Search Results

Search found 3994 results on 160 pages for 'dual wan'.

Page 112/160 | < Previous Page | 108 109 110 111 112 113 114 115 116 117 118 119  | Next Page >

  • GRUB error: unknown filesystem

    - by Ali
    I replaced my old laptop drive which was win7 and ubuntu dual boot with an SSD. Now I connected the old drive through a USB adapter and I want to boot from it. But this comes up: unknown filesystem grub rescue> As i need the programs from old drive I have to boot from it time to time and I don't want to install those software on the new drive. It takes so time to exchange the drives so I want to boot from USB. how can I fix this?

    Read the article

  • Internet doesn't work when enable local Lan

    - by rakesh yadav
    We have the following network setup: A) Router IP 192.168.51.49 B) Windows Server 2008 R2 with dual NIC: B1) WAN interface (192.168.0.2) ( Used for internet) B2) LAN interface (192.168.1.2) ( used for local connectivity) when i keep both LAN Enabled than my internet doesn't work, but if I disabled my local Lan than internet working fine. so please help me how can resolved this issue or should i need to do routing on my server Please find the below attached route print result C:\Users\Administrator>route print =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.51.49 192.168.51.50 276 0.0.0.0 0.0.0.0 192.168.30.227 192.168.30.228 266 192.168.30.224 255.255.255.240 On-link 192.168.30.228 266 192.168.30.228 255.255.255.255 On-link 192.168.30.228 266 192.168.30.239 255.255.255.255 On-link 192.168.30.228 266 192.168.51.48 255.255.255.240 On-link 192.168.51.50 276 192.168.51.50 255.255.255.255 On-link 192.168.51.50 276 192.168.51.63 255.255.255.255 On-link 192.168.51.50 276 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 202.56.230.5 255.255.255.255 192.168.51.49 192.168.51.50 21 202.56.230.6 255.255.255.255 192.168.51.49 192.168.51.50 21 192.168.26.124 255.255.255.255 192.168.51.49 192.168.51.50 21 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.51.50 276 224.0.0.0 240.0.0.0 On-link 192.168.30.228 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.51.50 276 255.255.255.255 255.255.255.255 On-link 192.168.30.228 266 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 192.168.30.227 Default 0.0.0.0 0.0.0.0 192.168.51.49 Default ===========================================================================

    Read the article

  • USB DVD Drive not recognised in Windows 7

    - by Kieron
    I have an external DVD drive (USB) which I'm trying to attach to a notebook but it's not recognised by Windows 7. I can see the device in the control panel, says it's working properly but doesn't show up in the explorer window so can't access it. I've got a dual boot with Ubuntu and it shows up fine in there, no problems so I know the drive and connection are fine. Have tried the upper and lower filters but no success. Thanks for any help you can provide.

    Read the article

  • DC on Hyper V Host

    - by Saif Khan
    I've read a few similar questions but wasn't clear. I have a small office (13) users and recently purchased a new single server (this is all I have to work with for now). Server specs Memory - 16GB Drives - 6 SCSI (2TB) PROCESSOR - DUAL QUAD I plan on making the Hyper-V host the DC and then 2 VMs, one for a file server and the other an application server. Question - since I am restricted to this single server, would it be a big issue making the Hyper-V host the domain controller? Your input greatly appreciated.

    Read the article

  • Optimal Memory Configuration for Dell PowerEdge 1800 (Windows Server 2000 32bit)

    - by David Murdoch
    I am upgrading the memory on a Dell PowerEdge 1800 Server running Windows Server 2000 (32 bit). My Computer Properties currently reports "2,096,432 KB RAM" (4 modules @ 512MB each). Crucial.com scan reports: "Each memory slot can hold DDR2 PC2-5300 with a maximum of 2GB per slot. Maximum Memory Capacity:  12288MB Currently Installed Memory:  2GB Available Memory Slots:  2 Total Memory Slots:  6 Dual Channel Support:   No CPU Manufacturer:  GenuineIntel CPU Family:  Intel(R) Xeon(TM) CPU 2.80GHz Model 4, Stepping 1 CPU Speed:  2793 MHz Installed in pairs of modules." We will be completely replacing the old 512 MB modules. Will there be any performance difference between installing 4 modules @ 1GB vs. 2 modules @ 2GB?

