Search Results

Search found 7204 results on 289 pages for 'almost dead'.

Page 116/289 | < Previous Page | 112 113 114 115 116 117 118 119 120 121 122 123  | Next Page >

• Power supply issue? New Radeon5850's fan runs at full speed and PC doesn't boot.

  - by Kris

  I recently bought a new ASUS EAH5850 graphics board. I installed it a custom PC which had an ASUS p5n-e SLI mobo along with a 500w Thermaltake W0093RU power supply. Sometimes when doing a cold boot the 5850's fan will run at full speed and the PC will not boot. Powering off by holding down the power button and powering back on sometimes remedies the situation and everything boots normally. Warm reboots also never seem to have problems. For some reason though cold boots almost always do. Another issue I notice is that when the PC does boot normally it takes longer (+30 secs) to POST than with my last video card. I flashed the mobo with the latest available BIOS but it had no effect. Is my problem a power issue or incompatible motherboard or something else I'm missing?

  Read the article

• Server 2008 unresponsive after SP2 install.

  - by Dan

  I have a dev server that has an exact image of a production web server. The prod server only has SP1 installed on it. When I first fired up the dev box, the first thing I did was install SP2, and let it be. Almost every morning when I came in, the server was unusable. It would respond to ping, but RDP and the web site running on it were down. On the screen the screen saver was bouncing around, so it wasn't hard locked. But it was unresponsive to keyboard and mouse. So now I have to hard shut it down, but when it comes back up, the only thing in the event viewer is the unexpected shutdown, nothing else. I've since taken a fresh image of my prod box and put it on the dev server, and not installed SP2, and the dev box is humming along perfectly. I should also note that this is Server2k8 Web, 64bit Has anyone else seen anything like this?

  Read the article

• Internet Problem: Wireless connected but no connection to internet

  - by Josh K

  Hey i have a interesting network setup on a laptop here and for some reason the internet isnt working. I am connected to a secure network via wireless router and taskbar says i am connected and with good signal strength but in my internet browser i cant connect to any websites, the error is: This webpage is not available. (Chrome) I am using Chrome, but websites dont work on IE either. Heres a little background on the setup i have. I have a Ethernet connected to the laptop with a static ip, and then i have the wireless setup with DHCP enabled. I am using the ethernet to connect to the network (for remote desktop) but the wireless for internet (to avoid the network firewalls). this set up has worked fine for a few months, but i cant figure out what is going on now. Might be worth it to note it is a Lenovo Thinkpad and i just uninstalled ThinkVantage Access Connections (as it was giving me ample problems prior to this one, which i consider a step up) Tried repairing connection as well, let me know if you guys have any ideas please! EDIT: Solved-Dead Modem in the server room.... Sorry guys didn't have access to that myself

  Read the article

• change browser to open weblinks in thunderbird

  - by Bevor

  Hello, because it's almost obvious that either Thunderbird or Firefox freeze my whole system after some time, I'd like to not use FF at the moment and let Thunderbird run only for a short time as long as I check e-mails. Thunderbird web links should be opened with opera from now. For that I went in Thunderbird to Preferences-Advanced-General-Config Editor and set the following: network.protocol-handler.app.http -> /usr/bin/opera network.protocol-handler.app.https -> /usr/bin/opera network.protocol-handler.warn-external.ftp -> true network.protocol-handler.warn-external.http -> true network.protocol-handler.warn-external.https -> true Moreover I changed in Gnome in System-Preferences-Prefered Applications Opera as webbrowser and I checked in FF that it should warn if FF is not the default browser (obviously it isn't anymore). Unfortunately all of these settings doesn't work. Thunderbird still opens web links with FF. Any explantions why? (I already restarted Thunderbird although I don't have to, but no effect)

  Read the article

• How can something relevant to graphics completely kill a motherboard?

