Search Results

Search found 9398 results on 376 pages for 'matt dev'.

Page 110/376 | < Previous Page | 106 107 108 109 110 111 112 113 114 115 116 117 | Next Page >

Wireless AP Placement and Digramming

- by Matt Simmons

I'm trying to research the best placement of wireless APs in a given space, and I'm running into problems in gathering information. I found (what I thought was) a great source in this tech republic article: http://techrepublic.com.com/5206-6230-0.html?forumID=82&threadID=163120 While this diagram seems detailed and overall very informative, there were a lot of comments talking about how it was lacking in things like "wire racks, microwaves, concrete walls, motors..." etc. Maybe I'm rash, but I just sort of looked around my office (which is, albeit, somewhat smaller than the one diagrammed), and went "uhhh, there", and hooked up the AP. It seems to cover everywhere. I imagine if my office quadrupled in size, I'd logically divide it up and put four APs in, with a similar amount of thought devoted to each. So, suppose I had a much more complex office. What tools (both diagramming and surveying) do you use to plan your AP placement?

Read the article
HP ProCurve GVRP Setup

- by Matt

I'm trying to setup GVRP on my 4 ProCurve switches. Currently I have a Layer 3 3500yl-24G (J8692A) which is connected to 3 Layer 2 2510G-48 (J9280A). I have three trunk ports setup on the 3500 connected to the 3 switches and currently everything seems to be working, the devices are talking to eachother and GVRP is pushing its configurations from the 3500 to the 3 other switches. My question is, once GVRP is setup, how exactly do I configure the ports on the 3 L2 switches to use the correct VLAN? I'm new to ProCurve network equipment and this is much easier to setup on Cisco equipment.

Read the article
Windows 7 Default Gateway problem

- by Matt

Hi, I have a strange problem (or at least seems strange to me) the below are IP configurations for two laptops on my home network which consists of a main router 192.168.11.1 and a connected wireless router (i know this can cause problems but has always worked until I got the win7 machine) at 192.168.11.2 with DHCP disabled. Laptop 1 - Win XP IP: Dynamically assigned by main router default gateway: 192.168.11.1 (main router) This machine gets perfect connectivity. Laptop 2 - Win7 IP: dynamically assigned by main router Default Gateway: 192.168.11.2 THIS IS THE PROBLEM... I cannot seem to get this machine to default to the main router for the gateway UNLESS I go to a static configuration which I would rather not do since I regularly go between my home and public networks. Why is my Win7 machine not finding the main gateway the same way that the other laptop is? I believe that the rest of my setup is fine as it has always worked and it works perfectly when set as static ip and gateway. Please help! Thanks

Read the article
Vim: change the quick fix title

- by romeovs

I'm using following makeprg to get my tex files compiled in vim: setlocal makeprg=pdflatex\ \-file\-line\-error\ \-shell\-escape\ \-interaction=nonstopmode\ $*\\\|\ tee\ \/dev\/tty\ \\\|\ grep\ \-P\ ':\\d{1,5}:\ ' which yields great results (errors displayed properly, tex compilation shown while busy,...) Yet, when there are errors and the quickfix window pops up, its status bar is cluttered up with the makeprg string: pdflatex\ \-file\-line\-error\ \-shell\-escape\ \-interaction=nonstopmode\ $*\\\|\ tee\ \/dev\/tty\ \\\|\ grep\ \-P\ ':\\d{1,5}:\ ' Is there a way of changing the quickfix title/statusbar?

Read the article
Anyone have experience with Silicon Mechanics 4-Node Machines?

- by Matt Simmons

I'm taking a look at buying some new servers (small infrastructure, 2 racks, etc), and although I like a lot of the features in blades, I'm looking at the price point for Silicon Mechanics' 4-node machines. http://www.siliconmechanics.com/i27091/xeon-2U-4-Node.php It's a bit like a mini-blade enclosure, but has no shared resources, except for the redundant power supplies. A single point of management would be great, but for the low price point here, I'm possibly willing to give that up, if the server quality is adequate. Basically, have you used these machines? Any problems? Anything you like?

