Search Results

Search found 3467 results on 139 pages for 'win'.

Page 116/139 | < Previous Page | 112 113 114 115 116 117 118 119 120 121 122 123  | Next Page >

• How to use SSH Public Key with PuTTY to connect to a Linux machine

  - by ysap

  I am trying to set a public SSH key connection from a Windows 7 machine to a Red-Hat Linux machine. The ultimate purpose is to use pscp (PuTTY's version of scp) from the command terminal w/o the need to type password repetitively. Following PuTTY's documentation and other online sources, I used PuTTYgen to generate a key pair. I then copied the generated public key to a ~/.ssh/authorized_keys file on the Linux machine (as far as I can tell, it runs OpenSSH server). To check the connection, I run PuTTY and set the username and private key file in the appropriate places in its GUI. However, when trying to connect using PuTTY's SSH, the connection uses the preset username, but I get an error message of "Server refused our key" and a prompt for the password. I then tried to copy-paste the public key text from PuTTYgen's GUI to the authorized_keys file, but it did not work either. How should I set up a public key connection form Win 7 to Linux? How do I use this with pscp (rather than PuTTY's ssh)?

  Read the article

• effective back-up using Raid / Win7 back-up

  - by Job

  I have a stand-alone pc system with two 2 tb harddiscs, one of which configured as Raid1, i.e. mirorring. The operational drive is partitioned. I use an external 1 tb harddisc for back-up using Windows 7 back-up facility which will be swapped weekly and stored on other premises. I back-up all partitions AND allow a system back-up. All application software is on the C: partition. Questions: How can I see whether Raid1 is working; i.e. is doing its job. All I see now is a status message in the start-up procedure that says its status is normal. How can I see used or available space on Raid 1? The Win-7 backup allows for 1 schedule only as far as I can see. I want daily back-ups of data. However due to the single schedule I am forced to do the time-consuming system back-up and c: back-up as well. Is there a way to activate two schedules allowing a frequent (daily) data back-up and a system back-up with c: drive back-up on a say weekly basis? Of course it can be forced by hand but I am likely to forget that. I am not the programming type of person so looking for simple and controllable solutions. Thank you - any help is apreciated.

  Read the article

• CC.NET + SVN : Server certificate issue

  - by MSI

  I am trying to setup Continuous Integration in our office. Being a puny little developer I am facing this supposedly infamous problem: " Source control operation failed: svn: OPTIONS of 'https://trunkURL': Server certificate verification failed: issuer is not trusted" So I tried the following solution - Run CC.NET service (server running as win service) using a domain account (rather than default LOCAL SYSTEMS) and accept cert permanently using command prompt under that user by using svn log/list on the repo. Doesn't help :(. I am getting the following from my artifact/log files(or dashboard) ThoughtWorks.CruiseControl.Core.CruiseControlException: Source control operation failed: svn: OPTIONS of 'https://TrunkURL': Server certificate verification failed: issuer is not trusted (https://ServerAdd) . Process command: E:\(svn.exe Path) log https://TrunkURL -r "{2010-11-08T02:12:20Z}:{2010-11-08T02:13:21Z}" --verbose --xml --no-auth-cache --non-interactive at ThoughtWorks.CruiseControl.Core.Sourcecontrol.ProcessSourceControl.Execute(ProcessInfo processInfo) at ThoughtWorks.CruiseControl.Core.Sourcecontrol.Svn.GetModifications(IIntegrationResult from, IIntegrationResult to) at ThoughtWorks.CruiseControl.Core.Sourcecontrol.QuietPeriod.GetModificationsWithLogging(ISourceControl sc, IIntegrationResult from, IIntegrationResult to) at ThoughtWorks.CruiseControl.Core.Sourcecontrol.QuietPeriod.GetModifications(ISourceControl sourceControl, IIntegrationResult lastBuild, IIntegrationResult thisBuild) at ThoughtWorks.CruiseControl.Core.IntegrationRunner.GetModifications(IIntegrationResult from, IIntegrationResult to) at ThoughtWorks.CruiseControl.Core.IntegrationRunner.Integrate(IntegrationRequest request) We are using VisualSVN Server and CC.NET for this adventure. Tips, suggestions will be highly appreciated. Thanks

