Search Results

Search found 13437 results on 538 pages for 'trusted root certificates'.

Page 113/538 | < Previous Page | 109 110 111 112 113 114 115 116 117 118 119 120  | Next Page >

• bonding module parameters are not shown in /sys/module/bonding/parameters/

  - by c4f4t0r

  I have a server with Suse 11 sp1 kernel 2.6.32.54-0.3-default, with modinfo bonding i see all parameters, but under /sys/module/bonding/parameters/ not modinfo bonding | grep ^parm parm: max_bonds:Max number of bonded devices (int) parm: num_grat_arp:Number of gratuitous ARP packets to send on failover event (int) parm: num_unsol_na:Number of unsolicited IPv6 Neighbor Advertisements packets to send on failover event (int) parm: miimon:Link check interval in milliseconds (int) parm: updelay:Delay before considering link up, in milliseconds (int) parm: downdelay:Delay before considering link down, in milliseconds (int) parm: use_carrier:Use netif_carrier_ok (vs MII ioctls) in miimon; 0 for off, 1 for on (default) (int) parm: mode:Mode of operation : 0 for balance-rr, 1 for active-backup, 2 for balance-xor, 3 for broadcast, 4 for 802.3ad, 5 for balance-tlb, 6 for balance-alb (charp) parm: primary:Primary network device to use (charp) parm: lacp_rate:LACPDU tx rate to request from 802.3ad partner (slow/fast) (charp) parm: ad_select:803.ad aggregation selection logic: stable (0, default), bandwidth (1), count (2) (charp) parm: xmit_hash_policy:XOR hashing method: 0 for layer 2 (default), 1 for layer 3+4 (charp) parm: arp_interval:arp interval in milliseconds (int) parm: arp_ip_target:arp targets in n.n.n.n form (array of charp) parm: arp_validate:validate src/dst of ARP probes: none (default), active, backup or all (charp) parm: fail_over_mac:For active-backup, do not set all slaves to the same MAC. none (default), active or follow (charp) in /sys/module/bonding/parameters ls -l /sys/module/bonding/parameters/ total 0 -rw-r--r-- 1 root root 4096 2013-10-17 11:22 num_grat_arp -rw-r--r-- 1 root root 4096 2013-10-17 11:22 num_unsol_na I found some of this parameters under /sys/class/net/bond0/bonding/, but when i try to change one i got the following error echo layer2+3 > /sys/class/net/bond0/bonding/xmit_hash_policy -bash: echo: write error: Operation not permitted

  Read the article

• nginx reload failing: `object version does not match bootstrap parameter`

  - by Jean Jordaan

  I added a server stanza to my virtual.conf, and now nginx seems to have a problem reloading the config. At this point I don't know what exactly is going wrong or how to debug better. Any help would be most appreciated. The config test succeeds: root@server:~# service nginx configtest nginx: the configuration file /etc/nginx/nginx.conf syntax is ok nginx: configuration file /etc/nginx/nginx.conf test is successful I'm tailing the logfile. Upon reload, the following error is logged. As far as I can see, the new config is not used. root@server:~# service nginx reload Reloading nginx: [ OK ] root@server:~# ==> /var/log/nginx/error.log <== nginx object version 0.8.54 does not match bootstrap parameter 1.0.15 at /usr/lib64/perl5/XSLoader.pm line 94. Compilation failed in require. BEGIN failed--compilation aborted. 2012/10/18 12:31:07 [alert] 9620#0: perl_parse() failed: 2 This is the version of nginx I'm running: root@server:~# yum info nginx Loaded plugins: fastestmirror, presto Loading mirror speeds from cached hostfile * base: ftp.udc.es * epel: mirror.nl.leaseweb.net * extras: ftp.udc.es * updates: ftp.cica.es Installed Packages Name : nginx Arch : x86_64 Version : 1.0.15 Release : 2.el6 [...] Server OS: CentOS release 6.3 (Final)

  Read the article

• Duplicate ping packages in Linux VirtualBox machine

  - by Darkmage

  i cant seem t figure out what is going on here. The Linux machine I am using is running as a VM on a Win7 machine using Virtual Box running as a service. If i ping the win7 Host i get ok result. root@Virtual-Box:/home/glennwiz# ping -c 100000 -s 10 -i 0.02 192.168.1.100 PING 192.168.1.100 (192.168.1.100) 10(38) bytes of data. 18 bytes from 192.168.1.100: icmp_seq=1 ttl=128 time=1.78 ms 18 bytes from 192.168.1.100: icmp_seq=2 ttl=128 time=1.68 ms if i ping localhost im ok root@Virtual-Box:/home/glennwiz# ping -c 100000 -s 10 -i 0.02 localhost PING localhost (127.0.0.1) 10(38) bytes of data. 18 bytes from localhost (127.0.0.1): icmp_seq=1 ttl=64 time=0.255 ms 18 bytes from localhost (127.0.0.1): icmp_seq=2 ttl=64 time=0.221 ms but if i ping gateway i get DUP packets root@Virtual-Box:/home/glennwiz# ping -c 100000 -s 10 -i 0.02 192.168.1.1 PING 192.168.1.1 (192.168.1.1) 10(38) bytes of data. 18 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=1.27 ms 18 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=1.46 ms (DUP!) 18 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=22.1 ms 18 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=22.4 ms (DUP!) if i ping other machine on same LAN i stil get dups. pinging remote hosts also gives (DUP!) result root@Virtual-Box:/home/glennwiz# ping -c 100000 -s 10 -i 0.02 www.vg.no PING www.vg.no (195.88.55.16) 10(38) bytes of data. 18 bytes from www.vg.no (195.88.55.16): icmp_seq=1 ttl=245 time=10.0 ms 18 bytes from www.vg.no (195.88.55.16): icmp_seq=1 ttl=245 time=10.3 ms (DUP!) 18 bytes from www.vg.no (195.88.55.16): icmp_seq=2 ttl=245 time=10.3 ms 18 bytes from www.vg.no (195.88.55.16): icmp_seq=2 ttl=245 time=10.6 ms (DUP!)

  Read the article

• How to update-grub on a system running overlayroot?

