Search Results

Search found 21369 results on 855 pages for '128 bit'.

Page 116/855 | < Previous Page | 112 113 114 115 116 117 118 119 120 121 122 123  | Next Page >

  • TCP Tweaking options and Results: Any suggestions?

    - by krishnakumar
    I first tried with the default windows XP TCP option(It doesn't have TCPWindowSize option and TCP1323 in its Registry setting). I dynamically set those options using TCP optimizer. Here I list out the result with and without TCP Tweaking option. I see no major improvements in TCP after increasing window size optimally too. What value should I set to increase the performance? Results: Without any window size and MTU setting from server to client (receiving) TCPWindowSize : MTU : TTL: Size:586 MB total duration : 03:47 With window size extension from server to client (receiving) Bandwidth :100 Mbps Latency: 100ms BDP :1250000 TCPWindowSize : 1250000 MTU :1500 TTL:128 Size:586MB total duration : 03:44 With window size extension from server to client (receiving) TCPWindowSize :64240 MTU :1500 TTL :112 Size: 586MB total duration : 03:49

    Read the article

  • Browsers ignoring hosts file

    - by madkris
    Until recently my browsers started to ignore my hosts file. I have Windows 7 operating system installed. 192.168.0.5 livesite.com I have tried: Clearing browser cache Issued "ipconfig /flushdns" from the command line Issued "ping livesite.com" from the command line (response was "Reply from 192.168.0.5: bytes=32 time=1ms TTL=128") Restarting unit Backing up original hosts file and making a new one Checking lmhosts.sam (everything is commented out) Connecting directly to modem using cable Checked \HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\DataBasePath Tried it on another laptop with exactly the specs as I have Then I tried Changing entry to "127.0.0.1 livesite.com" (ping ok, browser ok) Changing entry to "192.168.0.5 livesite.com" (ping ok, browser ok but only for a sec) Issued "ipconfig /flushdns" from the command line (ping ok, browser not ok) Changing entry to "127.0.0.1 livesite.com" (ping ok, browser ok) Changing entry to "192.168.0.5 livesite.com" (ping ok, browser not ok) Issued "ipconfig /flushdns" from the command line (ping ok, browser not ok) Any idea why it worked for a moment? Or better yet anything I havent tried or some error I may have overlooked?

    Read the article

  • Browsers ignoring hosts file

    - by madkris
    Until recently my browsers started to ignore my hosts file. I have Windows 7 operating system installed. 192.168.0.5 livesite.com I have tried: Clearing browser cache Issued "ipconfig /flushdns" from the command line Issued "ping livesite.com" from the command line (response was "Reply from 192.168.0.5: bytes=32 time=1ms TTL=128") Restarting unit Backing up original hosts file and making a new one Checking lmhosts.sam (everything is commented out) Connecting directly to modem using cable Checked \HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\DataBasePath Tried it on another laptop with exactly the specs as I have Then I tried Changing entry to "127.0.0.1 livesite.com" (ping ok, browser ok) Changing entry to "192.168.0.5 livesite.com" (ping ok, browser ok but only for a sec) Issued "ipconfig /flushdns" from the command line (ping ok, browser not ok) Changing entry to "127.0.0.1 livesite.com" (ping ok, browser ok) Changing entry to "192.168.0.5 livesite.com" (ping ok, browser not ok) Issued "ipconfig /flushdns" from the command line (ping ok, browser not ok) Any idea why it worked for a moment? Or better yet anything I havent tried or some error I may have overlooked?

    Read the article

  • aligning truecrypt partition on 1.5TB 4kB sector drive

    - by pQd
    hi, aligning partitions to start at real physical sector of ssds / stripped raids / 4kB drives is a 'good thing to do'. but i've run into a problems when trying to do it for a truecrypt partition that will contain ext3 on it. or so it seems. when drive is question is partitioned properly and formatted with ext3 i get very reasonable write speeds around 70-80MB/s, but when i put truecrypt and ext3 on the top of it write performance becomes very unstable and goes between 1-25MB/s with very high io-wait. on the same server i dont have any performance issues with ext3 on the top of truecrypt on regular 512B-sector 500GB sata disks. so my best guess is that iowaits are caused by misalignment but i cannot really find reliable information on how to calculate optimal partition beginning. i've tried to start it at 128 logical sector, i've also tried 8132 sector as suggested here but both gave me very bad and unstable performance. do you have any experience with similar setup? thanks!

    Read the article

  • Chrome - SSL Security issue on Windows platforms?

