Search Results

Search found 98255 results on 3931 pages for 'win7 home user'.

Page 11/3931 | < Previous Page | 7 8 9 10 11 12 13 14 15 16 17 18  | Next Page >

  • Home Networking Questions

    - by Eddie Parker
    Hello: I'm looking to wire my home with CAT-X (where X is probably going to be CAT-6, unless someone can convince me differently. ;) ). I'm seeking advice on what equipment I'll need for the job, and any things I should watch out for. It's a two story half-duplex I'll be wiring, roughly about 1800 sq ft. Here's what I believe I need so far: Bulk CAT-6 Ethernet cabling CM Rated Gigabit switch(es?) Patch panel Equipment for cutting, terminating wire, fishing through walls, etc Wall outlet covers, etc. Questions I have: Does it matter the MHz rating on the Ethernet cable? If so, why? I have two gigabit switches currently, an 8-port and a 5-port. Should I buy one massive switch to cover all the connections I need, or should I just chain the two together and buy a switch for however many other connections I need? Do I really need a patch panel? I understand it keeps the cables looking cleaner than coming out of a hole in the wall, but is there some other product I can use, perhaps combining a switch with a patch panel or some such? Ideally I'll have all this running out of a relatively small closet, so the less components (or smaller) the better. Any advice, links, or suggested product to use/avoid would be appreciated!

    Read the article

  • iTunes Home Sharing only works one way between 2 WinXP PC's on the same LAN

    - by scunliffe
    Both PC's have the latest iTunes installed. PC (A) can "see" that there is a shared library "B library" but attempts to connect to it return this error message: The shared library "{Username}'s Library" is not responding (-3259) Check that any firewall software running on either the shared computer or this computer has been set to allow communication on port 3689. however the reverse works fine. e.g. PC (B) can "see" shared library "A library" and can access all content. Notes: Both PC's have Home Sharing enabled (turned off/on several times to verify). Both PC's have Windows Firewall turned on, but in the exceptions tab, iTunes is allowed, and Port 3689 is also added as a firewall exception (just in case) Both iTunes accounts have been "authorized" on both PC's Both PC's connect via LAN via D-Link DIR-615 router. In the advanced application rules, iTunes has also been added to allow traffic on port 3689 un-hindered. Is there any other magical setting/configuration option that I should be aware of and set in order to get this to work? I could care less about sharing apps etc. I just want the music sharing to work. Update: Solved! It turns out on PC (B) there were multiple accounts set up. 1 of the accounts had the checkbox checked under the windows firewall "On" option which states "No exceptions" thus even though it was added to the exception list on the main user account, this other account was blocking access.

    Read the article

  • No Outbound Internet on Windows Home Server

    - by Kyle B.
    Could someone provide some steps for me to check my internet connection on my Windows Home Server? It seems to have intermittent connectivity issues and I am unsure of how to diagnose the problem because it is a headless (no monitor, no keyboard) machine so the only way to get to the device is via remote desktop (which works fine). When connected to the machine, it doesn't pull up any microsoft.com sites and some other sites it does pull up (i.e. gmail.com) and some it doesn't (stackoverflow.com). To make matters more complicated, it has worked intermittently in the past for reasons unknown. Are there tools I can use to properly diagnose the reason for the connection failure? I can ping 127.0.0.1 just fine, I have internet working on my other router-connected machines, so I'm not sure why this one would fail. Any suggestions would be much appreciated and up-voted :) ** edit - thanks for suggestions guys, I'm going to try these tonight and will update my post. ** edit #2 - I hoping this is a more permanant fix, but I have both changed my port on the router as well as restarted the router at the same time. The internet (for the moment) appears to be working. I will be sure to try everything we have discussed should this problem persist. Thanks, Kyle

    Read the article

  • 12.04 scanner works fine as super-user but is not recognised as a normal user

    - by Eugénio Outeiro
    I have an all-in-one printer Epson SX130, wich I have just tried to install. I got the printer working with no problem, but I couldn't set the scanner up. I have had another all-in-one printer before (Brother DCP-125C), and had just the same problem, so I decided to try the same trick I used to do then, running the scanning program as super-user: $sudo simple-scan and $ sudo xsane Once again, it worked just fine, and I could use the scanner. Anyhow, this solution is a little annoying, because I also have to change the permissions to the files I get scanning like this. I have been searching the internet for solutions and got to know this must have something to do with user groups permissions, but couldn't find a satisfying solution. Is there anyone with an idea? Thank you in advance.

