Search Results

Search found 26001 results on 1041 pages for 'local ip'.

Page 11/1041 | < Previous Page | 7 8 9 10 11 12 13 14 15 16 17 18  | Next Page >

• Why can't I renew my dynamic IP address?

  - by qwerty

  So, I'm going to explain this from the start. I've started a project with a friend of mine which includes a webspider, that crawls through all pages on a site and stores them in a DB. Since I've never done this before, I didn't think about the amount of requests I was actually sending to the site, and after a day or two I finally got my IP blocked. I need to be able to visit that site as it's very important to me. Not only for my project, but for other reasons too. (and if I'm able to renew my IP I'm going to set a delay on the crawler so I don't get blocked & DDOS the site) I have a dynamic IP address, at least that's what my router settings say. I've tried ipconfig /flushdns, ipconfig /release, restart computer. No result. I end up with the same IP address. I've also tried renewing it from the router, however, I think it uses the same method which isn't working. Is it possible that site has blocked my mac address? Can a site even access my mac address?

  Read the article

• Vyatta internet connection + hosted site on same IP

  - by boburob

  Having a small issue setting up a vyatta. The company internet and two different websites are both on the same IP. Server 1 - Has websites hosted on ports 1000 and 3000 and also has a proxy server installed to provide internet connection to the domain Server 2 - Has a website hosted on ports 80 and 433 The vyatta is correctly natting the appropriate traffic to each server, and allowing the proxy to get internet traffic, however I have a problem getting to the websites hosted on these two servers inside the domain. I believe the problem is that the HTTP request is being sent with an IP, eg: 12.34.56.78. The request will reach the website and the server will attempt to send the request back to the IP, however this is the IP of the Vyatta, so it has nowhere else to go. I thought the solution would be something like this: rule 50 { destination { address 12.34.56.78 port 1000 } inbound-interface eth1 inside-address { address 10.19.2.3 } protocol tcp type destination } But this doesnt seem to do it! UPDATE I changed the rules to the following: rule 50 { destination { address 12.34.56.78 port 443 } outbound-interface eth1 protocol tcp source { address 10.19.2.3 } type masquerade } rule 51 { destination { address 12.34.56.78 port 443 } inbound-interface eth1 inside-address { address 10.19.2.2 } protocol tcp type destination } I am now seeing traffic going between the two with Wireshark, but the website will still fail to load.

  Read the article

• centos 6.3 kvm external ip forwarding to guests

  - by user1111702

  I have a centos 6.3 server with kvm installed. The server has 4 external ips and one NIC. 176.9.xxx.xx1 176.9.xxx.xx2 176.9.xxx.xx3 176.9.xxx.xx4 I use the following configuration ifcfg-eth0 as slave to ifcfg-br0 the configuration in ifcfg-eth0 is DEVICE=eth0 ONBOOT=yes BRIDGE=br0 HWADDR=14:da:e9:b3:8b:99 and in the ifcfg-br0 DEVICE=br0 TYPE=Bridge BOOTPROTO=static BROADCAST=176.9.xxx.xxx IPADDR=176.9.xxx.xx1 NETMASK=255.255.255.0 SCOPE="peer 176.9.xxx.xxx" and I have 3 more aliases for br0 , br0:1 to get the trafic from the second external ip DEVICE=br0:1 IPADDR=176.9.xxx.xx2 NETMASK=255.255.255.248 ONBOOT=yes br0:2 to get the trafic from the third external ip DEVICE=br0:1 IPADDR=176.9.xxx.xx3 NETMASK=255.255.255.248 ONBOOT=yes br0:3 to get the trafic from the second external ip DEVICE=br0:1 IPADDR=176.9.xxx.xx4 NETMASK=255.255.255.248 ONBOOT=yes The above settings work fine and I recieve the trafic from all the external ips. My problem is that I want to pass the trafic from external ip to specific virtual guest on my server. ie trafic that comes from 176.9.xxx.xxx2 must pass to virtual machine 1 176.9.xxx.xxx3 must pass to virtual machine 2 176.9.xxx.xxx4 must pass to virtual machine 3 Can you please help me how to achieve this ? What are the settings on the host and what should I do to the guests. Thank you in advance

  Read the article

• Tunneling a public IP to a remote machine

  - by Jim Paris

  I have a Linux server A with a block of 5 public IP addresses, 8.8.8.122/29. Currently, 8.8.8.122 is assigned to eth0, and 8.8.8.123 is assigned to eth0:1. I have another Linux machine B in a remote location, behind NAT. I would like to set up an tunnel between the two so that B can use the IP address 8.8.8.123 as its primary IP address. OpenVPN is probably the answer, but I can't quite figure out how to set things up (topology subnet or topology p2p might be appropriate. Or should I be using Ethernet bridging?). Security and encryption is not a big concern at this point, so GRE would be fine too -- machine B will be coming from a known IP address and can be authenticated based on that. How can I do this? Can anyone suggest an OpenVPN config, or some other approach, that could work in this situation? Ideally, it would also be able to handle multiple clients (e.g. share all four of spare IPs with other machines), without letting those clients use IPs to which they are not entitled.

