Search Results

Search found 500 results on 20 pages for 'esxi'.

Page 12/20 | < Previous Page | 8 9 10 11 12 13 14 15 16 17 18 19  | Next Page >

• Data Store/Volume disconnecting. How to resume copy of VMDK?

  - by Serge

  I'm having an issue with my ESXi 4.1 hosts losing the datastore with FC SAN after a power outage. All 3 hosts disconnect so it's definitely a SAN issue. I've tried to resolve the issue on the SAN side with the SAN software support and Adaptec hardware support. No luck there. So I'm stuck with a SAN that will randomly disconnect the volume. I need to get the virtual machines (VMDK files) from the datastore. The problem is I can only get 5-20% before the data store disconnects. I have backups that are slightly older that I can use to replicate the VMDK differences to. What has not worked so far: Powering up the VMs, will boot up for 5-15 minutes then freeze vCenter migrate or clone of VM, will fail after similar period of time vCenter copy/paste of VMDK. Was able to get one 30GB VMDK and no luck after that. vMware Data Recovery. Fails at low %, can't resume, so next backup starts from begining. Veeam Backup & Recovery. Same as above, no resume function. If I can just find a backup solution that will resume from the failed spot that would solve my issue. Anyone have any ideas that I could try? EDIT 1 The SAN is Open-E DSS 6 running on a Supermicro 24 drive enclosure with 4 port Qlogic FC. Adaptec 52445 RAID card.

  Read the article

• RAID 10 or RAID 5 for multiple VMs - what is the best choice?

  - by Lars Fastrup

  I have just ordered a new rig for my business. We do a lot of software development for Microsoft SharePoint and need the rig to run several virtual machines for development and test purposes. We will be using the free VMware ESXi for virtualization. For a start, we plan to build and start the following VMs - all with Windows Server 2008 R2 x64: Active Directory server MS SQL Server 2008 R2 Automated Build Server SharePoint 2010 Server for hosting our public Web site and our internal Intranet for a few people. The load on this server is going to be quite insignificant. 2xSharePoint 2007 development server 2xSharePoint 2010 development server Beyond that we will need to build several SharePoint farms for testing purposes. These VMs will only be started when needed. The specs of the new rig is: Dell R610 rack server 2xIntel XEON E5620 48GB RAM 6x146GB SAS drives Dell H700 RAID controller We believe the new server is going to make our VMs perform a lot better than our existing setup (2xIntel XEON, 16GB RAM, 2x500 GB SATA in RAID 1). But we are not sure about the RAID level for the new rig. Should we go for having the the 6x146GB SAS drives in a RAID 10 configuration or a RAID 5 configuration? RAID 10 seems to offer better write performance and lower risk of a RAID failure. But it comes at a cost of less drive space. Do we need RAID 10 or would RAID 5 also be a good choice for us?

  Read the article

• Virtual machine lost after power cut

  - by dannymcc

  We have just had a power issue and our ESX (ESXi 4.1.0) host lost power and then rebooted. All but one of the virtual servers have rebooted with no problem, however one of them refused to power up. I try to power it on and I get the following error: File <unspecified filename> was not found Reason: The system cannot find the file specified. Cannot open the disk '/vmfs/volumes/4e03076e-90834647-b846-001185c38f42/LAMP- Stack/turnkey-lamp-11.3-lucid-x86.vmdk' or one of the snapshot disks it depends on. VMware ESX cannot find the virtual disk "/vmfs/volumes/4e03076e-90834647-b846- 001185c38f42/LAMP-Stack/turnkey-lamp-11.3-lucid-x86.vmdk". Verify the path is valid and try again. I have logged into the ESX host to see if the file is there an have found only the following file that matches the filename: /vmfs/volumes/4e03076e-90834647-b846-001185c38f42/LAMP-Stack/turnkey-lamp-11.3-l ucid-x86-s001.vmdk I notice that the above file has '-s001' after the filename. Is this recoverable? Any help of advice is greatly appreciated! EDIT: Running ls -l on the directory that contains the file shows this: drwxr-xr-t 1 root root 1680 Feb 9 09:49 4e03076e-90834647-b846-001185c38f42 The databrowser file system looks like this: and in a different directory there is the file that matches the missing one:

  Read the article

• File corruption (bad checksums) in large files copied to VMware guest

  - by AllanA

  In setting up a development lab, I've got a desktop system running ESXi 4.1.0 (free license) on SATA RAID 0 (already purchased and configured when I started this job; I'm open to hardware input as it pertains to my problem.) Its guests so far include two Win2008 Server R2 64-bit VMs and on Ubuntu 10.04 64-bit VM. I'm installing onto the Windows servers. We've been copying off some fairly large files (over a gigabyte) for an installation, hoping to install more quickly from a (virtual) hard drive than from the network for from BD-ROM. The problem is that they keep coming up with different checksums from the originals. The file sizes are the same, but md5sum reports different numbers (and so does the installer, as it refuses to continue when the checksums don't match.) I've tried copying directly from the BD-ROM (attaching the OS drive to the host system's physical drive). I've tried copying the large files onto a co-worker's Windows machine from his Blu-Ray drive; when I do that, the checksums match. But when I copy from his machine to the VM guest over a network share, the checksums no longer match. Thinking this meant a corrupt destination drive, I deleted it in vSphere and added another freshly created drive. The problem persists. I'm not sure what to try next.

