Search Results

Search found 23103 results on 925 pages for 'performance issues and ha'.

Page 112/925 | < Previous Page | 108 109 110 111 112 113 114 115 116 117 118 119  | Next Page >

• Lighttpd based server issues crop up when port forwarding

  - by michael

  I have four host computers running lighttpd webservers. they are sitting behind a hspa modem, which each occupying a http port between [81 - 84]. 80 is taken by the modem itself. The port forwarding is setup correctly, however, only a portion of any webpage I request from any of the hosts comes through (they all fails after %20 of the page). If I put the host on port 81 into the dmz, it serves pages fine. The others do not respond to the dmz treatment. Is it possible the web content on the hosts somehow require ports aside from their respective http port? Or is it possible that even though the server.port in the lighttpd_ssl.conf file is set, the individual hosts are still expecting to serve on port 80? I am not familiar with lighttpd, nor did i set them up. they are running on video encoders i purchased. I can grab any files from them required for further information on the problem.

  Read the article

• System Issues and Major Malfuctions after Failed hibernation Exit

  - by Sarah Seguin

  I have a HP G71-340US that went into hibernation mode for a while and when I tried coming out of it, I got an error message: You're computer cannot come out if hibernation . Status: 0xc000009a Info: A fatal error occurred processing the restoration data. File: \hiberfil.sys Any information that was not saved before the computer went into hybernation will be lost enter=continue So I hit continue and it ran soooo super slow it. It was seriously crawling. Finally I gave up and turned it off manually (IE press and hold the button). It's been a week or two since then and EVERY SINGLE TIME I have tried to to do ANYTHING it takes forever. When I say forever, I literally mean takes 5-7 minutes to load the internet, then the page itself, then to click a link, so on so forth. Eventually everything just goes not responding and I have to give up (4-6 HOURS later). I also cannot access my thumb/jump drives once I've managed to load windows. I was going to try runing malware bytes incase of a virus, but it's windows explorer developes errors and goes not responding on me. Currently I'm running scan disk or check disk and like every file is coming back unreadable. I let it run the last 2 hours straight in chkdesk and I'm only at 6 percent with around 500+ errors and still going. Yes, I've taken logs of the errors via cell phone camera and patience. A week or two prior to this happening I had to change our the hard drive due to blunt force trama next to the mouse. OH! Running on Windows 7: ) And I've tried loading the computer in safe mode and it makes absolutely no difference. Any and all help would be appreciated. I really don't know what to do from here and I'm kind of freaking out. I've googled different part of the error and things that I've done/seen and there are so many different answers/topics that I thought it best to just post the questions.

  Read the article

• Issues With IIS Hosting Two Domains From Same Folder

  - by Bob Mc

  I have two different domain names that resolve to the same ASP.Net site. Both domains are hosted on the same server, which runs Windows Server 2003 and IIS6. The sites are differentiated in IIS Manager using host headers. However, both of the sites point to the same folder on the local drive for the site's page files. I am occasionally experiencing an ASP.Net error that says "The state information is invalid for this page and might be corrupted." I'm the site developer so I've addressed all the relevant code-related causes for this issue. However, I was wondering whether having two domains/sites sharing the same folder for an ASP.Net application might be causing this intermittent error. Also, is this generally a bad practice? Should I make separate, duplicate folders for each of the domains? Seems like that can become a maintenance headache.

  Read the article

• Networking issues with WNR3500L

  - by ageis23

  When I try connecting to my wireless network it attempts to connect then gives up. There's something strange going on with the mac's. The eternet switch and all the vlan interfaces have a mac 00:FF:FF:FF:FF:FF. config 'switch' 'eth0' option 'vlan0' '2 3 4 8*' option 'vlan1' '0 8' option 'vlan2' '1 8' config 'interface' 'loopback' option 'ifname' 'lo' option 'proto' 'static' option 'ipaddr' '127.0.0.1' option 'netmask' '255.0.0.0' config 'interface' 'lan' option 'type' 'bridge' option 'ifname' 'eth0.1' option 'proto' 'static' option 'netmask' '255.255.255.0' option 'ipaddr' '192.168.2.1' option 'ip6addr' '' option 'gateway' '192.168.1.253' option 'ip6gw' '' option 'dns' '' config 'interface' 'wan' option 'ifname' 'eth0' option 'proto' 'dhcp' option 'ipaddr' '192.168.1.8' option 'ip6addr' '' option 'netmask' '255.255.255.0' option 'gateway' '192.168.1.253' option 'ip6gw' '' option 'dns' '192.168.1.253' config 'interface' 'dmz' option 'ifname' 'eth0.2' option 'proto' 'static' option 'ipaddr' '192.168.0.1' option 'netmask' '255.255.255.0' Any help on this will be greatly appreciated! When I try setting the mac using macaddr it does nothing. It works perfectly fine when I turn the authentication off.

