Search Results

Search found 11207 results on 449 pages for 'ip ban'.

Page 12/449 | < Previous Page | 8 9 10 11 12 13 14 15 16 17 18 19  | Next Page >

• Can't get my Raspberry Pi to keep a static IP

  - by JonnyIrving

  I recently got given a Raspberry Pi and I would like to be able to remote into it using puTTy from my laptop so I don't have to sit next to my tv with a keyboard and mouse to use it. I am able to get a puTTy session going when I know the IP address that my router has given the Pi on each session but it keeps changing on each reboot as I would expect. So I followed a number if instruction to go about configuring the RPi to keep a static IP address. This involved changing the file at '/etc/netwrok/interfaces' which now contains (password removed): auto lo iface lo inet loopback iface eth0 inet static address 192.168.1.82 netmask 255.255.255.0 gateway 192.168.1.254 auto wlan0 allow-hotplug wlan0 iface wlan0 inet dhcp wpa-ssid "BeBoxD304BF" wpa-psk "**********" Despite this however, each time I reboot my RPi it gives me a new dynamic IP address still. I also noticed that in the 'ifconfig' output below that the details of the eth0 doesn't contain IP details for inet addr, Bcast or Mask which have been present in all other examples I have seen online. eth0 Link encap:Ethernet HWaddr b8:27:eb:b5:95:da UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 00:87:c6:00:33:77 inet addr:192.168.1.83 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:918 errors:0 dropped:0 overruns:0 frame:0 TX packets:277 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 Also I'm not sure if this is relevant but it can't hurt! The file at '/etc/resolv.conf' contains: domain config search config nameserver 192.168.1.254 ..I heard it might mean something on one of the pages I was looking at. I would be very grateful for any help with this. I have tried everything I can think of and would really like to get this working this weekend so I can use it from work.

  Read the article

• How to access localhost from by ip address?

  - by Malte Werschy

  I am trying to access localhost by my ip address. My ip address is/was http://217.164.79.62/ (It is set to be automatically assigned so it keeps changing). When I enter http://localhost/ into the browser I get the xampp homepage. However when I enter http://217.164.79.62/ into my browser I get the following message: The server 217.164.79.62:80 requires a username and password. User Name: Password: How do I get the username and password?

  Read the article

• Using IP Tables to deny packet patterns?

  - by Chris

  I'm not experienced with IP tables but it's something I'll be looking into if this is plausible. I'm looking to set up a system to inspect packets and look for a pattern similar to korek's chop chop attack. Is there a way to set up the IP tables to defend against this attack? Thanks

  Read the article

• Redirecting access from a domain name to IP:port

  - by hexacyanide

  Right now I have a server running on IP:Port. If I wanted to use DNS but redirect to the port, how would I do so? I've heard that it's possible, but how would I do so, even if it includes creating something such as a proxy? For example, visiting: domain.tld would instead access IP:Port and the port could be anything I wanted it to be. If no direct solution exist, how would I go along using a "VirtualHost"?

  Read the article

• when ping for two diffrent ip address one after other one of it always fails

  - by Mukesh

  when ping for two different ip address say 202.177.251.xxx and 59.183.5.yyy one after other one of it always fails. say if i ping one ip address it does not receive packet back and then i ping second one in a loop it receives the packet back though both are connected.

  Read the article

• IP address times out

  - by Werner

  I'm running a dedicated server with a couple of game servers running on 4 different IP addresses. The most network-heavy server times out a few times during peak hours and all other communication (FTP/SSH) through the same IP also briefly times out. Other servers using other IPs are fine and unaffected as well as FTP/SSH using other IPs. The server is running Debian 6. What causes this, and is there anything I can do?

  Read the article

• Godaddy : linking domain name to IP address

  - by Lokpere

  I just bought a domain name for my web site from GoDaddy. the content of the site is available at a public IP address. how do I link my domain name to the IP address ? how do I make it so that when someone types in my domain name, the content of the web server is displayed ? thanks.

