Search Results

Search found 304 results on 13 pages for 'logitech'.

Page 12/13 | < Previous Page | 8 9 10 11 12 13  | Next Page >

  • Static noise in headphones

    - by John Murdoch
    I have a Asus P6T based system. I was using the on-board sound (plugging in Logitech X-230 2.1 analog speakers in the green "front speakers" 3.5mm analog output, then plugging in my headphones in that). I was quite happy with the sound quality (didn't hear any static noise if volume was turned down to my normal listening level). Then about a week ago I started having terrible static noise from the left channel, and no normal audio on that left channel. Right channel had more static noise than usual but did have a bit of sound. I tried using the AC'97 in front of my case but that seemed to have no signal. I decided my on-board sound card has gone bad and bought an internal sound card to replace it (Startech 7.1Ch PCI). This fixed the "no sound from left channel problem", but I had much more audible static noise. I decided the card was low quality and/or it had interference from all the other things happening inside the computer case, and bought a Sweex SC016 external USB sound card. But even with that I have static noise in headphones. Positioning the USB sound card differently doesn't seem to help. Trying the other analog outputs (e.g., surround) doesn't help. The static noise in all cases is proportional to the volume. I have tried different headphones, but the situation is situation though perhaps the flavour of the static noise changes slightly. So what are my options? a) Get another, more expensive, external USB sound card hoping the quality will improve? b) Get another, more expensive, internal sound card (PCIe 1x perhaps) hoping the quality will improve? c) Get a dedicated DAC box? d) Get some Hi-Fi earphones? Suggestions? tl;dr - Two different sound cards both still have static noise in headphones.

    Read the article

  • Laptop accessories for mobile warrior (light power adapter & case/bag)

    - by wonsungi
    Lugging my X301 between work and home, I realized my laptop's accessories weigh more than the laptop itself! I'm ordering a 2nd AC power adapter so I don't even have to carry one at all, but I may as well get the lightest one possible. My X301 came with a pretty svelt 65W power adapter, but can anyone suggest a lighter power adapter or confirm the weights I've found below? mass vol dimensions W Model ---- ------- ----------- --- ------------------- 210g 149cm^3 108x46x30mm 65W Coolermaster [NA 65] 244g 189cm^3 140x75x18mm 65W ThermalTake [ADP65W0001] 260g 130cm^3 104x43x29mm 65W Lenovo (came with X301) 326g 198cm^3 145x76x18mm 95W Coolermaster [SNA 95] 330g 180cm^3 150x60x20mm 90W Kensington USB [K38030US] Apple's 60W power adapter seems much smaller/lighter than the PC products listed above, so I think a better PC power adapter could exist. There are much smaller 45W "netbook" adapters, but are these too weak for my X301? I would not mind if it just meant the battery couldn't charge while the laptop was on, but I am afraid there will be worse consequences. Also, I have decided to swap my Logitech Kinetik briefcase for a Tom Bihn Ristretto. Less protection, but much lighter, less bulky, and easier to carry. Any suggestions for better laptop cases/bags?

    Read the article

  • Problems with synaptic touchpad

    - by penlite
    The "enhanced" features of the synaptics touchpad (ie scroll, pinch zoom) on my windows 7 64 bit dell studio 17 only work intermittently. This was an issue with the original OEM driver and also with the new driver from synaptics - please do not suggest that i update, reinstall, install as administrator, check or jiggle the driver - if i hear that one more time i will freak out. I have researched this for days and appears to be a common problem without a solution (many suggestions to update the driver though -argh). Dell and synaptics have not been helpful. I have checked that syntpehn.exe and syntphelper.exe are running (sometimes the UAC seems to block syntpehn.exe from running at startup). When the touchpad fails i can still use it to control the pointer and access the synaptics settings although some of the options are disabled (greyed out or simply unresponsive). It is the only pointing device i have installed - i had a logitech trackball attached but have uninstalled all software and drivers (including hidden devices) as per synaptic. It is also the only device using IRQ 12. Any help would be greatly appreciated except "update the driver".

    Read the article

  • Troubleshooting a Windows 7 PC that wouldn't sleep

    - by NPE
    I have a new Windows 7 PC that wouldn't sleep (not just automatically, but also when specifically told to). The screen goes black momentarily, but within two seconds the machine comes back as if nothing has happened. I tried powercfg energy. This produces some errors quoted at the bottom of this post, plus some warnings about timer resolution. There are no USB devices connected other than wireless keyboard + mouse (Logitech MK250); I tried unplugging them to no effect. The motherboard is Asus P7P55D-E. powercfg lastwake says "Wake History Count - 0", which I take to mean that it never actually went to sleep. I dual boot into Ubuntu, and was having exactly the same problem on the Linux side. That turned out to do with USB 3.0, which I've now disabled in the BIOS. This has solved the problem on the Ubuntu side of things, but made no difference to Windows 7. Any suggestions? Suspend:USB Device not Entering Suspend The USB device did not enter the Suspend state. Processor power management may be prevented if a USB device does not enter the Suspend state when not in use. Device Name Generic USB Hub Host Controller ID PCI\VEN_8086&DEV_3B34 Host Controller Location PCI bus 0, device 29, function 0 Device ID USB\VID_8087&PID_0020 Port Path 1 USB Suspend:USB Device not Entering Suspend The USB device did not enter the Suspend state. Processor power management may be prevented if a USB device does not enter the Suspend state when not in use. Device Name USB Root Hub Host Controller ID PCI\VEN_8086&DEV_3B34 Host Controller Location PCI bus 0, device 29, function 0 Device ID USB\VID_8086&PID_3B34 Port Path USB Suspend:USB Device not Entering Suspend The USB device did not enter the Suspend state. Processor power management may be prevented if a USB device does not enter the Suspend state when not in use. Device Name USB Composite Device Host Controller ID PCI\VEN_8086&DEV_3B34 Host Controller Location PCI bus 0, device 29, function 0 Device ID USB\VID_046D&PID_C52E Port Path 1,8

    Read the article

  • Stop the constant random reboots of my GIGABYTE GA-B75M-D3V

    - by Frederic
    I've got some issues with a new system. It's rebooting constantly. The system consists of a: brand new: Gigabyte GA-B75M-D3V with F9 BIOS (latest) Intel Core i5-3470 Ivy Bridge 2x 8GB G.SKILL Ripjaws 1600MHz memory (mem-tested x-86) coming from a stable system: Creative Soundcard X-FI Titanium Asus Radeon HD4850 OCZ Vertex 3 120G SSD Sata 3 Hard disk 1TB Sata 2 ASUS Blu-ray Drive PSU 400w Connected peripherals : Toshiba tv (displayport on dvi of MB or HD4850) Wired mouse, wireless keyboard (logitech) Bluetooth usb key Azio main problem : it's not possible to read the errors from the MB. nothing on the manual neither on internet. At the beginning, I received a MB with graphic problems and the problem of rebooting. I RMA'd it. The new one doesn't have any graphic problems. but it's still constantly rebooting. I removed everything except the HD, the sound-card, the blu-ray drive and the wireless keyboard. It's still unexpectdly rebooting. I'm running a test with just the motherboard and the HD. I will update this text after the test. I've got some questions : Somebody have an idea of a test? The PSU could cause that problem? I used it a lot of years with the stable system. Update 1: BTW, if anyone has the same problem, the manual won't say it but you'll need to reset the bios between two tests (the screwdriver on the two pins) if you suspect a problem of compatibility .

