Search Results

Search found 12681 results on 508 pages for 'logical drive'.

Page 116/508 | < Previous Page | 112 113 114 115 116 117 118 119 120 121 122 123  | Next Page >

• Can't access shared drive when connecting over VPN

  - by evolvd

  I can ping all network devices but it doesn't seem that DNS is resolving their hostnames. ipconfig/ all is showing that I am pointing to the correct dns server. I can "ping "dnsname"" and it will resolve but it wont resolve any other names. Split tunnel is set up so outside DNS is resolving fine So one issue might be DNS but I have the IP address of the server share so I figure I could just get to it that way. example: \10.0.0.1\ well I can't get to it that way either and I get "the specified network name is no longer available" I can ping it but I can't open the share. Below is the ASA config : ASA Version 8.2(1) ! hostname KG-ASA domain-name example.com names ! interface Vlan1 nameif inside security-level 100 ip address 10.0.0.253 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address dhcp setroute ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! ftp mode passive clock timezone EST -5 clock summer-time EDT recurring dns domain-lookup outside dns server-group DefaultDNS name-server 10.0.0.101 domain-name blah.com access-list OUTSIDE_IN extended permit tcp any host 10.0.0.253 eq 10000 access-list OUTSIDE_IN extended permit tcp any host 10.0.0.253 eq 8333 access-list OUTSIDE_IN extended permit tcp any host 10.0.0.253 eq 902 access-list SPLIT-TUNNEL-VPN standard permit 10.0.0.0 255.0.0.0 access-list NONAT extended permit ip 10.0.0.0 255.255.255.0 10.0.1.0 255.255.255.0 pager lines 24 logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool IPSECVPN-POOL 10.0.1.2-10.0.1.50 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 asdm image disk0:/asdm-621.bin no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list NONAT nat (inside) 1 0.0.0.0 0.0.0.0 static (inside,outside) tcp interface 10000 10.0.0.101 10000 netmask 255.255.255.255 static (inside,outside) tcp interface 8333 10.0.0.101 8333 netmask 255.255.255.255 static (inside,outside) tcp interface 902 10.0.0.101 902 netmask 255.255.255.255 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa authentication enable console LOCAL aaa authentication http console LOCAL aaa authentication serial console LOCAL aaa authentication ssh console LOCAL aaa authentication telnet console LOCAL http server enable http 10.0.0.0 255.255.0.0 inside http 0.0.0.0 0.0.0.0 outside no snmp-server location no snmp-server contact snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set myset esp-aes esp-sha-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map dynmap 1 set transform-set myset crypto dynamic-map dynmap 1 set reverse-route crypto map IPSEC-MAP 65535 ipsec-isakmp dynamic dynmap crypto map IPSEC-MAP interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 crypto isakmp policy 65535 authentication pre-share encryption aes hash sha group 2 lifetime 86400 telnet 0.0.0.0 0.0.0.0 inside telnet timeout 5 ssh 0.0.0.0 0.0.0.0 inside ssh 70.60.228.0 255.255.255.0 outside ssh 74.102.150.0 255.255.254.0 outside ssh 74.122.164.0 255.255.252.0 outside ssh timeout 5 console timeout 0 dhcpd dns 10.0.0.101 dhcpd lease 7200 dhcpd domain blah.com ! dhcpd address 10.0.0.110-10.0.0.170 inside dhcpd enable inside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept ntp server 63.111.165.21 webvpn enable outside svc image disk0:/anyconnect-win-2.4.1012-k9.pkg 1 svc enable group-policy EASYVPN internal group-policy EASYVPN attributes dns-server value 10.0.0.101 vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn split-tunnel-policy tunnelspecified split-tunnel-network-list value SPLIT-TUNNEL-VPN ! tunnel-group client type remote-access tunnel-group client general-attributes address-pool (inside) IPSECVPN-POOL address-pool IPSECVPN-POOL default-group-policy EASYVPN dhcp-server 10.0.0.253 tunnel-group client ipsec-attributes pre-shared-key * tunnel-group CLIENTVPN type ipsec-l2l tunnel-group CLIENTVPN ipsec-attributes pre-shared-key * ! class-map inspection_default match default-inspection-traffic ! ! policy-map global_policy class inspection_default inspect icmp ! service-policy global_policy global prompt hostname context I'm not sure where I should go next with troubleshooting nslookup result: Default Server: blahname.blah.lan Address: 10.0.0.101

  Read the article

• lvm mirroring space unavailable.