  Read the article

• Preventing applications from performing run once tasks for multiple users

  - by JohnyV

  In our environment we have several applications that are installed that have a need to run a little prompt the first time they run eg Media player, Google earth etc. The problem is we have many users on many different computers. And the computers have deepfreeze running on them which removes the users profile once the computer is restarted. So next time that user logs in they have to go through the whole thing of run once again. I have managed to prevent IE runonce using group policy and office run once from using the office customisation tool. Is there a way to make this happen for other applications. On windows xp we used to copy a user that has run all the apps and place their default profile into the default profile so that new users get that profile template. Now with windows 7 the process of copy profiles is not as easy. Is there an easy way to copy profiles in win 7 or is there a better way (eg modify reg or app data) to prevent apps from performing an initial run. Thanks

  Read the article

• Live Screencast under Linux

  - by OmnipotentEntity

  I was having some difficulty with running a Live Screencast under Linux. I've found jtvlc and tried using that, but whenever I use it the stream comes out either blank or lagged with extremely high latency. I have a fast internet connection and a fast computer, but am I perhaps taxing it too much? Any ideas on what I could possibly be doing wrong? # 1. Get an account on http://www.justin.tv/ # 2. Copy streaming key from: http://www.justin.tv/broadcast/adv_other # 2. Install VLC: http://www.videolan.org/vlc/ # 3. Get Win/Mac/Lin Stream Client: \ # http://apiwiki.justin.tv/mediawiki/index.php/Linux_Broadcasting_API # 4. Adjust the vlc parameters to your liking and run VLC like this #!/bin/bash cvlc screen:// --input-slave=pulse:// \ --screen-width 1920 \ --screen-height 1080 \ --screen-fps 5 \ -v input_stream \ --sout='#duplicate{ dst="transcode{ scale=1, venc=x264{ keyint=60 }, vcodec=h264, vb=600, acodec=mp4a, ab=32, channels=2, samplerate=22050 } :rtp{dst=127.0.0.1,port=1234,sdp=file:///tmp/vlc.sdp} "}' \ --sout-transcode-threads=4 & sleep 2 # 5. Run JTVLC to stream like this: ./jtvlc/jtvlc omnipotententity censored /tmp/vlc.sdp # Notes: #- If you want to see what you're about to stream add 'dst=display, ' # before 'dst="transcode[' # More about the VLC parameters: http://wiki.videolan.org/Documentation:Modules/screen

  Read the article

• Setting up xpra for client use in OS X

  - by Jonathan

  I've been trying to get xpra to run on OS X for the last few days to connect to my Ubuntu server. Note that there's a GUI for it called shifter, but that (at least on OS X) is still far too buggy. For those who don't know what xpra is, if you know what screen is, it's like screen for GUI X Windows apps tunneled over ssh. You can render a remote X app locally so it's faster than sending a series of compresses screen shots (like VNC), but with xpra you can disconnect and reconnect on different computers. To get the basic functionality you can just type "ssh -X server.location" and any GUI app you open from the command line will open locally. I've been able to get xpra to build by doing the following: Download pari-all-0.0.6.tar.gz from the xpra site listed under upstream and untar it. Issue the following Mac Ports command (Dependencies thanks to RogBlog): sudo port install python25 python26 py26-pyrex py26-gtk xorg-libXtst py25-gobject py25-gtk py25-nose py26-nose xorg-libXdamage xorg-libXcomposite xorg-libXtst xorg-libXfixes In the upstream list of v0.0.06 patches (NOT 0.0.8pre!) on the xpra site listed above, download mswindows-conditional-pyrex.patch. Open the patch with your favorite text editor and change the single occurrence of "win" in it to "darwin". Apply the patch to setup.py. Run do-build in the command line. Now where I'm stumped: how do I run xpra? The build produces a sub directory called install/bin in which xpra is located, but when I try to run it I get the following error: Traceback (most recent call last): File "./xpra", line 4, in import xpra.scripts.main ImportError: No module named xpra.scripts.main There is a file called main.py under xpra/scripts, but I don't know any python and I'm not sure if this is what it's looking for, and what to do with it even if it is. My goal is to set up xpra so I can install it into /usr/bin (or some other common path for executables) and execute it whenever I please. What do I do next?

