Search Results

Search found 586 results on 24 pages for '802 11n'.

Page 11/24 | < Previous Page | 7 8 9 10 11 12 13 14 15 16 17 18  | Next Page >

• Wireless card disappeards when restart ubuntu

  - by Kristian Jones

  I used 'additional drivers' to install 'Broadcom STA wireless driver' and it returns an error. WIthin jockey.log it says the following numerous times. 2011-02-14 21:24:06,945 DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: blacklisted, b43legacy: blacklisted After it returns the error the network card will work temporarily until I restart the laptop. When I restart I got to go through the procedure again of trying to activate the driver, returns an error however it works temporarily. The network card is as follows on a Dell Inspiron 1545: Broadcom Corporation BCM4312 802.11b/g LP-PHY [14e4:4315] Rev 01 I have been trying to solve this myself for many hours. Any help is appreciated/

  Read the article

• Two Wifi Icons in Panel [Solved]

  - by Alex

  I have the exact problem in 13.10 as this user Two Wifi indicators in panel. Here are some screenshots: Here are some screenshots from another user: http://ubuntuforums.org/showthread.php?t=2183020&p=12825563 ifconfig and iwconfig outputs $ ifconfig lo Link encap:Local Loopback inet addr:XXXXXX Mask:XXXXXXX inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:2243 errors:0 dropped:0 overruns:0 frame:0 TX packets:2243 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:209889 (209.8 KB) TX bytes:209889 (209.8 KB) wlan0 Link encap:Ethernet HWaddr XXXXXXXXX inet addr:XXXXXX Bcast:XXXXXXXX Mask:XXXXXXX inet6 addr: XXXXXXX Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5925 errors:0 dropped:0 overruns:0 frame:0 TX packets:3361 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2951818 (2.9 MB) TX bytes:630579 (630.5 KB) $ iwconfig lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"XXXXX" Mode:Managed Frequency:2.437 GHz Access Point: XXXXXXXX Bit Rate=72.2 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on Link Quality=49/70 Signal level=-61 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:153 Invalid misc:472 Missed beacon:0

  Read the article

• Atheros AR8132 Ethernet refuses to connect after suspend

  - by Ramesh Patel

  I'm having an issue where my ethernet card (Atheros Communications Inc. AR8132 Fast Ethernet (rev c0)) refuses to recognize when a network cable is plugged in after a suspend. This is dmesg after suspending: [135897.712049] atl1c 0000:02:00.0: MAC state machine can't be idle since disabled for 10ms second [135897.743729] ADDRCONF(NETDEV_UP): eth0: link is not ready [135898.541804] ADDRCONF(NETDEV_UP): eth1: link is not ready [135900.452077] atl1c 0000:02:00.0: irq 47 for MSI/MSI-X [135900.672262] atl1c 0000:02:00.0: Error get phy ID [135900.673060] ADDRCONF(NETDEV_UP): eth0: link is not ready [135900.674140] ADDRCONF(NETDEV_UP): eth0: link is not ready [135925.604052] [135935.776051] eth1: no IPv6 routers present eth0 is the ethernet card and eth1 is the wlan card (Broadcom Corporation BCM43224 802.11a/b/g/n (rev 01)). The ethernet card uses the atl1c driver and the wlan card uses the wl driver. Sorry, should have mentioned as well, running Ubuntu 12.04 with kernel 3.2.0-25-generic.

  Read the article

• WiFi not working in Ubuntu 13.10 with Ralink RT3290

  - by Francisco

  I have upgraded from Ubuntu 13.04 to Ubuntu 13.10 and now my WiFi doesn't work. It takes a lot of time to connect but when connected, connection is quickly lost again. In Ubuntu 13.04 worked fine. Here are some outputs: lspci | grep Wireless 01:00.0 Network controller: Ralink corp. RT3290 Wireless 802.11n 1T/1R PCIe sudo rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no lsmod | grep rt2800 rt2800pci 18966 0 rt2800lib 95449 1 rt2800pci rt2x00pci 13287 1 rt2800pci rt2x00mmio 13661 1 rt2800pci rt2x00lib 56053 4 rt2x00pci,rt2800lib,rt2800pci,rt2x00mmio mac80211 634661 3 rt2x00lib,rt2x00pci,rt2800lib eeprom_93cx6 13344 1 rt2800pci crc_ccitt 12707 1 rt2800lib dmesg | grep rt2800 [ 19.959959] rt2800pci 0000:01:00.0: irq 46 for MSI/MSI-X modinfo rt2800pci | grep 3290 alias: pci:v00001814d00003290sv*sd*bc*sc*i*