  - by mikepurvis

  We ship boxes configured with overlayroot, using the following overlayroot.conf: overlayroot=device:dev=/dev/sda6,timeout=20,recurse=0 Which produces the following mount configuration: $ mount overlayroot on / type overlayfs (rw,errors=remount-ro) /dev/sda5 on /media/root-ro type ext3 (ro,relatime,errors=continue,user_xattr,acl,barrier=1,data=ordered) /dev/sda6 on /media/root-rw type ext3 (rw,relatime,errors=continue,user_xattr,acl,barrier=1,data=ordered) /dev/sda1 on /boot type ext3 (rw) As you can see, three key physical partitions: sda1 is /boot, sda5 is a read-only "factory" root, and sda6 is a "user" root which can be wiped at any point to restore the machine to its original factory state. Now, the problem arises when update-grub is run for any reason: $ sudo update-grub [sudo] password for administrator: /usr/sbin/grub-probe: error: cannot find a device for / (is /dev mounted?). Understandable, since / is an overlayfs. The contents of /usr/sbin/update-grub are: #!/bin/sh set -e exec grub-mkconfig -o /boot/grub/grub.cfg "$@" With /usr/sbin/grub-mkconfig being the business part of things. But the actual problem is in /usr/sbin/grub-probe, called by grub-mkconfig, and grub-probe is a binary. So my question is, is there a parameter or whatever which can make grub-probe do the right thing in the face of / being an overlayfs? And secondly, is there a way to hack/patch that in so that the update-grub script just does the right thing? Thanks.

  Read the article

• Why can't I ssh into my server using my private key?

  - by user61342

  I just setup my new server as I used to, and this time I can't login using my private key. The server is ubuntu 11.04. And I have setup following ssh key directories. root@myserv: ls -la drwx------ 2 root root 4096 Sep 23 03:40 .ssh And in .ssh directory, I have done chmod 640 authorized_keys Here is the ssh connection tracebacks: OpenSSH_5.9p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Reading configuration data /etc/ssh_config debug1: /etc/ssh_config line 20: Applying options for * debug1: Connecting to [my.server.ip] [[my.server.ip]] port 22. debug1: Connection established. debug1: identity file /Users/john/.ssh/id_rsa type -1 debug1: identity file /Users/john/.ssh/id_rsa-cert type -1 debug1: identity file /Users/john/.ssh/id_dsa type 1 debug1: identity file /Users/john/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.8p1 Debian-1ubuntu3 debug1: match: OpenSSH_5.8p1 Debian-1ubuntu3 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.9 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA ef:b8:8f:b4:fc:a0:57:7d:ce:50:36:17:37:fa:f7:ec debug1: Host '[my.server.ip]' is known and matches the RSA host key. debug1: Found key in /Users/john/.ssh/known_hosts:2 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password debug1: Next authentication method: publickey debug1: Trying private key: /Users/john/.ssh/id_rsa debug1: Offering RSA public key: /Users/john/.ssh/id_dsa debug1: Authentications that can continue: publickey,password debug1: Next authentication method: password root@[my.server.ip]'s password: Update: I have found the reason but I can't explain it yet. It is caused by uploading the key using rsync -chavz instead of scp, after I used scp to upload my key, the issue is gone. Can someone explain it? Later, I tried rsync -chv, still not working

  Read the article

• apache vhost not working consistently

  - by petrus

  I have a vhost on my webserver whose sole and unique goal is to return the client IP adress: petrus@bzn:~$ cat /home/vhosts/domain.org/index.php <?php echo $_SERVER['REMOTE_ADDR']; echo "\n" ?> This helps me troubleshoot networking issues, especially when NAT is involved. As such, I don't always have domain name resolution and this service needs to work even if queried by its IP address. I'm using it this way: petrus@hive:~$ echo "GET /" | nc 88.191.124.41 80 191.51.4.55 petrus@hive:~$ echo "GET /" | nc domain.org 80 191.51.4.55 router#more http://88.191.124.41/index.php 88.191.124.254 However I found that it wasn't working from at least a computer: petrus@seth:~$ echo "GET /" | nc domain.org 80 petrus@seth:~$ petrus@seth:~$ echo "GET /" | nc 88.191.124.41 80 petrus@seth:~$ What I checked: This is not related to ipv6: petrus@seth:~$ echo "GET /" | nc -4 ydct.org 80 petrus@seth:~$ petrus@hive:~$ echo "GET /" | nc ydct.org 80 2a01:e35:ee8c:180:21c:77ff:fe30:9e36 netcat version is the same (except platform, i386 vs x64): petrus@seth:~$ type nc nc est haché (/bin/nc) petrus@seth:~$ file /bin/nc /bin/nc: symbolic link to `/etc/alternatives/nc' petrus@seth:~$ ls -l /etc/alternatives/nc lrwxrwxrwx 1 root root 15 2010-06-26 14:01 /etc/alternatives/nc -> /bin/nc.openbsd petrus@hive:~$ type nc nc est haché (/bin/nc) petrus@hive:~$ file /bin/nc /bin/nc: symbolic link to `/etc/alternatives/nc' petrus@hive:~$ ls -l /etc/alternatives/nc lrwxrwxrwx 1 root root 15 2011-05-26 01:23 /etc/alternatives/nc -> /bin/nc.openbsd It works when used without the pipe: petrus@seth:~$ nc domain.org 80 GET / 2a01:e35:ee8c:180:221:85ff:fe96:e485 And the piping works at least with a test service (netcat listening on 1234/tcp and output to stdout) petrus@bzn:~$ nc -l -p 1234 GET / petrus@bzn:~$ petrus@seth:~$ echo "GET /" | nc domain.org 1234 petrus@seth:~$ I don't know if this issue is more related to netcat or Apache, but I'd appreciate any pointers to troubleshoot this issue ! The IP addresses have been modified but kept consistent for easy reading. bzn is the server, hive is a working client and seth is the client on which I have the issue.