Read the article
problem when view the super block in ext3 file system

- by xuczhang

I tried to view the superblock by command "dd" in ext3 file system. dd if=/dev/sda3 bs=4096 skip=1 count=1 of=superblock But the result in superblock file is not correct(I compare the value of Inodes count I got from dumpe2fs). The device file /dev/sda3 is started at the boot block and then the superblock of the group0? And another question is the boot block and superblock's size are both BLOCKSIZE(here is 4096)? The disk format of ext2/ext3(I think they are the same) are shown below:

Read the article
Can ISC dhcpd operate as a proxy dhcp server for PXE boot?

- by Matt

I have an existing LAN with a DHCP server already dishing out IP addresses. For various reasons I cannot replace that server so it will still need to dish out IP addresses. I've been experimenting with dnsmasq in proxy mode to provide PXE boot filenames. Now I have dnsmasq chainloading iPXE ok, but I found that the problem with dnsmasq is that in proxy mode it won't send dhcp options down. So I can't seem to send option 17 to boot iscsi san. I read somewhere that it's not enabled in the source code. Oh well, so I thought perhaps I should try isc dhcpd (default version4 with ubuntu). But I can't find any configuration examples that work as a proxy. Does isc dhcpd even work in proxy mode? examples on the web imply patching the source. What other options do I have?

Read the article
How to configure Hyper-V failover cluster to live migrate when dynamic memory runs out?

- by Matt Johnson

Appologies in advance that this is not a direct programming question, but I have a feeling that the solution involves custom powershell scripts (maybe), so this is as good a place to ask as any. I maintain a website that has a large Hyper-V cluster for SQL Servers. We are using Windows 2008 R2 SP1, and the new "dynamic memory" feature. I've already ready reviewed the Best Practices Guide, and implemented it's suggested configuration. Everything works well, except that when SQL demand increases memory pressure to expand to more memory than is available on the physical machine, the memory status goes into the "Warning" state and stays there. I assume the hypervisor is using a swapfile on the host to fulfill the memory requirement, thus slowing the virtual machine down. When this happens, there are plenty of other nodes in the cluster that have available resources. I can live-migrate the virtual server over there and everything works, and the warnings go away. Now how can I automate this? I see no menu options in either Hyper-V or the Failover Cluster Manager for performing a migration or shutdown when dynamic memory goes into the warning state. Any ideas about how to script this, or monitor it and invoke the action directly, would be helpful. If the solution involves coding, powershell would be ideal, but I could envison this as a .Net Service that monitors for this state and kicks off the migration request. I just don't know what objects are involved in doing the monitoring or kicking off the live migration. Thanks in advance.

Read the article
Apache mpm-itk Performance

- by Matt Beckman

I manage a bunch of VPSs with memory ranging from 1GB to 8GB. Most of these websites are Joomla websites, and the servers must support multiple sites/users/S-FTP. I use mpm-itk almost exclusively (mostly due to it's convenience in these shared environments). However, I'm aware it isn't known for performance, so I need some advice on making it faster. Due to the lack of documentation when I first went the way of mpm-itk, I included only one setting in the config, and that was to limit each user to 50 clients (the rest I left up to defaults): <IfModule mpm_itk_module> MaxClientsVHost 50 </IfModule> Are there any better alternatives available? Are there any settings supported in mpm-prefork or mpm-worker that are also supported in mpm-itk? Thanks!

Read the article
creating a new user Ubuntu

- by Matt

I am trying to new user that can sftp on a server....i did this ubuntu@ip-10-112-46-15:~$ sudo useradd jesse -p testPass ubuntu@ip-10-112-46-15:~$ sudo passwd jesse Enter new UNIX password: Retype new UNIX password: passwd: password updated successfully but when i try to login via sftp I cant get in....am i missing something like adding a group or something the answer was PasswordAuthentication yes

Read the article
Microsoft Remote Desktop Services - Android

- by Matt Rogers

We have recently started testing Remote Desktop Services. We have deployed the environment using the latest server, Windows Server 2012 R2. We have deployed the Web Access Roles, RD Gateway, Connection Broker Virtualization Host and Session Host. We are running both, Virtual machine-based and Session-based deployments. All of these are working as expected internally and externally when using a Windows workstation as the RDS client, however, the Android client is unable to launch applications. Once you install the app from Google Play you are given a screen to add Remote Resources. After entering the appropriate URL, username and password we see the applications that have been published. Unfortunately, when we attempt to launch an app we get the following error: Connection Error Host not found. Please provide the fully-qualified name or the IP address of the host. We have already entered this information otherwise I don't believe we would be able to see the published applications. I think the error is related to the certificate and how it is being used to connect to the applications. Since this is in our lab environment we have not configured a valid external certificate on the servers and the trusted certificate that is installed on the android tablet points to our internal server / domain name. What I would like to know: Has anyone configured RDS Web Access on Server 2012 R2 and attempted to externally connect an Android or iOS device using the Microsoft supported Remote Desktop client. Are others experiencing the same problem we are? Were you able to resolve the issue? Was it related to the external cert / host name?