  Read the article

• Help making TP-Link Wireless USB Adapter TL-WN723N work consistently

  - by Savvas Katseas

  I've only recently made the jump to Ubuntu, using 11.10/64 as my only desktop OS. Everything seems to be working fine, except my USB Wireless adapter, TP-Link's TL-WN723N which is randomly connecting and disconnecting. The connection time appears to be random, too: I've experienced hours of connectivity and lots of connections/disconnections. I've tried searching for a solution, but what I find doesn't concern this specific USB adapter. I'd like some help identifying the problem... I've also recently switched to using a D-Link router as a wireless hub, which creates its own wireless/n network. Unfortunately this didn't solve my problems, as the new n network can be joined, but there's no connectivity to the internet. I know that's not much info to help others solve my problem, so please let me know of what else I can provide to make this a better question -- and possibly help others facing similar trouble. lsusb reports that I'm using Realtek Semiconductor Corp. RTL8188SU 802.11n WLAN Adapter

  Read the article

• Cannot connect to secure wireless with Netgear wna3100 USB

  - by Vince Radice

  I have installed Ubuntu 11.10. I used a wired connection to download and install all of the updates. When I tried to use a Netgear WNA3100 wireless USB network adapter, it failed. Much searching and trying things I was finally able to get it working by disabling security on my router. I have verified this by disabling security and I was able to connect. When I enabled security (WPA2 PSK), the connection failed. What is necessary to enable security (WPA2 PSK) and still use the Netgear USB interface? Here is the output from the commands most requested lsusb Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 003: ID 0846:9020 NetGear, Inc. WNA3100(v1) Wireless-N 300 [Broadcom BCM43231] lshw -C network *-network description: Ethernet interface product: RTL-8139/8139C/8139C+ vendor: Realtek Semiconductor Co., Ltd. physical id: 3 bus info: pci@0000:02:03.0 logical name: eth0 version: 10 serial: 00:40:ca:44:e6:3e size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=half latency=32 link=no maxlatency=64 mingnt=32 multicast=yes port=MII speed=10Mbit/s resources: irq:19 ioport:c800(size=256) memory:ee011000-ee0110ff memory:40000000-4000ffff *-network description: Wireless interface physical id: 1 logical name: wlan0 serial: e0:91:f5:56:e1:0d capabilities: ethernet physical wireless configuration: broadcast=yes driver=ndiswrapper+bcmn43xx32 driverversion=1.56+,08/26/2009, 5.10.79.30 ip=192.168.1.104 link=yes multicast=yes wireless=IEEE 802.11g iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11g ESSID:"vincecarolradice" Mode:Managed Frequency:2.422 GHz Access Point: A0:21:B7:9F:E5:EE Bit Rate=121.5 Mb/s Tx-Power:32 dBm RTS thr:2347 B Fragment thr:2346 B Encryption key:off Power Management:off Link Quality:76/100 Signal level:-47 dBm Noise level:-96 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 ndiswrapper -l bcmn43xx32 : driver installed device (0846:9020) present lsmod | grep ndis ndiswrapper 193669 0 dmesg | grep -e ndis -e wlan [ 907.466392] ndiswrapper version 1.56 loaded (smp=yes, preempt=no) [ 907.838507] ndiswrapper (import:233): unknown symbol: ntoskrnl.exe:'IoUnregisterPlugPlayNotification' [ 907.838955] ndiswrapper: driver bcmwlhigh5 (Netgear,11/05/2009, 5.60.180.11) loaded [ 908.137940] wlan0: ethernet device e0:91:f5:56:e1:0d using NDIS driver: bcmwlhigh5, version: 0x53cb40b, NDIS version: 0x501, vendor: 'NDIS Network Adapter', 0846:9020.F.conf [ 908.141879] wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK [ 908.143048] usbcore: registered new interface driver ndiswrapper [ 908.178826] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 994.015088] usbcore: deregistering interface driver ndiswrapper [ 994.028892] ndiswrapper: device wlan0 removed [ 994.080558] ndiswrapper version 1.56 loaded (smp=yes, preempt=no) [ 994.374929] ndiswrapper: driver bcmn43xx32 (,08/26/2009, 5.10.79.30) loaded [ 994.404366] ndiswrapper (mp_init:219): couldn't initialize device: C0000001 [ 994.404384] ndiswrapper (pnp_start_device:435): Windows driver couldn't initialize the device (C0000001) [ 994.404666] ndiswrapper (mp_halt:262): device e05b6480 is not initialized - not halting [ 994.404671] ndiswrapper: device eth%d removed [ 994.404709] ndiswrapper: probe of 1-5:1.0 failed with error -22 [ 994.406318] usbcore: registered new interface driver ndiswrapper [ 2302.058692] wlan0: ethernet device e0:91:f5:56:e1:0d using NDIS driver: bcmn43xx32, version: 0x50a4f1e, NDIS version: 0x501, vendor: 'NDIS Network Adapter', 0846:9020.F.conf [ 2302.060882] wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK [ 2302.113838] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 2354.611318] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 2355.268902] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 2365.400023] wlan0: no IPv6 routers present [ 2779.226096] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 2779.422343] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 2797.574474] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 2802.607937] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 2803.261315] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 2813.952028] wlan0: no IPv6 routers present [ 3135.738431] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3139.180963] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3139.816561] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.229872] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.444542] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.758297] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3163.860684] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3205.118732] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3205.139553] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3205.300542] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3353.341402] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3363.266399] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3363.505475] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3363.506619] ndiswrapper (set_iw_auth_mode:601): setting auth mode to 5 failed (00010003) [ 3363.717203] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3363.779206] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3405.206152] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3405.248624] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3405.577664] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3438.852457] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3438.908573] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.282995] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.325237] ndiswrapper (set_iw_auth_mode:601): setting auth mode to 5 failed (00010003) [ 3568.460716] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.461763] ndiswrapper (set_iw_auth_mode:601): setting auth mode to 5 failed (00010003) [ 3568.809776] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3568.880641] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3610.122848] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3610.148328] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3610.324502] ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 3636.088798] ndiswrapper (iw_set_auth:1602): invalid cmd 12 [ 3636.712186] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 3647.600040] wlan0: no IPv6 routers present I am using the system now with the router security turned off. When I submit this, I will turn security back on.