  Read the article

• Issues with "There is already an object named 'xxx' in the database'

  - by Hoser

  I'm fairly new to SQL so this may be an easy mistake, but I haven't been able to find a solid solution anywhere else. Problem is whenever I try to use my temp table, it tells me it cannot be used because there is already an object with that name. I frequently try switching up the names, and sometimes it'll let me work with the table for a little while, but it never lasts for long. Am I dropping the table incorrectly? Also, I've had people suggest to just use a permanent table, but this database does not allow me to do that. create table #RandomTableName(NameOfObject varchar(50), NameOfCounter varchar(50), SampledValue decimal) select vPerformanceRule.ObjectName, vPerformanceRule.CounterName, Perf.vPerfRaw.SampleValue into #RandomTableName from vPerformanceRule, vPerformanceRuleInstance, Perf.vPerfRaw where (ObjectName like 'Processor' AND CounterName like '% Processor Time') OR(ObjectName like 'System' AND CounterName like 'Processor Queue Length') OR(ObjectName like 'Memory' AND CounterName like 'Pages/Sec') OR(ObjectName like 'Physical Disk' AND CounterName like 'Avg. Disk Queue Length') OR(ObjectName like 'Physical Disk' AND CounterName like 'Avg. Disk sec/Read') OR(ObjectName like 'Physical Disk' and CounterName like '% Disk Time') OR(ObjectName like 'Logical Disk' and CounterName like '% Free Space' AND SampleValue > 70 AND SampleValue < 100) order by ObjectName, SampleValue drop table #RandomTableName

  Read the article

• Storage sizing for virtual machines

  - by njo

  I am currently doing research to determine the consolidation ratio my company could expect should we start using a virtualization platform. I find myself continually running into a dead end when researching how to translate observed performance (weeks of perfmon data) to hdd array requirements for a virtualization server. I am familiar with the concept of IOPs, but they seem to be an overly simplistic measurement that fails to take into account cache, write combining, etc. Is there a seminal work on storage array performance analysis that I'm missing? This seems like an area where hearsay and 'black magic' have taken over for cold, hard fact.

  Read the article

• Fixing Windows 7 explorer issues

  - by Cegorach

  OK, so here is the problem I'm hoping you guys can help me fix. On my Win7-Ult64 box, my explorer (among other things) has decided not to work. For example, if I try to use a program, say Chrome, to open a folder, I will get the message "Class not registered" (and its not program specific). In the same vein, when I go to Start-Rclick Computer-properties, nothing happens, but I can go to control panel-system properties and it will work. And other items in the control panel do nothing when I click them (and I have a feeling it is all tied together). I have already done multiple virus and spyware sweeps, so I know that isn't the problem. Any suggestions on what could be causing this/how to fix it (short of nuke and boot)?

  Read the article

• Apache form authentication issues

  - by rfcoder89

  I am trying to authenticate users through Apache using the form authentication method to restrict https requests to a certain folder. Although, regardless of whether the correct login details are provided it keeps reloading the same page except the url has the form values embedded in it instead of redirecting to the appropriate page. I need to use the form authentication type instead of basic so I can write my own html for the user to login. I am using Apache 2.4.9 and this is our current configuration. Apache config file <Location C:/wamp/www/directory> SetHandler form-login-handler AuthFormLoginRequiredLocation https://localNetwork.com/username/TestBed/HTML/login.html AuthFormLoginSuccessLocation https://localNetwork.com/username/TestBed/HTML/test.html AuthFormProvider file AuthUserFile "C:/wamp/passwords" AuthType form AuthName realm Session On SessionCookieName session path=/ SessionCryptoPassphrase secret </Location> And in the login html page I've added that for the user to login <form method="POST" action="/test.html"> User: <input type="text" name="httpd_username" value="" /> Pass: <input type="password" name="httpd_password" value="" /> <input type="submit" name="login" value="Login" /> </form>

  Read the article

• SQL Express 2008 R2 on Amazon EC2 instance: tons of free memory, poor performance

