Search Results

Search found 7204 results on 289 pages for 'almost dead'.

Page 112/289 | < Previous Page | 108 109 110 111 112 113 114 115 116 117 118 119  | Next Page >

• Laptop abruptly powers off after few seconds of booting

  - by Alan Mendelevich

  I have a 3 year old HP Pavilion dv2208 laptop. Recently it started abruptly powering off in like ~20-30 seconds into Windows boot sequence after almost every reboot/shutdown. Even if I leave it in Repair/Start Windows Normally stage it powers off anyway. The only way I managed to workaround this is to enter BIOS setup screen and leave it on for no less than 10 minutes. I don't know what happens there but this helps every time. Any ideas of possible ways to fix this that don't include replacing motherboard are highly appreciated. P.S.: I've tried resetting BIOS to defaults, updating to the latest BIOS version, etc. Happens with both Vista and Windows 7.

  Read the article

• When connecting to PPTP Centos via Windows 7 VPN, I get error 2147943625

  - by Charlie Dyason

  The remote computer refused the network connection. phrase has been my arch enemy for the past week now I recently "bought" a VPS server, I gave up trying to configure it with OpenVPN, all the issues were making me lose my mind, so I tried the easier way with pptp, but i figure, both are leading to a dead end... I followed this post (many others too but this is the unlucky one), http://blog.secaserver.com/2011/10/install-vpn-pptp-server-centos-6/ and it all goes well with the setup, however, I run into this error when connecting to the VPN in Windows 7 here is a pic of the error: Image So I do not know what I have done wrong... When connecting, Code: Select all netstat -apn | grep -w 1723 before connecting: netstat -apn |grep -w 1723 tcp 0 0 0.0.0.0:1723 0.0.0.0:* LISTEN 1137/pptpd after the error came I tried again: netstat -apn |grep -w 1723 tcp 0 0 0.0.0.0:1723 0.0.0.0:* LISTEN 1137/pptpd tcp 0 0 41.185.26.238:1723 41.13.212.47:49607 TIME_WAIT - iptables: # Generated by iptables-save v1.4.7 on Fri Nov 1 18:14:53 2013 *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [63:8868] -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -i eth0 -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -p tcp -m state --state NEW -m tcp --dport 22 -j ACCEPT -A INPUT -i eth0 -p tcp -m tcp --dport 1723 -j ACCEPT -A INPUT -i eth0 -p gre -j ACCEPT -A FORWARD -i ppp+ -o eth0 -j ACCEPT -A FORWARD -i eth0 -o ppp+ -j ACCEPT -A INPUT -j REJECT --reject-with icmp-host-prohibited -A FORWARD -j REJECT --reject-with icmp-host-prohibited COMMIT # Completed on Fri Nov 1 18:14:53 2013 # Generated by iptables-save v1.4.7 on Fri Nov 1 18:14:53 2013 *nat : PREROUTING ACCEPT [96:12732] : POSTROUTING ACCEPT [0:0] : OUTPUT ACCEPT [31:2179] -A POSTROUTING -o eth0 -j MASQUERADE COMMIT # Completed on Fri Nov 1 18:14:53 2013 options.pptpd the only changes was the require-mppe # BSD licensed ppp-2.4.2 upstream with MPPE only, kernel module ppp_mppe.o # {{{ refuse-pap refuse-chap refuse-mschap # Require the peer to authenticate itself using MS-CHAPv2 [Microsoft # Challenge Handshake Authentication Protocol, Version 2] authentication. require-mschap-v2 require-mppe # Require MPPE 128-bit encryption # (note that MPPE requires the use of MSCHAP-V2 during authentication) require-mppe-128 # }}} I check the iptables, everything is normal, all INPUTs, etc are before rejects, username and password I also checked in chap-secrets file, I am really puzzled...

  Read the article

• How to get HTTP preseed to work correctly on Ubuntu 10.04 LTS (Lucid)?