    Read the article

  • Resolving loss of internet bandwidth in home network

    - by Caspar
    Recently, I've decided to connect my laptop at home to my modem/router through Ethernet cables built into my apartment. As these built-in Ethernet cables are usable via plugs built into the walls (called powerline adapters), I use some additional cabling (STP CAT6 cables) from my laptop/router to the plugs. In addition, I don't know any technical details about these built-in cables (as they're not visible), only the maximal bandwidth (1 GBit = Cat6?) that they're supporting. The built-in cables are Cat. 5e Ethernet cables. The problem is now that when I set up the connection, I cannot use the full bandwidth that my internet connection is actually offering (100 Mbit/s), only about 85 Mbit/s between 85 - 88 Mbit/s, despite the fact that all cables involved should support the maximal bandwidth. I know from other tests with one of the Ethernet cables in use that I can use almost 99 Mbit/s when I connect my laptop directly to the router/modem using only this one cable. In addition, it is very unlikely that the length of the resulting cable connection from my laptop to my router involving the built-in cables exceeds 100 m. So, what possible reasons for this loss of bandwidth exist? And how I can fix this issue? I hope this might help resolve the issue: The built-in cables appear to be Cat. 5e Ethernet cables. So, is there any problem when I connect Cat6 Ethernet cables directly to Cat5e Ethernet cables via the plugs?

    Read the article

  • Cannot login to newly created user account

    - by penner
    Trying to switch accounts to my newly created account I get a black screen and then it takes me back to the main login screen after entering the correct password. Upon logging into my previously existing account I get: "System Program Problem Detected" Details: Executable path /usr/bin/Xorg Package: xserver-xorg-core 2:1.11.4-0ubuntu10.1 Details: Crash ... (tons more, but no way to copy paste or save) When I try to su su -l penner I get: No directory, logging in with HOME=/ I manually created the home directory and this error goes away but still no luck with the login. Seems something has gone wrong with the user creation? How can I correct this?

    Read the article

  • Keep user and user profile in different tables?

    - by Andrey
    I have seen in a couple of projects that developers prefer to keep essential user info in one table (email/login, password hash, screen name) and rest of the non essential user profile in another (creation date, country, etc). By non-essential I mean that this data is needed only occasionally. Obvious benefit is that if you are using ORM querying less fields is obviously good. But then you can have two entities mapped to same table and this will save you from querying stuff you don't need (while being more convenient). Does anybody know any other advantage of keeping these things in two tables?

    Read the article

  • Home Server: storage virtualisation, what to choose?

    - by Huygens
    I'm looking for virtualisation solutions for storage and OS for a home server. A sort of private cloud where I manage the storage space independently of the VM one. This question focus on storage management. (I have another question related to the VM/compute instance management). Here my environement and wishes. Server: HP Proliant MicroServer with 8 GB RAM (AMD Turion dual core with AMD-V technology) with 1 250GB system disk and up to 4 HDD (2 TB) for "data" OS types: only Linux (perhaps a *BSD VM in the future) Linux distributions do not matter, I'm familiar with RHEL, Fedora, Suse, Ubuntu, but any other recommandation will be fine The 4 HDD is going to be a software RAID array, probably RAID 5. storage should be "virtualised/cloudified": easy to extend: if I add a NAS on the network, I can include the NAS space capacity within this storage space as one virtual disk. This can be a NAS, an external HDD or another server. cluster FS or S3 style space or OpenStack block storage? Whatever is easier to manage/maintain and easy to integrate/plug to VM/compute instance. I would prefer free (libre, as in a free speach) and open source tools. But it does not have to be free as in a free beer. Note: the VMs I intend to run on top of this server are one dedicated to backup, one for a "owncloud/dropbox"-like service and perhaps one for media server (hosting video and photos). I'm not sure if traditional VMs or compute instance are the most suitable for this.