    - by al nik
    Fortify.net is a service that displays what's the currently encryption key used by your browser in a https connection. If I browse this site with Chrome 4.1.249.1042 in WinXp SP3 the key used is RC4 cipher, 128-bit key This encryption is weak, and it's the one used by old browsers like IE6. Chrome works fine on Fedora9 and it uses AES cipher, 256-bit key as more modern browsers do (i.e.Firefox) I consider this a security issue. I'm considering to switch back to Firefox in Windows. Do you know if it's possible to change the default encryption key in Chrome?

    Read the article

  • No headphone or speakers plugged in - Windows 7 issue

    - by Amit Ranjan
    I am facing a wierd issue between my sound card driver and Windows7(any edition). I have a sony vaio notebook (VPCEB24EN). Two days ago, on start I got diabled wifi, charging and speakers. Then I restart the PC and everthing worked fine. Later on I again restarted my machine, and then I found the my speakers were not working. I thought, restart will work. I restarted many more times but it did'nt work. I searched google and found that , it might be due to : 1. Hardware is not switched on from bios. 2. No hardware. 3. overriding 64-bit drivers with 32-bit drivers. To make it working, I restored my laptop from scratched, but while restoring pc, the realtek HD drivers, it gave me an error 505. I then formatted the drive and installed Win7 Ultimate 32bit (With PC was, Win7 64-bit Home Basic). I got lots of yellow exclamation in device manager, thinking now this will resolve my issue. But Even after the installing all drivers on a fresh installation, I was still with the same position. A red cross on speaker- No Speakers or Headphone plugged in. Please Note: My Laptop is Vaio , E Series, VPCEB24EN. Audio : Intel® High Definition Audio compatible but accepts Realted Audio. While using BIOS Agent, I got Intel Chipset 5 Series Audio Adapter and ATI RV370 Audio adapter found on my board. Installed is Win7 32bit Ultimate. factory default was Win7 64-bit Home Basic Memory: RAM 3GB/ 320GB HDD Display : ATI Mobility Radeon™ HD 5145 Graphics

    Read the article

  • USPTO site asks for Quicktime Plug-in which I already have installed. Why?

    - by Kensai
    Whenever I try to watch the images of a patent in the USPTO site (example) using Firefox, the browser asks me to download the latest Quicktime, manually. This is totally strange because I already HAVE the latest plug-in (it even appears on my Firefox add-ons list). In the past I have only been able to see patent images using Safari. But never with Firefox. Is it a USPTO problem or a Mozilla one? Is there a way to fix the problem? edit: I can't see TIFF images neither with Internet Explorer (both 32-bit and 64-bit versions) nor with Chrome. All these browsers don't know how to open embedded TIFF images because they don't recognize the installed Quicktime plugin. A USPTO conspiracy to promote Safari? Come to think of it, I had this problem in my old computer as well. It had a 32-bit Vista OS, now I have 64-bit Windows 7. I hate TIFF and can't find Mozilla-specific information anywhere.. Arghh, am I the only one here with this freak problem?!

    Read the article

  • Manually accessing GMail via IMAP

    - by Jeff Mc
    I'm trying to connect to gmail imap, but I am unable to execute any commands after login. I'm running openssl s_client -connect imap.gmail.com:993 to connect then, * OK Gimap ready for requests from 128.146.221.118 42if6514983iwn.40 . CAPABILITY * CAPABILITY IMAP4rev1 UNSELECT IDLE NAMESPACE QUOTA XLIST CHILDREN XYZZY SASL-IR AUTH=XOAUTH . OK Thats all she wrote! 42if6514983iwn.40 . LOGIN {email removed} {password removed} * CAPABILITY IMAP4rev1 UNSELECT LITERAL+ IDLE NAMESPACE QUOTA ID XLIST CHILDREN X-GM-EXT-1 UIDPLUS COMPRESS=DEFLATE . OK {email removed} authenticated (Success) . CAPABILITY at which point it simply hangs with the connection open. I'm guessing gmail pushes you off to a node in a cluster after it authenticate me?

    Read the article

  • Fingerprint of PEM ssh key

    - by Unknown
    I have a PEM file which I add to a running ssh-agent: $ file query.pem query.pem: PEM RSA private key $ ssh-add ./query.pem Identity added: ./query.pem (./query.pem) $ ssh-add -l | grep query 2048 ef:XX:XX:XX:XX:XX:XX:XX:XX:XX:XX:XX:XX:XX:XX:XX ./query.pem (RSA) My question is how I can get the key fingerprint I see in ssh-agent directly from the file. I know ssh-keygen -l -f some_key works for "normal" ssh keys, but not for PEM files. If I try ssh-keygen on the .pem file, I get: $ ssh-keygen -l -f ./query.pem key_read: uudecode PRIVATE KEY----- failed key_read: uudecode PRIVATE KEY----- failed ./query.pem is not a public key file. This key starts with: -----BEGIN RSA PRIVATE KEY----- MIIEp.... etc. as opposed to a "regular" private key, which looks like: -----BEGIN RSA PRIVATE KEY----- Proc-Type: 4,ENCRYPTED DEK-Info: AES-128-CBC,E15F2.... etc.

