Search Results

Search found 19125 results on 765 pages for 'hard disk'.

Page 110/765 | < Previous Page | 106 107 108 109 110 111 112 113 114 115 116 117  | Next Page >

• Disk controller speed responsible for slow write speeds?

  - by vizvayu

  I have question. I'm using ESXi 4.0U1 in an IBM x3200M2 with an integrated LSI 1064e RAID controller, without any kind of cache. I have 3 250GB HOT-SWAP SATA HDs configured in RAID1E (IME). ESXi works fine, read speed are quite OK, but write speeds are incredible slow, never more than 8MB/s, and this is the best case scenario, benchmarking with iozone streaming writes, using a VMWare Paravirtual controller and with only this VM active, no swapping of any kind (total vm memory reserved). Already wrote to IBM but I don't have any kind of pay support so they didn't even answered, so I'm just wondering... anybody has any experience with a similar setup? I just want to be sure this is hardware related and can't be fixed with some kind of config option, because I'm thinking on buying a new RAID controller (Adaptec 2405 looks nice). Thanks again!

  Read the article

• mdadm: Replacing array with entirely new drives

  - by hellfur

  I have a server with three 500GB drives, with most of my data in a RAID5 configuration spanning the three of them. I just purchased and installed four 1TB drives, and the intention is to move off of the old drives and onto the new ones. I have enough SATA ports and power connectors to power all seven of my drives at once, so I've kept the old RAID running while I figure out what to do with the new drives. My question is: Should I create a whole new array on the 1TB drives, then move everything over and reconfigure linux to boot from the new md arrays? Or should I just expand the array, swapping out each of the three 500GBs with the 1TB, then adding the final drive? I've read up on the mdadm extending drive setup, and it makes sense, but I imagine I would use one of the drives as a full backup while I move things over, then add that drive back into the array once things are up and running on three of the 1TB drives, so there's some complication in going that route as well... I'm just not sure which is safer/recommended.

  Read the article

• How do I know if my disks are being hit with too much IO reads or writes or both?

  - by Mark F

  Hi All, So I know a bit about disk I/O and bottlenecks relating to this especially when relating to databases. But how do I really know what the max IO numbers will be for my disks? What metric might be available to me for working out roughly (but needs to be a good approximation) of how much capacity (if you will) have I got left available in I/O. I've seen it before where things are bubbling along nicely and then all of a sudden, everything screams to a halt, and it ends up being an IO bound problem. Is there a better way to predict when IO is reaching its limits? This article was interesting but not giving the answer I desire. "http://serverfault.com/questions/61510/linux-how-can-i-see-whats-waiting-for-disk-io". So is my best bet surrounding just looking at 'CPU IO WAIT'? There must be a more reactive method for this? Best, M

  Read the article

• How to setup RAID partitions with parted?

  - by psycketom

  I'm going through the https://wiki.archlinux.org/index.php/RAID guide in here, but I'm stuck on Partition Tables. Since my drives are 3TB, fdisk and cfdisk won't cut it due to their 2GB limit, but they are straight forward when managing partitions - adding da or fd as types. But, there is not that straight forward guide for RAID partition setup with parted. So, how do I make Non-FS or RAID partition with parted?

  Read the article

• Do 7.2k SATA drives and a hardware raid controller always end with trouble?

  - by xelco52

  I'm reading the FreeNAS userguide and came across the statement: Note that hardware RAID configured as JBOD may still detach disks that do not respond in time; and as such may require TLER/CCTL/ERC-enabled disks to prevent drive dropouts. I'm using a '3Ware 9550SX-8LP RAID Controller' and see quite a few stories of people successfully running raid5 on 7.2k consumer SATA drives without issue. Are detached disks only a theoretical problem, or should I expect this to be a common occurrence?

  Read the article

• HDD dead forever???

