Search Results

Search found 3495 results on 140 pages for 'richard friend'.

Page 114/140 | < Previous Page | 110 111 112 113 114 115 116 117 118 119 120 121  | Next Page >

• Linux Kernel Packet Forwarding Performance

  - by Bob Somers

  I've been using a Linux box as a router for some time now. Nothing too fancy, just enabling forwarding in the kernel, turning on masquerading, and setting up iptables to poke a few holes in the firewall. Recently a friend of mine pointed out a performance problem. Single TCP connections seem to experience very poor performance. You have to open multiple parallel TCP connections to get decent speed. For example, I have a 10 Mbit internet connection. When I download a file from a known-fast source using something like the DownThemAll! extension for Firefox (which opens multiple parallel TCP connections) I can get it to max out my downstream bandwidth at around 1 MB/s. However, when I download the same file using the built-in download manager in Firefox (uses only a single TCP connection) it starts fast and the speed tanks until it tops out around 100 KB/s to 350 KB/s. I've checked the internal network and it doesn't seem to have any problems. Everything goes through a 100 Mbit switch. I've also run iperf both internally (from the router to my desktop) and externally (from my desktop to a Linux box I own out on the net) and haven't seen any problems. It tops out around 1 MB/s like it should. Speedtest.net also reports 10 Mbits speeds. The load on the Linux machine is around 0.00, 0.00, 0.00 all the time, and it's got plenty of free RAM. It's an older laptop with a Pentium M 1.6 GHz processor and 1 GB of RAM. The internal network is connected to the built in Intel NIC and the cable modem is connected to a Netgear FA511 32-bit PCMCIA network card. I think the problem is with the packet forwarding in the router, but I honestly am not sure where the problem could be. Is there anything that would substantially slow down a single TCP stream?

  Read the article

• How to render remote assistance to a person using Live Messenger?

  - by Cheeso

  There is a feature within Windows Live Messenger v9 that allows a person to ask for remote assistance. BBut as I understand it, this works only if the router is UPnP enabled on both ends. Today I tried this with a friend during an active chat session, and nothing happened. I suspect a router problem. as I am remote, I cannot configure the router for them. What's a good way to render remote assistance? Here's the scenario: it will be based on invitation only (it's not a remote desktop or "logmein" situation). It's a younger person, a computer novice, on the other end of the wire. I'll be assiting with their use of applications on the PC. I'd l ike to be able to SEE the screen, and also use the mouse and keyboard. I have used Ultra-Vnc on the target machine and vncviewer on my machine, on a LAN. It works well. But I don't think I can use that, because it's my kids' computer in my ex-wife's place, and I don't want her to accuse me of spying on her computer. That's why I need it to be invitation only. Advice please. Is there an easy way for me to set up Remote Assistance? IS there some other tool I can use?

  Read the article

• What can I do to lower bandwidth cost on a bandwidth heavy site?

  - by acidzombie24

  The easiest answer is CDN but I'd like to ask. A friend of mine has a server that is used for mirror downloads. He says he is doing about 10TB of bandwidth a month which shocked me (I wonder if he is lying). I seen his site and he has no ads. I suspect he might close his website once he gets the bill. Anyways I was wondering since his CPU/RAM is not being used and his HD usage is around 15gb what he can do to lower cost if he continues this site. I said put up ads but I don't know if ads would cover it I found one CDN which offers $0.070 / GB. 10240gb (10TB) * .07 = $717 a month. That seems a little steep but he is using lots of traffic due to it being a mirror site. Also using a CDN doesnt make sense as he doesn't need multiple servers hosting the files in different areas (which is one reason he isn't using that now). He just needs a big upload pipe Is there something he can do? At the moment he is paying $200 a month on a dedicated server and he is using WAY more bandwidth then he should be using. Side question: Can gz-ing files large already compressed files help? like on (zip, rars, etc)

  Read the article

• Cannot Delete Item "Could Not Find This Item" issue

  - by aronchick

  A friend sent a long a file (a .rar) he wanted me to check out for him before he installed it. I downloaded it and unrared it with no problems, but it was full of .exe's instead of the intended contents (fonts) so I advised him to delete it immediately and not use. I then proceeded to do the same, but the folder simply will not delete. Oddly the files went fine, and I never ran anything, but this is what I'm seeing: Could not find this item This is no longer located in C:\Users\This_User\Desktop. verify the item's location and try again. I've tried the following things with no help: Using "Unlocker" to Unlock and delete Using move on reboot and rebooting Using PendMoves (from sysinternals) and rebooting Elevating a cmd line, doing a dir /x to get the short name of the folder, and then del 'shortna~1' Moving the folder to a new folder and then trying to delete the parent folder I'm on Windows 7 RTM, very fresh install. Any thoughts? Update: Just to confirm, I've run Hijack this and half a dozen other malware detectors, and everything came back clean (no extra processes, no other obvious badness). Rebooting in safe mode didn't help either.