    Read the article

  • IPTables masquerading with one NIC

    - by Tuinslak
    Hi, I am running an OpenVPN server with only one NIC. This is my current layout: public.ip > Cisco firewall > lan.ip > OpenVPN server lan.ip = 192.168.22.70 The Cisco firewall forwards the requests to the oVPN server, thus so far everything works and clients are able to connect. However, all clients connected should be able to access 3 networks: lan1: 192.168.200.0 (vpn lan) > tun0 lan2: 192.168.110.0 (office lan) > eth1 (gw 192.168.22.1) lan3: 192.168.22.0 (server lan) > eth1 (broadcast network) So tun0 is mapped to eth1. Iptables output: # iptables-save # Generated by iptables-save v1.4.2 on Wed Feb 16 14:14:20 2011 *filter :INPUT ACCEPT [327:26098] :FORWARD DROP [305:31700] :OUTPUT ACCEPT [291:27378] -A INPUT -i lo -j ACCEPT -A INPUT -i tun0 -j ACCEPT -A INPUT -i ! tun0 -p udp -m udp --dport 67 -j REJECT --reject-with icmp-port-unreachable -A INPUT -i ! tun0 -p udp -m udp --dport 53 -j REJECT --reject-with icmp-port-unreachable -A FORWARD -d 192.168.200.0/24 -i tun0 -j DROP -A FORWARD -s 192.168.200.0/24 -i tun0 -j ACCEPT -A FORWARD -d 192.168.200.0/24 -i eth1 -j ACCEPT COMMIT # Completed on Wed Feb 16 14:14:20 2011 # Generated by iptables-save v1.4.2 on Wed Feb 16 14:14:20 2011 *nat :PREROUTING ACCEPT [302:26000] :POSTROUTING ACCEPT [3:377] :OUTPUT ACCEPT [49:3885] -A POSTROUTING -o eth1 -j MASQUERADE COMMIT # Completed on Wed Feb 16 14:14:20 2011 Yet, clients are unable to ping any ip (including 192.168.200.1, which is the oVPN's IP) When the machine was directly connected to the internet, with 2 NICs, it was quite simply solved with masquerading and adding static routes in the oVPN client's config. However, as masquerading won't accept virtual interfaces (eth0:0, etc) I am unable to get masquerading to work again (and I'm not even sure whether I need virtual interfaces). Thanks. Edit: OpenVPN server: # ifconfig eth1 Link encap:Ethernet HWaddr ba:e6:64:ec:57:ac inet addr:192.168.22.70 Bcast:192.168.22.255 Mask:255.255.255.0 inet6 addr: fe80::b8e6:64ff:feec:57ac/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6857 errors:0 dropped:0 overruns:0 frame:0 TX packets:4044 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:584046 (570.3 KiB) TX bytes:473691 (462.5 KiB) Interrupt:14 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:334 errors:0 dropped:0 overruns:0 frame:0 TX packets:334 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:33773 (32.9 KiB) TX bytes:33773 (32.9 KiB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:192.168.200.1 P-t-P:192.168.200.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ifconfig on a client: # ifconfig eth0 Link encap:Ethernet HWaddr 00:22:64:71:11:56 inet addr:192.168.110.94 Bcast:192.168.110.255 Mask:255.255.255.0 inet6 addr: fe80::222:64ff:fe71:1156/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3466 errors:0 dropped:0 overruns:0 frame:0 TX packets:1838 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:997924 (974.5 KiB) TX bytes:332406 (324.6 KiB) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:37847 errors:0 dropped:0 overruns:0 frame:0 TX packets:37847 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2922444 (2.7 MiB) TX bytes:2922444 (2.7 MiB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:192.168.200.30 P-t-P:192.168.200.29 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:689 errors:0 dropped:18 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:468778 (457.7 KiB) wlan0 Link encap:Ethernet HWaddr 00:16:ea:db:ae:86 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:704699 errors:0 dropped:0 overruns:0 frame:0 TX packets:730176 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:520385963 (496.2 MiB) TX bytes:225210422 (214.7 MiB) static routes line at the end of the client's config (I've been playing around with the 192.168.200.0 -- (un)commenting to see if anything changes): route 192.168.200.0 255.255.255.0 route 192.168.110.0 255.255.255.0 route 192.168.22.0 255.255.255.0 route on a vpn client: # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.200.29 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 192.168.22.0 192.168.200.29 255.255.255.0 UG 0 0 0 tun0 192.168.200.0 192.168.200.29 255.255.255.0 UG 0 0 0 tun0 192.168.110.0 192.168.200.29 255.255.255.0 UG 0 0 0 tun0 192.168.110.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 192.168.110.1 0.0.0.0 UG 0 0 0 eth0 edit: Weirdly enough, if I set push "redirect-gateway def1" in the server config, (and thus routes all traffic through VPN, which is not what I want), it seems to work.