  - by Roberto

  Yesterday I turned on my computer and it couldn't boot. I found out the hd (320GB SATA Seagate Momentus 7200.3 for notebook) was broken, it couldn't be recognized by the BIOS. I have another of the same hd, so I exchanged the boards. I found out that there is a problem on its board since my good hd didn't work. But the broken hd doesn't work with the good board as well: it can be recognized but when I insert a Windows Instalation DVD it says the hd is 0GB. I put it in a case and use it in another computer via USB, and but it doesn't show up in the "My Computer". I used a software to recover files called "GetDataBack for NTFS", it recognized the hd but with the wrong size (2TB). I try to make it read the hd but it get an I/O error reading sector. It tries to read, the hd spins... So, since I'm using a good board on it, the problem seems to be internal. Is there anything someone could do recover the files from it?

  Read the article

• sectors per track

  - by Phenom

  If you know the media transfer rate, how do you calculate the maximum number of sectors per track from that?

  Read the article

• number of search accesses

  - by Phenom

  How do you calculate number of accesses for a sequential search if record is present, not present, or sometimes present? What about for binary search?

  Read the article

• How do I backup (from Vista Home Premium) to a FAT32 HDD connected to a wireless router with no user account or password set?

  - by Scubadooper

  I have a Seagate expansion 2TB HDD which I've managed to get working on my wireless router (thanks to fat32format) however I haven't managed to set my backup to work with it. Vist Home Premium requires that I input a username and password in the backup utility. As far as I'm aware that type of access control isn't set on the HDD: Can I set up the access control on the HDD? If so how Or, can I set the backup to work without it? If so how Thanks for your help, I haven't been able to find the answer anywhere on the net so far

  Read the article

• How to make RHEL have persistent local hdd name?

  - by Mxx

  I have 2 identical Dell R720 servers running identical Oracle Enterprise Linux(RHEL)6.4. Both servers (supposedly) configured in exactly the same way. However, one of the servers is behaving differently. Every other reboot its local HDD name(and related partitions) flip from /dev/sda to /dev/sdj. This is problematic because both servers are configured for multipathd, and if this flip happens their config does not match and Oracle DB(or its clusterware) complains that nodes are not configured identically. Why does one server has a consistent device names while the other server keeps flipping back and forth? How can I make local hdd to consistently be /dev/sda? I suspect this might have something to do with udev but I'm not sure.

  Read the article

• Failing Seagate HDD - Not Recognised

  - by thefragileomen

  I am having a look at a friend's computer which contains a 500GB Seagate HDD. Unfortunately the HDD is not recognised by the BIOS menu and it beeps 11 times upon powerup. I've moved the HDD to another laptop but the problem remains. I've downloaded SeaTools for DOS (Seagate's Diagnostic tool) but unfortunately to no avail and the disc remains unseen when using this DOS boot disc. The HDD is only 6 months old so I'm very surprised at this but it appears a common problem with Seagate 2.5" HDDs as well as other HDDs manufactured by Seagate. I intend to try it in an external caddy on Thursday when back in work and also through a forensic writeblocker but just wondering if anyone has any other suggestions? I am of the opinion it is some chip on the HDD board which prevents it spinning due to a fault. If so, I've lost to deactivate this just so I can simply recover the data on the drive and start with a new disc. Thanks

  Read the article

• Hooking up many different external HDs simultaneously

  - by cbizz

  I need a large amount of external storage for an upcoming project. I'm planning on purchasing 10 2TB external drives. I need them all hooked up to a single machine at the same time. What issues will I run into? I plan on using 2 power strips and having them all externally powered from the wall. I will use a USB hub to plug in all the drives. I need drive access time to be as fast as possible. I am using Ubuntu Linux(64 bit). Will I be able to mount 10 drives?

  Read the article

• Extensive use of HDD after VmWare Player virtual machine is closed.

  - by Bobrovsky

  Each time I close virtual machine in VmWare Player I see extensive use of HDD in my system. Basically, whole system becomes unresponsive for about 5-7 minutes. Host system is Windows 7 Utimate x64 SP1 with 6 GB of memory, i3-M350 processor. Virtual machine is Windows XP SP3 x86 (2GB of memory allocated for VM). What can be the cause and what can I do to solve the issue? UPDATE: I am not shutting down the VM, I just close Player window and VM saves it's state. System becomes unresponsive right after VM have saved it state (as indicated by Player) and Player itself have closed.