    Read the article

  • iTunes Home Sharing only works one way between 2 Windows XP PC's on the same LAN

    - by scunliffe
    Both PC's have the latest iTunes installed. PC (A) can "see" that there is a shared library "B library" but attempts to connect to it return this error message: The shared library "{Username}'s Library" is not responding (-3259) Check that any firewall software running on either the shared computer or this computer has been set to allow communication on port 3689. however the reverse works fine. e.g. PC (B) can "see" shared library "A library" and can access all content. Notes: Both PC's have Home Sharing enabled (turned off/on several times to verify). Both PC's have Windows Firewall turned on, but in the exceptions tab, iTunes is allowed, and Port 3689 is also added as a firewall exception (just in case) Both iTunes accounts have been "authorized" on both PC's Both PC's connect via LAN via D-Link DIR-615 router. In the advanced application rules, iTunes has also been added to allow traffic on port 3689 un-hindered. Is there any other magical setting/configuration option that I should be aware of and set in order to get this to work? I could care less about sharing apps etc. I just want the music sharing to work. Update: Solved! It turns out on PC (B) there were multiple accounts set up. 1 of the accounts had the checkbox checked under the Windows firewall "On" option which states "No exceptions" thus even though it was added to the exception list on the main user account, this other account was blocking access.

    Read the article

  • Home Network Stopped Working

    - by James
    I have a home network where a machine running Windows 7 Ultimate N acts as a central hub for other devices to access media. This has been running for around 2 years now and there has been no recent configuration changes. The machine has a static IP address (192.168.0.3), which also has not been changed. A few laptops, Sonos music system and mobiles are using the machine for music/video mostly. Additionally, post 3389 was also open for RDP. I used a no-ip agent to map a hostname so I could RDP to the machine from the internet. As of yesterday when I try to ping the machine, I get PING:Transmit Failed, General Error I noticed however, the IP it is pinging is 0.0.2.233. All shares etc are no longer functioning including RDP. On the machine itself, an IP config shows like nothing has changed. It still shows the expected IP. If I ping itself from its hostname, I get the same error as above. machine has been rebooted, the router has been also. Any ideas where to even start on this?

    Read the article

  • Windows Home Server 2011, No disks "suitable for a backup destination"

    - by Scott Beeson
    I recently installed Windows Home Server 2011 and love it. However, when I try to set up server backups, it says no suitable disks are available. Initially, before I set up my RAID, it found one of my twin drives and said it would work. Once I set up the mirroring, that one is no longer available (obviously). However, I have an internal SATA 1TB drive and an external USB2.0 1TB drive hooked up. Both are recognized by Disk Management. WHS11 still says nothing suitable for backups. The two drives details are as follows: Edit to clarify: The system partition is on Disk 0, not listed below. The two below are the two that SHOULD be available for system backups. Disk 1: Dynamic "Data" (D:) 931.51 GB NTFS, Healthy Disk 3: Basic 200 MB Healthy (EFI System Partition) "Backup" 930.66 GB NTFS, Healthy (Primary Partition) What's a bit odd is that in Disk Management the "Backup" volume does not show a drive letter, even though I assigned Z: (which is reflected in "My Computer". I also cannot make this a dynamic disk as it says it's unsupported by the device.

    Read the article

  • New user profile creation error - Windows cannot open *.exe

    - by Jake
    I have a windows 7 laptop with the user "mydomain\boy" that cannot log in to the laptop. the error message is something like "User profile service cannot log in the user boy". I then logged in with the domain admin account "mydomain\admin" and then went to delete the "mydomain\boy" from my computer system properties advance system settings user profiles settings. I also ensure that the user is deleted from control panel user accounts. I then also deleted the user folder c:\users\boy I also checked that the registry at this location HKLM\software\microsoft\windows nt\currentversion\profilelist\ and ensure that there is no entry for boy. I followed http://support.microsoft.com/kb/947215 using the method 3 "fix it for me" but does not seem to do anything. (or i don't know how to use it). AFTER EVERYTHING DONE ABOVE... Everytime i log in with a new user, be it boy, girl or anything other domain account (other than the admin account already created when I first logged in to begin the fix/break), it takes a long time, and when the "preparing desktop" goes away, it starts to exe cannot open error e.g. regsvr.exe etc.. file association problem with exe QUESTION (phew finally..): Please tell me how to fix it? Thanks!