  Read the article

• Server 2003 R2 - II6- granting access to website via IP with subnet range

  - by John

  We are trying to allow for a client to connect to our website. By default we are Denying all access except for those with the specified IPs we have configured to run, everything before has just been a single IP address. However now we must implement a range of IPs and rather than input thousands of records we want to use the group of computer options in the Grant Access page. However we have it configured to work off of the IP 72.21.192.0 with a subnet mask of 255.255.224.0 They are unable to connect. Looking over our IIS logs they are receiving a 302 error which is the same behavior anyone should get whom is unauthorized to view the page in question. The IP address coming in is 72.21.217.2, so it should be well within the rage of acceptable IP addresses. I'm at a loss as everything I look up tells me to do what we are doing. So any insight would be appreciated. Especially because I'm a software guy not hardware. Thanks!

  Read the article

• Apache local verses external (domain)

  - by Jessy Houle

  I have an Apache server running on Ubuntu server 10, using Passenger for Ruby on Rails. I have configured my site under the sites-enabled directory of Apache and can hit the server with an internal IP address (192.168.X.X) and the site comes back as expected. However, whenever I try to hit the site externally, either through the domain name or the IP address tied to the domain name, the site will not come back. I have a router in the middle with a static IP address, with Port Forwarding turned on (forwarding 80/443) to the server and I'm quite confident the issue isn't there. In fact, I even DMZed to the Ubuntu Server just to make sure. Also, all router firewall options have been turned off. So here is the question... Is there something else I have to do with Ubuntu server to allow externally requested port 80 traffic? Otherwise, is there some settings that need to be set in Apache to allow domain or external IP address port 80 traffic through? I'm pretty new to Apache, so, please take it a bit easy on me :-) Thank you for your responses. -Jessy Houle

  Read the article

• Setup shared internet connection on virtualbox with fixed IP

  - by Tom

  I am a web developer and until recently I have been using ubuntu as my OS. For many reasons, I have switched back to windows. I still want to keep my server on linux platform, so I setup my local server as a virtual machine. Everything works great, but i have a little struggle with the networking. Since I am working in different places and going around clients, I connect to all sorts of network with different settings. That means the possible IP range is very dynamic which causes issues when I work on my local server. At the moment I have a dynamic IP on my host and static IP on my guest. That way I can access the server from my host (by adding record to hosts file). I also have internet connection on the guest. But once i change networks, it does not work (assuming the network has different configuration). My question is, how to setup host-guest networking, so no matter what network I connect to, I can keep my static IP on guest, which is registered in hosts file on my host so I can access the webserver and also I will have internet connection on the guest? Hope it make sense. Thank you