  Read the article

• Sun-JRE on CentOS-4.8 RPM error: post-install scriptlet failed, exit status 5

  - by Emyr

  I have a server with CentOS 4.8 installed. The provided is rubbish, but there's only a few months left, and they're busy being sued by Chase bank, so I doubt I can get CentOS 5. I wiped the server clean using Virtuozzo, and found that the default image is VERY empty. I even had to install yum myself. I've reached the point where I want to install TomCat. I downloaded the Sun JRE as a .rpm.bin file, did chmod a+x and ran it. That produced a .rpm file, which I tried installing: [root@host java]# rpm -Uvh jre-6u20-linux-i586.rpm Preparing... ########################################### [100%] 1:jre ########################################### [100%] Unpacking JAR files... rt.jar... jsse.jar... charsets.jar... localedata.jar... plugin.jar... javaws.jar... deploy.jar... error: %post(jre-1.6.0_20-fcs.i586) scriptlet failed, exit status 5 [root@host java]# rpm -evv jre-6u20-linux-i586.rpm D: opening db environment /var/lib/rpm/Packages joinenv D: opening db index /var/lib/rpm/Packages rdonly mode=0x0 D: locked db index /var/lib/rpm/Packages D: opening db index /var/lib/rpm/Name rdonly mode=0x0 error: package jre-6u20-linux-i586.rpm is not installed D: closed db index /var/lib/rpm/Name D: closed db index /var/lib/rpm/Packages D: closed db environment /var/lib/rpm/Packages [root@host java]# rpm -qi --scripts jre-6u20-linux-i586.rpm package jre-6u20-linux-i586.rpm is not installed [root@host java]# I couldn't find any results on Google for any parts of that error message, and I have very little experience of rpm (I usually use Debian). Is this a broken package, or am I missing something or some setting?

  Read the article

• error in php not logging or displaying

  - by Grant M

  I can not get any errors to display on screen on write to a log file. When check phpinfo() print out I have same value of master a local for display_errors On display_startup_errors On error_log /var/log/php.log error_reporting E_ALL & ~E_NOTICE log_errors On log_errors_max_len ls -l /var/log/php.log is -rw-rw-rw- 1 root root 0 Jun 21 07:47 /var/log/php.log for /var and /varlog drwxrwxrwx 23 root root 4096 Jun 2 11:13 var when there is an error in the code the page the browsers shows nothing and browser says there is no source for the page. Any suggestions of where else to look or change to errors to appear somewhere (anywhere would be good) edit: my error script is now <?php ini_set('display_errors', 1); error_reporting(E_ALL); echo "print from error.php 2 "; error //print from erroerror to cuase logging to happen. ?> this will print on display and to log Notice: Use of undefined constant error - assumed 'error' in /var/www/piku_dev2/error.php on line 7 but if I put garbage like #@$%$ on the error line I get nor error messages anywhere. Edit2: The problem turned out to in the httpd.conf file. I don't know what it was yet as it was fixed y someone else.

  Read the article

• Boot ISO image from GRUB4DOS on EFI machines

  - by Vladimir Tikhomirov

  I failed with loading ISO image (non-distro) from GRUB2 from USB stick, but found the way how I can boot the GRUB4DOS and then load the image from there. However, it doesn't work all the time and the questions is WHY it doesn't? Environment and loading process: We need to have EFI machine, USB stick, booting ISO, GRUB2 and GRUB4DOS. Last 3 on USB stick. Boot: USB - EFI loader - GRUB2 - GRUB4DOS - ISO image Configuration files To boot GRUB4DOS I use this from grub.cfg: menuentry "image.iso" { linux /syslinux/grub.exe --config-file="/menu.lst" } My menu.lst is here: timeout 20 default 0 title image.iso find --set-root --ignore-floppies --ignore-cd //image.iso map --heads=0 --sectors-per-track=0 //image.iso (hd32) map --hook chainloader (hd32) This works perfectly with Legacy machines. However, when I come to GRUB4DOS, I don't see the menu with image.iso, I see only GRUB command line. That means that my menu.lst didn't load. Why is it like this? Background and ideas I have an idea that GRUB4DOS doesn't recognize my USB stick as a device. I tried the command find and got (hd0,0), (hd0,1), (hd0,2), (rd). When I tried to set root to any of these devices I don't see fat file system, how it was with Legacy machines. The root device is (hd0,0), which has ntfs file system which should be partition with Windows. EFI machines support only GRUB2, so I can't boot GRUB4DOS straight away. Please, don't suggest anything like this, because my image doesn't have kernel. You can imagine that you load HDAT2 or Hiren's boot cd, for example. menuentry "Blancco Blancco5.iso" { set isofile="/image.iso" loopback loop $isofile set root=(loop) linux /isolinux/vmlinuz isofile=$isofile splash quiet initrd /isolinux/initrd }

  Read the article

• User can't SFTP after chroot

  - by Dauntless

  Ubuntu 10.04.4 LTS I'm trying to chroot the user 'sam'. According to all the tutorials out there this should work, but apparently I'm still doing something wrong. The user: sam:x:1005:1006::/home/sam:/bin/false I changed /etc/ssh/sshd_config like this (at the bottom of the file): #Subsystem sftp /usr/lib/openssh/sftp-server # CHROOT JAIL Subsystem sftp internal-sftp Match group users ChrootDirectory %h ForceCommand internal-sftp AllowTcpForwarding no I added sam to the users group: $groups sam sam : sam users I changed the permissions for sam's home folder: $ ls -la /home/sam drwxr-xr-x 11 root root 4096 Sep 23 16:12 . drwxr-xr-x 8 root root 4096 Sep 22 16:29 .. drwxr-xr-x 2 sam users 4096 Sep 23 16:10 awstats drwxr-xr-x 3 sam users 4096 Sep 23 16:10 etc ... drwxr-xr-x 2 sam users 4096 Sep 23 16:10 homes drwxr-x--- 3 sam users 4096 Sep 23 16:10 public_html I restarted ssh and now sam can't log in with SFTP. The session is created, but also closed immediately: Sep 24 12:55:15 ... sshd[9917]: Accepted password for sam from ... Sep 24 12:55:15 ... sshd[9917]: pam_unix(sshd:session): session opened for user sam by (uid=0) Sep 24 12:55:16 ... sshd[9928]: subsystem request for sftp Sep 24 12:55:17 ... sshd[9917]: pam_unix(sshd:session): session closed for user sam Cyberduck says Unexpected end of sftp stream. and other clients give similar errors. What did I forget / what is going wrong? Thanks!

  Read the article

• MaxStartups and MaxSessions configurations parameter for ssh connections?

