Search Results

Search found 4721 results on 189 pages for 'traffic'.

Page 118/189 | < Previous Page | 114 115 116 117 118 119 120 121 122 123 124 125  | Next Page >

• Q8300 Core-2 Quad vs X3360 Xeon

  - by alchemical

  I'm looking at this ABMX server, and trying to decide on the CPU. I'm purchasing 2 servers, to be used as dedicated web and DB servers for a web site that has low traffic now but could ramp up quickly. Just trying to decide if it is worth about $200 more (per server) for the Xeon vs the core-2. Passmark rates them at 3567 and 4153, which didn't seem that different. I'm not planning at this point to need virtualization. I did hear rumors that Xeon stands up better in a 24/7 server environment, but heard others say there wasn't that much difference. Planning to run Windows Server 2008, likely the R2 release, with 8GB RAM.

  Read the article

• VPN only connects to its server!

  - by Eddie

  Hi guys; Previously I bought a windows 2003 VPS and enabled routing and remote access so that users can make a vpn connection. I turend the firewall off and everything was working fine. But since 2 days ago whenever I try and connect to vpn it connects to vpn without any problem and I can see the connection status however it only connects to the server I mean what I can do with this vpn is to connect to the server via remote desktop and I can ping only the server's IP, neither I can open any webpages in browsers or ping other IP addresses beside the server one! I've also rebuilt the server and configured it for routing access and vpn connection from the beginning but it doesn't work either. It seems that server fails to route the traffic properly, as i'm sure that the firewall has been turned off I can't figure out what's the reason, any idea what's going on? Thanks in advance

  Read the article

• Apache2 mod_proxy and post-multipart size

  - by Pietro

  Hi, I have Apache2 configured to proxy all traffic directed to a specific virtual host to a local tomcat instance. All is good and fine but for multipart posts larger than ~100kb. Such posts fail on the tomcat end with an exception like SocketTimeoutException. If I connect directly to Tomcat (which listens on a port != 80) then all posts are handled just fine. The Apache virtual host config goes like this: NameVirtualHost * SetOutputFilter DEFLATE <VirtualHost *> ServerName foo.bar.com ErrorLog c:/wamp/logs/foo_error.log CustomLog c:/wamp/logs/foo_access.log combined ProxyTimeout 60 ProxyPass / http://localhost:10080/foo/ ProxyPassReverse / http://localhost:10080/foo/ ProxyPassReverseCookieDomain localhost bar.com ProxyPassReverseCookiePath /foo / </VirtualHost> I tried browsing the Apache2 and mod_proxy docs but found nothing useful. Any idea why Apache2 refuses to proxy requests bigger than X bytes ? Thanks!

  Read the article

• Connecting to VPN via Proxy

  - by Rodrigo

  Hi, My company's VPN server is located in Netherlands, from my current location this is a really crappy place in terms of connectivity, connection keeps dropping, it's slow and keeps being reset during high traffic times. I have a dedicated server over USA which is able to connect to VPN server without this issues, connection is stable and fast. My question is, how do I connect to this VPN using a proxy running on my dedicated server? I'm on Windows 7 using a VM on XP to connect to the VPN. Thanks.

  Read the article

• pfsense multi-site VPN VOIP deployment

  - by sysconfig

  have main office pfsense firewall configured like this: local networks WAN - internet LAN - local network VOIP - IP phones need to connect remote offices (multi-users) and single remote users (from home) use IPSEC or OpenVPN to build "permanent" automatically connecting tunnels from remote location to main location. in remote locations, network will look like this: WAN - internet LAN - local network multiple users VOIP - multiple IP phones in order for the IP phones to work they have to be able to "see" the VOIP network and the VOIP server back at the main office for single remote users ( like from home ) the setup will be similar but only one phone and one computer so questions: best way to tie networks together? IPSEC or OpenVPN can this be setup to automatically connect ? any issues/suggestions with that design/topology ? QoS or issues with running the VOIP traffic over a VPN throughput, quality etc.. obviously depends on remote locations connection to some degree

  Read the article

• Bonjour/mDNS Broadcast across subnets

  - by Matthew Savage

  I have just setup a new OSX Server in our office and verified that everything is working fine over our wired network (192.168.126.0/24). The problem that I am having is that our clients (Mac Laptops) are mainly connected via Wireless, which are running on a different subnet (192.168.1.0/24), and the mDNS Broadcast isn't reaching this subnet. The network configuration is somewhat foreign to myself (I don't manage the network in this location, but as of just recently the servers), however I don't believe there is any firewalls or routing rules between the two subnets which might cause the traffic to be rejected. I'm wondering if this is simply the mDNS broadcast not able to broadcast over the two different subnets (I'm still reading up on broadcast to understand it more) or there is something else which I might be able to try.