  - by gravyface

  The old SQL Express 2005 was running on a low-end single Xeon CPU Dell server, RAID 5 7200 disks, 2 GB RAM (SBS 2003). I have not done any baseline measurements on the old physical server, but the Web app is used by half a dozen people (maybe 2 concurrently), so I figured "how bad can an Amazon EC2 instance be?". It's pretty horrible: a difference of 8 seconds of load time on one screen. First of all, I'm not a SQL guru, but here's what I've tried: Had a Small Instance, now running a c1.medium (High Cpu Medium) Windows 2008 32-bit R2 EBS-backed instance running IIS 7.5 and SQL Express 2008 R2. No noticeable improvement. Changed Page File from fixed 256 to Automatic. Setup a Striped Mirror from within Disk Management with two attached 1 GB EBS volumes. Moved database and transaction log, left everything else on the boot EBS volume. No noticeable change. Looked at memory, ~1000 MB of physical memory free (1.7 GB total). Changed SQL instance to use a minimum of 1024 RAM; restarted server, no change in memory usage. SQL still only using ~28MB of RAM(!). So I'm thinking: this database is tiny (28MB), why isn't the whole thing cached in RAM? Surely that would speed up performance. The transaction log is 241 MB. Seems kind of large in comparison -- has this not been committed? Is it a cause of performance degradation? I recall something about Recovery Models and log sizes somewhere in my travels, but not positive. Another thing: the old server was running SQL Express 2005. Not sure if that has any impact, but I tried changing the compatibility level from SQL 2000 to 2008, but that had no effect. Anyways, what else can I try here? Seems ridiculous to throw more virtual hardware at this thing. I know I/O is going to be rough on EBS volumes, but surely others are successfully running small .NET/SQL apps on reasonably priced instances?

  Read the article

• How can I solve Windows PPTP VPN issues?

  - by Robin M

  I'm having persistent problems with Windows PPTP VPN connections. The VPN appears up whilst the tunnel won't transfer traffic (ping to a remote IP within the VPN works for a while, and then fails). The client receives routing information via DHCP. When the connection fails, the routing table is still correct so I don't think it's a routing problem. My internet connection is via an ADSL2 line. There's software to deal with PPTP problems, like TunnelRat, but I don't want to install v1.1 of the .NET framework and I'd rather get to the bottom of the problem (I have multiple VPN connections and some are more unreliable than others). What can I do to get to the bottom of this? Alternatively, what can I do to keep the connection alive?

  Read the article

• How come Core i7 (desktop) dominates Xeon (server)?

  - by grant tailor

  I have been using this performance benchmark results to select what CPUs to use on my web server and to my surprise, looks like Core i7 CPUs dominates the list pushing Xeon CPUs into the bush. Why is this? Why is Intel making the Core i7 perform better than the Xeon. Are Desktop CPUs supposed to perform better than server grade Xeon CPUs? I really don't get this and will like to know what you think or why this is so. Also I am thinking about getting a new web server and thinking between the i7-2600 VS the Xeon E3-1245. The i7-2600 is higher up in the performance benchmark but I am thinking the Xeon E3-1245 is server grade. What do you guys think? Should I go for the i7-2600? Or is the Xeon E3-1245 a server grade CPU for a reason?

  Read the article

• Network share permission issues

  - by JL

  I have an IIS server running a site, appPool is running under local system, this is done because its easier to have full permissions to certificates and other file based resources on the local server. Problem is when I try write or copy a file to a network share, permissions are obviously not in place on the remote system for the IIS server local system. Is it possible to grant permissions on the remote system to include read/write or even full access to the IIS servers local system account?

  Read the article

• Display issues on new OpenSUSE install

  - by user1319182

  I installed OpenSUSE 13.1 on my newly built PC, but the display is just horrible : the edges of the screen are missing. For example, I can't see all the top part, I can barely read the date and I see "ctivities" instead of "Activities". However, when I take a screenshot everything seems to be fine (the cursor doesn't appear though) the characters are sometimes too big and sometimes too small the cursor is huge and many other strange things. I took a few pictures I'm using an Intel integrated GPU (HD4400) and made all the possible updates with YaST. Any idea how I can fix this? Thanks

  Read the article

• How come i7 (desktop) dominates Xeon (server)?

  - by grant tailor

  I have been using this performance benchmark results http://www.cpubenchmark.net/high_end_cpus.html to select what CPUs to use on my web server and to my surprise...looks like i7 CPUs dominates the list pushing Xeon CPUs into the bush. Why is this? Why is Intel making the i7 perform better than the Xeon. Are Desktop CPUs supposed to perform better than server grade Xeon CPUs? I really don't get this and will like to know what you think or why this is so. Also i am thinking about getting a new web server and thinking between the i7-2600 VS the Xeon E3-1245. The i7-2600 is higher up in the performance benchmark but i am thinking the Xeon E3-1245 is server grade...so what do you guys think? Should i go for the i7-2600? Or is the Xeon E3-1245 a server grade CPU for a reason?

