Search Results

Search found 3489 results on 140 pages for 'tcp'.

Page 118/140 | < Previous Page | 114 115 116 117 118 119 120 121 122 123 124 125  | Next Page >

• Slow Local Network, Windows 7, Snow Leopard, WiFi/Wired

  - by WerkkreW

  I am experiencing really poor local network performance in my home. I was recently using a Linksys WRT54G Router with DD-WRT on it, and a couple comparable Linksys-G PCI cards for connectivity but decided to upgrade hoping it would help with my performance issues. The computers in my house are connected as follows: Comcast Business Class Commercial 25mbps/10mbps (Verified) D-Link DGL-4500 Wireless N Router Windows 7x64 - D-Link DWA-552 Wireless-N Windows 7x64 - D-Link DWA-552 Wireless-N Mac Mini 10.6.2 - AirPort Extreme N Playstation 3, Hard Wired Xbox 360, Hard Wired Essentially the problem is very specific. Web browsing and uploading/downloading files from the internet is fine, more than fine. But if I want to say, Stream a video from one of my Windows 7 computers to my PS3, or copy a large video file between either of the PC's or the Mac, I get a consistent 500-900Kbps throughput at the high end. If I open my network browser, or try to browse my homegroup the response time is horrible. Both of my Windows computers are showing Strong wireless signals with a connection speed of 300Mbps. I know I can never expect to achieve anything near those speeds, but 500Kbps? Here is what I have tried so far: Enabled Single mode N-only and N/G Only on router WPA2 with AES Encrpytion Disabled "Remote Differential Compression" in Windows 7 Disabled TCP "Auto-Tuning" Used other software for file copies such as "Teracopy" I am at the end of my rope. Unfortunately I live in a 75 year old home with plaster walls, so hard-wiring my entire house isn't really an option I can handle right now. Any ideas to help me get decent speed when transferring files across my network would be greatly appreciated.

  Read the article

• Internet Explorer not working after establishing a SSTP VPN connection

  - by Massimo

  I have a problem which is constantly appearing on each Windows 7 computer I'm using, whenever I establish a SSTP VPN connection to a ForeFront TMG 2010 firewall; it only happens with SSTP connections, not PPTP/L2TP ones. The problem appears only if using a proxy server for Internet access; it doesn't happen when directly accessing the Internet (with or without NAT). It doesn't seem to depend on a specific proxy software being used (I've seen it happening with various ones). The problem is: as soon as I start the VPN connection, Internet Explorer can't access anything anymore. I'm not using the VPN connection as a default gateway, and I can succesfully ping the proxy server after the VPN connection is esatablished (and even telnet to its 8080 TCP port), so this is definitely not a routing problem. Also, the problem is specifically related to Internet Explorer: while it seems not able to connect to any site, other programs (such as FireFox) have no problem accessing the Internet through the same proxy. This behaviour can be easily reproduced on any Windows 7 computer (the service pack and patch level doesn't seem to matter at all). Have IE connect through a proxy, establish a SSTP VPN connection... and IE will just not work anymore until the VPN connection is dropped.

  Read the article

• Printer spooler service stop running when sent print job

  - by Hanan N.

  Every time i am sending a print job to the printer, i am don't get any response from the printer, and at the printer job list at the status of the job, i see that there was an Error, but it don't give me any clue on what could be the problem. After some investigation i found that every time that i send the print job to the printer the printer spooler service stops to run, then after a second or two it start again (i think that this behavior is related to the printer spooler settings to rerun it self after it stops). Things that i have tried so far: Remove and Install again the Driver. After removing the driver, i have removed the unnecessary registry keys according to this article from Microsoft, these are: Rename all files and folders in: c:\windows\system32\spool\drivers\w32x86 Remove anything but Drivers Print and Processors: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Print\Environment\Windows NT x86 Remove anything in here: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Print\Monitors but: BJ Language Monitor Local Port Microsoft Document Imaging Writer Monitor Microsoft Shared Fax Monitor Standard TCP/IP Port USB Monitor WSD Port Disconnect and Reconnect the Printer. Clean the computer from Viruses & Spywares. Currently i am stuck, i have no more things to try, if anybody know about any kind of solution please let me know about it. Since i am want to keep this post as general problem that relate to the printer spooler, and not just my particular problem, i didn't included inside the windows version & the printer model, they are (although i think that it isn't relate just for that particular model): Windows 7 32bit, HP Officejet 4500 G510g-m (connect to the computer via USB). Thanks.