Read the article
Short POST data in HTTP

- by Matt

We're hosting a customer's Debian Linux web server. It's running a PHP based web application. The server is sitting behind our firewall with it's own virtual interface and port 80 is forwarded internally to a machine sitting in the DMZ. The issue we're having is that when data is posted to the server it seems to be being cut short for some users. It's reproducable for some users on the same box. But the same user sending the same data on the same lan on another PC it works. The data gets cut to around 1140 bytes I'm told. Any idea why this might be happening? The customer is blaming our firewall, but then surely we'd have issues with other services. I'm suspecting it's a problem with the website itself. Suggestions on how to isolate the problem would be of help. Our firewall is Astaro. EDIT: A customer has set the ethernet frame size temporarily to 500bytes on the server. This made it work for now! I know some of the customers are using an internet provider that runs PPPoE

Read the article
Outlook 2007 OST File Indexing and OneNote 2007 Indexing are Broken

- by Matt

I'm running Outlook 2007 under Windows 7 Home Premium RTM. My OST file was previously being properly indexed but eventually searches significantly slowed down so I suspected a problem. Searching and indexing appears broken in OneNote 2007 as well as search time is now significantly longer. I brought up the Outlook 2007 Search Options dialog and noticed that my mailbox (running from an Exchange 2007 server) wasn't listed in the "Index messages in these data files:" list box. Next I ran the Windows "Find and fix problem with windows search" wizard which reported no errors. Then I brought up the Windows Indexing Options dialog which shows Outlook listed (as shown here): then clicked Advanced and Rebuilt the index. No dice - the listbox in the Outlook 2007 dialog still didn't show my mailbox. When I clicked the Modify button in the Indexing Options dialog I see the following: When I hover over the "oneindex://..." entry, the alt text indicates "This location is currently unavailable". When I delete it and rebuild the index, this entry returns. UPDATE: Comparison of the last screenshot above with a working PC shows that on the broken PC, the lower half of the dialog lists Outlook but neither Outlook or OneNote are showing in the upper half. The working PC has Outlook and OneNote in both parts of the dialog.

Read the article
iptables (NAT/PAT) setup for SSH & Samba

- by IanVaughan

I need to access a Linux box via SSH & Samba that is hidden/connected behind another one. Setup :- A switch B C |----| |---| |----| |----| |eth0|----| |----|eth0| | | |----| |---| |eth1|----|eth1| |----| |----| Eg, SSH/Samba from A to C How does one go about this? I was thinking that it cannot be done via IP alone? Or can it? Could B say "hi on eth0, if your looking for 192.168.0.2, its here on eth1"? Is this NAT? This is a large private network, so what about if another PC has that IP?! More likely it would be PAT? A would say "hi 192.168.109.15:1234" B would say "hi on eth0, traffic for port 1234 goes on here eth1" How could that be done? And would the SSH/Samba demons see the correct packet header info and work?? IP info :- A - eth0 - 192.168.109.2 B - eth0 - B1 = 192.168.109.15 B2 = 172.24.40.130 - eth1 - 192.168.0.1 C - eth1 - 192.168.0.2 A, B & C are RHEL (RedHat) But Windows computers can be connected to the switch. I configured the 192.168.0.* IPs, they are changeable. Update after response from Eddie Few problems (and Machines' B IP is different!) From A :- ssh 172.24.40.130 works ok, (can get to B2) but ssh 172.24.40.130 -p 2022 -vv times out with :- OpenSSH_4.3p2, OpenSSL 0.9.8e-fips-rhel5 01 Jul 2008 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 debug1: Connecting to 172.24.40.130 [172.24.40.130] port 2022. ...wait ages... debug1: connect to address 172.24.40.130 port 2022: Connection timed out ssh: connect to host 172.24.40.130 port 2022: Connection timed out From B2 :- $ service iptables status Table: filter Chain INPUT (policy ACCEPT) num target prot opt source destination Chain FORWARD (policy ACCEPT) num target prot opt source destination 1 ACCEPT tcp -- 0.0.0.0/0 192.168.0.2 tcp dpt:22 Chain OUTPUT (policy ACCEPT) num target prot opt source destination Table: nat Chain PREROUTING (policy ACCEPT) num target prot opt source destination 1 DNAT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:2022 to:192.168.0.2:22 Chain POSTROUTING (policy ACCEPT) num target prot opt source destination Chain OUTPUT (policy ACCEPT) num target prot opt source destination And ssh from B2 to C works fine :- $ ssh 192.168.0.2 Route info :- $ route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.0.0 * 255.255.255.0 U 0 0 0 eth1 172.24.40.0 * 255.255.255.0 U 0 0 0 eth0 169.254.0.0 * 255.255.0.0 U 0 0 0 eth1 default 172.24.40.1 0.0.0.0 UG 0 0 0 eth0 $ ip route 192.168.0.0/24 dev eth1 proto kernel scope link src 192.168.0.1 172.24.40.0/24 dev eth0 proto kernel scope link src 172.24.40.130 169.254.0.0/16 dev eth1 scope link default via 172.24.40.1 dev eth0 So I just dont know why the port forward doesnt work from A to B2?