  Read the article

• TCP RST right after FIN/ACK

  - by Nitzan Shaked

  I am having the weirdest issue: I have a web server which sometimes, only on very specific requests, will send a RST to the client after having sent the FIN datagram. First, a description of the setup: The server runs on an Ubuntu 12.04.1 LTS, which itself is a VM guest inside a Win7 x64 host, in bridged mode. ufw is disabled on the host The client runs on a iOS simulator, which runs on OS X Mountain Lion, which is a VM guest (hackintosh) inside a Win7 x64 host, in bridged mode. Both client and server are on the same LAN, one is connected to the home router via an Ethernet cable, and then other thru WiFi. I happened to glimpse over the server's http logs and found that the client sometimes issuing multiple subsequent identical requests. Further investigation led me to discover that this happens when the server sends a RST, and that the client is simply re-trying. I am attaching several tcpdump's: Good1 is the server-side tcpdump of a good session ("good" meaning no RST was generated). Good3 is another sever-side tcpdump of a good session. (The difference between Good1 and Good3 is the order in which ACK's were sent from the server to the client, ACK'ing the client's request. The client's request arives in 2 segements (specifically: one for the http headers, and another for a body containing an empty json object, "{}"). In Good1, the server ACK's both request segments, using 2 ACK segments, after the second request has arrived. In Good3, the server ACK's each request segment with an ACK segment as soon as the request segment arrives. Not that it should make a difference.) Bad1 is a dump, both client- and server-side, of a bad session. Bad2 is another bad session, this time server-side only. Note that in all "bad" sessions, the server ACK's each request segments immediately after having received it. I've looked at a few other bad sessions, and the situation is the same in all of them. But this is also the behavior in "Good3", so I don't see how that observation helps me, of for that matter why it should matter. I can't find any difference between good and bad sessions, or at least one that I think should matter. My question is: why are those RST's being generated? Or at least: how do I go about debugging this, or providing more info here that'll help? Edit 2 new facts that I have learned: Section 4.2.2.13 of the RFC (1122) (and Wikipedia, in the article "TCP", under "Connection Termination") says that a TCP application on one host may close the connection before it has read all of the data in its socket buffer, and in such a case the TCP on the host will sent a RST to the other side, to let it know that not all the data it has sent has been read. I'm not sure I completely understand this, since closing my side of the connection still allows me to read, no? It also means that I can't write any more. I am not sure this is relevant, though, since I see a RST after FIN. There are multiple complaints of this happening with wsgiref (Python's dev-mode HTTP server), which is exactly what I'm using. I'll keep updating as I find out more. Thanks! ~~~~~~~~~~~~~~~~~~~~ Good1 -- Server Side ~~~~~~~~~~~~~~~~~~~~ 13:28:02.308319 IP 192.168.1.51.51479 > 192.168.1.132.5000: Flags [S], seq 94268074, win 65535, options [mss 1460,nop,wscale 4,nop,nop,TS val 943308864 ecr 0,sackOK,eol], length 0 13:28:02.308336 IP 192.168.1.132.5000 > 192.168.1.51.51479: Flags [S.], seq 1726304574, ack 94268075, win 14480, options [mss 1460,sackOK,TS val 326480982 ecr 943308864,nop,wscale 3], length 0 13:28:02.309750 IP 192.168.1.51.51479 > 192.168.1.132.5000: Flags [.], ack 1, win 8235, options [nop,nop,TS val 943308865 ecr 326480982], length 0 13:28:02.310744 IP 192.168.1.51.51479 > 192.168.1.132.5000: Flags [P.], seq 1:351, ack 1, win 8235, options [nop,nop,TS val 943308865 ecr 326480982], length 350 13:28:02.310766 IP 192.168.1.51.51479 > 192.168.1.132.5000: Flags [P.], seq 351:353, ack 1, win 8235, options [nop,nop,TS val 943308865 ecr 326480982], length 2 13:28:02.310841 IP 192.168.1.132.5000 > 192.168.1.51.51479: Flags [.], ack 351, win 1944, options [nop,nop,TS val 326480983 ecr 943308865], length 0 13:28:02.310918 IP 192.168.1.132.5000 > 192.168.1.51.51479: Flags [.], ack 353, win 1944, options [nop,nop,TS val 326480983 ecr 943308865], length 0 13:28:02.315931 IP 192.168.1.132.5000 > 192.168.1.51.51479: Flags [P.], seq 1:18, ack 353, win 1944, options [nop,nop,TS val 326480984 ecr 943308865], length 17 13:28:02.316107 IP 192.168.1.132.5000 > 192.168.1.51.51479: Flags [FP.], seq 18:684, ack 353, win 1944, options [nop,nop,TS val 326480984 ecr 943308865], length 