    Read the article

  • Strange performance from RAID5 using WD RE4 disks

    - by Howard
    I've noticed a bit of a performance issue with some WD RE4 drives I'm using under AMD's hardware RAID solution. First a bit of background: Environment: Windows 7 home premium x64 HDD's: 3x 1TB WD Raid Edition 4 in a RAID 5 setup with 128 kbyte stripe (2TB usable space) Testing Tool: HD Tune, process set to "High Priority" Processor: AMD Phenom II x6 1100T Ram: 16GB DDR3/1600mhz Motherboard: MSI 970A-G45 The image below pretty much depicts the issue I'm having. Every test has the same thing, a period of similar length where the performance drops to a few megabytes a second. This can't be a TLER issue as the purpose of RE4's is to work around that. Any help would be greatly appreciated.

    Read the article

  • Debian date jumping, causing complete lockup

    - by artfulrobot
    I have a Debian Squeeze VM that has suddenly chosen to jump it's date forwards just over a month, which seems to confuse it no end and cause it to require a hard reset (yikes!). There is nothing unusual in the logs, except that the datestamp suddenly jumps (today back to 2005). It's happened three times, so I don't think it's to do with the leap second issue as the last one of those was in July. When it happened once I spent ages checking stuff but could not find anything, decided to forget it. But three times is becoming an issue on a production server. Edits providing information requested in comments (thanks!): I do not have control over the hypervisor, it is a hired VM. # cat /sys/devices/system/clocksource/clocksource0/current_clocksource kvm-clock # ntpq -p remote refid st t when poll reach delay offset jitter ============================================================================== +grendel.exizten 130.149.17.8 2 u 29 64 77 14.811 1.778 1.744 *panoramix.linoc 193.67.79.202 2 u 32 64 77 19.729 -0.419 1.691 +robert.elnounch 213.251.128.249 2 u 27 64 77 17.762 0.600 1.722 -janetzki.eu 83.169.43.165 3 u 31 64 77 27.214 3.575 1.638

    Read the article

  • SSL Ajax type of certificate for the static domain (image + js)

    - by Alexl
    Hi, I have a page that is SSL and has a valid certificate extended. (mainpage.com) But this page request some static content to another domain(page-static.com), basicly images and js. Actually i have only a certificate for my mainpage.com. So now when i request this page i get invalid ssl page because it contains invalid encrypted data (the one provided by the www.page-static.com) What kind of certificate do i need for the www.page-static.com. Do i need the same one as the mainpage.com, because this certificate are expensive (it's a extended certificate). Or a cheap certificate from godaddy will do the trick. This is another question do both certificates have to be signed by the same root provider and/or the same encryption key length (or it can be only 128 bits)? Thanks for your help

    Read the article

  • What does this diagnostic output mean?

    - by ChrisF
    I recently had a fault with my broadband connection. It turned out to be a fault with the ISP's or teleco's equipment. My ISP posted this diagnostic, but while I understand it in general, I'd like to to know more about the details. I'm assuming that ATM means Asynchronous Transfer Mode and PPP means Point to Point Protocol. It was this that my router was indicating as the fault. xDSL Status Test Summary Sync Status: Circuit In Sync General Information NTE Status: NTE Power Status: Unknown Bypass Status: Upstream DSL Link Information Downstream DSL Link Information Loop Loss: 9.0 17.0 SNR Margin: 25 15 Errored Seconds: 0 0 HEC Errors: 0 Cell Count: 0 0 Speed: 448 8128 TAM Status: Successfully executed operation Network Test: Sub-Test Results Layer Name Value Status Modem pass Transmitter Power (Upstream) 12.4 dBm Transmitter Power (Downstream) 8.8 dBm Upstream psd -38 dBm/Hz Downstream psd -51 dBm/Hz DSL pass Equipment Vendor Name TSTC Equipment Vendor Id n/a Equipment Vendor Revision n/a Training Time 8 s Num Syncs 1 Upstream bit rate 448 kbps Downstream bit rate 8128 kbps Upstream maximum bit rate 1108 kbps Downstream maximum bit rate 11744 kbps Upstream Attenuation 3.5 dB Downstream Attenuation 0.0 dB Upstream Noise Margin 20.0 dB Downstream Noise Margin 19.0 dB Local CRC Errors 0 Remote CRC Errors 0 Up Data Path interleaved Down Data Path interleaved Standard Used G_DMT INP INP Upstream Symbols n/a INP Upstream Delay 4 ms INP Upstream Depth 4 INP Downstream Symbols n/a INP Downstream Delay 5 ms INP Downstream Depth 32 ATM Reason: No ATM cells received fail Number of cells transmitted 30 Number of cells received 0 number of Near end HEC errors 0 number of Far end HEC errors n/a PPP Reason: No response from peer fail PAP authentication nottested CHAP authentication nottested (I'm not sure that Super User is the best place to ask this, but two people have suggested I ask it here so here I am).