  Read the article

• CentOS 6.3 Virtual under OpenVZ cannot ping, host lookups, outbound connections while postfix running

  - by Paul Cravey

  My best theory is that some kernel limit is being hit preventing outbound connections. We have tried basically everything from tcpdumps to provisioning an entirely new virtual server (we do not have this problem on any other virtuals), however the problem somehow carried over, even with new postfix build (working). Emails work, and outbound connections work, so long as postfix does not have too much going on. /proc/user_beancounters shows no limits being hit (show below). Nevertheless, pings fail even to IP addresses. TCP stack appears healthy. Load is low. No iowait. Flushed iptables already. Has anyone experienced anything like this? uid resource held maxheld barrier limit failcnt 3: kmemsize 166216365 170262528 9223372036854775807 9223372036854775807 0 lockedpages 0 0 9223372036854775807 9223372036854775807 0 privvmpages 285727 351885 9223372036854775807 9223372036854775807 0 shmpages 16933 17605 9223372036854775807 9223372036854775807 0 dummy 0 0 0 0 0 numproc 150 303 9223372036854775807 9223372036854775807 0 physpages 314156 326191 0 1280000 0 vmguarpages 0 0 9223372036854775807 9223372036854775807 0 oomguarpages 165355 165355 9223372036854775807 9223372036854775807 0 numtcpsock 89 172 9223372036854775807 9223372036854775807 0 numflock 22 76 9223372036854775807 9223372036854775807 0 numpty 1 2 9223372036854775807 9223372036854775807 0 numsiginfo 0 75 9223372036854775807 9223372036854775807 0 tcpsndbuf 2733472 4371752 9223372036854775807 9223372036854775807 0 tcprcvbuf 1798336 5427296 9223372036854775807 9223372036854775807 0 othersockbuf 491120 1000760 9223372036854775807 9223372036854775807 0 dgramrcvbuf 0 238728 9223372036854775807 9223372036854775807 0 numothersock 361 505 9223372036854775807 9223372036854775807 0 dcachesize 135941831 136114679 9223372036854775807 9223372036854775807 0 numfile 2905 4990 9223372036854775807 9223372036854775807 0 dummy 0 0 0 0 0 dummy 0 0 0 0 0 dummy 0 0 0 0 0 numiptent 8 9 9223372036854775807 9223372036854775807 0 [root@bni /]# ping 4.2.2.1 PING 4.2.2.1 (4.2.2.1) 56(84) bytes of data. --- 4.2.2.1 ping statistics --- 9 packets transmitted, 0 received, 100% packet loss, time 8493ms [root@bni /]# service postfix stop [root@bni /]# ping 4.2.2.1 PING 4.2.2.1 (4.2.2.1) 56(84) bytes of data. 64 bytes from 4.2.2.1: icmp_seq=1 ttl=53 time=8.63 ms 64 bytes from 4.2.2.1: icmp_seq=2 ttl=53 time=8.62 ms 64 bytes from 4.2.2.1: icmp_seq=3 ttl=53 time=8.63 ms 64 bytes from 4.2.2.1: icmp_seq=4 ttl=53 time=8.66 ms Outbound connections of all sorts fail when postfix is running.

  Read the article

• SSH tunnel for socks5 proxy is slow with concurrent load

  - by RawwrBag

  I ssh to a remote AWS server using Ubuntu. I use ssh's port forwarding capabilities to do this. I have tried forwarding a dynamic port (ssh -D) or a single port (ssh -L with dante running as a remote socks server). Both are equally slow. I also tried different ciphers (ssh -c). Concurrent TCP connections pretty much do not work. For example, I can go to speedtest.net and start a test (which is fairly fast, probably maxes out my line speed) and if I try and do anything (i.e. load google.com) while the test is still running, all the additional connections seem to hang until the speed test is over. I realize OpenSSH is single-threaded. Is this the problem? It doesn't even show up on my top. Same goes for sshd on the remote server -- no processor hit. Is there anyway to bump ssh performance or should I step up to OpenVPN or something better suited for this?

  Read the article

• IIS not responding with SSL Server Hello

  - by Damien_The_Unbeliever

  I'm having difficulty getting a particular IIS machine to "do" SSL. This is a test environment (one of many) which we've set up "the same" as we have many times previously, but it just doesn't seem to be working. The server is Windows Server 2003 (Version 5.2 (Build 3790.srv03_sp2_gdr.100216-1301 : Service Pack 2)) IIS is hosting 4 sites (including the default site), but only one site is configured for SSL. We're using the same SSL certificate we use on all of our other servers (it's a wildcard cert). (Don't think this is relevant, but including anyway) We've configured the site to require SSL, it has a subdirectory that doesn't require SSL but has an asp page that redirects into SSL. The 403;4 error page for the site is hooked up to this asp page (this is how we do our non-HTTPS into HTTPS transition). Using Microsoft Network Monitor (3.3), I've just run a session against a server where SSL is working. It can pull apart the SSL exchange as the following messages: SSL: Client Hello SSL: Server Hello. Certificate. Server Hello Done SSL: Client Key Exchange. Change Cipher Spec. Encrypted Handshake Message. SSL: Change Cipher Spec. Encrypted Handshake Message However, on our problem server, I only see: SSL: Client Hello. The next packet from the server (from port 443, so it's listening and responding there) contains only 60 bytes, and just seems to have the Tcp headers and not much else (but I'm by no means an expert at deciphering these things). So, where do I look next? Or what additional information do I need to add to this question, and where do I find it?

