Search Results

Search found 3909 results on 157 pages for 'roger light'.

Page 115/157 | < Previous Page | 111 112 113 114 115 116 117 118 119 120 121 122  | Next Page >

• Disk IO slow on ESXi, even slower on a VM (freeNAS + iSCSI)

  - by varesa

  I have a server with ESXi 5 and iSCSI attached network storage(4x1Tb Raid-Z on freenas 8.0.4). Those two machines are connected to each other with Gigabit ethernet. The raid-z volume is divided into three parts: two zvols, shared with iscsi, and one directly on top of zfs, shared with nfs and similar. I ssh'd into the freeNAS box, and did some testing on the disks. I used ddto test the third part of the disks (straight on top of ZFS). I copied a 4GB (2x the amount of RAM) block from /dev/zero to the disk, and the speed was 80MB/s. Other of the iSCSI shared zvols is a datastore for the ESXi. I did similar test with time dd .. there. Since the dd there did not give the speed, I divided the amount of data transfered by the time show by time. The result was around 30-40 MB/s. Thats about half of the speed from the freeNAS host! Then I tested the IO on a VM running on the same ESXi host. The VM was a light CentOS 6.0 machine, which was not really doing anything else at that time. There were no other VMs running on the server at the time, and the other two "parts" of the disk array were not used. A similar dd test gave me result of about 15-20 MB/s. That is again about half of the result on a lower level! Of course the is some overhead in raid-z - zfs - zvolume - iSCSI - VMFS - VM, but I don't expect it to be that big. I belive there must be something wrong in my system. I have heard about bad performance of freeNAS's iSCSI, is that it? I have not managed to get any other "big" SAN OS to run on the box (NexentaSTOR, openfiler). Can you see any obvious problems with my setup?

  Read the article

• It seems Windows 8.1 killed my two T60 laptop batteries

  - by rstock

  Upgraded Windows 7 to Win8 earlier this year, and last week upgraded to Windows 8.1. (Lenovo T60) Had no problem with battery usage when on Win7 nor Win8. After about a week of Win8.1 on my system, the battery stop working, while the system was on. The orange batt. indicator just keeps flashing. The system does not charge the battery (even though I know there was life in it). I installed a known good fully charged battery from another T60, it worked for aboute 40 mins then it instantly died in fron of my eyes. The system now shows the same orange flashing batt. light, but it is not charging. I know both these batteries are still good, they just appear to be dead. My research suggest that the new Win8.1 may not have updated the battery driver to Win8. I have since done that. Same problem. Research i s also pointing me to some 'smart chip' on the batteries that need to a reset. Is this possible ?? Does anyone know a process to reset the 'smart chip' on these batteries (fru# 92P1139) ????

  Read the article

• COMPAQ Tower No Signal to monitor

  - by Lancelot

  Hi there, I have had some troubles with this: I received a compaq tower: Compaq Presario SR1224NX Onboard VGA Windows XP SP2 from a friend. It was given to me on condition i give her the files back. My plan was to turn this into an Ubuntu Server. It booted up no problems even with the ubuntu live disc. After a normal shutdown(not unpluggin the power cord and not doing a hard shutdown with the power button), it would not restart even after SEVERAL attempts. I realized the light next to the power supply would flash very rapidly. I researched and found out it was one of two things: a dead power supply or the cables to the motherboard and to the disks etc. Thus i checked to ensure the cables were fine(and they were). I purchased a Power Supply (this one has 400 watts, the initial had 250) and installed it. The tower now boots. It booted into the live disk and everything. After a normal shutdown, it now restarts but is not sending signal to my monitor. I have tried several monitors in which i assure work perfectly but not with this tower(i recall it did show display after replacing the power supply). The monitors are ACER. This is different than most "no Signal" problems since i am not using an external Video Card, this is onboard VGA. Thanks!

  Read the article

• Maxtor 500GB external hard drive not being detected but power is going to it?