    Read the article

  • Problem with Xen, xvda and sda

    - by Javier J. Salmeron Garcia
    I am creating a cloud for my university using Eucalyptus with Xen (PCs have Debian Squeeze 64 bit installed). I have a problem with the following guest configuration: # # Configuration file for the Xen instance evenmorefinalfoo, created # by xen-tools 4.2 on Thu May 26 11:03:06 2011. # # # Kernel + memory size # kernel = '/boot/vmlinuz-2.6.32-5-xen-amd64' ramdisk = '/boot/initrd.img-2.6.32-5-xen-amd64' vcpus = '1' memory = '128' # # Disk device(s). # root = '/dev/sda2 ro' disk = [ 'file:/home/xen/domains/evenmorefinalfoo/disk.img,sda2,w', 'file:/home/xen/domains/evenmorefinalfoo/swap.img,sda1,w', ] As you can see, the disk and swap images are meant to be mounted on sda1 and sda2. However, when I start the guest, these are mounted on xvda1 xvda2, provoking an error. Is there anything that I can do about that? It seems like it is a Xen error. Thank you in advance,

    Read the article

  • What does "cpuid level" mean?

    - by ogzylz
    For an example, I put just output from 1 core of a 16 core machine. What does the output mean by "cpuid level" of "6"? Also, what do "bogomips" of "5992.10" and "clflush size" of "64" mean? processor : 0 vendor_id : GenuineIntel cpu family : 15 model : 6 model name : Intel(R) Xeon(TM) CPU 3.00GHz stepping : 8 cpu MHz : 2992.689 cache size : 4096 KB physical id : 0 siblings : 4 core id : 0 cpu cores : 2 fpu : yes fpu_exception: yes cpuid level : 6 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm syscall nx lm constant_tsc pni monitor ds_cpl vmx cid cx16 xtpr lahf_lm bogomips : 5992.10 clflush size : 64 cache_alignment: 128 address sizes: 40 bits physical, 48 bits virtual power management:

    Read the article

  • What is the meaning of these BIND log messages?

    - by javano
    Please clarify for me the meaning of the following BIND messages in syslog, these are from a DNS resolver. Whilst I think I understand them, I don't know what all four mean, so I think it's best if someone will clarify for me: 1. Oct 14 18:36:34 resolver1 named[14958]: lame server resolving 'arrivatn.co.uk' (in 'arrivatn.co.uk'?): 212.103.224.56#53 2. Oct 14 18:36:36 resolver1 named[14958]: unexpected RCODE (SERVFAIL) resolving '148.128.183.212.in-addr.arpa/PTR/IN': 212.183.136.42#53 4. Oct 14 18:38:49 resolver1 named[14958]: unexpected RCODE (REFUSED) resolving 'internal-server.ournetwork.com/AAAA/IN': auth.dns.server.ip#53 3. Oct 14 18:39:05 resolver1 named[14958]: client 89.187.127.110#42034: query (cache) 'image.sinajs.cn/A/IN' denied Thank you.