  Read the article

• Changing the interface language in Windows 7 Home Premium

  - by Cristián Romo

  A friend of mine has recently purchased a laptop in the U.S. that has Windows 7 Home Premium on it with an English interface. Not being a native English speaker, I'm trying to change the interface language to traditional Chinese. I've looked through the Control Panel in search of something that might let me change the interface language. Naturally, I looked at the Region and Language section and managed to change the formats the computer uses and install a working keyboard, but I haven't found a way to change the interface language. Upon doing some research, I found out that there are two kinds of interface packs, Multilingual User Interface (MUI) and Language Interface Packs (LIP). It seems that MUIs can only be installed through Windows Update, so I looked through the list of updates. To my dismay, the language packs are not present. The optional updates tab doesn't even show up. Many sites show a drop down menu the under Keyboards and Languages tab in the Region and Language options, yet it doesn't show up for me. We also don't have the Windows 7 DVD which might contain this useful file. As far as the LIPs go, I can't find one in Chinese at all, let alone traditional Chinese. Can the interface language be changed in Home Premium at all? If it can, how would I do so?

  Read the article

• How do I troubleshoot a slow hard drive?

  - by Bruce Connor

  My computer is suffering of slow-downs and I'm not surprised (it's around 6 years old). Here's what I've verified: They are not very frequent (only a couple of times a day). When they happen a single application will hang for 10-60 seconds, while the rest don't hang but also get slow. Even as it is happening, the CPU usage stays low. It happens to applications (such as text editor, firefox, skype). It never happens to some applications (such as games) which I use for hours under heavy CPU load. Also of note: The Graphics card and PSU are new (around a year). Though I have a decent amount of software installed right now, this was happening even right after I reinstalled Windows. This HDD has been through many partinioning schemes, and a few heavy operations (such as moving around 200GB of data). Because of the above, I am already 70% sure the problem is with the hard drive. Before I replace it, however, I want to rule out other less likely possibilities (such as RAM, software, or PSU). I don't have the money to replace the entire box right now, but I can easily replace one of the components. I've read several questions (such as this one) which give general guidance on troubleshooting an unknown issue, that is not what I'm looking for here. My main question is: What tests or benchmarks can I run to verify I have a problematic hard drive? I don't need to solve this problem, I am content with just making sure it's the hard drive. I could borrow a newer hard drive from a friend and see if it gets better. A positive result would rule out all other components, but it wouldn't rule out a software issue (since this new hard drive won't have any of the software I use daily). Running on Windows/Linux.

  Read the article

• IE9 will not navigate to some websites but Google Chrome can

  - by Storchburp

  Was recommended by a friend to ask for help here. I am using Internet Explorer 9. As of two days ago I was suddenly unable to navigate to any part of the following websites: www.computerandvideogames.com www.deviantart.com www.cnet.com However I can still access all of them normally through Google Chrome. I am on a college network but these sites are also accessible through fixed terminals provided by the school and are definitely not blocked. I do not know of any other sites similarly affected. There is no popup, no error message, no diversion to a site telling me I can't access / am blocked etc. I can be on www.google.com and attempt to access these sites through the URL or google search, and my cursor will just show the little moving blue wheel next to the arrow for a couple of seconds, and the page displayed on my browser will not change; ie. not navigating at all. Running antivirus software, changing proxy settings in IE, clearing cookies, unplugging/plugging in computer, restarting PC etc have not changed the situation. Any assistance or advice would be greatly appreciated. Thanks in advance.

  Read the article

• Enabling AHCI in BIOS for SSD

  - by Robert

  I am trying to help a friend with a desktop upgrade. It is an old machine with an Intel DG31 main board. The board has 1 IDE port to which a DVD-ROM drive is connected, and 2 SATA ports. 1 SATA port had a hard drive with XP on it. I have made that the secondary drive now and wiped the OS as requested, so it is just for data. The new SSD has been installed but I read that for best results one must enable AHCI in the BIOS? So I checked and in the BIOS there is a SATA Mode setting with 2 options - Native and Legacy. I think Native means AHCI? After setting to Native, I installed Windows 7 Home Premium and all the latest drivers from Intel's website and all Windows Updates. Now when I check Device Manager I see this: Also Microsoft says HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\Msahci\Start and HKEY_LOCAL_MACHINE\System\CurrentControlSet\Services\IastorV\Start should have value 0 for AHCI but I see that the value is 3 for both. So does this mean that Native mode is not AHCI? Or Windows 7 ignored BIOS setting and installed in IDE mode, maybe because both cables are present? Please help me enable AHCI on this system. Thanks!