  - by ClarkeyBoy

  I have 2 * Maxtor Onetouch 4 Lite 500GB external hard drives (part no. 9NT2A4-500). They both used to work fine on my old laptop (an Acer) but I have not used them for about a year, since my laptop was stolen and I got this one (also an Acer [Aspire 7738G]). I have one plugged into the mains with one of the leads I believe was supplied with them. It appears to be receiving power as it is warm and the power light (on the unit itself) is on; also the mains adapter is fairly warm. I also have it plugged into my laptop with a USB lead which I have tested on my mp3 player (so I know it works). However my hard drive is not showing on my computer. I have tried checking for new hardware, installing the software that was supplied with it, checking drive letters in case it is registered as C: or something stupid, checking for problems etc... I can't find any cause for it to do this. It does appear to be starting up and, possibly, shutting down and restarting constantly (that's what it sounds like altho I can't be certain). I have had both hard drives stored in different places for the last year and they're both doing the same thing.. if it was only one then I'd guess it had got damaged or corrupted or something but since it is both I doubt this is it. The only things in common with both of them are the leads and the laptop, however I know the USB lead works and guess the mains lead works as there is power going to the unit. Has anyone come across this before or does anyone have any idea what the cause / solution to the problem is? Any help would be greatly appreciated. Regards, Richard

  Read the article

• OS X Hard drive recovery

  - by Adam

  I am trying to recover data from a bad Seagate 1TB hard drive in a 2010 iMac. One day the iMac wouldn't boot (stuck at gray screen on startup). I removed the hard drive from the iMac and connected it to a MacBook using a 3.5" HDD to USB adapter. The hard drive wouldn't mount but it did display in Disk Utility that that there were 2 partitions on the disk. I tried to run Disk Warrior and it showed thousands of errors but still wouldn't mount. At this time the hard drive only show one partition in Disk Utility. Next I tried putting the hard drive in a desktop PC and running Spin Rite - which then gave me several division overflow errors (even with running Spin Rite with a newer version of DOS). The SMART status on the drive reports that the drive has had failures and HD Tune referenced the drive had once hit 59 degrees celsius. Disk Utility gives me the following message when running a pair: Error: Disk Utility can’t repair this disk. Back up as many of your files as possible, reformat the disk, and restore your backed-up files. Overall, the hard drive spins up and sounds OK - there are no clicking noises but the hard drive won't mount and displays as a light gray "Macintosh HD" in disk utility. Any tips or advice on how to recover data on this drive would be GREATLY appreciated! Are there any other tools I can try before calling it quits on this drive? Thank you

  Read the article

• No digital audio output with Asus Xonar DG

  - by Lunatik

  I've purchased an Asus Xonar DG as replacement for faulty onboard audio in a Medion 8822 as it has an optical output which is all I really need to feed my HTPC. I uninstalled the previous drivers/devices, switched the PC off, inserted the Asus card, powered up, disabled the onboard audio in the BIOS, then installed the driver that came on the CD (same version as on Asus' website as of today) and everything went perfectly - no errors. I set the audio devices up in Windows and in the Asus utility (SPDIF enabled, 6-ch audio) as I would expect to see them work, but the only thing is I have no digital audio from test tones within Windows/the Asus utility, PCM audio or Dolby Digital from DVD. Analogue audio is fine. I've uninstalled things and reinstalled a couple of times now, as well as trying almost all combinations of analogue/digital outputs but can't get it sorted. Does anyone have any tips on how to get this working? This card has just been released so there isn't much out there to go on. Notes: The light on the toslink port is lit. OS is Vista 32-bit SP2 and all up to date, pretty much a fresh install with almost no 3rd party applications installed This page seems to suggest that a digital output device in Windows is not needed with Xonar cards as it was with the previous Realtek so I have it set to Analog. The only other output device is S/PDIF pass-thru

  Read the article

• Brick-level backup and restore with exchange 2007

  - by V. Romanov

  In the company I'm working for, we use exchange 2007 and backup it using netbackup. The backup is a daily complete backup of the information store and the direct corollary of this is that restores are hell. We need to restore the entire information store (over 80 gb), somehow merge it back with the original store, which causes problems. Alternatively, we tried using QUEST software to emulate exchange and restore mails from the emulation. However, this proved unreliable. The main problem with this entire situation is that we have to restore the whole information store and walk it through the restore process manually, and its quite absurd to be forced spend more than a day restoring even one erased email. (we have erased mail retention, but sometimes we need to restore older mail). in comparison, back in the day of XCH2003 and backupexec 12, we had complete brick level backup and restore at the push of a button. I've spoken to one of our chief sysadmins who claimed that the official response from microsoft to this issue was - "sorry guys, no brick level backup in XCH2007" which sounds ridiculous to me. Can someone shed some light on the situation? How do you backup your exchange2007 stores? Can you restore a single email quickly? A mailbox, perhaps?

