Search Results

Search found 3006 results on 121 pages for 'virus scan'.

Page 108/121 | < Previous Page | 104 105 106 107 108 109 110 111 112 113 114 115  | Next Page >

• How to remove iso 9660 from USB?

  - by a_m0d

  I have somehow managed to write an iso 9660 image onto my USB drive, which makes all my computer think that the device is actually a CD. I have tried various methods of removing this partition, but nothing seems to work. I have tried fdisk, which says $ fdisk -l /dev/sdb Cannot open /dev/sdb parted crashes when I try to use it on this device. I have even tried $ dd if=/dev/zero of=/dev/sdb but it just hangs with no output (either on screen or on disk). However, when I plug the USB in, it does mount, and I can view (but not edit) the files on it. edit: now the result is $ dd if=/dev/zero of=/dev/sdb dd: opening `/dev/sdb': Read-only file system I have also tried re-formatting it on Windows, but it gets to the end of the format process and then says "Couldn't format the drive". How can I remove this partition and get my whole USB drive back to normal again? EDIT 1: Trying a simple mkfs doesn't work: $ sudo mkfs -t vfat /dev/sdb mkfs.vfat 3.0.0 (28 Sep 2008) mkfs.vfat: Will not try to make filesystem on full-disk device '/dev/sdb' (use -I if wanted) I can't do mkfs on /dev/sdb1 because there is no such partition, as shown:$ ls /dev | grep sdb sdb EDIT 2: This is the information posted by dmesg when I plug the device in:$ dmesg . . (snip) . usb 2-1: New USB device found, idVendor=058f, idProduct=6387 usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 2-1: Product: Mass Storage usb 2-1: Manufacturer: Generic usb 2-1: SerialNumber: G0905000000000010885 usb-storage: device found at 4 usb-storage: waiting for device to settle before scanning usb-storage: device scan complete scsi 6:0:0:0: Direct-Access FLASH Drive AU_USB20 8.07 PQ: 0 ANSI: 2 sd 6:0:0:0: [sdb] 4069376 512-byte hardware sectors (2084 MB) sd 6:0:0:0: [sdb] Write Protect is off sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00 sd 6:0:0:0: [sdb] Assuming drive cache: write through sd 6:0:0:0: [sdb] 4069376 512-byte hardware sectors (2084 MB) sd 6:0:0:0: [sdb] Write Protect is off sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00 sd 6:0:0:0: [sdb] Assuming drive cache: write through sdb: unknown partition table sd 6:0:0:0: [sdb] Attached SCSI removable disk sd 6:0:0:0: Attached scsi generic sg2 type 0 ISO 9660 Extensions: Microsoft Joliet Level 3 ISO 9660 Extensions: RRIP_1991A SELinux: initialized (dev sdb, type iso9660), uses genfs_contexts CE: hpet increasing min_delta_ns to 15000 nsec This shows that the device is formatted as ISO 9660 and that it is /dev/sdb. EDIT 3: This is the message that I find at the bottom of dmesg after running cfdisk and writing a new partition table to the disk:SELinux: initialized (dev sdb, type iso9660), uses genfs_contexts sd 17:0:0:0: [sdb] Device not ready: Sense Key : Not Ready [current] sd 17:0:0:0: [sdb] Device not ready: < ASC=0xff ASCQ=0xffASC=0xff < ASCQ=0xff end_request: I/O error, dev sdb, sector 0 Buffer I/O error on device sdb, logical block 0 lost page write due to I/O error on sdb

  Read the article

• Malware - Technical anlaysis

  - by nullptr

  Note: Please do not mod down or close. Im not a stupid PC user asking to fix my pc problem. I am intrigued and am having a deep technical look at whats going on. I have come across a Windows XP machine that is sending unwanted p2p traffic. I have done a 'netstat -b' command and explorer.exe is sending out the traffic. When I kill this process the traffic stops and obviously Windows Explorer dies. Here is the header of the stream from the Wireshark dump (x.x.x.x) is the machines IP. GNUTELLA CONNECT/0.6 Listen-IP: x.x.x.x:8059 Remote-IP: 76.164.224.103 User-Agent: LimeWire/5.3.6 X-Requeries: false X-Ultrapeer: True X-Degree: 32 X-Query-Routing: 0.1 X-Ultrapeer-Query-Routing: 0.1 X-Max-TTL: 3 X-Dynamic-Querying: 0.1 X-Locale-Pref: en GGEP: 0.5 Bye-Packet: 0.1 GNUTELLA/0.6 200 OK Pong-Caching: 0.1 X-Ultrapeer-Needed: false Accept-Encoding: deflate X-Requeries: false X-Locale-Pref: en X-Guess: 0.1 X-Max-TTL: 3 Vendor-Message: 0.2 X-Ultrapeer-Query-Routing: 0.1 X-Query-Routing: 0.1 Listen-IP: 76.164.224.103:15649 X-Ext-Probes: 0.1 Remote-IP: x.x.x.x GGEP: 0.5 X-Dynamic-Querying: 0.1 X-Degree: 32 User-Agent: LimeWire/4.18.7 X-Ultrapeer: True X-Try-Ultrapeers: 121.54.32.36:3279,173.19.233.80:3714,65.182.97.15:5807,115.147.231.81:9751,72.134.30.181:15810,71.59.97.180:24295,74.76.84.250:25497,96.234.62.221:32344,69.44.246.38:42254,98.199.75.23:51230 GNUTELLA/0.6 200 OK So it seems that the malware has hooked into explorer.exe and hidden its self quite well as a Norton Scan doesn't pick anything up. I have looked in Windows firewall and it shouldn't be letting this traffic through. I have had a look into the messages explorer.exe is sending in Spy++ and the only related ones I can see are socket connections etc... My question is what can I do to look into this deeper? What does malware achieve by sending p2p traffic? I know to fix the problem the easiest way is to reinstall Windows but I want to get to the bottom of it first, just out of interest. Edit: Had a look at Deoendency Walker and Process Explorer. Both great tools. Here is a image of the TCP connections for explorer.exe in Process Explorer http://img210.imageshack.us/img210/3563/61930284.gif

  Read the article

• RAID 50 24Port Fast Writes Slow Reads - Ubuntu

  - by James

  What is going on here?! I am baffled. serveradmin@FILESERVER:/Volumes/MercuryInternal/test$ sudo dd if=/dev/zero of=/Volumes/MercuryInternal/test/test.fs bs=4096k count=10000 10000+0 records in 10000+0 records out 41943040000 bytes (42 GB) copied, 57.0948 s, 735 MB/s serveradmin@FILESERVER:/Volumes/MercuryInternal/test$ sudo dd if=/Volumes/MercuryInternal/test/test.fs of=/dev/null bs=4096k count=10000 10000+0 records in 10000+0 records out 41943040000 bytes (42 GB) copied, 116.189 s, 361 MB/s OF NOTE: My RAID50 is 3 sets of 8 disks. - This might not be the best config for SPEED. OS: Ubuntu 12.04.1 x64 Hardware Raid: RocketRaid 2782 - 24 Port Controller HardDriveType: Seagate Barracuda ES.2 1TB Drivers: v1.1 Open Source Linux Drivers. So 24 x 1TB drives, partitioned using parted. Filesystem is ext4. I/O scheduler WAS noop but have changed it to deadline with no seemingly performance benefit/cost. serveradmin@FILESERVER:/Volumes/MercuryInternal/test$ sudo gdisk -l /dev/sdb GPT fdisk (gdisk) version 0.8.1 Partition table scan: MBR: protective BSD: not present APM: not present GPT: present Found valid GPT with protective MBR; using GPT. Disk /dev/sdb: 41020686336 sectors, 19.1 TiB Logical sector size: 512 bytes Disk identifier (GUID): 95045EC6-6EAF-4072-9969-AC46A32E38C8 Partition table holds up to 128 entries First usable sector is 34, last usable sector is 41020686302 Partitions will be aligned on 2048-sector boundaries Total free space is 5062589 sectors (2.4 GiB) Number Start (sector) End (sector) Size Code Name 1 2048 41015625727 19.1 TiB 0700 primary To me this should be working fine. I can't think of anything that would be causing this other then fundamental driver errors? I can't seem to get much/if any higher then the 361MB a second, is this hitting the "SATA2" link speed, which it shouldn't given it is a PCIe2.0 card. Or maybe some cacheing quirk - I do have Write Back enabled. Does anyone have any suggestions? Tests for me to perform? Or if you require more information, I am happy to provide it! This is a video fileserver for editing machines, so we have a preference for FAST reads over writes. I was just expected more from RAID 50 and 24 drives together... EDIT: (hdparm results) serveradmin@FILESERVER:/Volumes/MercuryInternal$ sudo hdparm -Tt /dev/sdb /dev/sdb: Timing cached reads: 17458 MB in 2.00 seconds = 8735.50 MB/sec Timing buffered disk reads: 884 MB in 3.00 seconds = 294.32 MB/sec EDIT2: (config details) Also, I am using a RAID block size of 256K. I was told a larger block size is better for larger (in my case large video) files. EDIT3: (Bonnie++ Results. Would love some guidance with this!)

  Read the article

• Controling virtualbox internet access?

  - by HandyGandy

  I am finally going through the process of moving my XP into a vbox (host linux). The thing is that I am migrating a virtually clean install. So aside from the occasional antivirus scan, I want to make sure that my XP is not sending malware data (keystoke.logs, spam etc. ) out silently ( and thus having picked up some virus ). To that end I want to limit XP to contacting my LAN and a few internet sites. ( mainly sites that require proprietary windows only software to access, AV sites and Windows update ). I want XP to only access preapproved addresses. If it is trying to contact a nonapproved address, I want it somehow logged and access restricted until I allow access. I also don't want to have to decide whether to allow access to a site at my leisure. To keeps things clear let me give an example: I start my vbox/XP ( which I call MYXP) running on my linux box ( called MYLINUX connecting to the net through a linksys wrt54g ) and connects via samba to my LAN ( since my LAN seems to be possessed of every evil thing, it's address is 192.168.666. ). At the moment my configuration is set so that I allow MYXP to access 192.168.666 and www.MYANTIVIRUS_UPDATES.com and www.MS_UPDATES.com. Then on the VM I start a program which tries to make a connection to www.playmygame.com . www.playmygame.com is on my preapproved list so the connection goes through. Later I check attempted accesses and discover that it also tried to connect to www.mygame_high_scores.com I figure this is OK so I add www.mygame_high_scores.com to my approved list. Later, I again check address and discover that my VM/XP tried to access www.mygame_steals_your_identity.com. I do some checking and discover the address is registered to someone in Kiev, Nigeria. Since this doesn't sound kosher to me, I replace the MYXP VM with one that was backed up before I installed mygame. I remove www.playmygame.com and www.mygame_high_scores.com from my access list for MYXP. It should acomplish this with little overheard. When I am not running the VM ideally it should not have any overhead. Suggestions?

