Search Results

Search found 700 results on 28 pages for 'nas'.

Page 11/28 | < Previous Page | 7 8 9 10 11 12 13 14 15 16 17 18  | Next Page >

• Recovering Data from a Linkstation LS-WXL/R1

  - by kingkool68

  I've been running a Buffalo Linkstation LS-WXL/R1 in RAID1 for a few weeks. Two nights ago we had a brief power outage. Yesterday when I tried to mount the disk it couldn't be found. I logged in to the web admin and it couldn't see any storage attached and no arrays available. Well this sucks. I ended up taking the disks out and mounting them to an Ubuntu virtual machine. They how up as an Array but I can't start the Array to the best of my limited knowledge. I could still see the 6 partitions, so I'm confident the data is there. I can use Photorec (http://www.cgsecurity.org/wiki/PhotoRec) to recover most of the files I want, it just takes some time. Could I make an image of the data partition and mount that in Ubuntu so I can get at the data I want through the file system? 95% of the data on my Linkstation LS-WXL/R1 is backup. I just put a few folders of images on there that I need to get back. I'm already preparing to format the disks when I'm done and re-building the RAID1 array from scratch. Any advice would be appreciated.

  Read the article

• Backup to disk, encrypted, without any installed local software

  - by user30064

  Hi, Ok, this is a tough one, and it might not even be possible, but no harm in asking I guess. I have a Buffalo Terastation file server that I use for network attached storage. After a couple of phone calls to customer services I realised that there is no way to backup to disk encrypted. In effect, I would be carrying unencrypted company data off-site daily, which is obviously unacceptable. I had a go at TrueCrypt, EncFS, and a few others, and as far as I could see all of them required that you install some software on the machine that is to use the file system, which makes sense. Unfortunately the firmware on the Terastation is closed and I cannot install any software (and I can't build from source either, since Buffalo didn't include a compiler). Are there any ways to copy files to disk, where as soon as they are written to the disk they are transparently encrypted, without having to install additional software? I'm not sure it matters too much, but the Terastation firmware is Linux based, although as I mentioned, closed. Many thanks, Andreas

  Read the article

• Is to possible to achieve the SATA II's 3Gbps (375MBps) between home network storage and home computers?

  - by techaddict

  Gigabit ethernet only has 1Gbps (125MBps), whereas SATA II has up to three times that rate. Is it possible to achieve the rate of three times Gigabit ethernet connection which is SATA II speeds, between home network storage and the laptops and desktops with SATA II hard drives? If so, how? Or, is the limitation of a gigabit ethernet port on the laptops the limitng factor, making 1000Gbps the fastest practical transfer speed possible? (practical, meaning that without taking apart the laptop and doing physical modifications like branching a SATA II transfer cable, etc.) -- I just realized -- wouldn't a USB 3.0 cable do the trick? Since USB 3.0 can reach up to 675MBps?

  Read the article

• Security: Managing network shares remotely on Ubuntu?

  - by Industrial

  Hi everyone, I am about to setup a home network server running Ubuntu Server and I'm currently a bit worried about how to handle network shares and permissions in a good way. After working a bit lately with Netgears ReadyNAS's units, I have become really spoiled with how easy it was to set up network shares and giving a specific user different levels of network access to a specific share (forbidden access, read, read/write). How would I accomplish the same with my Ubuntu server through SSH? Thanks a lot