  Read the article

• Kernel hacking methodology - how to find out where to hack the linux kernel

  - by Flavius

  I have a throw-away cheap laptop I'd like to twiddle around, a Thinkpad SL 500. What bothers me are two leds, the one for wireless connectivity, and the one for hibernation, which don't light up at all, although they're functional, I've tried it on windows. So I would like to write a kernel driver for them, nothing big, it just looks like a good idea to play around with the kernel. My question is what methodology should I follow systematically to find out what devices are responsible for those leds (in general, not necessarily specific to my hardware), and what drivers are responsible for the other two leds that work, bluetooth and the battery indicator? And when I say methodology, I really mean the methodology, step by step, with reasons for each step, like in the answer I've gave to someone else over here: What does && mean in void *p = &&abc; I am profficient at fgrepping through big code repositories, using static code analysers & co, but I think my lack of hardware knowledge hinders me on this problem. PS: I'm using ArchLinux, so almost the latest kernel version.

  Read the article

• VMWare Newbie - looking for hardware recommendations and help :) [closed]

  - by Dan

  I am looking for some hardware recommendations on an upcoming virtualization project. We are a small company (80 users - 25 in site 1, 55 in site 2) currently using Windows Server 2003 - no VM servers yet. Our AD is setup where site 1 is the root domain and site 2 is a subdomain/subnet - connected by T1 and VPN for failover. The current DC's also server as file servers, print servers, AntiVirus servers. Email is in the cloud. Additionally then in site 1 we have 3 additional member servers - one running IBM Websphere for a customer specific app, one running Infor PowerLink (no real heavy load) and another that we use for Virtual Studio apps and also runs DirSync for Exchange Online. No heavy workloads on any of these machines really. We also have an AS400 box that we run ERP/CRM software on that site 2 connects to over the WAN link. In site 2 we also have a SQL machine that runs on Win2K server. Database files are not large less than 5 GB. Light to Medium workload on this machine. File servers in each site store less than 500 GB data and probably won't grow to more than 1TB in the next 5 years. I am looking to go to VMWare in both sites and virtualize all servers. What recommendations do you have for server, storage hardware? Is it safe to virtualize all of your DC's? Any help or advice would be greatly appreciated. Thanks.

  Read the article

• Windows, never "lose focus" of the current window

  - by Mazura

  I want the task bar to light up orange and never lose focus to anything. If I'm installing something and then go play a game at some point it will drop out to the finished instillation. Also, if installing multiple programs at once my 'next' button can all of sudden become "click here to install this crappy toolbar" of another program's install. Of course there are settings for some programs to not "lose focus" or "stay on top" but I really want windows to handle it. If its somehow an exe called say, Taskswtich.exe, I could possibly use Process Blocker however I'm assuming its part of a function call or some such. For XP I found this: How to disable auto focus of opened Windows applications? but what about Windows7? And this old post Preventing applications from stealing focus with a bunch of long answers that say "no". I'd appreciate this not being merged with a 4 year old question. I'd like to avoid 3rd party software. This is 2014, don't we know how to hack windows yet?