  Read the article

• How do I restore to a delta file (disk) on Vmware ESXi

  - by Oscar

  Using VMware Server ESXi (freebie version) I have a Virtual Machine (win 2k3 r2 server). When I first provisioned it I took a snapshot of it. I recently tried to clone the primary drive using my standard hardware-based method to grow a windows disk. (using knoppix, clone drive to a new drive, make it bootable, then I intended to extend the partition via diskpart from within windows). This process failed; I tried setting the cloned drive (via the vmware gui) to replace the original drive, boot and be done. This didn't work out so well. The machine never booted. I checked the boot order, the disk location and all the basics I usually do. As a failsafe, I then tried changing all the settings back so the machine would boot to the original drive and I could figure out (as I eventually did) a better way of growing the disk. However when I powered on the machine with the original drive, it reverted back to that initial snapshot I created; It lost all the changes since. I looked in the file system and found a few files, I think the keyfile here is one named "delta" and I'm assuming that's the disk I want, but I can't find a way to have the Virtual Machine actually use that drive/file. It isn't available to add when I go to add an existing drive. Do I need to somehow commit that delta to the original drive and then boot from it again? Can you point me in the right direction? I've since discovered the proper way of growing drives using "vmkfstools" but I need to get back to the original state of the machine to try this out. Any help would be greatly appreciated.

  Read the article

• RHEL 6 vs latest vanilla kernel differences?

  - by Yanko Hernández Álvarez

  What are the differences of the RHEL 6 kernel and the latest kernel.org one? I know RHEL is based on 2.6.32 with some features backported from newer kernels and that it also has other features that are not yet part of the latest vanilla kernel. Is there any comparison of the features of both kernels so I can tell how advanced is the RHEL kernel 6 vs. latest vanilla and vice versa?. It don't have to be the latest kernel at all, but the more recent the vanilla version, the better. What I want to know is: What features I lose/win if I change the RHEL kernel for the latest kernel.org’s one? What features are less matured/developed in the latest vanilla kernel than in RHEL’s (and vice versa)? (I guess KVM virtualization is one of them, but I'm not so sure.) What things (libraries / programs / etc) don’t interact as well with the latest vanilla kernel than with the RHEL’s one? In a related note: Is there ANY way to be as up to date (kernelwise) as possible (using RHEL 6) without loosing too much in the process? (Any way except doing the patching myself, I don’t have the necessary expertise) Any repo I don’t know of? Any alternative? Update: The srpm doesn't include patches (see comments), so that way is not possible. Clarification: I'm interested in how "old" the RHEL kernel gets as time goes by, and to know when the latest upstream kernel includes all the improvements included in the RHEL version.

  Read the article

• Reliable custom Windows shortcut keys?

  - by Peter Baer

  I have global Windows shortcut keys assigned to several different cmd.exe instances. I do this by creating shortcuts to cmd.exe on my desktop, and assigning each one a unique shortcut key (for example, CTRL + SHIFT + U). Pretty basic stuff. I'm using Win2K8 (R1 and R2). This works just fine... most of the time. But with infuriating regularity, sometimes it doesn't. Or it will work with a long delay (many seconds). It doesn't matter what app currently has focus (it can even be one of the command prompts). It doesn't matter what keys I assign (I've tried a few variations of WIN, CTRL and SHIFT). I did notice that this is often, but not always, correlated with explorer.exe struggling in some way or another (say, an explorer window opened to a file share that's unavailable, or an app being unresponsive, or whatever). In other words the shortcut key handling appears to be very sensitive to unrelated system activity. Note that whenever I have this problem I can always successfully ALT + TAB to the window I want to get to, but that's tedious. I use the shortcuts to these command windows hundreds of times a day so even a 1% failure rate becomes really annoying. Is there a way to fix this, or is there some third-party utility out there that will RELIABLY intercept custom key combinations to bring focus to whatever apps I want, in a way that is independent of other system activity? ADDENDUM: There is a property of the Windows shortcuts that I would not want to lose if switching to a third-party hotkey tool: Windows shortcuts are idempotent. Once you've launched a shortcut to some app, pressing the shortcut key combo again takes you to the already launched process - it does not launch a new process.

