Search Results

Search found 30252 results on 1211 pages for 'network programming'.

Page 1087/1211 | < Previous Page | 1083 1084 1085 1086 1087 1088 1089 1090 1091 1092 1093 1094  | Next Page >

  • Hard Drive benchmark values show write very very slow

    - by John
    I recently started to have issues with my laptop being very slow. I ran a hard drive benchmarking tool (by ATTO) that showed that the write speed was very very slow on my boot drive. I ran the same benchmark on my usb drive and it was 650 times faster than my boot drive when it came to writing. Reading is very fast/normal on both. I swapped out an identical drive and ran the same benchmark. This time the drive showed proper write speed. Thinking that I had a hard drive going bad I cloned the old one onto the new one. I managed to clone the problem too. Anyone have any ideas on what in WinXP SP3 might be causing the write issues? I am on a corporate network and we have commercial anti-virus software installed. (AVG I think) I regularly run defraggler and have about 40 gig free on a 100 gig drive. The machine has 4 gigs of memory. Any ideas? TIA J

    Read the article

  • Trouble with IIS SMTP relaying to Gmail

    - by saille
    I appreciate that similar questions have been asked about how to setup SMTP relaying with IIS's virtual SMTP server. However I'm still completely stumped on this problem. Here's the setup: IIS 6.0 SMTP server running on Win2k3 box with a NAT'ed IP. Company uses Gmail for all email services. An app on the box needs to send email, so normally we'd just set the app up to talk to smtp.gmail.com directly, but this app doesn't support TLS. Easy, we just setup a local SMTP relay right? So I thought. What we have done so far: Setup IIS SMTP server to relay to smtp.gmail.com, as per these excellent instructions: http://fmuntean.wordpress.com/2008/10/26/how-to-configure-iis-smtp-server-to-forward-emails-using-a-gmail-account/ The local SMTP relay allows anonymous access. Both the local IP and the loopback IP have been explicitly allowed in the Connection and Relay dialogs. Tried sending email from 2 different apps via the local SMTP server, but failed (the emails end up in the Queue folder, but never get sent). The IIS logs show the conversation with the local app, but zero conversation happening with smtp.gmail.com. The port used by gmail is open outbound, and indeed the apps we have that support TLS can send email directly via smtp.gmail.com, so there is no problem with the network. At this point I changed the smtp settings in IIS SMTP server to use a different external SMTP server and hey-presto, the local apps can send email via local IIS SMTP relay. So smtp.gmail.com fails to work with our IIS SMTP relay, but another 3rd party SMTP service works fine. We need to use smtp.gmail.com, so how to troubleshoot this one?

    Read the article

  • Win 2008 R2 - copying TO disk is very slow, copying FROM is more or less okay

    - by avs099
    I have Windows 2008 R2 SP1 with 4 identical SATA disks (Seagate Barracude 7200) in RAID 5 array. It has 4Gb of memory; all recent updates are installed. Problem: when I copy large file from one folder to another, I get about 10MB/s average speed. When I read this file from network share via 1Gbps connection - I get about 25-30 MB/s. Both numbers seems to be low for me - but specifically I'm very frustrated with low write speed. there is no antivirus, no hyper-v, it's just a fileserver - i when i do my tests nobody else reads/write from it (we have only 4 people in a team, so I'm sure). Not sure if that matters, but there is only 1 logic disk "C" with all available space (1400 GB). I'm not an admin at all, so I have no idea where to look and what other information to provide. I did run performance monitor with "% idle time", "avg bytes read", "avg byte write" - here is the screenshot: I'm not sure why there are such obvious spikes. Any idea? Please let me know if you need me to provide more information - what counters should I check, etc. I'm very eager to get this solved. Thank you. UPDATE: we have another Windows 2008 R2 SP1 server with 2 RAID1 arrays - one is disk C (where windows is installed, another one is disk E). It is running Hyper-V and does not have antivirus. I noticed the following behavior when I copy large file (few GBs): C - C: about 50MB/sec C - E: about 55MB/sec E - E: 8MB/sec!!! E - C: 8MB/sec!!! what could cause this?? E drive is RAID1 array from same Seagate Barracuda 1TB drives..

