Search Results

Search found 4224 results on 169 pages for 'wireless'.

Page 12/169 | < Previous Page | 8 9 10 11 12 13 14 15 16 17 18 19  | Next Page >

• Ubuntu 12.04 connected to wireless network but internet not working

  - by A.J.

  I can connect to my house's wireless network just fine, but when I'm connected I can't browse the web. Firefox starts connecting to a site and then just poops out. This doesn't happen on my roommates' computers (running Windows) or on our 3DSes, so I know it's just my laptop. I already tried sudo dhclient -r sudo dhclient sudo ifconfig eth0 down sudo ifconfig eth0 up Results of a few commands I was asked to run in comments: ping -c 2 4.2.2.2 PING 4.2.2.2 (4.2.2.2) 56(84) bytes of data. ^C --- 4.2.2.2 ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1007ms ping -c 2 google.com PING google.com (173.194.33.38) 56(84) bytes of data. --- google.com ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1006ms nm-tool NetworkManager Tool State: connected (global) - Device: eth0 ----------------------------------------------------------------- Type: Wired Driver: atl1c State: unavailable Default: no HW Address: 88:AE:1D:6B:4E:E7 Capabilities: Carrier Detect: yes Speed: 100 Mb/s Wired Properties Carrier: off - Device: wlan0 [JUSTICE] ----------------------------------------------------- Type: 802.11 WiFi Driver: ath9k State: connected Default: yes HW Address: 1C:65:9D:65:C6:31 Capabilities: Speed: 1 Mb/s Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points (* = current AP) HOME-9B18: Infra, 00:26:F3:53:9B:18, Freq 2412 MHz, Rate 54 Mb/s, Strength 34 WPA WPA2 cougdad48 Network: Infra, 60:33:4B:E4:C4:5D, Freq 2437 MHz, Rate 54 Mb/s, Strength 22 WPA2 cougdad48 Guest Network: Infra, 66:33:4B:E4:C4:5D, Freq 2437 MHz, Rate 54 Mb/s, Strength 20 WPA2 belkin.ade: Infra, 94:44:52:FF:8A:DE, Freq 2457 MHz, Rate 54 Mb/s, Strength 20 WPA WPA2 *JUSTICE: Infra, 00:24:01:7B:9F:7E, Freq 2462 MHz, Rate 54 Mb/s, Strength 88 WEP CenturyLink: Infra, B2:B2:DC:8E:E2:58, Freq 2462 MHz, Rate 54 Mb/s, Strength 17 WPA WPA2 IPv4 Settings: Address: 192.168.0.11 Prefix: 24 (255.255.255.0) Gateway: 192.168.0.1 DNS: 192.168.0.1 (JUSTICE is my home's network.) ping -c 2 198.168.0.1 PING 198.168.0.1 (198.168.0.1) 56(84) bytes of data. --- 198.168.0.1 ping statistics --- 2 packets transmitted, 0 received, 100% packet loss, time 1007ms

  Read the article

• Attempting to install netgear N300 Wireless USB Adapter on Ubuntu without a present internet connection

  - by Liz

  Hello Linux/Ubuntu world out there. I don't have internet presently on the desktop I am trying to install the USB wireless adapter on. This seems to be the problem, which if the hardware would work would theoretically fix the problem. I can NOT access the internet via anything but wireless. I am presently on my laptop searching for answers while trying to install this little device. So any advice will have to take that into account. Now I have tried so far, using WINE which does not want to work, I have tried Windows Wireless Drivers which doesn't want to work, I have tried Software Sources, Other Software and it will not acknowledge the cdrom as a repository stating errors like E:Unable to stat the mount point /cdrom/ -stat (2: No such file or directory) However I can open the CD icon on my computer and access and browse the files. The computer can read the CD. I can read the CD. I've tried just plugging it in and seeing if the computer will automatically recognize the hardware, and go from there. That does not work either. I have tested USB port to just verify that the USB port works. It does. My laptop recognizes the hardware, and would easily install the software if I prompted it to. The difference is that my laptop is Vista, and I HATE Vista. Any tips, tricks?

  Read the article

• Why is wireless slow with Atheros AR9285?