  Read the article

• Expresscard Not Detected in PCI-E Adapter

  - by maxpower47

  I'm trying to put an expresscard TV tuner (Avermedia HC82) into my HTPC using this expresscard to PCI-E adapter. I've verified that the tuner works fine in my laptop. The motherboard is a Biostar TF7050-M2. When I install it and turn it on, the light on the back of the adapter comes on fine (there are two indicator lights on the back to show if it is using PCI-E or USB communication, USB communication goes through a USB cable connected between the card and a header on the motherboard) showing that it is working in PCI-E mode. However, the device is never detected in Windows 7 Professional x64. The auto detect never happens, it doesn't show up in the device manager, and I can have it rescan for new hardware and nothing is found. I tested the whole setup (tuner + adapter) in another PC (also using Win 7 Pro x64) and it worked fine. I also tried: Plugging the adapter in to the PCI-E x16 slot on the motherboard (I verified first that the x16 slot worked by installing a video card in it) Booting into safe mode and rescanning Updating the chipset drivers Installing the tuner drivers first Using a different USB cable, plugged in to one of the known good ports on the back of the board Trying it without the USB cable plugged in Removing the other PCI cards that were installed on the board Looking through the BIOS for any setting that might be disabling it somehow to no avail. I'm at a loss for what else to try. I really don't want to RMA it (the shipping back to newegg will be almost as much as it cost to buy in the first place. Any ideas?

  Read the article

• Chrome pop-up blocker fail?

  - by Count Zero

  I have this problem since just a few days. I've been a heavy Chrome user for several years, but it never happened before: Sometimes absolutely uncalled for pop-ups appear, when I click something absolutely legit. It seems to happen at a very precise rate of two pop-ups every hour or so. The pop-ups are not very varied, it seems to be a fixed set of some 4-5 ads. At first I thought I caught some malware, but after a full scan with Malwarebytes Anti-Malware, I found absolutely nothing. In addition the problem exists only with Chrome. When I use Firefox, this never ever happens. What is even more puzzling is that it happens on both of my rigs and started on the same day. I have a removable storage that I dock to both of them and access one machine from the other via RDP, but still... It seems this is a problem that others face too. See this Google forum and here. Could it be that the latest Chrome build is just acting up? (Just in case it matters: I run Chrome version 24.0.1312.57 m on Win 7.)

  Read the article

• TCPDump and IPTables DROP by string

  - by Tiffany Walker

  by using tcpdump -nlASX -s 0 -vvv port 80 I get something like: 14:58:55.121160 IP (tos 0x0, ttl 64, id 49764, offset 0, flags [DF], proto TCP (6), length 1480) 206.72.206.58.http > 2.187.196.7.4624: Flags [.], cksum 0x6900 (incorrect -> 0xcd18), seq 1672149449:1672150889, ack 4202197968, win 15340, length 1440 0x0000: 4500 05c8 c264 4000 4006 0f86 ce48 ce3a E....d@[email protected].: 0x0010: 02bb c407 0050 1210 63aa f9c9 fa78 73d0 .....P..c....xs. 0x0020: 5010 3bec 6900 0000 0f29 95cc fac4 2854 P.;.i....)....(T 0x0030: c0e7 3384 e89a 74fa 8d8c a069 f93f fc40 ..3...t....i.?.@ 0x0040: 1561 af61 1cf3 0d9c 3460 aa23 0b54 aac0 .a.a....4`.#.T.. 0x0050: 5090 ced1 b7bf 8857 c476 e1c0 8814 81ed P......W.v...... 0x0060: 9e85 87e8 d693 b637 bd3a 56ef c5fa 77e8 .......7.:V...w. 0x0070: 3035 743a 283e 89c7 ced8 c7c1 cff9 6ca3 05t:(>........l. 0x0080: 5f3f 0162 ebf1 419e c410 7180 7cd0 29e1 _?.b..A...q.|.). 0x0090: fec9 c708 0f01 9b2f a96b 20fe b95a 31cf ......./.k...Z1. 0x00a0: 8166 3612 bac9 4e8d 7087 4974 0063 1270 .f6...N.p.It.c.p What do I pull to use IPTables to block via string. Or is there a better way to block attacks that have something in common? Question is: Can I pick any piece from that IP packet and call it a string? iptables -A INPUT -m string --alog bm --string attack_string -j DROP In other words: In some cases I can ban with TTL=xxx and use that should an attack have the same TTL. Sure it will block some legit packets but if it means keeping the box up it works till the attack goes away but I would like to LEARN how to FIND other common things in a packet to block with IPTables