  - by Webby

  I am copying the files from machineB and machineC into machineA as I am running my below shell script on machineA. If the files is not there in machineB then it should be there in machineC for sure so I will try copying the files from machineB first, if it is not there in machineB then I will try copying the same files from machineC. I am copying the files in parallel using GNU Parallel library and it is working fine. Currently I am copying 10 files in parallel. Below is my shell script which I have - #!/bin/bash export PRIMARY=/test01/primary export SECONDARY=/test02/secondary readonly FILERS_LOCATION=(machineB machineC) export FILERS_LOCATION_1=${FILERS_LOCATION[0]} export FILERS_LOCATION_2=${FILERS_LOCATION[1]} PRIMARY_PARTITION=(550 274 2 546 278) # this will have more file numbers SECONDARY_PARTITION=(1643 1103 1372 1096 1369 1568) # this will have more file numbers export dir3=/testing/snapshot/20140103 find "$PRIMARY" -mindepth 1 -delete find "$SECONDARY" -mindepth 1 -delete do_Copy() { el=$1 PRIMSEC=$2 scp david@$FILERS_LOCATION_1:$dir3/new_weekly_2014_"$el"_200003_5.data $PRIMSEC/. || scp david@$FILERS_LOCATION_2:$dir3/new_weekly_2014_"$el"_200003_5.data $PRIMSEC/. } export -f do_Copy parallel --retries 10 -j 10 do_Copy {} $PRIMARY ::: "${PRIMARY_PARTITION[@]}" & parallel --retries 10 -j 10 do_Copy {} $SECONDARY ::: "${SECONDARY_PARTITION[@]}" & wait echo "All files copied." Problem Statement:- With the above script at some point I am getting this exception - ssh_exchange_identification: Connection closed by remote host ssh_exchange_identification: Connection closed by remote host ssh_exchange_identification: Connection closed by remote host And I guess the error is typically caused by too many ssh/scp starting at the same time. That leads me to believe /etc/ssh/sshd_config:MaxStartups and MaxSessions is set too low. But my question is on which server it is pretty low? machineB and machineC or machineA? And on what machines I need to increase the number? On machineA this is what I can find - root@machineA:/home/david# grep MaxStartups /etc/ssh/sshd_config #MaxStartups 10:30:60 root@machineA:/home/david# grep MaxSessions /etc/ssh/sshd_config And on machineB and machineC this is what I can find - [root@machineB ~]$ grep MaxStartups /etc/ssh/sshd_config #MaxStartups 10 [root@machineB ~]$ grep MaxSessions /etc/ssh/sshd_config #MaxSessions 10

  Read the article

• Create SAMBA node trust relationship to Windows 2003 PDC server

  - by Rod Regier

  I am having problems creating a trust relationship between an OpenVMS/IA64 node running V/IA64 8.3-1H1, TCPIP 5.6 ECO 5, CIFS 1.1 ECO1 PS11 (SAMBA 3.0.28a) and Windows 2003 server running as a PDC. I do have two other OpenVMS/Alpha nodes running V/A 8.3, TCPIP 5.6 ECO 4, CIS 1.1 ECO1 PS10 (SAMBA 3.0.28a) with working trust relationships to the same Windows 2003 server. Looking for assistance in resolving the trust "handshake". \\ Details from failing node. Unless otherwise noted, corresponding files on working nodes are similar or identical. SMB.CONF extract: [global] server string = Samba %v running on %h (OpenVMS) workgroup = WILMA netbios name = %h security = DOMAIN encrypt passwords = Yes name resolve order = lmhosts host wins bcast Password server = * log file = /samba$log/log.%m printcap name = /sys$manager/ucx$printcap.dat guest account = DYMAX print command = print %f/queue=%p/delete/passall/name="""""%s""""" lprm command = delete/entry=%j map archive = No printing = OpenVMS net rpc testjoin [2010/08/13 16:09:28, 0] SAMBA$SRC:[SOURCE.RPC_CLIENT]CLI_PIPE.C;1:(2443) get_schannel_session_key: could not fetch trust account password for domain 'WILMA' [2010/08/13 16:09:28, 0] SAMBA$SRC:[SOURCE.UTILS]NET_RPC_JOIN.C;1:(72) net_rpc_join_ok: failed to get schannel session key from server W2K3AD2 for domain WILMA. Error was NT_STATUS_CANT_ACCESS_DOMAIN_I NFO Join to domain 'WILMA' is not valid net rpc join "-Uaccount%password" tdb_open_isam: error verifying status of file SAMBA$ROOT:[PRIVATE]secrets.tdb tdb_open_isam: errno value = 1 [2010/08/13 16:21:13, 0] SAMBA$SRC:[SOURCE.PASSDB]SECRETS.C;1:(72) Failed to open /SAMBA$ROOT/PRIVATE/secrets.tdb [2010/08/13 16:21:13, 0] SAMBA$SRC:[SOURCE.UTILS]NET_RPC.C;1:(322) error storing domain sid for WILMA tdb_open_isam: error verifying status of file SAMBA$ROOT:[PRIVATE]secrets.tdb tdb_open_isam: errno value = 1 [2010/08/13 16:21:13, 0] SAMBA$SRC:[SOURCE.PASSDB]SECRETS.C;1:(72) Failed to open /SAMBA$ROOT/PRIVATE/secrets.tdb [2010/08/13 16:21:13, 0] SAMBA$SRC:[SOURCE.UTILS]NET_RPC_JOIN.C;1:(409) error storing domain sid for WILMA Unable to join domain WILMA. \\ Example from other node: net rpc testjoin Join to 'WILMA' is OK

  Read the article

• Ubuntu: package installed, but files missing?