  Read the article

• How to configure a large mtu (linux)

  - by Somejan

  I have a gigabit ethernet connection from my laptop to my router, and a working ipv6 connection to the internet. I can receive very large packets from sites on the internet, with sizes up to at least 10000 bytes (according to wireshark). (edit: turns out to be linux's 'generic receive offload') However, when trying to send anything, my local computer fragments at just below 1500 bytes for ipv6. (On ipv4, I can send tcp packets to the internet of at least 1514 bytes, I can ping with packets up to the configured mtu of 6128 but they are blackholed.) I'm on ubuntu 12.04. I have configured an mtu for my eth0 of 6128 (the maximum it accepts), both using ip link set dev eth0 mtu 6128 and in the NetworkManager applet gui, and restarted the connection. ip link show eth0 shows the 6128 mtu is indeed set. ip -6 route shows that none of the paths the kernel knows about have an mtu set. I can ping over ipv4 with packets up to 6128 bytes (though I don't get responses), but when I do ping6 myrouter -c3 -s1500 -Mdo I get error replies from my own computer saying that the packets are too large and the mtu is 1480. I have confirmed with Wireshark that nothing is put on the wire, and the replies are indeed generated by my own computer. So, how do I get my computer to use the larger mtu?

  Read the article

• Nginx/puma rhel unix socket permission error?

  - by Kevin Brown

  When I try to start my puma server, I get the error: /.rvm/gems/ruby-2.1.1/gems/puma-2.9.0/lib/puma/binder.rb:275:in `initialize': Permission denied - connect(2) for "/var/run/nvhbase.sock" (Errno::EACCES) My sites-available/nvhbase.conf file: upstream nvhbase { server unix:/var/run/nvhbase.sock; } server { listen 80 default_server; server_name 207.131.132.219; root /home/vf032500/dev/nvh/public; location / { proxy_pass http://unix:/var/run/nvhbase.sock; proxy_http_version 1.1; proxy_set_header Upgrade $http_upgrade; proxy_set_header Connection $connection_upgrade; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-Proto https; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_redirect off; } } I don't know a lot about unix sockets and everything works fine using tcp/puma default. My rails app is in my user directory. Is that the problem?? socket is starting in /var/run--I can start in /tmp, but I've heard that's bad practice? Provided I start the server in /tmp, I then can't access it via the server's ip--then what? I'm happy to provide any needed info, I just don't know a whole lot about server/nginx/puma.

  Read the article

• Configuring a MySQL 5.1 Instance on Windows 7 Professional x64 Fails

  - by Thomas Owens

  I'm trying to set up my laptops to function as mobile development environments. Installing the software on my Linux machine and getting it configured was fairly straightforward, however I'm having trouble getting MySQL 5.1 Server installed and configured on Windows 7 Professional 64-bit. I'm currently using the Windows MSI Installer for the complete MySQL 5.1 system (as opposed to the Essentials installer also available). I've tried to install using both the 32-bit and 64-bit versions of MySQL 5.1 - the same events occur in both. I've installed both the Server Instance Configuration Wizard and Workbench and everything appears to be installed just fine. When I open the Instance Configuration Wizard, I select Detailed Configuration. On the next screen, I select Development Environment, then Multifunctional Database on the next screen. I leave the InnoDB settings unchanged. I select Manual Setting with 5 concurrent connections. I enable TCP/IP Networking on Port 3306 and Enable Strict Mode. I select the Standard Character Set. I check the boxes for Install as a Windows Service (and provide the name "MySQL") and Include the Bin Directory in Windows PATH. On the next screen, I set my root user name and password. I do not enable root access from remote machines and I also do not create an anonymous account. On the final screen of the wizard, when I click "Execute", the first two tasks (Prepare Configuration and Write Configuration File) complete. However, when it reaches Start Service, the wizard hangs and becomes unresponsive ("Not Responding" appears in the title bar and Task Manager). I would really like to be able to use both my Windows and Linux laptops as full-blown mobile development environments, but I can't do that without being able to run MySQL. Has anyone encountered this problem before? What options do I have to correct it?

