Search Results

Search found 586 results on 24 pages for '802 11n'.

Page 9/24 | < Previous Page | 5 6 7 8 9 10 11 12 13 14 15 16  | Next Page >

• iwconfig, iw not displaying wireless information

  - by Srivatsa Kanchi

  after fresh install to 12.10, the wireless information is not shown by both iwconfig and iw. The wireless sets up successfully and able to connect This is what i get $ iwconfig wlan0 wlan0 IEEE 802.11abgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=14 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off $ iw wlan0 link Not connected. $ uname -a Linux srivatsa-ThinkPad-T61 3.5.0-18-generic #29-Ubuntu SMP Fri Oct 19 10:26:51 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux

  Read the article

• Wireless Lan driver for Toshiba Satellite C850-A823 PSKCCV-02300XAR

  - by user111942

  I have Toshiba Satellite C850-A823 PSKCCV-02300XAR Laptop, i had installed Ubuntu 12.10 as dual boot (windows 7 already working), after the installation i had noticed that wireless driver not installed in ubuntu 12.10, from windows device manager i got details of wireless lan driver as follows "Realtek RTL8723AE Wireless LAN 802.11n PCI-E NIC" i dont have LAN cable connection, kindly help me how to get wireless driver and install in ubuntu 12.10 hoping for your kind support shiyas

  Read the article

• Why wifi doesn't work in this case?

  - by xRobot

  I have a brand new notebook where I have installed Windows 7 and Ubuntu 12.04 LTS 64bit in dual boot. In windows 7 wifi works but in Ubuntu not. Could you help me please ? iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off eth0 no wireless extensions. lshw -C network *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 07 serial: b4:b5:1f:1b:9a:56 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl8168e-3_0.0.4 03/27/12 latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:41 ioport:3000(size=256) memory:c2404000-c2404fff memory:c2400000-c2403fff *-network description: Wireless interface product: Ralink corp. vendor: Ralink corp. physical id: 0 bus info: pci@0000:02:00.0 logical name: wlan0 version: 00 serial: 84:4b:f4:0a:3a:22 width: 32 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=rt2800pci driverversion=3.2.0-31-generic firmware=0.34 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:c2500000-c250ffff lspci | grep -i net 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 07) 02:00.0 Network controller: Ralink corp. Device 539a iwlist scan lo Interface doesn't support scanning. wlan0 Interface doesn't support scanning : Device or resource busy eth0 Interface doesn't support scanning. lsmod Module Size Used by rfcomm 47604 0 bnep 18281 2 bluetooth 180104 10 rfcomm,bnep parport_pc 32866 0 ppdev 17113 0 snd_hda_codec_hdmi 32474 1 snd_hda_codec_realtek 224173 1 joydev 17693 0 hp_wmi 18092 0 sparse_keymap 13890 1 hp_wmi snd_hda_intel 33773 3 snd_hda_codec 127706 3 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel snd_hwdep 13668 1 snd_hda_codec snd_pcm 97188 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec snd_seq_midi 13324 0 snd_rawmidi 30748 1 snd_seq_midi snd_seq_midi_event 14899 1 snd_seq_midi snd_seq 61896 2 snd_seq_midi,snd_seq_midi_event snd_timer 29990 2 snd_pcm,snd_seq snd_seq_device 14540 3 snd_seq_midi,snd_rawmidi,snd_seq psmouse 97362 0 snd 78855 16 snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_rawmidi,snd_seq,snd_timer,snd_seq_device arc4 12529 2 rt2800pci 18715 0 rt2800lib 58925 1 rt2800pci crc_ccitt 12667 1 rt2800lib rt2x00pci 14577 1 rt2800pci rt2x00lib 51144 3 rt2800pci,rt2800lib,rt2x00pci mac80211 506816 3 rt2800lib,rt2x00pci,rt2x00lib soundcore 15091 1 snd mac_hid 13253 0 uvcvideo 72627 0 videodev 98259 1 uvcvideo v4l2_compat_ioctl32 17128 1 videodev wmi 19256 1 hp_wmi i915 473240 3 cfg80211 205544 2 rt2x00lib,mac80211 eeprom_93cx6 12725 1 rt2800pci drm_kms_helper 46978 1 i915 drm 242038 4 i915,drm_kms_helper i2c_algo_bit 13423 1 i915 snd_page_alloc 18529 2 snd_hda_intel,snd_pcm mei 41616 0 serio_raw 13211 0 video 19596 1 i915 lp 17799 0 parport 46562 3 parport_pc,ppdev,lp usbhid 47199 0 hid 99559 1 usbhid r8169 62099 0 rfkill list: # rfkill list 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no 1: hp-wifi: Wireless LAN Soft blocked: no Hard blocked: no