  - by jeckyll2hide

  I have been playing around with the /etc/asterisk directory, installing the related pacakge (asterisk-config), removing it, removing the directory manually (just playing around to get the configuration synced to my configuration repo). Now I just want to reinstall the official package, so I do: root@tethys:/etc# apt-get install asterisk-config root@tethys:/etc# tree asterisk/ asterisk/ +-- manager.d What?! Empty?!? Have I installed it? root@tethys:/etc# dpkg --get-selections | grep asterisk asterisk install asterisk-config install asterisk-core-sounds-en install asterisk-core-sounds-en-gsm install asterisk-modules install asterisk-moh-opsound-gsm install asterisk-voicemail install Indeed! Let me check the contents of the package: root@tethys:/etc# dpkg -L asterisk-config ... /etc /etc/asterisk /etc/asterisk/res_snmp.conf /etc/asterisk/dbsep.conf /etc/asterisk/cel_custom.conf /etc/asterisk/cel.conf /etc/asterisk/meetme.conf /etc/asterisk/jingle.conf /etc/asterisk/queuerules.conf ... So, what have I done that the package will get installed, but the contents are nowhere to be seen? And, more importantly, how can I force the contents to be installed, no matter what I have done before?

  Read the article

• How to get the permissions right for /dev/raw1394

  - by Mark0978

  I recently upgraded one of my ubuntu machines to Karmic and I'm having trouble getting the permissions of /dev/raw1394 set to 0666. They only thing this machine is used for is recording audio from a firepod which uses /dev/raw1394 via jackd and there are no other FireWire devices connected, so security around this device is not really an issue. If I run as root, everything works as expected, but I have some folks that run the recorder that I don't want to have root access. However, I can't figure out which lines setup the perms I've tied this: /etc/udev/permissions.d/raw1394.rules:raw1394:root:root:0666 And I have this setup (default install) /lib/udev/rules.d/75-persistent-net-generator.rules:SUBSYSTEMS=="ieee1394", ENV{COMMENT}="Firewire device $attr{host_id})" /lib/udev/rules.d/75-cd-aliases-generator.rules:# the "path" of usb/ieee1394 devices changes frequently, use "id" /lib/udev/rules.d/75-cd-aliases-generator.rules:ACTION=="add", SUBSYSTEM=="block", SUBSYSTEMS=="usb|ieee1394", ENV{ID_CDROM}=="?*", ENV{GENERATED}!="?*", \ /lib/udev/rules.d/60-persistent-storage-tape.rules:KERNEL=="st*[0-9]|nst*[0-9]", ATTRS{ieee1394_id}=="?*", ENV{ID_SERIAL}="$attr{ieee1394_id}", ENV{ID_BUS}="ieee1394" /lib/udev/rules.d/50-udev-default.rules:# FireWire (deprecated dv1394 and video1394 drivers) /lib/udev/rules.d/50-udev-default.rules:KERNEL=="dv1394-[0-9]*", NAME="dv1394/%n", GROUP="video" /lib/udev/rules.d/50-udev-default.rules:KERNEL=="video1394-[0-9]*", NAME="video1394/%n", GROUP="video" /lib/udev/rules.d/60-persistent-storage.rules:KERNEL=="sd*[!0-9]|sr*", ATTRS{ieee1394_id}=="?*", SYMLINK+="disk/by-id/ieee1394-$attr{ieee1394_id}" /lib/udev/rules.d/60-persistent-storage.rules:KERNEL=="sd*[0-9]", ATTRS{ieee1394_id}=="?*", SYMLINK+="disk/by-id/ieee1394-$attr{ieee1394_id}-part%n" And I find these lines in /var/log/syslog Apr 30 09:11:30 record kernel: [ 3.284010] ieee1394: Node added: ID:BUS[0-00:1023] GUID[000a9200c7062266] Apr 30 09:11:30 record kernel: [ 3.284195] ieee1394: Host added: ID:BUS[0-01:1023] GUID[00d0035600a97b9f] Apr 30 09:11:30 record kernel: [ 18.372791] ieee1394: raw1394: /dev/raw1394 device initialized What I can't figure out, is which line actually creates that raw1394 device in the first place. How do you get /dev/raw1394 to have permissions 0666?

  Read the article

• How can I close a port that appears to be orphaned by Xvfb?

  - by Jim Fiorato

  I'm running Xvfb on a FC8 Amazon EC2 image. On occasion Xvfb will crash (unable at the moment to find out the reason for the crash), and after crashing the TCP port will appear to be orphaned. I'm unable to get a PID to kill any process that may be using it. I'm starting Xvfb with: Xvfb :7 -screen 0 1024x768x24 & Examples of what I'm working with are below, the Xvfb port is (was) 6007: # netstat -ap Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 *:ssh *:* LISTEN 1894/sshd tcp 0 0 *:6007 *:* LISTEN - tcp 0 352 ip-10-84-69-165.ec2.int:ssh c-71-194-253-238.hsd1:51689 ESTABLISHED 2981/0 udp 0 0 *:bootpc *:* 1817/dhclient udp 0 0 *:bootpc *:* 1463/dhclient Active UNIX domain sockets (servers and established) Proto RefCnt Flags Type State I-Node PID/Program name Path unix 2 [ ] DGRAM 871 668/udevd @/org/kernel/udev/udevd unix 2 [ ACC ] STREAM LISTENING 5385 1880/dbus-daemon /var/run/dbus/system_bus_socket unix 6 [ ] DGRAM 5353 1867/rsyslogd /dev/log unix 2 [ ] DGRAM 11861 2981/0 unix 2 [ ] DGRAM 5461 1974/crond unix 2 [ ] DGRAM 5451 1904/console-kit-da unix 3 [ ] STREAM CONNECTED 5438 1880/dbus-daemon /var/run/dbus/system_bus_socket unix 3 [ ] STREAM CONNECTED 5437 1904/console-kit-da unix 3 [ ] STREAM CONNECTED 5396 1880/dbus-daemon unix 3 [ ] STREAM CONNECTED 5395 1880/dbus-daemon unix 2 [ ] DGRAM 5361 1871/rklogd # lsof -i COMMAND PID USER FD TYPE DEVICE SIZE NODE NAME dhclient 1463 root 3u IPv4 4704 UDP *:bootpc dhclient 1817 root 4u IPv4 5173 UDP *:bootpc sshd 1894 root 3u IPv4 5414 TCP *:ssh (LISTEN) sshd 2981 root 3u IPv4 11825 TCP ip-10-84-69-165.ec2.internal:ssh->c-71-194-253-238.hsd1.il.comcast.net:51689 (ESTABLISHED) Attempting to force the port closed with iptables doesn't seem to work either. iptables -A INPUT -p tcp --dport 6007 -j DROP I'm at a loss as to how to reclaim/free the port. From what I can tell, this port will remain in this state until the EC2 instance is shut down. So, how can I close this port so I can restart Xvfb?