  Read the article

• Find if IP Address is in use

  - by WedTM

  I'm trying to find if an IP address is in use. I don't want to rely on ping, as most of our hosts have ICMP echo and reply turned off. I'm looking for something that mimics window's "IP Address Conflict" detection. (How does this mechanism do it?)

  Read the article

• Fix static ip address problems in Ubuntu 10.04

  - by jane

  I used Network Manager in Ubuntu 10.04 to set a static ip address and assigned one that was already in use. Now my computer will not boot (nfs crashes). I booted from a live cd to change the configuration on the file system in /etc/network/interfaces but the file looks to be the default. Where does the network manager (the gui from system- preferences) store it's configuration so I can overwrite it and enter the correct ip addresss and have a happy working computer again. thanks!!

  Read the article

• need direction with assigning 2 ip addresses from my isp for gaming and web hosting

  - by user269451

  Hello and thank you for the help in advance. I have a Windows server 2003 that I want to use to host my companies website and a game server for MineCraft. I have a few weblinks bookmarked in regards to setting up the web and game server but no idea what I do with the two static ip's. Do I assign each network adapter the static ip's or do they go on the router? Any help and direction is greatly appreciated.

  Read the article

• IP not detected in terremark enteprise cloud server - how to install VMware on instance?

  - by JohnMerlino

  Using terremark enteprise cloud, when you create a server, you assigned an IP address to them and that IP is visible under Detected IP when selecting the server. However, I created a server, with IP address and I created an internet service and connected it with a node. I used protocol TCP and mapped it to port 3001. But I notice when I select my server, the IP address doesnt dsplay under Detected IP and then I VPN Connect, launch terminal and try to SSH with the IP to my server, and I get connection timed out. I presume the reason lies in that the IP address is not being detected. Someone suggested that my VMware-Tools is out of date and in fact on the server instance for VMware-Tools it does say "out of date". I'm not sure how to mount the instance and install VMware-Tools. I am using Mac OSX. Someone said that it will only work on PC running IE.

  Read the article

• C++ Linux getpeername IP family

  - by gln

  hi In my Linux C++ application I'm using getpeername in order to get the peer IP. my problem is: when I enable the IPv6 on my machine the IP I got from the peer is with family IF_INET6 although it is IPv4. code: int GetSockPeerIP( int sock) { struct sockaddr_storage ss; struct socklen_t salen = sizeof(ss); struct sockaddr *sa; memset(&ss,0,salen); sa = (sockaddr *)&ss; if(getpeername(sock,sa,&salen) != 0) { return -1; } char * ip=NULL: if(sa->sa_family == AF_INET) { ip = inet_ntoa((struct sockaddr_in *)sa)->sin_addr); } else { //ip = how to convert IPv6 to char IP? } return 0; } how can I fix it? thanks1