Read the article
Windows Server 2008 Create Symbolic Link, updated Security Policy still gives privilege error

- by Matt

Windows Server 2008, RC2. I am trying to create a symbolic/soft link using the mklink command: mklink /D LinkName TargetDir e.g. c:\temp\>mklink /D foo bar This works fine if I run the command line as Administrator. However, I need it to work for regular users as well, because ultimately I need another program (executing as a user) to be able to do this. So, I updated the Local Security Policy via secpol.msc. Under "Local Policies" "User Rights Management" "Create symbolic links", I added "Users" to the security setting. I rebooted the machine. It still didn't work. So I added "Everyone" to the policy. Rebooted. And STILL it didn't work. What on earth am I doing wrong here? I think my user is even an Administrator on this box, and running plain command line even with this updated policy in place still gives me: You do not have sufficient privilege to perform this operation.

Read the article
virsh XML interface allocation

- by Kaushik Koneru

I am trying to launch VM using a XML. This VM will be having 5 interfaces each connected to certain bridge. Issue here is allocation of these interfaces is random. My XML <interface type='bridge'> <mac address='52:54:00:9f:14:b3'/> <source bridge='br0'/> <target dev='vnet1'/> <model type='e1000'/> <alias name='net0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/> </interface> <interface type='bridge'> <mac address='52:54:00:9f:14:b4'/> <source bridge='br1'/> <target dev='vnet2'/> <model type='e1000'/> <alias name='net1'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x10' function='0x0'/> </interface> <interface type='bridge'> <mac address='52:54:00:9f:14:b5'/> <source bridge='br2'/> <target dev='vnet2'/> <model type='e1000'/> <alias name='net3'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x12' function='0x0'/> </interface> <interface type='bridge'> <mac address='52:54:00:9f:14:c4'/> <source bridge='br3'/> <target dev='vnet3'/> <model type='e1000'/> <alias name='net4'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x18' function='0x0'/> </interface> Allocation of interfaces are random mean e th6 will be connected to br3 ; eth7 -- br4 eth8 -- br2 eth9 -- br0. Is there any way to make it static?? At the same time is there anyway of assigning IP Address to these eth interfaces through XML file itself??

Read the article
Virtualhost pulling from the same site??

- by Matt

I have my httpd.conf on fedora 8 that I am setting the virtual host file. Here is what I have: DocumentRoot "/var/www/html" <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory "/var/www/html"> Options Indexes FollowSymLinks AllowOverride All Order allow,deny Allow from all </Directory> then below I am trying to setup a vhost to have multiple sites on the server: NameVirtualHost *:80 <VirtualHost *:80> ServerName kadence.tv DocumentRoot /var/www/html/ </VirtualHost> <VirtualHost *:80> ServerName nacc.biz DocumentRoot /var/www/html/nacc/ </VirtualHost> also in the /var/www/html/ directory I have the index.php file for the kadence site...when I do to either site I get the index for the kadence site...any ideas what I am doing wrong EDIT the full contents of my httpd configuration file are here.

