredictibly require login

    - by marrrkus
    I have a cluster of vms on a number of cloned servers using libvirt/qemu. Occassionally the windows 7 vms randomly require a login screen, even though I've done everything I can think of and can google to turn off a login screen. I've used netplwiz to turn off requiring a password (http://pcsupport.about.com/od/windows7/ht/auto-logon-windows-7.htm) manually changed the regsistry using the instructions here: http://superuser.com/a/28654 changed requiring a password in the power saving settings in the control panel if the screen goes to sleep told the screen to never go to sleep (in the control panel) Even with all of these things, some of the vms *still* randomly require a login. I have no idea what else to try. Any ideas??

    Read the article

  • Win Server 2008 Hanging on "Applying Computer Settings"

    - by revoked
    Applied ~8 updates this morning, and on reboot the server just sits on "Applying Computer Settings". I've let it sit for a max of almost 40m with no response. I hard-booted (/duck) and can get into safe-mode. From there it applies it's updates and is ok. But still on normal boot gets stuck in "applying". I've tried uninstalling the updates from safe-mode with the same reaction. Any insights?

    Read the article

  • What is auto-mounting my media volume?

    - by user285277
    Something is repeatedly mounting my "media" share, doing something with it, then quietly un-mounting it with no notifications at the user level. from the little I can gleaned from the console messages below, I thought I'd managed to stop it, if not understand it last night when I followed instructions for deleting all traces of the Google Update Daemon. I've not been using any Google apps whatsoever, so I was surprised to see that in Console. What's more surprising, and perhaps a little distressing, is that the same thing occurred this evening, when the Google Daemon is long gone. I don't have that log because I can't recall precisely what time it occurred. I'll do a search and provide it if you wish, though. In the meantime, any help with this would be extremely appreciated. I've asked over at Apple Discussions but I think it might be a little deeper than those manning the boards this weekend are comfortable with. It's certainly beyond my meager skills. With apologies in advance if this is more lines thank you need. Please note that I've transformed the Google links a little because the forum here requires more reputation points before one can post more than two links. 12/27/13 10:47:31.000 PM kernel[0]: memorystatus_thread: idle exiting pid 53629 [distnoted] 12/27/13 10:48:10.433 PM com.apple.Preview.TrustedBookmarksService[53640]: Failed to resolve bookmark data at index: 0; not stale; error: The file doesn’t exist. 12/27/13 10:48:10.434 PM com.apple.Preview.TrustedBookmarksService[53640]: Failed to resolve bookmark data at index: 1; not stale; error: The file doesn’t exist. 12/27/13 10:48:10.950 PM com.apple.SecurityServer[17]: Session 103257 created 12/27/13 10:48:34.328 PM com.apple.Preview.TrustedBookmarksService[53640]: Failed to resolve bookmark data at index: 2; not stale; error: The file doesn’t exist. 12/27/13 10:48:34.000 PM kernel[0]: AFP_VFS afpfs_mount: /Volumes/Media Archive-1, pid 53641 12/27/13 10:48:34.000 PM kernel[0]: AFP_VFS afpfs_mount : succeeded on volume 0xffffff80d6355008 /Volumes/Media Archive-1 (error = 0, retval = 0) 12/27/13 10:49:32.000 PM kernel[0]: wlEvent: en0 en0 Link DOWN virtIf = 0 12/27/13 10:49:32.000 PM kernel[0]: AirPort: Link Down on en0. Reason 8 (Disassociated because station leaving). 