666 13:28:02.317651 IP 192.168.1.51.51479 > 192.168.1.132.5000: Flags [.], ack 18, win 8234, options [nop,nop,TS val 943308872 ecr 326480984], length 0 13:28:02.318288 IP 192.168.1.51.51479 > 192.168.1.132.5000: Flags [.], ack 685, win 8192, options [nop,nop,TS val 943308872 ecr 326480984], length 0 13:28:02.318640 IP 192.168.1.51.51479 > 192.168.1.132.5000: Flags [F.], seq 353, ack 685, win 8192, options [nop,nop,TS val 943308872 ecr 326480984], length 0 13:28:02.318651 IP 192.168.1.132.5000 > 192.168.1.51.51479: Flags [.], ack 354, win 1944, options [nop,nop,TS val 326480985 ecr 943308872], length 0 ~~~~~~~~~~~~~~~~~~~~ Good3 -- Server Side ~~~~~~~~~~~~~~~~~~~~ 13:28:03.311143 IP 192.168.1.51.51486 > 192.168.1.132.5000: Flags [S], seq 1982901126, win 65535, options [mss 1460,nop,wscale 4,nop,nop,TS val 943309853 ecr 0,sackOK,eol], length 0 13:28:03.311155 IP 192.168.1.132.5000 > 192.168.1.51.51486: Flags [S.], seq 2245063571, ack 1982901127, win 14480, options [mss 1460,sackOK,TS val 326481233 ecr 943309853,nop,wscale 3], length 0 13:28:03.312671 IP 192.168.1.51.51486 > 192.168.1.132.5000: Flags [.], ack 1, win 8235, options [nop,nop,TS val 943309854 ecr 326481233], length 0 13:28:03.313330 IP 192.168.1.51.51486 > 192.168.1.132.5000: Flags [P.], seq 1:351, ack 1, win 8235, options [nop,nop,TS val 943309855 ecr 326481233], length 350 13:28:03.313337 IP 192.168.1.132.5000 > 192.168.1.51.51486: Flags [.], ack 351, win 1944, options [nop,nop,TS val 326481234 ecr 943309855], length 0 13:28:03.313342 IP 192.168.1.51.51486 > 192.168.1.132.5000: Flags [P.], seq 351:353, ack 1, win 8235, options [nop,nop,TS val 943309855 ecr 326481233], length 2 13:28:03.313346 IP 192.168.1.132.5000 > 192.168.1.51.51486: Flags [.], ack 353, win 1944, options [nop,nop,TS val 326481234 ecr 943309855], length 0 13:28:03.327942 IP 192.168.1.132.5000 > 192.168.1.51.51486: Flags [P.], seq 1:18, ack 353, win 1944, options [nop,nop,TS val 326481237 ecr 943309855], length 17 13:28:03.328253 IP 192.168.1.132.5000 > 192.168.1.51.51486: Flags [FP.], seq 18:684, ack 353, win 1944, options [nop,nop,TS val 326481237 ecr 943309855], length 666 13:28:03.329076 IP 192.168.1.51.51486 > 192.168.1.132.5000: Flags [.], ack 18, win 8234, options [nop,nop,TS val 943309868 ecr 326481237], length 0 13:28:03.329688 IP 192.168.1.51.51486 > 192.168.1.132.5000: Flags [.], ack 685, win 8192, options [nop,nop,TS val 943309868 ecr 326481237], length 0 13:28:03.330361 IP 192.168.1.51.51486 > 192.168.1.132.5000: Flags [F.], seq 353, ack 685, win 8192, options [nop,nop,TS val 943309869 ecr 326481237], length 0 13:28:03.330370 IP 192.168.1.132.5000 > 192.168.1.51.51486: Flags [.], ack 354, win 1944, options [nop,nop,TS val 326481238 ecr 943309869], length 0 ~~~~~~~~~~~~~~~~~~~~ Bad1 -- Server Side ~~~~~~~~~~~~~~~~~~~~ 13:28:01.311876 IP 192.168.1.51.51472 > 192.168.1.132.5000: Flags [S], seq 920400580, win 65535, options [mss 1460,nop,wscale 4,nop,nop,TS val 943307883 ecr 0,sackOK,eol], length 0 13:28:01.311896 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [S.], seq 3103085782, ack 920400581, win 14480, options [mss 1460,sackOK,TS val 326480733 ecr 943307883,nop,wscale 3], length 0 13:28:01.313509 IP 192.168.1.51.51472 > 192.168.1.132.5000: Flags [.], ack 1, win 8235, options [nop,nop,TS val 943307884 ecr 326480733], length 0 13:28:01.315614 IP 192.168.1.51.51472 > 192.168.1.132.5000: Flags [P.], seq 1:351, ack 1, win 8235, options [nop,nop,TS val 943307886 ecr 326480733], length 350 13:28:01.315727 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [.], ack 351, win 1944, options [nop,nop,TS val 326480734 ecr 943307886], length 0 13:28:01.316229 IP 192.168.1.51.51472 > 192.168.1.132.5000: Flags [P.], seq 351:353, ack 1, win 8235, options [nop,nop,TS val 943307886 ecr 326480733], length 2 13:28:01.316242 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [.], ack 353, win 1944, options [nop,nop,TS val 326480734 ecr 943307886], length 0 13:28:01.321019 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [P.], seq 1:18, ack 353, win 1944, options [nop,nop,TS val 326480735 ecr 943307886], length 17 13:28:01.321294 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [FP.], seq 18:684, ack 353, win 1944, options [nop,nop,TS val 326480736 ecr 943307886], length 666 13:28:01.321386 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [R.], seq 685, ack 353, win 1944, options [nop,nop,TS val 326480736 ecr 943307886], length 0 13:28:01.322727 IP 192.168.1.51.51472 > 192.168.1.132.5000: Flags [.], ack 18, win 8234, options [nop,nop,TS val 943307891 ecr 326480735], length 0 13:28:01.322733 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [R], seq 