Read the article
Can't access Linux machine from the network, network from the machine is fine

- by Matt

I'm having issues with a machine that stopped replicating with mysql. It's managed by a guy on another continent but recently I've had to get involved. The server is running Ubuntu server 9.10 I can't log in with SSH, there is no response. On the server itself I can ssh to localhost fine. I thought maybe it's the firewall rules. I'm no expert on IP Tables, but I believe that's not the issue as I removed all the rules. But it still won't let me in. Any ideas? it's acting from other machines as though the service isn't listening, but I know that it is. It's like this for all services.

Read the article
Restrict VPN user to Remote Desktop only with Sonicwall

- by Matt

Basically I want him to only be able to log onto the VPN in order to use Remote Desktop to use HIS machine. Not surf the internet or do anything like that, but just use the programs on his machine that he doesn't have at home. We use a Sonicwall NSA 220 with their regular VPN client. I can create a user for him, but when I create an access rule it applies to all VPN users. How can I make something like that only apply to ONE user?

Read the article
How to see the olddir after mount --bind olddir newdir?

- by freestyler

In my debian 7: $ pwd /home/freestyler $ mkdir old new # mount --bind old new then $ mount /dev/cciss/c0d0p9 on /home/freestyler/new type ext4(rw,noatime,nodiratime,user_xattr,barrier=1,data=ordered) I can only see the /dev/cciss/c0d0p9, which is not the same as /home/freestyler/old How can I get the original olddir path? In debian 6: the mount outpt the olddir path well: $ mount /home/freestyler/old on /home/freestyler/new type none (rw,bind)

Read the article
How could two processes bind onto the same port?

- by Matt Ball

I just ran into an issue where a request made to localhost:8080 from curl was hitting a different server than the same request made from inside Node. lsof -i :8080 revealed that two processes were both binding onto the same port: COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME node 51961 mball 14u IPv4 0xd980e0df7f175e13 0t0 TCP *:http-alt (LISTEN) java 62704 mball 320u IPv6 0xd980e0df7fe08643 0t0 TCP *:http-alt (LISTEN) How is this possible? Were they binding onto different interfaces? Or was it the IPv4 vs 6? If you're curious, node was hitting the other node process, curl was hitting the java process. The java process was started after the node process.

Read the article
Connectivity issues with dual NIC machine in EC2

- by Matt Sieker

I'm trying to get some servers set up in EC2 in a Virtual Private Cloud. To do this, I have two subnets: 10.0.42.0/24 - Public subnet 10.0.83.0/24 - Private subnet To bridge these two, I have a Funtoo instance with a pair of NICs: eth0 10.0.42.10 eth1 10.0.83.10 Which has the following routing table: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.0.83.0 * 255.255.255.0 U 0 0 0 eth1 10.0.83.0 * 255.255.255.0 U 203 0 0 eth1 10.0.42.0 * 255.255.255.0 U 202 0 0 eth0 loopback * 255.0.0.0 U 0 0 0 lo default 10.0.42.1 0.0.0.0 UG 0 0 0 eth0 default 10.0.42.1 0.0.0.0 UG 202 0 0 eth0 An elastic IP is attached to the eth0 interface, and I can connect to it fine remotely. However, I cannot ping anything in the 10.0.83.0 subnet. For now iptables is not set up on the box, so there's no rules that would get in the way (Eventually this will be managed by Shorewall, but I should get basic connectivity done first) Subnet details from the VPC interface: CIDR: 10.0.83.0/24 Destination Target 10.0.0.0/16 local 0.0.0.0/0 [ID of eth1 on NAT box] Network ACL: Default Inbound: Rule # Port (Service) Protocol Source Allow/Deny 100 ALL ALL 0.0.0.0/0 ALLOW * ALL ALL 0.0.0.0/0 DENY Outbound: Rule # Port (Service) Protocol Destination Allow/Deny 100 ALL ALL 0.0.0.0/0 ALLOW * ALL ALL 0.0.0.0/0 DENY CIDR: 10.0.83.0/24 VPC: Destination Target 10.0.0.0/16 local 0.0.0.0/0 [Internet Gateway ID] Network ACL: Default (replace) Inbound: Rule # Port (Service) Protocol Source Allow/Deny 100 ALL ALL 0.0.0.0/0 ALLOW * ALL ALL 0.0.0.0/0 DENY Outbound: Rule # Port (Service) Protocol Destination Allow/Deny 100 ALL ALL 0.0.0.0/0 ALLOW * ALL ALL 0.0.0.0/0 DENY I've been trying to work this out most of the evening, but I'm just stuck. I'm either missing something obvious, or am doing something very wrong. I would think I'd be able to ping from either interface on this box without issue. Hopefully some more pairs of eyes on this configuration will help. EDIT: I am an idiot. After I bothered to install nmap to run some more tests, I discover I can see the ports, and connect to them, pings are just being blocked.