  Read the article

• After compiling PHP, I get mod_fcgid: error reading data from FastCGI server

  - by user34295

  I'm trying to add multiple PHP version in Plesk 12. Switching my domain to the new version PHP 5.4.29 result in this error: (104)Connection reset by peer: mod_fcgid: error reading data from FastCGI server Here is phpinfo() of the complied PHP version, obtained running php54-cgi index.php from the terminal. The same script placed under document root doesn't work in FastCGI. How can I debug/try to figure out what's the error? Currently running CentOS 6.5 x64, Plesk v12.0.18_build1200140529.2, PHP 5.5.13. I've downloaded PHP 5.4.29: cd /usr/local/src curl -O http://it1.php.net/distributions/php-5.4.29.tar.gz cd php-5.4.29 And configured with: ./configure \ --prefix=/usr/local/php54 \ --with-bz2 \ --with-config-file-path=/usr/local/php54/etc \ --with-config-file-scan-dir=/usr/local/php54/etc/php.d \ --with-curl \ --with-gd \ --with-gettext \ --with-iconv \ --with-layout=PHP \ --with-libxml-dir=/usr/local/php54 \ --with-mhash \ --with-mysql=mysqlnd \ --with-mysqli=mysqlnd \ --with-openssl \ --with-pdo-mysql=mysqlnd \ --with-readline \ --with-xsl \ --with-zlib \ --enable-calendar \ --enable-cgi \ --enable-exif \ --enable-ftp \ --enable-intl \ --enable-mbstring \ --enable-pcntl \ --enable-shmop \ --enable-sockets \ --enable-sockets \ --enable-sysvmsg \ --enable-sysvsem \ --enable-sysvshm \ --enable-wddx \ --enable-zip Then: make && make install Installing PHP CLI binary: /usr/local/php54/bin/ Installing PHP CLI man page: /usr/local/php54/php/man/man1/ Installing PHP CGI binary: /usr/local/php54/bin/ Installing PHP CGI man page: /usr/local/php54/php/man/man1/ Installing build environment: /usr/local/php54/lib/php/build/ Installing header files: /usr/local/php54/include/php/ Installing helper programs: /usr/local/php54/bin/ program: phpize program: php-config Installing man pages: /usr/local/php54/php/man/man1/ page: phpize.1 page: php-config.1 Installing PEAR environment: /usr/local/php54/lib/php/ [PEAR] Archive_Tar - installed: 1.3.11 [PEAR] Console_Getopt - installed: 1.3.1 warning: pear/PEAR requires package "pear/Structures_Graph" (recommended version 1.0.4) warning: pear/PEAR requires package "pear/XML_Util" (recommended version 1.2.1) [PEAR] PEAR - installed: 1.9.4 Wrote PEAR system config file at: /usr/local/php54/etc/pear.conf You may want to add: /usr/local/php54/lib/php to your php.ini include_path [PEAR] Structures_Graph- installed: 1.0.4 [PEAR] XML_Util - installed: 1.2.1 /usr/local/src/php-5.4.29/build/shtool install -c ext/phar/phar.phar /usr/local/php54/bin ln -s -f /usr/local/php54/bin/phar.phar /usr/local/php54/bin/phar Installing PDO headers: /usr/local/php54/include/php/ext/pdo/ Copied php.ini-production to /usr/local/php54/etc/php.ini and added a new handler in Plesk: /usr/local/psa/bin/php_handler --add -displayname 5.4.29 -path /usr/local/php54/bin/php-cgi -phpini /usr/local/php54/etc/php.ini -type fastcgi -id php54 Symbolic linking: ln -s /usr/local/php54/bin/php /usr/local/bin/php54 ln -s /usr/local/php54/bin/php-cgi /usr/local/bin/php54-cgi New installed version: php54-cgi -m [PHP Modules] bz2 calendar cgi-fcgi Core ctype curl date dom ereg exif fileinfo filter ftp gd gettext hash iconv intl json libxml mbstring mhash mysql mysqli mysqlnd openssl pcntl pcre PDO pdo_mysql pdo_sqlite Phar posix readline Reflection session shmop SimpleXML sockets SPL sqlite3 standard sysvmsg sysvsem sysvshm tokenizer wddx xml xmlreader xmlwriter xsl zip zlib [Zend Modules]

  Read the article

• Partition table corrupted (USB flash drive)

  - by 13ren

  It's an 8 GB Patriot thumb drive, which I've used extensively with lots of data. Today, it is detected, but all data is gone: (EDIT at least some data is still there, but the partition table is gone) EDIT @Sathya (thanks) here's the relevant output from sudo fdisk -l: Disk /dev/sdc: 8019 MB, 8019509248 bytes 247 heads, 62 sectors/track, 1022 cylinders Units = cylinders of 15314 * 512 = 7840768 bytes Disk /dev/sdc doesn't contain a valid partition table It looks like it is /dev/sdc, with that 8 GB... and no partition table. I tried to mount /dev/sdc (and then dmesg | tail): /media> sudo mount /dev/sdc mytmp mount: wrong fs type, bad option, bad superblock on /dev/sdc, missing codepage or other error In some cases useful info is found in syslog - try dmesg | tail or so /media> dmesg | tail [ 24.300000] sdc: unknown partition table [ 24.320000] sd 2:0:0:0: Attached scsi removable disk sdc [ 24.370000] usb-storage: device scan complete [ 26.870000] EXT2-fs error (device sdc): ext2_check_descriptors: Block bitmap for group 1 not in group (block 0)! [ 26.870000] EXT2-fs: group descriptors corrupted! [ 50.420000] unhashed dentry being revalidated: .DCOPserver_eeepc-brendanma__0 [ 50.430000] unhashed dentry being revalidated: .DCOPserver_eeepc-brendanma__0 [ 50.430000] unhashed dentry being revalidated: .DCOPserver_eeepc-brendanma__0 [ 5565.470000] EXT2-fs error (device sdc): ext2_check_descriptors: Block bitmap for group 1 not in group (block 0)! [ 5565.470000] EXT2-fs: group descriptors corrupted! EDIT @Col: results from testdisk Disk /dev/sdc - 8013 MB / 7642 MiB - CHS 1022 247 62 Current partition structure: Partition Start End Size in sectors Partition sector doesn't have the endmark 0xAA55 After I hit [proceed], it says: Structure: Ok. Keys A: add partition, L: load backup, Enter: to continue The "Structure: Ok." seems reassuring... will "A: add partition" make my old data accessible (if it's still there), or will it make a new, fresh partition? Another option is "[ MBR Code ] Write TestDisk MBR code to first sector" - would it be better to do this? EDIT I found that at least some of my data is still on the flash drive, by using the below, and searching for English text in less (like " the "): cat /dev/sde | tr -cd '\11\12\40\1540-\176' | less (The drive changed from "/dev/sdb" to "/dev/sde" because I connected some extra drives today). I've learnt that "/dev/sde1" would be the first partition; and "/dev/sde" is the whole drive. Because unix treats these devices just like files, you can use all the ordinary unix file commands on them, like cat, and then process them like any other stream of data. The tr above removes non-printable characters ("\40" is space, which I wanted to preserve). In less, you can use "/" to search, similar to Vim. How can I get my data back (assuming it's still there)? If only the partition table is corrupted, is there a standard "partition recovery tool"? Is there a way to "repartition" without deleting everything?

  Read the article

• Trouble using gitweb with nginx

  - by Rayne

  I have a git repository in a directory inside of /home/raynes/pubgit/. I'm trying to use gitweb to provide a web interface to it. I use nginx as my web server for everything else, so I don't really want to have to use another just for this. I'm mostly following this guide: http://michalbugno.pl/en/blog/gitweb-nginx, which is the only guide I can find via google and is really recent. fcgiwrap apparently isn't in Lucid Lynx's repositories, so I installed it manually. I spawn instances via spawn-fcgi: spawn-fcgi -f /usr/local/sbin/fcgiwrap -a 127.0.0.1 -p 9001 That's all good. My /etc/gitweb.conf is as follows: # path to git projects (<project>.git) #$projectroot = "/home/raynes/pubgit"; $my_uri = "http://mc.raynes.me"; $home_link = "http://mc.raynes.me/"; # directory to use for temp files $git_temp = "/tmp"; # target of the home link on top of all pages #$home_link = $my_uri || "/"; # html text to include at home page $home_text = "indextext.html"; # file with project list; by default, simply scan the projectroot dir. $projects_list = $projectroot; # stylesheet to use $stylesheet = "/gitweb/gitweb.css"; # logo to use $logo = "/gitweb/git-logo.png"; # the 'favicon' $favicon = "/gitweb/git-favicon.png"; And my nginx server configuration is this: server { listen 80; server_name mc.raynes.me; location / { root /usr/share/gitweb; if (!-f $request_filename) { fastcgi_pass 127.0.0.1:9001; } fastcgi_index index.cgi; fastcgi_param SCRIPT_FILENAME /scripts$fastcgi_script_name; include fastcgi_params; } } The only difference here is that I've set fastcgi_pass to 127.0.0.1:9001. When I go to http://mc.raynes.me I'm greeted with a page that simply says "403" and nothing else. I have not the slightest clue what I did wrong. Any ideas?

  Read the article

• Windows DHCP Server - get notification when a non-AD joined device gets an IP address

  - by TheCleaner

  SCENARIO To simplify this down to it's easiest example: I have a Windows 2008 R2 standard DC with the DHCP server role. It hands out IPs via various IPv4 scopes, no problem there. WHAT I'D LIKE I would like a way to create a notification/eventlog entry/similar whenever a device gets a DHCP address lease and that device IS NOT a domain joined computer in Active Directory. It doesn't matter to me whether it is custom Powershell, etc. Bottom line = I'd like a way to know when non-domain devices are on the network without using 802.1X at the moment. I know this won't account for static IP devices. I do have monitoring software that will scan the network and find devices, but it isn't quite this granular in detail. RESEARCH DONE/OPTIONS CONSIDERED I don't see any such possibilities with the built in logging. Yes, I'm aware of 802.1X and have the ability to implement it long-term at this location but we are some time away from a project like that, and while that would solve network authentication issues, this is still helpful to me outside of 802.1X goals. I've looked around for some script bits, etc. that might prove useful but the things I'm finding lead me to believe that my google-fu is failing me at the moment. I believe the below logic is sound (assuming there isn't some existing solution): Device receives DHCP address Event log entry is recorded (event ID 10 in the DHCP audit log should work (since a new lease is what I'd be most interested in, not renewals): http://technet.microsoft.com/en-us/library/dd759178.aspx) At this point a script of some kind would probably have to take over for the remaining "STEPS" below. Somehow query this DHCP log for these event ID 10's (I would love push, but I'm guessing pull is the only recourse here) Parse the query for the name of the device being assigned the new lease Query AD for the device's name IF not found in AD, send a notification email If anyone has any ideas on how to properly do this, I'd really appreciate it. I'm not looking for a "gimme the codez" but would love to know if there are alternatives to the above list or if I'm not thinking clear and another method exists for gathering this information. If you have code snippets/PS commands you'd like to share to help accomplish this, all the better.

  Read the article

• Hell: NTFS "Restore previous versions"...