  Read the article

• How to remove NTFS system files from a previous Vista installation

  - by Boldewyn

  I'm trying to shrink my system partition under Win Vista. It's all fine, except that in front of the last 300MB of the volume sits a single file, that cannot be moved by defrag or other means from its position. It's called C:\$Extend\$UsnJrnl:$J, and my assumtion is, that it is left from a previous installation of Vista, when I re-set up the system. Now, googling for this kind of files brings interesting results, but no solution to my problem: Files left on the disk can become ownerless in a new setup of Windows and inaccessible (even for administrators). To be able to access them again, I found the tip to use takeown to re-assign them to the Admin group (or anyone else). Works like a charm for normal files, but not for the C:\$Extend stuff. The C:\$Extend folder is a system folder of the NTFS file system, where the journal is stored (especially in a file called $UsnJrnl:$Data, whose name is surprisingly close to mine). You can delete the journal with fsutil usn /delete C:, however, this doesn't work from within the booted system (as I found out trying). Also, I'm not quite sure of the side effects. You can't move the NTFS own files with standard defrag tools. The same holds, by the way, for not accessible files. Every bit of knowledge out there is targeted to either not accessible files or the $Extend NTFS stuff, but noone addresses my problem involving both, an inaccessible system file. Question: How can I remove this file, or at least how can I move it on the disk?

  Read the article

• Windows 7: Moving Program Files location during install using unattend.xml

  - by Shevek

  I am planning on using an unattend.xml to create a Windows 7 Ultimate 64-bit setup with Users and ProgramData on a 2nd drive. I have found many samples of how to do this (see below). However I would also like to move Program Files to a 3rd drive as well. i.e.: C:\Windows [SSD] D:\Users [HDD1] D:\ProgramData [HDD1] P:\Program Files [HDD2] P:\Program Files (x86) [HDD2] I have found that this was possible using unattend.txt in XP but all documentation or examples I find about Win 7 only mention Users and ProgramData, not Program Files. Is this possible using an answer file? Sample unattend.xml for Users and ProgramData: <?xml version="1.0" encoding="utf-8"?> <unattend xmlns="urn:schemas-microsoft-com:unattend"> <settings pass="oobeSystem"> <component name="Microsoft-Windows-Shell-Setup" publicKeyToken="31bf3856ad364e35" language="neutral" versionScope="nonSxS" processorArchitecture="amd64"> <FolderLocations> <ProfilesDirectory>D:\Users</ProfilesDirectory> <ProgramData>D:\ProgramData</ProgramData> </FolderLocations> </component> </settings> </unattend>

  Read the article

• Important hardware components to avoid bottlenecks/improve speed on a laptop?

  - by joelhaus

  Looking for a powerful general use (including web development) laptop running Windows. Price points seem to be all over the place. Many less powerful machines are priced much higher than machines with better specs. How does one navigate this market? Are there any unpublished/under-publicized specs/bottlenecks you look for? Understanding that hardware improves over time, is there an efficient ratio that can be used (or something similar, like Windows Experience Index?) which will indicate how powerful a system is? Thanks in advance! P.S. Here is an example from a laptop released on September 17, 2010. Can anyone pick apart these specs? Is there missing information you would be looking for? OS: Win 7 Display: 16.4" LED backlit Processor: Intel Core i7-740QM, 6MB L3 Cache RAM: 6GB DDR3 1333MHz (8GB max.) Graphics: NVIDIA GeForce GT 425M (1 GB of dedicated DDR3) HDD: 500GB 7200RPM SATA Hard Drive Removable Disc: Blue-ray with DVD±R/RW Misc: webcam/mic/speakers/bluetooth (via Sony Vaio VPC-F137FX/B)