    Read the article

  • Weird mouse behaviour. Debian wheezy

    - by DevNoob
    When I move my mouse slowly over the desktop the pointer jumps often a few pixels (one or two) in the opposite direction of which I move my mouse. Horribly when trying to set the cursor around some semicolons in eclipse. I guess this is the result of a wrong set resolution of it. I suppose this is because the mouse was set initially really fast and even if I do xset 1/2 3, the mouse is just to fast and unprecise for me. It aready tried to configure the xorg.conf like this: Section "InputDevice" Identifier "Configured Mouse" Driver "mouse" Option "Device" "/dev/mouse" Option "Protocol" "Auto" Option "Name" "Logitech G3" Option "Resolution" "2000" EndSection But with no effect. Maybe because there is no /dev/mouse. This ist the content of dev. Maybe you can tell me which one is the mouse. autofs block bsg btrfs-control bus cdrom cdrw char console core cpu cpu_dma_latency disk dvd dvdrw fd fd0 full fuse fw0 hidraw0 hidraw1 hpet input kmsg log loop0 loop1 loop2 loop3 loop4 loop5 loop6 loop7 loop-control MAKEDEV mapper mcelog mem net network_latency network_throughput null nvidia0 nvidiactl oldmem port ppp printer psaux ptmx pts random rfkill root rtc rtc0 sda sda1 sda2 sda3 sda5 sda6 sda7 sda8 sdb sdb1 sg0 sg1 sg2 shm snapshot snd sndstat sr0 stderr stdin stdout tty tty0 tty1 tty10 tty11 tty12 tty13 tty14 tty15 tty16 tty17 tty18 tty19 tty2 tty20 tty21 tty22 tty23 tty24 tty25 tty26 tty27 tty28 tty29 tty3 tty30 tty31 tty32 tty33 tty34 tty35 tty36 tty37 tty38 tty39 tty4 tty40 tty41 tty42 tty43 tty44 tty45 tty46 tty47 tty48 tty49 tty5 tty50 tty51 tty52 tty53 tty54 tty55 tty56 tty57 tty58 tty59 tty6 tty60 tty61 tty62 tty63 tty7 tty8 tty9 ttyS0 ttyS1 ttyS2 ttyS3 uinput urandom usb vcs vcs1 vcs2 vcs3 vcs4 vcs5 vcs6 vcs7 vcsa vcsa1 vcsa2 vcsa3 vcsa4 vcsa5 vcsa6 vcsa7 vga_arbiter vmci vmmon vmnet0 vmnet1 vmnet8 vsock watchdog xconsole zero So my question is: How do I setup my mouse correctly in Debian wheezy?

    Read the article

  • How to serve media across home network?

    - by TK Kocheran
    I'm looking to share my media across my home network. Router fully supports running a DLNA server, but I don't know if it'd be better to run the server from my main server computer instead of from the router, as the router would have to operate off of a network share and my server can operate directly off of the files. Here's what I need to serve, in order of importance: ISO 1:1 DVD rips (4-8GB files), MP4/H.264 encoded videos, MKV videos, MP3 files, JPEG/CR2 images. Maybe I'm completely ludicrous for wanting to push full DVD files across my network, but in reality, I would assume that only the parts of the actual file needed (ie: menu, main video payload for main title) would be served at any one time. Plus, encoding takes time and precious disk space, so why not stream it 1:1 ;) Does anyone know of the best way to accomplish this? Main goal is to serve it to Logitech Revue downstairs and secondary goal is to serve it to other computers in the house. For music, I assume I could run a DAAP server, but I don't think that the Revue supports that (and I can't exactly throw together an app that does it just yet).

    Read the article

  • How do you notice that the batteries of you wireless mouse are dying out?

    - by hkBattousai
    I have a Logitech M705 wireless mouse. I'm first time using a wireless mouse, so I don't have much experience with the hardware features and behavior. It is rated that it runs for 3 years with the same batteries. I think this "3 year" rating is calculated for a very low usage and activity; like 2 hours a day. I'm using it for about 12 hours a day, so I expect it to run out of batteries in a much shorter time in my case. I have been using it for about half a year. Recently (for the last two weeks), it started to make some peculiar behavior when clicking and drafging objects. - When I click something, it sometimes double click it. - When I drag something from one place to another (or selecting some text), it sometimes drops the object in the halfway (when selecting text, the text which had selected up to that time becomes unselected and it starts to select the rest of the text from that moment), but it goes on being in the "left-button-pressed" state. It is like, the pressed button switches to "unpressed" state for a moment, then returns back to the "pressed" state. When one of these faults occur, it occurs several times sequentially. There is no problem in pointer movement, scrolling or right-clicking. Since the batteries last for a very long time for this device, I don't expect it to stop working in an instance. I expect it to give these kind of syndromes of a time period. My question is; Is this how batteries run out for a wireless mouse? Or, is this another kind of hardware/software problem?

    Read the article

  • Reset sound volume in Windows 8

    - by Svish
    There seems to be a bug in Windows 8 causing the maximum volume to become lower than it really should be. I'm now at a stage where I put the volume up to max and the sound is still very low. I have a couple of Logitech Z-10 speakers with a display on them and when I touch the increase volume button on that it shows me the volume (but not able to increase it) is actually below middle even though Windows claims it to be maxed out. Is there any way I can reset the volume in Windows 8 so that I can get it up fully max again? A registry setting or something? Really don't want to have to reinstall windows or drivers or anything like that cause if it is a bug it'll probably happen again and I really don't want to have to do that every time this happens :p Any ideas? Manged to fix it by unplugging the usb connection to my speakers, turning the volume down on my computer and up on the speakers, and finally reconnecting the usb connection. Seems to have been an issue with the speakers and not Windows this time. BUT, I'm still curious how you can adjust/reset the Windows 8 sound volume without using the volume controls. Like, where is the value of the current volume setting(s) really stored? And can you manually adjust them?

    Read the article

  • InstallShield or Windows installer corrupted

    - by Bobby S
    Just recently I've been unable to install any software on my Windows 7 machine. Anything that uses InstallShield or the Windows installer will just hang or give a weird error. I noticed there will be many duplicate isbew64.exe processes (like 25) that launch and then just sit there or else a lot of msiexec.exe *32 processes, depending on what I'm trying to install. One piece of software specifically is the Logitech Harmony software. It gives me an *is_string_not_defined* error, saying c:\program files (x86)\:\ the filename, directory name, or volume label syntax is incorrect. The other thing I was trying to install was Battlefield: Bad Company 2, and that just hangs as well, and then just leaves all the Windows installer processes running in the background after I quit the install process. Very odd. I've checked well and googled these issues, it doesn't appear to be any sort of malware issue. I feel like it's related to some kind of corrupted installer application. I've rebooted, deleted the InstallShield folder in program files/common files as some places online suggested but to no avail. I have no idea what to do, any ideas?

    Read the article

  • Strange Photoshop Problem: Can not select, zoom, paint, option button 'locked'

    - by nikcub
    I have a very strange problem with Photoshop. I can not use any of the tools, since the cursor appears 'locked'. If I select v on my keyboard, it goes to the zoom tool, but the cursor does not change. If I select the paintbrush tool, I can only paint if I hold down the option key. This is what the cursor look like (I had to paint it since I couldn't capture it). It is a rectangle with two lines through it. I am running Photoshop CS4 on a Macbook Pro with Mac OS X 10.6.6. Using both the trackpad and an external Logitech MX5000 mouse I see the same issue. This started when I fired up Photoshop today for the first time in a while. I can't remember changing any options or doing anything that could cause this. Is it possible that the option key is somehow locked in place, or there is some equivalent of num lock on? Very strange problem, I would appreciate any help anybody can offer. Edit: To add, the icon remains the same within all the menu options - it never goes back to being just a normal mouse cursor. Also, right click works fine, and if I hold down option, the cursor goes back to normal and I can paint with it. I can't use Marquee, Lasso, Crop, Type etc. even with option held down. When I go into Bridge, it is the same icon.