  - by ttsiodras

  The hell I have experienced these last 24h: Windows 7 installation hosed after bluetooth driver install. Attempting to recover using restore points via "Repair" on the bootable Win7 installation CD. Attempting to go back one day in the restore points. No joy. Attempting to go back two days in the restore points. No joy. Attempting to go back one week in the restore points. Stil no joy. Windows won't boot. Apparently something is REALLY hosed. And then it hits me - PANIC - the restore points somehow reverted DATA files to their older versions! Word, Powerpoint, SPSS, etc document versions are all one week old now. Using the "freshest" restore point. Failed to restore yesterday's restore point!!! I am stuck at old versions of the data!!! Booting KNOPPIX, mounting NTFS partition as read-only under KNOPPIX. Checking. Nope, the data files are still the one week old versions. Booting Win7 CD, Recovery console - Cmd prompt - navigating - yep, data files are still one week old. Removing the drive, mounting it under other Win7 installation. Still old data. Running NTFS undelete on the drive (read-only scan), searching for file created yesterday. Not found. Despair. At this point, idea: I will install a brand new Windows installation, keeping the old one in Windows.old (default behaviour of Windows installs). I boot the new install, I go to my C:\Data\ folder, I choose "Restore previous versions", click on yesterday's date, and click open... YES! It works! I can see the latest versions of my files (e.g. from yesterday). Thank God. And then, I try to view the files under the "yesterday snapshot-version" of c:\Users\MyAccount\Desktop ... And I get "Permission Denied" as soon as I try to open "Users\MyAccount". I make sure I am an administrator. No joy. Apparently, the new Windows installation does not have access to read the "NTFS snapshots" or "Volume Shadow Snapshots" of my old Windows account! Cross-installation permissions? I need to somehow tell the new Windows install that I am the same "old" user... So that I will be able to access the "Users\MyAccount" folder of the snapshot of my old user account. Help?

  Read the article

• Are random packets normal?

  - by TheLQ

  About a month ago on one of my servers I started receiving random packets from IPs all over the world. So I did the smart thing and stopped putting off installing an IDS. This IDS is a ClearOS Gateway which comes with Snort and SnortSam. I enabled it, checked There is a total of 4 ports open, two of which forward to the server I'm talking about. These ports are 3724 and 8085, so they aren't going to be easily detected in a port scan. However checking some logs of this server I found that the attack is resuming. I found this ... Accepting connection from '75.166.155.122' [Auth] got unknown packet from '75.166.155.122' Accepting connection from '98.164.154.93' [Auth] got unknown packet from '98.164.154.93' Ping MySQL to keep connection alive Accepting connection from '70.241.195.129' [Auth] got unknown packet from '70.241.195.129' Accepting connection from '67.182.229.169' [Auth] got unknown packet from '67.182.229.169' Accepting connection from '69.137.140.38' [Auth] got unknown packet from '69.137.140.38' Accepting connection from '76.31.72.55' [Auth] got unknown packet from '76.31.72.55' Accepting connection from '97.88.139.39' [Auth] got unknown packet from '97.88.139.39' Accepting connection from '173.35.62.112' [Auth] got unknown packet from '173.35.62.112' Accepting connection from '187.15.10.73' [Auth] got unknown packet from '187.15.10.73' Accepting connection from '66.66.94.124' [Auth] got unknown packet from '66.66.94.124' Accepting connection from '75.159.219.124' [Auth] got unknown packet from '75.159.219.124' Accepting connection from '99.102.100.82' [Auth] got unknown packet from '99.102.100.82' Accepting connection from '24.128.240.45' [Auth] got unknown packet from '24.128.240.45' Accepting connection from '99.231.7.39' [Auth] got unknown packet from '99.231.7.39' Accepting connection from '206.255.79.56' [Auth] got unknown packet from '206.255.79.56' Accepting connection from '68.97.106.235' [Auth] got unknown packet from '68.97.106.235' Accepting connection from '69.134.67.251' [Auth] got unknown packet from '69.134.67.251' Accepting connection from '63.228.138.186' [Auth] got unknown packet from '63.228.138.186' Accepting connection from '184.39.146.193' [Auth] got unknown packet from '184.39.146.193' Accepting connection from '69.171.161.102' [Auth] got unknown packet from '69.171.161.102' Accepting connection from '76.0.47.228' [Auth] got unknown packet from '76.0.47.228' Ping MySQL to keep connection alive Accepting connection from '126.112.201.14' [Auth] got unknown packet from '126.112.201.14' Ping MySQL to keep connection alive Now that scares me. Why isn't Snort detecting this? How were they able to find this specific port? More importantly, what normally would these packets contain? Is this something I should be worried about? How can I stop this?

  Read the article

• Impact of the L3 cache on performance - worth a dual-processor system?

  - by Dan Nissenbaum

  I will be purchasing a new high-end system, and I would like to have a better sense of whether a dual-processor Xeon system (I am looking at the new, high-end Xeon E5-2687W) might, realistically, provide a noticeable performance improvement due to the doubling of the L3 cache (20 MB per CPU). (This is in addition to the occasional added advantage due to the doubling of cores and RAM.) My usage scenario is, roughly, that I have many background applications running at any time - 3 or 4 data compression/backup applications, a low-impact web server, one or two virtual machines at any given time (usually fairly idle), and perhaps 20 utility programs that utilize a noticeable (but small) portion of the CPU cores. In total, when I am not actively using the computer, about 25% of the total CPU power is utilized in my current i7-970 6-core (12 thread) system. When I am doing routine work, the CPU utilization often exceeds 50%, and occasionally hits 75%-80%. The Xeon E5-2687W is not only a second-generation i7 (so should improve performance for that reason), but also has 8 cores (16 threads), rather than 6 cores. For this reason, I expect to run into the 75% CPU range even less frequently. Nonetheless, the ability to double the cores and the RAM is a consideration. However, in the end, I believe this decision comes down to whether the doubling of the L3 cache will provide a noticeable improvement. There are many benchmarks, and a lot of discussion, regarding CPU power. However, I find very little discussion of L3 cache utilization, and how increases in the L3 cache (such as doubling it with dual processors) affect performance. For example: If there are only two processes running, but each benefits from a large L3 cache (such as might be the case for background processes that frequently scan the file system), perhaps the overall system performance might noticeably improve with dual CPU's - even if only a single core is active on each CPU - due to each process having double the effective L3 cache. I am hoping that someone has a sense of the benefits of increasing (or doubling) the L3 cache size. Note: the CPU I am considering (the Xeon E5-2687W) has 20 MB L3 cache, so a system with dual CPU's would have 40 MB L3 cache.

  Read the article

• Firefox can't establish a connection to the server at www.google.com

  - by Tom

  My home page in Firefox [v4.0] and Internet Explorer [v9.0.8112.16421, Update Versions RTM (KB982861)] is currently set to Google but when I depress the quick start icon to start up either browser, I am getting the following immediate results: Unable to connect (In Firefox) Firefox can't establish a connection to the server at www.google.com. The site could be temporarily unavailable or too busy. Try again in a few moments. If you are unable to load any pages, check your computer's network connection. If your computer or network is protected by a firewall or proxy, make sure that Firefox is permitted to access the Web. Internet Explorer cannot display the webpage What you can try: Diagnose Connection Problems More information This problem can be caused by a variety of issues, including: Internet connectivity has been lost. The website is temporarily unavailable. The Domain Name Server (DNS) is not reachable. The Domain Name Server (DNS) does not have a listing for the website's domain. There might be a typing error in the address. If this is an HTTPS (secure) address, click Tools, click Internet Options, click Advanced, and check to be sure the SSL and TLS protocols are enabled under the security section. For offline users You can still view subscribed feeds and some recently viewed webpages. To view subscribed feeds: Click the Favorites button , click Feeds, and then click the feed you want to view. To view recently visited webpages (might not work on all pages): Press Alt, click File, and then click Work Offline. Click the Favorites button, click History, and then click the page you want to view. Thankfully, I am able to use one browser that I have installed on my computer (Mathon v3.0.20.5000) to search online for technical assistance in this matter. I have seen several WinSock error issues mentioned; but, they are pointing to Windows XP and I am using Windows 7 Pro and remain uncertain whether anything identified as a fix for one OS will work in another. Things I've tried: HiJackThis Complete scan with Avira AntiVirus Premium. What am I overlooking? What should I do to address this problem?

  Read the article

• Getting an boot error when starting computer

  - by Rob Avery IV

  I was in the middle of watching a movie on Netflix, then suddenly everything started crashing. First, explorer.exe closed down, then Google chrome. I had multiple things running in the background (Steam, Raptr, etc.). Individuality, each of those apps closed down also. When they did, a small dialog box popped up for each of them, one at a time, saying that it was missing a file, it couldn't run anymore, or something similar to that. It also had some jumbled up "code" with numbers and letters that I couldn't read. Ever since then, everytime I turn my computer on, it will run for a few seconds and give this error "Reboot and select proper boot device or insert boot media in selected boot device and press a key_". No matter how many times I try to reboot it, it always gives me the same error. A day later after this happened I was able to start the computer, but before it booted, it told me that I didn't shut down the computer properly and asked how I wanted to run the OS (Run Windows in Safety Mode, Run Windows Normally, etc.). Once I logged, everything went SUPER slow and everything crashed almost instantly. The only thing I opened was Microsoft Security Essentials and only got in about two clicks before it was "Not Responding". Then, after that the whole computer froze and I had to restart it. Now, it's back to saying what it originally said, "Reboot and select proper boot device or insert boot media in selected boot device and press a key_". I built this PC back in February 2012. Here are the specs: OS: Windows 7 Ultimate CPU: AMD 8-core GPU: Nvidia GTX Force 560 Ti RAM: 16GB Hard Drive: Hitachi Deskstar 750GB I'm usually very good taking care of my PC. I don't download anything that's not from a trusted site or source. I don't open up any spam email or such or go to any harmful websites like porn or stream movies. I am very clean with the things I do with my PC and don't do many DIFFERENT things with it. I use it pretty often especially for video games and doing homework in Eclipse. Also, good to note that I don't have any Norton or antisoftware installed. I have Microsoft Security Essentials installed but never did a scan. Thanks!

  Read the article

• LdapErr: DSID-0C0903AA, data 52e: authenticating against AD '08 with pam_ldap

  - by Stefan M

  I have full admin access to the AD '08 server I'm trying to authenticate towards. The error code means invalid credentials, but I wish this was as simple as me typing in the wrong password. First of all, I have a working Apache mod_ldap configuration against the same domain. AuthType basic AuthName "MYDOMAIN" AuthBasicProvider ldap AuthLDAPUrl "ldap://10.220.100.10/OU=Companies,MYCOMPANY,DC=southit,DC=inet?sAMAccountName?sub?(objectClass=user)" AuthLDAPBindDN svc_webaccess_auth AuthLDAPBindPassword mySvcWebAccessPassword Require ldap-group CN=Service_WebAccess,OU=Groups,OU=MYCOMPANY,DC=southit,DC=inet I'm showing this because it works without the use of any Kerberos, as so many other guides out there recommend for system authentication to AD. Now I want to translate this into pam_ldap.conf for use with OpenSSH. The /etc/pam.d/common-auth part is simple. auth sufficient pam_ldap.so debug This line is processed before any other. I believe the real issue is configuring pam_ldap.conf. host 10.220.100.10 base OU=Companies,MYCOMPANY,DC=southit,DC=inet ldap_version 3 binddn svc_webaccess_auth bindpw mySvcWebAccessPassword scope sub timelimit 30 pam_filter objectclass=User nss_map_attribute uid sAMAccountName pam_login_attribute sAMAccountName pam_password ad Now I've been monitoring ldap traffic on the AD host using wireshark. I've captured a successful session from Apache's mod_ldap and compared it to a failed session from pam_ldap. The first bindrequest is a success using the svc_webaccess_auth account, the searchrequest is a success and returns a result of 1. The last bindrequest using my user is a failure and returns the above error code. Everything looks identical except for this one line in the filter for the searchrequest, here showing mod_ldap. Filter: (&(objectClass=user)(sAMAccountName=ivasta)) The second one is pam_ldap. Filter: (&(&(objectclass=User)(objectclass=User))(sAMAccountName=ivasta)) My user is named ivasta. However, the searchrequest does not return failure, it does return 1 result. I've also tried this with ldapsearch on the cli. It's the bindrequest that follows the searchrequest that fails with the above error code 52e. Here is the failure message of the final bindrequest. resultcode: invalidcredentials (49) 80090308: LdapErr: DSID-0C0903AA, comment: AcceptSecurityContext error, data 52e, v1772 This should mean invalid password but I've tried with other users and with very simple passwords. Does anyone recognize this from their own struggles with pam_ldap and AD? Edit: Worth noting is that I've also tried pam_password crypt, and pam_filter sAMAccountName=User because this worked when using ldapsearch. ldapsearch -LLL -h 10.220.100.10 -x -b "ou=Users,ou=mycompany,dc=southit,dc=inet" -v -s sub -D svc_webaccess_auth -W '(sAMAccountName=ivasta)' This works using the svc_webaccess_auth account password. This account has scan access to that OU for use with apache's mod_ldap.