3103085800, win 0, length 0 13:28:01.323221 IP 192.168.1.51.51472 > 192.168.1.132.5000: Flags [.], ack 685, win 8192, options [nop,nop,TS val 943307892 ecr 326480736], length 0 13:28:01.323231 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [R], seq 3103086467, win 0, length 0 ~~~~~~~~~~~~~~~~~~~~ Bad1 -- Client Side ~~~~~~~~~~~~~~~~~~~~ 13:28:11.374654 IP 192.168.1.51.51472 > 192.168.1.132.5000: Flags [S], seq 920400580, win 65535, options [mss 1460,nop,wscale 4,nop,nop,TS val 943307883 ecr 0,sackOK,eol], length 0 13:28:11.375764 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [S.], seq 3103085782, ack 920400581, win 14480, options [mss 1460,sackOK,TS val 326480733 ecr 943307883,nop,wscale 3], length 0 13:28:11.376352 IP 192.168.1.51.51472 > 192.168.1.132.5000: Flags [.], ack 1, win 8235, options [nop,nop,TS val 943307884 ecr 326480733], length 0 13:28:11.378252 IP 192.168.1.51.51472 > 192.168.1.132.5000: Flags [P.], seq 1:351, ack 1, win 8235, options [nop,nop,TS val 943307886 ecr 326480733], length 350 13:28:11.379027 IP 192.168.1.51.51472 > 192.168.1.132.5000: Flags [P.], seq 351:353, ack 1, win 8235, options [nop,nop,TS val 943307886 ecr 326480733], length 2 13:28:11.379732 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [.], ack 351, win 1944, options [nop,nop,TS val 326480734 ecr 943307886], length 0 13:28:11.380592 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [.], ack 353, win 1944, options [nop,nop,TS val 326480734 ecr 943307886], length 0 13:28:11.384968 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [P.], seq 1:18, ack 353, win 1944, options [nop,nop,TS val 326480735 ecr 943307886], length 17 13:28:11.385044 IP 192.168.1.51.51472 > 192.168.1.132.5000: Flags [.], ack 18, win 8234, options [nop,nop,TS val 943307891 ecr 326480735], length 0 13:28:11.385586 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [FP.], seq 18:684, ack 353, win 1944, options [nop,nop,TS val 326480736 ecr 943307886], length 666 13:28:11.385743 IP 192.168.1.51.51472 > 192.168.1.132.5000: Flags [.], ack 685, win 8192, options [nop,nop,TS val 943307892 ecr 326480736], length 0 13:28:11.385966 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [R.], seq 685, ack 353, win 1944, options [nop,nop,TS val 326480736 ecr 943307886], length 0 13:28:11.387343 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [R], seq 3103085800, win 0, length 0 13:28:11.387344 IP 192.168.1.132.5000 > 192.168.1.51.51472: Flags [R], seq 3103086467, win 0, length 0 ~~~~~~~~~~~~~~~~~~~~ Bad2 -- Server Side ~~~~~~~~~~~~~~~~~~~~ 13:28:01.319185 IP 192.168.1.51.51473 > 192.168.1.132.5000: Flags [S], seq 1631526992, win 65535, options [mss 1460,nop,wscale 4,nop,nop,TS val 943307889 ecr 0,sackOK,eol], length 0 13:28:01.319197 IP 192.168.1.132.5000 > 192.168.1.51.51473: Flags [S.], seq 2524685719, ack 1631526993, win 14480, options [mss 1460,sackOK,TS val 326480735 ecr 943307889,nop,wscale 3], length 0 13:28:01.320692 IP 192.168.1.51.51473 > 192.168.1.132.5000: Flags [.], ack 1, win 8235, options [nop,nop,TS val 943307890 ecr 326480735], length 0 13:28:01.322219 IP 192.168.1.51.51473 > 192.168.1.132.5000: Flags [P.], seq 1:351, ack 1, win 8235, options [nop,nop,TS val 943307890 ecr 326480735], length 350 13:28:01.322336 IP 192.168.1.132.5000 > 192.168.1.51.51473: Flags [.], ack 351, win 1944, options [nop,nop,TS val 326480736 ecr 943307890], length 0 13:28:01.322689 IP 192.168.1.51.51473 > 192.168.1.132.5000: Flags [P.], seq 351:353, ack 1, win 8235, options [nop,nop,TS val 943307890 ecr 326480735], length 2 13:28:01.322700 IP 192.168.1.132.5000 > 192.168.1.51.51473: Flags [.], ack 353, win 1944, options [nop,nop,TS val 326480736 ecr 943307890], length 0 13:28:01.326307 IP 192.168.1.132.5000 > 192.168.1.51.51473: Flags [P.], seq 1:18, ack 353, win 1944, options [nop,nop,TS val 326480737 ecr 943307890], length 17 13:28:01.326614 IP 192.168.1.132.5000 > 192.168.1.51.51473: Flags [FP.], seq 18:684, ack 353, win 1944, options [nop,nop,TS val 326480737 ecr 943307890], length 666 13:28:01.326710 IP 192.168.1.132.5000 > 192.168.1.51.51473: Flags [R.], seq 685, ack 353, win 1944, options [nop,nop,TS val 326480737 ecr 943307890], length 0 13:28:01.328499 IP 192.168.1.51.51473 > 192.168.1.132.5000: Flags [.], ack 18, win 8234, options [nop,nop,TS val 943307896 ecr 326480737], length 0 13:28:01.328509 IP 192.168.1.132.5000 > 192.168.1.51.51473: Flags [R], seq 2524685737, win 0, length 0 13:28:01.328514 IP 192.168.1.51.51473 > 192.168.1.132.5000: Flags [.], ack 685, win 8192, options [nop,nop,TS val 943307896 ecr 326480737], length 0 13:28:01.328517 IP 192.168.1.132.5000 > 192.168.1.51.51473: Flags [R], seq 2524686404, win 0, length 0

