Search Results

Search found 5137 results on 206 pages for 'i like traffic lights'.

Page 109/206 | < Previous Page | 105 106 107 108 109 110 111 112 113 114 115 116  | Next Page >

• IPv6 link-local routing

  - by singpolyma

  "Routers do not forward packets with link-local addresses." says Wikipedia (http://en.wikipedia.org/wiki/Link-local_address) What I want to know is: that makes sense if the destination is a link-local address, but what if I have a box that only has a link-local address trying to reach a global/site scope address? Can the traffic make it back, or will that fail because the return packets will be to a link-local address?

  Read the article

• PPTP VPN Not Working - Peer failed CHAP authentication, PTY read or GRE write failed

  - by armani

  Brand-new install of CentOS 6.3. Followed this guide: http://www.members.optushome.com.au/~wskwok/poptop_ads_howto_1.htm And I got PPTPd running [v1.3.4]. I got the VPN to authenticate users against our Active Directory using winbind, smb, etc. All my tests to see if I'm still authenticated to the AD server pass ["kinit -V [email protected]", "smbclient", "wbinfo -t"]. VPN users were able to connect for like . . . an hour. I tried connecting from my Android phone using domain credentials and saw that I got an IP allocated for internal VPN users [which I've since changed the range, but even setting it back to the initial doesn't work]. Ever since then, no matter what settings I try, I pretty much consistently get this in my /var/log/messages [and the VPN client fails]: [root@vpn2 ~]# tail /var/log/messages Aug 31 15:57:22 vpn2 pppd[18386]: pppd 2.4.5 started by root, uid 0 Aug 31 15:57:22 vpn2 pppd[18386]: Using interface ppp0 Aug 31 15:57:22 vpn2 pppd[18386]: Connect: ppp0 <--> /dev/pts/1 Aug 31 15:57:22 vpn2 pptpd[18385]: GRE: Bad checksum from pppd. Aug 31 15:57:24 vpn2 pppd[18386]: Peer armaniadm failed CHAP authentication Aug 31 15:57:24 vpn2 pppd[18386]: Connection terminated. Aug 31 15:57:24 vpn2 pppd[18386]: Exit. Aug 31 15:57:24 vpn2 pptpd[18385]: GRE: read(fd=6,buffer=8059660,len=8196) from PTY failed: status = -1 error = Input/output error, usually caused by unexpected termination of pppd, check option syntax and pppd logs Aug 31 15:57:24 vpn2 pptpd[18385]: CTRL: PTY read or GRE write failed (pty,gre)=(6,7) Aug 31 15:57:24 vpn2 pptpd[18385]: CTRL: Client 208.54.86.242 control connection finished Now before you go blaming the firewall [all other forum posts I find seem to go there], this VPN server is on our DMZ network. We're using a Juniper SSG-5 Gateway, and I've assigned a WAN IP to the VPN box itself, zoned into the DMZ zone. Then, I have full "Any IP / Any Protocol" open traffic rules between DMZ<--Untrust Zone, and DMZ<--Trust Zone. I'll limit this later to just the authenticating traffic it needs, but for now I think we can rule out the firewall blocking anything. Here's my /etc/pptpd.conf [omitting comments]: option /etc/ppp/options.pptpd logwtmp localip [EXTERNAL_IP_ADDRESS] remoteip [ANOTHER_EXTERNAL_IP_ADDRESS, AND HAVE TRIED AN ARBITRARY GROUP LIKE 5.5.0.0-100] Here's my /etc/ppp/options.pptpd.conf [omitting comments]: name pptpd refuse-pap refuse-chap refuse-mschap require-mschap-v2 require-mppe-128 ms-dns 192.168.200.42 # This is our internal domain controller ms-wins 192.168.200.42 proxyarp lock nobsdcomp novj novjccomp nologfd auth nodefaultroute plugin winbind.so ntlm_auth-helper "/usr/bin/ntlm_auth --helper-protocol=ntlm-server-1" Any help is GREATLY appreciated. I can give you any more info you need to know, and it's a new test server, so I can perform any tests/reboots required to get it up and going. Thanks a ton.