  Read the article

• Drupal on an NFS share has terrible performance

  - by Marcus

  We have a setup where a Drupal 7 site with the following setup - a VMware ESXi 4.1 host server running a web vm and an NFS VM. The web VM is using Apache and mod_php. The site is still in development thus we have to turn off all forms of caching due to the frequently-updated files. Each page request takes around 15-20 seconds to complete. Profiling the PHP code shows that the vast majority of time (normally over 90%) is taking by all the is_dir(), is_file() function calls that load up the modules. I've increased PHP's realpath cache size to several megs and an strace shows that the lstat calls then drop from over 200 to around 6 and stat() decreases a bit (around 600 calls). However, while this has shaved off quite a bit of time, I am simply unable to break past the 10 second per request barrier. Is there a way to get better performance out of this setup that doesn't involve caching? Configs and stats: VMs: web - Centos 6 64bt, 2.5GB RAM, normal CPU/HD prioritisation nfs - Centos 6 64bt, 2GB RAM, normal CPU priority, high HD priority PHP: 32M realpath cache size (it's this high for testing purposes) NFS: ~]# egrep -v '#|^$' /etc/nfsmount.conf [ NFSMount_Global_Options ] Defaultvers=4 Ac=False Rsize=32k Wsize=32k Bsize=32k Reading speeds via NFS are not an issue a dd of a 100M test file using 32k blocks returns: 3200+0 records in 3200+0 records out 104857600 bytes (105 MB) copied, 1.84984 s, 56.7 MB/s real 0m1.857s user 0m0.007s sys 0m0.330s Strace on Apache process with empty realpath cache: % time seconds usecs/call calls errors syscall ------ ----------- ----------- --------- --------- ---------------- 50.78 1.157452 337 3434 28 stat 32.58 0.742656 628 1182 425 open 9.29 0.211788 762 278 1 lstat 3.17 0.072322 0 237865 write 2.45 0.055839 490 114 13 access 0.45 0.010262 43 237 brk 0.34 0.007725 10 811 74 read 0.28 0.006340 9 679 fstat 0.22 0.005069 18 281 poll 0.20 0.004533 6 698 getdents 0.09 0.001960 10 190 mmap 0.05 0.001065 14 74 accept4 0.04 0.001000 333 3 chdir 0.03 0.000750 4 190 munmap 0.01 0.000339 0 836 close 0.01 0.000247 3 75 writev 0.00 0.000068 0 611 fcntl 0.00 0.000063 1 77 shutdown 0.00 0.000000 0 1 lseek 0.00 0.000000 0 5 rt_sigaction 0.00 0.000000 0 1 rt_sigprocmask 0.00 0.000000 0 3 setitimer 0.00 0.000000 0 5 socket 0.00 0.000000 0 5 5 connect 0.00 0.000000 0 74 getsockname 0.00 0.000000 0 15 setsockopt 0.00 0.000000 0 5 getcwd 0.00 0.000000 0 1 futex ------ ----------- ----------- --------- --------- ---------------- Strace after realpaths are cached % time seconds usecs/call calls errors syscall ------ ----------- ----------- --------- --------- ---------------- 60.14 1.371006 484 2831 28 stat 31.79 0.724705 627 1155 425 open 3.53 0.080354 0 237865 write 2.65 0.060433 530 114 13 access 0.43 0.009913 99 100 brk 0.38 0.008730 11 804 74 read 0.35 0.007910 12 675 fstat 0.30 0.006775 10 654 getdents 0.13 0.003065 11 281 poll 0.09 0.002000 333 6 1 lstat 0.07 0.001545 2 807 close 0.05 0.001063 14 74 accept4 0.04 0.001000 6 179 mmap 0.02 0.000404 2 179 munmap 0.01 0.000271 4 75 writev 0.01 0.000212 0 611 fcntl 0.01 0.000129 2 77 shutdown 0.00 0.000022 0 74 getsockname 0.00 0.000000 0 1 lseek 0.00 0.000000 0 5 rt_sigaction 0.00 0.000000 0 1 rt_sigprocmask 0.00 0.000000 0 3 setitimer 0.00 0.000000 0 3 socket 0.00 0.000000 0 3 3 connect 0.00 0.000000 0 15 setsockopt 0.00 0.000000 0 5 getcwd 0.00 0.000000 0 3 chdir ------ ----------- ----------- --------- --------- ---------------- Mount: nfs.xxx.xxx.xxx:/path/to/website/files on /path/to/website/files type nfs (rw,hard,intr,noac,vers=4,addr=xx.xx.xx.xx,clientaddr=xx.xx.xx.xx) Any help is, naturally, appreciated.