  Read the article

• Wirelss card not being detected in backtrack 5

  - by Jesse Nelson

  I just installed backtrack 5 and I am unable to detect my wireless card. iwconfig doesn't list my interface. I can see that the hardware is present in lspci -vnn (see below) but I can't get the interface detected. I have tried to reinstall the compat-wireless package but I get errors during the build (see below) I have done a ton of researching and I keep hitting a brick wall, mostly because the wiki for backtrack is down and I can't find any good resources. Does anyone know how to fix the issue? Also, does anyone no how I can scan the hardware to determine what NIC is assigning my interface? If I can figure out the interface name I think I can set it up manually by putting up the link and using wireless-tools to manually configure the connection, this is what I had to do in arch on my mac. As stated the wiki for backtrack is down and I can't find any help on the issue. I tried to do the full kernel upgrade suggested in my software update but after the update was complete and I logged back in I had a new log in manager and the only thing I was able to log into was window managers. However, after this update my wireless was working fine. Please help I am new to Linux and the wiki is down, I have nowhere else to turn. Forgot to mention I am using the KDE version, not Gnome. Thanks in advance for any help or support. Attempt at make: root@bt:/usr/src/compat-wireless-3.3-rc1-2# make /usr/src/compat-wireless-3.3-rc1-2/config.mk:254: "WARNING: CONFIG_CFG80211_WEXT will be deactivated or not working because kernel was compiled with CONFIG_WIRELESS_EXT=n. Tools using wext interface like iwconfig will not work. To activate it build your kernel e.g. with CONFIG_LIBIPW=m." make -C /lib/modules/2.6.38/build M=/usr/src/compat-wireless-3.3-rc1-2 modules make: *** /lib/modules/2.6.38/build: No such file or directory. Stop. make: *** [modules] Error 2 lspci output: root@bt:/usr/src/compat-wireless-3.3-rc1-2# lspci -vnn -i net lspci: I/O error at net, line 0 root@bt:/usr/src/compat-wireless-3.3-rc1-2# lspci -vnn 02:00.0 Network controller [0280]: Atheros Communications Inc. Device [168c:0032] (rev ff) (prog-if ff) !!! Unknown header type 7f ( This is the problem but I can't find the solution) Kernel modules: ath9k iwconfig output: root@bt:/usr/src/compat-wireless-3.3-rc1-2# iwconfig lo no wireless extensions. eth0 no wireless extensions.

  Read the article

• Mercurial local repository backup

  - by Ricket

  I'm a big fan of backing things up. I keep my important school essays and such in a folder of my Dropbox. I make sure that all of my photos are duplicated to an external drive. I have a home server where I keep important files mirrored across two drives inside the server (like a software RAID 1). So for my code, I have always used Subversion to back it up. I keep the trunk folder with a stable copy of my application, but then I create a branch named with my username, and inside there is my working copy. I make very few changes between commits to that branch, with the understanding that the code in there is my backup. Now I'm looking into Mercurial, and I must admit I haven't truly used it yet so I may have this all wrong. But it seems to me that you have a server-side repository, and then you clone it to a working directory in the form of a local repository. Then as you work on something, you make commits to that local repository, and when things are in a state to be shared with others, you hg push to the parent repository on the server. Between pushes of stable, tested, bug-free code, where is the backup? After doing some thinking, I've come to the conclusion that it is not meant for backup purposes and it assumes you've handled that on your own. I guess I need to keep my Mercurial local repositories in my dropbox or some other backed-up location, since my in-progress code is not pushed to the server. Is this pretty much it, or have I missed something? If you use Mercurial, how do you backup your local repositories? If you had turned on your computer this morning and your hard drive went up in flames (or, more likely, the read head went bad, or the OS corrupted itself, ...), what would be lost? If you spent the past week developing a module, writing test cases for it, documenting and commenting it, and then a virus wipes your local repository away, isn't that the only copy? So then on the flip side, do you create a remote repository for every local repository and push to it all the time? How do you find a balance? How do you ensure your code is backed up? Where is the line between using Mercurial as backup, and using a local filesystem backup utility to keep your local repositories safe?

  Read the article

• Problems with MGCP proxy creation

  - by Popof

  Hi, I'm trying to bypass my ISP router with my FreeBSD server (I've an optical connection so I've a RJ45 used to connect the box to WAN) Internet and TV are working fine (Using igmpproxy to forward TV stream) but I've a problem with phone. ISP's box is connected to the server which gives it a LAN address. The problem is that when the box builds MGCP packets (and especially SDP ones) it uses its LAN address. So I've think of writing an UDP proxy to handle MGCP and SDP packets in order to replace LAN address with server WAN address and then forward packet to WAN. Before starting coding I've captured stream packets using my server as a bridge between WAN connection and the ISP's box. And, in order to see if my solution is viable, I've tried to send those packets to the box using nemesis. I tried to send a packet (found in capture) containing an endpoint audit: AUEP 1447 aaln/[email protected] MGCP 1.0 F: A In the wireshark capture the box replied: 200 1447 OK A: a:PCMU;PCMA;G726-16;G726-24;G726-32;G726-40;G.723.1-5.3;G.723.1-6.3;G729;TELEPHONE-EVENT, fmtp:"TELEPHONE-EVENT 0-15,144,149,159", p:10-30, b:4-40, e:on, t:00, s:on, v:L;M;G;D, m:sendonly;recvonly;sendrecv;inactive;confrnce;replcate;netwtest;netwloop, dq-gi But when I use nemesis, I got an ICMP error: Port unreachable (Type 3, Code 3). To build this packet, WAN source address of the capture is replaced with my server LAN address, using the mgcp-callagent port (2727) and the packet is sent to the LAN address of the box at mgcp-gateway port (2427). The command I use is nemesis udp -S 192.168.2.1 -D 192.168.2.2 -x 2727 -y 2427 -P packet_to_send. I also tried an UDP scan to the box on callagent and gateway port: PORT STATE SERVICE 2727/udp open|filtered unknown 2427/udp closed unknown I found those results a little bit strange because it should be the 2427 port opened, as it was in capture. Internet Protocol, Src: <ISP MGCP Server>, Dst: <My WAN Address> User Datagram Protocol, Src Port: mgcp-callagent (2727), Dst Port: mgcp-gateway (2427) Does someone has any idea about how having my box responding to my requests ? Thanks in advance and sorry for my english.

  Read the article

• Recovering data from failed Raid configuration with 4 drives and two raid sets (Asus P6T / Intel ICH10r)

  - by user56365

  I've added the complete detailed version for my question below for those who can help, but want to quickly summarize my question first. I setup two Raid arrays using (4) WD Raptors, a striped set for the OS and 1+0 set for crucial data. After booting once out of the 50 times a cable fell out, the drive wasn't recognized in the array anymore. After trying to fix it, another drive did the same. I now have two drives remaining, luckily with the parity information. I know the striped set is gone, but I need the data on the other set. Can anyone recommend anything to recover the data, or fix the two drives that doesn't allow the raid controller to recognize the drives, even though they are listed on the utility screen as still apart of the configuration but that they are not found? More Details I recently upgraded to a ASUS P6T motherboard with an Intel ICH10R raid controller and changed my previous 4 drive raid array from strictly a Raid 1+0 set to a Raid 0 for the OS/Page/Scratch drive and a Raid 1+0 set for crucial data. I never had problems after upgrading with my configuration, even when a drive died and was replaced. I managed to rebuild the array fine. Unfortunately this time around, a cable came unattached and I booted my system up until the raid status screen with the degraded error. This shouldn't have been a problem, but after I attached the drive it was no longer recognized as a member in the array. Both drives actually show up as a non-member disk. I've spent a very, very long time online trying to find information or support and haven't had much luck. After spending time trying to scan the drive for errors, damaged partition info, etc.. another drive in the set decided it didn't want to be recognized as a part of the array. At this point, I have two out of the four drives still functioning, but the Raid 1+0 array went from degraded to failed and I must find a way to retrieve that data. I think the two drives still in the array have the parity information because they show up as OS (110GB),BACKUP(80GB) and OS:1(110GB),BACKUP(80GB) under windows data management. The other two are simply 74gb Raw unallocated Is it possible recover the data using those two drive only, and which tool would I use? Could it be a simple partition table or any other error that is repairable with hard drive utilities out there? I know the Raid 0 set is done for, but I would assume because the correct drives failed in a 1+0 config to save the data I can retrieve it some how.

  Read the article

• Frequent and weird wifi disconnections

  - by Sidou

  How would you explain, troubleshoot (and solve) the following problem? Wifi ADSL modem router D-link 2640R installed in living room at about 1.8m height. Working fine, synchronising and getting/serving stable internet connection. First situation: -Laptop 01 in other end of the house, let's say in room01 southern to the living room, distant by about 15m. Getting stable signal of good to very good quality. No disconnection. -Laptop 02 in room02 opposite to room01 (5m West) which makes it almost at the same distance and direction from the router located 15m North. Getting stable signal of good to very good quality. No disconnection. Second situation: -Laptop 01 moved to room03 Northern to the living room (actually just 3m behind the wall where the router lies). Getting stable signal of excellent quality. No disconnection. -Laptop 02 still in room02 but now experiences frequent disconnections (actually almost impossible to get the Internet even though the signal level is still very good. Either no Internet with the wifi icon appearing connected to access point or no connection established at all which happens every 2 minutes and that means virtually no Internet at all as I can just get a timeframe of 1 minute or so to load any website or even get to the router's web based control panel. If Laptop 01 is completely shut down or its wifi adapters shut down or even still working but its wifi MAC address forbidden, then Laptop 02 has no problem at all. If Laptop 02 is moved to a nearer location to the router, in the living room for instance, then no connection problem occurs even if Laptop 01 is also connected. And also if we move back Laptop 01 to its original location (room 01), then no problem as well. I'm completely lost and don't know how to address this issue. I tried to change the Wifi channel and even tried the auto channel scan but that didn't solve it. I know that the problem is probably coming from Laptop 01 being in its new location or some sort of interference as the problem occurs only under the described condition but I have no idea how to solve it! I also scanned the neighborhood for wifi jam using InSSIDer, there are few other access points but they don't seem to affect the situation. Any ideas about the steps to follow or tools to use ?