  Read the article

• Parental Controls in Ubuntu - per user

  - by Hamish Downer

  I would like to set up parental controls on Ubuntu for a friend of mine. I want it so that the child user has the controls set, but the parent user is not restricted. To be clear, they are sharing one computer, so a router based solution won't help. And I would like a set of step by step instructions to do this. Just one way of doing it. I'm an experienced Ubuntu user, happy at the command line. I've spent quite some time googling for this along the way. I hope that the GChildCare project will eventually make this easy, but it is not ready yet. In the meantime, the WebContentControl GUI provides a way of managing parental controls, but apply them to every user on the computer (easy WebContentContol install instructions and detailed instructions, discussion and related links on ubuntuforums). The ubuntuforums post has a FAQ that states that user-specific configuration is not possible with WebContentControl, and then provides 3 links he used to help him do it. But they are far from step by step instructions. There is this thread which is notes along the way and linking to this article about squid and dansguardian. And then to these two dansguardian articles which are somewhat in depth ... So does anyone know of an existing guide to how to set up parental controls on ubuntu with some users not affected? If no one has come up with an answer after a little bit, I'll set up a community wiki answer so we can come up with a guide.

  Read the article

• Give back full control to a user on a disk from another computer

  - by Foghorn

  I have my friend's hard drive mounted externally. After messing with the permissions with TAKEOWN so I could fix some viruses, I have full control over their drive. The problem is, now it's stuck in a "autochk not found" reboot sequence. I think the problem is that the boot sector is invisible to the drive now. So my question is, How can I use icacls to give back the full ownership, when the user I am giving it to is not on my machine? I ran the TAKEOWN command from my windows 7 laptop, their machine is a windows xp Professional with three partitions, I only altered the one that has the boot sector. Here is the permissions that icacls shows: (Where my computer is %System% my username is ME, and the drive is E:\ C:\Users\ME icacls E:\* E:\$RECYCLE.BIN %System%\ME:(OI)(CI)(F) Mandatory Label\Low Mandatory Level:(OI)(CI)(IO)(NW) E:\ALLDATAW %System%\ME:(I)(OI)(CI)(F) E:\alrt_200.data %System%\ME:(OI)(CI)(F) E:\AUTOEXEC.BAT %System%\ME:(OI)(CI)(F) E:\AZ Commercial %System%\ME:(I)(OI)(CI)(F) E:\boot.ini %System%\ME:(OI)(CI)(F) E:\Config.Msi %System%\ME:(I)(OI)(CI)(F) E:\CONFIG.SYS %System%\ME:(OI)(CI)(F) E:\Documents and Settings %System%\ME:(I)(OI)(CI)(F) E:\IO.SYS %System%\ME:(OI)(CI)(F) E:\Mitchell1 %System%\ME:(I)(OI)(CI)(F) E:\MSDOS.SYS %System%\ME:(OI)(CI)(F) E:\MSOCache %System%\ME:(I)(OI)(CI)(F) E:\NTDClient.log %System%\ME:(OI)(CI)(F) E:\NTDETECT.COM %System%\ME:(OI)(CI)(F) E:\ntldr %System%\ME:(OI)(CI)(F) E:\pagefile.sys %System%\ME:(OI)(CI)(F) E:\Program Files %System%\ME:(I)(OI)(CI)(F) E:\RECYCLER %System%\ME:(I)(OI)(CI)(F) E:\RHDSetup.log %System%\ME:(OI)(CI)(F) E:\System Volume Information %System%\ME:(I)(OI)(CI)(F) E:\WINDOWS %System%\ME:(I)(OI)(CI)(F) Successfully processed 22 files; Failed processing 0 files C:\Users\ME

  Read the article

• Can't log in after restoring from Time Machine

  - by Jay Conrod

  My friend uses a Macbook Pro with Snow Leopard 10.6.2. She uses both FileVault and Time Machine to preserve her data. Recently, she suffered a hard disk failure. After restoring from Time Machine using the Snow Leopard install disk, she gets the following error when logging in: You are unable to log in to the FileVault user account at this time. Logging into the account failed because an error occurred. When examining the file system through Terminal, I noticed her home directory is not present: there is no /Users/username directory, or the FileVault .sparsebundle file that's supposed to be there. When using Time Machine.app on /Users, it appears as if her home directory as never there. Additionally, I did a search on the backup disk with the following command: sudo find /Volumes/backup -name '*.sparsebundle' No results. She told me that after working with some large data files, Time Machine would come on, and it would sound like it was transferring a lot of data to the hard disk. Time Machine must have been doing something, right? How can we recover her files? Are they still there?