  - by leladax

  I was coding something in OpenGL and after a bug there was an 'OS slowed down' situation. After a few seconds the screen went blank and the laptop shutdown. Now not even a led turns on battery or not. It doesn't appear to be the AC or the battery since there was some battery when it died and when it's connected to the AC the laptop produces near the AC connection a very slight 'clicking' noise (very faint, one has to be very careful to notice it, I don't know if it was there forever tbh). I suspect the motherboard died, as in something from the point it gets AC or battery power and the point it actually feeds itself. But I can't figure out how that effect was produced by the OpenGL bug or graphics overheating. If the graphics died alone, it should at least give some indication that the laptop is barely alive, at least a led, a sound, anything, the laptop is instead completely dead (other than faint 'clicking' I mentioned). Does anyone have expert advice on this? I'm especially interested in any ideas connected to "graphics overheated/bugged ---- they killed motherboard". I have a very lengthy experience in that stuff as a hobbyist and it really puzzles me. It's not just a "AC died" situation I can easily google.

  Read the article

• Analyse frequencies of date ranges in Google Spreadsheet

  - by wnstnsmth

  I have a Google Spreadsheet where I would like to compute occurrences of date ranges. As you can see in my sheet, there is a column date_utc+1 which contains almost random date data. What I would like to do is put the date values into bins of 6 hours each, i.e., 12/5/2012 23:57:04 until 12/6/2012 0:03:17 would be in the first bin, 12/6/2012 11:20:53 until 12/6/2012 17:17:07 in the second bin, and so forth. Then, I would like to count the occurrence of those bins, such as bin_from bin_to freq ----------------------------------------------- 12/5/2012 23:57:04 12/6/2012 0:03:17 2 12/6/2012 11:20:53 12/6/2012 17:17:07 19 ... ... ... Hope it is clear what I mean. Partial hints are very welcome as well since I am pretty new to spreadsheeting.

  Read the article

• Kaspersky processing error Explorer.exe (recycle bin)

  - by aeternus828

  I get daily critical errors from Kaspersky involving Explorer.exe... The file in question is almost always in the Recycle Bin, or something on the desktop. Here is an example error detail: Event type: Processing error Application\Name: EXPLORER.EXE Application\Path: C:\WINDOWS\ Application\Process ID: 2364 Application\Options: C:\windows\Explorer.EXE Component: File Anti-Virus Result\Description: Processing error Object: C:\$Recycle.Bin\S-1-5-21-1403139956-787289773-2644151291-500\$RIKKQKS Object\Type: File Object\Path: C:\$Recycle.Bin\S-1-5-21-1403139956-787289773-2644151291-500\ Object\Name: $RIKKQKS Reason: Read error Google searches didn't offer much insight, so I thought I'd ask here if anyone has encountered a similar situation. Not sure if it's a bug, something to be concerned about, or an easy fix, etc. I usually just empty the recycle bin for a temporary fix, but would like to get to the root of the error. Thoughts?

  Read the article

• Clicks or ticks every minute when HDD is idle [closed]

  - by Ramy

  Possible Duplicate: Clicks or ticks every minute when HDD is idle My HDD is a My passport... It's 2 weeks old. I hear this tick or click followed by another one about 8-9 secs later, and they repeat every minute almost exactly... They usually happen and the LED light blinking.. It's not like the other clicks you hear that indicate any inevitable HDD failure, it's much lower in volume. I don't know what that is, however it's different than the rest of the HDD usual sounds...It's close to the sound of the mouse click. It sometimes also happens when I access a file on the drive mostly after being idle for a while, sometimes randomly not really sure... The drive though is working well, the SMART report comes out OK and without warning, and disk management shows it healthy... What could be the cause of this??

  Read the article

• Video converters don't work anymore after reinstalling Windows

  - by tassiekev

  A few days ago, I decided to reinstall Windows 7 as my HD partition seemed to be nearly full and things were slowing down. I'd been using Handbrake almost exclusively to convert TV recordings and used Freemake on occasion. Following the reinstall, I can't get either to work: Handbrake says it's encoding for about 2 seconds and then says it's finished, but there are no converted files of any size. Freemake just says 'Conversion Error' and won't go any further. As an experiment I tried two programs that I don't normally use, VideoReDo & Any Video Converter. Both worked fine. Anyone got any clues?

  Read the article

• Can you suggest some DIY PC specs for 1) Value, and 2) Future 'upgradability'?