12/27/13 10:49:32.000 PM kernel[0]: en0::IO80211Interface::postMessage bssid changed 12/27/13 10:49:33.681 PM configd[16]: network changed: v4(en0-:10.0.1.12) DNS- Proxy- SMB 12/27/13 10:49:33.697 PM configd[16]: network changed: DNS* Proxy 12/27/13 10:49:35.475 PM KernelEventAgent[57]: tid 00000000 received event(s) VQ_NOTRESP (1) 12/27/13 10:49:35.000 PM kernel[0]: ASP_TCP Disconnect: triggering reconnect by bumping reconnTrigger from curr value 0 on so 0xffffff802176b4a0 12/27/13 10:49:35.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect started /Volumes/Media Archive-1 prevTrigger 0 currTrigger 1 12/27/13 10:49:35.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: doing reconnect on /Volumes/Media Archive-1 12/27/13 10:49:35.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: posting to KEA EINPROGRESS for /Volumes/Media Archive-1 12/27/13 10:49:35.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: Max reconnect time: 600 secs, Connect timeout: 15 secs for /Volumes/Media Archive-1 12/27/13 10:49:35.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: connect to the server /Volumes/Media Archive-1 12/27/13 10:49:35.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: connect on /Volumes/Media Archive-1 failed 65. 12/27/13 10:49:35.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: sleep for 1 seconds and then try again 12/27/13 10:49:35.479 PM KernelEventAgent[57]: tid 00000000 type 'afpfs', mounted on '/Volumes/Media Archive-1', from '//Me@Capsule._afpovertcp._tcp.local/Media%20Archive', not responding 12/27/13 10:49:35.487 PM KernelEventAgent[57]: tid 00000000 found 1 filesystem(s) with problem(s) 12/27/13 10:49:36.692 PM com.bourgeoisbits.cloak.agent[14503]: NetworkProfile: (null), (null), (null) (Connected: NO, Airport: NO, Open: NO) [trusted] 12/27/13 10:49:36.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: connect to the server /Volumes/Media Archive-1 12/27/13 10:49:36.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: connect on /Volumes/Media Archive-1 failed 65. 12/27/13 10:49:36.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: sleep for 2 seconds and then try again 12/27/13 10:49:38.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: connect to the server /Volumes/Media Archive-1 12/27/13 10:49:38.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: connect on /Volumes/Media Archive-1 failed 65. 12/27/13 10:49:38.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: sleep for 4 seconds and then try again 12/27/13 10:49:41.000 PM kernel[0]: CODE SIGNING: cs_invalid_page(0x1000): p=53662[GoogleSoftwareUp] clearing CS_VALID 12/27/13 10:49:42.102 PM GoogleSoftwareUpdateDaemon[53663]: -[KeystoneDaemon logServiceState] GoogleSoftwareUpdate daemon (1.1.0.3659) vending: com.google.Keystone.Daemon.UpdateEngine: 2 connection(s) com.google.Keystone.Daemon.Administration: 0 connection(s) 12/27/13 10:49:42.113 PM GoogleSoftwareUpdateDaemon[53663]: -[KSUpdateEngine updateProductID:] KSUpdateEngine updating product ID: "com.google.Keystone" 12/27/13 10:49:42.116 PM GoogleSoftwareUpdateDaemon[53663]: -[KSCheckAction performAction] KSCheckAction checking 1 ticket(s). 12/27/13 10:49:42.121 PM GoogleSoftwareUpdateDaemon[53663]: -[KSUpdateCheckAction performAction] KSUpdateCheckAction starting update check for ticket(s): {( <KSTicket:0x531870 productID=com.google.Keystone version=1.1.0.3659 xc=<KSPathExistenceChecker:0x5302d0 path=/Library/Google/GoogleSoftwareUpdate/GoogleSoftwareUpdate.bundle/> serverType=Omaha url=htt[PeeEs]://tools.google.com/service/update2 creationDate=2012-08-12 14:47:10 > )} Using server: <KSOmahaServer:0x534340 engine=<KSDaemonUpdateEngine:0x52e530> params={ EngineVersion = "1.1.0.3659"; ActivesInfo = { "com.google.talkplugin" = { LastRollCallPingDate = 2013-10-06 07:00:00 +0000; }; "com.google.Keystone" = { LastRollCallPingDate = 2013-10-06 07:00:00 +0000; LastActivePingDate = 2013-10-06 07:00:00 +0000; LastActiveDate = 2013-12-28 03:49:42 +0000; }; "com.google.picasa" = { LastActiveDate = 2012-08-29 10:15:42 +0000; }; }; UserInitiated = 0; IsSystem = 1; OmahaOSVersion = "10.8.5_i486"; Identity = KeystoneDaemon; AllowedSubdomains = ( ".omaha.sandbox.google.com", ".tools.google.com", ".www.google.com", ".corp.google.com" ); } > 12/27/13 10:49:42.130 PM GoogleSoftwareUpdateDaemon[53663]: -[KSUpdateCheckAction performAction] KSUpdateCheckAction running KSServerUpdateRequest: <KSOmahaServerUpdateRequest:0x1a31a90 server=<KSOmahaServer:0x534340> url="htt[PeeEs]://tools.google.com/service/update2" runningFetchers=0 tickets=1 activeTickets=1 rollCallTickets=1 body= <?xml version="1.0" encoding="UTF-8" standalone="yes"?