    Read the article

  • servlet resopnse data for autocomplete

    - by shams haque
    Hello experts, Following code is in php. i want to do same in java. Please tell me how do i generate this type of array or collection in java. I need this to response to json autocomplete. <?php $q = strtolower($_GET["q"]); if (!$q) return; $items = array( "Peter Pan"=>"[email protected]", "Molly"=>"[email protected]", "Forneria Marconi"=>"[email protected]", "Master Sync"=>"[email protected]", "Dr. Tech de Log"=>"[email protected]", "Don Corleone"=>"[email protected]", "Mc Chick"=>"[email protected]", "Donnie Darko"=>"[email protected]", "Quake The Net"=>"[email protected]", "Dr. Write"=>"[email protected]" ); $result = array(); foreach ($items as $key=>$value) { if (strpos(strtolower($key), $q) !== false) { array_push($result, array( "name" => $key, "to" => $value )); } } echo json_encode($result); ?>

    Read the article

  • Accepting more simultaneous keyboard inputs

    - by unknownthreat
    Sometimes, a normal computer keyboard will only accept user's inputs up to a certain key simultaneously. I got a logitech keyboard that can accept up to 3-4 key presses at the same time. The computer does not accept any more input if you press more than 4 keys for this keyboard. And it also depends on certain areas of your keyboard as well. Some locations allow more key to be pressed (like the arrow keys), while some locations permit you to press only 1-2 keys. This also differs from keyboard to keyboard as well. Some older keyboards only accept up 1-2 keys. This isn't problematic with usual office work, but when it comes to gaming. For instance, imagine a platform game, where you have to jump, attack, and control direction at the same time. This implies several key presses and some keyboards cannot accept such simultaneous input. However, I've tried this on several games and the amount of possible keyboard inputs seem to be also different. Therefore, we have two issues: Keyboards have different amount of simultaneous inputs. Some games can accept more keyboard inputs than other games. At first, I thought this is hardware only problem, but why do some programs behave differently? Why some programs can accept more keyboard inputs than other programs? So how can we write our programs to accept more keyboard inputs?

    Read the article

  • jquery animate from object center

    - by mtwallet
    Hi. I am trying to create a product viewer similar to the one at the bottom of this page http://www.logitech.com/en-gb/. As you can see the product animates from the center rather than top left which I think is Jquery's default. So what I am doing is trying animate the width and height and then also the offset to make it look like it animates from the center. My code looks like this: <style> body { background: black; } .box { background: #fff url('pic.jpg') no-repeat 0 0; width: 200px; height: 200px; margin: 10px 4%; float: left; } </style> <script type="text/javascript"> $(document).ready(function() { $(".box").hover(function() { $(".box").not(this).fadeTo(500, 0.5); $(this).animate({ width: 300, height: 300, left: -100, top: -100 }, 500); }, function() { $(this).animate({ width: 200, height: 200, left: 100, top: 100 }, 500); $(".box").fadeTo(500, 1); }); }); </script> I cannot seem to get this working as I want. Can anyone help with this or suggest a better technique? Many thanks

    Read the article

  • Ubuntu and Belkin N150 f6d4050 Wireless USB adapter v2

    - by Andrew
    I'm new to Ubuntu, and I'm trying to get my Belkin USB adapter to work. There are plenty of discussions out there already about this, but none really helped me out. Here's what I've done - Installed ndiswrapper Installed ndisgtk Installed the driver (rt2870.inf) via ndisgtk ndisgtk reported that the driver was installed and the hardware was present. The green light on the adapter is solid green, which I assume means that Ubuntu is aware of it's presence. However, when I click the little wireless symbol at the navigation bar, there's no option to choose my adapter (assuming that it's supposed to show up there...) My adapter version is F6D4050 - Where do I go from here? I'm a Ubuntu newb, so speak slowly. :P lsusb - andrew@ubuntu:~$ lsusb Bus 002 Device 003: ID 046d:c517 Logitech, Inc. LX710 Cordless Desktop Laser Bus 002 Device 002: ID 04f9:0229 Brother Industries, Ltd Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 004: ID 050d:935b Belkin Components Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub lsmod - andrew@ubuntu:~$ lsmod Module Size Used by binfmt_misc 7960 1 fbcon 39270 71 tileblit 2487 1 fbcon font 8053 1 fbcon bitblit 5811 1 fbcon softcursor 1565 1 bitblit vga16fb 12757 0 vgastate 9857 1 vga16fb snd_cmipci 37557 2 snd_intel8x0 31155 2 snd_ac97_codec 125394 1 snd_intel8x0 ac97_bus 1450 1 snd_ac97_codec snd_mpu401 6875 0 snd_pcm_oss 41394 0 snd_mixer_oss 16299 1 snd_pcm_oss snd_pcm 87882 4 snd_cmipci,snd_intel8x0,snd_ac97_codec,snd_pcm_oss snd_opl3_lib 10846 1 snd_cmipci snd_hwdep 6924 1 snd_opl3_lib snd_mpu401_uart 6857 2 snd_cmipci,snd_mpu401 snd_seq_dummy 1782 0 snd_seq_oss 31219 0 snd_seq_midi 5829 0 snd_rawmidi 23420 2 snd_mpu401_uart,snd_seq_midi snd_seq_midi_event 7267 2 snd_seq_oss,snd_seq_midi snd_seq 57481 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event nouveau 515227 2 ttm 60847 1 nouveau snd_timer 23649 3 snd_pcm,snd_opl3_lib,snd_seq snd_seq_device 6888 6 snd_opl3_lib,snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq ns558 3704 0 ppdev 6375 0 drm_kms_helper 30742 1 nouveau joydev 11072 0 ndiswrapper 244768 0 gameport 10966 3 snd_cmipci,ns558 usblp 12407 0 asus_atk0110 10033 0 parport_pc 29958 1 serio_raw 4918 0 drm 199204 4 nouveau,ttm,drm_kms_helper i2c_algo_bit 6024 1 nouveau edac_core 45423 0 edac_mce_amd 9278 0 k8temp 3912 0 snd 71106 23 snd_cmipci,snd_intel8x0,snd_ac97_codec,snd_mpu401,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_opl3_lib,snd_hwdep,snd_mpu401_u art,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device soundcore 8052 1 snd snd_page_alloc 8500 2 snd_intel8x0,snd_pcm i2c_nforce2 6099 0 lp 9336 0 parport 37160 3 ppdev,parport_pc,lp hid_logitech 8820 0 ff_memless 5109 1 hid_logitech ohci1394 30260 0 usbhid 41084 1 hid_logitech hid 83440 2 hid_logitech,usbhid usb_storage 49833 0 skge 41049 0 ieee1394 94771 1 ohci1394 sata_sil 8895 0 forcedeth 55592 0 sata_nv 23778 1 pata_amd 11962 1 floppy 63156 0

    Read the article

  • ffmpeg video4linux2 at specified resolution

    - by wim
    When I'm trying to record a clip from my webcam, using: ffmpeg -f video4linux2 -s 640x480 -i /dev/video0 /tmp/spam.avi I get annoying problem with very low resolution video, and there is a message from ffmpeg saying: [video4linux2,v4l2 @ 0x2bff3e0] The V4L2 driver changed the video from 800x600 to 176x144 I have tried not specifying -s, or trying other sizes like 800x600, and always it forces me back to 176x144. Why is this and how can I prevent it? My webcam is one of those Logitech 9000 Pro, I know it supports better resolutions than this and I can see with v4l2-ctl --list-formats-ext that it goes up to at least 800x600. edit: complete console output follows wim@wim-desktop:~$ ffmpeg -f video4linux2 -s 640x480 -i /dev/video0 /tmp/spam.avi ffmpeg version git-2012-11-20-70c0f13 Copyright (c) 2000-2012 the FFmpeg developers built on Nov 21 2012 00:09:36 with gcc 4.6 (Ubuntu/Linaro 4.6.3-1ubuntu5) configuration: --enable-gpl --enable-libfaac --enable-libfdk-aac --enable-libmp3lame --enable-libopencore-amrnb --enable-libopencore-amrwb --enable-librtmp --enable-libtheora --enable-libvorbis --enable-libvpx --enable-x11grab --enable-libx264 --enable-nonfree --enable-version3 libavutil 52. 8.100 / 52. 8.100 libavcodec 54. 73.100 / 54. 73.100 libavformat 54. 37.100 / 54. 37.100 libavdevice 54. 3.100 / 54. 3.100 libavfilter 3. 23.101 / 3. 23.101 libswscale 2. 1.102 / 2. 1.102 libswresample 0. 17.100 / 0. 17.100 libpostproc 52. 2.100 / 52. 2.100 [video4linux2,v4l2 @ 0x37a33e0] The V4L2 driver changed the video from 640x480 to 176x144 [video4linux2,v4l2 @ 0x37a33e0] Estimating duration from bitrate, this may be inaccurate Input #0, video4linux2,v4l2, from '/dev/video0': Duration: N/A, start: 37066.740548, bitrate: 6082 kb/s Stream #0:0: Video: rawvideo (YUY2 / 0x32595559), yuyv422, 176x144, 6082 kb/s, 15 tbr, 1000k tbn, 15 tbc File '/tmp/spam.avi' already exists. Overwrite ? [y/N] y Output #0, avi, to '/tmp/spam.avi': Metadata: ISFT : Lavf54.37.100 Stream #0:0: Video: mpeg4 (FMP4 / 0x34504D46), yuv420p, 176x144, q=2-31, 200 kb/s, 15 tbn, 15 tbc Stream mapping: Stream #0:0 -> #0:0 (rawvideo -> mpeg4) Press [q] to stop, [?] for help frame= 95 fps= 22 q=2.0 Lsize= 88kB time=00:00:13.86 bitrate= 51.8kbits/s video:77kB audio:0kB subtitle:0 global headers:0kB muxing overhead 13.553706%