  Read the article

• Multiple IP addresses on one NIC register twice in DNS server

  - by Brad B.

  Hi, We've got a build server (Windows Server 2008 SP2, 64-bit) which has one NIC and two IP addresses registered to that NIC (192.168.1.30 and 192.168.1.31). The build server is registering two identical Host (A) records for itself in our DNS server: buildserver.example.com = 192.168.1.30 buildserver.example.com = 192.168.1.31 I know in the "Advanced TCP/IP Settings" window for the build server's NIC, under the "DNS" tab, there is a check box labeled "Register this connection's addresses in DNS". I only want ONE of the IP addresses (ending in .30) to be registered in DNS not both of them. Can that be done? My best guess is to disable the "Register this connection's addresses in DNS" and manually add the Host (A) record to our DNS server. Thanks for any help!

  Read the article

• Permanently change IP address on SuSE 10

  - by Long Ngo

  I am trying to change IP address of a SuSE 10 machine that is running Tomcat. I need to create a shell script to do this so could not use YaST. As some sites suggested on my Google search, I edited the files in /etc/sysconfig/network/ifcfg-eth-* to change the IP address. After that, I restarted the network service by calling /etc/init.d/network restart. The network card restarting just fine. I, then, restarted tomcat web service. However, when I browsed the new IP address using browser, I got an "Request denied" message. Can anyone please tell me how I could do this? Thanks

  Read the article

• ip namespace non-root shell

  - by user2730940

  I am trying to run ssh command to another ip namespace. I can do it right now, but it runs as root. I want to run it as a normal user. I want to know if there is a way to enter a non-root shell in another network namespace. I know you can use this to enter a root shell in another namespace: sudo ip netns exec <namespace> bash Alternatively, is there a way to run single commands as a non-root user? I know you can run commands as root with this: sudo ip netns exec <namespace> <command>

  Read the article

• 3G/Edge/GPRS IP addresses and geocoding

  - by LookitsPuck

  Hey all! So, we're looking to develop a mobile website. On this mobile website, we'd like to automatically populate a user's location (with proper fallback) based on their IP address. I'm aware of geocoding a location based on IP address (mapping to latitude, longitude and then getting the location with that information). However, I'm curious how accurate this information is? Are mobile devices assigned IP's when they utilize 3G, EDGE, and GPRS connections? I think so. If that is so, does it map to a relatively accurate location? It doesn't have to be spot on, but relatively accurate would be nice. Thanks! -Steve