  Read the article

• IP tables blocking access to most hosts but some accesses being logged

  - by epo

  What am I getting wrong? A while back I locked down my web hosting service while hardening it or at least trying to. Apache listens on port 80 only and I set up iptables using the following: IPS="list of IPs" iptables --new-chain webtest # Accept all established connections iptables -A INPUT --protocol tcp --dport 80 --jump webtest iptables -A INPUT --match state --state ESTABLISHED,RELATED --jump ACCEPT iptables -A webtest --match state --state ESTABLISHED,RELATED --jump ACCEPT for ip in $IPS; do iptables -A webtest --match state --state NEW --source $ip --jump ACCEPT done iptables -A webtest --jump DROP However looking at my apache logs I notice various log entries in access_log, e.g. 221.192.199.35 - - [16/May/2010:13:04:31 +0100] "GET http://www.wantsfly.com/prx2.php?hash=926DE27C156B40E55E4CFC8F005053E2D81E6D688AF0 HTTP/1.0" 404 206 "-" "Mozilla/ 4.0 (compatible; MSIE 6.0; Windows NT 5.0)" 201.228.144.124 - - [16/May/2010:11:54:16 +0100] "GET /w00tw00t.at.ISC.SANS.DFind:) HTTP/1.1" 400 226 "-" "-" 207.46.195.224 - - [16/May/2010:04:06:48 +0100] "GET /robots.txt HTTP/1.1" 200 311 "-" "msnbot/2.0b (+http://search.msn.com/msnbot.htm)" How are these slipping through? I don't mind the indexing bots (though I am a little surprised to see them get through). I suppose they must be getting through using the ESTABLISHED,RELATED rules. And no, I can't for the life of me remember why the first match state rule is there So 2 questions: is there a better way to set up iptables to restrict access to specified hosts? How exactly are these 3 examples slipping through?

  Read the article

• How can I avoid my web browser from redirecting to localhost using WAMP in Windows7?

  - by Josh

  I'm currently using Windows 7 with WAMP to try and work on some software, but my web browsers will not accept cookies from the "localhost" domain. I tried creating a few bogus domains in my hosts file by pointing them to 127.0.0.1 but when I type them in I am automatically redirected back to localhost. I have also configured virtualhosts in apache to correspond with the domains I added to the hosts file and it still redirects back to localhost. Is there anything special I must do on Windows 7 to get around this localhost redirect? Thanks for looking :) I'll include my host file here: # Copyright (c) 1993-2009 Microsoft Corp. # # This is a sample HOSTS file used by Microsoft TCP/IP for Windows. # # This file contains the mappings of IP addresses to host names. Each # entry should be kept on an individual line. The IP address should # be placed in the first column followed by the corresponding host name. # The IP address and the host name should be separated by at least one # space. # # Additionally, comments (such as these) may be inserted on individual # lines or following the machine name denoted by a '#' symbol. # # For example: # # 102.54.94.97 rhino.acme.com # source server # 38.25.63.10 x.acme.com # x client host # localhost name resolution is handled within DNS itself. # 127.0.0.1 localhost # ::1 localhost 127.0.0.1 magento.localhost.com www.localhost.com Thanks for looking :)

  Read the article

• Windows 7 remote desktop encryption error every few minutes

  - by rfrankel

  Because of an error in data encryption, this session will now end. This is the error I've been getting more and more frequently over the past few days, to the point that I can't ignore it because it's happening consistently within 5 minutes of connecting - sometimes within a few seconds. Both the remote and local machines are Windows 7 Pro x64. The remote machine is behind a Linksys RV082, and I'm using UPnP to forward a remote port to the correct local port. This setup had been working fine for several months, and I can't think of any recent relevant changes that might have been made. Things I've already tried: Disabling unnecessary components of the network connection on the remote machine, until only IPv4 and Client for Microsoft Networks remain. Disabling TCP large send offload on both the remote and local machines. Confirming that the remote machine is not mentioned anywhere in any DMZ settings on the Linksys router. Confirming that there are no x509-related registry keys screwing things up (this is the suggested fix for a slightly different error anyway). These are the only solutions I've been able to find after about an hour of searching, and most of them apply to XP or Server 2003 in any case. If anyone could suggest something else, it would be much appreciated.

  Read the article

• Set up Linux box as WAP for MyBookLive?