    Read the article

  • Trying to understand Wireless N vs Wireless AC

    - by EGHDK
    Whenever a new wireless standard gets approved you expect faster speeds and longer range. From everything that I've read about it, it seems that AC will only transfer over the 5GHz band and up to 3Gbps. Studying the new AC routers on the market, it seems that they will transfer over 5GHz and 2.4GHz. And 5GHz will only transfer at 1.3Gbps. Which isn't what AC is supposed to be. I know there is a difference between what the standard actually says, and what products will actually do, but is there any reason for this? Is there any other main differences between AC and N? I've heard people discussing AC and saying that it's finally "fixing" what N was supposed to fix... what do they mean by that? Any security benefits? I have seen this image online: Will AC really do that? Will that require an AC network card in my laptop for that to actually happen? Lastly, will the router only be able to communicate with AC devices if I have beamforming technology on? I know it's a ton of questions, but most articles online seem to be outdated, and don't provide too much reliability.

    Read the article

  • Accounting setup in freeradius with mikrotik and the "always" module

    - by Matt
    I have a freeradius setup that is being used to provide authentication for users on a wireless network. The access points are all Mikrotik hardware and the users are connected 24/7. We've been using Daloradius with mysql and freeradius 2. The boss wants to use the accounting information and while this is all set up and appears to be working, I've found that not all the accounting information is present. Since our users may be connected for more than 24 hours at a time we keep this in here, it will reset some attributes daily so that the accounting packets work correctly. So he started poking around at this link: http://wiki.mikrotik.com/wiki/RouterOs_MySql_Freeradius#Configuring_RouterOs_for_Radius_.26_PPP.2A_AAA And was looking specifically at the following section. Since our users may be connected for more than 24 hours at a time we keep this in here, it will reset some attributes daily so that the accounting packets work correctly always fail { rcode = fail } always reject { rcode = reject } always ok { rcode = ok simulcount = 0 mpp = no } However, that link references freeradius 1 and I can't find this in the radius.conf file for freeradius 2. What does it do and could it be a reason I'm missing data? EDIT: I have found one issue. We have a backup freeradius server that is also receiving the accounting packets. Although they are replicating, it's only a master/slave configuration. If the slave receives accounting packets it won't replicate them back to the master. Although I suspect this might solve it, the boss is not convinced due to the always module. Is there anything special I need to configure in the mikrotik AP's or freeradius 2 for clients connected 24/7.

    Read the article

  • Workaround with paths in vista

    - by Argiropoulos Stavros
    Not really a programming question but i think quite relative. I have a .exe running in my windows XP PC. This exe needs a file in the same directory to run and has no problem finding it in XP BUT in Vista(I tried this in several machines and works in some of them) fails to run. I'm guessing there is a problem finding the path.The program is written in basic(Yes i know..) I attach the code below. Can you think of any workarounds? Thank you The exe is located in c:\tools Also the program runs in windows console(It starts but then during the execution cannot find a custom file type .TOP made by the creator of the program) ' PROGRAMM TOP11.BAS DEFDBL A-Z CLS LOCATE 1, 1 COLOR 14, 1 FOR i = 1 TO 80 PRINT "±"; NEXT i LOCATE 1, 35: PRINT "?? TOP11 ??" PRINT " €€‚—‚„‘ ’— ‹„’†‘„— ‘’† „”€„€ ’†‘ ‡€€‘‘†‘ ‰€ † „.‚.‘.€. " COLOR 7, 0 PRINT "-------------------------------------------------------------------------------" PRINT INPUT "ƒ?©« «¦¤ ©¬¤«?©«? ¤???... : ", Factor# INPUT "¤¦£ ¨®e¦¬ [.TOP] : ", topfile$ VIEW PRINT 7 TO 25 file1$ = topfile$ + ".TOP" file2$ = topfile$ + ".T_P" file3$ = "Syntel" OPEN file3$ FOR OUTPUT AS #3 PRINT #3, " ‘¬¤«?©«?? ¤??? = " + STR$(Factor#) + " †‹„‹†€: " + DATE$ CLOSE #3 command1$ = "copy" + " " + file1$ + " " + file2$ SHELL command1$ '’¦ ¨®e¦ .TOP ¤« ¨a­«  £ «¤ ?«a?¥ .T_P OPEN file2$ FOR INPUT AS #1 OPEN file1$ FOR OUTPUT AS #2 bb$ = " \\\ \ , ###.#### ###.#### ####.### ##.### " DO LINE INPUT #1, Line$ Line$ = RTRIM$(LTRIM$(Line$)) icode$ = LEFT$(Line$, 1) IF icode$ = "1" THEN Line$ = " " + Line$ PRINT #2, Line$ PRINT Line$ ELSEIF icode$ = "2" THEN Line$ = " " + Line$ PRINT #2, Line$ PRINT Line$ ELSEIF icode$ = "3" THEN Number$ = MID$(Line$, 3, 6) Hangle = VAL(MID$(Line$, 14, 9)) Zangle = VAL(MID$(Line$, 25, 9)) Distance = VAL(MID$(Line$, 36, 9)) Distance = Distance * Factor# Height = VAL(MID$(Line$, 48, 6)) PRINT #2, USING bb$; icode$; Number$; Hangle; Zangle; Distance; Height PRINT USING bb$; icode$; Number$; Hangle; Zangle; Distance; Height ELSE END IF LOOP UNTIL EOF(1) VIEW PRINT CLS LOCATE 1, 1 PRINT " *** ’„‘ ’“ ‚€‹‹€’‘ *** " END