  Read the article

• How to Quickly Add Multiple IP Addresses to Windows Servers

  - by Sysadmin Geek

  If you have ever added multiple IP addresses to a single Windows server, going through the graphical interface is an incredible pain as each IP must be added manually, each in a new dialog box. Here’s a simple solution. Needless to say, this can be incredibly monotonous and time consuming if you are adding more than a few IP addresses. Thankfully, there is a much easier way which allows you to add an entire subnet (or more) in seconds. Adding an IP Address from the Command Line Windows includes the “netsh” command which allows you to configure just about any aspect of your network connections. If you view the accepted parameters using “netsh /?” you will be presented with a list of commands each which have their own list of commands (and so on). For the purpose of adding IP addresses, we are interested in this string of parameters: netsh interface ipv4 add address Note: For Windows Server 2003/XP and earlier, “ipv4″ should be replaced with just “ip” in the netsh command. If you view the help information, you can see the full list of accepted parameters but for the most part what you will be interested in is something like this: netsh interface ipv4 add address “Local Area Connection” 192.168.1.2 255.255.255.0 The above command adds the IP Address 192.168.1.2 (with Subnet Mask 255.255.255.0) to the connection titled “Local Area Network”. Adding Multiple IP Addresses at Once When we accompany a netsh command with the FOR /L loop, we can quickly add multiple IP addresses. The syntax for the FOR /L loop looks like this: FOR /L %variable IN (start,step,end) DO command So we could easily add every IP address from an entire subnet using this command: FOR /L %A IN (0,1,255) DO netsh interface ipv4 add address “Local Area Connection” 192.168.1.%A 255.255.255.0 This command takes about 20 seconds to run, where adding the same number of IP addresses manually would take significantly longer. A Quick Demonstration Here is the initial configuration on our network adapter: ipconfig /all Now run netsh from within a FOR /L loop to add IP’s 192.168.1.10-20 to this adapter: FOR /L %A IN (10,1,20) DO netsh interface ipv4 add address “Local Area Connection” 192.168.1.%A 255.255.255.0 After the above command is run, viewing the IP Configuration of the adapter now shows: Latest Features How-To Geek ETC How To Create Your Own Custom ASCII Art from Any Image How To Process Camera Raw Without Paying for Adobe Photoshop How Do You Block Annoying Text Message (SMS) Spam? How to Use and Master the Notoriously Difficult Pen Tool in Photoshop HTG Explains: What Are the Differences Between All Those Audio Formats? How To Use Layer Masks and Vector Masks to Remove Complex Backgrounds in Photoshop Bring Summer Back to Your Desktop with the LandscapeTheme for Chrome and Iron The Prospector – Home Dash Extension Creates a Whole New Browsing Experience in Firefox KinEmote Links Kinect to Windows Why Nobody Reads Web Site Privacy Policies [Infographic] Asian Temple in the Snow Wallpaper 10 Weird Gaming Records from the Guinness Book

  Read the article

• Whitelist IP from google-authenticator in sshd pam

  - by spudwaffle

  My Ubuntu 12.04 server uses the google-authenticator pam module to provide two step authentication for ssh. I need to make it so that a certain IP does not need to type the verification code. The /etc/pam.d/sshd file is below: # PAM configuration for the Secure Shell service # Read environment variables from /etc/environment and # /etc/security/pam_env.conf. auth required pam_env.so # [1] # In Debian 4.0 (etch), locale-related environment variables were moved to # /etc/default/locale, so read that as well. auth required pam_env.so envfile=/etc/default/locale # Standard Un*x authentication. @include common-auth # Disallow non-root logins when /etc/nologin exists. account required pam_nologin.so # Uncomment and edit /etc/security/access.conf if you need to set complex # access limits that are hard to express in sshd_config. # account required pam_access.so # Standard Un*x authorization. @include common-account # Standard Un*x session setup and teardown. @include common-session # Print the message of the day upon successful login. session optional pam_motd.so # [1] # Print the status of the user's mailbox upon successful login. session optional pam_mail.so standard noenv # [1] # Set up user limits from /etc/security/limits.conf. session required pam_limits.so # Set up SELinux capabilities (need modified pam) # session required pam_selinux.so multiple # Standard Un*x password updating. @include common-password auth required pam_google_authenticator.so I've already tried adding a auth sufficient pam_exec.so /etc/pam.d/ip.sh line above the google-authenticator line, but I can't understand how to check an IP adress in the bash script.

  Read the article

• Difference between accessing a website using Local host and IP address

  - by Cdeez

  I have developed an ASP.NET website and deployed into my IIS server. Now to see that my IIS is installed fine, I type local host in my address bar, and I get the welcome screen of IIS and its documentation in a separate window. Now I gave the url of my website http://localhost/mysites/site2/Default.aspx I access my site. Also giving my IP address instead of local host like: http://192.168.1.46/mysites/site2/Default.aspx also works. Just out of curiosity I wanted to see what happens when I give my IP address in addressbar. It asks me a user name and password saying:The server 192.168.1.46:80 requires a user name and password. I donot know what user name and password it is asking, and as of my knowledge I thought localhost points to my own IP address internally. But what is the difference and also what username and password do I need for it? Update: On chrome and IE just giving localhost displays the welcome screen, but on mozilla, localhost is also asking for a username and password.