  Read the article

• Dell Inspiron 15R 5520 Wireless Device Not Detected

  - by ashish

  I bought a Dell Inspiron 5520 15R last week and I am a newbie in Ubuntu platform. I installed Windows 7 as well as Ubuntu 12.04 64-bit. But my wireless device is not detected in Ubuntu while it is working fine in Windows OS. My wireless device is Dell Wireless 1704 802.11B 2.4GHZ. Is this a compatibility problem with Ubuntu. What would be the solution? Do I need to install another version of Ubuntu?

  Read the article

• Wifi problems after upgrading to 13.10

  - by Simon

  I just upgraded to Ubuntu 13.10, but since the upgrade I don't have internet access via wifi anymore. I can: See networks Connect to a network Ping myself (localhost, 192.168.0.103) I can't: Ping others (including other devices on the same wireless network, including the gateway/router) Resolve hosts Access any other external resource, whether on my own network or on the internet Using Wireshark, I noticed my computer is continuously sending ARP-requests like "Who has 192.168.0.1 [which is the gateway]? Tell 192.168.0.103". It doesn't get any replies though. When I ping another IP-address for which it knows the mac-address (from cache), it turns out a packet loss of 90% occurs, and even if a packet manages to arrive it takes around 3000ms. The output of route -n is: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth1 192.168.0.0 0.0.0.0 255.255.255.0 U 9 0 0 eth1 192.168.122.0 0.0.0.0 255.255.255.0 U 0 0 0 virbr0 Before upgrading, wifi worked fine. Using other devices, wifi still works fine.Resetting the router didn't help. Ethernet still works after upgrading. Any suggestions? Update: I'm using the wl driver. Here's the relevant output of some commands: lspci | grep Wireless 03:00.0 Network controller: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter (rev 01) cat /etc/modprobe.d/blacklist.conf [...] blacklist mac80211 blacklist brcm80211 blacklist cfg80211 blacklist lib80211_crypt_tkip blacklist lib80211 blacklist b43 cat /etc/rc.local sudo modprobe -r lib80211 sudo insmod /lib/modules/3.2.0-30-generic-pae/kernel/net/wireless/lib80211.ko sudo insmod /lib/modules/3.2.0-30-generic-pae/kernel/net/wireless/lib80211_crypt_wep.ko sudo insmod /lib/modules/3.2.0-30-generic-pae/kernel/net/wireless/lib80211_crypt_tkip.ko sudo insmod /lib/modules/3.2.0-30-generic-pae/kernel/net/wireless/lib80211_crypt_ccmp.ko sudo modprobe wl exit 0 The last lines are probably how I got wireless working after the previous upgrade (wireless has been a problem after each upgrade). Update 2: added information about the exact hardware below. The hardware is an integrated device, so I ran lspci -nn | grep -i network. The output is: 03:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter [14e4:4727] (rev 01)

  Read the article

• can not always shutdown when wireless connection on

  - by user67362

  When the wireless connection on, I can not always shutdown my computer, always it stoped at the ubuntu interface. But if I use "sudo ifconfig wlan0 down" before shutdown, it will not happen, is there something wrong with the wireless dirver? 03:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8188CE 802.11b/g/n WiFi Adapter (rev 01) 09:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03)

  Read the article

• No firmware found for b43 wireless controlloer (BCM4318) on a Dell Latitude D610

  - by Stanton.Sculpture

  Trying to get my 03:03.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02) working. I just reformated and installed 12.04 on this old Windows XP machine, and I don't know where to get the firmware for this. This is what I got when I typed sudo lshw -c network: http://pastebin.ubuntu.com/1041161/ Also, when I go to additional drivers in the system settings, no proprietary drivers show up. Any help I can get on this would be Great, Thanks!