    Read the article

  • How do I recover from a grub renaming issue?

    - by Justin Ardini
    I am currently dual-booting Ubuntu 10.04 and Windows 7 with grub 1.98 as the bootloader. I recently decided to edit the grub menu to remove the old Ubuntu kernels, so I followed the instructions of this guide and added the line list='version_find_latest $list' to the 10_linux file, then ran sudo update-grub. Apparently I made a mistake, because upon restart I had these bootloader entries: Ubuntu, with Linux $list Ubuntu, with Linux $list (recovery mode) Ubuntu, with Linux version_find_latest Ubuntu, with Linux version_find_latest (recovery mode) When I try to load any of these, I get a grub error along the lines of, Error: not a normal file Now I can't start any version of Ubuntu to remove the line I added. What's the best course of action to be able to use Ubuntu again? Thanks.

    Read the article

  • Install Mouse Driver on Windows 7 Professional 64 bit

    - by Soren
    I have a mouse that I absolutely love (been using them for years), A4Tech WOP-35. It has dual scrollers and 5 buttons, 3 of the buttons are programmable. I use them at work and at home. At work I am using Windows 7 Enterprise (32 bit), at home I am using Windows 7 Professional (64 bit). The drivers installed easily on my machine at work. Unfortunately, they will not install on my computer at home. When I double click on the Setup.exe, it asks me if I want to install it, and of course I click on "Yes", but nothing happens. When I say nothing happens, I mean nothing happens; it appears that it doesn't even try to install. The same thing happens when I right click on the setup.exe and select run as administrator. How can I get around this? I am guessing it is because I am running the 64 bit version of Windows.

    Read the article

  • Squid with mikrotik router

    - by niren
    I tried to connect squid3 in my network to use high anonymity proxy. This is how my network is right now WAN LINK | ------------- ----------------------------- | Mikrotik Box | | Ubuntu Server with squid3 | ------------- ----------------------------- | / | / ---------------------- | Switch ( Cheap one ) | ---------------------- | | | Client1 Client2 Client3 etc. after this setup I changed squid.conf in Ubuntu server as http_port 8080 acl localhost src xxx.xxx.xxx.xxx(Ubuntu server IP) acl to_localhost dst xxx.xxx.xxx.xxx(Mikrotik router gateway) I assume that redirected http from Mikrotik router will be redirect again to Mikrotik router. uncomment access log /var/log/squid3/access.log add visible_hostname myname save squid.conf and restart squid3 server. Then I have added nat rule in Mikrotik router ip/firewall/nat 1. add chain=dstnat src_address=xxx.xxx.xxx.xxx(ununtu server IP) dst-port=80 protocol=tcp action=accept 2. add chain=dstnat src_address=xxx.xxx.xxx.xxx/28(LAN address) dst-port=80 protocol=tcp action=dst-nat to-address=xxx.xxx.xxx.xxx(ununtu server IP) to-port=8080 now I can not able to access internet from client1 system, If I remove these two nat rule then I can access internet. what is wrong I have made?

    Read the article

  • Remote desktop type software that the client need not install anything...

    - by allentown
    I am primarily a Macintosh user, and can usually walk a client though any troubles they may have because I have a Macintosh in front of me. If they are on a different OS, things are close enough, or I cam remember, that I can get by. When trying to help clients on Windows, I get stuck. I do not have access to windows, and even if I did, there are far too many versions of Outlook, all with their various esoteric settings and checkboxes, that I could never see exactly what they are seeing. I mostly need to just help them with email setup. Something like copilot.com may do the trick. What is the simplest remote control software out there, ideally, it would accomplish these: No software needed on remote end, or, a single .exe that they can toss when done. I need Mac based software on my end. I do have ARD, which support VNC Free :) If possible, it would be really nice Needs a port forwarding proxy run by the company. There is no way I can get the user to alter their router, or to even plug directly into their WAN for a short time. On the Mac, I just have them open iChat, and this is all built in, proxying through AIM, looking for the same for Windows and Mac.