  - by user17381

  Hi, I'm considering building a new desktop PC from components. For the last 7/8 or so years I have almost exlusively used laptops, and so have fallen behind a bit with knowledge of various hardware technologies. Anyway, now I'm considering building a new desktop machine. Mainly for development work, but also would be nice to do a bit of gaming. The two main criteria are: I would like the first build to be relatively low cost. I would like to select components that will allow me to upgrade in the future without throwing too much away. Can anyone recommend a setup? Thanks

  Read the article

• Options for transparent data encryption on SQL 2005 and 2008 DBs.

  - by Dan

  Recently, in Massachusetts a law was passed (rather silently) that data containing personally identifiable information, must be encrypted. PII is defined by the state, as containing the residents first and last name, in combination with either, A. SSN B. drivers license or ID card # C. Debit or CC # Due to the nature of the software we make, all of our clients use SQL as the backend. Typically servers will be running SQl2005 Standard or above, sometimes SQL 2008. Almost all client machines use SQL2005 Express. We use replication between client and server. Unfortunately, to get TDE you need to have SQL Enterprise on each machine, which is absolutely not an option. I'm looking for recommendations of products that will encrypt a DB. Right now, I'm not interested in whole disk encryption at all.

  Read the article

• Dual-monitor Windows XP, monitors are "identified wrong"

  - by Susan

  Trying to use a dual-monitor desktop system with Windows XP.... 1 graphics card... with digital/analog outputs. Picking: Desktop - Properties - Settings - Identify It shows "2" as my left monitor... and "1" as my right. How do I switch them around? Here's what I've tried so far: Switch the cables (I can't. I need the digital cable on the better monitor.) Switch the monitors (I can't. One has a few dead pixels.) Drag the 1+2 graphics around (That doesn't change the IDENTIFY numbers.) Pick "use as primary" or "extend" (That doesn't change the IDENTIFY numbers.) Anything else I can try? What exactly controls/switches the "IDENTIFY numbers" around? I know it can be done. For weeks I ran this exact set-up... with the CORRECT numbers appearing on the monitors.... then just recently... after a few reboots... they now appear "switched around".

  Read the article

• Different BSOD every time I turn on computer

  - by Gemboz

  Please help. Every time I turn on computer I receive a different BSOD. I can't even give my computer info because I haven't been able to stay on it long enough. The following are the BSOD that I just received in the last hour. IRQL_NOT_LESS_OR_EQUAL PAGE_FAULT_IN_NONPAGED_AREA BAD_POOL_HEADER MEMORY_MANAGEMENT I has also started with Windows Error Recovey which I have done but that has froze on me or hasn't helped. I have also reset computer to its original state. Now as soon as I turn on it goes to a BSOD almost immediately. I know you need more info about computer, so if you can tell me what info it is you need, I will get it. I can tell you that it is a desktop.

  Read the article

• Recover data from Dynamic Disk (MBR) bigger than 2TB

  - by Helder

  Here is the situation: Promise Array FastTrak TX4310 with 3 disks (750 GB each) in RAID5. This comes to around 1500 GB of data. Last week I had the idea of expanding the RAID with an additional 750 GB disk. This would bring the volume to around 2250 GB. I plugged the disk and used the Webpam software to do the RAID expansion. However, I didn't count with the MBR 2TB limit, as I didn't remembered that the disk was using MBR instead of GPT and I didn't check it prior to the expansion. After a couple of days of expansion, today when I got home, the disk in Windows disk manager showed the message "Invalid disk" and when I try to activate it, it says "The operation is not allowed on the Invalid pack". From what I figured, the logical volume on the RAID expanded, and passed that info to the Windows layer and I ended up with an "larger than 2TB" MBR disk. I'm hopping that somehow I can still recover some data from this, and I was wondering if I can "rewrite" the MBR structure back to the 1500 GB partition size, so I can access the partition in Windows. Right now I'm doing an "Analyse" with TestDisk, as I hope the program will pickup the old 1500 structure and allow me to somehow revert back to it. I think that even though the Logical Drive in the RAID is bigger than the 2TB, I can somehow correct the MBR to show the 1500 GB partition again. I had a similar problem once, and I was able to recover the data using a similar method. What do you guys think? Is it a dead end? Am I totally screwed because there is the extra RAID layer that I'm not counting? Or is there other way to move with this? Thanks all!