  Read the article

• Kill a tree, save your website? Content strategy in action, part III

  - by Roger Hart

  A lot has been written about how driving content strategy from within an organisation is hard. And that's true. Red Gate is pretty receptive to new ideas, so although I've not had a total walk in the park, it's been a hike with charming scenery. But I'm one of the lucky ones. Lots of people are involved in content, and depending on your organisation some of those people might be the kind who'll gleefully call themselves "stakeholders". People holding a stake generally want to stick it through something's heart and bury it at a crossroads. Winning them over is not always easy. (Richard Ingram has made a nice visual summary of how this can feel - Content strategy Snakes & ladders - pdf ) So yes, a lot of content strategy advocates are having a hard time. And sure, we've got a nice opportunity to get together and have a hug and a cry, but in the interim we could use a hand. What to do? My preferred approach is, I'll confess, brutal. I'd like nothing so much as to take a scorched earth approach to our website. Burn it, salt the ground, and build the new one right: focusing on clearly delineated business and user content goals, and instrumented so we can tell if we're doing it right. I'm never getting buy-in for that, but a boy can dream. So how about just getting buy-in for some small, tenable improvements? Easier, but still non-trivial. I sat down for a chat with our marketing and design guys. It seemed like a good place to start, even if they weren't up for my "Ctrl-A + Delete"  solution. We talked through some of this stuff, and we pretty much agreed that our content is a bit more broken than we'd ideally like. But to get everybody on board, the problems needed visibility. Doing a visual content inventory Print out the internet. Make a Wall Of Content. Seriously. If you've already done a content inventory, you know your architecture, and you know the scale of the problem. But it's quite likely that very few other people do. So make it big and visual. I'm going to carbon hell, but it seems to be working. This morning, I printed out a tiny, tiny part of our website: the non-support content pertaining to SQL Compare I made big, visual, A3 blowups of each page, and covered a wall with them. A page per web page, spread over something like 6M x 2M, with metrics, right in front of people. Even if nobody reads it (and they are doing) the sheer scale is shocking. 53 pages, all told. Some are redundant, some outdated, some trivial, a few fantastic, and frighteningly many that are great ideas delivered not-quite-right. You have to stand quite far away to get it all in your field of vision. For a lot of today, a whole bunch of folks have been gawping in amazement, talking each other through it, peering at the details, and generally getting excited about content. Developers, sales guys, our CEO, the marketing folks - they're engaged. Will it last? I make no promises. But this sort of wave of interest is vital to getting a content strategy project kicked off. While the content strategist is a saucer-eyed orphan in the cupboard under the stairs, they're not getting a whole lot done. Of course, just printing the site won't necessarily cut it. You have to know your content, and be able to talk about it. Ideally, you'll also have page view and time-on-page metrics. One of the most powerful things you can do is, when people are staring at your wall of content, ask them what they think half of it is for. Pretty soon, you've made a case for content strategy. We're also going to get folks to mark it up - cover it with notes and post-its, let us know how they feel about our content. I'll be blogging about how that goes, but it's exciting. Different business functions have different needs from content, so the more exposure the content gets, and the more feedback, the more you know about those needs. Fingers crossed for awesome.

  Read the article

• POST Fail via AJAX Request?

  - by Jascha

  I can't for the life of me figure out why this is happening. This is kind of a repost (submitted to stackoverflow, but maybe a server issue?). I am running a javascript log out function called logOut() that has make a jQuery ajax call to a php script... function logOut(){ var data = new Object; data.log_out = true; $.ajax({ type: 'POST', url: 'http://www.mydomain.com/functions.php', data: data, success: function() { alert('done'); } }); } the php function it calls is here: if(isset($_POST['log_out'])){ $query = "INSERT INTO `token_manager` (`ip_address`) VALUES('logOutSuccess')"; $connection->runQuery($query); // <-- my own database class... // omitted code that clears session etc... die(); } Now, 18 hours out of the day this works, but for some reason, every once in a while, the POST data will not trigger my query. (this will last about an hour or so). I figured out the post data is not being set by adding this at the end of my script... $query = "INSERT INTO `token_manager` (`ip_address`) VALUES('POST FAIL')"; $connection->runQuery($query); So, now I know for certain my log out function is being skipped because in my database is the following data: if it were NOT being skipped, my data would show up like this: I know it is being skipped for two reasons, one the die() at the end of my first function, and two, if it were a success a "logOutSuccess" would be registered in the table. Any thoughts? One friend says it's a janky hosting company (hostgator.com). I personally like them because they are cheap and I'm a fan of cpanel. But, if that's the case??? Thanks in advance. -J