> <o:gupdate xmlns:o="htt[Pee]://www.google.com/update2/request" protocol="2.0" version="KeystoneDaemon-1.1.0.3659" ismachine="1"> <o:os platform="mac" version="MacOSX" sp="10.8.5_i486"></o:os> <o:app appid="com.google.Keystone" version="1.1.0.3659" lang="en-us" installage="502" brand="GGLG"> <o:ping r="82" a="82"></o:ping> <o:updatecheck></o:updatecheck> </o:app> </o:gupdate> > 12/27/13 10:49:42.291 PM GoogleSoftwareUpdateDaemon[53663]: -[KSOutOfProcessFetcher(PrivateMethods) helperDidTerminate:] The Internet connection appears to be offline. [NSURLErrorDomain:-1009] 12/27/13 10:49:42.291 PM GoogleSoftwareUpdateDaemon[53663]: -[KSServerUpdateRequest(PrivateMethods) fetcher:failedWithError:] KSServerUpdateRequest fetch failed. (productIDs: com.google.Keystone) [com.google.UpdateEngine.CoreErrorDomain:702 - 'htt[PeeEs]://tools.google.com/service/update2'] (The Internet connection appears to be offline. [NSURLErrorDomain:-1009]) 12/27/13 10:49:42.292 PM GoogleSoftwareUpdateDaemon[53663]: -[KSUpdateCheckAction(PrivateMethods) finishAction] KSUpdateCheckAction found updates: {( )} 12/27/13 10:49:42.295 PM GoogleSoftwareUpdateDaemon[53663]: -[KSPrefetchAction performAction] KSPrefetchAction no updates to prefetch. 12/27/13 10:49:42.295 PM GoogleSoftwareUpdateDaemon[53663]: -[KSMultiUpdateAction performAction] KSSilentUpdateAction had no updates to apply. 12/27/13 10:49:42.296 PM GoogleSoftwareUpdateDaemon[53663]: -[KSMultiUpdateAction performAction] KSPromptAction had no updates to apply. 12/27/13 10:49:42.299 PM GoogleSoftwareUpdateDaemon[53663]: -[KSUpdateEngine(PrivateMethods) updateFinish] KSUpdateEngine update processing complete. 12/27/13 10:49:42.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: connect to the server /Volumes/Media Archive-1 12/27/13 10:49:42.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: connect on /Volumes/Media Archive-1 failed 65. 12/27/13 10:49:42.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: sleep for 8 seconds and then try again 12/27/13 10:49:43.152 PM GoogleSoftwareUpdateDaemon[53663]: -[KSUpdateEngine updateAllProducts] KSUpdateEngine updating all installed products. 12/27/13 10:49:43.153 PM GoogleSoftwareUpdateDaemon[53663]: -[KSCheckAction performAction] KSCheckAction checking 2 ticket(s). 12/27/13 10:49:43.158 PM GoogleSoftwareUpdateDaemon[53663]: -[KSUpdateCheckAction performAction] KSUpdateCheckAction starting update check for ticket(s): {( <KSTicket:0x18367a0 productID=com.google.Keystone version=1.1.0.3659 xc=<KSPathExistenceChecker:0x1837e10 path=/Library/Google/GoogleSoftwareUpdate/GoogleSoftwareUpdate.bundle/> serverType=Omaha url=htt[PeeEs]://tools.google.com/service/update2 creationDate=2012-08-12 14:47:10 >, <KSTicket:0x1834750 productID=com.google.talkplugin version=4.7.0.15362 xc=<KSPathExistenceChecker:0x1833890 path=/Library/Application Support/Google/GoogleTalkPlugin.app> serverType=Omaha url=htt[PeeEs]://tools.google.com/service/update2 creationDate=2012-08-12 14:47:10 > )} Using server: <KSOmahaServer:0x52e930 engine=<KSDaemonUpdateEngine:0x52e530> params={ EngineVersion = "1.1.0.3659"; ActivesInfo = { "com.google.talkplugin" = { LastRollCallPingDate = 2013-10-06 07:00:00 +0000; }; "com.google.Keystone" = { LastRollCallPingDate = 2013-10-06 07:00:00 +0000; LastActivePingDate = 2013-10-06 07:00:00 +0000; LastActiveDate = 