  Read the article

• IP address from a MAC address

  - by acermate433s

  I'm writing a class to integrate a POS card reader device to our software. In order for it to work I must know what IP it's using. We were given some sample code by the service provider and the way they do this is they open a website (http://www.ebizchargeemv.com/getip.php?mac={MAC address of device}) and it would return the IP address of the device. The device I'm using is a POSLynx220 Mini. It has an ethernet port that connects to the internet to communicate with the service provider. I send TCP data to it and the device then controls a PIN pad that prompts a client to swipe his card. It's probably a mini computer that communicates with the service provider and uses the PIN pad as its input device. Just being curious but how did they implement this? Are they implementing it using ARP? I'm planning on not using their website to determine the IP of the device. I've seen some code that uses ARP but using executing ARP in one of the PC didn't detect the POS device.

  Read the article

• Is this a solution for having multiple SSL certificates on the same IP

  - by Saif Bechan

  I am running CentOS running on a VPS. I read some guides on having multiple SSL certificates on the same system, but I can not get the basics to work. The guide I got that makes the most sense to me is the doing the following. In CentOS I can make virtual NIC's. So I made 2 virtual NIC's to start with. 192.168.10.1, 192.168.10.2. Now I work in ISP manager Pro, so this is listening on my primary ip 1.1.1.1 For each website I have them listening on 192.168.10.1:80, 192.168.10.1:443 In the hosts file I made the following 2 entries 192.168.10.1 1st.com 192.168.10.2 2nd.com Now the strange thing is that when I browser to 1st.com I do not get the website located at 192.168.10.1, I get the website located at my prim IP 1.1.1.1 Should I do something like forwarding or routing for this setup to work? And the basic question: Will this setup even work? Are the SSL certificates based on the IP adress, or are the based on the host name, 1st.com and 2nd.com.

  Read the article

• IP routing Solaris 9 access the internet from local network

  - by help_me

  I am trying to configure the NICS on the Solaris Sparc server. My problem lies in getting out to the "Internet" from the local network. I have requested the NIC to receive a DHCP server address #ifconfig -interface dhcp start. If anyone could guide me as to what I need to do next. I am not able to ping 4.2.2.2 or access the internet. Much appreciated, thank you #uname -a SunOS dev 5.9 Generic_122300-59 sun4u sparc SUNW,Sun-Fire-V210 ifconfig -a lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2 inet 10.100.0.3 netmask ffffc000 broadcast 10.100.63.255 bge0:2: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2 inet 10.100.0.22 netmask ffffc000 broadcast 10.100.63.255 bge3: flags=1004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 1500 index 12 inet 169.14.60.37 netmask fffffe00 broadcast 169.14.61.255 cat /etc/defaultrouter 10.100.0.254 169.14.60.1 cat /etc/resolv.conf nameserver 169.14.96.73 nameserver 169.10.8.4 netstat -rn Routing Table: IPv4 Destination Gateway Flags Ref Use Interface -------------------- -------------------- ----- ----- ------ --------- 169.14.60.37 169.14.60.1 UGH 1 0 169.14.60.0 169.14.60.37 U 1 18 bge3 10.100.0.0 10.100.0.3 U 1 34940 bge0 10.100.0.0 10.100.0.22 U 1 0 bge0:2 224.0.0.0 10.100.0.3 U 1 0 bge0 default 10.100.0.254 UG 1 111 default 169.14.60.1 UG 1 26 127.0.0.1 127.0.0.1 UH 10 59464 lo0 bash-2.05$ sudo ndd -get /dev/ip bge0:ip_forwarding 1 bash-2.05$ sudo ndd -get /dev/ip bge3:ip_forwarding 1 bash-2.05$ sudo ndd -get /dev/ip ip_forwarding 1