  Read the article

• How to improve wireless network speed?

  - by Toby

  I am running 10.04 LTS on a desktop PC with a Belkin G-Plus MIMO Wireless network card. Ever since running Ubuntu on the machine I have noticed fairly slow network speeds (about half the speed I get when running the same card through Windows) I did some research I found out that by and large wireless network cards aren't that well supported on most Linux distros. I was wondering though if there is anything I could be tweaking on the system that could help squeeze a little more out of the card? Here is some more information *-network:1 description: Wireless interface physical id: 2 logical name: wlan0 serial: 00:1c:df:24:5e:54 capabilities: ethernet physical wireless configuration: broadcast=yes ip=192.168.1.5 multicast=yes wireless=IEEE 802.11bg

  Read the article

• Replace Broadcom "wl" driver with "b43"

  - by Laszlo Boros

  I'm using Ubuntu 10.04.4 LTS, and in my laptop there is a Broadcom BCM4312 wlan card. lspci output: 04:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g (rev 01) Subsystem: Broadcom Corporation Device 04b5 Flags: bus master, fast devsel, latency 0, IRQ 18 Memory at f4500000 (64-bit, non-prefetchable) [size=16K] Capabilities: [40] Power Management version 3 Capabilities: [58] Vendor Specific Information Capabilities: [e8] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable- Capabilities: [d0] Express Endpoint, MSI 00 Capabilities: [100] Advanced Error Reporting Capabilities: [13c] Virtual Channel Capabilities: [160] Device Serial Number 81-ac-1d-ff-ff-12-54-92 Capabilities: [16c] Power Budgeting Kernel driver in use: wl Kernel modules: wl, ssb So as you can see, the current (and default) driver is wl - installed with jockey. But I have another Ubuntu based distribution on my laptop (BackTrack linux), which is also 10.04, but it has the b43 driver installed and the overall performance is MUCH better. So I would like to install it on this OS too, but even google didn't help me. So my question is how to install the latest b43 driver on my Ubuntu?