  Read the article

• cluster live postgres 8.3 server

  - by bobinabottle

  Our web application is getting more and more traffic, which is making our poor pg8.3 database server have a little trouble keeping up. I've had a look into using pgpool II for clustering the db to relieve a little strain, and I was wondering how this should be done to minimise downtime considering I would be clustering a live database. Has anyone had experience with this or know of any guides to follow? Cheers :)

  Read the article

• Command to find out which machines I share a network with

  - by BlackIce

  Can I find out which other machines (their IPs) are on my network via Ubuntu command line? What I currently do is install Wireshark and monitor the traffic. Was just hoping there was a simpler way of doing this.

  Read the article

• Is there an encrypted udp based tunnel that doesn't need a tun/tap device?

  - by kbyrd

  I am looking for a tunneling solution that behaves a similar to an ssl or ssh tunnel but over UDP. One the client end, OpenVPN provides an network interface. I want the client end to just listen on a local port and forward all that traffic over the tunnel it has established.

  Read the article

• How to make `rm` faster on ext3/linux?

  - by depesz

  I have ext3 filesystem mounted with default options. On it I have some ~ 100GB files. Removal of any of such files takes long time (8 minutes) and causes a lot of io traffic, which increases load on server. Is there any way to make the rm not as disruptive?

  Read the article

• Apache log showing NAT server address instead of real requester IP

  - by thaBadDawg

  My Apache server is behind a firewall with a NAT translation. The problem I'm having is that I want to see who is actually making the request instead of my firewall's address. It's nice to know that the firewall is working, but to really look at traffic patterns I need to see the real world IP address.

  Read the article

• Do all web caches understand the "Cache-Control" HTTP header?

  - by chris_l

  I'd like to avoid the "Expires" header, and use "Cache-Control" only - or maybe the other way around. The headers will account for a significant percentage of my traffic, so I'd prefer not to "use both". AFAIK, the "Cache-Control" header was standardized in HTTP 1.1, but are there still web caches/proxies in use, which don't understand it? Note: This could help answering a part of my stackoverflow (bounty) question

  Read the article

• What's port 1283?

  - by kbluck

  I see a lot of connection attempts to 1283/tcp on my firewall from a client computer to a Windows Server 2008 Domain Controller. What exactly is this traffic? Something to do with NetBIOS, perhaps?

  Read the article

• List Squid's internal ip:port to external ip:port mapping table

  - by joshperry

  I'm assuming that squid keeps a list of internal ip:port that a request is made on and the matching external ip:port that the request is fulfilled with. In the case of a long transfer, such as a file download, it would be nice to be able to see which internal ip:port is downloading the file. I am able to see the traffic and get the external ip:port that squid is using easily with tcpdump or iptraf but I can't find a way to map this back to an internal ip:port.

  Read the article

• How do I configure dual WAN links for failover on a Cisco 891?

  - by Donjo

  I have a Cisco 891 that is going to be connected to 2 WAN links, a DSL connection and a cable connection. I'm not so concerned with load balancing between them because the DSL connection speed is a drop in the bucket when compared to the cable speed though it would be nice if it worked that way. I mainly just want to force all traffic through the cable WAN link unless it goes down. I'm not really sure what feature set I should be researching.

  Read the article

• Pros and Cons of Creating an Internal Cerificate Authority

  - by Chad

  What are the pros and cons of spinning up an internal certificate authority (primarily Windows 2003 CA)? We have the need to encypt server-server traffic on a project that has 20+ certificates. We could buy certs from Verisign, but I was thinking that an internal CA might be a better long term solution. So I was looking to the community to provide a pros/cons list of what we might gain (or lose) by hosting our own CA? Thanks in advance for the help.