    Read the article

  • RTL8168B/8111B Lan card is not detected in Redhat..Error is make ***/lib/modules/2.6.18-53.e15/build

    - by Deepak Narwal
    0 Hello friends... In My computer Lan card model is Realtek RTL8168B/8111B PCI-E GIGABIT ETHERNET NIC (NDIS 6.20) My system is dual boot windows 7 and redhat 5.1.Redhat is not picking up this model of Lan card automaticlly. I tried it by downloading from realtak site for this particular model and find some .tar packages for my kernal and when i tried to install them ... check old drivers & unload it build the module and install make */lib/modules/2.6.18-53.e15/build: no such file or directory stop make[1]: *[modules] error 2 make : [modules] error 2 i downloaded tar files from sites and unpack according to their instrution i tried to run autorun.sh script as mentioned in readme file but after doing this it is showing above error... Now what to do i am not getting

    Read the article

  • Cisco Catalyst 3550 + Alteon 184 Load-Balancing Issues...

    - by upkels
    I have just deployed a couple Cisco Catalyst 3550 switches, and a couple Alteon 184 Web Switches for load-balancing. I can ping all RIPs and VIPs to/from the Alteon. Topology Before: (server) <- (Alteon) <- (Internet) Topology Now: (server) <- (3550) <- Alteon <- (Internet) Cisco Port Configuration (Alteon Uplink Port): description LB_1_PORT_9_PRIMARY switchport access vlan 10 switchport mode access switchport nonegotiate speed 100 duplex full Alteon Port 9 Configuration (VLAN 10 WAN): >> Main# /c/port 9/cur Current Port 9 configuration: enabled pref fast, backup gig, PVID 10, BW Contract 1024 name UPLINK >> Main# /c/port 9/fast/cur Current Port 9 Fast link configuration: speed 100, mode full duplex, fctl none, auto off Cisco Configuration (Load-Balanced Servers Port): description LB_1_PORT_1_PRIMARY switchport access vlan 30 switchport mode access switchport nonegotiate speed 100 duplex full Alteon Port 1 Configuration (VLAN 30 LOAD-BALANCED LAN): >> Main# /c/port 1/cur Current Port 1 configuration: enabled pref fast, backup gig, PVID 30, BW Contract 1024 name LB_PORT_1 >> Main# /c/port 1/fast/cur Current Port 1 Fast link configuration: speed 100, mode full duplex, fctl both, auto on Each of my servers are on vlan 10 and 30, properly communicating. I have tried to turn on VLAN tagging on the Alteon, however it seems to cause all communications to stop working. When I tcpdump -i vlan30 on any of the webservers, I see normal ARP communications, and some STP communications, which may or may not be part of the problem: ... 15:00:51.035882 STP 802.1d, Config, Flags [none], bridge-id 801e.00:11:5c:62:fe:80.8041, length 42 15:00:51.493154 IP 10.1.1.254.33923 > 10.1.1.1.http: Flags [S], seq 707324510, win 8760, options [mss 1460], length 0 15:00:51.493336 IP 10.1.1.1.http > 10.1.1.254.33923: Flags [S.], seq 3981707623, ack 707324511, win 65535, options [mss 1460], len gth 0 15:00:51.493778 ARP, Request who-has 10.1.3.1 tell 10.1.3.254, length 46 etc... I'm not sure if I've provided enough information, so please let me know if any more is necessary. Thank you!

    Read the article

  • How to vertically split widescreen into two virtual workspaces on ubuntu/gnome?

    - by David
    My new laptop has a big 16:9 screen, and I'm finding it hard to fully utilize it during the 95% of the time that I'm not watching HD movies on it. I'd like to set it up as a kind of virtual dual screen by splitting the physical screen into two workspaces. I know I could arrange my windows manually, but I'd like to be able to maximize a window and have it only consume half the monitor, and have its pop up dialogs centered on its half-screen, that sort of thing. Is there some kind of plug in available to do this? Thanks in advance for any pointers.

    Read the article

  • Will Dolphin emulator run (smoothly) on this machine?