    Read the article

  • Ubuntu, User Accounts messed up

    - by Vor
    I need to fix Ubuntu Accounts some how but don't really see how it could be done. The problem is: files /etc/passwd and /etc/hostname and /etc/hosts where changed. /etc/passwd After John:x:1000:1000:John,,,:/home/serg:/bin/bash Befoure serg:x:1000:1000:John,,,:/home/serg:/bin/bash /etc/hosts After 127.0.0.1 localhost 127.0.1.1 John-The-Rippe Befoure 127.0.0.1 localhost 127.0.1.1 serg-Protege /etc/hostname After John-The-Ripper Befoure serg-PORTEGE-Z835 I was trying to simply changed this files but can not do this because permission denied. When I'm trying to login as a root I got this message: John@John-The-Ripper:~$ sudo -s [sudo] password for John: John is not in the sudoers file. This incident will be reported The file sudoers is empty: John@John-The-Ripper:~$ vi /etc/sudoers When I type users in cp: John@John-The-Ripper:~$ users John John When I type id, I got this: John@John-The-Ripper:~$ id uid=1000(John) gid=1000(serg) groups=1000(serg) This doesn't work eather: John@John-The-Ripper:~$ usermod -l John serg usermod: user 'serg' does not exist John@John-The-Ripper:~$ adduser serg adduser: Only root may add a user or group to the system. ater. Then I tried to go to the GRUB menu and from there log in as a root. I did this, but however When I tryed to create user serg, It gave me an error that group already exist. When I tried to change /etc/passwd it said 'permission denied' And this doens't do the trick: John@John-The-Ripper:~$ visudo visudo: /etc/sudoers: Permission denied visudo: /etc/sudoers: Permission denied Also The last thing I tried to do is to create a bootable USB and reinstall ubuntu, however I can not open USB-Creator because it asked me a root passwd. But it doesn't work. HELP ME PLEASE =)))

    Read the article

  • Oracle Applications Global User Experience

    - by ultan o'broin
    Today, we're launching Oracle's first ever blog for global user experience (UX) applications issues. We'll be talking about how we design and develop applications for global use, looking at the cultural factors, internationalization (I18n), localization (L10n) and language used for a start. We will also discuss how we study and work with real users so that our customers have applications that allow them to be productive regardless of where they are located in the world. In addition, we will inform you about any globally-related events we know about, and about product features, development frameworks, tools, information and relevant to our worldwide customers. Also, of course, we hope to hear from you, too. If you have anything you want to know about our global user experience, a localization you'd like, or cultural feature you think would be useful, then let us know. If you have any tips or guidelines you'd like to share in this space, then this blog is for you too! As far as global user experience is concerned, you don't have to be lost in translation. Hence the name of the blog!

    Read the article

  • Scoping a home dev server

    - by AbhikRK
    Hi. I’m looking to build a multi-purpose home development server. In this post, I’m looking to outline what I want from such a system, and the ‘why’s of it, to some limited extent, and finally, some rudiments of how I’m looking to go about that. I’m mostly a developer, with just about some sysadmin familiarity. So, please excuse, correct me, and suggest on any ignorance which would come across in the following ;-) It will serve the following goals to start with:- NAS (Looking at using ZFS) Source control repo e.g Git server Database e.g MySQL server Continuous Integration e.g Hudson server Other stuff as and when they come up e.g RabbitMQ etc A development sandbox to play around with new stuff I want to achieve a high uptime for 2-5 as much as possible. They should run as independent services and with minimal maintenance. (e.g TurnKey Linux appliances) I’m thinking of running them as individual Xen DomUs. Then, maybe the NAS can be a Dom0 and 6 can be another DomU. The User for this would be mostly me. I can see 2-4 being sometimes used by 2-3 users, but that would be infrequent. I’m looking for a repeatable setup. Ideally I’d like to automate this setup through Chef or Puppet or something similar. Once everything runs, I want to be able to ssh/screen/tmux into 1-6 from my laptop or any other computer on the LAN/on-the-go. My queries are:- Is putting 1-6, all of them on a single box, a good idea? If so, what kind of hardware should I be looking at, for a low-cost, low-power setup? Although not at present, but in future I might be looking at adding audio/media servers to the mix. Would that impact the answers to 1? I have an old Pentium 3 and 810e motherboard combination. Is there any way I could put it to use? I had a look at the Sheevaplug, and was wondering if I could split off the NAS on its own using that. But ruled it out preliminarily due to its reported heating issues. Is it something i should still consider? Thanks in advance