  Read the article

• Wget save cookies not working

  - by TrymBeast

  I've been trying to login in the pyload through the web api, but wget is not saving the cookies and I don't understand why. I'm using the following command: wget --delete-after --keep-session-cookies --save-cookies=my_cookies.txt --post-data="username=USERNAME&password=PASSWORD" http://localhost:8000/api/login But the content of my_cookies.txt is: # HTTP cookie file. # Generated by Wget on 2012-06-23 22:31:33. # Edit at your own risk. When I run the same command but in debug mode I get the following output that includes the set cookie in the header response: DEBUG output created by Wget 1.10.2 (Red Hat modified) on linux-gnueabi. --22:31:11-- http://localhost:8000/api/login Resolving localhost... 127.0.0.1 Caching localhost => 127.0.0.1 Connecting to localhost|127.0.0.1|:8000... connected. Created socket 3. Releasing 0x000504d0 (new refcount 1). ---request begin--- POST /api/login HTTP/1.0 User-Agent: Wget/1.10.2 (Red Hat modified) Accept: */* Host: localhost:8000 Connection: Keep-Alive Content-Type: application/x-www-form-urlencoded Content-Length: 32 ---request end--- [POST data: username=USERNAME&password=PASSWORD] HTTP request sent, awaiting response... ---response begin--- HTTP/1.1 200 OK Content-Length: 34 Content-Type: application/json Cache-Control: no-cache, must-revalidate Set-cookie: beaker.session.id=405390ddc809efed54820638c95d7997; expires=Tue, 19-Jan-2038 04:14:07 GMT; Path=/ Connection: Keep-Alive Date: Sat, 23 Jun 2012 21:31:11 GMT Server: CherryPy/3.1.2 WSGI Server ---response end--- 200 OK hs->local_file is: login (not existing) Registered socket 3 for persistent reuse. TEXTHTML is on. Length: 34 [application/json] Saving to: `login' 100%[=======================================>] 34 --.-K/s in 0s 22:31:11 (1.28 MB/s) - `login' saved [34/34] Removing file due to --delete-after in main(): Removing login. Saving cookies to my_cookies.txt. Done saving cookies. Can anyone tell me what am I doing wrong? Thanks in advance!

  Read the article

• Sharing storage on Linux and Solaris

  - by devlearn

  I'm looking for a solution in order to share a san mounted volume between several hosts running on Linux (RHEL) and/or Solaris (Sparc). Note that I basically need to share a set of directories containing large binary files that are accessed in random R/W mode. I have the following reqs : keep the data on the SAN suitable i/o performances as the software is pretty demanding on IOPS stick to a shared file system as I can't afford a cluster fs (lack of MDS/OSS infrastructure) compression could be really usefull For now I've found only the following candidates : GFS2 , supports Linux only, no compression VxFS , supports Linux and Solaris, compression supported So if you have some suggestions for this list, I'll really welcome them. Thanks in advance,

  Read the article

• Finding a shared HDD attached to the network from my F-13 machine

  - by Ramy

  Sorry for the slew of n00bie questions, but here is one more. I recently partitioned my 1.5TB harddrive according to this question I then bought this to attach the harddrive to my network. The problem is, how do I navigate to the hard drive to move files over the network to the HDD. should this be moved to serverfault? update: the disk isn't even showing up when i call "fdisk -l" (as root). How can I mount it if I can't even find it? [root@Moonface ~]# /sbin/fdisk -l Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00018598 Device Boot Start End Blocks Id System /dev/sda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 64 19458 155777024 8e Linux LVM Disk /dev/dm-0: 53.7 GB, 53687091200 bytes 255 heads, 63 sectors/track, 6527 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/dm-0 doesn't contain a valid partition table Disk /dev/dm-1: 4764 MB, 4764729344 bytes 255 heads, 63 sectors/track, 579 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/dm-1 doesn't contain a valid partition table Disk /dev/dm-2: 101.0 GB, 101032394752 bytes 255 heads, 63 sectors/track, 12283 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/dm-2 doesn't contain a valid partition table

  Read the article

• Is there a way to create a consistent snapshot/SnapMirror across multiple volumes?

  - by Tomer Gabel

  We use a NetApp FAS 6-series filer with an application that spans multiple volumes. For backup purposes I would like to create a consistent snapshot that spans these volumes at the same point in time (or at least with an extremely low delta); additionally, we'd like to to use SnapMirror to replace the production environment to test volumes. The problem is in creating a consistent snapshot/SnapMirror, since these commands are not transactional and do not take multiple parameters. I tried scripting consecutive "snap create" or "snapmirror resync" commands via SSH, but there's always a 0.5-2 second difference between each snapshot. It's currently "good enough", but I'm seriously concerned about the consistency impact with increased load (we're currently in pre-production). Has anyone managed to create a consistent snapshot that spans several volumes? How did you pull it off?