  Read the article

• ZFS Recover from Faulted Pool State

  - by nickv2002

  I have a six disk ZFS raidz1 pool and had a recent failure requiring a disk replacement. No problem normally, but this time my server hardware died before I could do the replacement (but after and unrelated to the drive failure as far as I can tell). I was able to get another machine from a friend to rebuild the system, but in the process of moving my drives over I had to swap their cables around a bunch until I got the right configuration where the remaining 5 good disks were seen as online. This process seems to have generated some checksum errors for the pool/raidz. I have the 5 remaining drives set up now and a good drive installed and ready to take the place of the drive that died. However, since my pool state is FAULTED I'm unable to do the replacement. root@zfs:~# zpool replace tank 1298243857915644462 /dev/sdb cannot open 'tank': pool is unavailable Is there any way to recover from this error? I would think that having 5 of the 6 drives online would be enough to rebuild the right data, but that doesn't seem to be enough now. Here's the status log of my pool: root@zfs:~# zpool status tank pool: tank state: FAULTED status: One or more devices could not be used because the label is missing or invalid. There are insufficient replicas for the pool to continue functioning. action: Destroy and re-create the pool from a backup source. see: http://zfsonlinux.org/msg/ZFS-8000-5E scan: none requested config: NAME STATE READ WRITE CKSUM tank FAULTED 0 0 1 corrupted data raidz1-0 ONLINE 0 0 8 sdd ONLINE 0 0 0 sdf ONLINE 0 0 0 sdh ONLINE 0 0 0 1298243857915644462 UNAVAIL 0 0 0 was /dev/sdb1 sde ONLINE 0 0 0 sdg ONLINE 0 0 0 Update (10/31): I tried to export and re-import the array a few times over the past week and wasn't successful. First I tried: zpool import -f -R /tank -N -o readonly=on -F tank That produced this error immediately: cannot import 'tank': I/O error Destroy and re-create the pool from a backup source. I added the '-X' option to the above command to try to make it check the transaction log. I let that run for about 48 hours before giving up because it had completely locked up my machine (I was unable to log in locally or via the network). Now I'm trying a simple zpool import tank command and that seems to run for a while with no output. I'll leave it running overnight to see if it outputs anything.

  Read the article

• Why does this service refuse to start on Windows server 2003?

  - by PenguinCoder

  We have a Windows 2003 server with Cebos MQ1 (ver. 7 and ver. GRI) products installed that have been operational for years. After installing Microsoft 2010 C++ Redistributable package needed for other development, the MQ1 GRI service now fails to start. Event logs showed that two additional updates (.NET4 and the 2010 C++ Redistributable SP2) where installed by the redistributable as well. As soon as we discovered the MQ1 service was not starting properly, we removed these three installed packages. However the service still does not start; the dialog that pops up states 'The service started then stopped. '. Event logs when we attempt to start the service show nothing; IE: No errors, crashes, failures, or other information related to this service. Executing the MQ1Serv.exe directly specifies an issue of 'Missing command line operation, must specify install, uninstall and company abbreviation.' sc query MQ1Service(GRI) shows a clean exit for the Win32ExitCode of 0x0. Attempting to reinstall the client or server software gives an error of 'The procedure entry point ReInitializeCriticalSection could not be located in the dynamic link library KERNEL32.dll.' at the 'Registering Libraries' stage. At this point, further research has stated that the required function is in URL.dll and to verify the library is not corrupted. Running an sfc /scannow on the server has replaced a few DLLS; including the URL.DLL to versions from 2005. This actually broke other applications which required a reinstall (one of them being IE 7). After reinstall and updates, url.dll version is 7.0.5730.13 (2009) and Kernel32.dll is version 5.2.3790.4480 (2009). The MQ1 GRI service still will not start, specifying the same error as previous 'Service started then stopped'. Running a disassembler on Kernel32.dll and Url.dll show no functions named ReinitializeCriticalSection. Attempting the reinstall of the MQ1 client and server as well as starting the service again, fails once more. However, setting the compatibility mode on the MQ1 client install exe to 'Windows 95' actually gets the program to install. Setting the compatibility mode on the MQ1 server service does not enable it to start. I have been researching this problem for nearly a week and besides the advice to scan and replace url.dll, have come to no successful conclusions. This service was operational prior to the 2010 C++ install, without any additional parameters or settings. After removing the C++ install and all servicepacks/updates it installed silently, still does not correct the issue of the MQ1 GRI service not starting. Q: Has anyone else run into this or similar issue while attempting to get a service initialized? What have I overlooked or what else can I try in order to get this service started??

  Read the article

• windows 7 virtual wireless adapter keeps going to sleep

  - by conners

  Just a quick question that I can't see mentioned anywhere online. I have a Windows 7 box configured like these guys recommend http://www.itgeekdiary.com/windows-7-as-an-wi-fi-access-point/ simply so that I can have my Windows 7 box as a wifi access point or a wifi emitter. It's also called a Microsoft Virtual WiFi Miniport Adapter. But it powers off and shuts down automatically and stops working. Basically everything works as intended and then - well -it will stopped working when I am not at the Windows 7 PC for a long time. The problem seems to be that every time my PC goes to "power save / sleep" and in the morning the Windows 7 machine "wakes" but blooming heck the wifi has stopped and you have to power cycle the PC (which is very uncool). When I power Cycle I have to do the following as administrator C:\Windows\System32\netsh.exe wlan start hostednetwork I then tried a gazllion things involving services and power management and eventually discovered that if I run the following commands as administrator it will be ok (for a bit) but every 3rd ot 4th time I try this "trick" it simply fails. the trick that seems to work 3 out of 4 times (i.e. "most" of the time) C:\Windows\System32\netsh.exe wlan stop hostednetwork C:\Windows\System32\netsh.exe wlan start hostednetwork But why does this only work "some" of the time? What else I did by myself: on every manage adapter properties (that relates to the wifi) I right clicked [configure] [power management] /disabled/ "allow the computer to power off to save power" <- this made no difference Also (and this is a bit annoying) there is no system tray app/GUI for the Microsoft Virtual WiFi Miniport Adapter output signal ... none... so (lame as it sounds) the ONLY way I can check if it's on is to physically go to another device and SCAN.. lame so my question can probably be solved by any of the following: a) can I stop Windows 7 sleeping this wifi when the machine sleeps b) can I force Windows to force wake this process on wake? if so how? c) what is the service / process REALLY called and how do I restart it if it crashes d) how can I flush the wifi properly rather power cycle the host machine e) anyone have a link to an program or app that can sit in the system tray that shows windows 7 wifi hotspot emission status (on/off/etc etc) Since I am a programmer I can easily write a vbs script / windows exe to fix this (and I will share this solution) and the gui problem if I can work out the actual service that is running that netsh stops/starts

  Read the article

• bluetooth connection using pybluez

  - by srj0408

  I am working on bluetooth not exactly on bluetooth stack-development but to use bluetooth in one of my project. I had done all that before using some of the py-bluez commands like hciconfig, hcitool scan , then simple-agents and using serial module inside python. But that was quite random. We were able to connect only one specific device based on its bluetooth address and there was no facility of reconnection once the devices are disconnected. Now i want to try out this stuff in a sequential manner like this (i am doing that all on a RPI and for at present on ubuntu 12.04.) i) Store some names in a file along with some other information with respect to that device. ii) Run a script to find out the device in locality with those names and if any one if found, report that. For this step, i had taken a reference from BTBook , made available from MIT. Below is the script for the same, but that script only search for the single name. from bluetooth import * target_name = "XT1033" target_address = None nearby_devices = discover_devices() for address in nearby_devices: if target_name == lookup_name( address ): target_address = address break if target_address is not None: print "found target bluetooth device with address ", target_address connect_socket(target_address); else: print "could not find target bluetooth device nearby" iii) Connect the device using client sock. But i dont have any device on which i can write a simple python script. My client can be any device that will be publishing data. Now i came through a script in the same book, that actually connect to a client requesting permission to connect to server. from bluetooth import * port = 1 server_sock=BluetoothSocket( RFCOMM ) server_sock.bind(("",port)) server_sock.listen(1) client_sock, client_info = server_sock.accept() print "Accepted connection from ", client_info data = client_sock.recv(1024) print "received [%s]" % data client_sock.close() server_sock.close() here client_sock, client_info = server_sock.accept() provide the client address and port requested to be connected. Can i pass address obtained from the earlier script to this, so that it connect server to the client? iv) Then if client get disconnected, re-connect(a simple polling can be used.) All this stuff can be done using bash and py-bluez functions but i want to do that in a sequential manner.I am not a master in python but i can do some small stuff. Can any one guide me for the same or can direct me to more usefull resource through which i can continue my coding part after finding the "X", "Y" named devices.