  Read the article

• Cisco 891w multiple VLAN configuration

  - by Jessica

  I'm having trouble getting my guest network up. I have VLAN 1 that contains all our network resources (servers, desktops, printers, etc). I have the wireless configured to use VLAN1 but authenticate with wpa2 enterprise. The guest network I just wanted to be open or configured with a simple WPA2 personal password on it's own VLAN2. I've looked at tons of documentation and it should be working but I can't even authenticate on the guest network! I've posted this on cisco's support forum a week ago but no one has really responded. I could really use some help. So if anyone could take a look at the configurations I posted and steer me in the right direction I would be extremely grateful. Thank you! version 15.0 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname ESI ! boot-start-marker boot-end-marker ! logging buffered 51200 warnings ! aaa new-model ! ! aaa authentication login userauthen local aaa authorization network groupauthor local ! ! ! ! ! aaa session-id common ! ! ! clock timezone EST -5 clock summer-time EDT recurring service-module wlan-ap 0 bootimage autonomous ! crypto pki trustpoint TP-self-signed-3369945891 enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-3369945891 revocation-check none rsakeypair TP-self-signed-3369945891 ! ! crypto pki certificate chain TP-self-signed-3369945891 certificate self-signed 01 (cert is here) quit ip source-route ! ! ip dhcp excluded-address 192.168.1.1 ip dhcp excluded-address 192.168.1.5 ip dhcp excluded-address 192.168.1.2 ip dhcp excluded-address 192.168.1.200 192.168.1.210 ip dhcp excluded-address 192.168.1.6 ip dhcp excluded-address 192.168.1.8 ip dhcp excluded-address 192.168.3.1 ! ip dhcp pool ccp-pool import all network 192.168.1.0 255.255.255.0 default-router 192.168.1.1 dns-server 10.171.12.5 10.171.12.37 lease 0 2 ! ip dhcp pool guest import all network 192.168.3.0 255.255.255.0 default-router 192.168.3.1 dns-server 10.171.12.5 10.171.12.37 ! ! ip cef no ip domain lookup no ipv6 cef ! ! multilink bundle-name authenticated license udi pid CISCO891W-AGN-A-K9 sn FTX153085WL ! ! username ESIadmin privilege 15 secret 5 $1$g1..$JSZ0qxljZAgJJIk/anDu51 username user1 password 0 pass ! ! ! class-map type inspect match-any ccp-cls-insp-traffic match protocol cuseeme match protocol dns match protocol ftp match protocol h323 match protocol https match protocol icmp match protocol imap match protocol pop3 match protocol netshow match protocol shell match protocol realmedia match protocol rtsp match protocol smtp match protocol sql-net match protocol streamworks match protocol tftp match protocol vdolive match protocol tcp match protocol udp class-map type inspect match-all ccp-insp-traffic match class-map ccp-cls-insp-traffic class-map type inspect match-any ccp-cls-icmp-access match protocol icmp class-map type inspect match-all ccp-invalid-src match access-group 100 class-map type inspect match-all ccp-icmp-access match class-map ccp-cls-icmp-access class-map type inspect match-all ccp-protocol-http match protocol http ! ! policy-map type inspect ccp-permit-icmpreply class type inspect ccp-icmp-access inspect class class-default pass policy-map type inspect ccp-inspect class type inspect ccp-invalid-src drop log class type inspect ccp-protocol-http inspect class type inspect ccp-insp-traffic inspect class class-default drop policy-map type inspect ccp-permit class class-default drop ! zone security out-zone zone security in-zone zone-pair security ccp-zp-self-out source self destination out-zone service-policy type inspect ccp-permit-icmpreply zone-pair security ccp-zp-in-out source in-zone destination out-zone service-policy type inspect ccp-inspect zone-pair security ccp-zp-out-self source out-zone destination self service-policy type inspect ccp-permit ! ! crypto isakmp policy 1 encr 3des authentication pre-share group 2 ! crypto isakmp client configuration group 3000client key 67Nif8LLmqP_ dns 10.171.12.37 10.171.12.5 pool dynpool acl 101 ! ! crypto ipsec transform-set myset esp-3des esp-sha-hmac ! crypto dynamic-map dynmap 10 set transform-set myset ! ! crypto map clientmap client authentication list userauthen crypto map clientmap isakmp authorization list groupauthor crypto map clientmap client configuration address initiate crypto map clientmap client configuration address respond crypto map clientmap 10 ipsec-isakmp dynamic dynmap ! ! ! ! ! interface FastEthernet0 ! ! interface FastEthernet1 ! ! interface FastEthernet2 ! ! interface FastEthernet3 ! ! interface FastEthernet4 ! ! interface FastEthernet5 ! ! interface FastEthernet6 ! ! interface FastEthernet7 ! ! interface FastEthernet8 ip address dhcp ip nat outside ip virtual-reassembly duplex auto speed auto ! ! interface GigabitEthernet0 description $FW_OUTSIDE$$ES_WAN$ ip address 10...