2013-12-28 03:49:42 +0000; }; "com.google.picasa" = { LastActiveDate = 2012-08-29 10:15:42 +0000; }; }; UserInitiated = 0; IsSystem = 1; OmahaOSVersion = "10.8.5_i486"; Identity = KeystoneDaemon; AllowedSubdomains = ( ".omaha.sandbox.google.com", ".tools.google.com", ".www.google.com", ".corp.google.com" ); } > 12/27/13 10:49:43.159 PM GoogleSoftwareUpdateDaemon[53663]: -[KSUpdateCheckAction performAction] KSUpdateCheckAction running KSServerUpdateRequest: <KSOmahaServerUpdateRequest:0x53a210 server=<KSOmahaServer:0x52e930> url="htt[PeeEs]://tools.google.com/service/update2" runningFetchers=0 tickets=2 activeTickets=1 rollCallTickets=2 body= <?xml version="1.0" encoding="UTF-8" standalone="yes"?> <o:gupdate xmlns:o="htt[Pee]://www.google.com/update2/request" protocol="2.0" version="KeystoneDaemon-1.1.0.3659" ismachine="1"> <o:os platform="mac" version="MacOSX" sp="10.8.5_i486"></o:os> <o:app appid="com.google.Keystone" version="1.1.0.3659" lang="en-us" installage="502" brand="GGLG"> <o:ping r="82" a="82"></o:ping> <o:updatecheck></o:updatecheck> </o:app> <o:app appid="com.google.talkplugin" version="4.7.0.15362" lang="en-us" installage="502" brand="GGLG"> <o:ping r="82"></o:ping> <o:updatecheck></o:updatecheck> </o:app> </o:gupdate> > 12/27/13 10:49:43.243 PM GoogleSoftwareUpdateDaemon[53663]: -[KSOutOfProcessFetcher(PrivateMethods) helperDidTerminate:] The Internet connection appears to be offline. [NSURLErrorDomain:-1009] 12/27/13 10:49:43.243 PM GoogleSoftwareUpdateDaemon[53663]: -[KSServerUpdateRequest(PrivateMethods) fetcher:failedWithError:] KSServerUpdateRequest fetch failed. (productIDs: com.google.Keystone, ... (2)) [com.google.UpdateEngine.CoreErrorDomain:702 - 'htt[PeeEs]://tools.google.com/service/update2'] (The Internet connection appears to be offline. [NSURLErrorDomain:-1009]) 12/27/13 10:49:43.244 PM GoogleSoftwareUpdateDaemon[53663]: -[KSUpdateCheckAction(PrivateMethods) finishAction] KSUpdateCheckAction found updates: {( )} 12/27/13 10:49:43.247 PM GoogleSoftwareUpdateDaemon[53663]: -[KSPrefetchAction performAction] KSPrefetchAction no updates to prefetch. 12/27/13 10:49:43.248 PM GoogleSoftwareUpdateDaemon[53663]: -[KSMultiUpdateAction performAction] KSSilentUpdateAction had no updates to apply. 12/27/13 10:49:43.248 PM GoogleSoftwareUpdateDaemon[53663]: -[KSMultiUpdateAction performAction] KSPromptAction had no updates to apply. 12/27/13 10:49:43.250 PM GoogleSoftwareUpdateDaemon[53663]: -[KSUpdateEngine(PrivateMethods) updateFinish] KSUpdateEngine update processing complete. 12/27/13 10:49:45.570 PM GoogleSoftwareUpdateDaemon[53663]: -[KeystoneDaemon logServiceState] GoogleSoftwareUpdate daemon (1.1.0.3659) vending: com.google.Keystone.Daemon.UpdateEngine: 1 connection(s) com.google.Keystone.Daemon.Administration: 0 connection(s) 12/27/13 10:49:50.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: connect to the server /Volumes/Media Archive-1 12/27/13 10:49:50.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: connect on /Volumes/Media Archive-1 failed 65. 12/27/13 10:49:50.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: sleep for 10 seconds and then try again 12/27/13 10:49:53.828 PM KernelEventAgent[57]: tid 00000000 unmounting 1 filesystems 12/27/13 10:49:53.000 PM kernel[0]: AFP_VFS afpfs_unmount: /Volumes/Media Archive-1, flags 524288, pid 57 12/27/13 10:49:54.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: get the reconnect token 12/27/13 10:49:54.000 PM kernel[0]: AFP_VFS afpfs_DoReconnect: GetReconnectToken failed 32 /Volumes/Media Archive-1 12/27/13 10:49:54.000 PM kernel[0]: AFP_VFS afpfs_unmount : afpfs_DoReconnect sent signal for unmount to proceed 12/27/13 10:50:12.104 PM GoogleSoftwareUpdateDaemon[53663]: -[KeystoneDaemon main] GoogleSoftwareUpdateDaemon inactive, shutdown. 12/27/13 10:50:29.396 PM Dock[93157]: no information back from LS about running process