  Read the article

• Configure Cisco Pix 515 with DMZ and no NAT

  - by Rickard

  I hope that someone could shed some light over my situation, as I am fairly new to PIX configurations. I will be getting a new net for my department, which I am going to configure. At my hands, I have a Cisco PIX 515 (not E), a Cisco 2948 switch (and if needed, I can bring up a 2621XM router, but this is my private and not owned by my dept.). The network I will be getting is the following: 10.12.33.0/26 Link net between the ISP routers and my network will be 10.12.32.0/29 where GW is .1 and HSRP roututers are .2 and .3 The ISP has asked me not to NAT the addresses on my side, as they will set it up to give 10.12.33.2 as a one-to-one nat to a public IP. The rest of the IP's will be a many-to-one NAT to another public IP. 10.12.33.2 is supposed to be my server placed on the DMZ, the rest of the IP's will be used for my clients and the AD server (which is currently also acting as a DHCP server in the old network config with another ISP). Now, the question is, how would I best configure this? I mean, am I thinking wrong here, I am expected to put the PIX first from the ISP outlet, then to the switch which will connect my clients. But with the ISP routers being on a different network, how will the firewall forward the packets to the other network, it's a firewall, not a router. I have actually never configured a pix before, and fortunately, this is more like a lab network, not a production network, so if something goes wrong it's not the end of the world, if though annoying. I am not asking for a full configuration from anyone, just some directions, or possibly some links which will give me some hints. Thank you very much!

  Read the article

• Acer LCD says "no signal"

  - by Ken

  I have an Acer 24" LCD (model "AL2423WDR") that's about 3 years old. It worked perfectly for most of its lifetime so far. Recently it started giving problems. When I turn it on, it either says "no signal" on the display, or the power light goes yellow (as if in power-saving mode). This happens with both DVI and VGA (both of which worked fine before), and stranger still, the 4 buttons on the front, for accessing the on-screen menus, don't do anything. I've also tried different computer hardware and software (PC/Mac, Linux/MacOS), but nothing has worked. I've tried power-cycling it (with both the power button and the power switch), and also unplugging it entirely. The nonworking buttons suggest to me an issue with the firmware. I found a place on Acer's website that says I can send it in to have it fixed, at my expense, but I'll avoid that if I can. Is there a way to fully reset it manually? Or is there something else I can try?

  Read the article

• Cisco Pix 515 ip addressing

  - by Rickard

  I have just gotten my hands on a Cisco Pix 515 (not 515E) with 3 interfaces, and are just about to start some labs. In my lab, I am using a real life scenario from an actual setup at work. As I have no access to the device at work, I am simply trying to replicate the scenario by trial and error. At work, we are given two IP addresses from the provider, which is 1-to-1 nated addresses. The addresses we are allowed to use are: 10.131.35.4-5/29 Now, we have 3 servers on a DMZ, 192.168.2.2-4/24 and 17 client computers on 192.168.1.100-117/24 aswell as some static addressed devices on 192.168.1.8-18/27 My question is, how would I best set up so that the machines on the DMZ get's translated to 10.131.35.4 and the machines on 192.168.1.* will be translated to 10.131.35.5 I don't expect or want anyone to give me a fully functional config, I may learn from it, but I'd prefer to just have some advices or maybe a guide on how to set it up. I hope someone can shed some light over my situation, have been looking through google but I guess I don't the searchwords I'm using isn't too good as I can't find any good clues. THank you very much! PS. Maybe I should add, I am not unfamiliar with the Cisco CLI, as I prefer using that before any gui's. So not really looking for any solutions for the ASDM. DS.

  Read the article

• Windows XP can use a wired network port, but MacBook (OS X) fails on the same port

  - by Dean Hill

  I wired the Cat5 in my house seven years ago. The wired ports have worked fine with both my Windows XP laptop and MacBook. My wireless network also works fine, but I like to use wired occasionally. One of the Cat5 runs wasn't terminated with a jack, so I recently terminated this wire with a port/jack on the wall end and a standard Cat5 plug on the end that plugs into my router. This is the same setup as my other runs. Unfortunately, the MacBook isn't working well with the new wired port. The OS X Network System Preferences show the IP, Subnet, Router, etc., and everything looks fine. A "netstat -ibd" shows no errors or dropped packets. However, when I open a page in Safari, the status says "Contacting 'www.google.com'" and appears to hang. If I wait for a couple minutes, part of the Google page starts to display, but it is still not the full page load. When I use a Windows XP laptop on the same wired port, everything works fine. An internet speed test shows good results and all web pages load fine. A "netstat -e" under Windows shows no errors. I've used a Cat5 tester, and the cable tests fine (wires 1-8 light up in sequence). I've replaced both the port/jack and the connector twice to make sure I wired things correctly. I'd really like this Cat5 to work with the MacBook (and I'm trying to avoid running a new length of cable). Any ideas what the problem could be?