  - by Luke

  I know there are many posts like this, however none of the fixes I have found have worked. I had the issue on 11.04, and after having no luck fixing it decided to try 12.04 however this has not fixed the problem. I'm using a Lenovo IdeaPad, the network card is a Atheros Communications AR9285. edit add outputs: sudo iwconfig lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"NETGEAR-PLOW" Mode:Managed Frequency:2.437 GHz Access Point: E0:91:F5:7D:1B:BA Bit Rate=65 Mb/s Tx-Power=15 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on Link Quality=66/70 Signal level=-44 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:77 Invalid misc:63 Missed beacon:0 eth0 no wireless extensions. lspci -nnk | grep -iA2 net 06:00.0 Network controller [0280]: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) [168c:002b] (rev 01) Subsystem: Lenovo Device [17aa:30a1] Kernel driver in use: ath9k -- 07:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 02) Subsystem: Lenovo Device [17aa:392e] Kernel driver in use: r8169 Thanks

  Read the article

• Help with the RT3290 Wireless adapter

  - by Potek

  I know there is a lot of questions about RT3290 wireless adapter, but I read many many of them and noone helped me with my problem. So, I have the HP Pavilion dm1 laptop and I installed Xubuntu 13.10 on it. During the instalation it poped up that I'm able to connect to the internet via network adapter. I did it obviously, but it worked for like 5 seconds, then it said that network connection is down and I couldn't connect to my router, even if i could actually see network connections avaible. Then (when installation ended) I rebooted my computer. My network was avaible! I could connect and browse the internet smoothly. Next day I turned on my laptop and I saw my wireless connection is no longer avaible, so I plugged laptop to the internet via Ethernet cable and started to explore internet searching solution for my problem. I did this: How do I get a Ralink RT3290 wireless card working? And I was able to connect BUT my kernel started to panic every time I started Mozilla or any program that is connecting to the internet. Every tip i searched was almost the same as the link above. I tried to do this many ways. I even Reinstalled Xubuntu to do everything with clear system but the same thing happened. THEN I installed Linux Mint to check whether it is a major or just Xubuntu problem. Linux Mint responded even worse, because I wasn't even able to use terminal (I clearly messed something up). I would really, really appreciate every help, because I do want to solve this problem and finally be able to use Xubuntu/Ubuntu. I'm waiting for advice from anyone patiently. If anyone wants some details, just tell me which ones.

  Read the article

• help download and install and save and use my wireless stick modem and software

  - by ADAM

  i installed Linux Ubuntu after my win os went totally dead by fatal blue screen. cannot reboot or install form CD ROM or get safe mode i installed Linux Ubuntu i still unable to install my wireless stick usb modem to connect and surf the Internet wireless form my provider. i use wireless network from neighborhood And i find it difficult to download and install and save porg and application from the INTERNET like skype and real player and others. it is different form windows and not that easy to use. i click to download for example and find real player but when click on it it opens as text file only and i cannot use it as it should be used for video and download and record from you tube. how to do it. and is there with Linux Ubuntu similar prog to download and record and save from you tube as in windows? Is there any trick to restart or reboot windows OS from the dead. can i use linux to reboot windows or to import my files from the blue screen stopped windows7? Any help is highly appreciated. thanks please email me to : [email protected]

  Read the article

• Can't connect to Wireless Network - Ubuntu 12.04 LTS & Sabrent A111N USB Dongle

  - by Ohgodwhy

  I've been trying to connect to this network for quite some time. I can't directly connect to the router with a Wire, but can access the Router with other wireless devices without any issues. I had previously tried several other Wifi nic's but none of them would load properly. Today, i went and bought a new (supported) Sabrent A111N USB Dongle, which said explicitly that it works with Linux 2.4 +. I popped the Dongle in, and low-and-behold it immediately said that there were Available Wireless Connections. I selected my connection and tried to connect, but it just loops constantly while saying Wireless Disconnected then attempts to connect again over and over. ifconfig and iwconfig both show my device in a ready and working state. However, iwlist wlan0 scan says that there are no results found. I don't get it... At one point, I could see the CPU in the DHCP client list under the router, but it doesn't fully make the connection (something about a timeout?). Any help would be appreciated. Bus 001 Device 002: ID 0bda:8176 Realtek Semiconductor Corp. RTL8188CUS 802.11n WLAN

  Read the article

• Can't install Linux drivers for ASUS N-13 wireless adapter

  - by jcc

  I have a USB N13 wireless Adapter with install CD-- For Windows. I downloaded drivers from ASUS FOR N13 for Linux. Disregard install CD that came with adapter; it's for Windows. I then downloaded Windows Wireless driver install program app from Software Center in Ubuntu 12.10. The problem is me. I am newbie with all things linux; software sources, G Debi, default archive manager, synaptic package manager and the Terminal. The downloaded driver file is a .zip file. I managed to extract it to a tar.gz file and then to open it to the contained files. When I use the Windows Wireless driver program it ends up telling me there is no .inf file and goes no further. It wants to install .inf file but I don't even see one in all the files. Can someone please help me . I think you can tell by my wording I don't have a clue. I hope this is'nt too chatty. I've tried to be explicit and to the point. Thank you. Oh, this is on an ASUS LAPTOP K53E. I've looked all over Ask Ubuntu and finally found some questions even on the N13 but they didn't help; still some differences in the exact problem.