    Read the article

  • MySQL Workbench is not finding MySQL service? [closed]

    - by PhADDinTraining
    I set up a local MySQL server, currently with no databases. I'm trying to create a new server instance profile in MySQL Workbench to manage the server, and during the Create New Server Instance Profile wizard, it gets to the Windows Management section and tells me that No MySQL service found. I went into Task Manager and found the process mysqld.exe to be running, under the user name of NETWORK SERVICE. Then I went into the Services tab and found that MySQLServerName (I custom named the Windows service) is also there, and status is running. I ran cports and looked at what ports mysqld.exe is using, and ran a telnet command on that port. It's reporting that the port is being listened in on. I then ran the MySQL Command Line Client to be sure, and after \r it gives me a proper connection ID and a list of databases (NONE at this point). But with all this, I can't make the wizard find a running service. I've Googled this and found no answers, so please, if someone would help shed some light on this issue that'd be great!

    Read the article

  • Throughput; capacity planning help for C10K like design

    - by z8000
    I am designing a network service in which clients connect and stay connected -- the model is not far off from IRC less the s2s connections. I could use some help understanding how to do capacity planning, in particular with the system resource costs associated with handling messages from/to clients. There's an article that tried to get 1 million clients connected to the same server [1]. Of course, most of these clients were completely idle in the test. If the clients sent a message every 5 seconds or so the system would surely be brought to its knees. But... How do you do less hand-waving and you know, measure such a breaking point? We're talking about messages being sent by a client over a TCP socket, into the kernel, and read by an application. The data is shuffled around in memory from one buffer to another. Do I need to consider memory throughput ("5 GT/s" [2], etc.)? I'm pretty sure I have the ability to measure the basic memory requirements due to TCP/IP buffers, expected bandwidth, and CPU resources required to process messages. I'm a little dim on what I'm calling "thoughput". Help! Also, does anyone really do this? Or, do most people sort of hand-wave and see what the real world offers, and then react appropriately? [1] http://www.metabrew.com/article/a-million-user-comet-application-with-mochiweb-part-3/ [2] http://en.wikipedia.org/wiki/GT/s

    Read the article

  • Problems with word completion on Windows Mobile

    - by Rowland Shaw
    For "some reason" the word completion function on my windows mobile phone (HTC Diamond, rebadged as a T-Mobile MDA Compact IV (UK) running WM6.1 with HTC Touch Flo 3D) hasn't worked since one of my firends was taking a look at the phone (I remember him bitching about it being too obtrusive for him, as an iPhone fanboy). I've checked all the obvious settings ( Start Input Word Completion ) and everything looks set there; I tried a hard reset, to no avail and even tried upgrading the ROM t the latest from my network provider. I even tried walking into the store where I bought the phone, and the staff couldn't fix the issue. I still have my old handset, which also runs WM6.1 (a T-Mobile MDA Compact III (UK), albeit without Touch Flo 3D), and the word completion works on there, so I'm a little confused as to why I can't get it to work again on my new handset. Can anybody identify why this might not be working, or help me fix it? Edit: Even "Touch Input Settings" has both "Word Completion in T9 mode" and "Word Completion in ABC mode" checked. The full qwerty keyboard option is in T9 mode, and word completion works for this input method; It still does not work for my preferred, "Letter Recogniser" method.