  - by AcidFlask

  I inherited an old Linux box as well as a MyBookLive and would like to make the MyBookLive available over my wireless, essentially using the Linux box as a wireless access point. I just wiped the Linux box (home) and installed Ubuntu 12.04 on it. My network setup currently looks like this: (192.168.0.1 netmask 255.255.255.0) ISP --- wireless router --- wlan0 on home (192.168.0.12) | eth0 on home --- MyBookLive MacBook (192.168.0.11) so that the MyBookLive is basically a glorified external hard drive. The router does have an Ethernet port, but it is being used by my roommate's computer so I can't plug the MyBookLive directly into it. Right now I can ping MyBookLive.local and MacBook.local from home, but I am having trouble understanding and figuring out what the correct iptables commands are to make my MacBook see my MyBookLive through the Bonjour network. Also, I'm not sure if I need to set up DNS to forward xxx.local Bonjour/Zeroconf addresses. I tried the following to forward my entire wired network (which has only my MyBookLive) to a single IP address: sysctl net.ipv4.ip_forward=1 iptables -A FORWARD -i wlan0 -o eth0 -j ACCEPT iptables -A FORWARD -i eth0 -o wlan0 -j ACCEPT iptables -t nat -A PREROUTING -i eth0 -p tcp -j DNAT --to 192.168.0.66 iptables -t nat -A PREROUTING -i eth0 -p udp -j DNAT --to 192.168.0.66 but I can't ping this address from my MacBook. This is probably horribly wrong, but I am a complete noob at setting up this kind of network and could use some expert help with setting this up properly.

  Read the article

• MRTG Monitoring of Disk

  - by Antitribu

  I am trying to monitor Disk usage over SNMP using MRTG on CentOS5.2. I'm open to any suggestions as to the best way to achieve this (I would also like to do other metrics like CPU). Please don't assume I know anything about MRTG. I am using the following config: LoadMIBs: /usr/share/snmp/mibs/UCD-SNMP-MIB.txt,/usr/share/snmp/mibs/TCP-MIB.txt workdir: /var/www/html/mrtg/temp/ # # Disk Usage Monitoring # Target[servername.]: dskPercent.0&dskPercent.0:[email protected] Title[servername.]: / on servername routers.cgi*Desc[servername.]: / on servername routers.cgi*ShortDesc[servername.]: / MaxBytes[servername.]: 100 AbsMax[servername.]: 100 Options[servername.]: growright,nopercent,gauge YLegend[servername.]: used disk space ShortLegend[servername.]: % used Legend1[servername.]: usage Legend2[servername.]: usage Legend3[servername.]: peak usage Legend4[servername.]: peak usage LegendI[servername.]: usage LegendO[servername.]: usage routers.cgi*Icon[servername.]: disk-sm.gif routers.cgi*Options[servername.]: noo,nomax,noabsmax Unscaled[servername.]: dwmy I receive the errors: Unknown SNMP var dskPercent.0 at /usr/bin/mrtg line 2035 Unknown SNMP var dskPercent.0 at /usr/bin/mrtg line 2035 From forum surfing etc the suggestion is to use the fully qualified OIDs, I'd like to avoid this (for readability). So essentially I'm wondering where can I find a mib file compatible with mrtg for it's reference or a working config file.

  Read the article

• Lighttpd + django on gentoo 10 seconds to answer

  - by plaetzchen

  I want to run a Django site on a lighttpd with fastcgi on a gentoo machine. Everytime I try to access the site I get a response after more or less exactly 10 seconds. Im using a socket to let lighttpd communicate with my Django site, but a tcp port doesn't help either. Could this be a lighttpd problem? I tried to both from a server in the internet as well as from localost, this is what lighttpd gives me in the error.log 2012-07-10 14:36:36: (response.c.300) -- splitting Request-URI 2012-07-10 14:36:36: (response.c.301) Request-URI : / 2012-07-10 14:36:36: (response.c.302) URI-scheme : http 2012-07-10 14:36:36: (response.c.303) URI-authority: owntube 2012-07-10 14:36:36: (response.c.304) URI-path : / 2012-07-10 14:36:36: (response.c.305) URI-query : 2012-07-10 14:36:36: (response.c.300) -- splitting Request-URI 2012-07-10 14:36:36: (response.c.301) Request-URI : /owntube.fcgi/ 2012-07-10 14:36:36: (response.c.302) URI-scheme : http 2012-07-10 14:36:36: (response.c.303) URI-authority: owntube 2012-07-10 14:36:36: (response.c.304) URI-path : /owntube.fcgi/ 2012-07-10 14:36:36: (response.c.305) URI-query : 2012-07-10 14:36:36: (response.c.349) -- sanatising URI 2012-07-10 14:36:36: (response.c.350) URI-path : /owntube.fcgi/ 2012-07-10 14:36:36: (mod_access.c.135) -- mod_access_uri_handler called 2012-07-10 14:36:36: (mod_fastcgi.c.3632) handling it in mod_fastcgi 2012-07-10 14:36:36: (response.c.470) -- before doc_root 2012-07-10 14:36:36: (response.c.471) Doc-Root : /var/www/owntube 2012-07-10 14:36:36: (response.c.472) Rel-Path : /owntube.fcgi 2012-07-10 14:36:36: (response.c.473) Path : 2012-07-10 14:36:36: (response.c.521) -- after doc_root 2012-07-10 14:36:36: (response.c.522) Doc-Root : /var/www/owntube 2012-07-10 14:36:36: (response.c.523) Rel-Path : /owntube.fcgi 2012-07-10 14:36:36: (response.c.524) Path : /var/www/owntube/owntube.fcgi 2012-07-10 14:36:36: (response.c.541) -- logical -> physical 2012-07-10 14:36:36: (response.c.542) Doc-Root : /var/www/owntube 2012-07-10 14:36:36: (response.c.543) Rel-Path : /owntube.fcgi 2012-07-10 14:36:36: (response.c.544) Path : /var/www/owntube/owntube.fcgi