  Read the article

• Is the BCM4306 wireless card ipv6 capable?

  - by horroricane

  I've been trying to connect with ipv6 enabled networks with my Broadcom Wireless card under Ubuntu 12.04. The wireless card model is BCM4306. $lspci $Network controller: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller (rev 03) $Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) I have been unsuccesful to connect through an ipv6 address, but I can still connect to a network when assigned an ipv4 address. While searching for an answer or a solution, I know the kernel can handle dealing with ipv6. So, what's left to question should be the hardware handling the connection. Unfortunately nothing comes up when I specifically try to search for information on BCM4306 ipv6 capabilities. I just tried using a wired connection to establish an ipv6 only connection to the network I'm on right now, but I got the same behavior of constant disconnections. Maybe it's not the hardware? I don't know.. I don't want to disable ipv6 on my machine as relevant networks I'll be connecting to will be using it exclusively, but I'm not sure what is wrong and which parts should I replace/fix to get this working.. Could someone please point me in a fruitful direction to get ipv6 working under Ubuntu 12.04?

  Read the article

• AR9485 wireless card loses ability to connect after hibernation

  - by DrewDiezel

  This has happened twice now, the first time it happened I just reinstalled Ubuntu. The only things that I've been messing with in terms of networking, have been restarting the network-manager service after I resume from hibernate (because it never works right after resume, but restarting the service fixes that), and changing my mac address with ifconfig wlan0 down && ifconfig wlan0 hw ether 11:22:33:44:55 && ifconfig wlan0 up. using tail | dmesg returns a bunch of attempts to connect, saying something like authenticating ... okay you're connected! now I'm going to just disconnect because I feel like it. (reason=3). Any ideas? If it helps maybe I'll add a picture of the tail|dmesg output later. My wireless drivers are as follows: Atheros AR9485 Wireless Network Adapter Hamachi Network Interface Microsoft Virtual Wifi Miniport Adapter Realtek PCIe GBE Family Controller VirtualBox Host-Only Ethernet Adapter Here is a pastebin of some terminal outputs that could help. Also, the reddit thread has a few answers, for anyone curious. It's located here. It is entirely possible that it's just my school wifi blocking out my laptop, and my home wifi sucks. Wifi does work at places other than my home and school, however my phone can connect to both places. Here is a pastebin of the results of the wireless-info script.

  Read the article

• Very slow wireless connection (unrelated to power management) using Netgear N150 WNA1100 in 12.04

  - by vgaldikas

  I am using a Netgear N150 WNA1100 USB Adapter. The network driver is: ath9k_htc. When I use Ubuntu 12.04 my wireless connection is much slower than when I use the WNA1100 with my Windows 7 installation on the same machine. I have been researching this and the most common reason for this seems to be related to power management. However for me this is off by default. I had entered a bunch of different commands and, at one stage, I got it to work at full power. But then I rebooted the machine and it went back to slow again. After entering the different commands I was afraid that I may have messed something up, so I performed a fresh install of Ubuntu. I still have the same problem. My wireless connection is still much slower when using Ubuntu than when using Windows 7. I am not sure what other info could help... EDIT: Ok, I have made live usb from the iso file I used to install Ubuntu on this pc, and ran it on my laptop. Still the same problem. However la[top works grand on cable. I suppose this means that my wireless adapter or network driver can be eliminated as root of the problem.. So maybe to do with router itself? I use ZyXEL P-660HW-D1