  Read the article

• L'intelligence d'un réseau de voitures au service de la sécurité des automobilistes, le projet SIM devrait sauver des milliers de vies des accidents

  L'intelligence d'un réseau de voitures au service de la sécurité des automobilistes Le projet SIM devrait sauver des milliers de vies des accidents de circulationL'internet partout, celui-là même qui par définition permet d'interconnecter des objets (véhicules, hélicoptères et autres), processus et personnes, se dévoile peu à peu au grand public à travers des projets concrets à l'exemple de SIM (Safe Intelligent Mobility) de l'université des technologies du München "Technische Universität München".SIM permet de créer un réseau entre véhicules équipés de la technologie de même nom. Technologie qui d'après Cisco, devrait être compatible avec la norme sans fil 802.11p (une variante IEEE d'une norme...

  Read the article

• Wireless broken after latest 12.04 update

  - by inderpaldeol

  I updated 12.04 yesterday and it broke my wireless connection. iwconfig lo no wireless extensions. eth0 no wireless extensions. l@ubuntu:~$ lspci|grep Network 03:00.0 Network controller: Ralink corp. RT3090 Wireless 802.11n 1T/1R PCIe In the hardware drivers, I see - rt3090sta is activated but currently not in use. WICD does not show wireless networks. Can someone help me please? Thanks id

  Read the article

• bonding module parameters are not shown in /sys/module/bonding/parameters/

  - by c4f4t0r

  I have a server with Suse 11 sp1 kernel 2.6.32.54-0.3-default, with modinfo bonding i see all parameters, but under /sys/module/bonding/parameters/ not modinfo bonding | grep ^parm parm: max_bonds:Max number of bonded devices (int) parm: num_grat_arp:Number of gratuitous ARP packets to send on failover event (int) parm: num_unsol_na:Number of unsolicited IPv6 Neighbor Advertisements packets to send on failover event (int) parm: miimon:Link check interval in milliseconds (int) parm: updelay:Delay before considering link up, in milliseconds (int) parm: downdelay:Delay before considering link down, in milliseconds (int) parm: use_carrier:Use netif_carrier_ok (vs MII ioctls) in miimon; 0 for off, 1 for on (default) (int) parm: mode:Mode of operation : 0 for balance-rr, 1 for active-backup, 2 for balance-xor, 3 for broadcast, 4 for 802.3ad, 5 for balance-tlb, 6 for balance-alb (charp) parm: primary:Primary network device to use (charp) parm: lacp_rate:LACPDU tx rate to request from 802.3ad partner (slow/fast) (charp) parm: ad_select:803.ad aggregation selection logic: stable (0, default), bandwidth (1), count (2) (charp) parm: xmit_hash_policy:XOR hashing method: 0 for layer 2 (default), 1 for layer 3+4 (charp) parm: arp_interval:arp interval in milliseconds (int) parm: arp_ip_target:arp targets in n.n.n.n form (array of charp) parm: arp_validate:validate src/dst of ARP probes: none (default), active, backup or all (charp) parm: fail_over_mac:For active-backup, do not set all slaves to the same MAC. none (default), active or follow (charp) in /sys/module/bonding/parameters ls -l /sys/module/bonding/parameters/ total 0 -rw-r--r-- 1 root root 4096 2013-10-17 11:22 num_grat_arp -rw-r--r-- 1 root root 4096 2013-10-17 11:22 num_unsol_na I found some of this parameters under /sys/class/net/bond0/bonding/, but when i try to change one i got the following error echo layer2+3 > /sys/class/net/bond0/bonding/xmit_hash_policy -bash: echo: write error: Operation not permitted

  Read the article

• Looking for cheap Wireless router, with USB for attached USB disk drive

  - by geoffc

  I have a 802.11b router at home (DLink DI-614+ (B rev)) and it is working perfectly well for me. I want to replace it though, since it is out of updates, and now several years old and heck, I want a new toy to configure! I was trying to decide what to get. I could care less about 802.11g or n support, since B is fast enough, but every device in my house is now B/G, so G would be fine for me. N buys me little to nothing. (Small enough house that range is a non-issue). The features I realized I want are a USB port for sharing a USB hard drive. I would like to have a central device I could store files on. I do not want to waste the power of an always running PC to do this, so a router seems like the place to go. I would love it, if it could support Vonage VOIP as well, then I could ditch a power brick from a second device (I have the small DLink Vonage VOIP box). All the current examples of this router (with USB drive, yet to find one with VOIP too!) are in the $100+ range, and N and silly, when a B/G is in the $30 range around here.