  Read the article

• PS/2 to USB adapter doesn't work with Model M keyboard

  - by mickburkejnr

  I bought a server about 3 months ago from a friend, and I have only had time to tinker with it in the last week. I noticed that this server doesn't have any PS/2 ports, which meant configuring it was near impossible. I don't have any USB keyboards in the house, I only have an IBM Model M keyboard (built 1994) and another IBM keyboard that was built circa 2001. Both of them have PS/2 connections. I bought an adapter off eBay, and when I used it with the Model M keyboard the three lights on the keyboard flashed for a split second, but then the keyboard is then unresponsive. I can bash away at the keys for ages and nothing will happen. The same applies to the later built IBM keyboard. What could I do to make the adapter work? I am getting the loan of a USB keyboard in two weeks time, but I'd like a more permanent solution without having to rely on getting the loan of a keyboard every time I have to perform maintenance on the server. And as I already have two keyboards which work fine and I like using, I don't really want to have to buy another keyboard just for use on the server.

  Read the article

• Dual Monitor Setup with Ati Radeon Hd 5700 results in unusabledesktop win7

  - by NorthPole

  I have an ATI Radeon HD 5700 card which i've been using under fully updated windows 7 with its latest drivers. My monitor is a 2004 NEC LCD1703M which despite being pretty old runs fine. A friend gave me an IIYAMA ProLite E1900WS monitor (2009 or 20010 ). Both monitors are vga only. I've been using a DLDVI to VGA adapter to connect my old monitor and tested the same adapter to the new monitor and it worked fine. So I bought an HDMI to vga adapter with the purpose of having a dual monitor setup. But when both screens are connected to the card the following problem occurs: The monitor connected to the hdmi port cycles between sleep and a black screen while the other shows the operating system for about two seconds before getting black for another two seconds. I can "use" the computer (move the mouse,click,type e.t.c.) while this happens but its not something pleasant. I tried reinstalling the driver, booting with both screens connected (in which case the powerup messages and the bios are mirrored in both screens until I get to the login screen where everything falls apart) Funny thing is, everything works if I disconnect the ATI graphics card and use the onboard intel one. So, any suggestions as to what might be the problem and how I can fix it?

  Read the article

• IBM Thinkpad 240 - Best way to boot from floppy to USB - Best Linux for 300 MHz 128 MB RAM 800x600 s

  - by zillion

  Mostly I still have that old 'ultraportable' laptop that is mostly like a pre-netbook era laptop and a friend and programmer needs a computer because the one he was using just broke and he has to wait until the new one arrive in 4-6 weeks ... This laptop has no LAN connection and CD-ROM so be prepared for a real challenge! All hardware is well supported on Windows XP (included drivers on the Windows XP CD) and on Linux out-of-the-box (but the screen need a special configuration.) Mostly any Linux that will work well with Skype (USB or regular headset), any MSN client and a text writer for code will do. What I have tested so far: Slitaz 2 don't boot because the floppy of GRUB4DOS don't see the USB drive (fully working and tested on my regular laptop), Damn Small Linux was working but was needing a special screen configuration that I don't remember (in the boot options of the floppy) and now I'm thinking about Puppy Linux that is seen to work totally out of the box with it but I will need an old Puppy version (1 or 2 I think) and the Wakepup floppy ... If you got some ideas to help or to try I'm open!

  Read the article

• Which database to use and system/db administration by layman [closed]

  - by blah

  So my friend and I got briliant ;) idea for a business. Since it is not predictable whether it will work out or not, we decided to keep cost as low as possible to start with, in particular not to hire anyone. If it will work out as expected it will generate enough profit to hire professionals in few months. But for the first few months we'll be doing everything by ourselfs. He's a business/finance major, and I'm a software developer, so obviously I have to take care of IT :) It will be a webapp, written in python/django. My questions regarding this project: 1) What database should I choose? I'm experienced with oracle, and have been working with SQL Server for a while, but both of them are too expensive(at least now). It's a developer experience, I've never done any dba stuff. I'm looking for something free(as in beer). Looks like MySql or PostgreSQL are most popular in this sector. I would appreciate any comments on which db to choose. I'm open to any suggestions(it doesn't have to be MySql or Postgre). Here's what I know about data: It will be almost dates and numbers, a little bit of text. Searched mainly by dates. Data will almost never be updated, mostly inserted and browsed. From 30k to 300k new records/month. 2) Servers. My idea is to rent two dedicated servers. During normal operation one would be a web server(debian/apache), other would be a db server(debian/?). My recovery plan is to install everything on both, and in case of trouble with one of machines just run everything on the other one. Does it even makes sense? Any other tips appreciated. Thanks.