  Read the article

• ESXi Server with 12 physical cores maxed out with only 8 cores assigned in virtual machines

  - by Sam

  I have an ESXi 5 server running on a 2-processor, 12-core system with hyperthreading enabled. So: 12 physical cores, 24 logical ones. On this server are 4 Windows 7 VMs, each configured for 2 processors, each running VMware Tools. Looking at my stats in vSphere, my "core utilization" is constantly maxed out. Yes, these machines are working hard, but only 8 cores have been allocated. How is this possible? Should I look into reducing the processor count per machine as in this post: VMware ESX server? I checked to ensure that hardware virtualization is enabled in the BIOS of the machine (a DELL R410). I've also started reading up on configuration, but being a newbie there's a lot of material to catch up on. It also seems I should only bother with advanced settings and pools if I'm really pushing the load, and I don't think that I should be pushing it with so few VMs. I suspect that I have some basic, incorrect configuration setting, but it's also possible that I have some giant misconceptions about virtualization. Any pointers? EDIT: Given the responses I've gotten so far, it seems that this is a measurement problem and not a configuration problem, making this less critical. Perhaps the real question is: How does the core utilization of the server reach a higher percentage than all individual cores' core utilization, and given that this possibility makes the metric useless for overall server load, what is the best global metric for measuring CPU load on hyper-threaded systems?

  Read the article

• Dual Monitor support rdp 7 to win 7 on esxi

  - by rphilli5

  I am trying to RDP from a Windows 7 Professional dual monitor physical machine to a Windows 7 Professional VM hosted on esxi 4.0. I can get the spanning option to work to both monitors, but I have tried 3 different methods of connecting but have not been able to use true multiple monitors. At different times, I tried checking the "use all monitors" option, command line mstsc /multimon and added the line use multimon:i:1 to the .rdp file. None of these worked. Any ideas? The physical machine can connect to other Windows 7 physical machines with true multi monitor access. I also have the same issue when going from a 32bit RC1 machine to a Windows 7 Professional x64, but not when going in the reverse direction. Here's the .rdp: screen mode id:i:2 use multimon:i:1 desktopwidth:i:1440 desktopheight:i:900 session bpp:i:16 winposstr:s:0,1,341,118,1139,568 compression:i:1 keyboardhook:i:2 audiocapturemode:i:0 videoplaybackmode:i:1 connection type:i:1 displayconnectionbar:i:1 disable wallpaper:i:1 allow font smoothing:i:0 allow desktop composition:i:0 disable full window drag:i:1 disable menu anims:i:1 disable themes:i:1 disable cursor setting:i:0 bitmapcachepersistenable:i:1 full address:s:192.168.1.5 audiomode:i:0 redirectprinters:i:1 redirectcomports:i:0 redirectsmartcards:i:1 redirectclipboard:i:1 redirectposdevices:i:0 redirectdirectx:i:1 autoreconnection enabled:i:1 authentication level:i:2 prompt for credentials:i:0 negotiate security layer:i:1 remoteapplicationmode:i:0 alternate shell:s: shell working directory:s: gatewayhostname:s: gatewayusagemethod:i:4 gatewaycredentialssource:i:4 gatewayprofileusagemethod:i:0 promptcredentialonce:i:1 use redirection server name:i:0 drivestoredirect:s:

  Read the article

• Rescue system running TFS that BSODs, into vmware esxi

  - by 3molo

  Hi, After moving to new facilities, one of our old Dell servers running Windows Server 2003 R2 on PowerEdge 2650 HW BSODs with 0x8e. The server runs Team Foundation Server, so we have a few guys dependent on it. No one here knows TFS, so we have no idea how difficult it would be to setup from scratch. We have the MSSQL database(s) backed up, recent and fresh copy. Tried removing/refitting memory modules, but with no success. The system boots into safe mode but hangs occasionally. I booted a linux livecd and did a dd of both c: and d:, so I have all the data in compressed images on a vmware machine. For the guest, I created a 38G (actually it became 40GB) partition to act as C:, and booted a live cd. I then uncompressed the compressed disk image of c: and dd'd it to the new c: using 'gunzip -dc c.img.gz | dd of=/dev/sda1 bs=1M'. The operation ran for about 1000 seconds, and completed successfully. I assumed it would at least try to boot windows (but most likely BSOD due to not having correct drivers), but the Vmware ESXi guest does not seem to recognize it as a bootable disk. We don't have the vmware enterprise license, so the vmware converter cold cloning is not an option. Did I do something wrong in my dd's etc with the ISOs, or why would it not (try to) boot? Am I wasting my time? What other approach is there? Will continue to try to remove services and drivers to make the physical machine at least work reasonably well in safe mode. What do you suggest? 1. Continue to get the dd'd images to the virtual disk and get it to boot. 2. Install a new windows server, get team foundation server and restore from backup. 3. Focus on the old problematic hardware Any help appreciated

  Read the article

• Windows XP VM on VMWare ESXi 4.1 "pausing" / blocked occasionally

  - by FelixD

  We have an issue with Windows XP SP3 VMs on VMWare ESXi 4.1.0 (the free version): They sometimes seem to "pause" for several minutes. This happens rarely (maybe once a month per VM, at least noticed only that often), but still is an issue for us. It happens for three different but similar VMs on three pretty different hosts (different hardware). I have the feeling that the "pausing" is not actually the CPU blocking, but probably the harddisks, but not 100% sure. The servers have one IDE disk (C:) and one SCSI (D:) and it might be either of the two. I have seen scheduled tasks simply not starting for up to 9 minutes and then running normally again with normal speed. They were totally blocked. This is not a load issue, the VMWare hosts have average load and the VMs in question already have reserved CPU resources plus high priorities for CPU and disk. The Windows boxes run mainly MySQL, Tomcat, FileZilla server, Cygwin stuff, Java + R applications, VMWare client, Elusiva Terminal Server pro, Nagios client. Not sure if this might be related with any of that software (e.g. Elusiva). Trying to debug this, there was nothing visible in Windows Event log, other logs in C:\Windows, VMWare events etc. Unfortunately the vmware.log file ends with "Log throttled". We found that we ran into 2 VMWare bugs there: The VMWare client writes lots on bogus messages in the vmware.log, which we now disabled (log level error setting) plus the bug that VMWare does not unthrottle the log (at least so far despite VM reboots). I know there is not much guidance and that may also be the reason why I so far didn't find anything related on the web or on ServerFault, but maybe some of this rings a bell with someone? Or please direct me to what more info to post. I hope that the vmware.logs get unthrottled eventually (can't easily restart the hosts at the moment). Thanks for any input!