    Read the article

  • LACP : Cisco ASA 5515 & Switch ProCurve 2920

    - by user979276
    I've two ASAs 5515 connected in failover Active/Stand by (on Gi0/5) My two ASAs are connected to two Switch ProCurve 2920 to have HA if something happens. So I plug something like that (don't pay attention to the arrows) : So one the ASA, I created a Port-Channel like that : interface GigabitEthernet0/0 nameif outside security-level 0 ip address 192.168.1.3 255.255.255.0 standby 192.168.1.4 ! interface GigabitEthernet0/1 speed 1000 duplex full channel-group 1 mode passive no nameif no security-level no ip address ! interface GigabitEthernet0/2 speed 1000 duplex full channel-group 1 mode passive no nameif no security-level no ip address ! interface Port-channel1.1 vlan 1 nameif inside security-level 100 ip address 192.168.8.1 255.255.255.0 standby 192.168.8.2 ! interface Port-channel1.10 vlan 10 nameif guest security-level 50 ip address 172.16.100.2 255.255.255.224 standby 172.16.100.3 ! interface Port-channel1.16 vlan 16 nameif dmz security-level 50 ip address 192.168.16.1 255.255.255.0 standby 192.168.16.2 On the switch, I created a trunk LACP capable with the port 1 and 2 on each switch, force the speed to 1000 and put the port un full duplex mode. BUT this is not working... I tried many things and I can't make it work. In this configuration, I can't ping anything between my ASA and my Switch (or any object connected). Here what I get on my ASA : Channel group 1 LACP port Admin Oper Port Port Port Flags State Priority Key Key Number State ----------------------------------------------------------------------------- Gi0/2 SP not-bndl 32768 0x1 0x1 0x3 0xc Gi0/1 FP not-bndl 32768 0x1 0x1 0x2 0x6 And on the Switchs : PORT LACP TRUNK PORT LACP LACP NUMB ENABLED GROUP STATUS PARTNER STATUS ----- ------- ----- ------ ------- ------ 1 Active trk1 Broken Yes Failure 2 Active trk1 Broken Yes Failure If I change the Cisco interface to LACP mode On, I can ping the switch from the ASA but nothing other objects conneted on the switch. If I look at the statut of LACP on the switch I see this : PORT LACP TRUNK PORT LACP LACP NUMB ENABLED GROUP STATUS PARTNER STATUS ----- ------- ----- ------ ------- ------ 1 Active trk1 Up No Success 2 Active trk1 Up No Success I don't have any clue on what's going on so If someone have any idea and help me on this, it would be great ! Feel free to ask me anything if you need any more information ! Thanks a lot !

    Read the article

  • Windows startup Powershell script not closing after Start-Process

    - by Matthew Phipps
    I've got a Powershell V2.0 startup script for my work computer (XP Professional 64-bit), as follows: start "C:\Program Files (x86)\Microsoft Office\Office12\OUTLOOK.EXE" -ArgumentList "/recycle" sleep -S 2 start "C:\Program Files (x86)\Mozilla Firefox\firefox.exe" -ArgumentList "https://mail.google.com" sleep -S 2 start "C:\Program Files (x86)\Mozilla Firefox\firefox.exe" -ArgumentList "-new-window https://www.google.com/calendar" sleep -S 2 start "C:\Program Files (x86)\Skype\Phone\Skype.exe" The sleeps are to ensure that the windows appear on the taskbar in the correct order. I run this from a shortcut on my Quick Launch with the following Target: C:\WINDOWS\system32\WindowsPowerShell\v1.0\powershell.exe C:\scripts\initialize.ps1 (Yes, this is 2.0: powershell -Version 2.0 works, as does -Version 1.0, but not -Version 3.0) Problem is, the command window stays open until the Firefox windows are closed, which is not what I want. Looking at Process Explorer when I run the script, here's what happens: powershell.exe appears under explorer.exe and the Powershell window appears (with a black background, oddly. But it's not cmd.exe, since when I was debugging the script error messages would appear in red). outlook.exe appears under powershell.exe and the Outlook window appears. firefox.exe appears under powershell.exe and a Firefox window appears. A second firefox.exe appears under powershell.exe and another Firefox window appears. The second Firefox process then exits, as expected, since Firefox only uses one process. skype.exe appears under powershell.exe and the Skype window appears. The powershell.exe process inexplicably sticks around, as does the Powershell window. If I close both Firefox windows, the powershell.exe process exits and the Powershell window closes, and the outlook.exe and skype.exe processes appear under explorer.exe as expected. I suspect this has something to do with Firefox's standard input, output and error: I wouldn't expect Outlook or Skype to ever output anything to the console, but Firefox has command-line options that allow it to do so. I've looked over my about:config's user set values and didn't find anything suspicious. Finally, if I have a firefox.exe instance already running (started from the desktop shortcut) the problem doesn't occur (the powershell.exe process exits as it ought to). So what's going on here? I'm going to try adding -WindowStyle hidden to the shortcut next (gotta close this Firefox to test it), but I want to get to the bottom of this, if only to improve my understanding of how Windows consoles work.