  Read the article

• Small office network setups

  - by user39822

  I work at a small office and we're overhauling our network setup there. We're a web dev company and at the moment we have 50+ production sites running on the same machine that runs our internal email, which is just plain stupid. We're moving all our client hosting off site and are now looking for something to run our internal office requirement. Below is a brain dump: Equal amount of Mac & PC, about 25 machines in total. We need a central "server" to host files that should be accessible everyone as a "network drive". If possible we'd like to use low cost hardware for this (Mac or Win based). Disk space should be upward of 1TB. Ideally we should also be able to run a small web server on this machine (LAMP stack) to run some planning and billing applications we wrote ourselves. We need some sort of MS Exchange alternative for things like a shared calendar and especially being able to set Out of Office replies. We have one printer that is connected to the network Setup should be something can preferably be managed easily via a graphical interface and NOT require command line skills. Users want to keep using Apple Mail or MS Outlook After a quick google I came across the Zimbra collaboration suite, can anyone recommend this or any other solution for our office?

  Read the article

• How to verify power provided to processors is clean

  - by GregC

  Once in a blue moon, I am seeing a blue screen of death on a shiny new Dell R7610 with a single 1100 Watt Dell-provided power supply on a beefy UPS. BCode is 101 (A clock interrupt was not received...), which some say is caused by under-volting a CPU. Naturally, I would have to contact Dell support, and their natural reaction would be to replace a motherboard, a power supply, or CPU, or a mixture of the above components. In synthetic benchmarks, system memory and CPU, as well as graphics memory and CPU perform admirably, staying up for hours and days. My questions are: Is power supply good enough for the application? Does it provide clean enough power to VRMs on the motherboard? Are VRMs good enough for dual Xeon E5-2665? Does C-states logic work correctly? Is there sufficient current provided to PCIe peripherals, such as disk controllers? P.S. Recently, I've gone through the ordeal with HP. They were nice and professional about it, but root cause was not established, and the HP machine still is less than 100%, giving me a blue screen of death once in a couple of months. Here's what quick web-searching turns up: http://www.sevenforums.com/bsod-help-support/35427-win-7-clock-interrupt-bsod-101-error.html#post356791 It appears Dell has addressed the above issue by clocking PCIe bus down to 5GT/sec in A03 BIOS. My disk controllers support PCIe 3.0, meaning that I would have to re-validate stability. Early testing shows improvements. Further testing shows significant decrease in performance on each of the x16 slots with Dell R7610 with A03 BIOS. But now it's running stable. HP machine has received a microcode update in September 2013 SUM (July BIOS) that makes it stable.

  Read the article

• RDP Connection to Windows 7 stays really slow

  - by Pavlo

  I have an Issue with connecting to Windows 7 via RDP. I can open an RDP Session, but regardless of any settings, the responce times are really long. This in particulary is the case when opening a web page in a browser. I've tried IE, Firefox and Google Chrome. I also use RDP connection to a Windows 2008 Server from the same client machine, and the speed is very normal with all features turned on. We have Gigabit Ethernet here. So I think it can not be the client's fault. What concerns Windows 7 Machine, I've tried shutting all the sraphic features off and turning the color levels to 256 colors. Result - the same. If I work locally on the machine - I can not see any lags. What else have I tried: Using old RDP 5 Client from Microsoft Setting network autotuninglevel as seen here Do You have some ideas? Thanks in advance! Update the problem seems to be with rendering window contents. All the window borders and pannes are rendered pretty quickly, but the content shows up very slowly. Also mouse movements are recognised by the Win 7 box only after some period. Are there some hidden settings in the RDP, where one could turn some advanced features off or turn some caching on? I use Bitmap Caching, but this apparently doesn't help.

  Read the article

• very slow internet with Linksys WRT54GL only in wireless mode (wired is OK)