  Read the article

• arp problems with transparent bridge on linux

  - by Mink

  I've been trying to secure my virtual machines on my esx server by putting them behind a transparent bridge with 2 interfaces, one in front, one at the back. My intention is to put all the firewall rules in one place (instead of on each virtual server). I've been using as bridge a blank new virtual machine based on arch linux (but I suspect it doesn't matter which brand of linux it is). What I have is 2 virtual switchs (thus two Virtual Network, VN_front and VN_back), each with 2 types of ports (switched/separated or promiscious/where the machine can see all packets). On my bridge machine, I've set up 2 virtual NIC, one on VN_front, one on VN_back, both in promisc mode. I've created a bridge br0 with both NIC in it: brctl addbr br0 brctl stp br0 off brctl addif br0 front_if brctl addif br0 back_if Then brought them up: ifconfig front_if 0.0.0.0 promisc ifconfig back_if 0.0.0.0 promisc ifconfig br0 0.0.0.0 (I use promisc mode, because I'm not sure I can do without, thinking that maybe the packets don't reach the NICs) Then I took one of my virtual server sitting on VN_front, and plugged it to VN_back instead (that's the nifty use case I'm thinking about, being able to move my servers around just by changing the VN they are plugged into, without changing anything in the configuration). Then I looked into the macs "seen" by my addressless bridge using brctl showmacs br0 and it did show my server from both sides: I get something that looks like this : port no mac addr is local? ageing timer 2 00:0c:29:e1:54:75 no 9.27 1 00:0c:29:fd:86:0c no 9.27 2 00:50:56:90:05:86 no 73.38 1 00:50:56:90:05:88 no 0.10 2 00:50:56:90:05:8b yes 0.00 << FRONT VN 1 00:50:56:90:05:8c yes 0.00 << BACK VN 2 00:50:56:90:19:18 no 13.55 2 00:50:56:90:3c:cf no 13.57 the thing is that the server that are plugged in front/back are not shown on the correct port. I suspect some horrible thing happening in the ARP-world... :-/ If I ping from a front virtual server to a back virtual server, I can only see the back machine if that back machine pings something in the front. As soon as I stop the ping from the back machine, the ping from the front machine stops getting through... I've noticed that if the back machine pings, then its port on the bridge is the correct one... I've tried to play with the arp_ switch of /proc/sys, but with no clear effect on the end result... /proc/sys/net/ipv4/ip_forward doesn't seem to be of any use when using a bridge (seems it's all taken care of by brctl) /proc/sys/net/ipv4/conf//arp_ don't seem to change much either... (tried arp_announce to 2 or 8 - like suggested elsewhere - and arp_ignore to 0 or 1 ) All the examples I've seen have a different subnet on either side like 10.0.1.0/24 and 10.0.2.0/24... In my case I want 10.0.1.0/24 on both side (just like a transparent switch - except it's a hidden fw ). Turning stp on/off doesn't seem to have any impact on my issue. It's as if the arp packets where getting through the bridge, corrupting the other side with false data... I've tried to use the -arp on each interface, br0, front, back... it breaks the thing altogether... I suspect it has something to do with both side being on the same subnet... I've thought about putting all my machine behind the fw, so as to have all the same subnet at the back... but I'm stuck with my provider's gateway standing at the front with part of my subnet (in fact 3 appliance to route the whole subnet), so I'll always have ips from the same subnet on both side, whatever I do... (I'm using fixed front IPs on my delegated subnet). I'm at a loss... -_-'' Thx for your help. (As anyone tried something like this? from within ESXi?) (It's not just a stunt, the idea is to have something like fail2ban running on some servers, sending their banned IP to the bridge/fw so that it too could ban them - saving all the other servers from that same attacker in one go, allowing for some honeypot that would trigger the fw from any kind of suitable response, and stuffs of the sort... I am aware I could use something like snort, but it addresses some completely different kind of problems, in a completely different way... )