  Read the article

• Computer won't boot from a bootable DVD

  - by JohnB

  My friend gave me his old computer that used to have WinXP on it. I'm trying to load Win7 on it and I thought there was something wrong because it wouldn't boot off a bootable disc, even though I setup the BIOS boot settings properly (I've done this sort of thing a million times). However, this closely related post helped me realize that I can boot off a bootable CD (WinXP), just not a DVD (Win7) Computer won’t boot from CD/DVD drive That might be the answer to my question, however, this motherboard is still pretty current technology. It's a good quality Gigabyte board, and judging from this product page, it came out in 2004. If I can't figure out a solution to my DVD boot problem, I'll have to try something like this: Boot and Install Windows from a USB thumb drive I guess it's possible that this motherboard doesn't allow booting from a DVD, but I still think that I might be missing something. It wouldn't be the DVD rom drive would it? I did try another drive and had the same results. However, I didn't try booting a DVD in the computer that the other test drive came out of, I'll do that later today. Any other advice? Thanks.

  Read the article

• COMPAQ Tower No Signal to monitor

  - by Lancelot

  Hi there, I have had some troubles with this: I received a compaq tower: Compaq Presario SR1224NX Onboard VGA Windows XP SP2 from a friend. It was given to me on condition i give her the files back. My plan was to turn this into an Ubuntu Server. It booted up no problems even with the ubuntu live disc. After a normal shutdown(not unpluggin the power cord and not doing a hard shutdown with the power button), it would not restart even after SEVERAL attempts. I realized the light next to the power supply would flash very rapidly. I researched and found out it was one of two things: a dead power supply or the cables to the motherboard and to the disks etc. Thus i checked to ensure the cables were fine(and they were). I purchased a Power Supply (this one has 400 watts, the initial had 250) and installed it. The tower now boots. It booted into the live disk and everything. After a normal shutdown, it now restarts but is not sending signal to my monitor. I have tried several monitors in which i assure work perfectly but not with this tower(i recall it did show display after replacing the power supply). The monitors are ACER. This is different than most "no Signal" problems since i am not using an external Video Card, this is onboard VGA. Thanks!

  Read the article

• Opening port 80 in router has no results

  - by Ricardo Pieper

  A friend of mine has a ADSL modem and I need to forward some ports. I have already forwarded the 1521 port (Oracle) and it's working fine. Now I need to forward the port 80. I already set up his IIS bindings to this port, and also forwarded the port like this video shows: https://www.youtube.com/watch?v=DLKD-fyexoo So I think I did everything correctly. The local IP address is also the same as the machine where the IIS server is running. I'm sorry, but I can't post images since i don't have 10 points :( Somehow I can't forward this port, yougetsignal.com keeps saying that the door is closed. When I try to open the port, the Control Panel says me that I have to access the control panel in the 8080 port, because the 80 port will be open. Ok, that's fine. But I'm still able to access it in the 80 port, and when I try to access it in the 8080 port, it doesn't work. I'm trying it with the TPLINK 8816, but I also tried to open it in the Opticom DsLink 279, and it didn't worked (using another machine), I got the exact same results. He has a dynamic IP address, but he is also using No-ip, so I can always access his Oracle database in a certain static address. The 1521 port is open. I also tried to disable the firewall in Windows, but that makes no sense to me, since the router doesn't really open the port 80. Clearly I'm missing something. I have never done it in my life, so I dont know how to proceed. Restarting the router was the first I did, no results. I'm accessing his laptop through TeamViewer, so I'm testing the port outside his local network. Edit: My ISP says that they allow to open ports, and the 1521 port is opened. What could I do to open the 80 port?