  Read the article

• PC won't boot after hanging during Windows 8 automatic repair [closed]

  - by Mun

  I've got a custom built PC using an ASUS P5E motherboard and Intel Q6600 CPU. I plugged in my mp3 player to the USB port yesteday, and when I came back to the machine after about an hour or so, the Windows 8 automatic repair message was on the screen. It seemed to stick there for an hour, after which I decided to just hit reset and try and figure out what was going on. However, the machine rebooted to a black screen before even getting to the BIOS, with the monitor lights just blinking indicating there was no signal. Tried powering down completely, waiting a few minutes and then powering back up again with no difference; black screen with monitor lights blinking. Tried leaving it on for a while and then pinging from another machine or accessing it via something like LogMeIn, but everything showed the machine as being offline. There were also no error beeps or anything like that. Also tried unplugging all of the memory and rebooting and that also caused no error beeps. Removed one of the display cards and left the other one in there, and still only a black screen. I'm inclined to think that the motherboard or CPU is fried, but there is no indication of damage on any components and the CPU fan seems to be working fine as it always has, so overheating seems unlikely. It's also plugged into a surge protector. The motherboard also has a green light which still lights up. As everything was still working fine before hitting the reset button during Windows 8 automatic repair screen, at which point everything stopped working, it seems unlikely that this problem is down to component failure. Has anyone else experienced anything like this or have any ideas on what could be causing this behavior?

  Read the article

• MySQL Workbench is not finding MySQL service? [closed]

  - by PhADDinTraining

  I set up a local MySQL server, currently with no databases. I'm trying to create a new server instance profile in MySQL Workbench to manage the server, and during the Create New Server Instance Profile wizard, it gets to the Windows Management section and tells me that No MySQL service found. I went into Task Manager and found the process mysqld.exe to be running, under the user name of NETWORK SERVICE. Then I went into the Services tab and found that MySQLServerName (I custom named the Windows service) is also there, and status is running. I ran cports and looked at what ports mysqld.exe is using, and ran a telnet command on that port. It's reporting that the port is being listened in on. I then ran the MySQL Command Line Client to be sure, and after \r it gives me a proper connection ID and a list of databases (NONE at this point). But with all this, I can't make the wizard find a running service. I've Googled this and found no answers, so please, if someone would help shed some light on this issue that'd be great!

  Read the article

• Ubuntu server or Debian server (to run C++ apps developed on Ubuntu)

  - by skyeagle

  I have written a number of C++ server side daemons for my website, using my Ubuntu 9.10 dev machine. The C++ apps I mentioned above are "GUI-less" daemons (and libraries used by the daemons). I am now about to host my website and need to decide whether to go with Debian server or Ubuntu server. In a nutshell, here is the situation: I developed on Ubuntu desktop because I preferred the more friendly GUI I would like to deploy on Debian Server because of the (perceived?) robustness of the Debian server over Ubuntu server (I may be totally wrong here - and in fact, this is really what this question is all about) If Debian server is indeed more robust than Ubuntu server, then I have no choice but to go with Debian server - BUT, will my Ubuntu developed C++ apps run on the server? (or do I need to recompile them on the server? (I'd HATE to have to do this, because I want to keep the server machine clean and light - no GUI, no dev tools etc). This last question is really about binary compatability between Ubuntu and Debian. I want the server to be robust, secure and stable, and simply act as a server (i.e. LAMP and very little else - no GUI etc). Given that requirement, and the fact that I need to run my C++ apps (developed on Ubuntu 9.10), I need advice on which OS to choose for the server. Ideally, any advice will be backed with a reason. I am particularly interested in hearing from people who have been in an identical situation, or done something similar.