  Read the article

• Android app crashes on emulator - logCat shows no errors

  - by David Miler

  I have just added the SherlockActionBar library to my android project. After some small changes (FragmentActivity - SherlockFragmentActivity, getActionBar() - getSupportActionBar(), imports) it all compiled nicely. After I run the app, however, the debugger stops, as though it had encountered an exception. However, there are no errors shown in the LogCat output. I just can't wrap my head around what's going on. Here is the logCat output after I terminate the app. 10-02 14:11:19.227: I/SystemUpdateService(174): UpdateTask at time 1349187079227 10-02 14:11:19.237: I/ActivityThread(328): Pub com.android.email.attachmentprovider: com.android.email.provider.AttachmentProvider 10-02 14:11:19.687: I/dalvikvm(81): Jit: resizing JitTable from 512 to 1024 10-02 14:11:19.809: D/MediaScannerService(150): start scanning volume internal: [/system/media] 10-02 14:11:20.047: V/AlarmClock(239): AlarmInitReceiver finished 10-02 14:11:20.087: I/ActivityManager(81): Start proc com.android.quicksearchbox for broadcast com.android.quicksearchbox/.SearchWidgetProvider: pid=346 uid=10012 gids={3003} 10-02 14:11:20.127: D/ExchangeService(320): !!! EAS ExchangeService, onStartCommand, startingUp = false, running = false 10-02 14:11:20.427: I/ActivityThread(346): Pub com.android.quicksearchbox.google: com.android.quicksearchbox.google.GoogleSuggestionProvider 10-02 14:11:20.497: I/ActivityThread(346): Pub com.android.quicksearchbox.shortcuts: com.android.quicksearchbox.ShortcutsProvider 10-02 14:11:20.657: I/ActivityManager(81): Start proc com.android.music for broadcast com.android.music/.MediaAppWidgetProvider: pid=358 uid=10028 gids={3003, 1015} 10-02 14:11:20.927: D/ExchangeService(320): !!! EAS ExchangeService, onCreate 10-02 14:11:20.967: D/dalvikvm(260): GC_CONCURRENT freed 213K, 6% free 6409K/6791K, paused 5ms+101ms 10-02 14:11:21.077: D/ExchangeService(320): !!! EAS ExchangeService, onStartCommand, startingUp = true, running = false 10-02 14:11:21.567: D/GTalkService(174): [ReonnectMgr] ### report Inet condition: status=false, networkType=0 10-02 14:11:21.587: D/ConnectivityService(81): reportNetworkCondition(0, 0) 10-02 14:11:21.597: D/ConnectivityService(81): Inet connectivity change, net=0, condition=0,mActiveDefaultNetwork=0 10-02 14:11:21.597: D/ConnectivityService(81): starting a change hold 10-02 14:11:21.697: D/GTalkService(174): [RawStanzaProvidersMgr] ##### searchProvidersFromIntent 10-02 14:11:21.697: D/GTalkService(174): [RawStanzaProvidersMgr] no intent receivers found 10-02 14:11:21.847: I/SystemUpdateService(174): cancelUpdate (empty URL) 10-02 14:11:21.847: E/TelephonyManager(174): Hidden constructor called more than once per process! 10-02 14:11:21.867: D/dalvikvm(174): GC_CONCURRENT freed 337K, 7% free 6561K/7047K, paused 5ms+4ms 10-02 14:11:21.917: D/GTalkService(174): [ReonnectMgr] ### report Inet condition: status=false, networkType=0 10-02 14:11:21.917: D/ConnectivityService(81): reportNetworkCondition(0, 0) 10-02 14:11:21.917: D/ConnectivityService(81): Inet connectivity change, net=0, condition=0,mActiveDefaultNetwork=0 10-02 14:11:21.917: D/ConnectivityService(81): currently in hold - not setting new end evt 10-02 14:11:21.990: E/TelephonyManager(174): Original: com.google.android.location, new: com.google.android.gsf 10-02 14:11:22.027: I/SystemUpdateService(174): removeAllDownloads (cancelUpdate) 10-02 14:11:22.127: D/dalvikvm(328): GC_CONCURRENT freed 205K, 6% free 6506K/6855K, paused 660ms+3ms 10-02 14:11:22.197: D/Eas Debug(320): Logging: 10-02 14:11:22.319: D/dalvikvm(81): GREF has increased to 401 10-02 14:11:22.947: D/ExchangeService(320): !!! EAS ExchangeService, onStartCommand, startingUp = true, running = false 10-02 14:11:23.130: D/Eas Debug(320): Logging: 10-02 14:11:23.307: I//system/bin/fsck_msdos(29): Attempting to allocate 2044 KB for FAT 10-02 14:11:23.560: I/ActivityManager(81): Starting: Intent { flg=0x10000000 cmp=com.google.android.gsf/.update.SystemUpdateInstallDialog } from pid 174 10-02 14:11:23.587: I/ActivityManager(81): Starting: Intent { flg=0x10000000 cmp=com.google.android.gsf/.update.SystemUpdateDownloadDialog } from pid 174 10-02 14:11:24.087: W/ActivityManager(81): Activity pause timeout for ActivityRecord{407c7320 com.android.launcher/com.android.launcher2.Launcher} 10-02 14:11:24.237: E/TelephonyManager(174): Hidden constructor called more than once per process! 10-02 14:11:24.237: E/TelephonyManager(174): Original: com.google.android.location, new: com.google.android.gsf 10-02 14:11:24.507: D/dalvikvm(174): GC_EXPLICIT freed 231K, 7% free 6596K/7047K, paused 4ms+6ms 10-02 14:11:24.607: D/ConnectivityService(81): Inet hold end, net=0, condition =0, published condition =0 10-02 14:11:24.607: D/ConnectivityService(81): no change in condition - aborting 10-02 14:11:24.707: D/dalvikvm(174): GC_EXPLICIT freed 17K, 7% free 6579K/7047K, paused 4ms+4ms 10-02 14:11:24.947: I//system/bin/fsck_msdos(29): ** Phase 2 - Check Cluster Chains 10-02 14:11:25.117: I//system/bin/fsck_msdos(29): ** Phase 3 - Checking Directories 10-02 14:11:25.128: I//system/bin/fsck_msdos(29): ** Phase 4 - Checking for Lost Files 10-02 14:11:25.167: I//system/bin/fsck_msdos(29): 12 files, 1044448 free (522224 clusters) 10-02 14:11:25.227: I/Vold(29): Filesystem check completed OK 10-02 14:11:25.227: I/Vold(29): Device /dev/block/vold/179:0, target /mnt/sdcard mounted @ /mnt/secure/staging 10-02 14:11:25.237: D/Vold(29): Volume sdcard state changing 3 (Checking) -> 4 (Mounted) 10-02 14:11:25.257: I/PackageManager(81): Updating external media status from unmounted to mounted 10-02 14:11:25.457: D/dalvikvm(303): GC_EXPLICIT freed 35K, 6% free 6242K/6595K, paused 3ms+312ms 10-02 14:11:25.987: D/ExchangeService(320): !!! EAS ExchangeService, onStartCommand, startingUp = true, running = false 10-02 14:11:26.157: D/MediaScanner(150): prescan time: 2905ms 10-02 14:11:26.167: D/MediaScanner(150): scan time: 148ms 10-02 14:11:26.167: D/MediaScanner(150): postscan time: 2ms 10-02 14:11:26.167: D/MediaScanner(150): total time: 3055ms 10-02 14:11:26.197: D/MediaScannerService(150): done scanning volume internal 10-02 14:11:26.237: D/MediaScannerService(150): start scanning volume external: [/mnt/sdcard] 10-02 14:11:26.497: D/dalvikvm(143): GC_EXPLICIT freed 234K, 8% free 7735K/8327K, paused 3ms+5ms 10-02 14:11:27.180: D/dalvikvm(143): GC_CONCURRENT freed 150K, 4% free 8004K/8327K, paused 7ms+3ms 10-02 14:11:27.397: D/dalvikvm(143): GC_FOR_ALLOC freed 96K, 6% free 8310K/8775K, paused 76ms 10-02 14:11:27.580: D/dalvikvm(143): GC_FOR_ALLOC freed 515K, 11% free 8135K/9095K, paused 79ms 10-02 14:11:27.829: D/dalvikvm(143): GC_CONCURRENT freed 3K, 5% free 8694K/9095K, paused 7ms+6ms 10-02 14:11:28.137: V/TLINE(143): new: android.text.TextLine@4065b280 10-02 14:11:28.527: D/dalvikvm(143): GC_CONCURRENT freed 729K, 10% free 8764K/9671K, paused 5ms+13ms 10-02 14:11:28.677: D/dalvikvm(143): GC_FOR_ALLOC freed 152K, 11% free 8683K/9671K, paused 99ms 10-02 14:11:28.717: I/dalvikvm-heap(143): Grow heap (frag case) to 11.434MB for 2975968-byte allocation 10-02 14:11:28.807: D/dalvikvm(143): GC_FOR_ALLOC freed 0K, 9% free 11589K/12615K, paused 84ms 10-02 14:11:29.159: D/dalvikvm(143): GC_CONCURRENT freed 197K, 7% free 12195K/12999K, paused 8ms+6ms 10-02 14:11:29.647: D/dalvikvm(143): GC_EXPLICIT freed 351K, 6% free 12790K/13511K, paused 8ms+17ms 10-02 14:11:29.717: I/SurfaceFlinger(32): Boot is finished (70768 ms) 10-02 14:11:29.877: I/ARMAssembler(32): generated scanline__00000177:03010104_00000002_00000000 [ 44 ipp] (66 ins) at [0x407c7290:0x407c7398] in 990662 ns 10-02 14:11:29.907: I/ARMAssembler(32): generated scanline__00000177:03515104_00000001_00000000 [ 73 ipp] (95 ins) at [0x407c73a0:0x407c751c] in 989381 ns 10-02 14:11:30.287: D/dalvikvm(174): GC_EXPLICIT freed 25K, 8% free 6554K/7047K, paused 4ms+32ms 10-02 14:11:30.380: D/dalvikvm(143): GC_EXPLICIT freed 349K, 6% free 13124K/13895K, paused 5ms+25ms 10-02 14:11:30.957: D/dalvikvm(143): GC_FOR_ALLOC freed 1069K, 10% free 13860K/15239K, paused 81ms 10-02 14:11:32.177: D/dalvikvm(150): GC_CONCURRENT freed 183K, 6% free 6438K/6791K, paused 5ms+4ms 10-02 14:11:32.187: W/ActivityManager(81): No content provider found for: 10-02 14:11:32.607: V/MediaScanner(150): pruneDeadThumbnailFiles... android.database.sqlite.SQLiteCursor@406724a8 10-02 14:11:32.617: V/MediaScanner(150): /pruneDeadThumbnailFiles... android.database.sqlite.SQLiteCursor@406724a8 10-02 14:11:32.640: W/ActivityManager(81): No content provider found for: 10-02 14:11:32.640: D/VoldCmdListener(29): asec list 10-02 14:11:32.647: I/PackageManager(81): No secure containers on sdcard 10-02 14:11:32.667: D/MediaScanner(150): prescan time: 107ms 10-02 14:11:32.667: D/MediaScanner(150): scan time: 89ms 10-02 14:11:32.667: D/MediaScanner(150): postscan time: 61ms 10-02 14:11:32.667: D/MediaScanner(150): total time: 257ms 10-02 14:11:32.697: W/PackageManager(81): Unknown permission android.permission.ADD_SYSTEM_SERVICE in package com.android.phone 10-02 14:11:32.707: W/PackageManager(81): Unknown permission com.android.smspush.WAPPUSH_MANAGER_BIND in package com.android.phone 10-02 14:11:32.737: W/PackageManager(81): Not granting permission android.permission.SEND_DOWNLOAD_COMPLETED_INTENTS to package com.android.browser (protectionLevel=2 flags=0x9be45) 10-02 14:11:32.737: W/PackageManager(81): Not granting permission android.permission.BIND_APPWIDGET to package com.android.widgetpreview (protectionLevel=3 flags=0x28be44) 10-02 14:11:32.767: W/PackageManager(81): Unknown permission android.permission.READ_OWNER_DATA in package com.android.exchange 10-02 14:11:32.778: W/PackageManager(81): Unknown permission android.permission.READ_OWNER_DATA in package com.android.email 10-02 14:11:32.788: W/PackageManager(81): Unknown permission com.android.providers.im.permission.READ_ONLY in package com.google.android.apps.maps 10-02 14:11:32.797: W/PackageManager(81): Not granting permission android.permission.DEVICE_POWER to package com.android.deskclock (protectionLevel=2 flags=0x8be45) 10-02 14:11:33.137: D/MediaScannerService(150): done scanning volume external 10-02 14:11:33.197: D/PackageParser(81): Scanning package: /data/app/vmdl257911298.tmp 10-02 14:11:33.837: I/InputReader(81): Device reconfigured: id=0, name='qwerty2', surface size is now 1024x800 10-02 14:11:34.097: D/dalvikvm(81): GC_CONCURRENT freed 12185K, 47% free 13966K/26311K, paused 8ms+23ms 10-02 14:11:36.798: I/TabletStatusBar(124): DISABLE_CLOCK: no 10-02 14:11:36.798: I/TabletStatusBar(124): DISABLE_NAVIGATION: no 10-02 14:11:37.348: I/ARMAssembler(32): generated scanline__00000177:03515104_00001001_00000000 [ 91 ipp] (114 ins) at [0x407c7520:0x407c76e8] in 919320 ns 10-02 14:11:37.598: I/TabletStatusBar(124): DISABLE_BACK: no 10-02 14:11:37.710: I/ActivityManager(81): Displayed com.android.launcher/com.android.launcher2.Launcher: +46s212ms 10-02 14:11:38.817: D/dalvikvm(143): GC_CONCURRENT freed 969K, 8% free 14867K/16007K, paused 4ms+10ms 10-02 14:11:39.437: I/dalvikvm(81): Jit: resizing JitTable from 1024 to 2048 10-02 14:11:40.267: D/dalvikvm(143): GC_FOR_ALLOC freed 2357K, 16% free 14395K/17031K, paused 80ms 10-02 14:11:40.717: D/dalvikvm(143): GC_EXPLICIT freed 742K, 16% free 14358K/17031K, paused 8ms+4ms 10-02 14:11:41.617: D/dalvikvm(81): GC_CONCURRENT freed 1955K, 48% free 13869K/26311K, paused 9ms+10ms 10-02 14:11:42.559: D/dalvikvm(81): GC_CONCURRENT freed 1830K, 48% free 13881K/26311K, paused 9ms+9ms 10-02 14:11:42.758: I/PackageManager(81): Removing non-system package:cz.trilimi.sfaui 10-02 14:11:42.758: I/ActivityManager(81): Force stopping package cz.trilimi.sfaui uid=10036 10-02 14:11:42.967: D/PackageManager(81): Scanning package cz.trilimi.sfaui 10-02 14:11:42.967: I/PackageManager(81): Package cz.trilimi.sfaui codePath changed from /data/app/cz.trilimi.sfaui-1.apk to /data/app/cz.trilimi.sfaui-2.apk; Retaining data and using new 10-02 14:11:42.967: I/PackageManager(81): Unpacking native libraries for /data/app/cz.trilimi.sfaui-2.apk 10-02 14:11:43.097: D/installd(35): DexInv: --- BEGIN '/data/app/cz.trilimi.sfaui-2.apk' --- 10-02 14:11:45.317: D/dalvikvm(391): DexOpt: load 434ms, verify+opt 1260ms 10-02 14:11:45.407: D/installd(35): DexInv: --- END '/data/app/cz.trilimi.sfaui-2.apk' (success) --- 10-02 14:11:45.407: W/PackageManager(81): Code path for pkg : cz.trilimi.sfaui changing from /data/app/cz.trilimi.sfaui-1.apk to /data/app/cz.trilimi.sfaui-2.apk 10-02 14:11:45.407: W/PackageManager(81): Resource path for pkg : cz.trilimi.sfaui changing from /data/app/cz.trilimi.sfaui-1.apk to /data/app/cz.trilimi.sfaui-2.apk 10-02 14:11:45.407: D/PackageManager(81): Activities: cz.trilimi.sfaui.ItemListActivity cz.trilimi.sfaui.ItemDetailActivity 10-02 14:11:45.427: I/ActivityManager(81): Force stopping package cz.trilimi.sfaui uid=10036 10-02 14:11:45.657: I/installd(35): move /data/dalvik-cache/data@[email protected]@classes.dex -> /data/dalvik-cache/data@[email protected]@classes.dex 10-02 14:11:45.657: D/PackageManager(81): New package installed in /data/app/cz.trilimi.sfaui-2.apk 10-02 14:11:45.997: I/ActivityManager(81): Force stopping package cz.trilimi.sfaui uid=10036 10-02 14:11:46.147: D/dalvikvm(143): GC_EXPLICIT freed 3K, 16% free 14356K/17031K, paused 10ms+9ms 10-02 14:11:46.237: D/PackageManager(81): generateServicesMap(android.accounts.AccountAuthenticator): 3 services unchanged 10-02 14:11:46.277: D/PackageManager(81): generateServicesMap(android.content.SyncAdapter): 5 services unchanged 10-02 14:11:46.337: D/PackageManager(81): generateServicesMap(android.accounts.AccountAuthenticator): 3 services unchanged 10-02 14:11:46.347: D/PackageManager(81): generateServicesMap(android.content.SyncAdapter): 5 services unchanged 10-02 14:11:46.437: D/dalvikvm(208): GC_EXPLICIT freed 258K, 7% free 6488K/6919K, paused 3ms+5ms 10-02 14:11:46.477: W/RecognitionManagerService(81): no available voice recognition services found 10-02 14:11:46.897: I/ActivityManager(81): Start proc com.svox.pico for broadcast com.svox.pico/.VoiceDataInstallerReceiver: pid=398 uid=10006 gids={} 10-02 14:11:47.087: I/ActivityThread(398): Pub com.svox.pico.providers.SettingsProvider: com.svox.pico.providers.SettingsProvider 10-02 14:11:47.138: D/GTalkService(174): [GTalkService.1] handlePackageInstalled: re-initialize providers 10-02 14:11:47.147: D/GTalkService(174): [RawStanzaProvidersMgr] ##### searchProvidersFromIntent 10-02 14:11:47.147: D/GTalkService(174): [RawStanzaProvidersMgr] no intent receivers found 10-02 14:11:47.718: I/AccountTypeManager(208): Loaded meta-data for 1 account types, 0 accounts in 186ms 10-02 14:11:48.377: D/dalvikvm(143): GC_CONCURRENT freed 1865K, 15% free 14513K/17031K, paused 7ms+4ms 10-02 14:11:48.917: D/dalvikvm(208): GC_CONCURRENT freed 219K, 6% free 6788K/7175K, paused 7ms+73ms 10-02 14:11:49.207: D/dalvikvm(143): GC_FOR_ALLOC freed 4558K, 31% free 11866K/17031K, paused 89ms 10-02 14:11:49.587: D/dalvikvm(143): GC_CONCURRENT freed 713K, 24% free 13010K/17031K, paused 5ms+4ms 10-02 14:11:49.967: D/dalvikvm(143): GC_CONCURRENT freed 1046K, 19% free 13922K/17031K, paused 5ms+4ms 10-02 14:11:50.437: D/dalvikvm(81): GC_EXPLICIT freed 898K, 47% free 13955K/26311K, paused 6ms+39ms 10-02 14:11:50.467: I/installd(35): unlink /data/dalvik-cache/data@[email protected]@classes.dex 10-02 14:11:50.477: D/AndroidRuntime(227): Shutting down VM 10-02 14:11:50.507: D/dalvikvm(227): GC_CONCURRENT freed 97K, 84% free 331K/2048K, paused 1ms+2ms 10-02 14:11:50.507: I/AndroidRuntime(227): NOTE: attach of thread 'Binder Thread #3' failed 10-02 14:11:50.517: D/jdwp(227): adbd disconnected 10-02 14:11:51.177: D/AndroidRuntime(410): >>>>>> AndroidRuntime START com.android.internal.os.RuntimeInit <<<<<< 10-02 14:11:51.177: D/AndroidRuntime(410): CheckJNI is ON 10-02 14:11:51.897: D/AndroidRuntime(410): Calling main entry com.android.commands.am.Am 10-02 14:11:51.937: I/ActivityManager(81): Force stopping package cz.trilimi.sfaui uid=10036 10-02 14:11:51.937: I/ActivityManager(81): Starting: Intent { act=android.intent.action.MAIN cat=[android.intent.category.LAUNCHER] flg=0x10000000 cmp=cz.trilimi.sfaui/.ItemListActivity } from pid 410 10-02 14:11:51.968: W/WindowManager(81): Failure taking screenshot for (230x179) to layer 21005 10-02 14:11:51.997: I/ActivityManager(81): Start proc cz.trilimi.sfaui for activity cz.trilimi.sfaui/.ItemListActivity: pid=418 uid=10036 gids={} 10-02 14:11:52.007: D/AndroidRuntime(410): Shutting down VM 10-02 14:11:52.057: I/AndroidRuntime(410): NOTE: attach of thread 'Binder Thread #3' failed 10-02 14:11:52.097: D/dalvikvm(410): GC_CONCURRENT freed 98K, 83% free 360K/2048K, paused 1ms+0ms 10-02 14:11:52.097: D/jdwp(410): adbd disconnected 10-02 14:11:53.147: W/ActivityThread(418): Application cz.trilimi.sfaui is waiting for the debugger on port 8100... 10-02 14:11:53.207: I/System.out(418): Sending WAIT chunk 10-02 14:11:53.217: I/dalvikvm(418): Debugger is active 10-02 14:11:53.447: I/System.out(418): Debugger has connected 10-02 14:11:53.457: I/System.out(418): waiting for debugger to settle... 10-02 14:11:53.637: I/ARMAssembler(32): generated scanline__00000177:03515104_00001002_00000000 [ 87 ipp] (110 ins) at [0x407c76f0:0x407c78a8] in 598498 ns 10-02 14:11:53.660: I/System.out(418): waiting for debugger to settle... 10-02 14:11:53.857: I/System.out(418): waiting for debugger to settle... 10-02 14:11:54.057: I/System.out(418): waiting for debugger to settle... 10-02 14:11:54.257: I/System.out(418): waiting for debugger to settle... 10-02 14:11:54.317: V/TLINE(81): new: android.text.TextLine@4155dde8 10-02 14:11:54.467: I/System.out(418): waiting for debugger to settle... 10-02 14:11:54.667: I/System.out(418): waiting for debugger to settle... 10-02 14:11:54.870: I/System.out(418): waiting for debugger to settle... 10-02 14:11:55.027: D/dalvikvm(143): GC_EXPLICIT freed 900K, 16% free 14420K/17031K, paused 7ms+4ms 10-02 14:11:55.067: I/System.out(418): waiting for debugger to settle... 10-02 14:11:55.292: I/System.out(418): debugger has settled (1315) 10-02 14:12:02.008: W/ActivityManager(81): Launch timeout has expired, giving up wake lock! 10-02 14:12:02.971: W/ActivityManager(81): Activity idle timeout for ActivityRecord{4078c6b0 cz.trilimi.sfaui/.ItemListActivity} 10-02 14:12:08.359: D/ExchangeService(320): Received deviceId from Email app: androidc259148960 10-02 14:12:08.507: D/ExchangeService(320): Reconciling accounts... 10-02 14:16:11.437: D/SntpClient(81): request time failed: java.net.SocketException: Address family not supported by protocol 10-02 14:17:21.573: W/jdwp(418): Debugger is telling the VM to exit with code=1 10-02 14:17:21.573: I/dalvikvm(418): GC lifetime allocation: 8642 bytes 10-02 14:17:21.637: D/Zygote(33): Process 418 exited cleanly (1) 10-02 14:17:21.651: I/ActivityManager(81): Process cz.trilimi.sfaui (pid 418) has died. 10-02 14:17:21.847: D/dalvikvm(143): GC_EXPLICIT freed <1K, 16% free 14420K/17031K, paused 7ms+7ms 10-02 14:17:21.917: W/InputManagerService(81): Window already focused, ignoring focus gain of: com.android.internal.view.IInputMethodClient$Stub$Proxy@40bfbf28