  Read the article

• OpenVPN on ec2 bridged mode connects but no Ping, DNS or forwarding

  - by michael

  I am trying to use OpenVPN to access the internet over a secure connection. I have openVPN configured and running on Amazon EC2 in bridge mode with client certs. I can successfully connect from the client, but I cannot get access to the internet or ping anything from the client I checked the following and everything seems to shows a successful connection between the vpn client/server and UDP traffic on 1194 [server] sudo tcpdump -i eth0 udp port 1194 (shows UDP traffic after establishing connection) [server] sudo iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere ACCEPT all -- anywhere anywhere Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere anywhere Chain OUTPUT (policy ACCEPT) target prot opt source destination [server] sudo iptables -L -t nat Chain PREROUTING (policy ACCEPT) target prot opt source destination Chain POSTROUTING (policy ACCEPT) target prot opt source destination MASQUERADE all -- ip-W-X-Y-0.us-west-1.compute.internal/24 anywhere Chain OUTPUT (policy ACCEPT) target prot opt source destination [server] openvpn.log Wed Oct 19 03:11:26 2011 localhost/a.b.c.d:61905 [localhost] Inactivity timeout (--ping-restart), restarting Wed Oct 19 03:11:26 2011 localhost/a.b.c.d:61905 SIGUSR1[soft,ping-restart] received, client-instance restarting Wed Oct 19 03:41:31 2011 MULTI: multi_create_instance called Wed Oct 19 03:41:31 2011 a.b.c.d:57889 Re-using SSL/TLS context Wed Oct 19 03:41:31 2011 a.b.c.d:57889 LZO compression initialized Wed Oct 19 03:41:31 2011 a.b.c.d:57889 Control Channel MTU parms [ L:1574 D:166 EF:66 EB:0 ET:0 EL:0 ] Wed Oct 19 03:41:31 2011 a.b.c.d:57889 Data Channel MTU parms [ L:1574 D:1450 EF:42 EB:135 ET:32 EL:0 AF:3/1 ] Wed Oct 19 03:41:31 2011 a.b.c.d:57889 Local Options hash (VER=V4): '360696c5' Wed Oct 19 03:41:31 2011 a.b.c.d:57889 Expected Remote Options hash (VER=V4): '13a273ba' Wed Oct 19 03:41:31 2011 a.b.c.d:57889 TLS: Initial packet from [AF_INET]a.b.c.d:57889, sid=dd886604 ab6ebb38 Wed Oct 19 03:41:35 2011 a.b.c.d:57889 VERIFY OK: depth=1, /C=US/ST=CA/L=SanFrancisco/O=EXAMPLE/CN=EXAMPLE_CA/[email protected] Wed Oct 19 03:41:35 2011 a.b.c.d:57889 VERIFY OK: depth=0, /C=US/ST=CA/L=SanFrancisco/O=EXAMPLE/CN=localhost/[email protected] Wed Oct 19 03:41:37 2011 a.b.c.d:57889 Data Channel Encrypt: Cipher 'BF-CBC' initialized with 128 bit key Wed Oct 19 03:41:37 2011 a.b.c.d:57889 Data Channel Encrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Wed Oct 19 03:41:37 2011 a.b.c.d:57889 Data Channel Decrypt: Cipher 'BF-CBC' initialized with 128 bit key Wed Oct 19 03:41:37 2011 a.b.c.d:57889 Data Channel Decrypt: Using 160 bit message hash 'SHA1' for HMAC authentication Wed Oct 19 03:41:37 2011 a.b.c.d:57889 Control Channel: TLSv1, cipher TLSv1/SSLv3 DHE-RSA-AES256-SHA, 1024 bit RSA Wed Oct 19 03:41:37 2011 a.b.c.d:57889 [localhost] Peer Connection Initiated with [AF_INET]a.b.c.d:57889 Wed Oct 19 03:41:39 2011 localhost/a.b.c.d:57889 PUSH: Received control message: 'PUSH_REQUEST' Wed Oct 19 03:41:39 2011 localhost/a.b.c.d:57889 