  Read the article

• GhettoVCB.sh log is wrong

  - by Michael

  2010-02-25 16:03:02 -- info: CONFIG - VM_BACKUP_ROTATION_COUNT = 2 2010-02-25 16:03:02 -- info: CONFIG - DISK_BACKUP_FORMAT = thin 2010-02-25 16:03:02 -- info: ============================== ghettoVCB LOG START ============================== 2010-02-25 16:03:02 -- info: CONFIG - ADAPTER_FORMAT = buslogic 2010-02-25 16:03:02 -- info: CONFIG - POWER_VM_DOWN_BEFORE_BACKUP = 0 2010-02-25 16:03:02 -- info: CONFIG - ENABLE_HARD_POWER_OFF = 0 2010-02-25 16:03:02 -- info: CONFIG - VM_BACKUP_VOLUME = /vmfs/volumes/nfs_storage_backup/vm1 2010-02-25 16:03:02 -- info: CONFIG - ITER_TO_WAIT_SHUTDOWN = 3 2010-02-25 16:03:02 -- info: CONFIG - VM_BACKUP_ROTATION_COUNT = 2 2010-02-25 16:03:02 -- info: CONFIG - POWER_DOWN_TIMEOUT = 5 2010-02-25 16:03:02 -- info: CONFIG - DISK_BACKUP_FORMAT = thin 2010-02-25 16:03:02 -- info: CONFIG - SNAPSHOT_TIMEOUT = 15 2010-02-25 16:03:02 -- info: CONFIG - ADAPTER_FORMAT = buslogic 2010-02-25 16:03:02 -- info: CONFIG - LOG_LEVEL = info 2010-02-25 16:03:02 -- info: CONFIG - BACKUP_LOG_OUTPUT = /tmp/ghettoVCB.log 2010-02-25 16:03:02 -- info: CONFIG - POWER_VM_DOWN_BEFORE_BACKUP = 0 2010-02-25 16:03:02 -- info: CONFIG - ENABLE_HARD_POWER_OFF = 0 2010-02-25 16:03:02 -- info: CONFIG - ITER_TO_WAIT_SHUTDOWN = 3 2010-02-25 16:03:02 -- info: CONFIG - VM_SNAPSHOT_MEMORY = 0 2010-02-25 16:03:02 -- info: CONFIG - VM_SNAPSHOT_QUIESCE = 0 2010-02-25 16:03:02 -- info: CONFIG - POWER_DOWN_TIMEOUT = 5 2010-02-25 16:03:02 -- info: CONFIG - VMDK_FILES_TO_BACKUP = all 2010-02-25 16:03:02 -- info: CONFIG - SNAPSHOT_TIMEOUT = 15 2010-02-25 16:03:02 -- info: CONFIG - LOG_LEVEL = info 2010-02-25 16:03:02 -- info: CONFIG - BACKUP_LOG_OUTPUT = /tmp/ghettoVCB.log 2010-02-25 16:03:02 -- info: CONFIG - VM_SNAPSHOT_MEMORY = 0 2010-02-25 16:03:02 -- info: CONFIG - VM_SNAPSHOT_QUIESCE = 0 2010-02-25 16:03:02 -- info: CONFIG - VMDK_FILES_TO_BACKUP = all 2010-02-25 16:03:13 -- info: Initiate backup for VM1 2010-02-25 16:03:13 -- info: Initiate backup for VM1 2010-02-25 16:03:13 -- info: Creating Snapshot "ghettoVCB-snapshot-2010-02-25" for VM1 2010-02-25 16:03:13 -- info: Creating Snapshot "ghettoVCB-snapshot-2010-02-25" for VM1 Failed to clone disk : The file already exists (39). Destination disk format: VMFS thin-provisioned Cloning disk '/vmfs/volumes/datastore1/machine/VM1.vmdk'... 2010-02-25 16:04:16 -- info: Removing snapshot from VM1 ... Destination disk format: VMFS thin-provisioned Cloning disk '/vmfs/volumes/datastore1/machine/VM1.vmdk'... How can I fix this issue, the backup is working, but the log shows something like 2 back-up's in the exact time?

  Read the article

• Hardware firewall vs VMWare firewall appliance

  - by Luke

  We have a debate in our office going on whether it's necessary to get a hardware firewall or set up a virtual one on our VMWare cluster. Our environment consists of 3 server nodes (16 cores w/ 64 GB RAM each) over 2x 1 GB switches w/ an iSCSI shared storage array. Assuming that we would be dedicating resources to the VMWare appliances, would we have any benefit of choosing a hardware firewall over a virtual one? If we choose to use a hardware firewall, how would a dedicated server firewall w/ something like ClearOS compare to a Cisco firewall?

  Read the article

• kickstart: reference floppy drive via %ksappend or %include

  - by virtualeyes

  Having trouble getting %ksappend or %include to work when referencing a local floppy drive. Booting off remote server's cd-rom drive I am able to load the CentOS 6 minimal install image, and then add ks=hd:fd0/ks-jvm.cfg to boot params to load kickstart init file from floppy disk. That works fine. The problem is that I want to load a streamlined generic init file off the floppy and then, within the init, %ksappend or %include specific config files relative to the type of server I'm building (JVM, MySQL, Apache, etc.) I do not have DHCP, networking needs to be specified statically, so %ksappend and %include both fail when attempting to reference http://some-LAN-IP/foo.cfg since networking has not yet been set. The kickstart setup only works when I glob in the entire config into a single file, which is great, but ugly and difficult to maintain when I return later, having forgotten the original setup. At this point I'd be happy if I could get %ksappend or %include working with a floppy drive reference in the %post section; that would consolidate a lot of common boilerplate that all kickstarts will rely on (sshd_config, rsync config, resolve.conf, and so on) Thanks for providing the magic floppy drive reference that is eluding me!