  Read the article

• Looking for equivalent of ProxyPassReverseMatch in Apache to fix missing trailing forward slash issue

  - by Alex Man

  I have two web servers, www.example.com and www.userdir.com. I'm trying to make www.example.com as the front end proxy server to serve requests like in the format of http://www.example.com/~username such as http://www.example.com/~john/ so that it sends an internal request of http://www.userdir.com/~john/ to www.userdir.com. I can achieve this in Apache with ProxyPass /~john http://www.userdir.com/~john ProxyPassReverse /~john http://www.userdir.com/~john The ProxyPassReverse is necessary as without it a request like http://www.example.com/~john without the trailing forward slash will be redirected as http://www.userdir.com/~john/ and I want my users to stay in the example.com space. Now, my problem is that I have a lot of users and I cannot list all those user names in httpd.conf. So, I use ProxyPassMatch ^(/~.*)$ http://www.userdir.com$1 but there is no such thing as ProxyPassReverseMatch in Apache. Without it, whenever the trailing forward slash is missing in the URL, one will be directed to www.userdir.com, and that's not what I want. I also tried the following to add the trailing forward slash RewriteCond %{REQUEST_URI} ^/~[^./]*$ RewriteRule ^/(.*)$ http://www.userdir.com/$1/ [P] but then it will render a page with broken image and CSS because they are linked to http://www.example.com/images/image.gif while it should be http://www.example.com/~john/images/image.gif. I have been googling for a long time and still can't figure out a good solution for this. Would really appreciate it if any one can shed some light on this issue. Thank you!

  Read the article

• Debugging a Drobo that chokes Windows 7x64 When Plugged In

  - by Pridkett

  I've had a love hate relationship with my Drobo for a long time. After two years of using it on a Linux box, I moved it over to a Windows 7 machine where it seemed to work just fine for a long time, but it was under very light usage. Mainly backups that never actually happened. Recently I began using it for additional backup services (through CrashPlan, which is great). This means the Drobo gets a lot more usage. Also it means that something interesting happens, the Drobo can choke my system on startup. Here's what I mean: Start computer without Drobo plugged in, CrashPlan and Drobo Dashboard services disabled: 105s Start computer with Drobo plugged in Crashplan disabled, Drobo Dashboard enabled: 250s (and 1 cpu at 100% for a very long time, drobo churning) Start computer with Drobo plugged in, CrashPlan and Drobo Dashboard disabled: 250s (1 cpu at 100% for a very long time, drobo churning) Start computer with Drobo plugged in, Crashplan and Drobo Dashboard enabled: 300s (1 cpu at 100% for a very long time, drobo churning) If I yank the USB plug on the Drobo the CPU usage goes down to nothing very quickly. The slow startup in the fourth scenario is because CrashPlan is trying desperately to load stuff up on the H: drive before it gives up, so I've disabled it for the time being. So here's my question: What the heck is going on when I plug the drobo in? I've fired up Process Explorer and see that the System process is hogging the CPU, specifically it's an ntoskrnl.exe/KdPollBreakIn thread that's going ape. Is this something that's wrong with Drobo? Windows? Any idea on how to find out? If it matters, here's tech info: Athlon 64x2 4400, 2GB RAM, Win7 Ultimate, Drobo USB (2x1TB, 2x320GB)

  Read the article

• Simulate SNMP traps to test surveillance

  - by jishi

  I'm trying to use Net-SNMP on Windows to emulate a trap that should trigger an alarm on our surveillance system. This is the setup: Windows 7 client that sends the trap Net-SNMP as software for sending the trap Linux with Adventnet ManageEngine OpManager as NMS (not relevant) This is what I'm trying to accomplish send trap with OID .1.3.6.1.4.1.5089.1.0.1 (according to the MIB I have loaded into my NMS) and just some sort of message into it to see if I can get any alarm in my NMS. I can see that I actually send a trap in my firewall, but I have no idea what it contains. This is my attempt so far: snmptrap.exe -v 2c -c xxxxxxx 192.168.100.65 '' 6 0 .1.3.6.1.4.1.5089.1.0.1 s "123456" However, I can't seem to find any reasonable documentation with examples for snmptrap. Basically, I need to know what: '' <- why do I need this? I can omit it and it will still send a trap 6 <- Enterprise gneric trap, I assume. Is this correct? 0 <- I have no idea, I need some sort of value for this .1.3.6.1.4.1.5089.1.0.1 <- the enterprise specific OID I assume, should this be followed by some more numbers s <- indicates string "123456" <- just a random test-string... This doesn't make much sense to me, and if anyone can shed some light on this I would be very grateful.