  Read the article

• windows server 2003 speed issues

  - by farzinSH

  I have a HP server with windows server 2003 and 50 windows XP clients. Since a week and a half the networks speed suddenly drop 2-3 times per day. It gets so slow that none of the clients could work with the HIS program installed on them. We tried so many different things such as replacing the hubs,switches and even some wires. Every time one of these changes solves the problem and the network goes back to its normal state. I checked everything. Even when I disconnected all the clients from the server and connected it to just one computer the problem still remained for 2 hours. I just narrowed down the problem to the couple of likely speculations as follows: viruses? (Updated Kaspersky running on the server shows none) server hardware failure? Physical memory usage on the server? (Because the last time the problem occurred none of the changes above solved the issue so I restarted the server an checked the physical memory usage which was 2 GBs. But I noticed it's increasing over time to over 9 GBs...the server has 16 GBs of RAM.) I surfed the internet and got nothing. Any help would do us a lot....thanks in advance

  Read the article

• Best way to set up servers for .NET performance

  - by msigman

  Assume we have 3 physical servers and let's say we are only interested in performance, and not reliability. Is it better to give each server a specific function or make them all duplicates and split the traffic between them? In other words dedicate 1 as DB server, 1 as web server, and 1 as reporting server/data warehouse, or better to put all three services on each server and use them as web farm?

  Read the article

• mysqld - master to slave replication using rsync innodb, sequence number issues

  - by Luis

  I've read several of the related topics posted here, but I have not been able to avoid this innodb error. The steps I've taken to replicate data from a Slackware server - 5.5.27-log (S) to a FreeBSD slave - 5.5.21-log (F) were these: (S) flush tables with read lock; (S) in another terminal show master status; (S) stop mysqld via command line in third terminal; (F) while both servers are stopped, rsync mysql datadir from (S), excluding master.info, mysql-bin and relay-* files; (F) start mysqld (skip-slave) 121018 12:03:29 InnoDB: Error: page 7 log sequence number 456388912904 InnoDB: is in the future! Current system log sequence number 453905468629. InnoDB: Your database may be corrupt or you may have copied the InnoDB InnoDB: tablespace but not the InnoDB log files. See InnoDB: http://dev.mysql.com/doc/refman/5.5/en/forcing-innodb-recovery.html InnoDB: for more information. This kind of error happens for a lot of tables. I know I can use dump, but the database is large, ca. 70GB and the systems are slow (old), so would like to get this replication to work with data transfer. What should I try to solve this issue?

  Read the article

• Should I host my entire web application using https?

  - by user54455

  Actually my only requirement for using SSL encryption is that when a user logs in, the password is transferred encrypted. However after reading a bit about protocol switching, that an HTTPS session can't be taken over as an HTTP session etc. I've been asking myself if it's so bad to just have the entire application use HTTPS only. What are the reasons against it and how would you rate their importance? Please also mention: How much performance do I lose on server side (roughly)? How much performance do I lose on client side (roughly)? Any other problems on server / client side?

  Read the article

• Debian SMB share having permission issues in windows 7

  - by xxpor

  Hi Everyone, I setup a Debian squeeze server with samba. I then shared my /media directory with the following configuration: [media] comment=Hard Drives read only = no locking = no path = /media guest ok = yes browsable = yes directory mask = 0777 When the drives are mapped in Windows 7, the user can write to all of the subdirectories of media (sdb1, sdc1, etc), but cannot write to any folders that they create themselves in the subdirectories of media. For example, if the user mapped /media/sdb1 to Z:, and then creates a folder Z:\test, the folder is created successfully, but no files can be written to Z:\test. If the user ssh's into the server, they have no problems writing to these directories. I have included the screenshots, in order, of what happens on Windows. This samba share is mounted with ntfs-3g, if it makes a difference. Screenshots are here

  Read the article

• Finding Font Issues in Acrobat

  - by Jayme

  Ok let me try this again, so sorry for not be clear. We create our PDFs through Quark, then send to print. I usually create outlines on my EPS files before I load in Quark but forgot this time. We bypassed the font error that Quark gave us by accident and found out our PDF was bad too late and it cost a lot of money to fix. We are trying to find a way to check our PDF for font problems before we send it to print, in case this problem happens again. We just want to be extra sure that we have tried everything. What I see in Quark is what the font is supposed to look like. When I view my PDF, the text is mixed up. Its readable but doesn't look like its supposed to and the spacing is all off within the text. My boss told me about the preflight in Quark and the Internal Structure for the fonts. She was asking me if this would help and what the lingo all meant. (which is where my first question started) The image on the left is my EPS that is correct, the image on the right is from the PDF. The white text in the top right and the website at the bottom left is what is messed up. I am running Mac 10.5.8, Quark 7.5 and Acrobat 8.3.1. Thanks, Jayme

  Read the article

• Which type of Form factor (motherboard) i should buy and why?