  Read the article

• Simple Self Join Query Bad Performance

  - by user1514042

  Could anyone advice on how do I improve the performance of the following query. Note, the problem seems to be caused by where clause. Data (table contains a huge set of rows - 500K+, the set of parameters it's called with assums the return of 2-5K records per query, which takes 8-10 minutes currently): USE [SomeDb] GO SET ANSI_NULLS ON GO SET QUOTED_IDENTIFIER ON GO CREATE TABLE [dbo].[Data]( [x] [money] NOT NULL, [y] [money] NOT NULL, CONSTRAINT [PK_Data] PRIMARY KEY CLUSTERED ( [x] ASC )WITH (PAD_INDEX = OFF, STATISTICS_NORECOMPUTE = OFF, IGNORE_DUP_KEY = OFF, ALLOW_ROW_LOCKS = ON, ALLOW_PAGE_LOCKS = ON) ON [PRIMARY] ) ON [PRIMARY] GO The Query select top 10000 s.x as sx, e.x as ex, s.y as sy, e.y as ey, e.y - s.y as y_delta, e.x - s.x as x_delta from Data s inner join Data e on e.x > s.x and e.x - s.x between xFrom and xTo --where e.y - s.y > @yDelta -- when uncommented causes a huge delay Update 1 - Execution Plan <?xml version="1.0" encoding="utf-16"?> <ShowPlanXML xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xmlns:xsd="http://www.w3.org/2001/XMLSchema" Version="1.2" Build="11.0.2100.60" xmlns="http://schemas.microsoft.com/sqlserver/2004/07/showplan"> <BatchSequence> <Batch> <Statements> <StmtSimple StatementCompId="1" StatementEstRows="100" StatementId="1" StatementOptmLevel="FULL" StatementOptmEarlyAbortReason="GoodEnoughPlanFound" StatementSubTreeCost="0.0263655" StatementText="select top 100&#xD;&#xA;s.x as sx,&#xD;&#xA;e.x as ex,&#xD;&#xA;s.y as sy,&#xD;&#xA;e.y as ey,&#xD;&#xA;e.y - s.y as y_delta,&#xD;&#xA;e.x - s.x as x_delta&#xD;&#xA;from Data s &#xD;&#xA; inner join Data e&#xD;&#xA; on e.x &gt; s.x and e.x - s.x between 100 and 105&#xD;&#xA;where e.y - s.y &gt; 0.01&#xD;&#xA;" StatementType="SELECT" QueryHash="0xAAAC02AC2D78CB56" QueryPlanHash="0x747994153CB2D637" RetrievedFromCache="true"> <StatementSetOptions ANSI_NULLS="true" ANSI_PADDING="true" ANSI_WARNINGS="true" ARITHABORT="true" CONCAT_NULL_YIELDS_NULL="true" NUMERIC_ROUNDABORT="false" QUOTED_IDENTIFIER="true" /> <QueryPlan DegreeOfParallelism="0" NonParallelPlanReason="NoParallelPlansInDesktopOrExpressEdition" CachedPlanSize="24" CompileTime="13" CompileCPU="13" CompileMemory="424"> <MemoryGrantInfo SerialRequiredMemory="0" SerialDesiredMemory="0" /> <OptimizerHardwareDependentProperties EstimatedAvailableMemoryGrant="52199" EstimatedPagesCached="14561" EstimatedAvailableDegreeOfParallelism="4" /> <RelOp AvgRowSize="55" EstimateCPU="1E-05" EstimateIO="0" EstimateRebinds="0" EstimateRewinds="0" EstimatedExecutionMode="Row" EstimateRows="100" LogicalOp="Compute Scalar" NodeId="0" Parallel="false" PhysicalOp="Compute Scalar" EstimatedTotalSubtreeCost="0.0263655"> <OutputList> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="x" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="y" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="x" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="y" /> <ColumnReference Column="Expr1004" /> <ColumnReference Column="Expr1005" /> </OutputList> <ComputeScalar> <DefinedValues> <DefinedValue> <ColumnReference Column="Expr1004" /> <ScalarOperator ScalarString="[SomeDb].[dbo].[Data].[y] as [e].[y]-[SomeDb].[dbo].[Data].[y] as [s].[y]"> <Arithmetic Operation="SUB"> <ScalarOperator> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="y" /> </Identifier> </ScalarOperator> <ScalarOperator> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="y" /> </Identifier> </ScalarOperator> </Arithmetic> </ScalarOperator> </DefinedValue> <DefinedValue> <ColumnReference Column="Expr1005" /> <ScalarOperator ScalarString="[SomeDb].[dbo].[Data].[x] as [e].[x]-[SomeDb].[dbo].[Data].[x] as [s].[x]"> <Arithmetic Operation="SUB"> <ScalarOperator> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="x" /> </Identifier> </ScalarOperator> <ScalarOperator> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="x" /> </Identifier> </ScalarOperator> </Arithmetic> </ScalarOperator> </DefinedValue> </DefinedValues> <RelOp AvgRowSize="39" EstimateCPU="1E-05" EstimateIO="0" EstimateRebinds="0" EstimateRewinds="0" EstimatedExecutionMode="Row" EstimateRows="100" LogicalOp="Top" NodeId="1" Parallel="false" PhysicalOp="Top" EstimatedTotalSubtreeCost="0.0263555"> <OutputList> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="x" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="y" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="x" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="y" /> </OutputList> <RunTimeInformation> <RunTimeCountersPerThread Thread="0" ActualRows="100" ActualEndOfScans="1" ActualExecutions="1" /> </RunTimeInformation> <Top RowCount="false" IsPercent="false" WithTies="false"> <TopExpression> <ScalarOperator ScalarString="(100)"> <Const ConstValue="(100)" /> </ScalarOperator> </TopExpression> <RelOp AvgRowSize="39" EstimateCPU="151828" EstimateIO="0" EstimateRebinds="0" EstimateRewinds="0" EstimatedExecutionMode="Row" EstimateRows="100" LogicalOp="Inner Join" NodeId="2" Parallel="false" PhysicalOp="Nested Loops" EstimatedTotalSubtreeCost="0.0263455"> <OutputList> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="x" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="y" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="x" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="y" /> </OutputList> <RunTimeInformation> <RunTimeCountersPerThread Thread="0" ActualRows="100" ActualEndOfScans="0" ActualExecutions="1" /> </RunTimeInformation> <NestedLoops Optimized="false"> <OuterReferences> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="x" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="y" /> </OuterReferences> <RelOp AvgRowSize="23" EstimateCPU="1.80448" EstimateIO="3.76461" EstimateRebinds="0" EstimateRewinds="0" EstimatedExecutionMode="Row" EstimateRows="1" LogicalOp="Clustered Index Scan" NodeId="3" Parallel="false" PhysicalOp="Clustered Index Scan" EstimatedTotalSubtreeCost="0.0032831" TableCardinality="1640290"> <OutputList> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="x" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="y" /> </OutputList> <RunTimeInformation> <RunTimeCountersPerThread Thread="0" ActualRows="15225" ActualEndOfScans="0" ActualExecutions="1" /> </RunTimeInformation> <IndexScan Ordered="false" ForcedIndex="false" ForceScan="false" NoExpandHint="false"> <DefinedValues> <DefinedValue> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="x" /> </DefinedValue> <DefinedValue> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="y" /> </DefinedValue> </DefinedValues> <Object Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Index="[PK_Data]" Alias="[e]" IndexKind="Clustered" /> </IndexScan> </RelOp> <RelOp AvgRowSize="23" EstimateCPU="0.902317" EstimateIO="1.88387" EstimateRebinds="1" EstimateRewinds="0" EstimatedExecutionMode="Row" EstimateRows="100" LogicalOp="Clustered Index Seek" NodeId="4" Parallel="false" PhysicalOp="Clustered Index Seek" EstimatedTotalSubtreeCost="0.0263655" TableCardinality="1640290"> <OutputList> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="x" /> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="y" /> </OutputList> <RunTimeInformation> <RunTimeCountersPerThread Thread="0" ActualRows="100" ActualEndOfScans="15224" ActualExecutions="15225" /> </RunTimeInformation> <IndexScan Ordered="true" ScanDirection="FORWARD" ForcedIndex="false" ForceSeek="false" ForceScan="false" NoExpandHint="false" Storage="RowStore"> <DefinedValues> <DefinedValue> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="x" /> </DefinedValue> <DefinedValue> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="y" /> </DefinedValue> </DefinedValues> <Object Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Index="[PK_Data]" Alias="[s]" IndexKind="Clustered" /> <SeekPredicates> <SeekPredicateNew> <SeekKeys> <EndRange ScanType="LT"> <RangeColumns> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="x" /> </RangeColumns> <RangeExpressions> <ScalarOperator ScalarString="[SomeDb].[dbo].[Data].[x] as [e].[x]"> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="x" /> </Identifier> </ScalarOperator> </RangeExpressions> </EndRange> </SeekKeys> </SeekPredicateNew> </SeekPredicates> <Predicate> <ScalarOperator ScalarString="([SomeDb].[dbo].[Data].[x] as [e].[x]-[SomeDb].[dbo].[Data].[x] as [s].[x])&gt;=($100.0000) AND ([SomeDb].[dbo].[Data].[x] as [e].[x]-[SomeDb].[dbo].[Data].[x] as [s].[x])&lt;=($105.0000) AND ([SomeDb].[dbo].[Data].[y] as [e].[y]-[SomeDb].[dbo].[Data].[y] as [s].[y])&gt;(0.01)"> <Logical Operation="AND"> <ScalarOperator> <Compare CompareOp="GE"> <ScalarOperator> <Arithmetic Operation="SUB"> <ScalarOperator> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="x" /> </Identifier> </ScalarOperator> <ScalarOperator> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="x" /> </Identifier> </ScalarOperator> </Arithmetic> </ScalarOperator> <ScalarOperator> <Const ConstValue="($100.0000)" /> </ScalarOperator> </Compare> </ScalarOperator> <ScalarOperator> <Compare CompareOp="LE"> <ScalarOperator> <Arithmetic Operation="SUB"> <ScalarOperator> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="x" /> </Identifier> </ScalarOperator> <ScalarOperator> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="x" /> </Identifier> </ScalarOperator> </Arithmetic> </ScalarOperator> <ScalarOperator> <Const ConstValue="($105.0000)" /> </ScalarOperator> </Compare> </ScalarOperator> <ScalarOperator> <Compare CompareOp="GT"> <ScalarOperator> <Arithmetic Operation="SUB"> <ScalarOperator> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[e]" Column="y" /> </Identifier> </ScalarOperator> <ScalarOperator> <Identifier> <ColumnReference Database="[SomeDb]" Schema="[dbo]" Table="[Data]" Alias="[s]" Column="y" /> </Identifier> </ScalarOperator> </Arithmetic> </ScalarOperator> <ScalarOperator> <Const ConstValue="(0.01)" /> </ScalarOperator> </Compare> </ScalarOperator> </Logical> </ScalarOperator> </Predicate> </IndexScan> </RelOp> </NestedLoops> </RelOp> </Top> </RelOp> </ComputeScalar> </RelOp> </QueryPlan> </StmtSimple> </Statements> </Batch> </BatchSequence> </ShowPlanXML>

  Read the article

< Previous Page | 104 105 106 107 108 109 110 111 112 113 114 115  | Next Page >