  - by netvope

  Installation media: ubuntu-10.04-desktop-i386.iso I tried a lot of different boot parameters, but either the installer ignored the preseed configuration, or it boot itself directly as LiveCD. An example of the boot parameters I've tried: auto url=http://mydomain.com/path/preseed.cfg boot=casper only-ubiquity initrd=/casper/initrd.lz quiet splash -- If I remove only-ubiquity, it boots as a LiveCD. If I remove boot=casper, it won't boot. If I add vga=normal locale=en_US console-setup/layoutcode=us console-setup/ask_detect=false interface=auto, it still can't do automatic install. If I remove auto, it's the same. What is the correct boot parameters for launching such an installation? From the apache log of the server hosting preseed.cfg, I see that the installer has no problems fetching the preseed file. My preseed file is almost identical to the one at https://help.ubuntu.com/10.04/installation-guide/example-preseed.txt. Moreover, I have run debconf-set-selections -c preseed.cfg to ensure that the preseed file is correct.

  Read the article

• Dell Latitude E4300 TouchPad - Odd Behavior

  - by Cade Roux

  I'm seeing some intermittent behavior on the touchpad. First it wasn't working at all. Then during restart, for a little while it seemed like the buttons attached to the joystick and external mouse were both swapped left/right. Then I went in to the dell touchpad control and disabled the touchpad and re-enabled it and nothing happened. Then a short while after disabling the joystick the touch pad started working. So I restarted to see if it would keep the settings and before login, the touchpad appeared to work, then after login it stopped working for a few minutes while login continued. Then after the login was almost completed it started to work again. It appeared to have retained the settings for the disabled joystick. It seems like perhaps there are conflicting mouse drivers trying to simultaneously or similar. This doesn't seem normal for the touchpad to be disabled for so long after login. What steps should I take to ensure the drivers are right?

  Read the article

• connect to ssh server thru 80 via HTTP proxy?

  - by im_chc

  Hi, Please help: I want to connect to my ssh server at home However, I'm behind a corporate (CORP) firewall, which blocks almost all ports (443, 22, 23 etc). But it seems that 80 is not blocked, coz I am able to surf the web after I login (i.e. IE sets to CORP's proxy server, and start IE - displayed CORP intranet portal - type in google.com - dialog pops up for userid + pwd - login successful, and surf without restrictions) My ssh server listens at 443. My question is: Is there a way to connect from a computer behind the CORP firewall to the ssh server thru the 80 port, with the ssh server still listening on port 443? Changing the ssh server to listen to port 80 is not an option, coz my home ISP blocks 80. Can I use a public proxy which listens at 80? After some research on google I found that there is something called "connect to SSH thru an HTTP proxy" using the Cockscrew software. Is it useful? Or is there some other way to solve the problem?

  Read the article

• RDP for High DPI Monitors?

  - by Joey

  A client is having some problems with their laptop. They use RDP to remote into their work PC, but the laptop they are using is a small 13" Sony Vaio laptop, but with 1920x1080 resolution. Everything is pretty small on the laptop anyway, but the problem is much worse after connecting with RDP, where everything is almost unreadable. I have done the obvious with changing the resolution on the server, the RDP size, forced scaling on the terminal server etc, but nothing has worked. Something else which I would normally do is change the laptop resolution to something a little lower, but the laptop only has 2 resolution settings, the big one, and a 1024x768 (wrong ratio). Any ideas?

  Read the article

• Thunderbird gives " Not enough disk space " alert, after trying to download more emails ( Win 7, 64 bit )

  - by James C

  So, today I have installed Mozilla Thunderbird 24.2.0 on my Windows 7 (64 bit) machine. It was downloading emails, until it hit an error. An alert showed up saying : "There is not enough disk space to download new messages. Try deleting old mail, emptying the Trash folder, and compacting your mail folders, and then try again." Now, disk space is not a problem, there is enough free space left ( almost 50 % of the drive ). How to stop the alert and continue downloading ?