  Read the article

• Can't find ALL wireless networks, just my neighbours

  - by motoringeek

  Been playing with live discs since 10.10 but now have gone ahead and dual booted. I have a Acer 5742z with a Nplify 802.11b/g/n wireless connection. The install went well and drivers seem to be working. BUT, although wireless detects some local networks it doesn't find mine. I have WPA-PSK security on my modem, could this be the problem?? I don't want to change my modem settings as all my other WIFI devices are contected to it. So I need help in finding my home network. A step by step guide would be useful. I am using Windows 7 now to write this but would love it if I could use Ubuntu online. I only can when I connect an Ethernet cable. Thanks in advance.

  Read the article

• Ubuntu 10.04, I cannot get my computer to connect to the internet

  - by Jared Isaacson

  So at first I was unable to get my Belkin Surf & Share usb to install on my computer, so then I plugged my computer directly into my router and my computer won't acknowledge any connection. I know very little about how to use ubuntu, please help me. What I do know is: I'm using Ubuntu 10.04 Lucid Lynx In my 'edit connections', I go into 'wired' tab, select "wired connection 1" then 'edit' it brings up 4 tab options: Wired (I input the MAC address that's printed on the bottom of my router, MTU is set to automatic) 802.1x Security (currently: not checked) IPv4 Settings (currently: Automatic (DHCP) addresses only) IPv6 Settings (currently: Automatic)

  Read the article

• Broadcom wireless card disappeards on restart

  - by Kristian Jones

  I used 'additional drivers' to install 'Broadcom STA wireless driver' and it returns an error. WIthin jockey.log it says the following numerous times. 2011-02-14 21:24:06,945 DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: blacklisted, b43legacy: blacklisted After it returns the error the network card will work temporarily until I restart the laptop. When I restart I got to go through the procedure again of trying to activate the driver, returns an error however it works temporarily. The network card is as follows on a Dell Inspiron 1545: Broadcom Corporation BCM4312 802.11b/g LP-PHY [14e4:4315] Rev 01 I have been trying to solve this myself for many hours. Any help is appreciated/

  Read the article

• JavaOne - Java SE Embedded Booth - Digi - Home Health Hub (HHH)

  - by David Clack

  Hi All,  So another exciting platform we will have in the booth at JavaOne is the Digi  Home Health Hub (HHH) platform. http://www.digi.com/products/wireless-wired-embedded-solutions/single-board-computers/idigi-telehealth-application-kit#overview This is a Freescale reference design that has been built by Digi, the system is powered by a Freescale i.MX28 ARM SOC, what's really exciting me is it has every wireless protocol you could ever want on a single motherboard. Ethernet, 802.11b/g/n Wi-Fi, Bluetooth, ZigBee, configurable Sub-GHz radio, NFC plus USB, audio and LCD/touch screen option. I've been experimenting with lots of wireless capable healthcare products in the last few months, plus some Bluetooth Pulse / Oxy meters, we have been looking at how the actual healthcare wireless protocols work. Steve Popovich - Vice President, Digi Internationalwill be doing a talk at the Java Embedded @ JavaOne conference in the Hotel Nikko, right next door to the JavaOne show in the Hilton. If you are registered at JavaOne you can come over to the Java Embedded @ JavaOne for $100 Come see us in booth 5605 See you there Dave

  Read the article

• Ubuntu 12.10 64bit fresh install, wireless issue!

  - by Dave

  Just installed a fresh Ubuntu 12.10 64bit on my laptop, run the update manager, restarted and suddenly I can't use my wifi anymore. Ubuntu software center installed automatically the wifi additional driver as you can see in my screenshot. If I mark the option "Do not use the device" and apply changes, restarting Ubuntu my wifi is back and I can use it. If I run iwconfig my terminal is showing this Now if I use Ubuntu for more than 20 minutes surfing the web my wifi it keeps to be connected but I don't receive any signal from it. Any page I try to open it simply don't open (just waiting icon). If I disconnect my wifi and connect it again, same issue, it doesn't work. The only way to make it work again is to restart Ubuntu. And the same story it happens again after aprox. 20, 30 minutes. WIFI device details: 03:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01) Thanks, Dave

  Read the article

• How to prevent WLAN connection from dropping permanently on a Fritz USB WLAN N stick?

  - by Chris

  I have a desktop with a Fritz USB WLAN N stick and tried Ubuntu 12.04. Installation went fine and WLAN is working. However, connection drops permanent. Reconnecting manually fixes it but after a few minutes it drops again. It's connected to a Vodafone 802 box with WLAN N fix set. It seems that it works when I switch off N mode. But I need to test. Can someone confirm this issue or is there another solution? I have another machine with 12.04 (HP 625 laptop) running where connection is stable.