SENT CONTROL [localhost]: 'PUSH_REPLY,redirect-gateway def1 bypass-dhcp,route-gateway W.X.Y.Z,ping 10,ping-restart 120,ifconfig W.X.Y.Z 255.255.255.0' (status=1) Wed Oct 19 03:41:40 2011 localhost/a.b.c.d:57889 MULTI: Learn: (IPV6) -> localhost/a.b.c.d:57889 [client] tracert google.com Tracing route to google.com [74.125.71.104] over a maximum of 30 hops: 1 347 ms 349 ms 348 ms PC [w.X.Y.Z] 2 * * * Request timed out. I can also successfully ping the server IP address from the client, and ping google.com from an SSH shell on the server. What am I doing wrong? Here is my config (Note: W.X.Y.Z == amazon EC2 private ipaddress) bridge config on br0 ifconfig eth0 0.0.0.0 promisc up brctl addbr br0 brctl addif br0 eth0 ifconfig br0 W.X.Y.X netmask 255.255.255.0 broadcast W.X.Y.255 up route add default gw W.X.Y.1 br0 /etc/openvpn/server.conf (from https://help.ubuntu.com/10.04/serverguide/C/openvpn.html) local W.X.Y.Z dev tap0 up "/etc/openvpn/up.sh br0" down "/etc/openvpn/down.sh br0" ;server W.X.Y.0 255.255.255.0 server-bridge W.X.Y.Z 255.255.255.0 W.X.Y.105 W.X.Y.200 ;push "route W.X.Y.0 255.255.255.0" push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 208.67.222.222" push "dhcp-option DNS 208.67.220.220" tls-auth ta.key 0 # This file is secret user nobody group nogroup log-append openvpn.log iptables config sudo iptables -A INPUT -i tap0 -j ACCEPT sudo iptables -A INPUT -i br0 -j ACCEPT sudo iptables -A FORWARD -i br0 -j ACCEPT sudo iptables -t nat -A POSTROUTING -s W.X.Y.0/24 -o eth0 -j MASQUERADE echo 1 > /proc/sys/net/ipv4/ip_forward Routing Tables added route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface W.X.Y.0 0.0.0.0 255.255.255.0 U 0 0 0 br0 0.0.0.0 W.X.Y.1 0.0.0.0 UG 0 0 0 br0 C:>route print =========================================================================== Interface List 32...00 ff ac d6 f7 04 ......TAP-Win32 Adapter V9 15...00 14 d1 e9 57 49 ......Microsoft Virtual WiFi Miniport Adapter #2 14...00 14 d1 e9 57 49 ......Realtek RTL8191SU Wireless LAN 802.11n USB 2.0 Net work Adapter 10...00 1f d0 50 1b ca ......Realtek PCIe GBE Family Controller 1...........................Software Loopback Interface 1 11...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface 16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 17...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 18...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #3 36...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #5 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 10.1.2.1 10.1.2.201 25 10.1.2.0 255.255.255.0 On-link 10.1.2.201 281 10.1.2.201 255.255.255.255 On-link 10.1.2.201 281 10.1.2.255 255.255.255.255 On-link 10.1.2.201 281 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 10.1.2.201 281 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 10.1.2.201 281 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 10.1.2.1 Default =========================================================================== C:>tracert google.com Tracing route to google.com [74.125.71.147] over a maximum of 30 hops: 1 344 ms 345 ms 343 ms PC [W.X.Y.221] 2 * * * Request timed out.