  Read the article

• Restore access to Cisco Connect after changing router settings

  - by StasM

  I have recently bought Cisco Valet Plus (M20) wireless router (which I recognize now was a mistake, but nevermind). It has two setup options - Cisco Connect software and web-based setup. Cisco Connect software allows changing very small set of settings, web-based setup allows access to almost all settings, except settings for guest network. The problem is that when I use web-based setup, Cisco Connect after some changes refuses to talk to the router, so I can't change guest settings anymore (since web interface doesn't allow to change them). It must be because of some config parameter not matching or some password set wrong - but I don't know where Cisco Connect stores them. So, does anybody have any idea how to make Cisco Connect talk to the router again once I changed the settings through the web interface?

  Read the article

• How to configure 1080p HDTV as a monitor

  - by Robot

  I've read several posts that almost answer my question, but not quite. I have a Samsung LN32C530 1080p HDTV I'd like to use as a monitor. I was reasonably successful getting the prior 720p model to work ok using SwitchResX, but I think I just got lucky with the parameters (1360x768@60Hz). I tried the expected (1920x1080@60Hz) values and "nearby" ones, with no luck. Older 720p params actually work, but I get the same small real estate as the older model TV. Trying values near 1080p always displays an image that doesn't match the screen size and is very jagged which makes me think interpolation is making things worse. Also, SwitchResX has a bunch of parameters other than H x W ("porch" etc), and I don't know how they all work together. Any help?

  Read the article

• Laptop charger disconnects and reconnects, charger or battery broken?

  - by Rob

  I've got an Acer Aspire One netbook (AOA-150) and there's obviously something wrong with it. The charging port gets VERY HOT and the charger seems to disconnect and reconnect quickly sometimes. This only happens when the netbook is running, and it doesn't seem to care what it's doing other than being on. The battery has an extremely short life (< 30minutes, sometimes) and I almost exclusively run it on the power cable (which needs the battery plugged in. Having it just plugged into the wall won't start up). Does this sound like a problem with the power cable or the battery? The plug for the cable and the port get so hot that if I held them for longer than a few seconds, I'm sure I'd get burnt. EDIT Just got "Popular Question" on this and it WAS the power jack. The ground on it came loose from the board. A bit of solder on it and everything is working great again.

  Read the article

• Does btrfs balance also defragment files?

  - by pauldoo

  When I run btrfs filesystem balance, does this implicitly defragment files? I could imagine that balance simply reallocates each file extent separately, preserving the existing fragmentation. There is an FAQ entry, 'What does "balance" do?', which is unclear on this point: btrfs filesystem balance is an operation which simply takes all of the data and metadata on the filesystem, and re-writes it in a different place on the disks, passing it through the allocator algorithm on the way. It was originally designed for multi-device filesystems, to spread data more evenly across the devices (i.e. to "balance" their usage). This is particularly useful when adding new devices to a nearly-full filesystem. Due to the way that balance works, it also has some useful side-effects: If there is a lot of allocated but unused data or metadata chunks, a balance may reclaim some of that allocated space. This is the main reason for running a balance on a single-device filesystem. On a filesystem with damaged replication (e.g. a RAID-1 FS with a dead and removed disk), it will force the FS to rebuild the missing copy of the data on one of the currently active devices, restoring the RAID-1 capability of the filesystem.

  Read the article

• On Windows, what filename extensions denote an executable?

  - by Ken

  On Windows, *.exe, *.bat, *.cmd, and *.com all represent programs or shell scripts that can be run, simply by double-clicking them. Are there any other filename extensions that indicate a file is executable? EDIT: When I jump into a new project (or back into an old project!), one of the common things I want to do when looking around is to find out what tools there are. On Unix (which I've used for decades), there's an execute bit, so this is as simple as: find . -executable -type f I figured that on Windows, which seems to have a much more complex mechanism for "is this executable (and how do I execute it)", there would be a relatively small number of file name extensions which would serve roughly the same purpose. For my current project, *.exe *.bat *.cmd is almost certainly sufficient, but I figured I'd ask if there was an authoritative list.