  Read the article

• 1000Base-X layer 2/MAC address details

  - by user69971

  A layer 2 Ethernet frame is sent with a source and destination MAC address. Given a 100Base-TX (copper) trunk between two Cisco switches, I can do a "show interface fa 0/0" on S1 to see the MAC address assigned to the trunking interface, then go to Switch2 and do a "show mac address-table" and find the MAC address of the S1 fa 0/0 interface as a dynamically learned MAC in the table. Given a similar setup with a 1000Base-X (fiber GBIC) trunk, the MAC address shown in "show interface gi 0/0" on S1 does not show up in the MAC address-table of S2. Everything I can find online indicates that 1000Base-X uses largely the same layer 2 format as copper connections. There's some slight alterations - minimum frame size is slightly larger - but the fundamentals of the frame structure appear to be the same, including transmission with a source and destination L2 address. Why doesn't the address of gi 0/0 show up in the MAC address table of the connection switch? The only thing which seems to make sense would be that the GBIC has its own MAC address, almost as if its acting as a mini 2-port switch or hub, with the switch-assigned MAC address showing up on the interface connection and a different MAC address assigned to the fiber side. If this is the case, is there any way to see the GBIC MAC address on the switch? (I've tried to look up the details in IEEE 802.3z but it doesn't seem to be available without an IEEE membership or purchasing the standard. I find the base 802.3 PDFs for download, but not 802.3z.)

  Read the article

• Apache LDAP auth: denied all time

  - by Dmytro

  There is my config (httpd 2.4): <AuthnProviderAlias ldap zzzldap> LDAPReferrals Off AuthLDAPURL "ldaps://ldap.zzz.com:636/o=zzz.com?uid?sub?(objectClass=*)" AuthLDAPBindDN "uid=zzz,ou=Applications,o=zzz.com" AuthLDAPBindPassword "zzz" </AuthnProviderAlias> <Location /svn> DAV svn SVNParentPath /DATA/svn AuthType Basic AuthName "Subversion repositories" SSLRequireSSL AuthBasicProvider zzzldap <RequireAll> Require valid-user Require ldap-attribute employeeNumber=12345 Require ldap-group cn=yyy,ou=Groups,o=zzz.com </RequireAll> </Location> The Require valid-user is work. But ldap-attribite, ldap-filter, ldap-group does not work - denied in logs all time. I spent a lot of time but can't understand what's going on. This is the example of my logs: [Tue Sep 25 16:42:26.772006 2012] [authz_core:debug] [pid 23087:tid 139684003014400] mod_authz_core.c(802): [client 1.1.1.1:52624] AH01626: authorization result of Require valid-user : granted [Tue Sep 25 16:42:26.772014 2012] [authz_core:debug] [pid 23087:tid 139684003014400] mod_authz_core.c(802): [client 1.1.1.1:52624] AH01626: authorization result of Require ldap-attribute employeeNumber=12345: denied I checked all info with ldapsearch: there is a valid username, employee ID and other...