    Read the article

  • Gigabyte GA-Z77X-D3H MB problems

    - by Hans
    I installed a new system last week. I've some issues with it. The system consists of a: Gigabyte GA-Z77X-D3H with F9 BIOS (latest) Intel Core i5 3570K proccesor Sapphire Radeon HD7850 2x 8GB Corsair 1600MHz memory OCZ Vertex 2 120G SSD Connected peripherals : 2 Samsung 940BF (1 via DVI on GFX card, 1 via an Displayport to DVI adapter) 1 Dell U2312HM monitor (displayport) Dell USB Hub (monitor) Wired mouse, wireless keyboard (logitech) Logitch G25 wheel Canon MP800 printer Okay, my issues are the following: if I plug in 1 or more monitor at DisplayPort during boot, most of the time it won't boot properly. I get an empty message screen of UEFI: only the header GIGABYTE DUEL BIOS appears. The system reboots itself, turns on for a few seconds (no video) and then reboots again. Now it starts all over again. This repeats until I remove all displayport monitors. Windows boots, and I can use them when I replug them. The graphics card has been running fine for a few weeks on an older system (intel Q6600). Another issue is; if I plug in my G25 steering wheel, the UEFI BIOS is inaccessible. It either gives the same empty UEFI screen, or the BIOS screen is rendering but crashes half way (so pieces of text and graphics are missing, and it has crashed). If I remove the G25, all is fine. To verify the graphics card is OK and the motherboard is causing these issues, I tried an NVIDIA 8800GT graphics card. This hasn't got Displayport, but it also cannot boot the BIOS with the G25 wheel plugged in. The PC also refuses to go into or out of standby. It just hangs when going into standby, and in other occasions (when it does succesfully do so) get out of standby. Power supply is OCZ StealthXStream 600W. Proccesor is 25 - 30C idle, ~55C stressed (Scythe Mugen 2). I am really puzzled what can be done to resolve this. I am not really waiting for an RMA request (otherwise I will return the MB for another type), because it will likely mean I have to wait very long before I get a replacement. Anyone else with a similar experience on this board/chipset or can help me troubleshoot this?

    Read the article

  • Mouse Error Code 24. Windows 7

    - by Cj.
    I've had the same mouse for a while, and it's been working fine until one day, it started giving me a message about a device not working properly. I tried updating the drivers, and re-installing, I even deleted old drivers in case my computer should be a little confused. It never made a difference, and my mouse seemed to be working just fine despite getting the permanent error in my device manager, I looked it up several times online, but I never found anything I could actually use, when I go to official websites, I always get the same response "plug in so so into a different place - drivers - install silverlight before you can watch this tutorial, try it on a different machine". so I gave up on that. But now is where I have a real problem, lately, my little strange error evolved into a fullblown Error 24, and my mouse is starting to turn on and off randomely, especially when it is being used, but I do hear it go "badum..dadum" when I'm off doing something else. when I looked up error code 24, I really didn't find much other than it meaning: Code 24 This device is not present, is not working properly, or does not have all its drivers installed. (Code 24) Cause The device is installed incorrectly. The problem could be a hardware failure, or a new driver might be needed. Devices stay in this state if they have been prepared for removal. After you remove the device, this error disappears. But, I have tried uninstalling the device entirely several times, and it'll go right back to its previous state with error 24, and turning on and off randomely. what do I do? I cannot afford taking it to a repair place, I can't really afford a new mouse either, I refuse to buy cheap ones as I am a gamer, in need of more than 3 buttons, and a good grip is important. Could there possibly be some confusion in the registry? I do remember having gotten some early problems after I converted my vista to windows7. But I hardly dare going in there unless I'm 100% certain of what I'm going for, and I can honestly say I am at a loss here. Edit: it is a USB mouse we're talking about here. MX™518 Optical Gaming Mouse (logitech) Edit2: I am seeing no rupture, so it must be on the inside of my mouse, or inside the rubber, protecting the cable, that would be really inconvenient to search for

    Read the article

  • Low FPS in some games, but hardware not fully used

    - by Mario De Schaepmeester
    I just did a little funny experiment in the game/sim "Train Simulator 2013". I normally have good FPS in it (around 30) at full settings. What I did was make a really, really long train so that the calculations the sim needed to make were enormous (the sim is quite realistic, it takes all things into account like speed/acceleration, G-forces, comfort levels, possible wheel slip and many more, and most of those things on each carriage seperately). This resulted in only 14FPS as reported by the game, but it felt more like 8FPS or so. I have a Logitech G15 keyboard which has an LCD, and it allows me to monitor CPU/RAM and video card load on it. The strange thing is, all CPU cores were busy, but the total load was only about 60% maximum at all times. The video card was only on 30% load (possibly an important note, the memory was full, which is however not unusual for the game in question). The RAM had plenty of room and there weren't many operations as it didn't grow or shrink much. I just have the feeling that the game would run smoother if it used more of my hardware power. Why is it not doing so? I had the same in another game, The Elder Scrolls: Morrowind when using more than 100 mods (that all use scripting) and a few high res texture mods, + a full-on graphics improvement program. The engine is very old (2003), and so I thought this might be the cause (not being optimised for multithreading). I had thought of possible causes, like: The operating system doesn't let the games use all the resources. It doesn't make use of multi-threading appropriately. To eliminate the former, I tried a CPU stress tool and that got 100% CPU juice as I let it run, so the OS is not the problem. I gave its thread the "higher" priority though. My actual question In both games, I did things the engine was not really built to do or support. Can those games' framerate be limited cause of their own engine not being able to cope? What is the real reason and more importantly, can I help it? And in any case, could something actually be wrong with my hardware? It's all reasonably new, a couple of months, and I (almost) never experience any other trouble. Modern and much more demanding games work absolutely fine. Specs CPU: AMD Phenom II 965 X4 @ 3.4gHz RAM: 8GB of DDR3 RAM Video: MSI GTX560 (nVidia chip) with 1GB of GDDR5 memory OS: Windows 7 Ultimate 64 bit Nothing overclocked.

    Read the article

  • EHome IR receiver and Ubuntu 13 - any one have this working?