    Read the article

  • Bridging LXC containers to host eth0 so they can have a public IP

    - by Vianney Stroebel
    UPDATE: I found the solution there: http://www.linuxfoundation.org/collaborate/workgroups/networking/bridge#No_traffic_gets_trough_.28except_ARP_and_STP.29 # cd /proc/sys/net/bridge # ls bridge-nf-call-arptables bridge-nf-call-iptables bridge-nf-call-ip6tables bridge-nf-filter-vlan-tagged # for f in bridge-nf-*; do echo 0 $f; done But I'd like to have expert opinions on this: is it safe to disable all bridge-nf-*? What are they here for? END OF UPDATE I need to bridge LXC containers to the physical interface (eth0) of my host, reading numerous tutorials, documents and blog posts on the subject. I need the containers to have their own public IP (which I've previously done KVM/libvirt). After two days of searching and trying, I still can't make it work with LXC containers. The host runs a freshly installed Ubuntu Server Quantal (12.10) with only libvirt (which I'm not using here) and lxc installed. I created the containers with : lxc-create -t ubuntu -n mycontainer So they also run Ubuntu 12.10. Content of /var/lib/lxc/mycontainer/config is: lxc.utsname = mycontainer lxc.mount = /var/lib/lxc/test/fstab lxc.rootfs = /var/lib/lxc/test/rootfs lxc.network.type = veth lxc.network.flags = up lxc.network.link = br0 lxc.network.name = eth0 lxc.network.veth.pair = vethmycontainer lxc.network.ipv4 = 179.43.46.233 lxc.network.hwaddr= 02:00:00:86:5b:11 lxc.devttydir = lxc lxc.tty = 4 lxc.pts = 1024 lxc.arch = amd64 lxc.cap.drop = sys_module mac_admin mac_override lxc.pivotdir = lxc_putold # uncomment the next line to run the container unconfined: #lxc.aa_profile = unconfined lxc.cgroup.devices.deny = a # Allow any mknod (but not using the node) lxc.cgroup.devices.allow = c *:* m lxc.cgroup.devices.allow = b *:* m # /dev/null and zero lxc.cgroup.devices.allow = c 1:3 rwm lxc.cgroup.devices.allow = c 1:5 rwm # consoles lxc.cgroup.devices.allow = c 5:1 rwm lxc.cgroup.devices.allow = c 5:0 rwm #lxc.cgroup.devices.allow = c 4:0 rwm #lxc.cgroup.devices.allow = c 4:1 rwm # /dev/{,u}random lxc.cgroup.devices.allow = c 1:9 rwm lxc.cgroup.devices.allow = c 1:8 rwm lxc.cgroup.devices.allow = c 136:* rwm lxc.cgroup.devices.allow = c 5:2 rwm # rtc lxc.cgroup.devices.allow = c 254:0 rwm #fuse lxc.cgroup.devices.allow = c 10:229 rwm #tun lxc.cgroup.devices.allow = c 10:200 rwm #full lxc.cgroup.devices.allow = c 1:7 rwm #hpet lxc.cgroup.devices.allow = c 10:228 rwm #kvm lxc.cgroup.devices.allow = c 10:232 rwm Then I changed my host /etc/network/interfaces to: auto lo iface lo inet loopback auto br0 iface br0 inet static bridge_ports eth0 bridge_fd 0 address 92.281.86.226 netmask 255.255.255.0 network 92.281.86.0 broadcast 92.281.86.255 gateway 92.281.86.254 dns-nameservers 213.186.33.99 dns-search ovh.net When I try command line configuration ("brctl addif", "ifconfig eth0", etc.) my remote host becomes inaccessible and I have to hard reboot it. I changed the content of /var/lib/lxc/mycontainer/rootfs/etc/network/interfaces to: auto lo iface lo inet loopback auto eth0 iface eth0 inet static address 179.43.46.233 netmask 255.255.255.255 broadcast 178.33.40.233 gateway 92.281.86.254 It takes several minutes for mycontainer to start (lxc-start -n mycontainer). I tried replacing gateway 92.281.86.254 by : post-up route add 92.281.86.254 dev eth0 post-up route add default gw 92.281.86.254 post-down route del 92.281.86.254 dev eth0 post-down route del default gw 92.281.86.254 My container then starts instantly. But whatever configuration I set in /var/lib/lxc/mycontainer/rootfs/etc/network/interfaces, I cannot ping from mycontainer to any IP (including the host's) : ubuntu@mycontainer:~$ ping 92.281.86.226 PING 92.281.86.226 (92.281.86.226) 56(84) bytes of data. ^C --- 92.281.86.226 ping statistics --- 6 packets transmitted, 0 received, 100% packet loss, time 5031ms And my host cannot ping the container: root@host:~# ping 179.43.46.233 PING 179.43.46.233 (179.43.46.233) 56(84) bytes of data. ^C --- 179.43.46.233 ping statistics --- 5 packets transmitted, 0 received, 100% packet loss, time 4000ms My container's ifconfig: ubuntu@mycontainer:~$ ifconfig eth0 Link encap:Ethernet HWaddr 02:00:00:86:5b:11 inet addr:179.43.46.233 Bcast:255.255.255.255 Mask:0.0.0.0 inet6 addr: fe80::ff:fe79:5a31/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:64 errors:0 dropped:6 overruns:0 frame:0 TX packets:54 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4070 (4.0 KB) TX bytes:4168 (4.1 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:32 errors:0 dropped:0 overruns:0 frame:0 TX packets:32 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2496 (2.4 KB) TX bytes:2496 (2.4 KB) My host's ifconfig: root@host:~# ifconfig br0 Link encap:Ethernet HWaddr 4c:72:b9:43:65:2b inet addr:92.281.86.226 Bcast:91.121.67.255 Mask:255.255.255.0 inet6 addr: fe80::4e72:b9ff:fe43:652b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1453 errors:0 dropped:18 overruns:0 frame:0 TX packets:1630 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:145125 (145.1 KB) TX bytes:299943 (299.9 KB) eth0 Link encap:Ethernet HWaddr 4c:72:b9:43:65:2b UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3178 errors:0 dropped:0 overruns:0 frame:0 TX packets:1637 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:298263 (298.2 KB) TX bytes:309167 (309.1 KB) Interrupt:20 Memory:fe500000-fe520000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:6 errors:0 dropped:0 overruns:0 frame:0 TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:300 (300.0 B) TX bytes:300 (300.0 B) vethtest Link encap:Ethernet HWaddr fe:0d:7f:3e:70:88 inet6 addr: fe80::fc0d:7fff:fe3e:7088/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:54 errors:0 dropped:0 overruns:0 frame:0 TX packets:67 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4168 (4.1 KB) TX bytes:4250 (4.2 KB) virbr0 Link encap:Ethernet HWaddr de:49:c5:66:cf:84 inet addr:192.168.122.1 Bcast:192.168.122.255 Mask:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) I have disabled lxcbr0 (USE_LXC_BRIDGE="false" in /etc/default/lxc). root@host:~# brctl show bridge name bridge id STP enabled interfaces br0 8000.4c72b943652b no eth0 vethtest I have configured the IP 179.43.46.233 to point to 02:00:00:86:5b:11 in my hosting provider (OVH) config panel. (The IPs in this post are not the real ones.) Thanks for reading this long question! :-) Vianney

