HP ProCurve GVRP Setup

Posted by Matt on Server Fault See other posts from Server Fault or by Matt
Published on 2010-05-06T15:10:33Z Indexed on 2010/05/06 15:18 UTC
Read the original article Hit count: 614

Filed under:

procurve

|

switches

|

vlan

I'm trying to setup GVRP on my 4 ProCurve switches. Currently I have a Layer 3 3500yl-24G (J8692A) which is connected to 3 Layer 2 2510G-48 (J9280A). I have three trunk ports setup on the 3500 connected to the 3 switches and currently everything seems to be working, the devices are talking to eachother and GVRP is pushing its configurations from the 3500 to the 3 other switches. My question is, once GVRP is setup, how exactly do I configure the ports on the 3 L2 switches to use the correct VLAN? I'm new to ProCurve network equipment and this is much easier to setup on Cisco equipment.

© Server Fault or respective owner

Related posts about procurve

HP ProCurve GVRP Setup

as seen on Server Fault - Search for 'Server Fault'
I'm trying to setup GVRP on my 4 ProCurve switches. Currently I have a Layer 3 3500yl-24G (J8692A) which is connected to 3 Layer 2 2510G-48 (J9280A). I have three trunk ports setup on the 3500 connected to the 3 switches and currently everything seems to be working, the devices are talking to eachother… >>> More
Load-balancing between a Procurve switch and a server

as seen on Server Fault - Search for 'Server Fault'
Hello I've been searching around the web for this problem i've been having. It's similar in a way to this question: How exactly & specifically does layer 3 LACP destination address hashing work? My setup is as follows: I have a central switch, a Procurve 2510G-24, image version Y.11.16. It's… >>> More
Autonegotiate errors between HP and Cisco hardware?

as seen on Server Fault - Search for 'Server Fault'
This is a bit of a specific extension to this question. I've got two ASA's that feed into a Procurve switch, and then into an IPS. All is well except that the procurve absolutely refuses to autonegotiate with the ASA's...The asa's run 100full, and the procurve autonegotiates to 100half. It does it… >>> More
Is it possible to change the voltage on a single port on an HP ProCurve 2910al POE switch and how?

as seen on Server Fault - Search for 'Server Fault'
I have a couple of HP ProCurve 2910al POE+ switches at my company that we are primarily using to power our VOIP phones that run on 48V DC. However, I have one wireless access point that I need to run off of POE, but it has to be 24V DC. I'm afraid to plug it into the POE ProCurve because I'm not… >>> More
iSCSI SAN Implementation with several ESXi hosts and two Equallogic SANs

as seen on Server Fault - Search for 'Server Fault'
I work for a small state college. We currently have 4 ESXi hosts (all made by Dell), 2 EqualLogic SANs (PS4000 and PS4100) and a bunch of old HP Procurve switches. The current setup is very far from being redundant and fast so we want to improve it. I read several threads but get even more confused… >>> More

Related posts about switches

Hubs/switches taking out switches?

as seen on Server Fault - Search for 'Server Fault'
Here's the issue...we have a network with a lot of Cisco switches. Someone plugged in a hub on the network, and then we started seeing "weird" behavior; errors in communication between clients and servers, or network timeouts, dropping network connections, etc. It seemed that somehow that hub (or… >>> More
SNMP based network discovery (switches), device (ports on switches) power management

as seen on Server Fault - Search for 'Server Fault'
In a enterprise network, what would be the right way to generate a list of switches (SNMP managed) Is it reasonable to ask the organization to supply a list such as this: Switch name IP Address of switch Location SNMP community strings Or are there standard ways to run discovery scans -… >>> More
HP Upgrades SAN Storage, OEMs QLogic Fibre Channel Switches

as seen on Internet.com - Search for 'Internet.com'
HP unveils new offerings for iSCSI and Fibre Channel storage networking environments. >>> More
HP ProCurve GVRP Setup

as seen on Server Fault - Search for 'Server Fault'
I'm trying to setup GVRP on my 4 ProCurve switches. Currently I have a Layer 3 3500yl-24G (J8692A) which is connected to 3 Layer 2 2510G-48 (J9280A). I have three trunk ports setup on the 3500 connected to the 3 switches and currently everything seems to be working, the devices are talking to eachother… >>> More
Linksys/Cisco Small Business SRW-Series (ie SRW248G4) - Overcoming the Limitations

as seen on Server Fault - Search for 'Server Fault'
We just purchased a Cisco/Linksys SRW 248G4 switch to try it out. We have always had unmanaged switches before, and this is our first "somewhat managed" switch. So far the major limitations are: Only Internet Explorer 6 (manual says IE 5.5!) works for the web interface SSH exists but is not practically… >>> More