    - by squakie
    I have a "generic" USB IR receiver I purchased off of Ebay to make my life a little easier with XBMC on my Ubuntu box. I am currently running 13.10 and have never tried nor have any knowledge of IR in Ubuntu. I know of lirc, and I know a lot of it is now included in the kernel. My understanding is that lirc in basic terms maps pulses from an remote control to functions - like keyboard or mouse clicks. It is also my understanding that I might still need a driver or something for my device. lsusb shows the device as: Bus 006 Device 003: ID 147a:e016 Formosa Industrial Computing, Inc. eHome Infrared Receiver dmesg shows the following pertaining to the device: [43635.311985] usb 6-2: USB disconnect, device number 2 [43641.344387] usb 6-2: new full-speed USB device number 3 using ohci-pci [43641.543454] usb 6-2: New USB device found, idVendor=147a, idProduct=e016 [43641.543467] usb 6-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [43641.543473] usb 6-2: Product: eHome Infrared Transceiver [43641.543478] usb 6-2: Manufacturer: Formosa21 [43641.543483] usb 6-2: SerialNumber: FM000623 [43641.555736] Registered IR keymap rc-rc6-mce [43641.555968] input: Media Center Ed. eHome Infrared Remote Transceiver (147a:e016) as /devices/pci0000:00/0000:00:12.0/usb6/6-2/6-2:1.0/rc/rc2/input15 [43641.556221] rc2: Media Center Ed. eHome Infrared Remote Transceiver (147a:e016) as /devices/pci0000:00/0000:00:12.0/usb6/6-2/6-2:1.0/rc/rc2 [43641.556584] input: MCE IR Keyboard/Mouse (mceusb) as /devices/virtual/input/input16 [43641.557186] rc rc2: lirc_dev: driver ir-lirc-codec (mceusb) registered at minor = 0 [43641.731965] mceusb 6-2:1.0: Registered Formosa21 eHome Infrared Transceiver with mce emulator interface version 1 [43641.731978] mceusb 6-2:1.0: 2 tx ports (0x0 cabled) and 2 rx sensors (0x0 active) (excuse the double spacing, but I had to put in extra cr/lf using "enter" or the entire thing was just one long unreadable string). When I connect the same IR receiver to a Raspberry Pi running OpenELEC/XBMC there is no flashing led unless I press a remote button, and the device works. In Ubuntu, the led is constantly blinking, and nothing happens when I press a remote key. I tried the command line program to test but it never echoes anything back to the terminal window. I believe it must need some sort of driver or something else, but I am completely in the dark on this. If it matters I also have: - Logitech wireless keyboard/mouse USB receiver - Tenda USB wireless adapter And.....I've also noticed some errors now that show in dmesg that seem to somehow related to HDMI if that makes any sense: 46721.144731] HDMI: ELD buf size is 0, force 128 [46721.144749] HDMI: invalid ELD data byte 0 [46721.444025] HDMI: ELD buf size is 0, force 128 [46721.444061] HDMI: invalid ELD data byte 0 [46721.743375] HDMI: ELD buf size is 0, force 128 [46721.743411] HDMI: invalid ELD data byte 0 [46722.043092] HDMI: ELD buf size is 0, force 128 [46722.043118] HDMI: invalid ELD data byte 0 [46722.343086] HDMI: ELD buf size is 0, force 128 [46722.343122] HDMI: invalid ELD data byte 0 [46722.642517] HDMI: ELD buf size is 0, force 128 [46722.642574] HDMI: invalid ELD data byte 0 [46722.942459] HDMI: ELD buf size is 0, force 128 [46722.942485] HDMI: invalid ELD data byte 0 [46723.242103] HDMI: ELD buf size is 0, force 128 [46723.242129] HDMI: invalid ELD data byte 0 [46723.541877] HDMI: ELD buf size is 0, force 128 [46723.541923] HDMI: invalid ELD data byte 0 [58366.651954] HDMI: ELD buf size is 0, force 128 [58366.651980] HDMI: invalid ELD data byte 0 [58366.951523] HDMI: ELD buf size is 0, force 128 [58366.951549] HDMI: invalid ELD data byte 0 [58367.251075] HDMI: ELD buf size is 0, force 128 [58367.251121] HDMI: invalid ELD data byte 0 [58367.550517] HDMI: ELD buf size is 0, force 128 [58367.550563] HDMI: invalid ELD data byte 0 [58367.850219] HDMI: ELD buf size is 0, force 128 [58367.850256] HDMI: invalid ELD data byte 0 [58368.150160] HDMI: ELD buf size is 0, force 128 [58368.150185] HDMI: invalid ELD data byte 0 [58368.449544] HDMI: ELD buf size is 0, force 128 [58368.449570] HDMI: invalid ELD data byte 0 [58368.749583] HDMI: ELD buf size is 0, force 128 [58368.749629] HDMI: invalid ELD data byte 0 [58369.049280] HDMI: ELD buf size is 0, force 128 [58369.049326] HDMI: invalid ELD data byte 0 [58394.706273] HDMI: ELD buf size is 0, force 128 [58394.706300] HDMI: invalid ELD data byte 0 [58394.706350] HDMI: ELD buf size is 0, force 128 [58394.706367] HDMI: invalid ELD data byte 0 [58395.003032] HDMI: ELD buf size is 0, force 128 [58395.003058] HDMI: invalid ELD data byte 0 [58395.302680] HDMI: ELD buf size is 0, force 128 [58395.302705] HDMI: invalid ELD data byte 0 [58395.602442] HDMI: ELD buf size is 0, force 128 [58395.602477] HDMI: invalid ELD data byte 0 [58395.902143] HDMI: ELD buf size is 0, force 128 [58395.902179] HDMI: invalid ELD data byte 0 [58396.201839] HDMI: ELD buf size is 0, force 128 [58396.201875] HDMI: invalid ELD data byte 0 [58396.501538] HDMI: ELD buf size is 0, force 128 [58396.501574] HDMI: invalid ELD data byte 0 [58396.801232] HDMI: ELD buf size is 0, force 128 [58396.801268] HDMI: invalid ELD data byte 0 [58397.100583] HDMI: ELD buf size is 0, force 128 [58397.100627] HDMI: invalid ELD data byte 0 [63095.766042] systemd-hostnamed[8875]: Warning: nss-myhostname is not installed. Changing the local hostname might make it unresolveable. Please install nss-myhostname! dave@davepc:~$ EDIT: Maybe another way to look at this would be what does Ubuntu do or not do that OpenELEC does or doesn't do (on Raspberry Pi) such that it works in OpenELEC but not in Ubuntu?