  Read the article

• OpenIndiana (illumos): vmxnet3 interface lost on reboot

  - by protomouse

  I want my VMware vmxnet3 interface to be brought up with DHCP on boot. I can manually configure the NIC with: # ifconfig vmxnet3s0 plumb # ipadm create-addr -T dhcp vmxnet3s0/v4dhcp But after creating /etc/dhcp.vmxnet3s0 and rebooting, the interface is down and the logs show: Aug 13 09:34:15 neumann vmxnet3s: [ID 654879 kern.notice] vmxnet3s:0: getcapab(0x200000) -> no Aug 13 09:34:15 neumann vmxnet3s: [ID 715698 kern.notice] vmxnet3s:0: stop() Aug 13 09:34:17 neumann vmxnet3s: [ID 654879 kern.notice] vmxnet3s:0: getcapab(0x200000) -> no Aug 13 09:34:17 neumann vmxnet3s: [ID 920500 kern.notice] vmxnet3s:0: start() Aug 13 09:34:17 neumann vmxnet3s: [ID 778983 kern.notice] vmxnet3s:0: getprop(TxRingSize) -> 256 Aug 13 09:34:17 neumann vmxnet3s: [ID 778983 kern.notice] vmxnet3s:0: getprop(RxRingSize) -> 256 Aug 13 09:34:17 neumann vmxnet3s: [ID 778983 kern.notice] vmxnet3s:0: getprop(RxBufPoolLimit) -> 512 Aug 13 09:34:17 neumann nwamd[491]: [ID 605049 daemon.error] 1: nwamd_set_unset_link_properties: dladm_set_linkprop failed: operation not supported Aug 13 09:34:17 neumann vmxnet3s: [ID 654879 kern.notice] vmxnet3s:0: getcapab(0x20000) -> no Aug 13 09:34:17 neumann nwamd[491]: [ID 751932 daemon.error] 1: nwamd_down_interface: ipadm_delete_addr failed on vmxnet3s0: Object not found Aug 13 09:34:17 neumann nwamd[491]: [ID 819019 daemon.error] 1: nwamd_plumb_unplumb_interface: plumb IPv4 failed for vmxnet3s0: Operation not supported on disabled object Aug 13 09:34:17 neumann nwamd[491]: [ID 160156 daemon.error] 1: nwamd_plumb_unplumb_interface: plumb IPv6 failed for vmxnet3s0: Operation not supported on disabled object Aug 13 09:34:17 neumann nwamd[491]: [ID 771489 daemon.error] 1: add_ip_address: ipadm_create_addr failed on vmxnet3s0: Operation not supported on disabled object Aug 13 09:34:17 neumann nwamd[491]: [ID 405346 daemon.error] 9: start_dhcp: ipadm_create_addr failed for vmxnet3s0: Operation not supported on disabled object I then tried disabling network/physical:nwam in favour of network/physical:default. This works, the interface is brought up but physical:default fails and my network services (e.g. NFS) refuse to start. # ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 vmxnet3s0: flags=1004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:1: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:2: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:3: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:4: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:5: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:6: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:7: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 vmxnet3s0:8: flags=1004842<BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 9000 index 2 inet 192.168.178.248 netmask ffffff00 broadcast 192.168.178.255 lo0: flags=2002000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv6,VIRTUAL> mtu 8252 index 1 inet6 ::1/128 vmxnet3s0: flags=20002000840<RUNNING,MULTICAST,IPv6> mtu 9000 index 2 inet6 ::/0 # cat /var/svc/log/network-physical\:default.log [ Aug 16 09:46:39 Enabled. ] [ Aug 16 09:46:41 Executing start method ("/lib/svc/method/net-physical"). ] [ Aug 16 09:46:41 Timeout override by svc.startd. Using infinite timeout. ] starting DHCP on primary interface vmxnet3s0 ifconfig: vmxnet3s0: DHCP is already running [ Aug 16 09:46:43 Method "start" exited with status 96. ] NFS server not running: # svcs -xv network/nfs/server svc:/network/nfs/server:default (NFS server) State: offline since August 16, 2012 09:46:40 AM UTC Reason: Service svc:/network/physical:default is not running because a method failed. See: http://illumos.org/msg/SMF-8000-GE Path: svc:/network/nfs/server:default svc:/milestone/network:default svc:/network/physical:default Reason: Service svc:/network/physical:nwam is disabled. See: http://illumos.org/msg/SMF-8000-GE Path: svc:/network/nfs/server:default svc:/milestone/network:default svc:/network/physical:nwam Reason: Service svc:/network/nfs/nlockmgr:default is disabled. See: http://illumos.org/msg/SMF-8000-GE Path: svc:/network/nfs/server:default svc:/network/nfs/nlockmgr:default See: man -M /usr/share/man -s 1M nfsd Impact: This service is not running. I'm new to the world of Solaris, so any help solving would be much appreciated. Thanks!

  Read the article

• NAS4Free disk encryption and ZFS error

  - by MiNT

  I have installed a NAS4Free on a VM, and as recommended, i installed it on a 1GB virtual disk, and assigned another disk 500GB to this VM for file storage. I have created the disk, encrypted it, created a ZFS virtual disk, and then a ZFS storage pool. Everything was working. On every restart of this VM i needed to go on and mount the encrypted drive. Recently i upgraded the host machine, and now i cant mount or make it work. I have tried removing everything and setting up from scratch everything, with the exception of formating the disk, i have used an encrypted one without formating it. Does anybody have any suggestion on how can i at least get back my data, can i mount somehow the encrypted drive even in another utility, just need to get back the data that were on it.