  Read the article

• How to set default permissions for automounted FAT drives in Ubuntu

  - by piman

  I've got many FAT32 drives that I'd like to mount in Ubuntu such that they have permission mode 700 for directories and 600 for all other files. By default, they have 755 for all files, which is not particularly useful since almost no non-directories should be executable, and it screws up version control repos hosted on the drives. "Back in the day" I would have had the drives listed in /etc/fstab with the umask/dmask I want and there was no such thing as a default. These days, drives automount under their volume names. Which is great, except now I have no idea how to set the default. I have tried changing the /system/storage/default_options/vfat/mount_options gconf key with no apparently effect. It was 077 initially but the mounted drive reflected a default of 022; changing it and re-inserting the drives resulted in the files still having permission bits of 755.

  Read the article

• Making a hidden truecrypt volume with existing data

  - by Bill Grey

  I have a 1TB hdd, which I would like to encrypt. I would like to make a hidden volume, with almost nothing within but some decoy data, and the rest in a hidden volume. However, my driver is over 95% full. Is it still possible to do this, or would it have to be done on an empty drive, and then copy the data over? I could not find the answer to this question in the documentation. Also, how easy would it be to undo, or unencrypt the drive? Would it again need another empty drive to begin with?

  Read the article

• MySQL Locking Up

  - by Ian

  I've got a innodb table that gets a lot of reads and almost no writes (like, 1 write for every 400,000 reads approx). I'm running into a pretty big problem though when I do INSERT into the table. MySQL completely locks up. It uses 100% cpu, and every single other table (in other databases even) have their statuses set to "Locked" until the INSERT is done. This is a big problem because MySQL stays locked up for up to 4 minutes. I'm using version 5.1.47 (rpm from mysql.com). Any ideas?

  Read the article

• fdisk -l only displays boot partition

  - by Franklin

  I have a SAN, and it's able to read and write to the 50TB RAID just fine, but when I run fdisk -l it only lists the boot partition of the SAN server, and doesn't display anything about the other partitions on the RAID. I've also tried using parted -l with the same result. Now when I type mount it shows that the partitions are mounted just fine. I've never seen this happen. The box is running Openfiler 2.3 (I know it's old, we're in the process of upgrading all our old equipment). We have another SAN that's configured almost identically, and it's able to display the partition info with either of the two commands I mentioned above.

  Read the article

• How do you manage updates without a staging environment: CentOS 6.3

  - by Gregg Leventhal

  I am managing about 20 servers, many of them virtual. They are almost all different purpose, and none are clustered. I have a distributed LAMP stack, a few application servers, some build servers, a few KVM hosts. They are CentOS 6.3 mostly with a few Ubuntu (unfortunately). I don't have the resources to setup a staging environment where I can have duplicates of my machines and test updates before rolling them out. I am taking file backups. What I want to know is how you are approaching backing up your Linux systems. I assume you don't just do yum update, but then how are you choosing the packages worthy of updating? When (if ever) are you updating the kernel, etc.. How do you test updates without a staging environment? Snapshot and hope for the best?

  Read the article

• BIOS and Windows cannot detect CDROM device

  - by eman

  Hello! I have a HL-DT-ST RW/DVD GCC-4521B dvdrom device and a big problem. Some days ago everything worked fine. A friend installed some software and then the drives in winxp has been marked as corrupt. I uninstalled the software, but still corrupt drives. The next step I have done was running the current software GCC-4521B101(E).exe. When I ran this software again, the drives was automatically updated, but still marked as corrupt (in the Device Manager), even if I did a reboot. And then the big mistake: once more I tried to run this software, but during the update process, the machine restarted and boom! The DVDROM device doesn't work anymore. The led doesn't blink and if I push the eject button, nothing happens. Also bios and winxp doesn't recognize the optical drive. Then I plugged an other optical drive and it worked, but my old drive seems to be dead. So, what happened and how to solve this problem? Please help. Regards!