    Read the article

  • Adaptec 5805 not recognized after reboot

    - by Rakedko ShotGuns
    After rebooting the system, the controller is not recognized. It only works if the computer is shut down and turned off. I have recently updated the firmware to "Adaptec RAID 5805 Firmware Build 18948". How do I fix the problem? Configuration summary --------------------------- 1. Server name.....................raid_test Adaptec Storage Manager agent...7.31.00 (18856) Adaptec Storage Manager console.7.31.00 (18856) Number of controllers...........1 Operating system................Windows Configuration information for controller 1 ------------------------------------------------------- Type............................Controller Model...........................Adaptec 5805 Controller number...............1 Physical slot...................2 Installed memory size...........512 MB Serial number...................8C4510C6C9E Boot ROM........................5.2-0 (18948) Firmware........................5.2-0 (18948) Device driver...................5.2-0 (16119) Controller status...............Optimal Battery status..................Charging Battery temperature.............Normal Battery charge amount (%).......37 Estimated charge remaining......0 days, 16 hours, 12 minutes Background consistency check....Disabled Copy back.......................Disabled Controller temperature..........Normal (40C / 104F) Default logical drive task priority High Performance mode................Dynamic Number of logical devices.......1 Number of hot-spare drives......0 Number of ready drives..........0 Number of drive(s) assigned to MaxCache cache0 Maximum drives allowed for MaxCache cache8 MaxCache Read Cache Pool Size...0 GB NCQ status......................Enabled Stay awake status...............Disabled Internal drive spinup limit.....0 External drive spinup limit.....0 Phy 0...........................No device attached Phy 1...........................No device attached Phy 2...........................No device attached Phy 3...........................1.50 Gb/s Phy 4...........................No device attached Phy 5...........................No device attached Phy 6...........................No device attached Phy 7...........................No device attached Statistics version..............2.0 SSD Cache size..................0 Pages on fetch list.............0 Fetch list candidates...........0 Candidate replacements..........0 69319...........................31293 Logical device..................0 Logical device name............. RAID level......................Simple volume Data space......................148,916 GB Date created....................09/19/2012 Interface type..................Serial ATA State...........................Optimal Read-cache mode.................Enabled Preferred MaxCache read cache settingEnabled Actual MaxCache read cache setting Disabled Write-cache mode................Enabled (write-back) Write-cache setting.............Enabled (write-back) Partitioned.....................Yes Protected by hot spare..........No Bootable........................Yes Bad stripes.....................No Power Status....................Disabled Power State.....................Active Reduce RPM timer................Never Power off timer.................Never Verify timer....................Never Segment 0.......................Present: controller 1, connector 0, device 0, S/N 9RX3KZMT Overall host IOs................99075 Overall MB......................4411203 DRAM cache hits.................71929 SSD cache hits..................0 Uncached IOs....................29239 Overall disk failures...........0 DRAM cache full hits............71929 DRAM cache fetch / flush wait...0 DRAM cache hybrid reads.........3476 DRAM cache flushes..............-- Read hits.......................0 Write hits......................0 Valid Pages.....................0 Updates on writes...............0 Invalidations by large writes...0 Invalidations by R/W balance....0 Invalidations by replacement....0 Invalidations by other..........0 Page Fetches....................0 0...............................0 73..............................10822 8...............................3 46138...........................4916 27184...........................15226 20875...........................323 16982...........................1771 1563............................5317 1948............................2969 Serial attached SCSI ----------------------- Type............................Disk drive Vendor..........................Unknown Model...........................ST3160815AS Serial Number...................9RX3KZMT Firmware level..................3.AAD Reported channel................0 Reported SCSI device ID.........0 Interface type..................Serial ATA Size............................149,05 GB Negotiated transfer speed.......1.50 Gb/s State...........................Optimal S.M.A.R.T. error................No Write-cache mode................Write back Hardware errors.................0 Medium errors...................0 Parity errors...................0 Link failures...................0 Aborted commands................0 S.M.A.R.T. warnings.............0 Solid-state disk (non-spinning).false MaxCache cache capable..........false MaxCache cache assigned.........false NCQ status......................Enabled Phy 0...........................1.50 Gb/s Power State.....................Full rpm Supported power states..........Full rpm, Powered off 0x01............................113 0x03............................98 0x04............................99 0x05............................100 0x07............................83 0x09............................75 0x0A............................100 0x0C............................99 0xBB............................100 0xBD............................100 0xBE............................61 0xC2............................39 0xC3............................69 0xC5............................100 0xC6............................100 0xC7............................200 0xC8............................100 0xCA............................100 Aborted commands................0 Link failures...................0 Medium errors...................0 Parity errors...................0 Hardware errors.................0 SMART errors....................0 End of the configuration information for controller 1