    Read the article

  • Where do I define a group policy that will set a users desktop background color to green the first time they log in?

    - by Tyler
    Servers: W2k8 R2 x64 Desktops: Win7 Pro x64 Our current group policy uses a custom ADM file to define certain properties of the desktop (Background Image (centered), Background Color is green (00 74 00)). This policy works for us, but the down-side is that policies defined in our custom ADM are only applied after a GPUpdate /Force is applied. We would like these desktop theme settings to be applied the first time the user logs onto the computer. I've been working on a new policy that forces the computer to wait for the network when the user logs on to handle folder redirection. The reason for writing the new policy was to resolve the issue that a user needs to run GPupdate /Force the first time they log in, so it doesn't make sense for me to implement the new policy if there is still something that requires GPUpdate /Force to get the user in the state that we want them. I've moved the setting for background image out into Admin Templates- Desktop- Desktop- "Desktop Wallpaper" so this is now being set properly when the user first logs in. Now I'm left with a black background until I force a group policy update. I have tried to play around with setting a default "Theme" and had limited success; this was not reliable enough to call a solution. I suppose I could set the background color with a script? Any thoughts? It feels like I'm missing something obvious, or that this should be much easier than it is.

    Read the article

  • Why can't I copy .zip files from a server to a server in a different domain?

    - by Kyralessa
    At work, we're using a Windows Server 2008 R2 VM as our build server. At the end of the build process for any of our projects, we copy the packaged deployment files to a folder on the server where they'll be deployed. (This is done in a batch command by a service account.) For most of our projects, which deploy to a Windows Server 2008 R2 VM, this step goes swimmingly. But for one project, which deploys to a Windows Server 2003 R2 VM which resides in a different domain on our network, the .zip files return "Access is denied" and don't copy, though all of the other files copy correctly. Our sysadmins say they haven't prevented this in group policy or by other means. If I'm logged in the build server as myself and run the copy in the command window, I can't copy the .zip files over either, so it's not just a matter of the service account's permissions. If I log into the 2003 server and then copy from the build server to the 2003 server, using the command window, it works, whether I run as myself or as our service account. Only .zip files cause the "Access is denied" problem. Even a (fake) .exe file copies correctly. All of our other projects have .zip files, and they copy to their 2008 R2 server correctly. Is there a way I can get the Windows Server 2003 R2 VM to accept .zip files copied from our build server?

    Read the article

  • SBS 2011 Essentials and too many new Mac users

    - by Harry Muscle
    We currently have about 15 users on a Windows SBS 2011 Essentials Server. I've just been informed that we plan to bring aboard about 15 more users that will be using Macs. We'll be using a Mac Server to manage the 15 new Macs, however, I'm looking for advice on how to best set this all up. Ideally I would just add the 15 new Mac users to Active Directory and setup the Mac Server to authenticate against AD, unfortunately the SBS 2011 Essentials Server has a limit of 25 users, so adding these new users to AD won't work unless we upgrade the Windows server (which I'd rather avoid since it's a lot of work and a lot of money). That leaves the option of creating user accounts for these 15 Mac users on the Mac Server only. The problem that this creates though is how do I share files been Mac users and Windows users since they are now using different systems for network authentication. Any advice (short of upgrade to SBS Standard) is highly appreciated. Thanks, Harry P.S. We don't run Exchange or anything else on our server ... it's mainly used for file sharing and enforcing security via group policies.