    - by Mark
    Product Specs: Intel® NM10 Express chipset /w Intel® Atom® D525 (dual-core, 1.8 GHz) I think the most I can put in there for RAM is 4 GB. (They don't make 8 GB SODIMM do they?) The Dolphin site is pretty vague about requirements: Windows XP or higher, or Linux, or MacOSX Intel Fast CPU with SSE2. GPU with Pixel Shader 2.0 or greater. Some integrated graphics chips work but it depends on the model (and only with DirectX 9). I'm trying to make a light-weight quiet little machine for streaming video and playing eumulators, and I'm trying to figure out the minimum requirements I will need to do what I want. I know I'm not supposed to ask for product recommendations here, so if you could just advise the minimum requirements in terms of CPU, graphics card, and RAM, that'd be helpful.

    Read the article

  • Which hardware changes require operating system reinstallation?

    - by Mark
    I'm about to upgrade my computer but might keep some parts. Just wandering what I would have to keep to prevent me having to reinstall my OSs, at the moment I have a dual boot setup with ubuntu and windows 7. I'm pretty sure you can't just take your hard drive with the OS on it and put it into a different box and keep going (can you?) but I know you can change the graphics cards, secondary hard drives and ram with out a problem. So what is it that you can't change? The CPU? Motherboard? Thanks for any replies

    Read the article

  • OpenVZ with brdiged interfaces and VLAN

    - by Deimosfr
    Hi, I've got a problem with OpenVZ with brdiged VLAN. Here is my configuration : +------+ +-------+ +-----------+ +---------+ br0 |VE101 | | | | OpenBSD |----->| Debian |------->| | | WAN |--->| Router | | OpenVZ | +------+ | | | Firewall |----->| br0 br1 | br1 +------+ +-------+ +-----------+ +---------+------->|VE102 | |br0 | | |VLAN br0.110 +------+ v +---------+ |VE103.110| +---------+ I can't make VLAN working on br0 (br0.110) and I would like to understand why. I don't have any switch so no problem with unmanageable switch. I've configured a VLAN interface on OpenBSD in /etc/hostname.vlan110 : inet 192.168.110.254 255.255.255.0 NONE vlan 110 vlandev sis1 And it seams working fine. I've also adapted my PF configuration to work with VLAN but I don't see any incoming traffic. On my Debian lenny, here is my interfaces configuration : # The loopback network interface auto lo iface lo inet loopback # br0 auto br0 iface br0 inet static address 192.168.100.1 netmask 255.255.255.0 gateway 192.168.100.254 network 192.168.100.0 broadcast 192.168.100.255 bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off # VLAN 110 auto br0.110 iface br0.110 inet static address 192.168.110.1 netmask 255.255.255.0 network 192.168.110.0 gateway 192.168.110.254 broadcast 192.168.110.255 pre-up vconfig add br0 110 post-down vconfig rem br0.110 It looks like ok, but when I start my VE, here is the message : ... Configure veth devices: veth103.0 Adding interface veth103.0 to bridge br0.110 on CT0 for VE103 can't add veth103.0 to bridge br0.110: Operation not supported VE start in progress... So I've got one error here. I've followed this documentation http://wiki.openvz.org/VLAN but it doesn't work. I've certainly missed something but I don't know why. Someone could help me please ? Thanks

    Read the article

  • Private staff network within public network

    - by pianohacker
    I'm the sysadmin at a small public library. Since I got here a few years ago, I've been trying to set up the network in a secure and simple way. Security is a little tricky; the staff and patron networks need to be separated, for security reasons. Even if I further isolated the public wireless, I'd still rather not trust the security of our public computers. However, the two networks also need to communicate; even if I set up enough VMs so they didn't share any servers, they need to use the same two printers at the very least. Currently, I'm solving this with some jerry-rigged commodity equipment. The patron network, linked together by switches, has a Windows server connected to it for DNS and DHCP and a DSL modem for a gateway. Also on the patron network is the WAN side of a Linksys router. This router is the "top" of the staff network, and has the same Windows server connected on a different port, providing DNS and DHCP, and another, faster DSL modem (separate connections are very useful, especially as we heavily depend on some cloud-hosted software). tl;dr: We have a public network, and a NATed staff network within it. My question is; is this really the best way to do this? The right equipment would likely make my job easier, but anything with more than four ports and even rudimentary management quickly becomes a heavy hit on our budget. (My original question was about an ungodly frustrating DHCP routing issue, but I thought I'd ask whether my network was broken rather than asking about the DHCP problem and being told my network was broken.)