  Read the article

• Will Software RAID And iSCSI Work For A SAN

  - by Justin

  I am looking for a SAN solution, but can't afford even entry level solutions. Basically, the SAN is for development and a proof of concept product. The performance doesn't have to be amazing, but needs to be functional. My buddy says we should just setup sotware RAID and software iSCSI in Linux. Essentially I have a spare server with dual Xeon processors, 4GB of memory, and (2) 500GB 7200RPM drives. It's a bit old but working. I am sure there is reason people don't do software RAID and iSCSI, but will performance be usable? Thinking of configuring the drives in RAID 0 (for performance).

  Read the article

• DD-WRT/openwrt question

  - by Shiki

  Can I squeeze more speed out of my router (when it comes to USB attached storage device on it) with open/DD wrt? (Sorry I don't really know such firmwares.) (Guess it works with ntfs-3g? I don't know.) Feel free to make this a real question. Basically the question: Does the change worth it in the terms of speed? (My router is a TP-Link WR1043N. Edited it out of the question since it would make it too specified.)

  Read the article

• Managing disk in a VM

  - by dst

  I'm replacing my two old rack servers with a new one that has plenty of power to take over the functionality my current servers. The server is a 4U rack mount with 16 3.5" SAS drive bays, two 2.5" bays, a Xeon E3-1230v2 CPU and 32GB of ECC RAM. My issue is the following. I would like to have a FreeBSD file server with ZFS managing disks. However, I need other VMs for e.g. a shell/git server, mail server etc. I'm wondering how to deal with the following issues: I want ZFS to fully manage the disks, so I'm not using any hardware RAID. Should I pass the SAS controller directly to the FreeBSD system as passthrough PCI? I want to maximize the reliability of the setup. On what disks should I install the hypervsor and keep server system disks? For (2) I have the option of having a RAID setup on the SAS controller and using that as system disk to store the hypervisor as well as VM images. However, this makes PCI passthrough to the file server impossible. Another option is using the two 2.5" bays. In terms of reliability how are SSDs compared to e.g. WD RE4 disks? Would it make sense to have two SSDs in software RAID as boot disks for the hypervisor or should I just go with e.g. WD RE4 disks in a software RAID setup. I also need to think about where to store the mails for the mail server, but this could be done over NFS between the VMs. BTW, this is for home use, so the load is not really that big. What I'm looking for is best practices for splitting up a server.

  Read the article

• Raid-z unaccessible after putting one disk offline

  - by varesa

  I have installed FreeNAS on a test server, with 3x 1Tb drives. They are setup in raidz. I tried to offline one of the disks (from the FreeNAS web-ui), and the array became degraded, as I think it should. The problem is with the array becoming unaccessible after that. I thought a raid like that should be able to run fine with one of the disks missing. Atleast very soon after I offline'd and pulled out the disk, the iSCSI share disappeared from a ESXi host's datastores. I also ssh'd into the FreeNAS server, and tried just executing ls /mnt/raid (/mnt/raid/ being the mount point). The whole terminal froze, not accepting ^C or anything. # zpool status -v pool: raid state: DEGRADED status: One or more devices are faulted in response to IO failures. action: Make sure the affected devices are connected, then run 'zpool clear'. see: http://www.sun.com/msg/ZFS-8000-HC scrub: none requested config: NAME STATE READ WRITE CKSUM raid DEGRADED 1 30 0 raidz1 DEGRADED 4 56 0 gptid/c8c9e44c-08e1-11e2-9ba6-001b212a83ea ONLINE 3 60 0 gptid/c96f32d5-08e1-11e2-9ba6-001b212a83ea ONLINE 3 63 0 gptid/ca208205-08e1-11e2-9ba6-001b212a83ea OFFLINE 0 0 0 errors: Permanent errors have been detected in the following files: /mnt/raid/ raid/iscsivol:<0x0> raid/iscsivol:<0x1> Have I understood the workings of a raidz wrong, or is there something else going on? It would not be nice to have the same thing happen on a production system...

  Read the article

• As a small business about to overhaul infrastructure and go virtual, how can we take advantage of all the features of the QNAP TS-439 Pro II+?