    Read the article

  • NTOP gives warnings on startup

    - by FR6
    I just installed ntop 1.4.4 and when I start it, it give me infinite warnings "packet truncated": ... RRD_DEBUG: umask 0066 RRD_DEBUG: DirPerms 0700 THREADMGMT: RRD: Started thread (t2992630672) for data collection THREADMGMT[t2992630672]: RRD: Data collection thread starting [p30923] INIT: Created pid file (/var/run/ntop.pid) THREADMGMT[t3086329552]: ntop RUNSTATE: INITNONROOT(3) Now running as requested user 'nobody' (99:99) Note: Reporting device initally set to 0 [eth0] (merged) THREADMGMT[t3086329552]: ntop RUNSTATE: RUN(4) THREADMGMT[t2982140816]: NPS(1): Started thread for network packet sniffing [eth0] THREADMGMT[t2982140816]: NPS(eth0): pcapDispatch thread starting [p30923] THREADMGMT[t2982140816]: NPS(eth0): pcapDispatch thread running [p30923] THREADMGMT[t3047009168]: SIH: Idle host scan thread running [p30923] THREADMGMT[t3057499024]: SFP: Fingerprint scan thread running [p30923] **WARNING** packet truncated (8814->8232) **WARNING** packet truncated (10274->8232) **WARNING** packet truncated (8814->8232) **WARNING** packet truncated (8814->8232) ... Do I need to configure something? I tried to access the web interface (http://localhost:3000) but it does not work. Note: I'm on CentOS. EDIT: Not sure if it helps but there is my "ifconfig": eth0 Link encap:Ethernet HWaddr 00:16:76:BC:7E:77 inet addr:192.168.0.221 Bcast:192.168.0.255 Mask:255.255.255.0 inet6 addr: fe80::216:76ff:febc:7e77/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:15496640 errors:0 dropped:0 overruns:0 frame:0 TX packets:19256813 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:836230629 (797.4 MiB) TX bytes:608496148 (580.3 MiB) Memory:dffe0000-e0000000

    Read the article

  • debian VM refusing all traffic apart from http

    - by james lewis
    I've got a VM with a fresh install of Debian (wheezy) and I've installed node and mongo on it. The VM is using a bridged network connection so I was expecting to be able to point my host machines browser at the ip address of the Debian VM (port 1337 for my node example or port 28017 for my mongo status page) and see one of the two services (node or mongo). My requests are refused though. As far as I can tell Debian allows all traffic by default and you have to manually configure iptables to drop traffic. I've checked iptables and it says it's setup to allow anything through. It looks like this: root@devbox:/home/jlewis# iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination As a test I setup nginx and I was able to get to the nginx landing page from my host no problems so obviously http traffic is allowed. I then set nginx up to forward all traffic upstream to mongo - no problems there, I was able to see the status page. I then did the same for my example node server and again, no problems. So http traffic is fine, but all other traffic is blocked. Anyone know why debian might be refusing all other traffic other than iptables being setup to drop it? EDIT - output from netstat -nltp: Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 127.0.0.1:28017 0.0.0.0:* LISTEN 1762/mongod tcp 0 0 0.0.0.0:51028 0.0.0.0:* LISTEN 1541/rpc.statd tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN 2462/sshd tcp 0 0 127.0.0.1:1337 0.0.0.0:* LISTEN 2794/node tcp 0 0 127.0.0.1:25 0.0.0.0:* LISTEN 2274/exim4 tcp 0 0 127.0.0.1:27017 0.0.0.0:* LISTEN 1762/mongod tcp 0 0 0.0.0.0:111 0.0.0.0:* LISTEN 1510/rpcbind tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN 2189/nginx tcp6 0 0 :::22 :::* LISTEN 2462/sshd tcp6 0 0 :::45335 :::* LISTEN 1541/rpc.statd tcp6 0 0 ::1:25 :::* LISTEN 2274/exim4 tcp6 0 0 :::111 :::* LISTEN 1510/rpcbind

    Read the article

  • Strange IIS hits originating from Trend Micro

    - by TesterTurnedDeveloper
    I'm trying to trace thru an error on a extranet site I maintain. I've had a look thru the logs, and I'm seeing hits originate from these IP addresses: 216.104.15.130 216.104.15.138 216.104.15.142 216.104.15.13 150.70.84.49 150.70.84.44 Network-tools.com gives 'TREND MICRO INCORPORATED' as the owner of all these IPs. The hits fail as they aren't sending any cookies (therefore aren't considered logged in). The hits are to pages containing URLs that only the logged in user would see, i.e. ImageEdit.aspx?ImageId=467424. I.e. the server isn't guessing these URLs, someone would have to log into the site to know these URLs exist. Theory: the Trend Antivirus client grabs URLs and sends them to the server for 'extra processing'? Googling around gives me this: http://www.forumpostersunion.com/showthread.php?p=51272 - where people are reporting comment spam from these addresses. The articles says their servers have been hacked (a few months ago, presumably fixed now?). A hacked server wouldn't explain how the URLs have been plucked off the user's PCs. Has anyone seen this before? Anything nefarious going on here?