  - by gojira

  I bought a new Cisco Linksys WRT54GL router to connect my laptop (running Windows 7) to the internet. I installed Tomato 1.28 firmware on the router. When I connect the laptop to the router via ethernet cable, everything is fine and I get extremely fast up- and download speeds. When I connect wirelesssly however, websites load extremely slow - it takes dozens of seconds to load a website! <-- This is my question, how can I fix the wireless speed issue? Gmail for example is unusable this way. I tried speedtest.net, but this always fails in the upload part of the test so I can't even test the bandwidth (could the fact that it fails in the upload part, not the download part, be an indication what the problem is?!). I have isolated the problem a bit, I am convinced it has to do either with the router itself, the router settings, or the settings of the wireless connection in Win 7. Because previously, I was using another router by Buffalo and I had no problems whatsoever. I have tried to reproduce the settings from the Bufallo router as closely as possible on the Linksys router (same channel, same encryption etc). The download speed problem only occurs with the Linksys router, and only in wireless mode! When I exchange the Linksys router with the Buffalo router I have here for testing, the wireless speed is up to normal again. Also, before I had installed the Tomato firmware I had exactly the same problem, so it has nothing to do with the firmware itself. Notes & things I already tried: Changing the channel: does not seem to affect anything, I am also on the same channel (10) which I was previously on when I had a Buffalo router. QoS is off. Ping to the router itself is OK, ~ 1 ms. Some current settings of the linksys router: WAN / Internet Type: DHCP Wirelesss Mode: Access Point B/G Mode: Mixed Broadcast: check Channel: 10 - 2.457 GHz Security: WPA2 Personal Encryption: AES

  Read the article

• Windows 8.1 in a VMWare Workstation 10 guest's mouse is missing, but only sometimes

  - by Rob Perkins

  I have VMWare Workstation 10 running on a Windows 7 machine, hosting a k guest OS. Before upgrading to WS 10 I was using version 9, and the Win8 guest OS ran without difficulty or error conditions. Since upgrading and installing the most current VMWare Tools inside the guest after upgrading to version 10, there are circumstances where the mouse pointer is not visible; the mouse position appears stuck at a screen location which is not the center of the virtualized display; and mouse click and scrolling events still get processed. Once this begins happening I have to reboot the host machine to get it to stop. (VMWare Tools 9.6.1 build-1378637 is what the WS 10 software installed) The problem seems to correlate with whether the mouse is captured during Win 8.1's bootup process, before control is passed to the login screen. If I explicitly click the mouse into the guest OS and move it slowly around while the system is booting, then I see the mouse after clicking to lift the first screen and expose the password prompt, and there is never a problem within the guest. If I don't do this during bootup, there is no mouse pointer, with the symptoms listed above. I have tried removing and reinstalling VMWare tools, and the other steps published for "mouse problems" from VMWare's chaotic troubleshooting database. The problem persists. Is there a setting in the virtual machine's configuration which could prevent this behavior?

  Read the article

• Windows 7 caches FTP credentials?

  - by Martin Booka Weser

  On my remote maschine i have an iis 7.5 (win server 2008) and set up an ftp site with iis manager authentication. I then did active directory user isolation and isolated my users to physical folders according to their names. So far, so good. I can access with ftp cliens from everywhere with different test accounts that i previously set up in the iis manager auth. Every user connects to its own folder. When i now tested with windows 7 as a client i did the following. Explorer - computer - right click - add network address - the ip of my remote maschine - user1 - password1 Perfect - it works. I now want to connect with user2. So I deleted this network address and set up a new connection, but with user2 (or even anonymous) instead. Now the strange thing: Windows doesn't even ask me for a password again. It just connects me to the folder of the user1. I already disabled ftp caching in the IIS and i disabled the user1 account in IIS manager authentication! Still, if i set up a network connection with this windows 7 it connects to the folder user1 . No matter which username i use (anonymous, administrator, user2,...). And if i connect with other ftp clients or other computers it all works perfectly. So I assume that this one windows somehow caches the credentials... But then, why does the IIS still accepts this credentials even if i disabled this user1 account??? Thanks.

  Read the article

• IIS virtual location path

  - by Worp

  Sorry in advance, for this seems to be a very noobish question and should be easily fixable, yet I can't work it out: I am setting up windows authentication for a website running on IIS 8.5: The Yii framework of the website takes input like http://localhost/mywebsite/index.php/site/loginand processes it, using the "login" action of the "site" Controller. I flipped on URL Rewrite to have nicer URLs, leaving the URL with /mywebsite/site/login. Now I need to set up windows authentication for this location. Very specifically ONLY for this very exact location. Only the /site/login location of mywebsite needs to have authentication. Every other location needs to have anonymous. Since it is a "virtual location", I don't know how to do it. I can set up win-auth for files, directories, virtual directories, etc. but not for virtual locations that do not map to any file but only to a Controller/Action in Yii. The working counterpart in Apache is but i can't "translate this into IIS". I have read that IIS does have the "~" symbol but I just couldn't make it work yet. Could it be used to achieve authentication on a location basis? I have looked around virtual directories as well, which seem to simply be a kind of "symlink" to actual folders on the harddrive. Can they be used differently to "create a virtual folder in a location that doesn't really exist to manage its properties"? Help is much appreciated.