  Read the article

• Windows XP/7: custom routing for VPN connection

  - by Peter Becker

  We are dealing with a badly configured VPN connection from a vendor, which set up the default gateway but doesn't route traffic anywhere beyond their VPN zone. I managed to do some ad-hoc routing to configure a computer in a way that it can reach the vendor's VPN, our local network as well as the internet. I then tried to turn this into a script, but that failed since the interface number of the VPN changes on every connection. Is there a way in Windows XP and/or Windows 7 to configure custom routing on the client side of a VPN connection? What I would like to do is to have a script running just after the connection comes up that changes the routing table (similar to an ifup script on UNIX).

  Read the article

• Setup VLAN agnostic ports on HP ProCurve 1810G (Ingress Filter, Trunking)

  - by Thomas

  I am wondering if it is possible to configure some ports of the web managed ProCurve Switch 1810G to participate in all VLAN traffic. Even if no VLAN with that ID has been set up inside the switch. The issue is that I have two virtualization servers that will use yet unknown VLANs of a certain range to communicate with each other. But the range is much larger than the 64 supported VLANs this switch can manage. The switch also offers static and LACP Link Trunks. But I guess there will also apply the Ingress Filter that drops packets with unconfigured VLAN IDs? A separate unmanaged switch that connects the two hosts and one ProCurve Port would work, but maybe I do not have to? Thanks

  Read the article

• Installing PHP 5.3 on a Windows host with both Apache and IIS

  - by Hippyjim

  I'm currently experimenting with a couple of configurations of Apache and IIS on the same server box - so far using Apache as a proxy for IIS is winning, but another of my setups has Apache on a non-standard port with IIS taking the majority of traffic. Both of these machines currently have PHP 5.2 installed. I want to upgrade to PHP 5.3, but the installer asks which server I'm running - I'm running both - so what do I tell it? Which configuration will be the most flexible, tell it we're running IIS, or tell it we're running Apache?

  Read the article

• iptables openvpn forward selectively from eth to tun

  - by Bryan Hunt

  Simple for those who know, indecipherable for those who don't... I'm running openVPN on (hypothetical) 66.66.66.66, I want to FORWARD incoming traffic, arriving on interface eth0 to interface tun0. It would also be nice to filter - based on destination IP address. I'm doing the NAT later on, but like to lock down early wherever possible. So onto the main course... This works: #Enable forwarding from eth0 to tun0 iptables -A FORWARD -i eth0 -o tun+ -j ACCEPT But this doesn't pass any packets whatsoever: #Stricter version iptables -A FORWARD -i eth0 -o tun+ --dst 66.66.66.66 -j ACCEPT Am I being unacceptably foolish?

  Read the article

• MaxClients, Server Limits etc

  - by Moe

  Hello, I'm having some problems with my Server. It's getting quite a bit of traffic and is very slow, and sometimes inaccessible by my users. Here are the server specs: CPU: Intel(R) Xeon(R) CPU E5620 @ 2.40GHz - 16 Processors RAM: 2GB The Values for the Apache Config are: StartServers: 5 MaxSpareServers: 10 MinSpareServers: 5 MaxClients: 150 ServerLimit: 256 MaxRequestsPerChild: 1000 KeepAlive: On KeepAliveTimeout: 5 MaxKeepAliveRequests: 100 TimeOut: 300 What would be optiminal values for a server of my configuration to support the maximum amount of users at a reasonable speed without killing the server! Thank you.

  Read the article

• Using airport extreme base station as a wireless G to wireless N bridge

  - by micmcg

  Due to unfortunate placement of various wall outlets in my new apartment, my adsl 2 modem + router is not able to be placed next to my airport extreme base station (AEBS). I'd prefer not to run cat5 cable between them, but I still want to use the wireless N on the AEBS, because it will have a high speed NAS plugged in via gigabit ethernet so I want to maximise the wireless transfer speed to my 27" iMac. Is it possible to use one of the radios in the airport extreme to bridge the wireless G network with the router, and the wireless N radio to broadcast normally? The only traffic going over the G network should be internet (24mbps ADSL2) so it should never get saturated. Thanks

  Read the article

• Incredibly high latency for Ubuntu guest on Hyper-V

  - by Mark Henderson

  I've got several Ubuntu 10.04 virtual machines running as Hyper-V guests on Windows Server 2008 R2 SP1 and they're all perfectly fine. Today I installed my first Ubuntu 11.10 virtual machine and I'm seeing rediculous pings: These servers are all connected via gigabit to a local LAN, with almost no network traffic at all1, with a legacy network adapter in Hyper-V. I'm a bit of an Ubuntu n00b so I don't really know where to go from here. Any ideas? free -m reports: total used free shared buffers cached Mem: 485 470 15 0 63 299 -/+ buffers/cache: 107 378 Swap: 507 20 487 This is within a few mb of our other Ubuntu servers that are on 10.04. I removed the Legacy NIC and installed a Synthetic one in Hyper-V and this did improve the numbers, in that they're around 10-30ms now, but I would still be expecting <1ms response times. 1As a comparison, I have another Ubuntu 10.04 guest on Hyper-V almost 1,000km away that has a ping of 33ms

  Read the article

• How difficult is it to setup Mac OS X Server?