  - by Sally

  Specifically, how can we benefit from these current list of features? We're very new to this and I want to be able to talk intelligently to our IT consultant. VMware Ready Citrix Ready Built-in iSCSI target service Virtual Disk Drive (via iSCSI Initiator) Remote Replication Multi-LUN per Target LUN Mapping & LUN Masking Support SPC-3 Persistent Reservation Support What other products should we compare this QNAP to? I appreciate how informative the site is, but they only seem to sell their products through a small number of channels. Is QNAP well known? TIA!

  Read the article

• How to get data out of a Maxtor Shared Storage II that fails to boot?

  - by Jonik

  I've got a Maxtor Shared Storage II (RAID1 mode) which has developed some hardware failure, apparently: it fails to boot properly and is unreachable via network. When powering it on, it keeps making clunking/chirping disk noise and then sort of resets itself (with a flash of orange light in the usually-green LEDs); it then repeats this as if stuck in a loop. In fact, even the power button does nothing now – the only way I can affect the device at all is to plug in or pull out the power cord! (To be clear, I've come to regard this piece of garbage (which cost about 460 €) as my worst tech purchase ever. Even before this failure I had encountered many annoyances about the drive: 1) the software to manage it is rather crappy; 2) it is way noisier that what this type of device should be; 3) when your Mac comes out of sleep, Maxtor's "EasyManage" cannot re-mount the drive automatically.) Anyway, the question at hand is how to get my data out of it? As a very concrete first step, is there a way to open this thing without breaking the plastic casing into pieces? It is far from obvious to me how to get beyond this stage; it opens a little from one end but not from the other. If I somehow got the disks out, I could try mounting the disk(s) on one of the Macs or Linux boxes I have available (although I don't know yet if I'd need some adapters for that). (NB: for the purposes of this question, never mind any warranty or replacement issues – that's secondary to recovering the data.)

  Read the article

• How to interpret IOZone results?

  - by homer5439

  Here are the resuts of running IOZone on an ext3 filesystem on an LVM volume residing on a SAN LUN (it was ran with 5 parallel processes). "Throughput report Y-axis is type of test X-axis is number of processes" "Record size = 4 Kbytes " "Output is in Kbytes/sec" " Initial write " 81628.55 " Rewrite " 83354.72 " Read " 115595.02 " Re-read " 119306.09 " Reverse Read " 47684.20 " Stride read " 10011.09 " Random read " 16751.27 " Mixed workload " 5659.77 " Random write " 1661.85 " Pwrite " 36030.83 Now this is all nice and dandy, but my question is: how do I know whether the values are as good as they could be or there is something to tweak (and if so, what?) The actual usage I will have for that Logical Volume is to act as virtual disk for a VM.

  Read the article

• need advice for storing data setup hardware for client with 80TB per year of data footprint increase

  - by dasko

  hi everyone, i currently have a client that will be adding replicated data from satellite locations in the number of approximately 80TB per year. with this said in year 2 we will have 160TB and so on year after year. i want to do some sort of raid 10 or raid 6 setup. i want to keep the servers to approximately 4u high and rack mounted. all suggestions welcome on a replication strategy. we will be wanting to have one instance of the data in house and the other to be co-located (any suggestions on co-locate sites too?). the obvious hardware will be something like a rack mount server with hot swap trays and dual xeon based type processors. the use of the data is for archives of information, files will be made up of small file sizes. i can add or expand to this question if it is too vague. thanks for looking.

  Read the article

• Should I use "Raid 5 + spare" or "Raid 6"?