  Read the article

• Enable wireless on Dell Inspiron 1300

  - by Simon

  As per subject, I've looked at various resources and attempted ndiswrapper solutions, found a one-click solution that lead to a 404 and this but none works. I've run all updates. Once I managed to lose my wired connection as well and had to reinstall. This is my first hour with Linux. iwconfig gives this before I do anything: lo no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on eth0 no wireless extens Thanks for responding lspci returns 00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 03) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03) (prog-if 00 [VGA controller]) Subsystem: Dell Device 01c9 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at dff00000 (32-bit, non-prefetchable) [size=512K] Region 1: I/O ports at eff8 [size=8] Region 2: Memory at c0000000 (32-bit, prefetchable) [size=256M] Region 3: Memory at dfec0000 (32-bit, non-prefetchable) [size=256K] Expansion ROM at <unassigned> [disabled] Capabilities: <access denied> Kernel driver in use: i915 Kernel modules: intelfb, i915 00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03) Subsystem: Dell Device 01c9 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at dff80000 (32-bit, non-prefetchable) [size=512K] Capabilities: <access denied> 00:1b.0 Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller (rev 03) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 42 Region 0: Memory at dfebc000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 (rev 03) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=0 I/O behind bridge: 00002000-00002fff Memory behind bridge: 30000000-301fffff Prefetchable memory behind bridge: 0000000030200000-00000000303fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.3 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 4 (rev 03) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Bus: primary=00, secondary=0c, subordinate=0d, sec-latency=0 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: dfc00000-dfdfffff Prefetchable memory behind bridge: 00000000d0000000-00000000d01fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 4: I/O ports at bf80 [size=32] Kernel driver in use: uhci_hcd 00:1d.1 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 17 Region 4: I/O ports at bf60 [size=32] Kernel driver in use: uhci_hcd 00:1d.2 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 4: I/O ports at bf40 [size=32] Kernel driver in use: uhci_hcd 00:1d.3 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03) (prog-if 00 [UHCI]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 19 Region 4: I/O ports at bf20 [size=32] Kernel driver in use: uhci_hcd 00:1d.7 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03) (prog-if 20 [EHCI]) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at b0000000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d3) (prog-if 01 [Subtractive decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=02, subordinate=02, sec-latency=32 I/O behind bridge: 0000f000-00000fff Memory behind bridge: dfb00000-dfbfffff Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> 00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 03) Subsystem: Dell Device 01c9 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Kernel modules: iTCO_wdt, intel-rng 00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 03) (prog-if 8a [Master SecP PriP]) Subsystem: Dell Device 01c9 Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at bfa0 [size=16] Kernel driver in use: ata_piix 02:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02) Subsystem: Dell Device 01c9 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin A routed to IRQ 18 Region 0: Memory at dfbfc000 (32-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: b44 Kernel modules: b44 02:03.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02) Subsystem: Dell Wireless 1370 WLAN Mini-PCI Card Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin A routed to IRQ 17 Region 0: Memory at dfbfe000 (32-bit, non-prefetchable) [size=8K] Kernel driver in use: b43-pci-bridge Kernel modules: ssb and the rfkill shows 0: phy0: Wireless LAN Soft blocked: no Hard blocked: no Just checking addtional drivers. Says no additional driver installed in this system

  Read the article

• Downloads killing internet on my home network

  - by Travis

  I am currently having a problem with my wireless. Whenever I try to download anything it kills the internet for every other application(tabs within the same browser, browsers on other computers on the same network) except the process doing the download. This occurs with everything from downloading updates to iso's. I am not using a torrent. It happens when downloading upgrades, browser downloads, or anything else. This problem does not occur when I use Windows 7 on the same computer and it stops killing the internet for other computers if I turn the download/Ubuntu off. I am using an ASUS G74SX laptop running Ubuntu 12.10 with Gnome 3.6. My wireless card is an Intel Corporation Centrino Wireless-N + WiMAX 6150 (rev 67) Thanks!

  Read the article

• Lenovo v570 ubuntu 12.04 wireless hard blocked even when ext. switch is on

  - by user100987

  When I run iwconfig it say's lo and eth0 have no wireless extensions, but wlan0 it says IEEE 802.11bgn ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=off Retry long limit:7 RTS the:off Fragment the:off Power Management:off and I believe that's my problem, I just don't know how to turn it back on Any help? When I ran lspci | grep Network it gave me this 02:00.0 Network controller: Intell Corporation Centrino Wireless -N + WiMAX 6150 (rev 67) How I know that my wireless is hard blocked because when I run sudo rfkill list all I get 0: Ideapad_wlan: Wireless LAN Soft blocked: no Hard blocked: no 1: phy0: Wireless LAN Soft blocked: no Hard blocked: yes when I run lshw -c network I get. *-network DISABLED description: Wireless interface product: Centrino Wireless-N + WiMAX 6150 vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: mon1 version: 67 serial: 40:25:c2:d2:96:2c width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list logical wireless ethernet physical configuration: broadcast=yes driver=iwlwifi driverversion=3.2.0-32-generic-pae firmware=41.28.5.1 build 33926 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:43 memory:d0500000-d0501fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 06 serial: f0:de:f1:d7:a0:4d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw ip=192.168.0.65 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:2000(size=256) memory:d0404000-d0404fff memory:d0400000-d0403fff

  Read the article

• Broadband wireless drivers don't work

  - by user88235

  I have a Dell Latitude E6520 which is a Ubuntu 12.04 certified hardware. However the driver assigned to the Dell Wireless 5630 (EVDO-HSPA) Mobile Broadband Mini-Card doesn't seem to work. When I boot in Windows 7 I connect to Verizon dialing *99# with no username or password but it won't connect using Ubuntu. The windows drivers are from Novatel Wireless Inc 1.0.0.6 if that helps. This is also an internal card not USB and the hardware Id is USB\VID_413C&PID_8194&REV_0002&MI_00 If anyone can help me with obtaining the correct driver or maybe some other way of getting it to work I would be very grateful. My job requires traveling and I need internet access but hate using Win7.