  Read the article

• IPTABLE & IP-routed netwok solution for HOST net and VM's subnet

  - by Daniel

  I've got ProxmoxVE2.1 ruled KVM node on Debian and bunch of VM's guests machine. That is how my networking looks like: # network interface settings auto lo iface lo inet loopback # device: eth0 auto eth0 iface eth0 inet static address 175.219.59.209 gateway 175.219.59.193 netmask 255.255.255.224 post-up echo 1 > /proc/sys/net/ipv4/conf/eth0/proxy_arp And I've got two working subnet solution auto vmbr0 iface vmbr0 inet static address 10.10.0.1 netmask 255.255.0.0 bridge_ports none bridge_stp off bridge_fd 0 post-up ip route add 10.10.0.1/24 dev vmbr0 This way I can reach internet, to resolve outside hosts, update and download everything I need but can't reach one guest VM out of any other VM's inside my network. The second solution allows me to communicate between VM's: auto vmbr1 iface vmbr1 inet static address 10.10.0.1 netmask 255.255.255.0 bridge_ports none bridge_stp off bridge_fd 0 post-up echo 1 > /proc/sys/net/ipv4/ip_forward post-up iptables -t nat -A POSTROUTING -s '10.10.0.0/24' -o vmbr1 -j MASQUERADE post-down iptables -t nat -D POSTROUTING -s '10.10.0.0/24' -o vmbr1 -j MASQUERADE I can even NAT internal addresses: -t nat -I PREROUTING -p tcp --dport 789 -j DNAT --to-destination 10.10.0.220:345 My inexperienced mind is ready to double VM's net adapters: one for the first solution and another - for second (with slightly different adresses) but I'm pretty sure that it's a dumb way to resolve the problem and everything can be resolved via iptables/ip route rules that I can't create. I've tried a dozen of "wizard manuals" and "howto's" to mix both solution but without success. Looking for an advice (and good reading links for networking begginers).

  Read the article

• Slow browsing through IE on Windows Server 2012

  - by Volodymyr

  We've run into strange issue on the freshly installed servers. H/W: IBM server X3550 M4 7914; OS: Windows Server 2012 Std. Then we try to browse on the servers thru IE, not all sites are opened or it takes too long time to open the page, i.e. very few of them can be opened. Local FW are disabled. Servers are in a new subnet and traffic is allowed for it. VLAN is configured properly Another Windows Server 2012 host is running OK and Internet access works fine, but it is VM running on Hyper-V 2012. No proxy is used on the network. At the same time, if one tries to establish telnet session to any site on 80/443 ports - it does work. Google works as well. I've tried to configure single Qlogic adapter to check if the issue remains - it does. Teaming is configured with the means of QLogic, not by built-in functionality. IE Enhanced Security is disabled. IE settings were reset, more than once. Why would certain sites work while others not - Idk. I also tried to disable ecncapability and restart server - no luck netsh int tcp set global ecncapability=disabled Any thoughts? UPD1 VMQ is disabled. Servers are not running Hyper-V. UPD2 Servers were rebuilt from scratch, got a mail a few mins ago. Issue still remains. Teaming is now configured with the means of Windows Server 2012.