    Read the article

  • open source solution to a gateway for a network of a housing cooperative of 150 people

    - by SirDinosaur
    i just inherited a barely functioning network for a student housing cooperative of about 150 people. in it's current state, as i understand it from the previous person in charge of the network, we have working wireless access points and working ethernet cords going to working gigabit switches going to a barely functioning gateway (right now a simple home router) to one of three possible outbound connections. it is possible to connect to the network through the wireless or ethernet, but especially during peak hours, packets / connections are likely dropped or otherwise get no response. my intuition tells me to replace the gateway with something that can handle multiple outbound connections (WAN) and one inbound connection (LAN), while the rest of the network seems suitable for now. i'm somewhat knowledgable in Linux (been using Debian after first Arch Linux) and i want to use as much open source as possible, but i'm confused whether or not a simple server that i could easily understand will work for this situation. do i need specialized hardware to handle the switching more effectively? if so, what are my options? (i found this, thoughts?) or if a Debian server would work, anything else i should about the specs required for this type of server? also links to any useful information on using open source to maintain this type of network would be most appreciated. <3 P.S. crossposted http://redd.it/yybp2.

    Read the article

  • Intel motherboard drops HDMI output after Windows boots

    - by Nick
    I have an Intel motherboard (DH67CL) that uses Intel HD 3000 video. It has two video output ports: HDMI and DVI. Both my monitors are DVI, so I have two cables: a DVI-DVI and an HDMI-DVI. If I plug a monitor into just one of these ports, things work fine. But if I plug monitors into each of the ports, the system startup screens show on both monitors, along with the "Starting Windows..." screen, but as soon as the system boots into Windows, the HDMI-connected monitor goes to sleep. When I use the Intel video control panel, the HDMI-connected monitor is not detected. How do I get a dual-monitor setup to work?

    Read the article

  • Better to develop Ruby project on server or buy a faster desktop computer? B/c laptop too slow.

    - by user33184
    I have a Linux laptop (Vostro V13) running a Celeron M chip. This is a fine laptop, but running unit tests especially for Rails applications is slow. I want a faster development environment but I don't want to spend too much money. So the choice I have is between $390 for a Linux desktop machine with a Pentium Dual Core Processor E5400 and just paying between $30 and $40 a month to Linode and trying to do development remotely on that server. Can anyone with experience developing server applications using both methods offer any advice?

    Read the article

  • Grub loading. The symbol ' ' not found. Aborted. Press any key...

    - by John
    Hi there, I have a dual boot system on dell xps 9000 with windows 7 and ubuntu. But after I performed system backup on it as requested by windows 7 I am no longer able to boot into the computer, instead at the beginning after bios I get the following message: Grub loading. The symbol ' ' not found. Aborted. Press any key... I tried to change bios booting config to starting with harddrive and it still returned the same message. Using windows boot disk only asks me to do another system backup or threatens to delete my harddrive completely. The only solution I have so far is to reinstall ubuntu, but that leaves 2 additional copies of ubuntu on my computer. Is there a simpler way to fix the situation so I can actually boot into windows? Thanks so much.

    Read the article

  • Vista won't boot - just get black screen

    - by DisgruntledGoat
    When I boot into Windows Vista (Ultimate), I just get a black screen (with the mouse visible and working). If I run in safe mode, it seems to pause for a while when loading crcdisk.sys. A lot of research says it could be a problem with the hard drive, but I dual boot Ubuntu and that works fine and I can still see and use the Windows partition absolutely fine from Ubuntu. I tried using the "startup repair" option on the Vista install disk but it didn't detect any problems. I have run chkdsk several times, with this: chkdsk C: /f /r And also drive D (the recycle bin). The first two times it detected and fixed errors on the C drive but now it doesn't detect any errors. Is there anything else that could be causing this problem?