  Read the article

• How to setup a work -> home -> internet http tunneling service

  - by Konstantinos

  I want to know which program is recommended in order to setup such as scenario, ie accessing the internet from work or other places that traffic is monitored by installing a http tunneling service in a home computer. Thanks in advance for any input. edit: Is it possible to achieve the same by installing a home proxy?

  Read the article

• Port forwarding using a BT Home Hub 2.0 (Supplied to new BT Infinity Customers in the UK)

  - by Jasarien

  I don't usually have trouble with port forwarding, I've been able to do it successfully on a number of different routers, including Linksys, Belkin, Netgear and Apple (Time Capsule / Airport Extreme). So I'm quite confused here. I had been using my Apple Time Capsule as my router for a few years now, with several port mappings all working fine. But it died recently, so I've had to resort to using the BT Home Hub 2.0 that was supplied with my BT Infinity broadband subscription. The forwarding interface for the Home Hub is simplified for the most part, allowing you to select an application or game and assign it to a particular computer on the network which you choose from a list that the Home Hub has 'discovered'. My Mac Pro has a manually assigned static IP 192.168.1.4 and my router is static at 192.168.1. I have chosen SSH from the list of applications and assigned it to my Mac Pro (the only computer in the list currently). The Home Hub also has a feature to keep a DNS service updated, and I have set it to keep my external IP address updated on my hostname. This is how I had it setup in the past with other routers and not had trouble before. I am able to ping my hostname (and external IP) from outside the network and get a response. But when I try to connect using SSH, the connection times out. The Home Hub also has "Firewall settings". The currently selected setting is: Default: Allow all outgoing connections and block all incoming traffic. Games and application sharing is allowed. But I've tried changing it to: Disabled: All traffic is allowed to pass through your BT Home Hub to your devices. Note: you’ll still need to use the games and application sharing feature to make sure that certain applications work properly. And the connection still times out... So frustrating. The OS X firewall on my Mac is disabled, so I don't think that's in the way. I have tried setting the port forwarding manually, instead of relying on the preset "SSH" option (incase it's not using the port I expect). So I set up my own "application" (as the Home Hub calls it) and forwarded external port 22 TCP to internal port 22 TCP to 192.168.1.4 - but that just gives the same result - unable to connect. Next, with the router's firewall disabled and OS X's firewall disabled, I ran the Shields Up test (https://www.grc.com/x/ne.dll?bh0bkyd2) and the result was that all my service ports (0 - 1055) are in 'Stealth' mode. I.e. nothing even exists at my IP as far as any outsider is concerned... Strange. The only thing that seems to work is setting my Mac Pro as the DMZ - which I don't want to do for obvious reasons. Any help with this would be extremely appreciated, thanks.

  Read the article

• Cisco IOS QoS prioritize SSH but not SCP

  - by ensnare

  How can I prioritize ssh traffic to ensure low-latency but throttle SCP file transfers? I'm looking for a solution that is not host specific so I don't have to add lists of IP addresses. Thanks!

  Read the article

• Setup a vpn server with a static IP with NAT and port forwarding

  - by Lorenzo Pistone

  I have a Debian VPS with an assigned static IP. I want to setup a virtual interface (with an ip like 192.168..) on my laptop (Ubuntu, dynamic IP) linked to the remote VPS, so that if I bind sockets to it the traffic is tunneled to the VPS and sent to the Internet from there. Port forwarding must be available. This looks like a job for a VPN software, but I'm clueless about the pieces of software needed. Any advice?