  Read the article

• Why is vCenter 5.1u1 exiting hosts from maintenance mode?

  - by Shane Madden

  This vCenter server was just upgraded to 5.1 update 1. I'm going through hosts and bringing firmware up to date, then upgrading them from various versions of 5.0 to 5.1u1. vCenter 5.1u1 seems to have an interesting new behavior: it's removing hosts from maintenance mode when they reconnect after being disconnected -- but very inconsistently, I've seen it maybe 4 or 5 times on ~25-30 host reboots. I've only seen it happen on 5.0 hosts that have not yet been upgraded to 5.1. In the image, I placed the host in maint mode and rebooted it into the HP SPP DVD's automatic update mode. After its usual ~40 minute update process, the host came back online.. and 7 seconds before even logging that the host had reconnected, vCenter had sent the host a task to exit maintenance mode. In my understanding, the only time vCenter should drop a host out of maintenance mode is when vCenter put it into maintenance mode itself (such as a VUM upgrade task). Why would this vCenter be unilaterally exiting a host from user-initiated maintenance mode? Edit, additional info: I ran the firmware upgrades on 5 more hosts, all at the same time. Two of them exited maint mode after reconnecting, three did not. The common factor of those exiting maint mode seems to be how long they were offline; the two that took a few tries to boot to the virtual media are the two that got knocked out of maint mode. esx31 (image above): 45 minutes unresponsive esx19 (exited maint): 87 minutes unresponsive esx24 (stayed in maint): 32 minutes unresponsive esx29 (stayed in maint): 39 minutes unresponsive esx32 (stayed in maint): 30 minutes unresponsive esx34 (exited maint): 70 minutes unresponsive Edit: The disconnect time idea seems to have been a red herring, as it's not happening consistently. Additionally, in the vpxd.log the exit maint mode task initiation seems to always immediately follow this vim.EnvironmentBrowser.queryProvisioningPolicy SOAP call. Here's the lines, slightly trimmed for clarity: 15:27:49.535 [info 'vpxdvpxdVmomi'] [ClientAdapterBase::InvokeOnSoap] Invoke done (esx31, vim.EnvironmentBrowser.queryProvisioningPolicy) 15:27:49.560 [info 'commonvpxLro'] [VpxLRO] -- BEGIN task -- esx31 -- HostSystem.exitMaintenanceMode -- Note that on the nodes that don't get the exit task, the vim.EnvironmentBrowser.queryProvisioningPolicy event still occurs. I'm not seeing any other differences in events before or after this in the reconnect process, aside from the extra events caused by exiting maintenance mode. Given the log's mention of provisioning policies, looking for autodeploy-related maintenance mode issues turns up complaints about similar behavior (though I'm not using autodeploy at all).

  Read the article

• VLAN ID 4095 for guest VLAN tagging

  - by user121282

  Just want to know if it's true that if you use the VLAN ID 4095 for guest VLAN tagging, then vMotion will not work correctly as there is nowhere to pass back the reverse arp to? So, the problem we have noticed is when we have vmotioned VM's that are tagged on our trunk network, you cannot ping them from anywhere between 30-300 seconds. The hosts don't know which VLAN the guest is on. Is this right and also the correct behaviour? Thanks

  Read the article

• Nested RDP and ILO/VMWare console sessions, latency and keystroke repetition

  - by ewwhite

  I'm working on a remote server installation entirely through ILO. Due to the software application and environment, my access is restricted to a Windows server that I must access through RDP. Going from that system to the target server is accomplished via HP ILO2 or ILO3. I'm trying to run a CentOS installation in an environment where I can't use a kickstart. I'm doing this via text mode, but the keystrokes are repeating randomly and it's difficult to select the proper installation options. For example: ks=http://all.yourbase.org/kickstart/ks.cfg ends up looking like: ks====httttttp://allll..yourbaseee.....org/kicksstart/ks.cccfg I'm doing this using Microsoft's native RDP client (on Mac and Windows). I've also noticed this before when running installations or doing remote work in nested sessions. Same for typing into a VMWare console in some cases. Is there a nice fix for this, or it it simply a function of the protocol(s)?

  Read the article

• How to control admission policy in vmware HA?

  - by John

  Simple question, I have 3 hosts running 4.1 Essentials Plus with vmware HA. I tried to create several virtual machines that filled 90% of each server's memory capacity. I know that vmware has really sophisticated memory management within virtual machines, but I do not understand how the vCenter can allow me even to power on the virtual machines that exceed the critical memory level, when the host failover can be still handled. Is it due to the fact that virtual machines does not use the memory, so that it is still considered as free, so virtual machines can be powered on ? But what would happen if all VMs would be really using the RAM before the host failure - they could not be migrated to other hosts after the failure. The default behaviour in XenServer is that, it automatically calculates the maximum memory level that can be used within the cluster so that the host failure is still protected. Vmware does the same thing ? The admission policy is enabled. Vmware HA enabled.

  Read the article

• Steps after installing vCenter Server?