  Read the article

• Netgear GS724Tv3 and link aggregation Mac OS X Server 10.6.8

  - by Manca Weeks

  I need to link aggregate 2 sets of ports on the Netgear GS724T with my Apple server tower (latest generation). I have 2 built in ports and 2 ports on a PCIe ethernet card. It is not obvious to me how to properly configure the Netgear end. I have access to the Netgear box through its web interface, just don't know how to properly set the settings. I tried going to Netgear for help, but they said my software support has expired. I bought this unit on their recommendation - they say it is compatible with 802.3ad protocol. I cannot locate any references to this protocol in the manual and I noticed some people in formus say that this device is actually not compatible with 802.3ad and that Netgear is misleading potential customers by saying it is. Any help will be appreciated. Thanks, M My own answer - posted as edit because of restrictions on my user: OK folks, turns out one must use a Windows machine on this one or nothing makes sense. I was unable to get much farther than viewing the default inactive LAGs because in Firefox and Safari on Mac things don't make much sense - i.e. the Apply buttons (supposedly JavaScript) don't work. You can view the configurations, but none of the modifications you make stick. Then, in Switching - LAGs, choose the ports to include and make sure you switch the LAG type from Static to LACP and all is well. Haven't tested the performance of the config yet, but both sides appear to be happy with the configuration. Apple server says link active and so does the Netgear. Will report if any other discoveries. Thanks for all who read and to user84104 for responding. M

  Read the article

• Wireless driver activation problem in compaq c700 in ubuntu 9.04

  - by Fazil

  I am using ubuntu 9.04, i cant access my wireless driver, i activate the madwifi in administrationhardware drivers, but i could'nt activated the wireless too. when i type lspci i get the following message, ################################################## # 00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 04) 00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 04) 00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 04) 00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 04) 00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 04) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f4) 00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller (rev 04) 00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 04) 01:00.0 Ethernet controller: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter (rev 01) 02:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) ################################################## but when i tried in windows i found that the driver for my laptop is ################################################ atheros AR5007 802.11b/g WiFi Adapter ################################################ so what can i do for solving this problem.

  Read the article

• Home network with two isolated separate subnets, running on cablemodem/router and WRT-router.

  - by Johan Allgoth

  I have a new connection with a nice new router/cable-modem. I'd like to setup it up optimally and needs some pointers. I am a complete n00b when it comes to routing. I want to end up with two separate subnets, 10.1.2.0/24 and 192.168.1.0/24 each available on their own wireless channel/SSID. Both firewalled. I want my wired computers on the gigabit switch, optimally with public ips. I want to be able to reach 192.168.1.0/24 from 10.1.2.0/24, but not vice versa. Everyone should have internet access. Hardware and capabilities: Netgear CG3100. Handles cable connection. Gigabit switch. 802.11n. Can do DHCP, firewall, NAT etc. Can choose subnet. Can turn of NAT and if so hand out up to 4 public ips. Somewhat challenged when it comes to configuration. WRT-router. Runs DD/Open-WRT very stable. 100 Mbit switch. 802.11.g Can do DHCP, firewall, NAT etc. Can choose subnet. Highly configurable. I hope to be able to keep 10.1.2.0/24 on the CG3100, for speed reasons and 192.168.0.0/24 on the WRT-router for quota and user control reasons. On my 10.1.2.0/24 network I plan on running servers for various services. Should I turn of NAT on the WRT-router? Or on the cable modem? Activate what in that case? Is double NAT always f-ed up?