  Read the article

• No Wireless Connection on a Broadcom BCM43227

  - by Nicolas

  I´ve installed Ubuntu 11.10 on my Acer Aspire Laptop and can´t get any Wireless connection. Where is my problem? My wireless card is an Acer Nplify(TM) 802.11b/g/n. Thanks in Advance @mikewhatever: nic@ubuntu:~$ lspci -nnk | grep -iA2 net Kernel driver in use: tg3 -- 02:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM57785 Gigabit Ethernet PCIe [14e4:16b5] (rev 10) Subsystem: Acer Incorporated [ALI] Device [1025:0504] Kernel driver in use: sdhci-pci 02:00.1 SD Host controller [0805]: Broadcom Corporation NetXtreme BCM57765 Memory Card Reader [14e4:16bc] (rev 10) Subsystem: Acer Incorporated [ALI] Device [1025:0504] 03:00.0 Network controller [0280]: Broadcom Corporation BCM43227 802.11b/g/n [14e4:4358] Subsystem: Foxconn International, Inc. Device [105b:e040]

  Read the article

• Wireless driver - how to load manufacturer's STA file (Ralink 3290)

  - by Matt

  Caution: I'm a newb. Hardware: Giada i35G, cedar trail atom with nvidia gf119, railtek ethernet and Ralink 3290 for wireless. Already accomplished: Installed Ubuntu 12.10, loaded GPU drivers and redirected sound out through GPU card to HDMI. Ethernet works like a charm. Issue: Can't get my wireless up and running. There seems to be no package to which I can simply run a sudo get-aspt install ... I found the corresponding Linux driver from the manufacturer's site, but I have not managed to find out what to with the file. Here's the manufacturers site: http://www.ralinktech.com/en/04_support/support.php?sn=501 I get a file with the following name: \2012_0508_RT3290_Linux_STA_v2.6.0.0.bz2 I hope somebody might be able to tell me what to do next. Thanks for reading and apologies for potentially asking a trivial question. Best regards, Matt

  Read the article

• Need Drivers for D-link DWA 525 PCI Wireless adapter

  - by Hari

  I'm using Ubuntu 12.10 32-Bit Edition. I have racently purchased D-link DWA 525 PCI Wireless Adapter. But i can't find the drivers for the adapter. I have been searching in internet for a while. Tried many options, including ndiswrapper. When i run lspci command, it detects and shows as below. 04:00.0 Network controller: Ralink corp. RT5360 Wireless 802.11n 1T/1R My kernel version is 3.5.0-18-generic. Please help me out.

  Read the article

• Wireless iwconfig rate auto too low

  - by Jamie Kitson

  Hi, left to its own devices my wireless connects at too low a speed. I have a 20meg internet connection and my wireless is slowing it down to like 3meg. When I reboot into windows it's fine. When I run iwconfig eth1 rate 24M or even 48M the connection is much faster and runs fine, why won't it automatically go higher? Is this the fault of the driver? I am running Broadcom's driver compiled from source. Would adding iwconfig eth1 rate 24M to rc.local be the right way to force it at boot? Output from iwconfig when rate=auto: eth1 IEEE 802.11 ESSID:"honeypot" Mode:Managed Frequency:2.417 GHz Access Point: xxx Bit Rate=1 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=5/5 Signal level=-47 dBm Noise level=-91 dBm Rx invalid nwid:0 Rx invalid crypt:2 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Thanks, Jamie

  Read the article

• Wireless icon shows grey box

  - by donald

  Hello I am running kubuntu 13.10. I had to install using the server disk and did a upgrade to the desktop version to enable full disk encryption using multiple drives. For some weird reason when I move my mouse over to the wireless icon which has an red circle and a line through it, up pops a grey box with nothing in it. This stops me from chosing which ssid's I can connect to. Ubuntu has the drive for my wirless card and it is working verified using #lspci | grep Network Centrino Wireless-N 2230 I am connected to my network from the install wizard but I need to be able to choose which networks. Please help.