  Read the article

• "Server Unavailable" and removed permissions on .NET sites after Windows Update [closed]

  - by andrewcameron

  Our company has five almost identical Windows 2003 servers with the same host, and all but one performed an automatic Windows Update last night without issue. The one that had problems, of course, was the one which hosts the majority of our sites. What the update appeared to do was cause the NETWORK user to stop having access to the .NET Framework 2.0 files, as the event log was complaining about not being able to open System.Web. This resulted in every .NET site on the server returning "Server Unavailable" as the App Domains failed to be initialise. I ran aspnet_regiis which didn't appear to fix the problem, so I ran FileMon which revealed that nobody but the Administrators group had access to any files in any of the website folders! After resetting the permissions, things appear to be fine. I was wondering if anyone had an idea of what could have caused this to go wrong? As I say, the four other servers updated without a problem. Are there any known issues involved with any of the following updates? My major suspect at the moment is the 3.5 update as all of the sites on the server are running in 3.5. Windows Server 2003 Update Rollup for ActiveX Killbits for Windows Server 2003 (KB960715) Windows Server 2003 Security Update for Internet Explorer 7 for Windows Server 2003 (KB960714) Windows Server 2003 Microsoft .NET Framework 3.5 Family Update (KB959209) x86 Windows Server 2003 Security Update for Windows Server 2003 (KB958687) Thanks for any light you can shed on this.

  Read the article

• CUPS causes printer to click and doesn't print

  - by Pez Cuckow

  I'm suffering a strange problem with my Cannon iP4850 when trying to use CUPS on a Raspberry Pi (this is not RPi specific, please do not vote to move it). When I plug the printer into my Laptop (OSX) or my Desktop W7 it identifies as a iP4800 and prints perfectly. So I plug it into the Pi (running debian), set it up in CUPS enable sharing and can now see the iP4800 series shared on the network. However if I print to it (using AirPrint etc...); the file gets to CUPS safely (shows in the queue) but when it tries to print the printer clicks (like a loud thunk) 3/4 times and then gives in, with a double amber flashing light. In cups it shows as job completed. Do you know why using the pi and cups would cause what appears to be a hardware fault and what I can do to fix the problem or to provide further debug info? Thanks for your time! Description: Canon iP4800 series Location: Lounge Driver: Canon PIXMA iP4800 - CUPS+Gutenprint v5.2.9 (color, 2-sided printing) Connection: usb://Canon/iP4800%20series?serial=2239B2 Note: I've tried deleting and re-adding the printer to the Laptop, Desktop and PI and the results are always the same Log for plugging in printer and printing (attempting to) something until the printer turned off again pi@pezpi /var/log $ dmesg [ 7284.176336] usb 1-1.2: new high speed USB device number 8 using dwc_otg [ 7284.279703] usb 1-1.2: New USB device found, idVendor=04a9, idProduct=10d5 [ 7284.279750] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 7284.279771] usb 1-1.2: Product: iP4800 series [ 7284.279786] usb 1-1.2: Manufacturer: Canon [ 7284.279800] usb 1-1.2: SerialNumber: 2239B2 Setting cups to verbose: Change loglevel in cupsd.conf to debug (or debug2) pi@pezpi /var/log $ sudo vim /etc/cups/cupsd.conf pi@pezpi /var/log $ sudo /etc/init.d/cups restart [ ok ] Restarting Common Unix Printing System: cupsd. pi@pezpi /var/log $ Log from $ /var/log/cups/error_log is at http://pastebin.com/7VZMRMrG (too large to post here) The log contains - in order (deleted the log and then did the beneath) Restarting the cups server Attempting to print a test page x2 Printing from 192.168.1.90 via AirPrint Printing from 192.168.1.90 via Network Print Turning the printer off and on again

  Read the article

• What does this strange network/subnet mask mean?