* 255.255.254.0 ip nat outside ip virtual-reassembly zone-member security out-zone duplex auto speed auto crypto map clientmap ! ! interface wlan-ap0 description Service module interface to manage the embedded AP ip unnumbered Vlan1 arp timeout 0 ! ! interface Wlan-GigabitEthernet0 description Internal switch interface connecting to the embedded AP switchport trunk allowed vlan 1-3,1002-1005 switchport mode trunk ! ! interface Vlan1 description $ETH-SW-LAUNCH$$INTF-INFO-FE 1$$FW_INSIDE$ ip address 192.168.1.1 255.255.255.0 ip nat inside ip virtual-reassembly zone-member security in-zone ip tcp adjust-mss 1452 crypto map clientmap ! ! interface Vlan2 description guest ip address 192.168.3.1 255.255.255.0 ip access-group 120 in ip nat inside ip virtual-reassembly zone-member security in-zone ! ! interface Async1 no ip address encapsulation slip ! ! ip local pool dynpool 192.168.1.200 192.168.1.210 ip forward-protocol nd ip http server ip http access-class 23 ip http authentication local ip http secure-server ip http timeout-policy idle 60 life 86400 requests 10000 ! ! ip dns server ip nat inside source list 23 interface GigabitEthernet0 overload ip route 0.0.0.0 0.0.0.0 10.165.0.1 ! access-list 23 permit 192.168.1.0 0.0.0.255 access-list 100 remark CCP_ACL Category=128 access-list 100 permit ip host 255.255.255.255 any access-list 100 permit ip 127.0.0.0 0.255.255.255 any access-list 100 permit ip 10.165.0.0 0.0.1.255 any access-list 110 permit ip 192.168.0.0 0.0.5.255 any access-list 120 remark ESIGuest Restriction no cdp run ! ! ! ! ! ! control-plane ! ! alias exec dot11radio service-module wlan-ap 0 session Access point version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname ESIRouter ! no logging console enable secret 5 $1$yEH5$CxI5.9ypCBa6kXrUnSuvp1 ! aaa new-model ! ! aaa group server radius rad_eap server 192.168.1.5 auth-port 1812 acct-port 1813 ! aaa group server radius rad_acct server 192.168.1.5 auth-port 1812 acct-port 1813 ! aaa authentication login eap_methods group rad_eap aaa authentication enable default line enable aaa authorization exec default local aaa authorization commands 15 default local aaa accounting network acct_methods start-stop group rad_acct ! aaa session-id common clock timezone EST -5 clock summer-time EDT recurring ip domain name ESI ! ! dot11 syslog dot11 vlan-name one vlan 1 dot11 vlan-name two vlan 2 ! dot11 ssid one vlan 1 authentication open eap eap_methods authentication network-eap eap_methods authentication key-management wpa version 2 accounting rad_acct ! dot11 ssid two vlan 2 authentication open guest-mode ! dot11 network-map ! ! username ESIadmin privilege 15 secret 5 $1$p02C$WVHr5yKtRtQxuFxPU8NOx. ! ! bridge irb ! ! interface Dot11Radio0 no ip address no ip route-cache ! encryption vlan 1 mode ciphers aes-ccm ! broadcast-key vlan 1 change 30 ! ! ssid one ! ssid two ! antenna gain 0 station-role root ! interface Dot11Radio0.1 encapsulation dot1Q 1 native no ip route-cache bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled ! interface Dot11Radio0.2 encapsulation dot1Q 2 no ip route-cache bridge-group 2 bridge-group 2 subscriber-loop-control bridge-group 2 block-unknown-source no bridge-group 2 source-learning no bridge-group 2 unicast-flooding bridge-group 2 spanning-disabled ! interface Dot11Radio1 no ip address no ip route-cache shutdown ! encryption vlan 1 mode ciphers aes-ccm ! broadcast-key vlan 1 change 30 ! ! ssid one ! antenna gain 0 dfs band 3 block channel dfs station-role root ! interface Dot11Radio1.1 encapsulation dot1Q 1 native no ip route-cache bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled ! interface GigabitEthernet0 description the embedded AP GigabitEthernet 0 is an internal interface connecting AP with the host router no ip address no ip route-cache ! interface GigabitEthernet0.1 encapsulation dot1Q 1 native no ip route-cache bridge-group 1 no bridge-group 1 source-learning bridge-group 1 spanning-disabled ! interface GigabitEthernet0.2 encapsulation dot1Q 2 no ip route-cache bridge-group 2 no bridge-group 2 source-learning bridge-group 2 spanning-disabled ! interface BVI1 ip address 192.168.1.2 255.255.255.0 no ip route-cache ! ip http server no ip http secure-server ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag access-list 10 permit 192.168.1.0 0.0.0.255 radius-server host 192.168.1.5 auth-port 1812 acct-port 1813 key ***** bridge 1 route ip