    Read the article

  • Wireless Problem on Acer Aspire 5610z

    - by Ugur Can Yalaki
    I installed ubuntu 12.04 on my machine, but I can't get wireless connection to work. My computer is Acer Aspire 5610z. I found that some other people that have same computer, face the same problem. Here is some information about it: ****** info trace ****** * uname -a * Linux ucy-Aspire-5610Z 3.8.0-32-generic #47~precise1-Ubuntu SMP Wed Oct 2 16:22:28 UTC 2013 i686 i686 i386 GNU/Linux * lsb_release * Distributor ID: Ubuntu Description: Ubuntu 12.04.3 LTS Release: 12.04 Codename: precise * lspci * 05:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11b/g WLAN [14e4:4311] (rev 01) Subsystem: AMBIT Microsystem Corp. Device [1468:0422] Kernel driver in use: b43-pci-bridge 06:01.0 Ethernet controller [0200]: Broadcom Corporation BCM4401-B0 100Base-TX [14e4:170c] (rev 02) Subsystem: Acer Incorporated [ALI] Device [1025:0090] Kernel driver in use: b44 * lsusb * Bus 001 Device 004: ID 04e8:6863 Samsung Electronics Co., Ltd Bus 001 Device 002: ID 5986:0100 Acer, Inc Orbicam Bus 002 Device 002: ID 046d:c52f Logitech, Inc. Wireless Mouse M305 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub * PCMCIA Card Info * PRODID_1="" PRODID_2="" PRODID_3="" PRODID_4="" MANFID=0000,0000 FUNCID=255 * iwconfig * * rfkill * 0: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no * lsmod * ssb_hcd 12781 0 ssb 51554 2 ssb_hcd,b44 * nm-tool * NetworkManager Tool State: connected (global) Device: usb0 [Wired connection 2] ------------------------------------------- Type: Wired Driver: rndis_host State: connected Default: yes HW Address: Capabilities: Carrier Detect: yes Wired Properties Carrier: on IPv4 Settings: Address: 192.168.42.7 Prefix: 24 (255.255.255.0) Gateway: 192.168.42.129 DNS: 192.168.42.129 IPv6 Settings: Address: ::a05d:a1ff:fea4:1738 Prefix: 64 Gateway: fe80::504d:76ff:fe86:db04 Address: fe80::a05d:a1ff:fea4:1738 Prefix: 64 Gateway: fe80::504d:76ff:fe86:db04 DNS: fe80::504d:76ff:fe86:db04 Device: eth2 ----------------------------------------------------------------- Type: Wired Driver: b44 State: unavailable Default: no HW Address: Capabilities: Carrier Detect: yes Wired Properties Carrier: off * NetworkManager.state * [main] NetworkingEnabled=true WirelessEnabled=true WWANEnabled=true WimaxEnabled=true * NetworkManager.conf * [main] plugins=ifupdown,keyfile dns=dnsmasq [ifupdown] managed=false * interfaces * auto lo iface lo inet loopback * iwlist * * resolv.conf * nameserver 127.0.0.1 * blacklist * [/etc/modprobe.d/blacklist-ath_pci.conf] blacklist ath_pci [/etc/modprobe.d/blacklist-bcm43.conf] blacklist b43 blacklist b43legacy blacklist ssb blacklist bcm43xx blacklist brcm80211 blacklist brcmfmac blacklist brcmsmac blacklist bcma [/etc/modprobe.d/blacklist.conf] blacklist evbug blacklist usbmouse blacklist usbkbd blacklist eepro100 blacklist de4x5 blacklist eth1394 blacklist snd_intel8x0m blacklist snd_aw2 blacklist i2c_i801 blacklist prism54 blacklist bcm43xx blacklist garmin_gps blacklist asus_acpi blacklist snd_pcsp blacklist pcspkr blacklist amd76x_edac * modinfo * filename: /lib/modules/3.8.0-32-generic/kernel/drivers/usb/host/ssb-hcd.ko license: GPL description: Common USB driver for SSB Bus author: Hauke Mehrtens srcversion: E127A51EDC8F44D2C2A8F15 alias: ssb:v4243id0819rev* alias: ssb:v4243id0817rev* alias: ssb:v4243id0808rev* depends: ssb intree: Y vermagic: 3.8.0-32-generic SMP mod_unload modversions 686 filename: /lib/modules/3.8.0-32-generic/kernel/drivers/ssb/ssb.ko license: GPL description: Sonics Silicon Backplane driver srcversion: 14621F6EC014F731244437C alias: pci:v000014E4d00004350sv*sd*bc*sc*i* alias: pci:v000014E4d0000432Csv*sd*bc*sc*i* alias: pci:v000014E4d0000432Bsv*sd*bc*sc*i* alias: pci:v000014E4d00004329sv*sd*bc*sc*i* alias: pci:v000014E4d00004328sv*sd*bc*sc*i* alias: pci:v000014E4d00004325sv*sd*bc*sc*i* alias: pci:v000014E4d00004324sv*sd*bc*sc*i* alias: pci:v000014E4d0000A8D6sv*sd*bc*sc*i* alias: pci:v000014E4d00004322sv*sd*bc*sc*i* alias: pci:v000014E4d00004321sv*sd*bc*sc*i* alias: pci:v000014E4d00004320sv*sd*bc*sc*i* alias: pci:v000014E4d00004319sv*sd*bc*sc*i* alias: pci:v000014A4d00004318sv*sd*bc*sc*i* alias: pci:v000014E4d00004318sv*sd*bc*sc*i* alias: pci:v000014E4d00004315sv*sd*bc*sc*i* alias: pci:v000014E4d00004312sv*sd*bc*sc*i* alias: pci:v000014E4d00004311sv*sd*bc*sc*i* alias: pci:v000014E4d00004307sv*sd*bc*sc*i* alias: pci:v000014E4d00004306sv*sd*bc*sc*i* alias: pci:v000014E4d00004301sv*sd*bc*sc*i* depends: intree: Y vermagic: 3.8.0-32-generic SMP mod_unload modversions 686 * udev rules * PCI device 0x14e4:/sys/devices/pci0000:00/0000:00:1e.0/0000:06:01.0/ssb1:0 (b44) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0" PCI device 0x14e4:/sys/devices/pci0000:00/0000:00:1e.0/0000:06:01.0/ssb2:0 (b44) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth1" PCI device 0x14e4:/sys/devices/pci0000:00/0000:00:1e.0/0000:06:01.0/ssb3:0 (b44) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth2" * dmesg * [ 2.385241] ssb: Found chip with id 0x4311, rev 0x01 and package 0x00 [ 2.385256] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x11, vendor 0x4243) [ 2.385266] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x0A, vendor 0x4243) [ 2.385276] ssb: Core 2 found: USB 1.1 Host (cc 0x817, rev 0x03, vendor 0x4243) [ 2.385286] ssb: Core 3 found: PCI-E (cc 0x820, rev 0x01, vendor 0x4243) [ 2.448147] ssb: Sonics Silicon Backplane found on PCI device 0000:05:00.0 [ 2.468112] ssb: Found chip with id 0x4401, rev 0x02 and package 0x00 [ 2.468124] ssb: Core 0 found: Fast Ethernet (cc 0x806, rev 0x07, vendor 0x4243) [ 2.468132] ssb: Core 1 found: V90 (cc 0x807, rev 0x03, vendor 0x4243) [ 2.468140] ssb: Core 2 found: PCI (cc 0x804, rev 0x0A, vendor 0x4243) [ 2.508230] ssb: Sonics Silicon Backplane found on PCI device 0000:06:01.0 [ 2.528620] b44 ssb1:0 eth0: Broadcom 44xx/47xx 10/100 PCI ethernet driver ******** done ******** Thank you already for your help.

    Read the article

  • I, Android

    - by andrewbrust
    I’m just back from the 2011 Consumer Electronics Show (CES).  I go to CES to get a sense of what Microsoft is doing in the consumer space, and how people are reacting to it.  When I first went to CES 2 years ago, Steve Ballmer announced the beta of Windows 7 at his keynote address, and the crowd went wild.  When I went again last year, everyone was hoping for a Windows tablet announcement at the Ballmer keynote.  Although they didn’t get one (unless you count the unreleased HP Slate running Windows 7), people continued to show anticipation around Project Natal (which became Xbox 360 Kinect) and around Windows Phone 7.  On the show floor last year, there were machines everywhere running Windows 7, including lots of netbooks.  Microsoft had a serious influence at the show both years. But this year, one brand, one product, one operating system evidenced itself over and over again: Android.  Whether in the multitude of tablet devices that were shown across the show, or the burgeoning number of smartphones shown (including all four forthcoming 4G-LTE handsets at Verizon Wireless’ booth) or the Google TV set top box from Logitech and the embedded implementation in new Sony TV models, Android was was there. There was excitement in the ubiquity of Android 2.2 (Froyo) and the emergence of Android 2.3 (Gingerbread).  There was anticipation around the tablet-optimized Android 3.0 (Honeycomb).  There were highly customized skins.  There was even an official CES Android app for navigating the exhibit halls and planning events.  Android was so ubiquitous, in fact, that it became surprising to find a device that was running anything else.  It was as if Android had become the de facto Original Equipment Manufacturing (OEM) operating system. Motorola’s booth was nothing less than an Android showcase.  And it was large, and it was packed.  Clearly Moto’s fortunes have improved dramatically in the last year and change.  The fact that the company morphed from being a core Windows Mobile OEM to an Android poster child seems non-coincidental to their improved fortunes. Even erstwhile WinMo OEMs who now do produce Windows Phone 7 devices were not pushing them.  Perhaps I missed them, but I couldn’t find WP7 handsets at Samsung’s booth, nor at LG’s.  And since the only carrier exhibiting at the show was Verizon Wireless, which doesn’t yet have WP7 devices, this left Microsoft’s booth as the only place to see the phones. Why is Android so popular with consumer electronics manufacturers in Japan, South Korea, China and Taiwan?  Yes, it’s free, but there’s more to it than that.  Android seems to have succeeded as an OEM OS because it’s directed at OEMs who are permitted to personalize it and extend it, and it provides enough base usability and touch-friendliness that OEMs want it.  In the process, it has become a de facto standard (which makes OEMs want it even more), and has done so in a remarkably short time: the OS was launched on a single phone in the US just 2 1/4 years ago. Despite its success and popularity, Apple’s iOS would never be used by OEMs, because it’s not meant to be embedded and customized, but rather to provide a fully finished experience.  Ironically, Windows Phone 7 is likewise disqualified from such embedded use.  Windows Mobile (6.x and earlier) may have been a candidate had it not atrophied so much in its final 5 years of life. What can Microsoft do?  It could start by developing a true touch-centric OS for tablets, whether that be within Windows 8, or derived from Windows Phone 7.  It would then need to deconstruct that finished product into components, via a new or altered version of Windows Embedded or Windows Embedded Compact.  And if Microsoft went that far, it would only make sense to work with its OEMs and mobile carriers to make certain they showcase their products using the OS at CES, and other consumer electronics venues, prominently. Mostly though, Microsoft would need to decide if it were really committed to putting sustained time, effort and money into a commodity product, especially given the far greater financial return that it now derives from its core Windows and Office franchises. Microsoft would need to see an OEM OS for what it is: a loss leader that helps build brand and platform momentum for up-level products.  Is that enough to make the investment worthwhile?  One thing is certain: if that question is not acknowledged and answered honestly, then any investment will be squandered.