  Read the article

• No OS will boot, all freeze

  - by Gyan

  This is for a computer with the following configuration: Asus P5KPL-AM/PS motherboard Pentium D 820 (dual core 2.8 GHz) 1 x 2 GB DDR2-800 Transcend RAM 1 SATA2 Samsung 160 GB HDD 1 PATA LG CD/DVD Writer PS/2 generic Keyboard USB Razer mouse The computer was working fine till a month ago with a Hitachi HDD in place of the Samsung. But that drive died and I sent it in for warranty replacement. Since then and till last week, the computer had not been turned on. I then got hold of a spare but XPSP2-loaded Samsung drive from another computer and decided to get this computer temporarily running. However, when I tried to boot into XP, it didn't load. It got stuck at the first graphical screen. When trying Safe Mode, the file list would be updated up to diskio.sys and then freeze. If I tried to boot Kubuntu off a CD, I would get past the first menu, but then get stuck at the subsequent graphical interface in the loading process. A similar thing happend with a friend's Windows XP-on-a-pen-drive. I switched the RAM into the other slot, but no luck. Then I booted the Ultimate Boot CD and ran Memtest86+ and a couple of the bundled CPU stress tests but these detected no errors. Some searching on the Internet brought up the notion of the CPU failing to switch from "real" to "protected mode". I'm hoping to get a fix on what the problem is and what I can do about it. Edit: I've flashed to the latest BIOS, but that doesn't help. Also, Knoppix LiveCD also freezes. I notice that the LED in my mouse goes off at the time of freeze, but trying to boot without the mouse connected produces the same result.

  Read the article

• Java EE at JavaOne - A Few Picks from a Very Rich Line-up

  - by Janice J. Heiss

  A rich and diverse set of sessions cast a spotlight on Java EE at this year’s JavaOne, ranging from the popular Web Framework Smackdown, to Java EE 6 and Spring, to sessions exploring Java EE 7, and one on the implications of HTML5. Some of the world’s best EE architects and developers will be sharing their insight and expertise. If only I could be at ten places at once!BOF4149 - Web Framework Smackdown 2012    Markus Eisele - Principal IT Architect, msg systems ag    Graeme Rocher - Senior Staff Engineer, VMware    James Ward - Developer Evangelist, Heroku    Ed Burns - Consulting Member of Technical Staff, Oracle    Santiago Pericasgeertsen - Software Engineer, Oracle* Monday, Oct 1, 8:30 PM - 9:15 PM - Parc 55 - Cyril Magnin II/III Much has changed since the first Web framework smackdown, at JavaOne 2005. Or has it? The 2012 edition of this popular panel discussion surveys the current landscape of Web UI frameworks for the Java platform. The 2005 edition featured JSF, Webwork, Struts, Tapestry, and Wicket. The 2012 edition features representatives of the current crop of frameworks, with a special emphasis on frameworks that leverage HTML5 and thin-server architecture. Java Champion Markus Eisele leads the lively discussion with panelists James Ward (Play), Graeme Rocher (Grails), Edward Burns (JSF) and Santiago Pericasgeertsen (Avatar).CON6430 - Java EE and Spring Framework Panel Discussion    Richard Hightower - Developer, InfoQ    Bert Ertman - Fellow, Luminis    Gordon Dickens - Technical Architect, IT101, Inc.    Chris Beams - Senior Technical Staff, VMware    Arun Gupta - Technology Evangelist, Oracle* Tuesday, Oct 2, 10:00 AM - 11:00 AM - Parc 55 - Cyril Magnin II/III In the age of Java EE 6 and Spring 3, enterprise Java developers have many architectural choices, including Java EE 6 and Spring, but which one is right for your project? Many of us have heard the debate and seen the flame wars—it’s a topic with passionate community members, and it’s a vibrant debate. If you are looking for some level-headed discussion, grounded in real experience, by developers who have tried both, then come join this discussion. InfoQ’s Java editors moderate the discussion, and they are joined by independent consultants and representatives from both Java EE and VMWare/SpringSource.BOF4213 - Meet the Java EE 7 Specification Leads   Linda Demichiel - Consulting Member of Technical Staff, Oracle   Bill Shannon - Architect, Oracle* Tuesday, Oct 2, 5:30 PM - 6:15 PM – Parc 55 - Cyril Magnin II/III This is your chance to meet face-to-face with the engineers who are developing the next version of the Java EE platform. In this session, the specification leads for the leading technologies that are part of the Java EE 7 platform discuss new and upcoming features and answer your questions. Come prepared with your questions, your feedback, and your suggestions for new features in Java EE 7 and beyond.CON10656 - JavaEE.Next(): Java EE 7, 8, and Beyond    Ian Robinson - IBM Distinguished Engineer, IBM    Mark Little - JBoss CTO, NA    Scott Ferguson - Developer, Caucho Technology    Cameron Purdy - VP Development, Oracle*Wednesday, Oct 3, 4:30 PM - 5:30 PM - Parc 55 - Cyril Magnin II/IIIIn this session, hear from a distinguished panel of industry and open source luminaries regarding where they believe the Java EE community is headed, starting with Java EE 7. The focus of Java EE 7 and 8 is mostly on the cloud, specifically aiming to bring platform as a service (PaaS) providers and application developers together so that portable applications can be deployed on any cloud infrastructure and reap all its benefits in terms of scalability, elasticity, multitenancy, and so on. Most importantly, Java EE will leverage the modularization work in the underlying Java SE platform. Java EE will, of course, also update itself for trends such as HTML5, caching, NoSQL, ployglot programming, map/reduce, JSON, REST, and improvements to existing core APIs.CON7001 - HTML5 WebSocket and Java    Danny Coward - Java, Oracle*Wednesday, Oct 3, 4:30 PM - 5:30 PM - Parc 55 - Cyril Magnin IThe family of HTML5 technologies has pushed the pendulum away from rich client technologies and toward ever-more-capable Web clients running on today’s browsers. In particular, WebSocket brings new opportunities for efficient peer-to-peer communication, providing the basis for a new generation of interactive and “live” Web applications. This session examines the efforts under way to support WebSocket in the Java programming model, from its base-level integration in the Java Servlet and Java EE containers to a new, easy-to-use API and toolset that are destined to become part of the standard Java platform.