  Read the article

• Wireless Problem on Acer Aspire 5610z

  - by Ugur Can Yalaki

  I installed ubuntu 12.04 on my machine, but I can't get wireless connection to work. My computer is Acer Aspire 5610z. I found that some other people that have same computer, face the same problem. Here is some information about it: ****** info trace ****** * uname -a * Linux ucy-Aspire-5610Z 3.8.0-32-generic #47~precise1-Ubuntu SMP Wed Oct 2 16:22:28 UTC 2013 i686 i686 i386 GNU/Linux * lsb_release * Distributor ID: Ubuntu Description: Ubuntu 12.04.3 LTS Release: 12.04 Codename: precise * lspci * 05:00.0 Network controller [0280]: Broadcom Corporation BCM4311 802.11b/g WLAN [14e4:4311] (rev 01) Subsystem: AMBIT Microsystem Corp. Device [1468:0422] Kernel driver in use: b43-pci-bridge 06:01.0 Ethernet controller [0200]: Broadcom Corporation BCM4401-B0 100Base-TX [14e4:170c] (rev 02) Subsystem: Acer Incorporated [ALI] Device [1025:0090] Kernel driver in use: b44 * lsusb * Bus 001 Device 004: ID 04e8:6863 Samsung Electronics Co., Ltd Bus 001 Device 002: ID 5986:0100 Acer, Inc Orbicam Bus 002 Device 002: ID 046d:c52f Logitech, Inc. Wireless Mouse M305 Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub * PCMCIA Card Info * PRODID_1="" PRODID_2="" PRODID_3="" PRODID_4="" MANFID=0000,0000 FUNCID=255 * iwconfig * * rfkill * 0: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no * lsmod * ssb_hcd 12781 0 ssb 51554 2 ssb_hcd,b44 * nm-tool * NetworkManager Tool State: connected (global) Device: usb0 [Wired connection 2] ------------------------------------------- Type: Wired Driver: rndis_host State: connected Default: yes HW Address: Capabilities: Carrier Detect: yes Wired Properties Carrier: on IPv4 Settings: Address: 192.168.42.7 Prefix: 24 (255.255.255.0) Gateway: 192.168.42.129 DNS: 192.168.42.129 IPv6 Settings: Address: ::a05d:a1ff:fea4:1738 Prefix: 64 Gateway: fe80::504d:76ff:fe86:db04 Address: fe80::a05d:a1ff:fea4:1738 Prefix: 64 Gateway: fe80::504d:76ff:fe86:db04 DNS: fe80::504d:76ff:fe86:db04 Device: eth2 ----------------------------------------------------------------- Type: Wired Driver: b44 State: unavailable Default: no HW Address: Capabilities: Carrier Detect: yes Wired Properties Carrier: off * NetworkManager.state * [main] NetworkingEnabled=true WirelessEnabled=true WWANEnabled=true WimaxEnabled=true * NetworkManager.conf * [main] plugins=ifupdown,keyfile dns=dnsmasq [ifupdown] managed=false * interfaces * auto lo iface lo inet loopback * iwlist * * resolv.conf * nameserver 127.0.0.1 * blacklist * [/etc/modprobe.d/blacklist-ath_pci.conf] blacklist ath_pci [/etc/modprobe.d/blacklist-bcm43.conf] blacklist b43 blacklist b43legacy blacklist ssb blacklist bcm43xx blacklist brcm80211 blacklist brcmfmac blacklist brcmsmac blacklist bcma [/etc/modprobe.d/blacklist.conf] blacklist evbug blacklist usbmouse blacklist usbkbd blacklist eepro100 blacklist de4x5 blacklist eth1394 blacklist snd_intel8x0m blacklist snd_aw2 blacklist i2c_i801 blacklist prism54 blacklist bcm43xx blacklist garmin_gps