  Read the article

• Can MySQL use multiple data directories on different physical storage devices

  - by sirlark

  I am running MySQL with its data dir on a 128Gb SSD. I am dealing with large datasets (~20Gb) that are loaded and processed weekly, each stored in a separate DB for the purposes of time point comparisons. Putting all the data into a single database in unfeasible because the performance on such large databases is already a problem. However, I cannot keep more than 6 datasets on the SSD at a time. Right now I am manually dumping the oldest to much larger 2Tb spinning disk every week, and dropping the database to make space for the new one. But if I need one of the 'archived' databases (a semi regular occurrence) I have to drop a current one (after dumping), reload it, do what I need to, then reverse the results. Is there a way to configure MySQL to use multiple data directories, say one on the SSD and one on the 2Tb spinning disk, and 'merge' them transparently? If I could do this, then archiving would no longer mean "moved out of the database entirely", but instead would mean "moved onto the slow physical device". The time taken to do my queries on a spinning disk would be less than that taken to completely dump, drop, load, drop, reload two entire databases, so this is a win. I thought of using something like unionfs but I can't think of a way to control which database gets stored on which physical drive, because it works by merging on a directory level (from what I understand) so I'm still stuck with using multiple directories. Any help appreciated, thanks in advance

  Read the article

• My bios datetime is resetting to 2002, what should I do?

  - by Thierry Lam

  I bought my PC brand new in mid-2006. I'm currently dual booting Win XP 32 bits and Ubuntu Karmic Desktop. Over the last few days, when I boot up my computer, it tells me that my bios time is not set. I now have 2 choices for booting in: Windows first: I can safely get into Windows but the date now shows 2002/01/01 at 00:00. From there, Windows will not sync its time to its servers, I have to manually advance the date myself. I can also advance the date from the bios at startup. Ubuntu first: Since the time date is still set at 2002, the boot system cannot find my linux partition. I can fix that issue by booting to Windows, set the date properly and the linux issue will be fixed automatically. The above two issues can also be fixed if I manually set the bios date/time manually when I turn on my computer. It's annoying to do that every single day since I shut down my PC daily. Am I having an OS issue or a hardware issue? How can I resolve this problem?

  Read the article

• How do I keep a table in Sync across 4 db's to be used in SQL Replication Filtering?

  - by Refracted Paladin

  I have a Win Form, Data Entry, application that uses 4 seperate Data Bases. This is an occasionally connected app that uses Merge Replication (SQL 2005) to stay in Sync. This is working just fine. The next hurdle I am trying to tackle is adding Filters to my Publications. Right now we are replicating 70mbs, compressed, to each of our 150 subscribers when, truthfully, they only need a tiny fraction of that. Using Filters I am able to accomplish this(see code below) but I had to make a mapping table in order to do so. This mapping table consists of 3 columns. A PrimaryID(Guid), WorkerName(varchar), and ClientID(int). The problem is I need this table present in all FOUR Databases in order to use it for the filter since, to my knowledge, views or cross-db query's are not allowed in a Filter Statement. What are my options? Seems like I would set it up to be maintained in 1 Database and then use Triggers to keep it updated in the other 3 Databases. In order to be a part of the Filter I have to include that table in the Replication Set so how do I flag it appropriately. Is there a better way, altogether? SELECT <published_columns> FROM [dbo].[tblPlan] WHERE [ClientID] IN (select ClientID from [dbo].[tblWorkerOwnership] where WorkerID = SUSER_SNAME()) Which allows you to chain together Filters, this next one is below the first one so it only pulls from the first's Filtered Set. SELECT <published_columns> FROM [dbo].[tblPlan] INNER JOIN [dbo].[tblHealthAssessmentReview] ON [tblPlan].[PlanID] = [tblHealthAssessmentReview].[PlanID] P.S. - I know how illogical the DB structure sounds. I didn't make it. I inherited it and was then told to make it a "disconnected app."

  Read the article

< Previous Page | 112 113 114 115 116 117 118 119 120 121 122 123  | Next Page >