    Read the article

  • Caching DNS server (bind9.2) CPU usage is so so so high.

    - by Gk
    Hi, I have a caching-only dns server which get ~3k queries per second. Here is specs: Xeon dual-core 2,8GHz 4GB of RAM Centos 5x (kernel 2.6.18-164.15.1.el5PAE) bind 9.4.2 rndc status: recursive clients: 666/4900/5000 About 300 new queries (not in cache) per second. Bind always uses 100% on one core on single-thread config. After I recompiled it to multi-thread, it uses nearly 200% on two core :( No iowait, only sys and user. I searched around but didn't see any info about how bind use CPU. Why does it become bottleneck? One more thing, here is RAM usage: cat /proc/meminfo MemTotal: 4147876 kB MemFree: 1863972 kB Buffers: 143632 kB Cached: 372792 kB SwapCached: 0 kB Active: 1916804 kB Inactive: 276056 kB I've set max-cache-size to 0 to make sure bind can use as much RAM as it want, but it always stop at ~2GB. Since every second we got not cached queries so theoretically RAM must be exhausted but it wasn't. Do you have any idea? TIA, -Gk

    Read the article

  • Simple Linux program that takes any HTTP/HTTPS request and returns a single page?

    - by ultrasawblade
    I have a Linux box operating as router. There's a NIC that's connected to the internet (WAN), a NIC connected to an 8-port GbE switch (LAN), and a NIC connected to a Linksys wireless N-router (WLAN). Routing between everything is working perfectly. I have security completely disabled on the wireless router, but the WLAN NIC is firewalled such that it will only accept DNS queries and PPTP VPN connections. Currently HTTP/HTTPS traffic and everything else is blocked. I would like to run something that listens on port 80/443 of the WLAN NIC, and, for non VPN'ed connections, given any HTTP/HTTPS request it will return a single webpage saying "Unauthenticated" and explain how to sign into the VPN. A transparent proxy seems to be what I need, but my searches all seem to direct me to Squid, which is already running on my server and seems overkill for this simple task. Is there a simpler, lightweight program out there that does just this or should I just suck it up and run two instances of Squid (or figure out how to configure it)? Or, is this entire VPN thing I'm doing complete nonsense and I should just enable encryption on the wireless router?

    Read the article

  • Find the IP of the router between me and main router/gateway?

    - by Crash893
    I have a Netgear router that is the main router/gateway in and out of the network. Then I have a Linksys 54g router with WiFi that we use as are main WiFi access point The Cat5 runs from the router to the WiFi routers LAN port (not WAN). And then if you connect to that WAP you are basically on the network. I want to be able to find out what the IP address of that WAP is but so far I can't figure out how to: I've tried doing a tracert to the gateway IP but I get nothing. I've scanned all the IP addressed in the network. I've gone to the Netgear main router and looked under attached devices but it doesn't say anything. Any ideas on how I can figure out how to administer it? (I do have limited physical access but my attempt to plug into it came back with a faulty IP (in the 169 range where the rest of the office is 192.168...). I never set this router up to begin with so I'm reluctant to just kill it with the reset button because I can't get into see what the settings are set to.

    Read the article

  • Ubuntu Karmic, Maximize delay problem

    - by Loukas990
    Hello, I have tried various ubuntu versions, Ubuntu Karmic Koala 9.10 x86, Ubuntu 10.04 beta DVD, Ubuntu 9.10 AMD64, Mandriva 2010 x86, also a Fedora version and after installing compiz on all OS's, everything is working normal and smooth, even the compiz effects, cube, water, fire, wobbling windows, etc, except of the Maximize effect, where i get 2seconds+ delay for the effect. Cause it got me in a lot of thinking, why im getting this delay "problem", do you think there is any solution? or at least a way to decrease the delay? Thanks in advance. ;) P.S. My laptop is a Toshiba Satellite P300d, AMD Turion 64 x2 Dual-Core TL-64 (2.20 GHz), ATI Mobility Radeon™ HD 3650 512MB, 3GB RAM.

    Read the article

< Previous Page | 108 109 110 111 112 113 114 115 116 117 118 119  | Next Page >