    Read the article

  • CryptSvc not matched by Windows 7 Firewall rule

    - by theultramage
    I am using Windows Firewall in conjunction with a third-party tool to get notified about new outbound connection attempts (Windows Firewall Notifier or Windows Firewall Control). The way these tools do it is by setting the firewall to deny by default, and to add an auditing policy to log blocked connections into the Security event log. Then they watch the log, and display notification about newly added entries. netsh advfirewall set allprofiles firewallpolicy blockinbound,blockoutbound auditpol /set /subcategory:{0CCE9226-69AE-11D9-BED3-505054503030} /failure:enable With this configuration in place, I now need to craft outbound allow rules for applications and system services. Here is the rule for CryptSvc, the service frequently used for certificate validation and revocation checking: netsh advfirewall firewall add rule name="Windows Cryptographic Services" action=allow enable=yes profile=any program="%SystemRoot%\system32\svchost.exe" service="CryptSvc" dir=out protocol=tcp remoteport=80,443 The problem is, this rule does not work. Unless I change the scope to "all programs and services" (which is really unhealthy), connection denied events like the following will keep appearing in the security log: Event 5157, Microsoft Windows security auditing. The Windows Filtering Platform has blocked a connection. Application Information: Process ID: 1476 (<- svchost.exe with CryptSvc and nothing else) Application Name: \device\harddiskvolume1\windows\system32\svchost.exe Network Information: Direction: Outbound Source Address: 192.168.0.1 Source Port: 49616 Destination Address: 2.16.52.16 Destination Port: 80 Protocol: 6 (<- TCP) To make sure it's CryptSvc, I have let the connection through and reviewed its traffic; I also configured CryptSvc to run in its own svchost instance to make it more obvious: ;sc config CryptSvc type= share sc config CryptSvc type= own So... why is it not matching the firewall rule, and how to fix that?

    Read the article

  • really weird DNS problem in Ubuntu {after one month, seems like ISP problem}

    - by OmniWired
    Hello everyone. I been having this random dns problem, in Ubuntu 10.04 and in 10.10 it started about 2 weeks ago after (I believe) an update. Basically when I go to a website randomly I get that the website I'm visiting is not available ("Oops! Google Chrome could not connect to ..." & "This webpage is not available."). I tested with Chromium "7.0.515.0 (58587)" and Firefox minefield (4.0ish) and 3.6.9. I did these 4 things already: /etc/default/grub GRUB_CMDLINE_LINUX="ipv6.disable=1" and this: /etc/sysctl.conf net.ipv6.conf.all.disable_ipv6 = 1 net.ipv6.conf.default.disable_ipv6 = 1 net.ipv6.conf.lo.disable_ipv6 = 1 *disabling Chromium DNS pre-fetching *using Google and OpenDNS servers as well as ISP DNS servers. But didn't improve, also no other computers in my network have the same problem. All computer wired to the same router. I'm a software engineer that run out of ideas, please help me. Thanks in advance. UPDATE: some programs (synaptic / firefox update/ vuze(azureus)) say connection refused for the error. Most of the time a second try will fix the "refusal". UPDATE2: I found out with Wireshark, that everytime I have this problem i've got this 192.168.0.10 8.8.8.8 ICMP Destination unreachable (Port unreachable) Confirmed an ISP error. ISP;Speedy Location: Argentina, Buenos Aires (capital Federal) Area.

    Read the article

  • Windows 7 Folder Redirection (GPO)

    - by Kev
    I have been fighting this issue for a day or two now, so I am looking for some insight. I am taking over admin duties in a domain of 800 users, and the previous admins really did not employ much of any GPO settings for the clients of the Domain. In each site, there is a location on the file server where "Home" folders were manually created. EX: \server\home\enduser Whenever a user got a machine, the admin would manually right-click on the "My Documents" folder and manually enter the path to the home folder. We are planning to start putting Windows 7 machines on the Network, and I am wanting to automate as much as I can, everything that was not done in the past. Since everyone has exising "Home" folders I have been fighting and trying to get Folder Redirection to work with a new Windows 7 machine (In a Test OU). I am getting all kinds of errors and I can't get the Windows 7 "Documents" folder to redirect to the users EXISTING home folders. As I stated earlier, all of the Home folders were (and still are) manually created on the File Server and are set with the following Security permissions - Domain Admins - Full Control euser (end user) - Modify (Everything but Full) Can someone point me in the right direction on the proper setting to put in the Folder Redirection GPO to get this to work with the Existing Home folders.