  Read the article

• ipmi - can't ping or remotely connect

  - by Fidel

  I've tried configuring the IPMI controller to accept remote connections, but I can't even ping it. Here is it status: #/usr/local/bin/ipmitool lan print 2 Set in Progress : Set Complete Auth Type Support : NONE PASSWORD Auth Type Enable : Callback : : User : NONE PASSWORD : Operator : PASSWORD : Admin : PASSWORD : OEM : IP Address Source : Static Address IP Address : 192.168.1.112 Subnet Mask : 255.255.255.0 MAC Address : 00:a0:a5:67:45:25 IP Header : TTL=0x40 Flags=0x40 Precedence=0x00 TOS=0x10 BMC ARP Control : ARP Responses Enabled, Gratuitous ARP Enabled Gratituous ARP Intrvl : 8.0 seconds Default Gateway IP : 192.168.1.1 Default Gateway MAC : 00:00:00:00:00:00 802.1q VLAN ID : Disabled 802.1q VLAN Priority : 0 RMCP+ Cipher Suites : 0,1,2,3 Cipher Suite Priv Max : uaaaXXXXXXXXXXX : X=Cipher Suite Unused : c=CALLBACK : u=USER : o=OPERATOR : a=ADMIN : O=OEM # /usr/local/bin/ipmitool user list 2 ID Name Enabled Callin Link Auth IPMI Msg Channel Priv Limit 1 true false true true USER 2 admin true false true true ADMINISTRATOR # /usr/local/bin/ipmitool channel getaccess 2 2 Maximum User IDs : 5 Enabled User IDs : 2 User ID : 2 User Name : admin Fixed Name : No Access Available : callback Link Authentication : enabled IPMI Messaging : enabled Privilege Level : ADMINISTRATOR # /usr/local/bin/ipmitool channel info 2 Channel 0x2 info: Channel Medium Type : 802.3 LAN Channel Protocol Type : IPMB-1.0 Session Support : multi-session Active Session Count : 0 Protocol Vendor ID : 7154 Volatile(active) Settings Alerting : disabled Per-message Auth : disabled User Level Auth : disabled Access Mode : always available Non-Volatile Settings Alerting : disabled Per-message Auth : disabled User Level Auth : disabled Access Mode : always available # /usr/local/bin/ipmitool chassis status System Power : on Power Overload : false Power Interlock : inactive Main Power Fault : false Power Control Fault : false Power Restore Policy : unknown Last Power Event : Chassis Intrusion : inactive Front-Panel Lockout : inactive Drive Fault : false Cooling/Fan Fault : false # arp Address HWtype HWaddress Flags Mask Iface 192.168.1.112 ether 00:A0:A5:67:45:25 C bond0 # /usr/local/bin/ipmitool -I lan -H 192.168.1.112 -U admin -P admin chassis power status Error: Unable to establish LAN session Unable to get Chassis Power Status In summary. It exists on the ARP list so arp's are being broadcast. I can't ping it and can't connect to it. Can anyone spot any glaring mistakes in the configuration? Many thanks, Fidel

  Read the article

• How do I keep a bridge enabled on a bonded interface?

  - by jlawer

  I'm working on setting up a pair of CentOS 6.3 servers that will run a couple of KVM vms and have come across a problem setting up a bridge on a bond. I am using Mode 4 (802.3ad) bonding on a pair of stacked Dell Powerconnect 5524 switches connecting to R320 servers. There are 2 links (1 to each switch) that form a Link Aggregation Group (802.3ad / LACP bonding). On top of the bond I have VLAN Tagging. I've verified this is a problem on multiple other bonding modes so it isn't just a mode 4 issue. I am testing what happens when 1 link is dropped (ie switch dies, cable breaks, etc). If I don't have a bridge (for KVM), everything works fine, failover happens as expected. If I have the bridge enabled, it works fine until failover (unplugging a cable). When failover happens /var/log/messages shows the slave link going down, followed within a second by: kernel: br1: port 1(bond0.8) entering disabled state The thing is /proc/net/bonding/bond0 shows the link is up as expected (simply with only 1 slave instead of 2). If I plug the cable back in it recovers and brings the bridge back to an enabled state. I actually have tested this while a ping is occuring and if the timing is right a packet will actually leave the system after the link is lost, but before the disabled message occurs. This disabled state I assumed was STP, but I have disabled STP on the bridge configuration and this issue still occurs. brctl showstp br1 still shows the link as disabled when it is running without a slave. I also switched between the nics in the server (I have 2x Broadcom & 4x intel). It doesn't matter which configuration I have. Does anyone know of a way to force the bridge to stay enabled or why its detecting the bond as disabled, when it isn't?

  Read the article

• how to set up dual wireless routers (G and N) with single broadband connection

  - by user15973

  A local cafe has an 802.11g wireless router attached to either an 8- or 12Mbs broadband connection. Although many customers still have -g devices, an increasing number are showing up with 802.11n devices (e.g. Mac laptops, iPads). The cafe owner is content with his router's area coverage, but he would like for his customers to be able to take advantage of the higher -n download speeds. He could simply replace the -g router with a -n router, but reportedly -n routers slow down considerably when servicing both -g and -n connections. Another option would be to buy the -n router, run an Ethernet cable between the two routers, and (of course) hook up the broadband connection to one of the two routers. Still another option would be to attach an ordinary, wired switch to the broadband connection and then attach both routers to the switch. Aside from the cost issue, what are the tradeoffs of those approaches? Which would you recommend, and why? Is there a better option than the ones I mentioned? Thank you in advance for your advice.