  Read the article

• SSL support with Apache and Proxytunnel

  - by whuppy

  I'm inside a strict corporate environment. https traffic goes out via an internal proxy (for this example it's 10.10.04.33:8443) that's smart enough to block ssh'ing directly to ssh.glakspod.org:443. I can get out via proxytunnel. I set up an apache2 VirtualHost at ssh.glakspod.org:443 thus: ServerAdmin [email protected] ServerName ssh.glakspod.org <!-- Proxy Section --> <!-- Used in conjunction with ProxyTunnel --> <!-- proxytunnel -q -p 10.10.04.33:8443 -r ssh.glakspod.org:443 -d %host:%port --> ProxyRequests on ProxyVia on AllowCONNECT 22 <Proxy *> Order deny,allow Deny from all Allow from 74.101 </Proxy> So far so good: I hit the Apache proxy with a CONNECT and then PuTTY and my ssh server shake hands and I'm off to the races. There are, however, two problems with this setup: The internal proxy server can sniff my CONNECT request and also see that an SSH handshake is taking place. I want the entire connection between my desktop and ssh.glakspod.org:443 to look like HTTPS traffic no matter how closely the internal proxy inspects it. I can't get the VirtualHost to be a regular https site while proxying. I'd like the proxy to coexist with something like this: SSLEngine on SSLProxyEngine on SSLCertificateFile /path/to/ca/samapache.crt SSLCertificateKeyFile /path/to/ca/samapache.key SSLCACertificateFile /path/to/ca/ca.crt DocumentRoot /mnt/wallabee/www/html <Directory /mnt/wallabee/www/html/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> <!-- Need a valid client cert to get into the sanctum --> <Directory /mnt/wallabee/www/html/sanctum> SSLVerifyClient require SSLOptions +FakeBasicAuth +ExportCertData SSLVerifyDepth 1 </Directory> So my question is: How to I enable SSL support on the ssh.glakspod.org:443 VirtualHost that will work with ProxyTunnel? I've tried various combinations of proxytunnel's -e, -E, and -X flags without any luck. The only lead I've found is Apache Bug No. 29744, but I haven't been able to find a patch that will install cleanly on Ubuntu Jaunty's Apache version 2.2.11-2ubuntu2.6. Thanks in advance.

  Read the article

• Why can't I connect to remote Microsoft SQL Server through SSH tunnel?

  - by Alexander

  I have at home a D-Link DIR-615 C1 router with DD-WRT. I set up the SSH server on the router, and log on through an SSH2-RSA passphrase-protected key. That router is the gateway between the local network and the internet. One of the computers on that network has Microsoft SQL Server 2008 installed, with TCP/IP protocol enabled through port 1433. I've set up port forwarding on the router, so that remote connections are possible and are, in fact, working (some developers log on remotely without problems). I am part of another network, that has internet access through a proxy server, which only has ports 80 and 443 opened. I can't connect to that MSSQL server on that remote server because 1433 port is closed on this network. I connected (using Putty) through 443 port to my router's SSH server, and set up 2 tunnels. One is for RDP (3389), and it's working. The other is for 1433 port, to connect to the server. I can't connect through the SSH tunnel to the MS SQL Server, neither through telnet, or through GUI clients. Am I missing something? Additional details: on connect, I get this error from SQL Server Management Studio: TITLE: Connect to Server Cannot connect to localhost:14330. ADDITIONAL INFORMATION: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server) (Microsoft SQL Server, Error: 3) For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&EvtSrc=MSSQLServer&EvtID=3&LinkId=20476 BUTTONS: OK The tunnel is configured like this: L14330 192.168.0.103:1433 192.168.0.103 is the permanent address of the SQL Server on the LAN. I also successfully forwarded TCP traffic of 3389 port to that IP, so tunneling is working to that IP address. When connecting without tunnel, through Microsoft SQL Server Management Studio, using the same method the connection establishes. Too bad my proxy doesn't allow 1433 port traffic, I wouldn't have this headache.

  Read the article

• Looking for a reliable Personal VPN Service

  - by user38673

  I am looking for a reliable personal VPN service so that I can access sites like Pandora or Hulu even when I am not physically in the US. I have been using StrongVPN but their service is not reliable. Here are some of my key requirements: Fast Reliable I don't mind paying a reasonable fee Unlimited traffic I just need PPTP support US IP addresses No software installation needed Supports Mac Any recommendations? Thanks.

  Read the article

• Reputable web based ssh client?

  - by Doug T.