  - by Anriëtte Combrink

  Hi there We are a small office of about 4 people, and we would like to have a 27-inch iMac (Core 2 Duo) setup as a server and workstation simultaneously, using Mac OS X Server. This might seem like overkill (and stupidity at the same time), but here is the situation: we want to convert our whole office to Mac, only one full-time PC left we will not use it's mail server we might use it's chat server we want it setup to provide VPN we are a small office so I don't see how the server can be overrun with too much traffic. How difficult would it be to set it up in this way? I have a fairly advanced knowledge of Mac OS X but have never encountered Mac OS X Server. I think I would be able to set it up, but what are the probable pitfalls that might come up? Has anyone else been in a similar situation?

  Read the article

• email handling with inbox.py and nginx

  - by Matt Ball

  I have a Flask web application running behind gunicorn and Nginx. Nginx proxies any traffic to ivrhub.org to the correct flask app. I would very much like to use inbox.py to process some incoming email. Running inbox.py's example on my server and then sending an email to [email protected] does not work as I intended. The inbox.py server does not seem to receive anything but the email also does not bounce. I'm missing something conceptually -- is there a DNS setting I need to configure or something I need to adjust with Nginx?

  Read the article

• Media Temple-like hosting services?

  - by antonpug

  I have a couple of wordpress sites which do not get much traffic now, but I plan on expanding to something like a 1000-2000visits/day in a year or two. Media Temple has some really nice offerings, but their Wordpress plan is 20/month...which is a little too much, seeing as at this point my site is more of a hobby than a money making machine. I currently host with HostGator (just switched from GodaddyiPageBluehost). All these cheaper/pop hosting services are okay, but it would be nice to find something a little bit more "premium", but at a lower cost than MT. Anyone know anything worth looking at?

  Read the article

• Will being a VPN Client interrupt web pages hosted by IIS?

  - by f1gm3nt3d

  We have a dedicated server that is primarily used to host our website. I've been tasked with determining the feasibility of setting up a VPN connection from it to our Internal Network at our offices for a few ease of use purposes. My concern is that if I establish this VPN connection our Website will only be available internally and not to the internet in general. I'm concerned about this because in everything I read the fact is stated that by default all network traffic is routed over the VPN connection when it's established, is this also true for applications such as IIS that are listening for incoming connections? TL;DR Will having a VPN Client up and running cause a problem with server applications that may be listening on the NIC connected to the Internet due to changes that VPN makes in the routing tables?

  Read the article

• pfsense multi-site VPN VOIP deployment

  - by sysconfig

  have main office pfsense firewall configured like this: local networks WAN - internet LAN - local network VOIP - IP phones need to connect remote offices (multi-users) and single remote users (from home) use IPSEC or OpenVPN to build "permanent" automatically connecting tunnels from remote location to main location. in remote locations, network will look like this: WAN - internet LAN - local network multiple users VOIP - multiple IP phones in order for the IP phones to work they have to be able to "see" the VOIP network and the VOIP server back at the main office for single remote users ( like from home ) the setup will be similar but only one phone and one computer so questions: best way to tie networks together? IPSEC or OpenVPN can this be setup to automatically connect ? any issues/suggestions with that design/topology ? QoS or issues with running the VOIP traffic over a VPN throughput, quality etc.. obviously depends on remote locations connection to some degree

  Read the article

• Windows 2008R2 blocks outbound LDAP for non-admins?

  - by Jon Bailey

  I've got a Windows 2008R2 terminal server with ~30 users on it. It's joined to a Samba-based domain. During the login script, we connect directly to the LDAP server to pull out certain profile information. This used to work just fine. Now, it doesn't, but only for non-local-admin accounts. Local admins work fine. As a non-local-admin: Connection to ports 389 or 636 just terminate (wireshark on the LDAP server reveals no connection attempt) Connection to other ports on the same server work fine Same thing on multiple LDAP servers Windows firewall is disabled Can't find any other rules/policies that may block this I suspect since this used to work, it came down during an update, but for the life of me, I can't find what. EDIT: I just ran Wireshark on the machine and didn't see anything when connecting to the LDAP server in question (or any LDAP server for that matter). I can, however, see traffic when I connect to that server on another port.