  Read the article

• Newbie: get access privilege

  - by Mellon

  I am newbie on Linux Ubuntu machine. I logged in to the Ubuntu with username: student. There are some directories only allowed root user to access, for example /var/lib/mysql ,(I know I can use sudo to access but it is not what I want). If I want to get the access privilege on those directories with student account, is it so that I can run the following command : chown student: PATH_TO_ROOT_USER_PRIVILEGED_DIR and after that, I can access that directory by using my own account ? am I right? If I am right, then will root user lose the access privilege because I changed it to student user? If I am wrong, please tell me the right solution. P.S. please don't concern on what I am going to do on /var/lib/mysql directory, that is only my example, as I mentioned above, I mean generally *for those directories which only have root privilege*, can I use chown to change access privilege and will root user then loose the access because of the change made by chown ? I just wanna know the effect of chown.

  Read the article

• How do I Setup Multiple Sites in HostGator Shared Hosting?

  - by cillosis

  I recently decided to consolidate all of my random projects into a single hosting account as it was starting to get very expensive to run each on an individual hosting plan. I purchased the HostGator Baby plan which allows hosting of multiple domains. You have to set it up with a root domain name which is fine (I used my portfolio domain name). As far as file structure, I wanted a folder for each site in /public_html so the structure looks like this: - public_html/ - myportfolio.com/ - ... my files ... - anothersite.com/ - ... my files ... - thirdsite.com/ - ... my files ... I setup add-on domains and pointed them to their respective folders which works fine. My problem is the root domain ex. myportfolio.com expects it's files to be contained at the root of /public_html rather than within it's folder I created. I setup a redirect to point requests for myportfolio.com to myportfolio.com/myportfolio.com/ which works initially except (at least in my WordPress installation) it still references it's root folder as public_html. TL;DR; What is the best way to go about setting up multiple site hosting in a shared hosting environment (i.e. I can't setup vhosts). Does anybody know of any tutorials or videos that walk through this more clearly? Thanks.

  Read the article

• RPM Spec How to specify in package so that previous RPM is removed

  - by user123819

  Question: What do I put in the foo.spec file so that the rpm's will remove the previous rpm before installing? Description: I have created a spec file that creates rpm's for a few packages that use the same source and provide the same service, each with a slightly different configuration. E.g. they each provide the same "capability" Here's an example of the essentials that my .spec file looks like: %define version 1234 %define name foo %define release 1 %define pkgname %{name}-%{version}-%{release} Name: %{name} Version: %{version} Release: %{release} Provides: %{name} %package one Summary: Summary for foo-one Group: %{group} Obsoletes: %{name} <= %{version} Provides: %{name} = %{version} %description one Blah blah blah %package two Summary: Summary for foo-two Group: %{group} Obsoletes: %{name} <= %{version} Provides: %{name} = %{version} %description two Blah blah blah # %prep, %install, %build and %clean are pretty simple # and omitted here for brevity sake %files one %defattr(-,root,root,-) %{_prefix}/%{pkgname} %files two %defattr(-,root,root,-) %{_prefix}/%{pkgname} When I install the first one, it installs ok. I then remove the first one, and then install the second one, that works fine too. I then install the first one, followed immediately by installing the second one, and they both install, one over the other, but, I was expecting that the second one would be removed before installing the second. Example session: # rpmbuild foo and copy rpms to yum repo $ yum install foo-one ... $ yum list installed|grep foo foo-one.noarch 1234-1 @myrepo $ yum install foo-two ...[Should say that it is removing foo-one, but does not]... $ yum list installed|grep foo foo-one.noarch 1234-1 @myrepo foo-two.noarch 1234-1 @myrepo $ rpm -q --provides foo-one foo = 1234 foo-one = 1234-1 $ rpm -q --provides foo-two foo = 1234 foo-two = 1234-1 What do I put in the foo.spec file so that the rpm's will remove the previous rpm before installing? Thank you, .dave.

  Read the article

• phpBB configuration problem under Nginx

  - by zvikico

  Hi, I have a phpBB site running with Nginx (PHP via FastCGI). It works OK. However, some specific actions like moving or deleting a topic fail. Instead, I'm redirected to the forum index. I think it is a problem with the URLs redirection or rewriting. My rewrite rule looks like this: if (!-e $request_filename) { rewrite ^/(.*)$ /index.php?q=$1 last; break; } Any help would be appreciated. My full configuration file is: server { listen 80; server_name forum.xxxxx.com; access_log /xxxxx/access.log; error_log /xxxxx/error.log; location = / { root /xxxxx/phpBB3/; index index.php; } location / { root /xxxxx/phpBB3/; index index.php index.html; if (!-e $request_filename) { rewrite ^/(.*)$ /index.php?q=$1 last; break; } } error_page 404 /index.php; error_page 403 /index.php; error_page 500 502 503 504 /index.php; # serve static files directly location ~* ^.+\.(jpg|jpeg|gif|css|png|js|ico)$ { access_log off; expires 30d; root /xxxxx/phpBB3/; break; } # hide protected files location ~* \.(engine|inc|info|install|module|profile|po|sh|.*sql|theme|tpl(\.php)?|xtmpl)$|^(code-style\.pl|Entries.*|Repository|Root|Tag|Template)$ { deny all; } location ~ \.php$ { fastcgi_pass 127.0.0.1:8888; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME /xxxxx/phpBB3/$fastcgi_script_name; fastcgi_param QUERY_STRING $query_string; fastcgi_param REQUEST_METHOD $request_method; fastcgi_param CONTENT_TYPE $content_type; fastcgi_param CONTENT_LENGTH $content_length; fastcgi_param REMOTE_ADDR $remote_addr; fastcgi_param REMOTE_PORT $remote_port; } }