  Read the article

• Linux port-based routing using iptables/ip route

  - by user42055

  I have the following setup: 192.168.0.4 192.168.0.6 192.168.0.1 +-----------+ +---------+ +----------+ |WORKSTATION|------| LINUX |------| GATEWAY | +-----------+ +---------+ +----------+ 192.168.150.10 | 192.168.150.9 +---------+ | VPN | +---------+ 192.168.150.1 WORKSTATION has a default route of 192.168.0.6 LINUX has a default route of 192.168.0.1 I am trying to use the gateway as the default route, but route port 80 traffic via the VPN. Based on what I read at http://www.linuxhorizon.ro/iproute2.html I have tried this: echo "1 VPN" >> /etc/iproute2/rt_tables sysctl net.ipv4.conf.eth0.rp_filter = 0 sysctl net.ipv4.conf.tun0.rp_filter = 0 sysctl net.ipv4.conf.all.rp_filter = 0 iptables -A PREROUTING -t mangle -i eth0 -p tcp --dport 80 -j MARK --set-mark 0x1 ip route add default via 192.168.150.9 dev tun0 table VPN ip rule add from all fwmark 0x1 table VPN When I run "tcpdump -i eth0 port 80" on LINUX, and open a webpage on WORKSTATION, I don't see the traffic go through LINUX at all. When I run a ping from WORKSTATION, I get this back from some packets: 92 bytes from 192.168.0.6: Redirect Host(New addr: 192.168.0.1) Vr HL TOS Len ID Flg off TTL Pro cks Src Dst 4 5 00 0054 de91 0 0000 3f 01 4ed3 192.168.0.4 139.134.2.18 Is this why my routing is not working ? Do I need to put GATEWAY and LINUX on different subnets to prevent WORKSTATION being redirected to GATEWAY ? Do I need to use NAT at all, or can I do this with routing alone (which is what I want) ?

  Read the article

• Port knocking via SSH tunnels

  - by j0ker

  I have a server running in my university's internal network. There is only one SSH daemon running which is secured by port knocking with knockd. Works fine if I try to connect from within the internal network. But since the server has no external IP, I have to tunnel into the internal network every time I want to access the server from outside. And since tunneling only works for a single port I cannot do the port knocking as easily as from an internal client. In fact, I don't get it to work at all. What I'm trying is opening tunnels for all the different ports that have to be knocked. Then I send TCP-SYN packets into the tunnels. But that doesn't work even for a single port. If I establish the tunnel on the first port in the knock sequence and send a packet through it, it doesn't reach the server. There is no entry in the log file of knockd, while there should be something like 123.45.67.89: openSSH: Stage 1 (as shown with internal knocks). So I guess, the problem doesn't exist within my knocking script but is a more general one. Are there any known problems with what I'm trying to do? Is it even possible or am I missing something? Thanks in advance!

  Read the article

• NAT and P2P router crash

  - by returnFromException

  So..i had this argument with my networks teacher. He said that some people complains about router crashes due to many entrys on NAT tables on a router. I didnt understand and i asked: "If the application uses the same port, why does the router crash?. It should have only one entry (pc-ip,pcport;public-ip,public-port)". And he said: "it doesnt matter its using the same port". I got the idea that NAT creates an entry for every packet that passes trought it. Iam assuming NAT with overloading as you might have guessed. So the questions are: 1-How does nat entrys are created? On a packet basis or connection basis? I mean: suppose i send a udp packet..does the router create an entry? 2-When i start a TCP connection, does the router create a persistant nat entry until the connection closes? 3-Was my teacher right? The NAT table can overload assuming an aplication on the same port sending packets? Thanks in advance.

  Read the article

• Troubleshoot IIS 6 and Intermittent SQL Server Connectivity Loss

  - by jpsnow

  I am not a System Administrator, but I am temporarily trying to fill that role. I have 2 Windows 2003 Servers. 1 server has my Microsoft SQL Database (SQL Server 2005) and the other is the web server with IIS6. Intermittently (once every month or 2) the web server loses connectivity to the database server for a period of roughly 10 minutes. It normally regains connectivity without intervention. The website is set up to send me an email when there is a problem connecting to the database. Within the email, I get the error code: [Microsoft][ODBC SQL Server Driver][TCP/IP Sockets]SQL Server does not exist or access denied. I am able to access both servers during the outage. I can go to my SQL server and open up SQL server without any issues. I have looked in the EventViewer and do not see anything. The last time that I had this issue, I stopped IIS6 and started it. After doing this, the issue was resolved. This leads me to believe that it is an issue with IIS and not SQL server. How can I begin troubleshooting?