  Read the article

• Server with 3 public IP and iptables

  - by Juan

  I have a linux box with two NIC cards: eth0 and eth1. In one card i have 3 public IP: eth0 = 10.10.10.1, eth0:1= 10.10.10.2 and eth0:2= 10.10.10.3 In the other card i have one local IP eth1 = 192.9.200.1 I want to redirect all the wan traffic for 10.10.10.2 to the LAN 192.9.200.2 and the same for 10.10.10.3 to 192.9.200.3 I have tried with this rule but doesn't work iptables -t nat -A PREROUTING -i eth0 -d 10.10.10.2 -j DNAT --to-destination 192.9.200.2 iptables -t nat -A PREROUTING -i eth0 -d 10.10.10.3 -j DNAT --to-destination 192.9.200.3 IP forward is enabled in /etc/sysctl.conf Can you help me, please.

  Read the article

• Adding IP address to OpenVZ VPS (OpenVZ Web Panel)

  - by andy

  I apologise if I sound at all dumb. This is my first dedicated server having used a VPS for over a year and I'm trying to setup a VPS on this new server. I purchased a subnet from my hosting provider that I believe allows me 6 usable IP addresses: 177.xx.xxx.201 - 177.xx.xxx.206 The subnet address looks like this: 177.xx.xxx.200/29. I've gone on my server and added them like it said on a wiki like so: ip addr add 177.**.***.201/29 dev eth0 I done that for all six and now when I go to them in the browser they point to my server. The problem is, I'm using OpenVZ web panel to create VMs (http://code.google.com/p/ovz-web-panel/) so I created a VM and assigned one of those IPs to it. However when SSHing to that IP it SSH's to the dedicated server and not the VM. Am I missing something?

  Read the article

• is it possible to get IP address of a wifi that you are not connected to

  - by coltonon

  Just like the question states. Is it somehow possible to get the IP address of a network that you don't have access to? For example, if you click the little wifi button on your task bar, and highlight your cursor over one of the options, you get some info. But your external IP address is actually the address of the router, isn't it? Which would mean you would have to connect to the wifi, and then the router to get an IP address, correct? I realy just want a simple answer: No or Yes and here's how

  Read the article

• On setting up Apache and IIS to share the same IP

  - by miCRoSCoPiCeaRthLinG

  Hello, There are two different web-apps running on two (physically) different servers on our network... one of IIS and another one on Apache - both on port 80 since two machines are accessible by different IPs on our internal network. Now I want to expose both these services to the world. My idea is to somehow make the incoming connection redirect to the appropriate server based on user's choice of subdomain. Example xxx.domain.com maps to the IIS (Internal IP: 1.2.3.4) yyy.domain.com maps to Apache (Internal IP: 5.6.7.8) To the world, both these servers will share the same public IP. What kind of a configuration am I looking at and how do I go about trapping the subdomain requests and redirecting to the appropriate server? Thanks, m^e

  Read the article

• removing the .local in local network name serving

  - by Paul Nathan

  I have several local machines; I use a OSX 10.6 machine to do most of the serving. Annoyingly, it postfixes its network name with .local. How would I set up a system so that I could access it by its hostname? server: httpd apache2 default install I am accessing it with a web browser(surprisingly). also when I ping my osx machine as name, it doesn't work; ping name.local does work.

  Read the article

• Can't ping some IP addresses in the same subnet (LAN) Windows 2011 Server

  - by Ricardo

  Hi I’m running in Windows Small Server 2011 server standard (192.168.1.108), it’s my dhcp and dns server too, but suddenly all other users can’t get internet. My gateway is 192.168.1.1. After a lots of tested I can saw that my server can’t get into the router (192.168.1.1), and also into some others computers, but some other computers answer the ping command. In fact the same computer with the IP 192.168.1.9 didn't answer, but with the IP 192.168.1.63, it response! I have no routers, firewall, vlans or anything that disallow the traffic between computers, in fact when I changed the server IP address (192.168.1.109), I be able to ping the other computers and gateway, but if a back to the 192.168.1.108 the trouble comeback. I hope you can help me with this issue Ricardo

  Read the article

• LameUser trying - apache2 webserver authentication - IP range to access without pass prompt others with it