    Read the article

  • Sonicwall TZ210 - Set up public wifi on separate subnet & interface

    - by thomasjbarrett
    I want to set up a public wifi by connecting another router to the X6 interface, and put it on a separate subnet (192.168.10.0/24) & in the DMZ Zone to keep it away from the regular LAN. I believe I have the network settings correct: the router has acquired the IP and DNS information from the TZ210, and the TZ210 shows it as an active DHCP lease. X6 is in the DMZ. I now have a routing/NAT/firewall problem, since I can't get any traffic to travel from the subnet to the internet. I can't get to any external websites and can't ping the TZ210 from the subnet. X0 is the regular LAN, and X1 is the WAN. Looking for any tips or tutorials on this. Here's my current relevant rules: Routing Source: X6 Subnet Destination: Any Service: Any Gateway: Default Gateway Interface: X6 Source: Any Destination: X6 Subnet Service: Any Gateway: 0.0.0.0 Interface: X6 NAT Policies Source Original: Any Translated: WAN IP Destination Original: Any Translated: Original Inbound: X6 Outbound: X1 Source Original: Any Translated: U0 IP Destination Original: Any Translated: Original Inbound: X6 Outbound: U0 Firewall DMZ LAN : Deny All DMZ WAN : Allow All LAN DMZ : Allow All WAN DMZ : Allow All

    Read the article

  • How to backup a NAS drive to a USB drive?

    - by Tim Murphy
    How would you backup 600+ GB of data on a NAS (Network-Attached Storage) drive to a USB external drive? The NAS drive does not contain mission critical data nonetheless I wish to make weekly copies of it just in case. The NAS drive is almost exclusively used as an archive dump and is rarely updated. However the backup strategy used must have a simple restore procedure so I can confidently say the data now on the NAS drive is exactly how it was at the time of backup. I did try xcopy but seemed like it would take many-many hours and eventually crashed with insufficient memory. http://www.ctunion.com/node/114 suggests I would need to use xxcopy instead due to folder/file name lengths. My concern with xcopy/xxcopy is the length of time it takes. Hoping something else is faster. NAS drive is DLink DNS-313. 1TB drive installed. Connected to router via Ethernet cable. USB drive is Seagate 1TB. Can be connected to Windows Vista (preferred) or Windows 7 PCs. Both PCs are usually connected Wirelessly however ethernet cable can be used during backup to speed up the process.

    Read the article

  • samba "username map" stopped to work after upgrade to 3.6

    - by Kris_R
    It was time to upgrade our group server (new HDs, problems with old installation of DRBD, etc..). Going as usually for CentOS i upgraded whole system from 6.3 to 6.4 The later one came with samba 3.6 as the old one was 3.5. I transferred most of users by copying /etc/password, /etc/shadow and samba accounts with pdbedit. Homes were on nfs-drive. The translation of unix accounts to samba accounts are located in /etc/samba/smbusers. Strangely enough on some windows clients there was problem to connect to samba-shares. In one case the only thing that worked was, instead of giving windows name, to use the unix account. In another one, it was possible to mount network drive and to open it in Windows Explorer, however other applications like "Total commander" at the attempt of opening this drive gave the message "Cannot connect to z:" (sometimes at this moment user/pass were requested). The smb.conf has following entries: [global] security = user passdb backend = tdbsam username map = /etc/samba/smbusers ... [Kris] comment = Kris's Private path = /SMB/Users/Kris writeable = yes read only = no browseable = yes users = krisr printable = no security mask = 0777 force security mode = 0 directory security mask = 0777 force directory security mode = 0 force create mode = 0775 force directory mode = 6775 The smbusers: # Unix_name = SMB_name1 SMB_name2 ... krisr = Kris Of course testparm runs without any errors. I was used from samba 3.5 to outputs of form Mapped user kris to krisr. Nothing like this happens now. Just message check_sam_security: Couldn't find user Kris in passdb. I read on web that some guys had problem with 3.6 and security = ADS, but these were not helpful for me. I'm seriously thinking about downgrading back to samba 3.5 but before this step I wanted to ask if somebody knows the solution of these problems.