  - by Bryan Ward

  I am trying to migrate my data on lvm to two new disks, and setup mirroring between the two. I have successfully migrated all of the data to the first of the two disks, leaving the second one completely available as a mirror. I verified this using pvdisplay -m /dev/sd{g,h}1 --- Physical volume --- PV Name /dev/sdg1 VG Name vg PV Size 931.51 GiB / not usable 3.19 MiB Allocatable yes PE Size 4.00 MiB Total PE 238466 Free PE 82866 Allocated PE 155600 PV UUID v2nc3j-EFBR-QpuG-xgro-Rm59-fmu6-IB3QcR --- Physical Segments --- Physical extent 0 to 49999: Logical volume /dev/vg/videos Logical extents 0 to 49999 Physical extent 50000 to 99999: Logical volume /dev/vg/home Logical extents 0 to 49999 Physical extent 100000 to 129999: Logical volume /dev/vg/music Logical extents 0 to 29999 Physical extent 130000 to 155599: Logical volume /dev/vg/videos Logical extents 50000 to 75599 Physical extent 155600 to 238465: FREE --- Physical volume --- PV Name /dev/sdh1 VG Name vg PV Size 931.51 GiB / not usable 3.19 MiB Allocatable yes PE Size 4.00 MiB Total PE 238466 Free PE 238466 Allocated PE 0 PV UUID LuTrem-WcsZ-qw7l-2CDS-lLKI-wdq0-QEXhLf --- Physical Segments --- Physical extent 0 to 238465: FREE Then when I try to mirror the home logical volume for example, it says that I do not have sufficient space. I used lvconvert -m1 vg/home and the output was: Insufficient suitable allocatable extents for logical volume : 50000 more required Unable to allocate extents for mirror(s). This puzzling to me because it appears as if there is plenty of space on the second disk to mirror. Is there something I have done wrong here? Or is there a way to explicitly tell LVM where to put each leg of the mirror? I'm using lvm2.

  Read the article

• AFP AD ACL permissions issues with external drive

  - by AlanGBaker

  Mac OS X Server 10.4.11 connected to an AD domain system serving AFP shares to Mac OS X 10.5.8. If I create a share on the the internal RAID of the server with an ACL that allows RW to all ("Domain Users"), then it works, but a share created identically on the external RAID appliance (Drobo v2) doesn't. When the share from the Drobo is mounted, it shows no sign that it has any ACLs associated with it: neither in the Finder (Get Info), nor when checked via the terminal with "ls -lae". The Drobo does show that the ACLs exist when I ssh into the server and check it there, but when the clients mount that share, they just... ...disappear. Any thoughts?

  Read the article

• Virtual Hard Drive not booting - VMWare

  - by Chloraphil

  I have a .vmdk (VMWare hard disk) file that I cannot use as the lone disk in a new virtual machine. If I attach it to an existing virtual machine then it works fine. It has Windows Server 2003 on it. When I attempt to boot the new VM it attempts a network boot. EDIT: VMWare Workstation 6.5 I could not find a PXE option in the settings, and I did look in the VM config file for "PXE" but did not find one.

  Read the article

• Windows Server 2008 R2 Finding Hidden files that are causing drive to fill up

  - by Xaxum

  What is the best way to find out what files are sucking up so much space? My Windows directory lists its size as 15 GB but when I run a powershell script against it, it shows 40 GB. It seems 40 GB is about right because if I use that 40 GB and add it to the rest of my folders on C I get the 45 GB that is in use. I checked volume shadow copy and that is disabled and there are no volume shadow files listed. My page file is limited to 3 GB. How can I find out what files are taking 25 GB of space? Final Results: We ended up disabling UAC and then the Properties showed the true file size of the Windows folder, as shown in powershell script. This allowed us to drill down to the folder that had the issues... In our case it was in C:\Windows\System32\config\systemprofile\AppData\Local\VMware\VDM there were several large dump files, these were the mysterious unknown files in WinDirStat. It turns out our nessus scan is crashing a view service for a couple seconds so it creates a large dump file. So we will try this.. https://discussions.nessus.org/thread/5212

  Read the article

• VMWare Workstation can't read CD/DVD drive

  - by Chris W

  A fresh install of VMWare Workstation 7 (7.1.1 build 282343) on Windows 7 64 bit. When I try to read a CD/DVD from a guest (either to install a fresh guest or to read a CD within an existing VM I get the following error: Cannot connect virtual device ide1:0 because no corresponding device is available on the host. I've tried fiddling with the IDE channels as well as tried SCSI with no joy. What am I missing? I can run ISOs fine but I don't want to have to convert everything to an ISO when I presume that this should just work fine.