  Read the article

• Small web server hardware advice

  - by Dmitri

  We need to build a new web server for our organization. We have around 100 hundred small traffic web sites, so our hardware requirements are not too tough. We run CentOS 6, Varnish+Apache, PHP, MySQL, Typo3 CMS for most of websites. Here's a hardware we want to buy: SuperMicro X9SCA-F-O (we need to have a remote management capability) (or better X9SCM-F?) Intel Xeon E3-1220 v2 2*4Gb DDR-III 1600MHz Kingston ECC (KVR16E11/4) (currently we have 4gb, and it feels like enough, so no reason for 16gb yet). Procase EB140-B-0 (1 unit) PSU 350W Procase MG1350, Active PFC We already have: Intel 335 120GB SSD (for OS, databases and important websites). 2*2tb WD Green RAID1 (for other data and backups). Does it look like a reasonable choice for our needs? Any issues with hardware compatibility? Any other notes?

  Read the article

• Bridging VirtualBox over OpenVPN TAP adapter on Windows

  - by Sean Edwards

  I'm trying to configure a virtual machine (VirtualBox guest running Backtrack 4) with a bridged adapter over a VPN connection. The VPN is is hosted by the cybersecurity club at my university, and connects to a sandboxed LAN designed for penetration testing against various servers that the club has built. My host (Windows 7 Ultimate) connects to the VPN fine and is assigned an IP through DHCP, but for some reason the VM can't do the same thing, and I'm not sure why. It's like OpenVPN is filtering out packets from the MAC address it doesn't recognize. I want the virtual machine to bridge over the VPN connection, because our IT office has very strict policies about what you can and can't do on the network. I want to be able to run active attacks (ARP spoofing, nmap, Nessus scans) in the sandbox environment without risking the traffic accidentally going over the university network and getting my internet access revoked. Bridging over the VPN connection and running all attacks from inside the VM would solve that problem. Any idea why the host can use this interface, but the VM can't?

  Read the article

• High server load - [jbd2/md1-8] using 99.99% IO

  - by Alex

  I've been having spike in load over the last week. This usually occurs once or twice a day. I've managed to identify from iotop that [jbd2/md1-8] is using 99.99 % IO. During the high load times there is no high traffic to the server. Server specs are: AMD Opteron 8 core 16 GB RAM 2x2.000 GB 7.200 RPM HDD Software Raid 1 Cloudlinux + Cpanel Mysql is properly tuned Apart from the spikes, the load usually is around 0.80 at most. I've searched around but can't find what [jbd2/md1-8] does exactly. Has anyone had this problem or does anyone know a possible solution? Thank you. UPDATE: TIME TID PRIO USER DISK READ DISK WRITE SWAPIN IO COMMAND 16:05:36 399 be/3 root 0.00 B/s 38.76 K/s 0.00 % 99.99 % [jbd2/md1-8]

  Read the article

• How to restrict Apache Location directive to cetain sub-domain?

  - by ohho

  On our server www.example.com, we use the <Location> directive to proxy traffic to a back-end server: <Location /app1> ProxyPass http://192.168.1.20 </Location> Then we added a sub-domain uat.example.com which points to the same IP address of www.example.com. We want to use it as a proxy for client to test an app being developed. Hopefully, the client can access via: http:/uat.example.com/app2_uat Now if we add a Location: <Location /app2_uat> ProxyPass http://192.168.1.30 </Location> The client can access both: http:/www.example.com/app2_uat http:/uat.example.com/app2_uat How can I restrict Location such that only: http:/uat.example.com/app2_uat is accessible? (i.e. http:/www.example.com/app2_uat should not be accessible.)

  Read the article

• What is a usable throughput for a home media server

  - by Craig

  I am looking to setup a home server that will act as a media server. This will include both video (possibly HD) and audio. The clients will be a fun mix of hardware but that is a different question. What I want to know is what is the minimum throughput for streaming video without hitches? Is there a "sweet" spot for throughput (price vs. throughput)? I am determining my budget for this "upgrade" and I need to evaluate wether or not upgrading to a 1 Gbps home LAN is required. Sure, it would be sweet and easily handle the traffic but I don't want to do it unless it is necesary.

  Read the article

< Previous Page | 114 115 116 117 118 119 120 121 122 123 124 125  | Next Page >