blacklist asus_acpi blacklist snd_pcsp blacklist pcspkr blacklist amd76x_edac * modinfo * filename: /lib/modules/3.8.0-32-generic/kernel/drivers/usb/host/ssb-hcd.ko license: GPL description: Common USB driver for SSB Bus author: Hauke Mehrtens srcversion: E127A51EDC8F44D2C2A8F15 alias: ssb:v4243id0819rev* alias: ssb:v4243id0817rev* alias: ssb:v4243id0808rev* depends: ssb intree: Y vermagic: 3.8.0-32-generic SMP mod_unload modversions 686 filename: /lib/modules/3.8.0-32-generic/kernel/drivers/ssb/ssb.ko license: GPL description: Sonics Silicon Backplane driver srcversion: 14621F6EC014F731244437C alias: pci:v000014E4d00004350sv*sd*bc*sc*i* alias: pci:v000014E4d0000432Csv*sd*bc*sc*i* alias: pci:v000014E4d0000432Bsv*sd*bc*sc*i* alias: pci:v000014E4d00004329sv*sd*bc*sc*i* alias: pci:v000014E4d00004328sv*sd*bc*sc*i* alias: pci:v000014E4d00004325sv*sd*bc*sc*i* alias: pci:v000014E4d00004324sv*sd*bc*sc*i* alias: pci:v000014E4d0000A8D6sv*sd*bc*sc*i* alias: pci:v000014E4d00004322sv*sd*bc*sc*i* alias: pci:v000014E4d00004321sv*sd*bc*sc*i* alias: pci:v000014E4d00004320sv*sd*bc*sc*i* alias: pci:v000014E4d00004319sv*sd*bc*sc*i* alias: pci:v000014A4d00004318sv*sd*bc*sc*i* alias: pci:v000014E4d00004318sv*sd*bc*sc*i* alias: pci:v000014E4d00004315sv*sd*bc*sc*i* alias: pci:v000014E4d00004312sv*sd*bc*sc*i* alias: pci:v000014E4d00004311sv*sd*bc*sc*i* alias: pci:v000014E4d00004307sv*sd*bc*sc*i* alias: pci:v000014E4d00004306sv*sd*bc*sc*i* alias: pci:v000014E4d00004301sv*sd*bc*sc*i* depends: intree: Y vermagic: 3.8.0-32-generic SMP mod_unload modversions 686 * udev rules * PCI device 0x14e4:/sys/devices/pci0000:00/0000:00:1e.0/0000:06:01.0/ssb1:0 (b44) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0" PCI device 0x14e4:/sys/devices/pci0000:00/0000:00:1e.0/0000:06:01.0/ssb2:0 (b44) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth1" PCI device 0x14e4:/sys/devices/pci0000:00/0000:00:1e.0/0000:06:01.0/ssb3:0 (b44) SUBSYSTEM=="net", ACTION=="add", DRIVERS=="?*", ATTR{address}=="", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth2" * dmesg * [ 2.385241] ssb: Found chip with id 0x4311, rev 0x01 and package 0x00 [ 2.385256] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x11, vendor 0x4243) [ 2.385266] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x0A, vendor 0x4243) [ 2.385276] ssb: Core 2 found: USB 1.1 Host (cc 0x817, rev 0x03, vendor 0x4243) [ 2.385286] ssb: Core 3 found: PCI-E (cc 0x820, rev 0x01, vendor 0x4243) [ 2.448147] ssb: Sonics Silicon Backplane found on PCI device 0000:05:00.0 [ 2.468112] ssb: Found chip with id 0x4401, rev 0x02 and package 0x00 [ 2.468124] ssb: Core 0 found: Fast Ethernet (cc 0x806, rev 0x07, vendor 0x4243) [ 2.468132] ssb: Core 1 found: V90 (cc 0x807, rev 0x03, vendor 0x4243) [ 2.468140] ssb: Core 2 found: PCI (cc 0x804, rev 0x0A, vendor 0x4243) [ 2.508230] ssb: Sonics Silicon Backplane found on PCI device 0000:06:01.0 [ 2.528620] b44 ssb1:0 eth0: Broadcom 44xx/47xx 10/100 PCI ethernet driver ******** done ******** Thank you already for your help.