  Read the article

• Steps to diagnose SNU5600 disconnection problem

  - by Rich

  I have a Philips SNU5600 WiFi dongle plugged into two machines (ie I have two SNU5600 dongles, one in each machine). One machine is running 10.10 and the other is running Linux Mint. The dongles work absolutely fine, except if I do a lot of file transfers to a NAS attached to the wireless router. After a while the connection to the router will go. To get the connection back I either need to run sudo /etc/init.d/networking restart or I need to unplug and plug in again the dongle. Otherwise the dongle works fine (web browsing, streaming, etc). Output of lsusb: Bus 002 Device 003: ID 0471:1236 Philips (or NXP) SNU5600 802.11bg Output of lsusb -v at http://pastebin.com/dXYKkF01 What steps should I take next to resolve this? Is it a known problem? Could it be the router? It is a 3Com "OfficeConnect Wireless 11g Cable/DSL Gateway Version 1.02.15".

  Read the article

• Can't connect to WIFI after sleep Ubuntu 14.04

  - by user3380404

  After an upgrade over a previous version to Ubuntu 14.04 I have problems with connecting to WiFi. After suspending it won't reconnect to any existing network unless I restart the laptop. sudo lshw -C network: *-network description: Ethernet interface product: 82567LM Gigabit Network Connection vendor: Intel Corporation physical id: 19 bus info: pci@0000:00:19.0 logical name: eth0 version: 03 serial: 00:27:13:b4:d3:58 capacity: 1Gbit/s width: 32 bits clock: 33MHz capabilities: pm msi bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=e1000e driverversion=2.3.2-k firmware=1.8-3 latency=0 link=no multicast=yes port=twisted pair resources: irq:45 memory:fc200000-fc21ffff memory:fc225000-fc225fff ioport:1840(size=32) *-network description: Wireless interface product: PRO/Wireless 5100 AGN [Shiloh] Network Connection vendor: Intel Corporation physical id: 0 bus info: pci@0000:03:00.0 logical name: wlan0 version: 00 serial: 00:26:c6:c6:6b:c8 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.13.0-29-generic firmware=8.83.5.1 build 33692 ip=10.0.1.160 latency=0 link=yes multicast=yes wireless=IEEE 802.11abgn resources: irq:48 memory:f4200000-f4201fff

  Read the article

• Wi-fi interface fails to authenticate on secured networks

  - by Eduardo Bezerra

  the problem is that I can't connect to wireless networks that have security enabled. I can connect fine to the unsecured network of my university, but not to the secured one in the same building. Also, it fails to connect to my home wireless router, which uses wpa2 encryption. Any ideas? I have a Broadcom Corporation BCM43224 802.11a/b/g/n (rev 01), with pci id [14e4:4353], running Ubuntu 12.10 on a macbook pro 6,2. I'm using bcmwl-kernel-source package with kernel module wl to enable my wi-fi device.

  Read the article

• Can't connect to wireless on Lubuntu

  - by migwke

  I have a CISCO 802.11b WIFI Mini PCI LAN card in my IBM ThinkPad T30 laptop. Is this wireless card compatible with Lubuntu? I have Lubuntu installed and it just won't connect. It keeps saying that it is trying to configure then it says that it is connected but it does not work. I know that the wireless network is working correctly because I can connect to it with all my other devices and it works on this very same laptop when I am running Windows. I added the following commands to blacklist.conf, but still no luck blacklist padlock_aes blacklist geode_aes

  Read the article

• Asus X552VL WI-FI Problem

  - by Mitkobg

  I have a problem with my Wireless on my laptop. When i did rfkill list: 1: asus-wlan: Wireless LAN Soft blocked: no Hard blocked: no 2: asus-bluetooth: Bluetooth Soft blocked: no Hard blocked: no 4: hci0: Bluetooth Soft blocked: no Hard blocked: no 5: phy1: Wireless LAN Soft blocked: no Hard blocked: yes itko@Mitko:~$ iwconfig eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off mitko@Mitko:~$ lspci -nnk | grep -A2 0280 03:00.0 Network controller [0280]: Qualcomm Atheros AR9485 Wireless Network Adapter [168c:0032] (rev 01) Subsystem: AzureWave Device [1a3b:2c97] Kernel driver in use: ath9k mitko@Mitko:~$ lsmod | grep -e ath9k -e asus asus_nb_wmi 16990 0 asus_wmi 24191 1 asus_nb_wmi sparse_keymap 13948 1 asus_wmi ath9k 164164 0 ath9k_common 13551 1 ath9k ath9k_hw 453856 2 ath9k_common,ath9k ath 28698 3 ath9k_common,ath9k,ath9k_hw mac80211 626557 1 ath9k cfg80211 484040 4 wl,ath,ath9k,mac80211 wmi 19177 3 mxm_wmi,nouveau,asus_wmi video 19476 3 i915,nouveau,asus_wmi