  Read the article

• how IP ban system works

  - by Remus Rigo

  hi all Can anyone tell me how the IP ban system works. I have Dynamic IP, every time i start my PC I have a different IP. I want to know how a site (like a chat system) knows my IP and it keeps me banned... thanks

  Read the article

• Multi Domain ssl certificates - Single IP or multiple IP's

  - by erron

  I have a server with multiple IP addresses, Each address hosts a single website, Each website has a different domain name ( the company has a few divisions, each with its own branding) Will a multi domain certificate work in this case? Do multi-certs mean 1 ip with many domains? or doesn't it matter?

  Read the article

• How to Assign a Static IP Address in XP, Vista, or Windows 7

  - by Mysticgeek

  When organizing your home network it’s easier to assign each computer it’s own IP address than using DHCP. Here we will take a look at doing it in XP, Vista, and Windows 7. If you have a home network with several computes and devices, it’s a good idea to assign each of them a specific address. If you use DHCP (Dynamic Host Configuration Protocol), each computer will request and be assigned an address every time it’s booted up. When you have to do troubleshooting on your network, it’s annoying going to each machine to figure out what IP they have. Using Static IPs prevents address conflicts between devices and allows you to manage them more easily. Assigning IPs to Windows is essentially the same process, but getting to where you need to be varies between each version. Windows 7 To change the computer’s IP address in Windows 7, type network and sharing into the Search box in the Start Menu and select Network and Sharing Center when it comes up.   Then when the Network and Sharing Center opens, click on Change adapter settings. Right-click on your local adapter and select Properties. In the Local Area Connection Properties window highlight Internet Protocol Version 4 (TCP/IPv4) then click the Properties button. Now select the radio button Use the following IP address and enter in the correct IP, Subnet mask, and Default gateway that corresponds with your network setup. Then enter your Preferred and Alternate DNS server addresses. Here we’re on a home network and using a simple Class C network configuration and Google DNS. Check Validate settings upon exit so Windows can find any problems with the addresses you entered. When you’re finished click OK. Now close out of the Local Area Connections Properties window. Windows 7 will run network diagnostics and verify the connection is good. Here we had no problems with it, but if you did, you could run the network troubleshooting wizard. Now you can open the command prompt and do an ipconfig  to see the network adapter settings have been successfully changed.   Windows Vista Changing your IP from DHCP to a Static address in Vista is similar to Windows 7, but getting to the correct location is a bit different. Open the Start Menu, right-click on Network, and select Properties. The Network and Sharing Center opens…click on Manage network connections. Right-click on the network adapter you want to assign an IP address and click Properties. Highlight Internet Protocol Version 4 (TCP/IPv4) then click the Properties button. Now change the IP, Subnet mask, Default Gateway, and DNS Server Addresses. When you’re finished click OK. You’ll need to close out of Local Area Connection Properties for the settings to go into effect. Open the Command Prompt and do an ipconfig to verify the changes were successful.   