  Read the article

• How do I upgrade Django 1.3.1 to 1.4? Any tips, tutorials, or warnings?

  - by hobbes3

  Django 1.4 was recently released. Almost all the information about Django 1.4 is in the release note, but I didn't see anything about how to upgrade. Should I just remove the django folder inside Python's site-packges and download 1.4? I think I originally installed Django using emerge and yum but I'm not sure if the package management systems are up-to-date with Django 1.4 yet. That might be ok on my server instance (Gentoo Linux), but on my local instance I am using virtualenvwrapper (on Mac OS 10.7), so maybe I want to create a new Python virtual environment for Djago 1.4. Or maybe not since I don't really care about backward compatibility with 1.3.1.

  Read the article

• ATI Radeon Drivers works with which linux distribution and version?

  - by amit.codename13

  I have ATI Mobility Radeon HD 5850 graphics card. Almost every new linux distribution seems to have an issue with it, when i install the drivers. Working without utilizing the graphics card leaves me so unproductive. So i made a plan to use older versions of linux, any distribution suitable as a desktop distribution. UPDATE: The kind of problems that i am facing are, 1) After installing drivers the system boots and hangs, 2) There are unusual lines over the screen 3) After upgrade system doesn't start properly(hangs the usual old way) The kind of answers i am looking for is, distribution X(the newer the version the better) doesn't have the above problem after installing drivers for ATI Mobility Radeon HD 5850 graphics card. UPDATE: The new drivers released by AMD seems to fix all the issues, although they are still beta Thanks

  Read the article

• USB question (how durable is it, how should I workaround this)

  - by Shiki

  The plot is quite simple. Got a Razer mouse. If I plug it in, it works. After a shutdown/hibernation, I have to replug it entirely at the back of the PC. (It works in my laptop even after severel shutdown, etc, so yes I guess it's my motherboard.. but it still got 2 years of warranty and it comes with quad SLI, its not an old motherboard at all. (MSI P7N SLI FI (bought it after a hungarian guy's recommendation)). So. I only could come up with one "solution". Get 3 USB cable (you know, USB-USB). If its possible the shortest ones (don't know if the responsibility/anything will worsen), AND replug only the middle+closest to the USB port junction, since those are replaceable. What do you think? Any other idea? (BIOS is updated, mouse driver ... doesn't really matter, the mouse won't even blink a bit after this happens. It lights up and goes totally dead.)

  Read the article

• Generate metadata of all files in a dir?

  - by nmuntz

  We are working on a project that is quite big, and its stored in an SVN repository under different folders with many files all over the place. Quite often, it is hard to locate the document that has a certain keyword or phrase. Does anyone know of any program that will generate and index the metadata of all the files that are in these documentation folders? (most filetypes are: xls, doc, ppt). Windows Search and Google Desktop could be an option but that would generally index the whole hard drive, emails, etc and thats probably much more than what we need and would not be suited for something more folder specific. Example of what im looking for: a program or webpage where i enter "John Doe" and it will show me all files in MyProjectFolder/ that contain the keyword "John Doe". This of course will already be indexed somewhere so searches should be almost instantaneous. Is there such a tool or i am asking too much? Thanks in advance!

  Read the article

• Double Click to open Office docs is slow, File -> Open is fast.

  - by Keith

  I have 2 unique networks. They both share similar architecture: Windows 2003 SBS SP2 Running Symantec Endpoint Running Symantec Information Foundation Shared drives off a data partition Clients running Office 2003 or 2007 Connect to file server through mapped drives When users try to open a file from their local PC by double clicking, it will take 30-60 seconds to open. When they do File - Open, those same documents open up almost immediately. So far I've tried the following - CCleaner to parse the registry of outdated mapped drives - Disabled "using DDE" - Disabled A/V - Reboot Any ideas beyond that? Figured this question belongs here instead of SU since its the same issue on different networks.

  Read the article

< Previous Page | 112 113 114 115 116 117 118 119 120 121 122 123  | Next Page >