  Read the article

• Wlan connection got lost permanent

  - by chris

  I have a desktop with a fritz usb wlan n tick and tried ubuntu 12.04. installlation is fine and wlan is working, however connection drops permanent. reconnecting manually fixes it but after a few minutes it drops again. it's connected to a vodafone 802 box with wlan n fix set. it seems that it works when i switch off n mode...but i need to test. can someone confirm or is there another solution? i have another machine with 12.04 (hp 625 laptop) running where connection is stable. any help much appreciated. thank chris

  Read the article

• Ubuntu 12.04, can't find my home wifi network

  - by Anton

  I've tried several solutions I found on the web, but didn't manage to solve a problem. Since today my laptop won't find my WiFi network, but neighbours' networks are suggested. Another laptop with U12.04 does find one. What do I do? I've Dell Latitude-E4310, 02:00.0 Network controller: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter (rev 01) Subsystem: Dell Inspiron M5010 / XPS 8300 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f2c00000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: brcmsmac Kernel modules: bcma, brcmsmac also NetworkManager Tool State: connected (global) - Device: eth1 ----------------------------------------------------------------- Type: 802.11 WiFi Driver: wl State: disconnected Default: no HW Address: 1C:65:9D:7A:45:5C Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Should I provide anything else? Many thanks in advance.

  Read the article

• Intel Centrino Wireless-N 1000 Again ! Ubuntu 13.04 x64

  - by vafa

  First I have to say that I tried everything written about this concept. The problem is that it stops working randomly in 3 main forms : 1 - sometimes it disconnect from wireless network and reconnect automatically 2 - sometimes it disconnect and wont connect no matter what (needs reboot) 3 - some times it's still connected but cannot ping or surf or whatever. I already tried disabling N mod using these commands : sudo modprobe -r iwlwifi modprobe iwlwifi 11n_disable=1 (or 0, whatever) it didn't help . these are the results of lspci, sudo lshw -C network, ifconfig, iwconfig, rfkill list when it disconnected and didn't connect till reboot : ifconfig : eth0 Link encap:Ethernet HWaddr c8:0a:a9:34:65:77 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:1563213476557380 errors:9379306629148050 dropped:3126435543049350 overruns:1563217771524675 frame:7816088857623375 TX packets:1563217771524675 errors:6252871086098700 dropped:0 overruns:1563217771524675 carrier:3126435543049350 collisions:7816088857623375 txqueuelen:1000 RX bytes:1563217771524675 (1.5 PB) TX bytes:1563217771524675 (1.5 PB) ham0 Link encap:Ethernet HWaddr 7a:79:19:a5:e4:93 inet addr:25.165.228.147 Bcast:25.255.255.255 Mask:255.0.0.0 inet6 addr: fe80::7879:19ff:fea5:e493/64 Scope:Link inet6 addr: 2620:9b::19a5:e493/96 Scope:Global UP BROADCAST RUNNING MULTICAST MTU:1404 Metric:1 RX packets:7743 errors:0 dropped:0 overruns:0 frame:0 TX packets:1250 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:665642 (665.6 KB) TX bytes:204056 (204.0 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:41138 errors:0 dropped:0 overruns:0 frame:0 TX packets:41138 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:6420962 (6.4 MB) TX bytes:6420962 (6.4 MB) wlan0 Link encap:Ethernet HWaddr 00:1e:64:45:fb:70 inet6 addr: fe80::21e:64ff:fe45:fb70/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:286999 errors:0 dropped:0 overruns:0 frame:0 TX packets:226966 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:324386887 (324.3 MB) TX bytes:30674804 (30.6 MB) iwconfig : ham0 no wireless extensions. eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=14 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off sudo lshw -C network: *-network description: Wireless interface product: Centrino Wireless-N 1000 [Condor Peak] vendor: Intel Corporation physical id: 0 bus info: pci@0000:07:00.0 logical name: wlan0 version: 00 serial: 00:1e:64:45:fb:70 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlwifi driverversion=3.8.0-30-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bg resources: irq:46 memory:c0400000-c0401fff *-network description: Ethernet interface product: AR8131 Gigabit Ethernet vendor: Qualcomm Atheros physical id: 0 bus info: pci@0000:09:00.0 logical name: eth0 version: c0 serial: c8:0a:a9:34:65:77 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=atl1c driverversion=1.0.1.1-NAPI latency=0 link=no multicast=yes port=twisted pair resources: irq:47 memory:c0900000-c093ffff ioport:5000(size=128) *-network description: Ethernet interface physical id: 2 logical name: ham0 serial: 7a:79:19:a5:e4:93 size: 10Mbit/s capabilities: ethernet physical configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full ip=25.165.228.147 link=yes multicast=yes port=twisted pair speed=10Mbit/s lspci: 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port (rev 07) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.3 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 4 (rev 03) 00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 6 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.3 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 01:00.0 VGA compatible controller: NVIDIA Corporation G98M [GeForce G 105M] (rev a1) 07:00.0 Network controller: Intel Corporation Centrino Wireless-N 1000 [Condor Peak] 09:00.0 Ethernet controller: Qualcomm Atheros AR8131 Gigabit Ethernet (rev c0) rfkill list : 1: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no 2: acer-bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 9: phy0: Wireless LAN Soft blocked: no Hard blocked: no any help will be REALLLYYYY appreciated