  Read the article

• XP/Intel wirelss only showing 'hpsetup' ad-hoc network that isn't there

  - by ewall

  Trying to help my friend with her work XP laptop, which recently stopped seeing any wireless SSIDs except the SSID 'hpsetup' (presumably from a wireless-enabled HP printer). Relevant information: The laptop is a Lenovo T500 (Centrino 2 chipset) with XP SP3. The network adapter is Intel WiFi Link 5300 AGN (built-in). The latest version (13.5) of the Intel drivers only are installed, not the Intel config software, so XP is using the Wireless Zero-Config manager. The wireless router is a NetGear WGR614 v7 with 802.11b/g. The SSID is broadcasting, and all the other laptops in the house can see and connect to it. On the laptop, I have tried repairing the network connection, disabling power management, turning off 802.11a & n radio, and more... but it didn't help. Some of the wireless settings are managed by Group Policy from her office (I get the "At least one of your changes was not applied successfully to your wireless configuration" message). It is enforced to connect to "Access point (infrastructure) networks only". The real kicker is that my laptop does not an SSID named 'hpsetup' here, but it can see several broadcasted SSIDs including the one we want, while my friend's laptop doesn't see any SSID except 'hpsetup'. Any suggestions?

  Read the article

• Wireless keeps shutting off in Windows 7

  - by Nathan Adams

  I have Windows 7 Ultimate 32bit installed on a Dell Latitude XT Tablet and for the life of me I can't figure out this really weird problem. The symptom is that the Wireless will disconnect from the AP and if I tell it to scan again, it says there are no APs in the area. I do have another wireless card in the laptop and if I disable the first one and enable the second, I am able to get onto the wireless however if I want to use the first card again I have to restart. I tried enabling/disabling the device, nothing will kick start the wireless again in the first card without a restart. I even tried different drivers. So, it seems it is random but it does occur more often when there is increased network activity (ie downloading a large file). The laptop doesn't seem to be overheating. I have tried the following: Under "Change Advanced Power Settings" for the current power profile, I set the "Wireless Adapter settings" to "Maximum Performance". Under device manger, I went to the card in question, and went to the advanced tab and set the "Power Saving mode" to "MAX_PSP" Both cards I have seem to exhibit the behavior after awhile. Both models of those cards are: Dell Wireless 1505 Draft 802.11n WLAN Mini-Card Gigabyte GN-WS30N 802.11n mini WLAN Card Has anyone have any ideas or ran into this before?

  Read the article

• Wifi Works with Android and Windows 8 but not Linux and Win 7

  - by eramm

  Support has told me that our company wide wifi network is setup to support mobile phones only. However it doesn't make sense to me that they can identify a mobile device rather they have setup the Access Point to use a protocol that is only supported on Android and Windows phones. Because the Access Point supports Windows mobile this means that laptops running Windows 8 can also connect to the Access Point (proven). So it stands to reason that since Android is based on Linux there must be a way to connect using Linux as well. iwlist shows IEEE 802.11i/WPA2 Version 1 Group Cipher : TKIP Pairwise Ciphers (2) : TKIP CCMP Authentication Suites (1) : 802.1x WIreshark seems to show that a connection is being made to a website to get a certificate and use a Domain Controller for authentication. Questions: 1) what protocol could they be using that is supported on Win Mobile and Android but not on Win 7 and Linux (Debian) ? 2) what tools can I use to help me discover what protocol i need to support ? I have used iwlist and wireshark but I was not able to glean to much useful information from them. I can post the results if needed. 3) is there an app i can use on my Android phone to help me understand what kind of network it is connecting to ? I can provide more information if you tell me how to get it. I just don't know what I am looking for.

  Read the article

• How can I start hostednetwork on Windows 7?