  Read the article

• HP Storageworks 448 tape drive input/output error with Ubuntu

  - by Dan D

  I'm trying to set a backup to tape of a machine using flexbackup. However any attempt to write to the tape drive (via either flexbackup or just tar) results in "/dev/st0: Input/output error" The machine seems to recognise the drive (HP Storageworks Ultrium 448) and that there's a tape in it and "mt status" seems to work... "mt -f /dev/st0 rewind" or "erase" throw no errors... root@stor001:/# mt status SCSI 2 tape drive: File number=0, block number=0, partition=0. Tape block size 0 bytes. Density code 0x42 (LTO-2). Soft error count since last status=0 General status bits on (41010000): BOT ONLINE IM_REP_EN root@stor001:/# cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: HL-DT-ST Model: DVDRAM GSA-4084N Rev: KS02 Type: CD-ROM ANSI SCSI revision: 05 Host: scsi2 Channel: 00 Id: 03 Lun: 00 Vendor: HP Model: Ultrium 2-SCSI Rev: S65D Type: Sequential-Access ANSI SCSI revision: 03 "tell" does however root@stor001:/# mt -f /dev/st0 tell /dev/st0: Input/output error Based on a forum post I found, I tried: root@stor001:/# dd if=/dev/zero of=/dev/nst0 bs=1024 count=10 10+0 records in 10+0 records out 10240 bytes (10 kB) copied, 5.0815 s, 2.0 kB/s which gave the person on the forum an error but seems to work for me. If anyone has any suggestions, I'm all ears...

  Read the article

• Authenticate users with Zimbra LDAP Server from other CentOS clients

  - by efesaid

  I'am wondering that how can integrate my database,web,backup etc.. centos servers with Zimbra LDAP Server. Does it require more advanced configuration than standart ldap authentication ? My zimbra server version is [zimbra@zimbra ~]$ zmcontrol -v Release 8.0.5_GA_5839.RHEL6_64_20130910123908 RHEL6_64 FOSS edition. My LDAP Server status is [zimbra@ldap ~]$ zmcontrol status Host ldap.domain.com ldap Running snmp Running stats Running zmconfigd Running I already installed nss-pam-ldapd packages to my servers. [root@www]# rpm -qa | grep ldap nss-pam-ldapd-0.7.5-18.2.el6_4.x86_64 apr-util-ldap-1.3.9-3.el6_0.1.x86_64 pam_ldap-185-11.el6.x86_64 openldap-2.4.23-32.el6_4.1.x86_64 My /etc/nslcd.conf is [root@www]# tail -n 7 /etc/nslcd.conf uid nslcd gid ldap # This comment prevents repeated auto-migration of settings. uri ldap://ldap.domain.com base dc=domain,dc=com binddn uid=zimbra,cn=admins,cn=zimbra bindpw **pass** ssl no tls_cacertdir /etc/openldap/cacerts When i run [root@www ~]# id username id: username: No such user But i am sure that username user exist on ldap server. EDIT : When i run ldapsearch command i got all result with credentials and dn. [root@www ~]# ldapsearch -H ldap://ldap.domain.com:389 -w **pass** -D uid=zimbra,cn=admins,cn=zimbra -x 'objectclass=*' # extended LDIF # # LDAPv3 # base <dc=domain,dc=com> (default) with scope subtree # filter: objectclass=* # requesting: ALL # # domain.com dn: dc=domain,dc=com zimbraDomainType: local zimbraDomainStatus: active . . .

  Read the article

• Chef: nested data bag data to template file returns "can't convert String into Integer"

  - by Dalho Park

  I'm creating simple test recipe with a template and data bag. What I'm trying to do is creating a config file from data bag that has simple nested information, but I receive error "can't convert String into Integer" Here are my setting file 1) recipe/default.rb data1 = data_bag_item( 'mytest', 'qa' )['test'] data2 = data_bag_item( 'mytest', 'qa' ) template "/opt/env/test.cfg" do source "test.erb" action :create_if_missing mode 0664 owner "root" group "root" variables({ :pepe1 = data1['part.name'], :pepe2 = data2['transport.tcp.ip2'] }) end 2)my data bag named "mytest" $knife data bag show mytest qa id: qa test: part.name: L12 transport.tcp.ip: 111.111.111.111 transport.tcp.port: 9199 transport.tcp.ip2: 222.222.222.222 3)template file test.erb part.name=<%= @pepe1 % transport.tcp.binding=<%= @pepe2 % Error reurns when I run chef-client on my server, [2013-06-24T19:50:38+00:00] DEBUG: filtered backtrace of compile error: /var/chef/cache/cookbooks/config_test/recipes/default.rb:19:in []',/var/chef/cache/cookbooks/config_test/recipes/default.rb:19:inblock in from_file',/var/chef/cache/cookbooks/config_test/recipes/default.rb:12:in from_file' [2013-06-24T19:50:38+00:00] DEBUG: filtered backtrace of compile error: /var/chef/cache/cookbooks/config_test/recipes/default.rb:19:in[]',/var/chef/cache/cookbooks/config_test/recipes/default.rb:19:in block in from_file',/var/chef/cache/cookbooks/config_test/recipes/default.rb:12:infrom_file' [2013-06-24T19:50:38+00:00] DEBUG: backtrace entry for compile error: '/var/chef/cache/cookbooks/config_test/recipes/default.rb:19:in `[]'' [2013-06-24T19:50:38+00:00] DEBUG: Line number of compile error: '19' Recipe Compile Error in /var/chef/cache/cookbooks/config_test/recipes/default.rb TypeError can't convert String into Integer Cookbook Trace: /var/chef/cache/cookbooks/config_test/recipes/default.rb:19:in []' /var/chef/cache/cookbooks/config_test/recipes/default.rb:19:inblock in from_file' /var/chef/cache/cookbooks/config_test/recipes/default.rb:12:in `from_file' Relevant File Content: /var/chef/cache/cookbooks/config_test/recipes/default.rb: 12: template "/opt/env/test.cfg" do 13: source "test.erb" 14: action :create_if_missing 15: mode 0664 16: owner "root" 17: group "root" 18: variables({ 19 :pepe1 = data1['part.name'], 20: :pepe2 = data2['transport.tcp.ip2'] 21: }) 22: end 23: I tried many things and if I comment out "pepe1 = data1['part.name'],", then :pepe2 = data2['transport.tcp.ip2'] works fine. only nested data "part.name" cannot be set to @pepe1. Does anyone knows why I receive the errors? thanks,