    Read the article

  • Config postGreSQL pg_hba.conf restric role access

    - by Mathias
    Hello postgre experts. I am completely new to the game but need the following: I Create a new role with login. Let's say: User1 I then create a Database 'User1Database' and set User1 as the owner. User1 has no rights to do anything except for access. Now when I connect using User1 it somehow has access to all databases. I then learned I neeed to write something in here. User1 should have global access to User1Database and absolutely no access to anything else. What lines do I need to add to my pg_hba file? Currently it looks like this: # IPv4 local connections: host all all 127.0.0.1/32 md5 # IPv6 local connections: host all all ::1/128 md5 host all all 0.0.0.0/0 md5 Hope someone can write me the exact lines and explain them to me.

    Read the article

  • About the External Graphics Card and CPU usage

    - by Balaji
    Hi, We are Rendering 16 live Streams at our client machine through one of our applications and the resolution of the video streams are as 4CIF/MPEG4/25FPS/4000Kbits. The configuration fo the client machine is below. HP Desktop Machine: Microsoft Windows XP Intel (R) Core2 Duo CPU E8400 @ 3.00 GHz 2.99 GHz, 1.94 GB of RAM Intel (R) Q45/Q43 Series Express Chipset (Inbuild) The CPU usage of the machine peaks 99% for 16 straems. After some discussion, we had decided to install external graphics card to reduce the CPU usage. So that, we have tried following graphics cards. NVIDIA Quadro NVS 440 - 128 MB Radeon HD 4350 - 512 MB GDDR2 Redeon HD 4350 - 1GB DDR2 ASUS EAH 4350 Silent 1GB DDR2 But the performance wise no difference, even worst. So, what is the pupuse of these external graphics cards? Really it will reduce the CPU usage? What parameters have to check, if we want to reduce the CPU usage? Please do the needful as soon as possible. Regards Balaji

    Read the article

  • I used "autoconf6" (used to configure IPV6) on an AIX 6 target and I don't know how to change it back.