  - by dunxd

  I'm configuring a new ASA 5505 for deployment as a VPN endpoint in a remote office. After configuring it and connecting the VPN, I get the following messages: WARNING: Pool (10.6.89.200) overlap with existing pool. ERROR: IP address,mask <10.10.0.0,93.137.70.9> doesn't pair 10.6.89.200 is the address I configured for the ASA. It has the subnet mask 255.255.255.0. The ip address 10.10.0.0 corresponds to one of our subnets, but it certainly wouldn't have a subnet mask of 93.137.70.9. That looks more like a public IP address (and resolves to an ADSL connection somewhere). I am sure if we had such a subnet configured, that it would indeed overlap with 10.6.89.200. There is no reference to 93.137.70.9 in the config of this ASA or our head office ASA. Can anyone shed light on what is going on here? The sudden appearance of a strange subnet mask is a bit alarming.

  Read the article

• Mail to Mailenable group sometimes bounces back because it cannot find one of the group members

  - by Stanley

  I am using MailEnable Enterprise Edition 6.53. On one of my PostOffices I have a group address set up with 5 members in the group. Under normal circumstances when someone sends a mail to this group then the mail gets successfully forwarded to all 5 members in the group. However, every now and then when a recipient sends to the group they get a bounce back message from us that the mail could not be delivered because one of the user's addresses was not found on the server. This could happen for any one of the 5 users in the group. The error message looks like: Message could not be delivered. Error was: The email address is not available on this system The following recipient(s) could not be reached: [SF:mydomain.com/my_username] What could be causing this and how do I fix it? Obviously the mailbox DOES exist as, under normal circumstances, when someone mails the group the mail gets delivered successfully and forwarded to all group members. All the mailboxes most definitely DO exist on the system. EDIT: I have done more investigation and I see an error in Windows Event Viewer: MailEnable Database Provider error: 0 FAILURE: (SQLDriverConnect), Module: MEIMAPS.exe; Error: [Microsoft][ODBC SQL Server Driver]Timeout expired This seems to be related to http://forum.mailenable.com/viewtopic.php?p=53157 and http://www.mailenable.com/kb/content/view.asp?ID=ME020535 but the setups in these links use MySQL as a database whereas we use SQL Server. Maybe this shines some new light on the problem?

  Read the article

• Why can't I boot in to Windows Recovery Environment to fix my HDD or salvage my data?

  - by Kevin

  I've been trying to get in to WindowsRE to salvage the files on my Sony Vaio laptop after it failed to load Vista (it finally, consistently displays "Error loading operating system" after months of such intermittent failures, usually rectified via restarts or utilizing Startup Repair or CHKDSK from WindowsRE) . The problem is, after successfully accessing it once after this failure (and many times before over the course of the laptop's life), I can no longer get it to load. During the last successful access (right after the failure), I ran startup repair, which itself failed and notified me that the boot sector was corrupt. I attempted to head in to Sony's proprietary recovery tools menu, which is accessible from WindowsRE when it is loaded from the recovery partition or recovery disk, however it hung. I have since been unable to access the recovery environment after restarting, using any of these methods: Access via the recovery partition (pressing F10 on boot) Access via recovery DVD (created using the same computer when it was healthy) Access via a Windows Vista installation DVD All three methods produce the same results: The computer acknowledges the boot attempt The computer successfully gets passed the "Windows is loading files" screen The computer successfully gets passed the Windows loading screen The computer then stalls at a black screen, while showing HDD activity (via indicator light). After a few minutes, the HDD activity ceases, and after a few more minutes, the over sized cursor that is utilized in WindowsRE appears on the black screen. The actual recovery environment, however, never appears, even after leaving the computer in such a state overnight. What is fustrating is that other bootable utilities, such as SeaTools for DOS and MemTest, boot up and run fine. In running perfectly normally, MemTest was able to produce a plethora of errors utilizing my RAM. I'm inclined to believe the RAM's faultiness may causing the WindowsRE booting to fail. Would this be a valid assumption? If I'm not mistaken, booting from external media utilizes the RAM, so such a reason is plausible, assuming my knowledge of bootloading is correct. Other than that, I can't figure out any reason why all the bootable utilities except WindowsRE run fine. Does anyone know what the problem is, or could be? Any solutions?

  Read the article

< Previous Page | 111 112 113 114 115 116 117 118 119 120 121 122  | Next Page >