  Read the article

• Member Status: Inquorate in RHEL 5.6

  - by Eugene S

  I've encountered a strange issue. I had to change the time on my Linux RHEL cluster system. I've done it using the following command from the root user: date +%T -s "10:13:13" After doing this, some message appeared relating to <emerg> #1: Quorum Dissolved (however I didn't capture the message completely). In order to investigate the issue I looked at /var/log/messages and I've discovered these errors. Below is the output of few commands I got when tried to investigate the issue, however I don't have enough knowledge to make use of this information. [root@system1a ~]# clustat Cluster Status for system4081 @ Sun Mar 25 11:45:48 2012 Member Status: Inquorate Member Name ID Status ------ ---- ---- ------ chb_sys1a 1 Online, Local chb_sys2a 2 Offline [root@system1a ~]# cman_tool nodes Node Sts Inc Joined Name 1 M 872 2012-03-25 08:43:07 chb_sys1a 2 X 0 chb_sys2a [root@system1a ~]# qdiskd -f -d [17654] debug: Loading configuration information [17654] debug: 0 heuristics loaded [17654] debug: Quorum Daemon: 0 heuristics, 1 interval, 10 tko, 0 votes [17654] debug: Run Flags: 00000035 [17654] info: Quorum Daemon Initializing stat: Bad address [17654] crit: Initialization failed I tried to search through the internet and found out a quite similar issue here. However, for some reason I am not able to access the bug on bugzilla. The link to the bug is here

  Read the article

• Route forwarded traffic through eth0 but local traffic through tun0

  - by Ross Patterson

  I have a Ubuntu 12.04/Zentyal 2.3 server configured with WAN NATed on eth0, local interfaces eth1 and wlan0 bridged on br1 on which DHCP runs, and an OpenVPN connection on tun0. I only need the VPN for some things running on the gateway itself and I need to make sure that everything running on the gateway goes through the VPNs tun0. root:~# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default gw... 0.0.0.0 UG 100 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 br1 192.168.1.0 * 255.255.255.0 U 0 0 0 br1 A.B.C.0 * 255.255.255.0 U 0 0 0 eth0 root:~# ip route 169.254.0.0/16 dev br1 scope link metric 1000 192.168.1.0/24 dev br1 proto kernel scope link src 192.168.1.1 A.B.C.0/24 dev eth0 proto kernel scope link src A.B.C.186 root:~# ip route show table main 169.254.0.0/16 dev br1 scope link metric 1000 192.168.1.0/24 dev br1 proto kernel scope link src 192.168.1.1 A.B.C.0/24 dev eth0 proto kernel scope link src A.B.C.D root:~# ip route show table default default via A.B.C.1 dev eth0 How can I configure routing (or otherwise) such that all forwarded traffic for other hosts on the LAN goes through eth0 but all traffic for the gateway itself goes through the VPN on tun0? Also, since the OpenVPN client changes routing on startup/shutdown, how can I make sure that everything running on the gateway itself loses all network access if the VPN goes down and never goes out eth0.

  Read the article

• ssh keys rejected each day

  - by EddyR

  I've had OpenSSH server running on my debian server for a couple weeks and all of a sudden now when I go to login the next day it rejects my ssh key and I have to manually add a new one each time. Not only that but I have the "tunneling with clear-text passwords" option enabled and the non-root (login with root is disabled) account for that is rejected too. I'm at a loss why this is happening and I can't find any ssh options that would explain it. --update-- I just changed debug level to DEBUG. But before that I'm seeing a lot of the following in auth.log Feb 1 04:23:01 greenpages CRON[7213]: pam_unix(cron:session): session opened for user root by (uid=0) Feb 1 04:23:01 greenpages CRON[7213]: pam_unix(cron:session): session closed for user root ... Feb 1 04:36:26 greenpages sshd[7217]: reverse mapping checking getaddrinfo for nat-pool-xx-xx-xx-xx.myinternet.net [xx.xx.xx.xx] failed - POSSIBLE BREAK-IN ATTEMPT! ... Feb 1 04:37:31 greenpages sshd[7223]: Did not receive identification string from xx.xx.xx.xx ... My sshd_conf file settings are: # Package generated configuration file # See the sshd(8) manpage for details # What ports, IPs and protocols we listen for Port xxx # Use these options to restrict which interfaces/protocols sshd will bind to #ListenAddress :: #ListenAddress 0.0.0.0 Protocol 2 # HostKeys for protocol version 2 HostKey /etc/ssh/ssh_host_rsa_key HostKey /etc/ssh/ssh_host_dsa_key #Privilege Separation is turned on for security UsePrivilegeSeparation yes # Lifetime and size of ephemeral version 1 server key KeyRegenerationInterval 3600 ServerKeyBits 768 # Logging SyslogFacility AUTH LogLevel DEBUG # Authentication: LoginGraceTime 120 PermitRootLogin no StrictModes yes RSAAuthentication yes PubkeyAuthentication yes #AuthorizedKeysFile %h/.ssh/authorized_keys # Don't read the user's ~/.rhosts and ~/.shosts files IgnoreRhosts yes # For this to work you will also need host keys in /etc/ssh_known_hosts RhostsRSAAuthentication no # similar for protocol version 2 HostbasedAuthentication no # Uncomment if you don't trust ~/.ssh/known_hosts for RhostsRSAAuthentication #IgnoreUserKnownHosts yes # To enable empty passwords, change to yes (NOT RECOMMENDED) PermitEmptyPasswords no # Change to yes to enable challenge-response passwords (beware issues with # some PAM modules and threads) ChallengeResponseAuthentication no # Change to no to disable tunnelled clear text passwords PasswordAuthentication yes # Kerberos options #KerberosAuthentication no #KerberosGetAFSToken no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes # GSSAPI options #GSSAPIAuthentication no #GSSAPICleanupCredentials yes X11Forwarding no X11DisplayOffset 10 PrintMotd no PrintLastLog yes TCPKeepAlive yes #UseLogin no #MaxStartups 10:30:60 #Banner /etc/issue.net # Allow client to pass locale environment variables AcceptEnv LANG LC_* Subsystem sftp /usr/lib/openssh/sftp-server UsePAM no ClientAliveInterval 60 AllowUsers myuser

  Read the article

< Previous Page | 109 110 111 112 113 114 115 116 117 118 119 120  | Next Page >