    Read the article

  • What's special about mouse capture and middle mouse button in WPF?

    - by Scott Bilas
    When I call CaptureMouse() in response to a MouseDown from the middle mouse button, it will capture and then release the mouse. Huh? I've tried using Preview events, setting Handled=true, doesn't make a difference. Am I not understanding mouse capture in WPF? Here's some minimal sample code that reproduces the problem. // TestListBox.cs using System.Diagnostics; using System.Windows.Controls; namespace Local { public class TestListBox : ListBox { public TestListBox() { MouseDown += (_, e) => { Debug.WriteLine("+MouseDown"); Debug.WriteLine(" Capture: " + CaptureMouse()); Debug.WriteLine("-MouseDown"); }; MouseUp += (_, e) => { Debug.WriteLine("+MouseUp"); ReleaseMouseCapture(); Debug.WriteLine("-MouseUp"); }; GotMouseCapture += (_, e) => Debug.WriteLine("GotMouseCapture"); LostMouseCapture += (_, e) => Debug.WriteLine("LostMouseCapture"); } } } Generating a default WPF app that has this for its main window will use the test class: <Window x:Class="Local.MainWindow" xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" xmlns:local="clr-namespace:Local" Title="MainWindow" Height="350" Width="525"> <local:TestListBox> <ListBoxItem>1</ListBoxItem> <ListBoxItem>2</ListBoxItem> <ListBoxItem>3</ListBoxItem> <ListBoxItem>4</ListBoxItem> </local:TestListBox> </Window> Upon clicking the middle button down, I get this output: +MouseDown GotMouseCapture LostMouseCapture Capture: True -MouseDown So I'm calling CaptureMouse, which in turn grabs and then releases capture, yet returns true that capture was successfully acquired. What's going on here? Is it possible that this is something with my Logitech mouse driver doing something goofy, trying to initiate 'ultrascroll' or something?

    Read the article

  • Keyboard for programming

    - by exhuma
    This may seem a bit a tangential topic. It's not directly related to actual code, but is important for our line of work nevertheless. Over the years, I've switched keyboards a few times. All of them had slightly different key layouts. And I'm not talking about the language/locale layout, but the physical layout! Why not the locale layout? Well, quite frankly, that's easy to change via software. I personally have a German keyboard but have it set to the UK layout. Why? It's quite hard to find different layouts in the shops where I live. Even ordering is not always easy in the shops. So that leaves me with Internet shops. But I prefer to "test" my keyboards before buying. The most notable changes are: Mangled "Home Key Block" I've seen this first on a Logitech keyboard, but it may have originated elsewhere. Shape of the "Enter" key I've seen three different cases so far: Two lines high, wider at the top Two lines high, wider at the bottom One line high Shape of the Backspace button I've seen two types so far: One "character" wide Two "characters" wide OS Keys For Macs, you have the Option and Command buttons, for Windows you have the Windows and Context Menu buttons. Cherry even produced a Linux keyboard once (unfortunately I cannot find many details except news results). I assume a dedicated Linux keyboard would sport a Compose key and had the SysRq always labelled as well (note that some standard layouts do this already). Obviously... .. all these differences entail that some keys have to be moved around the board a lot. Which means, if you are used to one and have to work on another one, you happen to hit the wrong keys quite often. As it happens, this is much more annoying for programmers as it is for people who write texts. Mainly because the keys which are moved around are special character keys, often used in programming. Often these hardware layouts depend also indirectly on where you buy the keyboards. Honestly, I haven't seen a keyboard with a one-line "Enter" key in Germany, nor Luxembourg. I may just have missed it but that's how it looks to me at least. A survey I've seen some attempts at surveys in the style "which keyboard is best for programming". But they all - in my opinion - are not using comparable sets. So I was wondering if it was possible to concoct a survey taking the above criteria into account. But ignoring key dimensions that one would be a bit overkill I guess ;) From what I can see there are the following types of physical layout: Backspace: 2-characters wide Enter: 2-Lines, wider top Backspace: 2-characters wide Enter: 1-Line Backspace: 1-character wide Enter: 2-Lines, wider bottom Then there are the other possible permutations (home-key block, os-keys), which in total makes for quite a large list of categories. Now, I wonder... Would anyone be interested in such a survey? I personally would. Because I am looking for the perfect fit for me. If yes, then I could really use the help of anyone here to propose some models to include in the survey. Once I have some models for each category (I'd say at least 3 per category) I could go ahead and write up a survey, put it on-line and let the it collect data for a while. What do you think?