  - by Mikee

  I have (maybe silly) question regarding the apache2 webserver and security - I am trying to archieve this: Users connecting from 192.168.1.24 not to be prompted for password and allowed Others asked for username and password if correct then connect. I am trying to do this for the whole directory /var/www No matter whether I put the code into .htaccess file or in httpd.conf it doesn't work for me. Order deny,allow Deny from all AuthName "PassRequest" AuthType Basic AuthUserFile /var/.htpasswd Require valid-user Allow from 192.168.1.24 Satisfy Any If I try to connect to the page I am allowed from both the allowed IP or any other, If I remove the satisfy any line then I am prompted for password, if I remove the password too and try to connect from different IP I am NOT REFUSED ... is there some module that needs to be activated or why is the IP directive skipped ? It needs to be put in every folder or /var/www/.htaccess is enough ? can I just put it in httpd.conf instead or not ?? I spend last 4 hours trying to google up why it is acting like that, Any help will be highly appreciated :-))

  Read the article

• IP Forwarding and Routing in Windows 2008

  - by Danialzo

  I have Hyper-V running on a windows 2008. I got a new ip stack from the data center to be set on my virtual machines. But I have difficulties to set these IPs on my VMs because they are on different network. my current server ip is xxx.xxx.18.6 with MASK : 255.255.255.224 and the GW is xxx.xxx.18.1 my new ip stack is xxx.xxx.168.176/29 I can use RRAS to achieve this. Do I need to create another NIC? How do I make these VMs reachable from outside?

  Read the article

• Wrong source IP when accessing internet directly from TMG server

  - by jarod1701

  Hi everyone, after implementing a ForeFront TMG server I'm facing only one problem: After I added a second IP to the external adapter I had to manually set "NAT Address Selection" inside the network rule "Internet Access" to the first IP since all others would get blocked by the CISCO firewall. This configuration works as long as traffic comes from the internal network (e.g. browser on clients). Traffic from the TMG directed to the internet always carries the second IP as it's source address and gets blocked. All our other TMGs/ISAs are running fine and I never came across this problem- Does anybody have a clue, coz I don't?! Kevin

  Read the article

• Changing IP every sec with Firefox

  - by Carol

  I looking for ip changer what is faster than PROXY (i tried Elite Proxy Switcher + Firefox add-on, but it's too slow. I set automatic switching to 4 sec and yes he change the ip every 4 sec however it's not enough because it loads pages very slowly.) Secondly I tried the TOR Project but this is not good..because the TOR would be nice and working good however he needs more than 10 seconds, a new identity and it's not to good for me because i want to change my ip lass than 10 sec. So I find the solution. This is IPfucker alias ipFlood (https://addons.mozilla.org/en-us/firefox.../ipflood/) But it does not work on all sites unfortunately...because this is just simulation "Simulate the use of a series of proxy changing at each new connection.". Anyone knows a solution to the problem? Is there an alternative (VPS, Proxy, TOR)? Thanks in advice.

  Read the article

• MAC to IP binding in ASA 5510 / SG 300-52

  - by Sampsa

  I am trying to configure a Cisco ASA 5510 to assign specific IP-addresses to specific MACs. Firmware on my ASA is 8.2(5). I have used this feature in our previous device (Cisco SA-520W). I have also read that this feature is (not yet) implemented. How do I work around this problem, if not by direct assignment? Do I need to specify fixed IP's on concerned devices themselves? I also have a SG 300-52 switch for our LAN. We cannot specify IP-addresses to ports, because we have further switches down the line. Thank you for your help!

  Read the article

• IP assignment in a /28 block

  - by mks

  Need help on setting up firewall router. My config is as below: Public static network ID: x.x.x.48/28 gateway: x.x.x.49 available IP for the hosts: x.x.x.52 to 62 gw_eth0 <-- fw_eth0 - fw_eth1 <-- dmz_switch Four servers are connected on dmz_switch (say s1, s2, s3, s4) all have to use public static IP address from the above block. Any recommendation on IP assignment and route setup? Do I need to subnet the above block further or simply use /32 netmask and point-to-point static routes in the above setup?

  Read the article

• Detect an IP address of a Wireless Access Point device

  - by dempap

  I have a Wireless Access Point device (http://www.szedup.com/show.aspx?id=1706), which I am planning to put into BeagleBoard-xM, in order to achieve wireless communication (LAN). However, I can't find it's IP address. I mean, I have to know it's IP address in order to connect with BeagleBoard-xM via a terminal emulator. For the moment, I have this device connected via Ethernet on my router. My router's setting page shows I have this device connected, but no further information. Is there any way to find the IP address of the Wireless Access Point? I hope of being understood. Any help would be really appreciated.

  Read the article

< Previous Page | 7 8 9 10 11 12 13 14 15 16 17 18  | Next Page >