  Read the article

• 4TB HGST SATA drive only shows 1.62 TB in Windows Server 2012

  - by user136085

  I'm using a Supermicro X9SRE-3F motherboard with the latest BIOS and 2x 4TB drives connected to the on-board SATA controller. If I set the BIOS to RAID and create a RAID 1 array, the array shows up in the BIOS as 3.6TB. However when I boot Windows (on a separate RAID 1 array), the 4TB drives show up individually in disk manager as 2x 1.62TB drives. I could use Windows 2012 to set up software RAID 1, but when I set the BIOS back to 2x individual drives, they still show up in Windows as 2x 1.62TB drives. How do I access the full capacity of these drives? Thanks, Brian Bulaw

  Read the article

• Windows 8, Truecrypt drive mounts but Windows cannot read its content

  - by phil

  I installed Windows 8 and when I started it, it said that it was repairing a disk. The disk was an encrypted Truecrypt disk. I couldn't mount the disk in Truecrypt after that. I tried to repair the header and it worked, now I can mount the disk but neither Windows 7 or 8 can read the content. Windows asks if it should format the disk. I have all the important files on backup, but there are some media files that I would like to get back. Any ideas?

  Read the article

• "Always available offline" option missing on one network drive in Windows 7

  - by Rynardt

  My network setup at home has 2 network storage devices on the network. The one is for media content on a Popcorn Hour A-110 and the other is a D-Link DNS-320 in RAID 1 configuration for business files. When I access these network drives and right click a folder the following context menu appears for the A-110 device, but not for the D-link. I have tested this in both Windows 7 32bit and Windows Vista 64bit. In both instances the "Always available offline" option is only available for the A-110 storage device, and not for the D-link. How do I get this option for the D-link? Any advice or ideas are welcome.

  Read the article

• SQL Server database on an external hard disk drive

  - by Achilles

  Due to some security problems, My boss has asked me to store all sensitive data in external/removable storages like USB stick or external HDD and this specially includes the MDF/NDF/LDF files of SQL Server 2008 we're running. I've been reading for these last three days with no luck to find a solution. Is there any solution at all? Has ever anybody done such thing?

  Read the article

• Disk drive disappear in Windows Explorer driver list

  - by Stan

  OS: WinXP SP3 When pressing win+E or open Windows Explorer, under My Computer, usually there are several disk drives. But somehow they just disappeared. If I type c:\ in address bar, then the disk will re-appear in the tree though. How to get them back to normal? Thanks.

  Read the article

• Moving default web site to another drive

  - by Chadworthington

  I set the default location from c:\inetpub\wwwroot to d:\inetpub\wwwroot but when I access my .NET 4.0 site get this error: Description: An error occurred during the processing of a configuration file required to service this request. Please review the specific error details below and modify your configuration file appropriately. Parser Error Message: Unrecognized attribute 'targetFramework'. Note that attribute names are case-sensitive. Source Error: Line 105: Set explicit="true" to force declaration of all variables. Line 106: --> Line 107: <compilation debug="true" strict="true" explicit="true" targetFramework="4.0"> Line 108: <assemblies> Line 109: <add assembly="System.Web.Extensions.Design, Version=4.0.0.0, Culture=neutral, PublicKeyToken=31BF3856AD364E35"/> When I try to Manage the Basic Settings on the Site and click the "Test Settings" button, I see that I have a problem under "authorization:" The server is configured to use pass-through authentication with a built-in account to access the specified physical path. However, IIS Manager cannot verify whether the built-in account has access. Make sure that the application pool identity has Read access to the physical path. If this server is joined to a domain, and the application pool identity is NetworkService or LocalSystem, verify that <domain>\<computer_name>$ has Read access to the physical path. Then test these settings again. 1) Do I need to grant rights to IIS to the new folder? Which user? I thought it was something like IIS_USER or something similar but I cannot determine the correct name of the user. 2) Also, do I need to set the default version of the framework somewhere at the Default Site level or at the Virtual folder level? How is this done in IIS6, I am used to IIS5 or whatever came with XP Pro. 3) My original site had a subfolder under wwwroot called "aspnet_client." How was this cleated? I manually copied it to the corresponding new location. My app was using seperate ASP specific databases for storing session state and role info, if that is relevant. Thanks