  - by Trevor Boyd Smith

  What is "Raid 5 + Spare" (excerpt from User Manual, Sect 4.17.2, P.54): RAID5+Spare: RAID 5+Spare is a RAID 5 array in which one disk is used as spare to rebuild the system as soon as a disk fails (Fig. 79). At least four disks are required. If one physical disk fails, the data remains available because it is read from the parity blocks. Data from a failed disk is rebuilt onto the hot spare disk. When a failed disk is replaced, the replacement becomes the new hot spare. No data is lost in the case of a single disk failure, but if a second disk fails before the system can rebuild data to the hot spare, all data in the array will be lost. What is "Raid 6" (excerpt from User Manual, Sect 4.17.2, P.54): RAID6: In RAID 6, data is striped across all disks (minimum of four) and a two parity blocks for each data block (p and q in Fig. 80) is written on the same stripe. If one physical disk fails, the data from the failed disk can be rebuilt onto a replacement disk. This Raid mode can support up to two disk failures with no data loss. RAID 6 provides for faster rebuilding of data from a failed disk. Both "Raid 5 + spare" and "Raid 6" are SO similar ... I can't tell the difference. When would "Raid 5 + Spare" be optimal? And when would "Raid 6" be optimal"? The manual dumbs down the different raid with 5 star ratings. "Raid 5 + Spare" only gets 4 stars but "Raid 6" gets 5 stars. If I were to blindly trust the manual I would conclude that "Raid 6" is always better. Is "Raid 6" always better?

  Read the article

• Asus WL-520GC + external HDD via Ethernet

  - by Azat

  Has anyone experience of using such combination? Exactly with the same model (or from same model line). How does it works? How hard is to set up all that? What difficulties? I use this router a couple of years, but now i haven't such external drive at my disposal. I want to buy something like Verbatim 47591 or Western Digital WDH1NC10000. (By the way, my router has no USB ports, therefore only Ethernet-ports for external HDD are supported.) Thanks you a lot in advance!

  Read the article

• FreeNAS/ZFS/Raid-Z slightly different disks

  - by muskratt

  I'm considering using FreeNAS and "recycling" some of my older 1TB disks. Two are the exact same model Western Digital while another is Seagate and the fourth is Samsung. Typically, since all disks are not equal, I'll create my arrays on a Windows-based server 1GB undersized to prevent a replacement disk not being large enough. Dell is notorious for sending replacement SATA disks of different brand---knock on wood, no problems yet. Since not all drives are created equally and they can vary a few MBs, is there a way to make the the FreeNas/ZFS/Raid-Z function in the same way I do for my Windows-based servers above? Thanks

  Read the article

• FreeNAS pool configuration - RAID1 + other drives

  - by trnelson

  Simple questions, really. I found this answer with a similar setup, but not sure it answers my question. If it does, I'm curious why since the answer seems a bit unsure: ZFS Hard Drive Configuration in FreeNAS I'm building a server which will be used primarily for backup, plus some media streaming, possibly with Plex. I seem to understand most everything I need, but I'm still a bit confused on how pools work, and how to configure them for my scenario. I will have 2x 2TB WD Red drives, which I plan on using in a mirrored set up (RAID1). This would be for backup, and I'd also like to do offsite backup to my CrashPlan account from this array. I also have a few other drives: 1.5TB, 320GB, 250GB. I'm not sure exactly what to do with them yet, but looking for options. FreeNAS OS will be running from a 16GB USB Flash drive. Would it be wise to use the 1.5TB as a backup-backup, essentially as a mirror or perhaps for snapshots of the 2TB RAID1? I'm still learning about snapshots. Should the 2TB mirrored drives be in their own pool? Should the other drives be set up in their own pools as well, or should they be JBOD in a single pool? They may or may not get much use since the 2TB array is plenty for me. Does a dataset basically mimic the idea of a partition or a network share? In other words, I would map \SERVER\Share to X: on my laptop? Let's say I wanted to use the 250GB drive as an encrypted drive to store all of my cat pictures. Would it have to be in its own pool? If I use jails apps, should they go in the backup RAID1, or in another place? Thank you!

  Read the article

• Windows 7 / TCP/IP network share guide - looking for to resolve failure to mount lacie network drive but works on XP,Linux,Mac.