  Read the article

• Laptop battery holds charge, but won't charge any more.

  - by Jeff

  Ok, I'm sure I will need to replace either my battery or my AC adapter, but would rather not buy one if the other is the problem. My problem is. I have a Sager laptop that gets quite a bit of use. The charging has always been a little bit odd. If I was in the process of using it, it would charge just fine and stay On AC power. If I left it alone, however(power settings to ONLY turn off the monitor) in either Ubuntu or Windows 7 it decides that it didn't want to use AC power anymore and would just start draining the battery until it died. Now, suddenly, it won't charge at all. The capacity was great up to this point which happened in an instant. It will recognize the battery but won't see the AC power if plugged in while the battery is in. I can power up the laptop without the battery and it works fine. If I plug in the battery while powered up it will claim it's charging it, but it stays at the same percentage. If I unplug the power, it will switch over to Battery fine, but I have to power down and unplug the battery to get it back on AC power. I've had dying/dead batteries before but they typically won't hold a full charge anymore but it still winds up to 100% then drops quickly when unplugged. This seems more like a chip problem in the battery to me, but I'm not sure. Any ideas?

  Read the article

• wbadmin incremental system state backup

  - by user74513

  I am doing system state backups on a Windows Server 2008 R2 Enterprise (Service Pack 1) machine and expected the backups after the first one to be incremental. However with each backup a new directory with vhd files are created and the vhd files are almost the same size as the with the first backup. So the backups does not seem to be incremental. I used the following command to do the backup: wbadmin start systemstatebackup -backupTarget:f: I played around with the settings under "Configure Performance Settings" in the Windows Server Backup plugin in Server Manager but according to the description at the top of the dialog these settings are not applied to system state backups. Are there any settings available for wbadmin system state backup to make the backups incremental?

  Read the article

• Piecing together low-powered hardware for an RS-232 terminal server

  - by Fred

  I'm working on reconstructing my Cisco lab for training/educational purposes and I found that the actual terminal server I have is dead. I have a couple of 8-port PCI serial cards which would be more than ample for my lab, but I don't want to leave my personal computer running to be able to access the console ports. Ideally I would access the terminal server remotely, either by SSH/RDP to the box (depending on what OS I go with) or by installing a software package that allows me to telnet directly to a serial port. I know I've found a program that does this under Linux in the past but its name escapes me at the moment. I'm thinking about scavenging for some old hardware, on eBay or something, to put together a low-powered PC. Needs to be something that: Has Low-power consumption Has at least 2 PCI slots (though I certainly wouldn't complain about having more) Has onboard Ethernet (or, if not, another PCI or ISA slot (not shared)) Can be headless once an OS installed (probably Linux) I'm currently leaning towards an old fashioned Pentium (sub-133MHz era) but I am wondering if anybody else knows of another platform/mobo that would suit these needs. Alternatively, I've been considering buying a Raspberry Pi and a big USB hub along with a bunch of USB-Serial adapters but this sounds like it'd get messy quick with cables and adapters all over the place, and I may not even have the same ttyS#'s between boots.

  Read the article

• Program broke my windows. Everything randomly minimizes even after multiple restarts

  - by Xitcod13

  I just installed LoL (league of legends) on my computer. The problem is that almost every time after I play the game, it minimizes all my windows which is really annoying. What is worse however is that afterwards other programs do this as well. In the internet browser doesn't minimize but it does loose focus. For example when i type it randomly looses focus and i have to click on the browser window again to it registers my typing. Is there any way to fix this? What can cause such a strange behavior?? In addition this problem persists even after restarting my computer. I previously thought it was internet driver. I no longer think so this happened right after I started playing the game and seems pretty persistent. Please read the comments for further information. This pretty much renders my computer useless. Even typing this takes a huge effort.