    Read the article

  • Daemon process exiting when shell closes

    - by Pace
    I have a script which starts a daemon process and then sleeps for 20 seconds. If I run the script on SLES11 SP1 or RHEL6 then after the script exits the process is still running. If I run the script on SLES11 SP3 or RHEL6.3 then after the script exits the process is no longer running. The process continues to run for the entire 20 second sleep and is killed when the process exits. The script is run via expect so the script's entire shell exits with the process. Obviously if this wasn't a daemon it was starting I wouldn't be surprised. Also, I suspect the problem isn't the OS version as much as it is the difference in the way we've setup the newer servers (no idea what those differences are though, the older servers were set up years ago). During the 20 seconds the process runs if I do a ps I get the following: root 4699 1 0 15:14 pts/2 00:00:00 sudo -u openmq /opt/PacketPortal/openmq/default/bin/imqbrokerd -bgnd -autorestart -silent -port 7676 -Dimq.service.activelist=admin,ssljms -D openmq 4701 4699 0 15:14 pts/2 00:00:00 /bin/sh /opt/PacketPortal/openmq/default/bin/imqbrokerd -bgnd -autorestart -silent -port 7676 -Dimq.service.activelist=admin,ssljms -Dimq.ssl The fact that the parent process of 4699 is 1 seems to suggest to me that the process has been correctly daemonized. However, after the expect script exits both 4699 and 4701 are killed. What could be causing this? UPDATE I've printed the same output on the servers that work. During the 20 second sleep I get: openmq 18652 1 0 15:44 pts/1 00:00:00 /bin/sh /opt/PacketPortal/openmq/default/bin/imqbrokerd -bgnd -autorestart -silent -port 7676 -Dimq.service.activelist=admin,ssljms -Dimq.ssljms.tls.port=7680 openmq 18686 18652 8 15:44 pts/1 00:00:02 /usr/java/latest/bin/java -cp /opt/PacketPortal/openmq/default/bin/../lib/imqbroker.jar:/opt/PacketPortal/openmq/default/bin/../lib/imqutil.jar:/opt/PacketPortal/ope After the 20 second sleep I get: openmq 18652 1 0 15:44 ? 00:00:00 /bin/sh /opt/PacketPortal/openmq/default/bin/imqbrokerd -bgnd -autorestart -silent -port 7676 -Dimq.service.activelist=admin,ssljms -Dimq.ssljms.tls.port=7680 openmq 18686 18652 5 15:44 ? 00:00:02 /usr/java/latest/bin/java -cp /opt/PacketPortal/openmq/default/bin/../lib/imqbroker.jar:/opt/PacketPortal/openmq/default/bin/../lib/imqutil.jar:/opt/PacketPortal/ope After the script exits it disconnects the controlling terminal. I wonder why it doesn't do that on the newer servers. UPDATE Here is the section of the script that actually launches OpenMQ. The -bgnd flag is what is supposed to daemonize it. sudo -u openmq $IMQ_HOME/bin/$EXECUTABLE -bgnd $BROKER_OPTIONS $ARGS > /dev/null 2>&1 &

    Read the article

  • HP Probook 6550b has issues with an external monitor

    - by chama
    I recently got a new HP Probook 6550b laptop for work. However, very often, when left alone (not put to sleep), the built in display will go dark. Not only that, but whenever I plug in an external monitor, the display will blank out as well. Sometimes after this happens, putting the laptop to sleep and then waking it up solves the problem. But only sometimes and only for a short time. The next time I plug in my monitor, it happens again. I know this isn't only my problem - 6 other people got the same laptop as I have at the same time, and we're all having such issues. Any suggestions as to the root of this problem and a way to fix it? It's driving me crazy!