    Read the article

  • Cisco QoS Guidance

    - by Kyle Brandt
    I have a 10M connection to the internet that is hooked into a 100M port. I am getting started with QoS, and am hopping for a little guidance on setting it up on a Cisco 3825 router. Right now I am going forward with the idea that I have to implement it on my router, and the provider can't provide QoS for me. How I envision it working is that the QoS will drop or queue packets on my router and that will help prevent a situation where the provider has to start dropping a lot of packets. Right now all I am tasked with is making sure that one of the 3 LANs gets a certain slice (say 3M for Gig Lan1) of the 10M internet connection (But ideally this will be more flexible in the Future). 10M Internet on 100M port on HWIC-4ESW +-----------------------+ | | Gig Lan1 | Cisco 3825 | Lan3 on HWIC-4ESW | | +-----------------------+ Gig Lan2 I need to learn more about QoS, but having a target technology and maybe example configuration will help me wrap my head around the reading I am doing a little more. Which Cisco QoS Technology do you recommend for this particular situation? Have a basic sample config of how this might work? Right now the 10M line is not congested, so this more to have something in place in case it starts to become mildly congested in the future. I do have VOIP at one location connected to this one over the Internet that goes through a VPN tunnel. Everything else that is between this location and other offices is on a separate MPLS network.

    Read the article

  • Can I setup a test server and then transfer everything to a diff. production server?

    - by Justin
    Hello, I am going to be setting up a "real" server, but it's not being shipped for another week. I was planning on setting up most of the server's functionality using an extra workstation I have. I wanted to set-up Windows Server 2003 or 2008, IIS, Terminal Services, Firewall, and Antivirus on this regular machine. I'd also be installing software like Winzip and VMWare that'll be used on the server. I can't ghost the machine, as far as I've done in the past, because the motherboard/cpu/etc. will all be different. Is there any way to export all of the "server settings" or something like that so I can move everything from test to production? Is there any software out there that does something similar to this? Some things I'm going to have to wait on such as setting up the file server completely in its raid configuration, but I'd like to get the simple server stuff and network setup out of the way. Has anyone done this before? Do I need software, open-source or not, to do this? Or maybe there's a way to export all the server settings in some way? Thanks in advance! Justin

    Read the article

  • virtualisation with kvm: export services from guest to the host

    - by ascobol
    Hello, I would like to export some services from the guest os to the host os, via kvm, and by the same way learn some things about networking. I have tried the following commands: In the host (kubuntu 10.4): $ sudo tunctl -u ascobol Set 'tap0' persistent and owned by uid 2401 $ sudo ifconfig tap0 192.168.2.1 netmask 255.255.255.0 broadcast 192.168.2.255 The ifconfig command returns: $ /sbin/ifconfig tap0 Link encap:Ethernet HWaddr 3e:4e:e3:cc:bc:92 inet addr:192.168.2.1 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::3c4e:e3ff:fecc:bc92/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:17 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) $ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 tap0 Then I run the virtual machine (ubuntu server 10.4): $ sudo kvm -hda ubuntuserver104.qcow2 -net nic -net tap,name=tap0,script=no (I'm using sudo because without it fails with the following message:) warning: could not configure /dev/net/tun: no virtual network emulation With sudo the virtual machine boots, I just get this message: pci_add_option_rom: failed to find romfile "pxe-rtl8139.bin" In the virtual machine: $ ifconfig eth0 192.168.2.2 netmask 255.255.255.0 broadcast 192.168.2.255 Now if I run: $ ssh 192.168.2.2 I just get a No route to host What is wrong with this setup ? Thanks !

    Read the article

  • Route all traffic via OpenVPN client

    - by Ilya
    I've got OpenVPN client running on 192.168.0.3. What I'd like to do is route all the traffic from the second computer with 192.168.0.100 via OpenVPN client that's running on the first computer. My router ip is 192.168.0.1 Network topology: Windows computer with OpenVPN client: 192.168.0.3 Windows computer whose traffic has to be rerouted: 192.168.0.100 Router: 192.168.0.1 I want it to work in the following way: 192.168.0.100 computer => 192.168.0.3 computer => OpenVPN => 192.168.0.1 How can I achieve that by only modifying windows' routing table? I've tried entering the following into windows shell(on computer without VPN), which didn't work (it just dropped my internet connection): route delete 0.0.0.0 mask 255.255.255.255 192.168.0.1 route add 0.0.0.0 mask 255.255.255.255 192.168.0.3 Should I also setup the computer that has OpenVPN client running? Does it have anything to do with windows tcp forwarding? Thanks!

    Read the article

< Previous Page | 1083 1084 1085 1086 1087 1088 1089 1090 1091 1092 1093 1094  | Next Page >