  Read the article

• Lookup Active Directory entry by implicit UPN

  - by Michael-O

  In our company exists a forest-wide UPN suffix company.com and almost all user accounts have the explicit UPN set to [email protected]. This value is also set in the Active Directory userPrincipalName attribute. Now we have an application where users perform authentication through Kerberos. So we are given the Kerberos principal, i.e. implicit UPN. We'd like to look up that user and retrieve several LDAP attributes. Since iUPN and userPrincipalName do not match anymore, the lookup is not possible. Is there any "official" way to retrieve a mapping from the Active Direcory? My workaround is to perform a LDAP bind against the realm component and search for the sAMAccountName attribute which matches the user id component of the iUPN. Searching for the mere sAMAccountName in the forest is not possible because the value is unique in the domain only.

  Read the article

• How long do managed gigabit ethernet switches take to boot up?

  - by Warren P

  One critical drawback that I have found in researching managed-switches, and one that I have some past experience with is that anything with "lots" of firmware is going to have lots of issues associated with that firmware. We are in the middle of researching rackmount gigabit switches (48 port). It looks like for 48 ports, our only choice is managed switches (Dell, Cisco/Linksys,HP, etc). What I want to know, that I can not find out much about is the boot-time for various managed switches. If you own one, can you please answer with the model number, and the cold boot time in seconds. I have read online that Linksys (now Cisco) SRW series sometimes take almost 5 minutes before they are fully booted up, and that is an unacceptable cost for us. I particularly want to know about Dell PowerConnect managed switch bootup time (model 3548 and 5448), and would like to confirm the 5-minute boot time on the SRW2048 or similar model, and any HP ProCurve boot up times. The composite of all those figures ought to form an interesting overall performance picture.

  Read the article

• Application (was Firefox) crash on first load on Ubuntu Linux on older Dell Laptop

  - by Ira Baxter

  I've had a Dell Latitude laptop since about 2000 without managing to destroy it. A month ago the Windows 2000 system on it did something stupid to its file system and Windows was completely lost. No point in reinstalling Windows 2000, so I installed an Ubuntu Linux on the laptop. Everything seems normal (installed, rebooted, I can log in, run GnuChess, poke about). ... but ... when I attempt to launch Firefox from the top bar menu icon, I get a bunch of disk activity, the whirling cursor icon goes round a bit and then (WAS: everything stops: icon, mouse. Literally nothing happens for 5 minutes. Ubuntu is dead, as far as I can tell. EDIT : on further investigation, spinning icon, mouse operated by touchpad freeze. There's apparantly a little disk activity occuring about every 5 seconds. I wait 5-10 minutes, behavior doesn't change) A reboot, and I can repeat this reliably. So on the face of it, everything works but Firefox. That seems really strange. The only odd thing about this system when Firefox is booting is that while it has an Ethernet port (that worked fine under Windows), it isn't actually plugged into an Ethernet. As this is the first Firefox boot since the Ubuntu install, maybe Firefox mishandles Internet access? Why would that crash Ubuntu? (I need to go try the obvious experiment of plugging it in). EDIT: I tried to run the Disk manager tool, not that I cared what it was, just a menu-available application. It started up like Firefox, I get a little tag in the lower left saying Disk P*** something had started, and then the same behavior as Firefox. At this point, I don't think its the Ethernet. Is it possible that the Ubuntu disk driver can't handle the disk controller in this older laptop? The install seemed to go fine.

  Read the article

• Server freeze - how to debug

  - by Petr Peller

  I am running a Debian virtual server with Apache, PHP, MySQL. There is just 1 website with very low traffic running but the server very often (almost everyday) freezes and does not respond. When this happens the server is unreachable from web browser or by SSH and I have to go to administration of my provider and perform server hard reset after this the server seems to work fine. How can I find out what is causing the freezes? Linux vm2797 2.6.32-5-amd64 #1 SMP Tue Jun 14 09:42:28 UTC 2011 x86_64 GNU/Linux

  Read the article

• How to generate an ASCII representation of a Unix file hierarchy?