  - by metal gear solid

  If budged is not a problem. I just need best performance with less power consumption. I can purchase any cabinet , power supply and Motherboard. Is Power supply has any relation with Form factor, should i purchase PSU according to Form factor of motherboard? Is the size of motherboard and number of Slots only difference between all form factors? Is there any differences among form factors, related to performance of motherboard? Is bigger in Size (ATX) motherboard always better? Is it so smaller in Size motherboard will consume less power? What are pros and cons of each Form factor? What there are so many Form factor were created?

  Read the article

• Please Help Me Optimize This

  - by Zero

  I'm trying to optimize my .htaccess file to avoid performance issues. In my .htaccess file I have something that looks like this: RewriteEngine on RewriteCond %{HTTP_USER_AGENT} bigbadbot [NC,OR] RewriteCond %{HTTP_USER_AGENT} otherbot1 [NC,OR] RewriteCond %{HTTP_USER_AGENT} otherbot2 [NC] RewriteRule ^.* - [F,L] The first rewrite rule (bigbadbot) handles about 100 requests per second, whereas the other two rewrite rules below it only handle a few requests per hour. My question is, since the first rewrite rule (bigbadbot) handles about 99% of the traffic would it be better to place these rules into two separate rulesets? For example: RewriteEngine on RewriteCond %{HTTP_USER_AGENT} bigbadbot [NC] RewriteRule ^.* - [F,L] RewriteCond %{HTTP_USER_AGENT} otherbot1 [NC,OR] RewriteCond %{HTTP_USER_AGENT} otherbot2 [NC] RewriteRule ^.* - [F,L] Can someone tell me what would be better in terms of performance? Has anyone ever benchmarked this? Thanks!

  Read the article

• What is a proper server for this website

  - by zaidfarekh

  We are using zend framework, doctrine on our website, that will have the minimum of 2000 users daily, please consider that we prefer that the server has opcode caching. And any available technology that speeds up php performance. We have heard that zend server offers an optimal performance for php. Please recommend a hosting server or a vps plan, that can handle such an application. given that our application has some kind of social networking and it applies alot of ajax requests even in minimal usage of the website, for example in 30 min we may have up to 400 requests from an individual user. Thank you in advance

  Read the article

• perfmon.exe itself taking 52.71% of cpu on windows 7 after chrome dies?

  - by jamesmoorecode

  On my Windows 7 machine (build 7100, x64, Dell XPS M1710 laptop), I'm getting horrible performance after chrome crashes. I kill the chrome process from the Resource Monitor, but after that perfmon.exe itself is shown as taking about 50% of the cpu (52.31% right now). Quitting Performance Monitor, then starting it again, shows perfmon starting out with a reasonable CPU, but it quickly (ten seconds) shoots right back up. Suggestions? So far a reboot seems to be the only way to solve the problem. I'm assuming that the perfmon issue is just a symptom of the real problem. (Update, much later: this never got resolved. I'm not seeing the problem in the RTM Win7 + latest Chrome. Yes, it was a core 2 duo, so presumably Chrome was running full blast on one cpu.)

  Read the article

• GTK+ (GTKSharp) poor performance in Windows

  - by nubela

  Hi, In my Mono (C#) project that is meant to be cross-platform, I am using the GTK for the UI. However one thing I noticed is, on my netbook in Archlinux, the performance is really speedy, so events such as mouse hover, and redrawing of widgets, etc, are really fast. Compared to windows (7) on dual core CPUs, the performance is really really weak. Which perplexes me. Am I doing something wrong that is warranting this difference in performance between OSes? What are some ways I can do to optimize GTK on Windows? Its really bad to take around 0.5 secs for a hover event to kick in whereas its almost immediate on a weak(er) netbook with Linux. My code is here for the GUI layer: http://code.google.com/p/subsynct/source/browse/branches/dev/subsync#subsync/GUI Thanks!

  Read the article

< Previous Page | 108 109 110 111 112 113 114 115 116 117 118 119  | Next Page >