  - by goober

  I'm working with: Two new ESX servers that I'm configuring A new Server 2008 R2 machine that I'm using for vCenter. I took the following steps: Installed the Hypervisor on the 2 ESX machines Checked their setup/connectivity (appears to be fine; can ping, etc.) Installed vCenter Server on the Win2k8R2 box. This included the install of a SQL Express database (we're a small shop) FYI, I changed some of the ports (443 -- 8443, 80 --8080, etc.) Installed vCenter Web Client Server on the Win2k8R2 box Problems my vSphere Client on my Desktop fails to connect. Part of this is that it asks me for a username and password, but I don't recall specifying one when I set up the install. I receive the error "vSphere Client could not connect to [machinename]. An unknown connection error occurred. (The request failed because of a connection failure. (Unable to connect to the remote server))" I have also tried to use local machine admin credentials, including the format machinename\localuseracct. I have also tried using my domain credentials which are an admin for that box. I have also checked and the service is running. I also tried to connect via vSphere client locally installed on the server. It translates "localhost" to the correct name but gives the same error. I cannot register the vCenter server from the vCenter Web Client Server. I'm not sure if this is necessary, as they're both on the same machine, but it seems like the logical next step. I also receive a "failed to connect" error in this case as well. FYI, both the vCenter server and the vCenter Web Client Server are installed on the same Win2k8R2 server. What am I missing here? What is the best way to test in this case?

  Read the article

• VMware Virtualisation - Convert 64bit Windows Server to 32bit VM?

  - by dannymcc

  I have just started playing around with Vmware sphere and have the hypervisor OS installed on a spare HP ProLiant DL360 G4. I have created a test virtual machine running Ubuntu which has worked well. As a test project I wanted to convert a powered on server running Windows Server 2008 64bit into a virtual machine. As soon as I ran the Vmware Go software to start the conversion it became apparent that I cannot run 64bit guest OS's on that particular server. So, is there a way of migrating 64bit to 32bit during the conversion?

  Read the article

• Virtual (ESXi4) Win 2k8 R2 server hangs when adding role(s)

  - by Holocryptic

  I'm trying to provision a 2k8r2 Enterprise server in ESXi4. The OS installation goes fine, VMware tools, adding to domain, updates. All the basic stuff before you start adding Roles and Features. I've had this happen on two attempts already, and I'm not sure where the problem might be. I don't think it's hardware, because I have another 2k8r2 Standard server that's running fine. The only real difference is the install media. The server that's working was installed using a trial ISO and license. The one I'm having problems with is a full MAK installation. When I go to add a Role (the last case was Application Server) it gets all the way to "collecting installation results" before it hangs. CPU utilization in the vSphere client shows little spikes of activity with flatlines inbetween, but the whole console is locked up. The only way to release it is to power off and bring it back up. When you go to look at the added roles after bringing it back up, it shows that it is installed, but I don't trust that something didn't get wedged in all of that. The first install I did was with Thin Disk provisioning. The second attempt was with regular disk provisioning. In both cases 4GB of RAM, 2 vCPUs. VMware host is a HP Proliant DL380 G6, RAID-1 OS, RAID-5 data volume. 12 GB RAM. Has anyone else had this problem, or know where I should start poking around?

  Read the article

• Multi-Tenant VMWare View Deployment

  - by SimonJGreen

  We have VMWare View 5 set up for a single tenant environment, absolutely brilliant and works perfectly. Two thumbs up there! We're looking at the possibility of deploying this in a multi tenant scenario, where multiple unlinked companies connect to a VDI solution hosted by us but have no visibility of each other. Obviously;y this could be achieved by doubling up on all the components, having a complete VMWare View stack for each tenant, but this seems a little bit messy. Has anyone done this before, and if so how? Googling sheds little light apart from this experts exchange topic.

  Read the article

• Sizing a Virtual Server

  - by vdubs

  I would like to replace four aging physical servers with one virtual server. What is the best way to insure the VM server is sized correctly? The requirements of the apps that will be running on the four servers are APPLICATION SERVERS - QTY 3 - These will run the application layer for the web server, Business Objects Business Intelligence app, and various other small client server apps. The three most heavy hitting apps each have the following server requirements. So, if I bought three physical servers, this would be the requirements for each of them Processor - Dual 2.83 GHZ (or faster) Ram - 4 GB Raid 5 - 50-100GB usable space NIC - 1 GB Web Server - this will run one asp.net e-business app that will talk to our dedicated SQL server and the three app servers above. The E-Business software has these requirements for the web server Processor - Quad 2.83 GHZ (or faster) Ram - 8 GB Raid 5 - 50-100GB usable space NIC - 1 GB What is the best tool to determine what I need from a hardware standpoing in a virtual server? I am planning on using VMWare.

  Read the article

• Vmware sphere setting up external network

  - by Tom Beech

  I've just setup vmware vsphere 5 on a remote server (rented dedicated server). I've added my first VPS (centos 5.8) barebones. It's not finding any IP (internal or external) on boot. I've had an extra external IP assigned to my server that I wanted to use on the VPS. I tried editing the eth0 config and adding the IP in there and turning off the DHCP, but it can't find any IP or ping google or do any networking type things. How do I route the IP to my VPS so I can access it remotely?

  Read the article

< Previous Page | 8 9 10 11 12 13 14 15 16 17 18 19  | Next Page >