Windows XP In this example we’re using XP SP3 Media Center Edition and changing the IP address of the Wireless adapter. To set a Static IP in XP right-click on My Network Places and select Properties. Right-click on the adapter you want to set the IP for and select Properties. Highlight Internet Protocol (TCP/IP) and click the Properties button. Now change the IP, Subnet mask, Default Gateway, and DNS Server Addresses. When you’re finished click OK. You will need to close out of the Network Connection Properties screen before the changes go into effect.   Again you can verify the settings by doing an ipconfig in the command prompt. In case you’re not sure how to do this, click on Start then Run.   In the Run box type in cmd and click OK. Then at the prompt type in ipconfig and hit Enter. This will show the IP address for the network adapter you changed.   If you have a small office or home network, assigning each computer a specific IP address makes it a lot easier to manage and troubleshoot network connection problems. Similar Articles Productive Geek Tips Change Ubuntu Desktop from DHCP to a Static IP AddressChange Ubuntu Server from DHCP to a Static IP AddressVista Breadcrumbs for Windows XPCreate a Shortcut or Hotkey for the Safely Remove Hardware DialogCreate a Shortcut or Hotkey to Eject the CD/DVD Drive TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips HippoRemote Pro 2.2 Xobni Plus for Outlook All My Movies 5.9 CloudBerry Online Backup 1.5 for Windows Home Server Nice Websites To Watch TV Shows Online 24 Million Sites Windows Media Player Glass Icons (icons we like) How to Forecast Weather, without Gadgets Outlook Tools, one stop tweaking for any Outlook version Zoofs, find the most popular tweeted YouTube videos

  Read the article

• How to find my VPN client IP in windows

  - by cateof

  When I run ipconfig and I get the following: C:\Documents and Settings\grmsrh14>ipconfig Windows IP Configuration Ethernet adapter Wireless Network Connection: Media State . . . . . . . . . . . : Media disconnected Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 112.25.2.222 Subnet Mask . . . . . . . . . . . : 255.255.254.0 Default Gateway . . . . . . . . . : 112.25.2.1 DHCP Class ID . . . . . . . . . . : rise Ethernet adapter Local Area Connection 2: Media State . . . . . . . . . . . : Media disconnected PPP adapter my_lab: Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 10.2.251.41 Subnet Mask . . . . . . . . . . . : 255.255.255.255 Default Gateway . . . . . . . . . : Is there a command that prints only the my_lab(VPN) IP address, ie 10.2.251.41?

  Read the article

• Impact of Changing IP Address of Outgoing IP Packets From My Network

  - by iamrohitbanga

  If I modify the source ip address of all outgoing ip packets from my network to an ip address belonging to someone else (while ensuring that the checksum is correct) then what will happen. Assume that I have a public IP address connected by a point-to-point link to an ISP. Will the ISP check that the IP address in my IP packets is correct or will it just forward the packets. I believe that ISP should just forward the packets. what mechanisms are present in the Internet that prevent this from happening?

  Read the article

• If an visitors IP address contains "google" or a similar keyword, does this mean they were a crawler?

  - by Roscoe

  Hi, I have a huge list of IP addresses recorded from various visitors to a website. A huge amount of the visitors, in some months over 70%, came from IP addresses that contained keywords such as google, yahoo, bot, crawler, etc. Does this mean that those users were infact search engine crawlers? If so, why are their so many crawlers in my visitor records in comparison to genuine human visitors? (and if not what's the explanation?) Thanks in advance.

  Read the article

< Previous Page | 8 9 10 11 12 13 14 15 16 17 18 19  | Next Page >