  Read the article

• Asus ux31e zenbook SSD non-standard / cant upgrade hdd?

  - by FstaRocka

  I bought a ux31e asus zenbook, and the drive crashed last week. I just cancelled an mSata ssd order because I fear asus has used a non standard ssd!!! what a bunch of crooks, ive lost all my respect for this company! Can anyone confirm what and why? My SSD model is xm11 128gb - it looks like a ram chip and only has two tongues with 12 and 6 pins respectively. The drive I was about to order mSata had 8 where mine had 6 - i never bothered counting the rest. This article seems to confirm! UX31 UX21 Zenbook Article "It looks like SSD uses a non-standard format"

  Read the article

• Can I mix drive types in an HP server?

  - by Generic Error

  I currently have the following setup: HP DL380 G4 Server 6 x 73GB, Ultra160, 10k, SCSI 80 Pin Drives Smart Array 6i Controller RAID 5 One of the drives is failing and needs to be replaced. I have on hand drives that are the same size and type, but are Ultra320, 15k instead. I have verified that these drives work in another system with the same type of drive controller. When I plug one of these in the system simply reports the drive as being offline and has nothing further to do with it. From what I have read these drives should be compatable. Should this work at all and if so, what might be preventing it?

  Read the article

• Boost Up My Old Laptop Using a SSD

  - by Sina Bizbone

  I have an old laptop Lenovo SL400 (Core2Due T9550 2.66GHz / 4GB DDR2 Ram). Since I can't afford to buy a new laptop, I thought maybe I could throw an ADATA SP600 64GB SSD as primary drive and move my current HDD to DVD-ROM space by using HDDCADDY. I know that 64gb will come short after installing Visual Studio, SQL Server, etc. So is there anyway to just install the kernel part of windows on SSD and the rest on HDD. Doesn't windows have built-in support to do this? (ReadyBoost is out of picture since it's just simple caching)

  Read the article

• Debian on HP ProLiant server hangs (disk i/o is my guess)

  - by Martin

  I installed Debian (2.6.32-5-amd64) on my HP ProLiant MicroServer (purchased recently.) I also added 3 2tb hd in zfs. I've experienced several server froze. Sometimes it showed Soft lockup CUP stuck for 61s! Today I experienced a different problem (I think) and the message looked like this [431336.200002] Call Trace: [431336.200002] [<ffffffff812fcc7c>] ? _write_lock+0xe/0xf [431336.200002] [<ffffffff810d7a86>] ? __vmalloc_node+0x99/0xe2 : : and (in different screen) [431354.222318] Node 0 DMA32 free: 2064kB min:5520kB low:69900kB high:8280kB active_anon:181648kB inactive_anon:61728kB active_file:313152kB inactive_file:832456kB unevictable: 0kB isolated(anon): 0kB isolated(file):0kB present:1922596kB mlocked:0kB dirty:72kB writeback:0kB mapped:25620kB shmem:344kB slab_reclaimable:34460kB slab_unreclaimable:31400kB kernel_stack:2288kB pagetables:7556kB unstable:0kB bounce:0kB writeback_tmp:0kB pages_scanned:0 all_unreclaimable? no [431354.222431] lowmem_reserve[]: 0 0 0 0 : : Is this a hardware problem? What tools/methods can I find out the source of the problem? I've used Debian for years but never had problem like this.