  Read the article

• Dell Inspiron 1525 - internal hard drive not detected

  - by GingerT

  Others have asked about this issue but had intermittent access to their HD, therefore their results did not apply to this situation. I have tried reseating the HD to no effect. I also tried booting from the Internal HD to no effect. Next step get a connector cable and move the data to a different HD, or send in for HD recovery? Any suggestions?

  Read the article

• My network drive disappears from Mac OS Finder

  - by Mariusz

  I have recently bought a Netgear WNDR3800 router to use it in my home network. But just the same day I installed it, I noticed a strange behaviour of Finder and iTunes. Let me explain it further. There is a Synology DS111 NAS attached to that router and two Macs with Mac OS X Lion. One of them is connected by a cable and the second one wirelessly. Before I changed my router to the new one I mentioned above, Finder always used to display my NAS on its sidebar. So I could just click its network name to access shared folders existing on it. But after I installed WNDR3800, I can no longer access the NAS that way. It is no longer displayed. I always have to mount it manually by typing its IP address using the Finder's 'connect to server' option. The same NAS supports TimeMachine backups and has an inbuilt DLNA server. And the same situation here. I can't perform a backup because my NAS is no longer accessible in TimeMachine preferences. iTunes does not display it as well (as a multimedia server) even though it used to before I installed that router. What's important, everything works fine for a couple of minutes after I restart the router or the NAS. Or even when I change the NAS's IP address it becomes accessible again in Finder, TimeMachine and iTunes, but only for some time. Both the Mac computers I mentioned behave the same way. And all those issues have been taking place sice I installed that new router. Before I did that, everything had worked fine. My old router was Netgear WGR614v10. Would you be so kind to tell me what you think could possibly be the reason of that behaviour? What settings of the router should I look closer at? I'm not a network specialist, but is it possible that some network packets are blocked for some reason? I will be grateful for any clues you give me. Thank you.

  Read the article

• Creating a bootable USB drive from a distro split over two DVD ISOs

  - by Kev

  I am searching and not finding the right way to do this. Please note, I don't think I'm trying for anything strange here. I just want to make a bootable USB stick of a single OS that happens to be larger than one DVD and happens to be larger than FAT32 will allow for in a single file. On our slow connection I spent a long time downloading CentOS 5.9's two DVD ISOs: CentOS-5.9-x86_64-bin-DVD-1of2.iso (4.4 GB) CentOS-5.9-x86_64-bin-DVD-2of2.iso (718 MB) I have a USB stick that I want to somehow get these two ISOs on. Since the first one is 4.4 GB, I can't use ISO2USB because it insists on FAT32. I cannot find an alternative that lets you specify more than one ISO image--of the same distro, I'm not trying for some fancy multi-boot thing--to put on the same stick. I guess I should have downloaded the CD ISOs, but I thought I was "saving time" because then I wouldn't have as many files to run through the md5 checker. There's no IMG file of the whole thing (only a net install version, which I don't want--I want to pre-download everything) otherwise I would've gone for that. So, given that I have these two DVD ISOs, how can I get them on a stick that will boot and make use of both of them properly to install CentOS somewhere? Again, I don't think this is anything out of the ordinary, yet I can't find software/docs that seem to support this. Am I stuck re-downloading everything in CD-sized ISOs just to do this? I found this, but it doesn't run on Windows. I am using Windows to prepare the stick.

  Read the article

• Accidentally ejected my Verbatim drive and can't get the icon back

  - by Erin

  Hi, I have time machine running on my iMac OSX v10.5.8 and also have a Verbatim 1TB attached that I use as a workspace/scratchdisk so I can manipulate large music files before I transfer them. However, when cleaning behind my computer the other day I think I dislodged the connection (or maybe one of the kids hit the eject button, i don't know) however, I've re-booted many times and it's not reconnected. It doesn't appear in my disc utility windown and I don't know how to get the icon back! I've looked in time machine but it doesn't appear there at all (cos it's not supposed to I think - it's not connected - my mate hooked it up for me and he won't return my calls!). Help. I don't know how to get it back! Sorry for being a plank.