  - by Pirozek

  When I type in admin console command to start hostednetwork netsh wlan start hostednetwork it gives me this: The hosted network couldn't be started. The group or resource is not in the correct state to perform the requested operation. There is a hotfix from Microsoft but it didn't help me. Any advice? C:\Users\Pirozek>netsh wlan show driver Interface name: Wireless Network Connection 3 Driver : D-Link AirPlus DWL-G520 Wireless PCI Adapter(rev .B) Vendor : Atheros Communications Inc. Provider : Atheros Communications Inc. Date : 8.7.2009 Version : 8.0.0.171 INF file : C:\Windows\INF\oem108.inf Files : 2 total C:\Windows\system32\DRIVERS\athrx.sys C:\Windows\system32\drivers\vwifibus.sys Type : Native Wi-Fi Driver Radio types supported : 802.11b 802.11g FIPS 140-2 mode supported : Yes Hosted network supported : Yes Authentication and cipher supported in infrastructure mode: Open None Open WEP-40bit Shared WEP-40bit Open WEP-104bit Shared WEP-104bit Open WEP Shared WEP WPA-Enterprise TKIP WPA-Personal TKIP WPA2-Enterprise TKIP WPA2-Personal TKIP Vendor defined TKIP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA-Enterprise CCMP WPA-Personal CCMP WPA2-Enterprise CCMP Vendor defined CCMP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA2-Personal CCMP Authentication and cipher supported in ad-hoc mode: Open None Open WEP-40bit Open WEP-104bit Open WEP WPA2-Personal CCMP

  Read the article

• Wireless driver activation issue in Compaq c700 in Ubuntu 9.04

  - by Fazil

  I am using Ubuntu 9.04, I cant access my wireless driver, I activate the madwifi in administrationhardware drivers, but I could'nt activated the wireless too. when I type lspci I get the following message, ################################################## # 00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 04) 00:1d.0 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 04) 00:1d.1 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 04) 00:1d.2 USB Controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 04) 00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 04) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f4) 00:1f.0 ISA bridge: Intel Corporation 82801HEM (ICH8M) LPC Interface Controller (rev 04) 00:1f.1 IDE interface: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation 82801HBM/HEM (ICH8M/ICH8M-E) SATA AHCI Controller (rev 04) 00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 04) 01:00.0 Ethernet controller: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter (rev 01) 02:01.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) ################################################## but when I tried in Windows I found that the driver for my laptop is ################################################ atheros AR5007 802.11b/g WiFi Adapter ################################################ so what can I do for solving this problem.

  Read the article

• Getting dwl-g122 to work on ubuntu

  - by User1

  I have a USB WiFi adapter, D-Link dwl-g122. I'm running Ubuntu 10.4. My laptop has a built-in wireless card that is connecting fine to the router. I plug in the usb and it never really connects. Here are some details: iwconfig wlan1 IEEE 802.11bg ESSID:"\x0B\xE1..." Mode:Managed Frequency:2.457 GHz Access Point: Not-Associated Tx-Power=19 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on lshw -c network: *-network:1 description: Wireless interface physical id: 3 logical name: wlan1 serial: 00:13:46:8b:xx:xx capabilities: ethernet physical wireless configuration: broadcast=yes multicast=yes wireless=IEEE 802.11bg dmesg [ 1096.814176] wlan1: direct probe to AP xxx (try 1) [ 1096.820960] wlan1: direct probe responded [ 1096.820969] wlan1: authenticate with AP xxx (try 1) [ 1096.823790] wlan1: authenticated [ 1096.823869] wlan1: associate with AP xxx (try 1) [ 1096.827667] wlan1: RX AssocResp from xxx (capab=0x411 status=0 aid=1) [ 1096.827674] wlan1: associated [ 1142.590912] wlan1: deauthenticating from xxx by local choice (reason=3) lsmod|rt2 rt2500usb 19643 0 rt2x00usb 11260 1 rt2500usb rt2x00lib 32133 2 rt2500usb,rt2x00usb mac80211 238896 3 ath5k,rt2x00usb,rt2x00lib cfg80211 148725 4 ath5k,ath,rt2x00lib,mac80211 led_class 3764 3 ath5k,rt2x00lib,sdhci It looks like the driver loads but it doesn't feel like connecting. The behavior is identical even if I blacklist the other wifi card (using an ath5k driver). It's almost like it is using the wrong password or something. Does anyone know what is happening? Is anyone using Ubuntu successful?

  Read the article

< Previous Page | 5 6 7 8 9 10 11 12 13 14 15 16  | Next Page >