    Read the article

  • Batch script to create home home directories from list of names

    - by Steven
    I'm trying to create a home directories with permissions from a text file. I can only get the batch file to run the first line. Can anyone tell me why? I initiate the scripts by running go.bat as administrator. go.bat @echo for /f %%a in (users1.txt) do call test.bat %%a test.bat @echo off m: cd \ mkdir %1 icacls %1 /grant %1:(OI)(CI)M cd %1 mkdir public icacls public /inheritance:d icacls public / All:(OI)(CI)(RD) icacls public /grant All:(OI)(CI)R mkdir private icacls private /inheritance:d icacls private /remove All cd \ users1.txt user1 user2 user3

    Read the article

  • Managing User & Role Security with Oracle SQL Developer

    - by thatjeffsmith
    With the advent of SQL Developer v3.0, users have had access to some powerful database administration features. Version 3.1 introduced more powerful features such as an interface to Data Pump and RMAN. Today I want to talk about some very simple but frequently ran tasks that SQL Developer can assist with, like: identifying privs granted to users managing role privs assigning new roles and privs to users & roles Before getting started, you’ll need a connection to the database with the proper privileges. The common ROLE used to accomplish this is the ‘DBA‘ role. Curious as to what the DBA role is actually comprised of? Let’s find out! Open the DBA Console First make sure you’re connected to the database you want to manage security on with a privileged administrator account. Then open the View menu and select ‘DBA.’ Accessing the DBA panel ‘Create’ a Connection Click on the green ‘+’ button in the DBA panel. It will ask you to choose a previously defined SQL Developer connection. Defining a DBA connection in Oracle SQL Developer Once connected you will see a tree list of DBA features you can start interacting with. Expand the ‘Security’ Tree Node As you click on an object in the DBA panel, the ‘viewer’ will open on the right-hand-side, just like you are accustomed to seeing when clicking on a table or stored procedure. Accessing the DBA role If I’m a newly hired Oracle DBA, the first thing I might want to do is become very familiar with the DBA role. People will be asking you to grant them this role or a subset of its privileges. Once you see what the role can do, you will become VERY protective of it. My favorite 3-letter 4-letter word is ‘ANY’ and the DBA role is littered with privileges like this: ANY TABLE privs granted to DBA role So if this doesn’t freak you out, then maybe you should re-consider your career path. Or in other words, don’t be granting this role to ANYONE you don’t completely trust to take care of your database. If I’m just assigned a new database to manage, the first thing I might want to look at is just WHO has been assigned the DBA role. SQL Developer makes this easy to ascertain, just click on the ‘User Grantees’ panel. Who has the keys to your car? Making Changes to Roles and Users If you mouse-right-click on a user in the Tree, you can do individual tasks like grant a sys priv or expire an account. But, you can also use the ‘Edit User’ dialog to do a lot of work in one pass. As you click through options in these dialogs, it will build the ‘ALTER USER’ script in the SQL panel, which can then be executed or copied to the worksheet or to your .SQL file to be ran at your discretion. A Few Clicks vs a Lot of Typing These dialogs won’t make you a DBA, but if you’re pressed for time and you’re already in SQL Developer, they can sure help you make up for lost time in just a few clicks!

    Read the article

  • Launch Webcast Q&A: Oracle WebCenter Suite 11g - The Platform for the Modern User Experience