    Read the article

  • What would cause intermittent DomainKey-Status: failures?

    - by wherestheph
    Every week, we send something like a small newsletter. Sometimes, the header in the newsletter says DomainKey-Status: bad (test mode) Sometimes it says DomainKey-Status: good (test mode) All the other headers in the email are the same (besides expected time and message id differences). None of the email server configuration has changed. What would cause this problem?

    Read the article

  • ls, rm, cd commands not working in SUSE LINUX

    - by Jak
    Hi All, Iam newbi to SUSE, I installed java in my SUSE linux Server edition, So i want to set the path in linux,So i created .bash_profile in in /root path using touch and added the path as "JAVA_PATH". When restart my linux the above command is not working and it show unknown command "JAVA_PATH", I can't able to boot in GUI mode, I can boot only in terminal mode, How to delete the file (.bash_profile in /root) ? And how to add java path in SUSE Note: Before all the commands are working fine Thanks in Advance, Jak...

    Read the article

  • Looking for Ubuntu 10.10 driver for GeForce GT 425M GPU.

    - by Fantomas
    It came with my Sony VAIO® VPCF133FX/H 16.4" Notebook. Ubuntu does suggest an NVIDIA driver for me, but when I install it, I cannot boot back in normally. I have to boot into a failsafe mode, then reset graphics setting to default, and reboot again. Right now I am stuck in 800 x 600 mode, but I would like to do better, and take advantage of my 1GB graphics memory :(. Please let me know if you have questions.

    Read the article

  • Windows 8 Unable to perform hibernate

    - by Jones
    Windows 8 Enterprise edition x86. Already enabled hibernate option, to have it on shutdown menu (start menu?) and set to hibernate on lid closing. However it's not hibernating for me. When I'm trying to sleep, it's sleep fine and wake up like a kid. But when I'm demanding hibernate, it disconnects internet, turn off screen and be back to lock screen in one second. Steps I've tried. Complete shutdown Clear hiberfile.sys by disabling and enabling back Resetting my power settings. Causes I suspect: Had dual boot with BackTrack with Windows 8 GUI boot manager. It was fine until I reinstall BackTrack, bootmgr resetted and I'm in Ubuntu boot menu;. Using additional hard disk through USB cable.(But it's not a problem before few days, however) How to make my system to hibernate and wakeup again.

    Read the article

  • SQL 2008 Replication

    - by sevenlamp
    I have replicated two database in SQL2008. The last two days the distribution database from publisher server changed to Suspect Mode and the replication process is down. I read a lot from Google and tried to repair, but without success. During my repairing process, the Distribution Database is has changed to Emergency mode. Can anyone please kindly suggest any solutions?

    Read the article

  • Backup of Xen servers and laptops with encryption

    - by Konrads
    Hello, I have the following backup objects: Multiple Xen Linux instances running on same box. A few laptops Windows that contain also private data that needs to be stored encrypted I have this backup media: A disk attached to the Xen box A disk available remotely for off-site backups I want to do daily-weekly-monthly backups of Xen systems and to back-up laptops in approximately same mode but in push mode (backup initiated by laptop) with encryption. Any good free solutions?

    Read the article

  • Printer offline until spooler service is restarted multiple times

    - by Zian Choy
    When I try to print from my ThinkPad to a printer shared through a Windows 7 Homegroup hosted by a desktop computer, I often have to restart the Print Spooler service several times before the job will go through. In particular, this problem occurs when the desktop is in sleep mode when the print job is started and then brought out of sleep mode after the print job has been kicked off. Both computers are running Windows 7 32-bit edition with the latest patches. I have tried the following with no improvement: SNMP registry hack (see MS KB for details) Following the instructions in a blog post entitled "Sharing Printers on Vista 64-bit" Looking at Printer offline until spooler service is restarted

    Read the article

  • Linux compatible touchscreen monitor

    - by jrtokarz
    Can anybody recommend a linux compatible touchscreen monitor, the criteria are: 19inch or greater 1920x1080 or better only single touch required be able to operate in portait mode We currently have some IIyama Prolite MTS2250MS monitors but these do not natively support portait mode and we have had little success getting the touch functionality working in Linux (although they do report themselves as HID devices when plugged in). So an alternative to suggesting a monitor would be pointers to information on how we could get the IIyama monitor working in Linux.

    Read the article

< Previous Page | 104 105 106 107 108 109 110 111 112 113 114 115  | Next Page >