  Read the article

• Can't connect to Wireless Access Point after installing proprietary drivers

  - by user6554

  I had Windows Vista Basic installed on my computer and I replaced it with Ubuntu 10.10. I then preceded to do the following: I downloaded the wireless driver from 'additional drivers' I enabled my wireless card And now it won't connect to my router but my game systems will. Then I downloaded WiFi-Radar  which did not seem to fix the problem. I still cannot connect to the Internet. I have done an exhaustive search of the Internet and turned up nothing.

  Read the article

• Wireless Problem on HP Pavillion G6

  - by user47954

  I have a broadcom wireless card in my laptop and the wireless is not working correctly. right in front of the router the wireless signal is 70% and across the room it barely works and in another room it disconnects. i have the drivers and everything. i am running ubuntu 11.10 64bit.it works perfectly in windows 7. can anyone help! 00:00.0 Host bridge [0600]: Advanced Micro Devices [AMD] Device [1022:1705] 00:01.0 VGA compatible controller [0300]: ATI Technologies Inc Device [1002:9649] 00:01.1 Audio device [0403]: ATI Technologies Inc Device [1002:1714] Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 00:04.0 PCI bridge [0604]: Advanced Micro Devices [AMD] Device [1022:1709] Kernel driver in use: pcieport Kernel modules: shpchp 00:11.0 SATA controller [0106]: Advanced Micro Devices [AMD] Device [1022:7804] Kernel driver in use: ahci Kernel modules: ahci 00:12.0 USB Controller [0c03]: Advanced Micro Devices [AMD] Device [1022:7807] (rev 11) Kernel driver in use: ohci_hcd 00:12.2 USB Controller [0c03]: Advanced Micro Devices [AMD] Device [1022:7808] (rev 11) Kernel driver in use: ehci_hcd 00:13.0 USB Controller [0c03]: Advanced Micro Devices [AMD] Device [1022:7807] (rev 11) Kernel driver in use: ohci_hcd 00:13.2 USB Controller [0c03]: Advanced Micro Devices [AMD] Device [1022:7808] (rev 11) Kernel driver in use: ehci_hcd 00:14.0 SMBus [0c05]: Advanced Micro Devices [AMD] Device [1022:780b] (rev 13) Kernel modules: i2c-piix4 00:14.2 Audio device [0403]: Advanced Micro Devices [AMD] Device [1022:780d] (rev 01) Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 00:14.3 ISA bridge [0601]: Advanced Micro Devices [AMD] Device [1022:780e] (rev 11) 00:14.4 PCI bridge [0604]: Advanced Micro Devices [AMD] Device [1022:780f] (rev 40) 00:15.0 PCI bridge [0604]: Advanced Micro Devices [AMD] Device [1022:43a0] Kernel driver in use: pcieport Kernel modules: shpchp 00:15.1 PCI bridge [0604]: Advanced Micro Devices [AMD] Device [1022:43a1] Kernel driver in use: pcieport Kernel modules: shpchp 00:15.2 PCI bridge [0604]: Advanced Micro Devices [AMD] Device [1022:43a2] Kernel driver in use: pcieport Kernel modules: shpchp 00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] Device [1022:1700] (rev 43) 00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] Device [1022:1701] 00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] Device [1022:1702] 00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] Device [1022:1703] 00:18.4 Host bridge [0600]: Advanced Micro Devices [AMD] Device [1022:1704] 00:18.5 Host bridge [0600]: Advanced Micro Devices [AMD] Device [1022:1718] 00:18.6 Host bridge [0600]: Advanced Micro Devices [AMD] Device [1022:1716] 00:18.7 Host bridge [0600]: Advanced Micro Devices [AMD] Device [1022:1719] 01:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) Kernel driver in use: r8169 Kernel modules: r8169 07:00.0 Network controller [0280]: Broadcom Corporation Device [14e4:4727] (rev 01) Kernel driver in use: wl Kernel modules: wl 08:00.0 Class [ff00]: Realtek Semiconductor Co., Ltd. Device [10ec:5209] (rev 01)

  Read the article

• Wireless not working, no driver showing in the Additional Drivers window

  - by edit lopez

  I am a new user of Ubuntu. I have a Asus Q501L laptop that came preinstalled with Windows 8, but I wanted to move from Windows and try something new, so I just decided to install Ubuntu without thinking to much about it. The problem I have is that I can't install the additional drivers. When I go to to Additional Drivers nothing appears, it just says: no proprietary drivers are in use and in small letters continues: a proprietary driver has private code that Ubuntu developers can't review and improve. security and others updates are dependent on drivers vendor.. I can't even use the wireless connection. I really don't know what to do. I tried to download the drivers from Asus, but when I tried to install them it said: an error occurred while loading the archive. Also I don't know the model of the PC wireless card. If there is something I can do to find out that please tell me. Thanks!

  Read the article

• Aser Aspire 3690 WIreless Not working, new Ubuntu user

  - by drew

  I don't know that much about Ubuntu, but I put it on an Acer Aspire 3690 Laptop (replaced Win Vista). Everything seems to work fine, but the wireless connection. It says "FIRMWARE MISSING". It detects that I have a wireless card, so I don't know what to do. I've already used the "ADDITIONAL DRIVERS" thing, and that didn't work. I've googled and have not found anything helpful. I don't really know what I'm doing, so can your directions please be kindergarden level? Thank you very much for any help you can provide. I really appreciate it.

  Read the article

• Can't find ALL wireless networks, just my neighbours

  - by motoringeek

  Been playing with live discs since 10.10 but now have gone ahead and dual booted. I have a Acer 5742z with a Nplify 802.11b/g/n wireless connection. The install went well and drivers seem to be working. BUT, although wireless detects some local networks it doesn't find mine. I have WPA-PSK security on my modem, could this be the problem?? I don't want to change my modem settings as all my other WIFI devices are contected to it. So I need help in finding my home network. A step by step guide would be useful. I am using Windows 7 now to write this but would love it if I could use Ubuntu online. I only can when I connect an Ethernet cable. Thanks in advance.

  Read the article

< Previous Page | 8 9 10 11 12 13 14 15 16 17 18 19  | Next Page >