  Read the article

• VirtualBox: using physical partition as virtual drive

  - by Hamman Samuel

  Background: I am using VirtualBox installed on Windows 7. From within VirtualBox I am using Xubuntu as a virtual OS. The reason I chose this approach is so that I don't have to keep turning off Windows and rebooting from Xubuntu every time I needed to switch OSes. And VirtualBox's seamless mode is pretty amazing to allow me see Xubuntu and Windows 7 all in one screen. Issue: Now I am thinking of a way to have Xubuntu more integrated into my system. By this I mean I want to have a physical partition for Xubuntu. But I want to still have the feeling of the seamless mode. Question: So finally, my question is: is it possible to load a partition in VirtualBox as a virtual OS? Case examples: Ideal scenario would be: I physically boot up and login to Windows 7. Now I want to access Xubuntu, so I load VirtualBox and access my Xubuntu partition without rebooting. And the other way around too, i.e. I boot up the system, login to Xubuntu, and can access the actual Windows 7 partition through VirtualBox. Other info: Please note that I am not talking about getting access to files, as I have a completely separate partition for my files, and am very familiar with VirtualBox's Shared Folders option.

  Read the article

• How SSD hard drive affected speed of your website (asp.net/linq/ms sql database)

  - by Sergey Osypchuk

  I have a small database (<1G) But we have a lot of complex logi? in website and client complains on render time, which is 3-5 seconds. We are not google, and thousands of users a day is our dream, so size is not a problem, but speed is important. Can anybody share with experience with SSD drives for ASP.NET (MVC)/LINQ/MS SQL based application ? How you performance increased? UPDATE: this whitepaper states that it will be 20 times faster. http://www.texmemsys.com/files/f000174.pdf

  Read the article

• Directories shown as files, when sharing a mounted cifs drive

  - by Johan Sigfred Abildskov

  I have an issue where a directory is shown as a file when accessing a samba share ( on Ubuntu 12.10 ) from a Windows machine. The output from ls -ll in the folder on the linuxbox is as follows: chubby@chubby:/media/blackhole/_Arkiv$ ls -ll total 0 drwxrwxrwx 0 jv users 0 Jun 18 2012 _20 drwxrwxrwx 0 jv users 0 Apr 17 2012 _2006 drwxrwxrwx 0 jv users 0 Apr 17 2012 _2007 drwxrwxrwx 0 jv users 0 May 12 2011 _2008 drwxrwxrwx 0 jv users 0 Feb 19 09:53 _2009 drwxrwxrwx 0 jv users 0 Dec 20 2011 _2010 drwxrwxrwx 0 jv users 0 May 8 2012 _2011 drwxrwxrwx 0 jv users 0 Mar 5 11:37 _2012 drwxrwxrwx 0 jv users 0 Feb 28 10:09 _2013 drwxrwxrwx 0 jv users 0 Feb 28 11:18 _Mailarkiv drwxrwxrwx 0 jv users 0 Jan 3 2011 _Praktikanter The entry in /etc/fstab is: # Mounting blackhole //192.168.0.50/kunder/ /media/blackhole cifs uid=jv,gid=users,credentials=/home/chubby/.smbcredentials,iocharset=utf8,file_mode=0777,dir_mode=0777 0 0 When I access the share directly from the NAS on my Windows box, there are no issues. The version of Samba is 3.6.6, but I couldn't find anything in the changelogs that seem relevant. I've tried mounting it in different locations with different permissions, users and groups but I have not made any progress Due to my low reputation on serverfault ( mostly stackoverflow user ) I'm unable to post a screenshot that shows that the directories are shown as files. If I type the full path in explorer, the directory listing works excellently, except for any subdirectories that are then shown as files. Any attack vector for this issue would be greatly appreciated. Please let me know if I have provided insufficient details. Edit: The same share when accessed from a OS X, works perfectly listing the directories as directories. Best Regards!