  - by Rob

  Can anyone advise me of a really good, readable, Windows 7 TCP/IP network share guide, book, or reference. I want this because I cannot mount my Lacie 2big ethernet network drive in Windows 7 (32 bit home), but I can mount it in Windows XP Home 32bit, Ubuntu Linux 10.04 and Apple MacOS X. This drive is being mounted via the accompanying Lacie Ethernet Agent in XP (which I believe uses "Bonjour" protocol), on Mac and Linux it works without further need for software. Another Super User user has the same problem, but no answer: Trouble accessing network drives in Windows 7 I hope my take on the question shows a better willingness to investigate and do some digging - and therefore invite some suggestions to help with this. The drive is detected by Windows 7 (i.e. speech bubble "network drive found") but on trying to open an Explorer window, this remains blank with the Windows busy pointer. I'd prefer not to reinstall Windows 7 to see if that cures the problem, I'd rather understand what is happening/not happening, perhaps even compare differences with Windows XP. Suggestions, please for such guides or even the original problem itself. Update Edit Rewrote question more comprehensively here: Mhttp://superuser.com/questions/304209/looking-for-definitive-answer-to-accessing-a-network-share-via-windows-7-home-and

  Read the article

• Security: Managing network shares remotely on Ubuntu?

  - by Industrial

  Hi everyone, I am about to setup a home network server running Ubuntu Server and I'm currently a bit worried about how to handle network shares and permissions in a good way. After working a bit lately with Netgears ReadyNAS's units, I have become really spoiled with how easy it was to set up network shares and giving a specific user different levels of network access to a specific share (forbidden access, read, read/write). How would I accomplish the same with my Ubuntu server through SSH? Thanks a lot

  Read the article

• Make a drive from one machine appear as a physical disk in another machine.

  - by Roberto Sebestyen

  I want to take a physical disk (or part of a disk) in one machine (call it machine-A) and I want to make it available in another machine (machine-B). But I don't want to map a network drive. I want it to appear in machine-B as a physical drive. Even though it is not a physical drive. The reason I want to do this is i want the ability to create shares in machine-B on that drive. Since I cannot do that on mapped drives, I need to use some utility that fools machine-B to think that it is a physical drive, and treat it as such. Both of these machines are windows server 2003. I heard about NFS, It sounds like what could be the solution to my problem. But isn't that a Linux/Unix protocol? What tools can I use to make this happen? Are there any open source solutions? I don't care what the solution is, as long as it achieves the end result, preferably open source solution though. Thanks for reading guys and gals!

  Read the article

• Does my DLink DNS-323 need to reside on a "192.168.0.0/24" subnet?

  - by Raymond

  I've installed two brand new 2-tib drives in the DLink and plugged it in to my network. I set my router's static address table to include the MAC address of the device; however it doesn't ever "show up." Do I need to use the custom software to administer this device? Do I need to use a "192.168.0.0/24" network in order for this device to work (asking because it states that if DHCP isn't detected, it will default to an address in that range; and my network is not in that range).

  Read the article

• Expendable, Redundant, Easily recoverable

  - by MeIr

  I am desperate at this point, I have been looking for "Big storage" solution for a while on my own and I can't find anything that would suite my needs. But now push came to shove. Current situation: I have about 6TB data storage (already full) - Drobo. Yesterday Drobo died on me and it put me into bad situation - I can't recover my data without buying another Drobo. From extensive research online I realized that Drobo is not the safest bet and by now it seems very poor choice. I ordered new Drobo to try to get my data back, however I don't want to be in the same situation later and continuing using Drobo promises this event to re-occur. What I am looking for: 1) Inexpensive setup. 2) Dynamically extendable - add more drives and/or replace a drive with bigger capacity. 3) Redundant - setup against 1-3 drive failure, will depend on total number of drives. For the sake of argument let's assume for every 4 drives one should be able to fail without data loss. 4) Easy data recovery - let's say unforeseen happens, I would like to be able to recover information without buying new tools or replacements - example: new Drobo. 5) Should be USB or Network Attach Storage 6) No demand on speed. Doesn't have to be fast, I am not doing video editing on the setup. However if option exists, would be nice to have a decent speed. After thoughts: I reviewed few options and FreeNAS looks nice, but it doesn't have #2 - Dynamic extendability. There are work around with Pools but it seems a bit complicated and unnecessary. More over it seems like data safety is a big question - saw some horror stories. Please advise on what options I have and what seems like an optimal solution (if any). I don't care if it has to be Windows or Linux box or any other OS and/or software that has to run on top, but simple solution is more attractive. Thank you! P.S: Feel free to ignore "After thoughts".

  Read the article

< Previous Page | 7 8 9 10 11 12 13 14 15 16 17 18  | Next Page >