  Read the article

• [URGENT HELP PLEASE]USB Flash Drive Problem!

  - by Daren

  Here it goes. My friend saved by his works into my flash drive which was detectable/openable but ... The very next day, the drive wouldn't show up in My Computer and Windows gave him error code 43 (Unknown device). I been searching for the next few hours to find a solution as the works inside is important to him. I know he should back up his files but let's not go there. So .... I tried others few systems that once detected his flash drive but the problem still persisted. I don't know whether or not his flash drive is damaged but when plug/un-plugging, there are still sounds coming out though. Tried solutions: [On Vista Home Premium/HIS COME]Uninstalled -- Restarted com -- Re-installed (ERROR 43) [Windows 7/MY COM] Uninstalled --- Restarted com --- Can't install (ERROR 43) It seems that my com (Windows 7) had the lastest drivers already but still can't detect it. Its a Kingston DataTraveller 101 (DT101) 8GB. Could unplugging the flash drive without clicking "Safely Remove Hardware" is the problem? Kindly provide some help. Thank you all.

  Read the article

• USB Flash Drive Problem!

  - by Daren

  Here it goes. My friend saved by his works into my flash drive which was detectable/openable but ... The very next day, the drive wouldn't show up in My Computer and Windows gave him error code 43 (Unknown device). I been searching for the next few hours to find a solution as the works inside is important to him. I know he should back up his files but let's not go there. So .... I tried others few systems that once detected his flash drive but the problem still persisted. I don't know whether or not his flash drive is damaged but when plug/un-plugging, there are still sounds coming out though. Tried solutions: [On Vista Home Premium/HIS COME]Uninstalled -- Restarted com -- Re-installed (ERROR 43) [Windows 7/MY COM] Uninstalled --- Restarted com --- Can't install (ERROR 43) It seems that my com (Windows 7) had the lastest drivers already but still can't detect it. Its a Kingston DataTraveller 101 (DT101) 8GB. Could unplugging the flash drive without clicking "Safely Remove Hardware" is the problem? Kindly provide some help. Thank you all.

  Read the article

• asterisk extensions.conf & sip.conf

  - by Josh

  I'm trying to get my Dialplan to work. When I call, the only thing I get is a dial tone to enter extension "no Background(thanks-calling) is played". When extension 123 is dialed, busy signal is triggered and asterisk CLI get frozen. Any help will be appreciate it. Conf files below. ; PSTN on sip.conf [pstn] type=friend host=dynamic context=pstn username=pstn secret=password nat=yes canreinvite=no dtmfmode=rfc2833 qualify=yes insecure=port,invite disallow=all allow=ulaw ; PSTN on extensions.conf [pstn] exten => s,1,Answer exten => s,2,Wait,2 exten => s,4,DigitTimeout,5 exten => s,5,ResponseTimeout,10 exten => s,6,Background(thanks-calling) exten => 0,1,Goto(incoming,123,1) ; (Member Services) [incoming] exten => 123,1,NoOP(${CALLERID}) ; show the caller ID info in the console exten => 123,n,Ringing() exten => 123,n,Answer() exten => 123,n,Playback(silence/1) exten => 123,n,Playback(connecting1) exten => 123,n,Wait(3) exten => 123,n,Dial(SIP/line1,60) exten => 123,n,Congestion

  Read the article

< Previous Page | 110 111 112 113 114 115 116 117 118 119 120 121  | Next Page >