    Read the article

  • The HTG Guide to Using a Bluetooth Keyboard with Your Android Device

    - by Matt Klein
    Android devices aren’t usually associated with physical keyboards. But, since Google is now bundling their QuickOffice app with the newly-released Kit-Kat, it appears inevitable that at least some Android tablets (particularly 10-inch models) will take on more productivity roles. In recent years, physical keyboards have been rendered obsolete by swipe style input methods such as Swype and Google Keyboard. Physical keyboards tend to make phones thick and plump, and that won’t fly today when thin (and even flexible and curved) is in vogue. So, you’ll be hard-pressed to find smartphone manufacturers launching new models with physical keyboards, thus rendering sliders to a past chapter in mobile phone evolution. It makes sense to ditch the clunky keyboard phone in favor of a lighter, thinner model. You’re going to carry around in your pocket or purse all day, why have that extra bulk and weight? That said, there is sound logic behind pairing tablets with keyboards. Microsoft continues to plod forward with its Surface models, and while critics continue to lavish praise on the iPad, its functionality is obviously enhanced and extended when you add a physical keyboard. Apple even has an entire page devoted specifically to iPad-compatible keyboards. But an Android tablet and a keyboard? Does such a thing even exist? They do actually. There are docking keyboards and keyboard/case combinations, there’s the Asus Transformer family, Logitech markets a Windows 8 keyboard that speaks “Android”, and these are just to name a few. So we know that keyboard products that are designed to work with Android exist, but what about an everyday Bluetooth keyboard you might use with Windows or OS X? How-To Geek wanted look at how viable it is to use such a keyboard with Android. We conducted some research and examined some lists of Android keyboard shortcuts. Most of what we found was long outdated. Many of the shortcuts don’t even apply anymore, while others just didn’t work. Regardless, after a little experimentation and a dash of customization, it turns out using a keyboard with Android is kind of fun, and who knows, maybe it will catch on. Setting things up Setting up a Bluetooth keyboard with Android is very easy. First, you’ll need a Bluetooth keyboard and of course an Android device, preferably running version 4.1 (Jelly Bean) or higher. For our test, we paired a second-generation Google Nexus 7 running Android 4.3 with a Samsung Series 7 keyboard. In Android, enable Bluetooth if it isn’t already on. We’d like to note that if you don’t normally use Bluetooth accessories and peripherals with your Android device (or any device really), it’s best practice to leave Bluetooth off because, like GPS, it drains the device’s battery more quickly. To enable Bluetooth, simply go to “Settings” -> “Bluetooth” and tap the slider button to “On”. To set up the keyboard, make sure it is on and then tap “Bluetooth” in the Android settings. On the resulting screen, your Android device should automatically search for and hopefully find your keyboard. If you don’t get it right the first time, simply turn the keyboard on again and then tap “Search for Devices” to try again. If it still doesn’t work, make sure you have fresh batteries and the keyboard isn’t paired to another device. If it is, you will need to unpair it before it will work with your Android device (consult your keyboard manufacturer’s documentation or Google if you don’t know how to do this). When Android finds your keyboard, select it under “Available Devices” … … and you should be prompted to type in a code: If successful, you will see that device is now “Connected” and you’re ready to go. If you want to test things out, try pressing the “Windows” key (“Apple” or “Command”) + ESC, and you will be whisked to your Home screen. So, what can you do? Traditional Mac and Windows users know there’s usually a keyboard shortcut for just about everything (and if there isn’t, there’s all kinds of ways to remap keys to do a variety of commands, tasks, and functions). So where does Android fall in terms of baked-in keyboard commands? There answer to that is kind of enough, but not too much. There are definitely established combos you can use to get around, but they aren’t clear and there doesn’t appear to be any one authority on what they are. Still, there is enough keyboard functionality in Android to make it a viable option, if only for those times when you need to get something done (long e-mail or important document) and an on-screen keyboard simply won’t do. It’s important to remember that Android is, and likely always will be a touch-first interface. That said, it does make some concessions to physical keyboards. In other words, you can get around Android fairly well without having to lift your hands off the keys, but you will still have to tap the screen regularly, unless you add a mouse. For example, you can wake your device by tapping a key rather than pressing its power button. However, if your device is slide or pattern-locked, then you’ll have to use the touchscreen to unlock it – a password or PIN however, works seamlessly with a keyboard – other things like widgets and app controls and features, have to be tapped. You get the idea. Keyboard shortcuts and navigation As we said, baked-in keyboard shortcut combos aren’t necessarily abundant nor apparent. The one thing you can always do is search. Any time you want to Google something, start typing from the Home screen and the search screen will automatically open and begin displaying results. Other than that, here is what we were able to figure out: ESC = go back CTRL + ESC = menu CTRL + ALT + DEL = restart (no questions asked) ALT + SPACE = search page (say “OK Google” to voice search) ALT + TAB (ALT + SHIFT + TAB) = switch tasks Also, if you have designated volume function keys, those will probably work too. There’s also some dedicated app shortcuts like calculator, Gmail, and a few others: CMD + A = calculator CMD + C = contacts CMD + E = e-mail CMD + G = Gmail CMD + L = Calendar CMD + P = Play Music CMD + Y = YouTube Overall, it’s not a long comprehensive list and there’s no dedicated keyboard combos for the full array of Google’s products. Granted, it’s hard to imagine getting a lot of mileage out of a keyboard with Maps but with something like Keep, you could type out long, detailed lists on your tablet, and then view them on your smartphone when you go out shopping. You can also use the arrow keys to navigate your Home screen over shortcuts and open the app drawer. When something on the screen is selected, it will be highlighted in blue. Press “Enter” to open your selection. Additionally, if an app has its own set of shortcuts, e.g. Gmail has quite a few unique shortcuts to it, as does Chrome, some – though not many – will work in Android (not for YouTube though). Also, many “universal” shortcuts such as Copy (CTRL + C), Cut (CTRL + X), Paste (CTRL + V), and Select All (CTRL + A) work where needed – such as in instant messaging, e-mail, social media apps, etc. Creating custom application shortcuts What about custom shortcuts? When we were researching this article, we were under the impression that it was possible to assign keyboard combinations to specific apps, such as you could do on older Android versions such as Gingerbread. This no long seems to be the case and nowhere in “Settings” could we find a way to assign hotkey combos to any of our favorite, oft-used apps or functions. If you do want custom keyboard shortcuts, what can you do? Luckily, there’s an app on Google Play that allows you to, among other things, create custom app shortcuts. It is called External Keyboard Helper (EKH) and while there is a free demo version, the pay version is only a few bucks. We decided to give EKH a whirl and through a little experimentation and finally reading the developer’s how-to, we found we could map custom keyboard combos to just about anything. To do this, first open the application and you’ll see the main app screen. Don’t worry about choosing a custom layout or anything like that, you want to go straight to the “Advanced settings”: In the “Advanced settings” select “Application shortcuts” to continue: You can have up to 16 custom application shortcuts. We are going to create a custom shortcut to the Facebook app. We choose “A0”, and from the resulting list, Facebook. You can do this for any number of apps, services, and settings. As you can now see, the Facebook app has now been linked to application-zero (A0): Go back to the “Advanced settings” and choose “Customize keyboard mappings”: You will be prompted to create a custom keyboard layout so we choose “Custom 1”: When you choose to create a custom layout, you can do a great many more things with your keyboard. For example, many keyboards have predefined function (Fn) keys, which you can map to your tablet’s brightness controls, toggle WiFi on/off, and much more. A word of advice, the application automatically remaps certain keys when you create a custom layout. This might mess up some existing keyboard combos. If you simply want to add some functionality to your keyboard, you can go ahead and delete EKH’s default changes and start your custom layout from scratch. To create a new combo, select “Add new key mapping”: For our new shortcut, we are going to assign the Facebook app to open when we key in “ALT + F”. To do this, we press the “F” key while in the “Scancode” field and we see it returns a value of “33”. If we wanted to use a different key, we can press “Change” and scan another key’s numerical value. We now want to assign the “ALT” key to application “A0”, previously designated as the Facebook app. In the “AltGr” field, we enter “A0” and then “Save” our custom combo. And now we see our new application shortcut. Now, as long as we’re using our custom layout, every time we press “ALT + F”, the Facebook app will launch: External Keyboard Helper extends far beyond simple application shortcuts and if you are looking for deeper keyboard customization options, you should definitely check it out. Among other things, EKH also supports dozens of languages, allows you to quickly switch between layouts using a key or combo, add up to 16 custom text shortcuts, and much more! It can be had on Google Play for $2.53 for the full version, but you can try the demo version for free. More extensive documentation on how to use the app is also available. Android? Keyboard? Sure, why not? Unlike traditional desktop operating systems, you don’t need a physical keyboard and mouse to use a mobile operating system. You can buy an iPad or Nexus 10 or Galaxy Note, and never need another accessory or peripheral – they work as intended right out of the box. It’s even possible you can write the next great American novel on one these devices, though that might require a lot of practice and patience. That said, using a keyboard with Android is kind of fun. It’s not revelatory but it does elevate the experience. You don’t even need to add customizations (though they are nice) because there are enough existing keyboard shortcuts in Android to make it usable. Plus, when it comes to inputting text such as in an editor or terminal application, we fully advocate big, physical keyboards. Bottom line, if you’re looking for a way to enhance your Android tablet, give a keyboard a chance. Do you use your Android device for productivity? Is a physical keyboard an important part of your setup? Do you have any shortcuts that we missed? Sound off in the comments and let us know what you think.     

    Read the article

< Previous Page | 8 9 10 11 12 13  | Next Page >