  Read the article

• Encrypting peer-to-peer application with iptables and stunnel

  - by Jonathan Oliver

  I'm running legacy applications in which I do not have access to the source code. These components talk to each other using plaintext on a particular port. I would like to be able to secure the communications between the two or more nodes using something like stunnel to facilitate peer-to-peer communication rather than using a more traditional (and centralized) VPN package like OpenVPN, etc. Ideally, the traffic flow would go like this: app@hostA:1234 tries to open a TCP connection to app@hostB:1234. iptables captures and redirects the traffic on port 1234 to stunnel running on hostA at port 5678. stunnel@hostA negotiates and establishes a connection with stunnel@hostB:4567. stunnel@hostB forwards any decrypted traffic to app@hostB:1234. In essence, I'm trying to set this up to where any outbound traffic (generated on the local machine) to port N forwards through stunnel to port N+1, and the receiving side receives on port N+1, decrypts, and forwards to the local application at port N. I'm not particularly concerned about losing the hostA origin IP address/machine identity when stunnel@hostB forwards to app@hostB because the communications payload contains identifying information. The other trick in this is that normally with stunnel you have a client/server architecture. But this application is much more P2P because nodes can come and go dynamically and hard-coding some kind of "connection = hostN:port" in the stunnel configuration won't work.

  Read the article

• Poor write performance on Debian server running NFS with 22TB exported JFS filesystem

  - by user143546

  I am currently running a debian server that is exporting a large JFS filesystem (22TB) over NFS (nfs-kernel-server.) When attempting to write to the NFS share, the performance is very poor. The 22TB disk is sitting on a NAS mounted using iSCSI. It will bust for a moment near expected line speed, and then sit idle for several seconds. Very little traffic measured in the low kb/sec. The wait peeks on write. When reading from the NFS mount, the system operates at expected speeds (11MB/sec). The issue does not occur when using SFTP, rsync, or local coping (non-nfs). The issue persists between stable and testing releases. On the same machine I have a 14TB ext4 filesystem using the exact same export configuration that does not share the issue. This share is not in regular use and thus not consuming resources. NFS Server: cat /etc/exports /data2 10.1.20.86(rw,no_subtree_check,async,all_squash) cat /sys/block/sdb/queue/scheduler noop [deadline] cfq cat /etc/default/nfs-kernel-server RPCNFSDCOUNT=8 RPCNFSDPRIORITY=0 RPCMOUNTDOPTS=--manage-gids NEED_SVCGSSD= RPCSVCGSSDOPTS= NFS Client: cat /etc/fstab 10.1.20.100:/data2 /root/incoming nfs rw,noatime,soft,intr,noacl 0 2 cat /sys/block/sdb/queue/scheduler noop [deadline] cfq cat /proc/mounts 10.1.20.100:/data2/ /root/incoming nfs4 rw,noatime,vers=4,rsize=262144,wsize=262144,namlen=255,soft,proto=tcp,port=0,timeo=600,retrans=2,sec=sys,clientaddr=10.1.20.86,minorversion=0,addr=10.1.20.100 0 0 This problem has me pretty stumped. Any help would be greatly welcomed. Thanks.

  Read the article

• then an error occurred during the login process - Connection Error 233

  - by scott brunner

  We have SQL Server 2008 installed on 64Bit Windows Server 2003. When we try connect to the local SQL Server using SQL Server Management Studio at the console, we get the error: A connection was successfully established with the server, but then an error occurred during the login process. provider: Shared Memory Provider, error: 0 - No process is on the other end of the pipe. When we try TCP from same local SSMS to local server, we get the same error but intead of the pipe message its something like "connection forcibly closed". Now, here is the strange part - we CAN connect to this SQL Server from any other machine on the network using SSMS. - AND - WE CAN'T connect to ANY SQL Server from the problem server. So it seems the SQL Server instance is fine and accepting remote connections. However, the SSMS on that machine will not connect to any SQL Server even remotely. When we try an ADO.NET connection from C# remotely we can connect, run that same code on the console of the trouble server and we get the same errors. How can this be solved?

  Read the article

• Trouble connecting to a local SQL server instance from the web

  - by dfarney

  We have a small network behind a firewall (WatchGuard XTM 2 series) and network switch. On our network we have multiple instances of SQL server, but 1 in specific that I would like to be able to access remotely from our website. We have a static IP address from our ISP and then all the machines on the network have a locally assigned dynamic IP address. When trying to connect to the database from outside our network how do I get the request to be directed to the proper machine / SQL instance? Is it a parameter in my connection string or something in my firewall? A few things to rule out: 1) The firewall is allowing access from the website to our network. I added the site's IP and opened up port 1433. Also, when trying to connect and monitoring the firewall no exceptions come up as they did before I added the proper IP address. 2) Remote connections on the SQL server has been setup and enabled. I've done a lot of reading up on remote connections and I am sure it has been setup properly. I am currently getting this error message on my site: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: TCP Provider, error: 0 - A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host has failed to respond.)

  Read the article

< Previous Page | 114 115 116 117 118 119 120 121 122 123 124 125  | Next Page >