  I'm sitting at a coffee shop right now, and I suspected I'd be able to ssh somewhere. Unlucky me they seem to be blocking everything but web traffic. I googled "web based ssh clients" however I have reservations about entering my login credentials on any Joe Schmoe's web app. I was wondering if anyone has had any experience with any reputable web based ssh clients? If so could you please point me at one that I could trust?

  Read the article

• Avoid blocked URL's when on VPN from home

  - by Marcus

  When I'm on my home PC and on my company VPN I can't get to sites that my company blocks. Is there a way to get around this? Why do my requests to facebook.com go through the VPN? Can you configure your system to, for instance, not go through the VPN for HTTP traffic?

  Read the article

• apache log analysis tools for multiple virtual hosts?

  - by shreddd

  I am interested in trying to get a side by side usage comparison of all the virtual hosts being served up by my apache server. In the simplest case, I want to see a list (or bar chart) with each virtual host and the number of requests/traffic on that site. I've been playing around with webalyzer and awstats but I haven't been able to compare multiple virtual hosts in the same infographic. Anyone have any suggestions on tools for doing this (or how I might use the above tools to do so)?

  Read the article

• SSH tunneling hangs with many connections

  - by middleofdreams

  I am forced to use SSH tunneling to access many servers (over 100) via one gateway server. To keep connection alive I am using autossh. Everything works pretty well until there is high traffic (people are connecting to most of the servers at once). then ssh process reaches 12% of cpu (which is configured maximum for separate process) and no connection is working anymore - i have to restart autossh script. What could be the possible reason for that?

  Read the article

• Can Azure host ColdFusion?

  - by mbursill

  A friend has a site developed in ColdFusion with MySQL and is looking for better cost-effective hosting as the traffic scales up rapidly. Azure comes to mind. I haven't used Azure myself, however, I believe it is possible to setup and interact with the web-server via RDP into a hosted Virtual Machine? I am curious if ColdFusion can be installed in the hosted Azure VM. Also, would the site have to be tweaked to run on Azure SQL, or could it continue to use MySQL? Thanks.

  Read the article

• Transient network dropout for Xen DomU's

  - by Stephen C

  We've got a CentOS server running a cluster of virtuals. Occasionally the cluster's internal network drops out for a minute or so ... and then comes back. The problem is somehow related to the actual network traffic, but it is not a simple load issue. (The system is generally lightly loaded, and the problem occurs irrespective of actual load.) The setup: CentOS 5.6 on Dom0, various CentOS on the DomU's Hardware - a Dell R710 with a BroadCom NextXpress 2 NIC (sigh) using the latest drivers for the NIC from BroadCom Xen configured to use network-bridge and vif-bridge Some iptable tweaks to route an unrelated port to one of the virtuals. The system has one externally visible IP address, and Dom0 runs an Apache httpd configured with a number of virtual hosts each of which reverse proxies to web servers running on the virtuals. (The virtuals have to be NAT'ed, primarily because we don't have enough allocated public IP addresses.) The symptoms: Works fine most of the time. When someone tries to UPLOAD a large file to one virtuals, the internal network drops out ... for all virtuals: The Dom0 httpd sees a network timeout talking to the backend server on the virtual and reports a 502. A previously established ssh connection from Dom0 to any of the DomU's freezes. Our monitoring shows ping failures for traffic between virtuals. The Xen consoles to the DomU's do not freeze. No log messages in any log files that I can see, on either Dom0 or the DomU's ... apart from the Dom0 httpd logs. After a minute or so, the problem clears by itself. This is 100% reproducible. What we've tried: Downloading, building and installing the latest BNX2 driver on Dom0 Turning off MSI on the NIC - adding "options bnx2 disable_msi=1" to /etc/modprobe.conf Turning off tcp segmentation offload - "ethtool -K eth0 tso off". Sacrificing a black rooster at midnight. I've exhausted all my options apart from switching to KVM ... or slaughtering more roosters. Any suggestions?

  Read the article

< Previous Page | 105 106 107 108 109 110 111 112 113 114 115 116  | Next Page >