    - by newtoaix
    So I got curious and ran autoconf6 and now I can't figure out how to undo the changes that were made. I have tried using smitty to modify the en0 interface but have had no luck getting it back to it's old configuration. The old configuration of the aix 6 box was: en0: flags=5e080863,c0 inet 10.10.30.212 netmask 0xffffff00 broadcast 10.10.30.255 tcp_sendspace 131072 tcp_recvspace 65536 lo0: flags=e08084b inet 127.0.0.1 netmask 0xff000000 broadcast 127.255.255.255 inet6 ::1/0 tcp_sendspace 131072 tcp_recvspace 131072 rfc1323 1 then I ran autoconf6 and it was changed to: en0: flags=5e080863,c0 inet 10.10.30.212 netmask 0xffffff00 broadcast 10.10.30.255 inet6 fe80::214:5eff:fe96:b806/64 tcp_sendspace 131072 tcp_recvspace 65536 sit0: flags=8100041 inet6 ::10.10.30.212/96 lo0: flags=e08084b inet 127.0.0.1 netmask 0xff000000 broadcast 127.255.255.255 inet6 ::1/128 tcp_sendspace 131072 tcp_recvspace 131072 rfc1323 1 Any help would be awesome.

    Read the article

  • Choosing A Power Supply [closed]

    - by Geeks On Hugs
    Possible Duplicate: Power Supply Capacity Formula How can I check if my system needs more PSU power? I'm not sure if it's OK or not to ask a hardware question here. If not please let me know a good place but I've always got good info here so I thought I'd give it a shot. I'm custom building a new workstation for coding (Linux/Eclipse). How do I determine how much power the power supply needs? I'm building a mini ITX system on a budget and so I need to get as small as possible that is sufficient. I'll have a mini itx mobo with on board wifi and bluetooth, 8 GB RAM, an Intel i3 3.1 Ghz processor, 64 GB SSD and a slim optical drive. In the future I might add a descrete GPU, 16 GB RAM, 128 GB SSD. What is the minimum power I need and how do I calculate that?

    Read the article

  • Postfix - How to configure to send these emails?

    - by Jon
    I want my mailserver to send mail from my local application "from" any user supplied email address "to" my own address, say "[email protected]". The MX records for "mysite.com" actually point to a different server, even though the outgoing mainserver is running with mydomain set as "mysite.com". Perhaps this is part of the problem? postfix is currently causing a SMTPRecipientsRefused error within the python application. Can anyone point me to what to change in the configuration? Thanks postconf -n: alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases append_dot_mydomain = no biff = no config_directory = /etc/postfix inet_interfaces = all mailbox_command = procmail -a "$EXTENSION" mailbox_size_limit = 0 mydestination = mysite.com, localhost.com, , localhost, * myhostname = mysite.com mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 myorigin = /etc/mailname readme_directory = no recipient_delimiter = + relayhost = smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtpd_banner = $myhostname ESMTP $mail_name (Debian/GNU) smtpd_tls_cert_file = /etc/ssl/certs/ssl-cert-snakeoil.pem smtpd_tls_key_file = /etc/ssl/private/ssl-cert-snakeoil.key smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes

    Read the article

  • iis7 .net webservice 404 error

    - by agilenoob
    I have a webservice /test/Service1.asmx in the same folder as a page /test/test.aspx. The page works fine but I get the message bellow for the services in the same location. I know the file is there and the url is correct, and I have added the script module and managed handler as well. If anyone knows what I'm missing here I'd appreciate it Server Error in '/' Application. The resource cannot be found. Description: HTTP 404. The resource you are looking for (or one of its dependencies) could have been removed, had its name changed, or is temporarily unavailable. Please review the following URL and make sure that it is spelled correctly. Requested URL: /test/Service1.asmx Version Information: Microsoft .NET Framework Version:2.0.50727.4200; ASP.NET Version:2.0.50727.4016 FAILED REQUEST LOG: ModuleName ManagedPipelineHandler Notification 128 HttpStatus 404 HttpReason Not Found HttpSubStatus 0 ErrorCode 0 ConfigExceptionInfo Notification EXECUTE_REQUEST_HANDLER ErrorCode The operation completed successfully. (0x0)

    Read the article

  • if there are multiple kernel module can drive the same device, what is the rule to choose from them?

    - by Dyno Fu
    both pcnet32 and vmxnet can drive the device. $ lspci -k ... 02:01.0 Ethernet controller: Advanced Micro Devices [AMD] 79c970 [PCnet32 LANCE] (rev 10) Subsystem: Advanced Micro Devices [AMD] 79c970 [PCnet32 LANCE] Flags: bus master, medium devsel, latency 64, IRQ 19 I/O ports at 2000 [size=128] [virtual] Expansion ROM at dc400000 [disabled] [size=64K] Kernel driver in use: vmxnet Kernel modules: vmxnet, pcnet32 both kernel modules are loaded, $ lsmod | grep net pcnet32 32644 0 vmxnet 17696 0 mii 5212 1 pcnet32 as you see, kernel driver in use is vmxnet. is there any policy/algorithm in kernel how to choose from the candidates?

    Read the article

< Previous Page | 112 113 114 115 116 117 118 119 120 121 122 123  | Next Page >