  Read the article

• Synchronize the same set of files to 2 different locations with 2 different programs for 2 different purposes

  - by Hedgetrimmer

  Because of stupid questionable IT policies at my not-to-be-named place of occupation, I have been (and will be, for the forseeable future) carrying on an external hard drive a unison-synchronized copy of all of my documents and code, including code which resides in some of my "dotfiles" and other code which resides in ~/bin (things I've made are there because ~/bin is in my $PATH) along with some cruft generated (and to be generated) by conscript and its related "giter8" templating system for Scala project boilerplates. Despite this, I do use a symlinking program to store all of my important dotfiles in a subdirectory. Thanks to that somewhat complicated setup, I have resorted to making a directory full of symlinks to every directory (or file, as is the case with stuff under ~/bin) that I want synchronized, and then follow = True is in my unison profile. It happens to be that this collection of odds and ends—plus an automatically-generated text file containing every package installed on my system—is everything under ~ that needs to be backed up to a remote (rsync-over-ssh) host with client-side encryption and signing from GPG. I already believe that duplicity is the most appropriate program to do that. What isn't as clear-cut is how to make duplicity use the exact same set of files when it runs a backup; it would be simple if duplicity would follow symlinks, but it does not and the manpage lists no option for enabling any such behavior. Comparing unison's file selection algorithm to duplicity's, I don't think I can write a program that could compute a ruleset for one program given one for the other. For the record, I would rather not keep the symlinks manually synchronized with duplicity file-selection rules, as they can change thanks to the above-mentioned complications regarding ~/bin. I don't think running duplicity on the external hard disk is such a good idea either; I usually keep that hard disk unmounted and unplugged in case of a power failure or other physical problem with the computer, plus I'm not sure about duplicity's performance given that: the hard disk is NTFS-formatted in order to be useable at my Windows-imprisoned place of occupation. despite being a USB 3.0 disk, my computer has no USB 3.0 ports so it acts as a USB 2.0 disk. How can I have duplicity (or is there a better program that I have overlooked?) back up the exact same set of files that is bidirectionally synchronized with my external hard disk?

  Read the article

• installing on a physical drive with virtualbox/Windows

  - by nos

  How can I install a guest system in virtualbox running on a Windows host ?

  Read the article

• How to prevent HP Photosmart Essential from launching on removal drive insertion

  - by David Boike

  My in-laws bought an HP computer loaded with HP junk, and it's giving me a headache. When they insert a camera memory card into their printer, the Auto-Play dialog comes up, but it also launches the HP Photosmart Essential application, which is a piece of trash. It will NOT launch properly just normally from the taskbar, so that makes it pretty useless. I tried uninstalling it, but then when you insert a memory card, a Microsoft Help window comes up saying how to reinstall HP Photosmart Essential!! Is there any way to find the registry key (I assume) that allows a program to be launched when a memory card is inserted?

  Read the article

• Can't open shared drive after disconnecting vpn

  - by Matt McMinn

  I use a VPN to connect to my office network. On my local network I have another WinXP machine that shares a printer and a few shared folders. While I'm connected to my work VPN, I can access the shared printer and folders on the other machine just fine, and vice versa. Once I disconnect the VPN, I can't access the local machine any more, and the other machine can't access my machine. The network itself seems ok - I can ping the other machine, get to the internet, and get on to a web server shared by the other machine, but I can't get to the shared folders or printer. If I reconnect to the VPN, my access is restored. I'm guessing this is some sort of authentication thing, but I don't know what. Any ideas? Update This problem is bothering me again, so here's an update. Depending on when I first access the WinXP machine, I either have this problem, or the opposite problem. After a reboot, if I (for example) print, then connect to the VPN, I can't access the machine while on the VPN. If after a reboot I connect to the VPN, then print, I can't access the machine off the VPN. In both cases, if I enable/disable the VPN again, I can access the machine again. Thanks

  Read the article

• Phantom Local Disks appearing in my drive list

  - by Paul

  I seem to have several phantom Local Disks mapped to different letters that are of 0 bytes in size. Strangely, they do not show up when I view my drives through Windows Explorer. But if I open an application such as ACDSee Pro or MS Word and then go to open a file I can see all these Local Disks mapped to different letters. This means when I plug in my external hard disk it ends up mapped to letter R instead of its usual G which messes up any programs I have pointing to it by default. How did they get there and more importantly, how do I get rid of them? I'm on a Window 7 Home Premium 32 bit machine.

  Read the article

• Best free tool to find largest files and folders on a drive

  - by oo

  I am looking for a tool to tell me which files and folders are the largest as I need to do some cleanup.

  Read the article

< Previous Page | 112 113 114 115 116 117 118 119 120 121 122 123  | Next Page >