Read the article
How do I PXE boot multiple Windows 7 desktops off the same image?

- by Matt

Some years ago in my uni days I recall that the uni labs booted windows nt over the network. There was a shared drive for your own stuff, and other than that any changes you did to the running OS were reset when you restarted the machine. Now I'd like to be able to do the same thing with Windows 7. I have found some howto's for this using iSCSI, but I don't want an iSCSI disk for every single PC, I'm wanting one image for multiple PC's. I've also found PXE Boot setups for installing windows locally, but that's not what I want either. How would I go about setting up what I had at uni but with Windows 7 as a OS to netboot? i.e. How do I netboot windows 7 images? I do not want to netboot a windows 7 installer to a pc to install windows locally, I want to run a windows 7 image from memory/network.

Read the article
Understanding vhosts settings

- by Matt

Ok so i have a server and I want to put a few applications on and i am having vhost configuration problems. Here is what i have and I want some direction on what i am doing wrong...ok so the first file is /etc/apache2/ports.conf NameVirtualHost 184.106.111.142:80 Listen 80 <IfModule mod_ssl.c> Listen 443 </IfModule> <IfModule mod_gnutls.c> Listen 443 </IfModule> then i have /etc/apache2/sites-available/somesite.com <VirtualHost 184.106.111.142:80> ServerAdmin [email protected] ServerName somesite.com ServerAlias www.somesite.com DocumentRoot /srv/www/somesite.com/ ErrorLog /srv/www/somesite.com/logs/error.log CustomLog /srv/www/somesite.com/logs/access.log combined <Directory "/srv/www/somesite.com/"> AllowOverride all Options -MultiViews </Directory> </VirtualHost> when i visit somesite.com everything works great but when i add another vhost and lets say thats named anothersite.com. So i have /etc/apache2/sites-available/anothersite.com <VirtualHost 184.106.111.142:80> ServerAdmin [email protected] ServerName anothersite.com ServerAlias www.anothersite.com DocumentRoot /srv/www/anothersite.com/ ErrorLog /srv/www/anothersite.com/logs/error.log CustomLog /srv/www/anothersite.com/logs/access.log combined <Directory "/srv/www/anothersite.com/"> AllowOverride all Options -MultiViews </Directory> </VirtualHost> then i run the following commands >> sudo a2ensite anothersite.com Enabling site anothersite.com. Run '/etc/init.d/apache2 reload' to activate new configuration! >> /etc/init.d/apache2 reload * Reloading web server config apache2 ...done. but when i visit anothersite.com or somesite.com they are both down..What is going on with the vhosts. Could it be the NameVirtualHost declaration with the ip or something...maybe my understanding of vhost settings is not clear. What i dont understand is why do both site now all the sudden not work at all.I would highly appreciate the clarity By the way anothersite.com or somesite.com are the only things I changed to make it more readable

Read the article
.NET framework error 0xc000007b

- by Matt

I'm trying to install UDK, but I get the error The application was unable to start correctly (0xc000007b). Click OK to close the application. I tried re-installing .NET Framework 4 and MSVC++ Redistributable 2010 x64 with a separate uninstaller, but I still get the same error. I have had this problem both before and after reinstalling Windows 7 x64. I think it might be because UDK is 32-bit and everything else is 64-bit, but there shouldn't be any errors with backwards compatibility. How do I fix this?

Read the article

< Previous Page | 106 107 108 109 110 111 112 113 114 115 116 117 | Next Page >