  Read the article

• External HDD connecting via USB disconnects wireless LAN connection

  - by Kensai

  Strange problem. I have this MEDION Akoya PC that has a dedicated bay to slide an external HDD sold separately. It's very handy indeed cause the slot is providing a fast USB 3 connection and power to the HDD unit, without extra cables. All works fine except this show-stopper behavior to disconnect me from the router once I slide in the unit and it powers up. The moment I connect the unit the (normally) three-four WiFi connections I see in my neighborhood disappear and my own to the router loses its signal strength (no Internet traffic is possible). After a while it throws me off that one as well, never to connect me again as long as the unit is powered. Once I disconnect the HDD the various signals come back and it automatically reconnects to my own. What takes? Are we in front of a serious design fault by MEDION here? Does the spinning of the HDD on top of the PC cause electromagnetic interference strong enough to throw off my WiFi connectivity? Is it a simple USB problem? Some kind of strange hardware conflict? Where should I look?

  Read the article

• What is the best SSD deal available right now ?

  - by paulgreg

  What is the best 2.5" SSD deal (best performance for a reasonable price and a good size) available right now ? The question is in 'community wiki' mode, so feel free to post the "winner" below : And the winner is... : currently the OCZ Vertex. Prices: * 30GB - $149.99 * 60GB - $239.99 * 120GB - $389.00 * 250GB - $829.00 Speed: * Read: up to 270MBps * Write: up to 210MBps

  Read the article

• Question about getting information off an old HD...

  - by user37983

  Ok so my old cpu was a sony vaio. its kinda old and had xp on it. My gf thrashed it - the cd drive went and she tried fixing it by messing with the configurations bios etc. the actual laptop is really fried the keyboard doesnt work, etc. However the harddrive is still intact. I tried putting the HD in my new cpu (toshiba runnig win7) and it looks like its gonna boot up it goes to the screen with the logo and the status bar starts to load. then it flashes a blue screen for a split second, and goes to the black screen where it says windows did not shut down properly and gives options to (start windows normally, safe mode, safe mode with networking, safe mode with prompts) ive tried every option but it always goes back to this screen. I need to get into the hd cuz i have very important files. is there anyway?

  Read the article

• Is a 1TB drive too big for a boot drive?

  - by CT

  Can the drive you choose to boot off affect performance? Would I receive faster boot/shutdown times if I were to choose a smaller drive? How would partitions affect performance/boot speed? Assuming all drives are the same RPM, lets say 7200.

  Read the article

• Safest snapshot of a failing harddrive?

  - by ironfroggy

  I have a headless machine that stopped booting, so I pulled it out for diagnostics and got a message that one of the harddrives was about to fail, so I pulled them all out and I need to get everything off, before figuring out which I need to get rid of. I wasn't sure which drive was failing, because it only said "Harddrive 1" and I don't know which it referred to. I'm wondering the best way to get everything off. I'm worried if I copy everything, I could get corrupt data and not realize some files are wrong until the drive is completely out of commission. What are my best options to get everything off in a way I can safely move to new storage?

  Read the article

• Why do SSD drives get so much more expensive as they get larger?

  - by futuraprime

  Normal HDD costs go up very little as drives get larger. For example, an average 1TB drive costs a little under $90, 2TB costs a little over $100, and a 3TB drive costs close to $150. For HDDs, the cost per GB goes down as the number of GB goes up. SSD costs don't work like this: a 128GB SSD goes for $120ish, 256GB goes for $250ish, and 512GB drives get up to $600. The cost per GB goes up as the number of GB rises. What is it about SSDs that makes them so much costlier as they get larger?

  Read the article

• maximum number of sectors per track

  - by Phenom

  If you know the media transfer rate, how do you calculate the maximum number of sectors per track?

  Read the article

• Install windows xp using USB: removable disk option not available in boot device options list

  - by kowsar89

  I want to install windows xp with pendrive as my dvdrom doesnt work. When i go to bios setup and boot device options,i cant find any option for pendrive.Here's my boot device options: >1st FLOPPY DRIVE >3M-HDS728080PLA >PS-ASUS DVD-E818A >DISABLED And Here's my desktop configuration: intel(R) pentium(R) 4 CPU 2.66GHz 0.99GB RAM N.B: I bought my desktop in 2006. Now how can i install windows xp in my desktop using pendrive?

  Read the article

< Previous Page | 106 107 108 109 110 111 112 113 114 115 116 117  | Next Page >