    - by howard.beader(at)oracle.com
    Did you have a chance to watch the Oracle WebCenter Suite 11g Launch Webcast yet? Andy MacMillan presented some great information on the webcast and answered quite a few of your questions in the Q&A session as well. For your reading pleasure we have captured a number of the questions and answers and they are summarized below: Question: Can you tell me what should our Portal strategy be for integrating and extending our Oracle enterprise applications? Answer: We recommend that you look at this in two steps, the first would be to ensure that you have a good understanding of our common user experience architecture. Internally our product teams at Oracle are already investing in this quite heavily today for Fusion Applications and this is driving natural convergence from a UX strategy standpoint. The second step would be to look at how best to componentize the back office applications so that the business users across your organization can take advantage of these -- don't make it just about putting a new skin on top of what you already have from an application standpoint, instead look at how best to embed the social computing capabilities as part of the solution for your business users. Question: We are currently using the BEA WebLogic Portal now, should we stay on WLP or should we be looking at moving to WebCenter or when should we move to WebCenter? Answer: Our strategy has been called "Continue & Converge", this theme means that you can continue to use WebLogic or Plumtree portals until your organization is ready to move to WebCenter and in the mean time you can continue to deploy what you need to in your organization of WLP or WCI Portals with the full support of Oracle. In addition WebCenter Services can be leveraged for social computing to complement what you are already doing today and enable your organization to take advantage of some of the latest and greatest social computing capabilities. We have migration scripts and conversion capabilities available as well as programs where Oracle can help you evaluate your options to decide how best to move forward. WebCenter provides the best of the best capabilities and will enable you to take advantage of new capabilities that may not exist in your current portal today. In the end though it's up to you as a customer as to when you want to make the transition to Oracle WebCenter Suite. Question: Can you tell me how is Oracle leveraging WebCenter internally and for its Application and Middleware product UX strategies? Answer: Internally, Oracle is leveraging WebCenter for our employees and thus far we are seeing significant updates with our users taking advantage of the business activity streams, team spaces and collaboration capabilities. From a product strategy standpoint, our product teams are taking advantage of the common user experience architecture and leveraging WebCenter to provide social and collaborative capabilities to the Oracle Applications and providing new types of composite applications with what is coming with Fusion Applications. WebCenter also provides a common user experience across all the products in the Oracle Fusion Middleware family as well. Question: Our organization is currently using SharePoint, but we are also an Oracle Applications customer, how should we be thinking about WebCenter as we move forward? Answer: Great question. Typically, we are seeing organizations using SharePoint for its core use cases of small team collaboration and file server replacement. WebCenter can connect to SharePoint as a content source to feed into WebCenter quite easily and it leverages the robust Oracle ECM product under WebCenter as well. In addition, SharePoint team sites can be connected to WebCenter utilizing our SharePoint connector. With Oracle WebCenter though, we are really targeting business users and enterprise applications, thus affecting positive change on the processes that drive the business to improve productivity across your organization. Question: Are organizations today using WebCenter as a Web platform for externally facing public websites? Answer: Yes, we are seeing a convergence around web content management and portal types of websites with customers converting them from just broadcasting content to making it a much richer personalized experience and also exposing back-office applications as well. Web Content Management capabilities are already embedded in WebCenter so that organizations can take advantage now of the benefits a personalized web experience provides for your customers. This is simply a short summary of a few of the questions addressed on the webcast, please tune in now to learn more about Oracle WebCenter, the user experience platform for the enterprise and the web! The Oracle WebCenter Suite 11g Launch Webcast can be found here

    Read the article

  • Cox Communications' Strategic Approach to Enterprise User Experience: How Change Management and Usab

    - by Applications User Experience
    Author: Anna Wichansky, Senior Director, Applications User Experience, and Chair, Oracle Usability Advisory Board As part of our work in the User Experience group, our teams often go to Customer events such as the Higher Education User Group (HEUG) conference, Alliance 2010. This year's event was held in San Antonio, Texas, and was attended by hundreds of higher education, government, and public sector users of Oracle applications. The User Assistance team used this opportunity to reach out to customers in the Educational and Government sectors to better understand how their organizations are currently approaching help, messages, and other forms of user assistance. What is User Assistance? For us, user assistance is more than the old books of users' manuals and documentation. User assistance is anything that helps users get their jobs done quickly and efficiently. Instead of expecting users to stop and look through a guide or manual, we have been developing solutions that are embedded within the interface. We know that when people are having difficulty with a task, they want to be able to search efficiently for solutions and collaborate with coworkers. We know that they want to find their answers right there, right then, so that they can get on with their work. In our interviews at Alliance, we wanted to learn what the participants could tell us about what was happening on their campuses and in their institutions. Figure 1. For Oracle User Assistance, it's not just about books any more. So what did we do? Off to Texas, we recruited 10 people from nine different government and education organizations to come to our Oracle User Experience Onsite Usability Labs. We conducted one-hour interviews with these folks and asked them all about User Assistance--what people are doing, what they would like to do, what technologies they are using, what they would like to use, and ultimately what should we as a company be planning for our future products. We used this as an opportunity also to show them some of our design concepts for Fusion User Assistance, our next generation of user assistance based on the best of our user assistance in other products. Figure 2. Interviewing a technical user at Alliance. What we learned... People are not using paper or online manuals anymore. They don't want to see a manual that is written for technical users and that doesn't make sense to the ordinary end user. They really don't want to have to flip through a manual trying to find an answer to their question. Even when the answer might be tailored to their organization, they don't want to dig through documentation. When they need an answer now, they don't have the patience to dig for something that might or might not be clearly written. What does it mean to an organization when users don't want to deal with documentation? In many cases, it means that frustrated users make phone calls to try to find the answers that they need immediately. Phone calls are expensive to an organization and frustrating to the technical support staff who have provided documentation that no one wants to read anymore. If they don't call, they email for help often, and many users are asking for the same information. The bottom line is that if they could get that help immediately in the interface, they wouldn't have to make those calls or send those emails -- and that saves time and money. Our Fusion User Assistance options to customize help and get help for the task immediately were seen as an opportunity by these technical users to build the solutions that their users need and want. Figure 3. Joyce Ohgi and Laurie Pattison of Applications UX. Chicken Fried Steak. That was huge. But then, this was Texas, where we discovered a lot of things come very big. Drinks are served in quart-size glasses and dishes like Chicken Fried Steaks are served on platters not plates. We saw three-pound cinnamon rolls that you down with tea sweet enough to curl your hair. Deep in the heart of Texas, we learned a lot, and we ate even more.