  - by Jenn D.

  Hi, all. I'm looking for a quick and dirty way to generate some diagrams of some directories that have almost, but not exactly, the same hierarchy, so I can show them around at a meeting and we can decide which flavor we like best. I'm not interested in the "leaf" nodes, just the directories. The catch: I don't want to mess with X. This is a server system I deal with entirely through SSH. So I'm looking for something that will do ASCII layout, maybe with simple pipes-and-hyphens for lines or something. Does anyone know of such a utility? I'm sure I could write something myself, but it's such a fiddly little sort of project, with handling spacing and layout and such; I'd really like to discover that someone's done it for me. Alas, Google doesn't seem to know of such a thing...or if it does, it's hidden beneath heaps of excellent visual explications of the standard general Unix file hierarchy. Thanks!

  Read the article

• Repairing hard disk when Windows installation disk won't boot

  - by Echows

  I'm trying to recover some data from a faulty hard disk with Windows installed on it (on which Windows won't even boot). I have tried so far: Booting to Ubuntu live USB stick and running ntfsfix (didn't work) Trying to mount the broken partition when running Ubuntu from usb stick (doesn't mount) Running photorec image recovery tool from live Ubuntu (it found some stuff but not the images I was looking for) Now as a last resort I got myself a Windows installation on a USB stick so that I can try fdisk, but the installer doesn't work. The loading screen shows up and then the installer crashes. The installer works fine on other computers. I suspect that the installer is trying to read the hard drive to see if there's something there but when it can't read one partition, it crashes. On Ubuntu, I can mount other partitions except the one I'm interested in so at least the hard drive is not completely dead. So the question is, what options do I have left? To be more specific, my goal is to recover some images from the faulty ntfs-partition on the hard drive. Other than that, I don't care about the contents of the hard disk.

  Read the article

• Why you have create a full site - if the answer for everything is the one and the same ?

  - by Aristos

  regarding this question http://superuser.com/questions/131176/a-hidden-program-virus-send-hundred-e-mail-can-you-have-any-experience-on-som I am wondering, if everything is the same, why you have fix a so complicate site ? One simple answer can solve all ! (for you) Hope full I found answers elsewhere on internet, and this general answer did not help me almost at all. The problem there is a serious thread, special that the general answer did not give the solution - and I see and the full video on it. Please answer to this question !

  Read the article

• are blue ray disks the cheapest storage medium per Gb?

  - by oshirowanen

  The question is as simple as that really. Are bluray disks the cheapest storage medium per gb? I am recording video which is using about 32gb per day. So a month of that would be almost 1Tb. A year around 12tb. I want to store at last a years worth with the possibility of more if needed. To me it seems that cheap bluray disks world be the cheapest solution. But I wanted to get this confirmed.

  Read the article

• Apache mpm-itk Performance

  - by Matt Beckman

  I manage a bunch of VPSs with memory ranging from 1GB to 8GB. Most of these websites are Joomla websites, and the servers must support multiple sites/users/S-FTP. I use mpm-itk almost exclusively (mostly due to it's convenience in these shared environments). However, I'm aware it isn't known for performance, so I need some advice on making it faster. Due to the lack of documentation when I first went the way of mpm-itk, I included only one setting in the config, and that was to limit each user to 50 clients (the rest I left up to defaults): <IfModule mpm_itk_module> MaxClientsVHost 50 </IfModule> Are there any better alternatives available? Are there any settings supported in mpm-prefork or mpm-worker that are also supported in mpm-itk? Thanks!

  Read the article

< Previous Page | 108 109 110 111 112 113 114 115 116 117 118 119  | Next Page >