  Read the article

• Connection manager detects network but won't connect

  - by Carson Chittom

  I've just installed 12.04 on my home desktop. Because of where it's located, in order not to have my children tripping over cat5 cable, I've got a cheap 802.11n USB device plugged in, which uses a Realtek 8192CU chip. The house wifi is protected with WPA2. Ubuntu's Network Manager detects the network, but connecting to it just times out and asks for the password again. I'm sure I'm using the correct password. No other computers on the house network are having any difficulty. This device previously worked correctly with both Windows 7 and OpenBSD in the same machine. The linux-firmware package is installed (from the disc) at version 1.79, and /lib/firmware/rtlwifi/rtl8192cufw.bin is present. dmesg|grep rtl only shows the "loading firmware" message. I've tried Google, but I apparently can't find the right set of words to plug in, because I haven't found anything related (lots of "doesn't work at all," but nothing matching my circumstances). Any help would be greatly appreciated.

  Read the article

• Which version of ubuntu is compatible with ACER Aspire 5732Z?

  - by Mehdi Bateni

  I have an ACER Aspire 5732Z Laptop, and 6 days ago I have installed Ubuntu 11.10 on my laptop, But I found black screen in login. I have tried a lot of ways to solve this problem, but there is no way. So can you tell me which version is compatible with this ACER Aspire (5732Z)? Detail: Intel-Pentium-processor T4400 (2.2 GHz, 800 MHz FSB), Intel-GMA 4500M, 15.6" HD LCD, 2GB Memory, 320 GB HDD, Acer Nplify(TM) 802.11b/g/n. Thank You. .. And finally, I found that Linux Mint is best for my ACER-ASPIRE5732Z. It is also compatible with Ubuntu codes, because as I know it is base on Ubuntu.

  Read the article

• slow speed transfering files to a local network device

  - by F. Ariel Jung

  I'm having troubles copying files from my pc(ubuntu 13.04 64 bits) to a Media Center(WDTV Live: with an SATA2 HDD attached) through the local network. the speed is to slow, it's up to 2.0 MB/s image: http://s11.postimg.org/g1nuai92b/Captura_de_pantalla_de_2013_06_24_07_46_55.png (I don't use image tag because it is a big image) my PC has a wifi network card Tp Link TL-WN951N and it is connected to a TP Link TL-WDR3500 router via wifi, and the WDTV Live is connected via LAN here is a iwconfig: eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"TL-WDR3500" Mode:Managed Frequency:2.462 GHz Access Point: A0:F3:C1:6C:3B:F1 Bit Rate=39 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=62/70 Signal level=-48 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:33521 Invalid misc:2245290 Missed beacon:0 if more data is required I'll post it as needed. I can't figure this out, needed help. please

  Read the article

< Previous Page | 7 8 9 10 11 12 13 14 15 16 17 18  | Next Page >