    Read the article

  • What is the technical reason that so many social media sites don't allow you to edit your text?

    - by Edward Tanguay
    A common complaint I hear about Facebook, Twitter, Ning and other social sites is that once a comment or post is made, it can't be edited. I think this goes against one of the key goals of user experience: giving the user agency, or the ability to control what he does in the software. Even on Stackexchange sites, you can only edit the comments for a certain amount of time. Is the inability for so many web apps to not allow users to edit their writing a technical shortcoming or a "feature by design"?

    Read the article

  • iOS User guidelines at startup

    - by user963737
    I was wondering is there a way to give the user a small guided tour of the app with small pops exactly above the UI elements indicating what it will do and not using the standard popups which iOS has. Something like if an icon is used to post status there should be a small pop up on top of it which tells us it is used to post status and can be closed a standard in in games to introduce the player to their UI.

    Read the article

  • Changing the interface language in Windows 7 Home Premium

    - by Cristián Romo
    A friend of mine has recently purchased a laptop in the U.S. that has Windows 7 Home Premium on it with an English interface. Not being a native English speaker, I'm trying to change the interface language to traditional Chinese. I've looked through the Control Panel in search of something that might let me change the interface language. Naturally, I looked at the Region and Language section and managed to change the formats the computer uses and install a working keyboard, but I haven't found a way to change the interface language. Upon doing some research, I found out that there are two kinds of interface packs, Multilingual User Interface (MUI) and Language Interface Packs (LIP). It seems that MUIs can only be installed through Windows Update, so I looked through the list of updates. To my dismay, the language packs are not present. The optional updates tab doesn't even show up. Many sites show a drop down menu the under Keyboards and Languages tab in the Region and Language options, yet it doesn't show up for me. We also don't have the Windows 7 DVD which might contain this useful file. As far as the LIPs go, I can't find one in Chinese at all, let alone traditional Chinese. Can the interface language be changed in Home Premium at all? If it can, how would I do so?

    Read the article

  • How to change I/O priority of a process or thread in Win7?

    - by romkyns
    Process Explorer is able to show the effective IO priority of a given thread, but not change it. Seeing as IO priority support is a comparatively new feature, most programs don't set their own IO priorities. It appears that by default the IO priority is derived from the thread priority (rather than process priority), which Process Explorer can't modify either. Are there any other tools out there that can help me change the IO priority of a given thread / all threads of a given process?

    Read the article

  • Corliss Expert Group Home Security: How to Secure Your Home without Spending Too Much?

    - by Mika Esmond
    HOME SECURITY: HOW TO SECURE YOUR HOME WITHOUT SPENDING TOO MUCH Imagine if there were no burglar or criminals who threaten the safety of our homes; we will be surprised how much savings we would have on several things we do to secure ourselves and our loved ones. We would not need fences, gates with locks, doors locks, window grills, CCTV cams, perimeter lighting, shotguns and baseball bats. The cost of maintaining these things can run up to the entire cost of building another room or, in some cases, a whole new house. The rationale for home security is the same for national security. A nation maintains an army whether it has enemies or not; so, whether burglars will come or not, we have to prepare for the eventuality. Hence, we end up spending for something we might never put into the actual use it was intended for. You buy a pistol and when a burglar breaks in you fire the gun either to scare or disable the intruder. We hope we will never have to use these things; but we still buy them for the peace of mind that comes from knowing we can secure or protect our family and home.

    Read the article

< Previous Page | 7 8 9 10 11 12 13 14 15 16 17 18  | Next Page >