Search Results

Search found 4316 results on 173 pages for 'disabled'.

Page 120/173 | < Previous Page | 116 117 118 119 120 121 122 123 124 125 126 127  | Next Page >

  • swapping or trashing with vast amounts of unmapped pagecache

    - by Marco
    I'm using kubuntu jaunty (i386 32bit), kernel 2.6.28-13-generic. I've 4Gb of RAM, of which only 3317Mb are seen by the system (I guess because of the 32bit system). I'm seeing that the pagecache utilization is continually growing, up to the point that the system is unusable (after a few days). This happens also when I don't do anything (all user applications closed and the bare minimum of services enabled). If enabled, the system starts to use swap space (using it all in the end). Even if swap is disabled, disk activity becomes continuous, with the system unresponsive. For example, right now the system is working (albeit a tad slow), with only firefox and wing ide running, and I have 2Gb cached with only 45Mb mapped: $ free total used free shared buffers cached Mem: 3346388 3247328 99060 0 8416 2117980 -/+ buffers/cache: 1120932 2225456 Swap: 2144668 519448 1625220 $ cat /proc/meminfo MemTotal: 3346388 kB MemFree: 97128 kB Buffers: 7872 kB Cached: 2120224 kB SwapCached: 413860 kB Active: 2304596 kB Inactive: 865984 kB Active(anon): 2279168 kB Inactive(anon): 830236 kB Active(file): 25428 kB Inactive(file): 35748 kB Unevictable: 32 kB Mlocked: 32 kB HighTotal: 2492940 kB HighFree: 5456 kB LowTotal: 853448 kB LowFree: 91672 kB SwapTotal: 2144668 kB SwapFree: 1625244 kB Dirty: 84 kB Writeback: 0 kB AnonPages: 629304 kB Mapped: 45768 kB Slab: 45600 kB SReclaimable: 21756 kB SUnreclaim: 23844 kB PageTables: 4468 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 3817860 kB Committed_AS: 3735020 kB VmallocTotal: 122880 kB VmallocUsed: 9352 kB VmallocChunk: 66600 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 HugePages_Surp: 0 Hugepagesize: 4096 kB DirectMap4k: 16376 kB DirectMap4M: 888832 kB If I try to drop the caches, little happes: # sync ; echo 3 > /proc/sys/vm/drop_caches ; free total used free shared buffers cached Mem: 3346388 3220580 125808 0 3020 2100600 -/+ buffers/cache: 1116960 2229428 Swap: 2144668 519356 1625312 Right now I've vm.swappiness = 5, but I've tried also with 0 and 1 (without noticeable differences). I've also tried vm.vfs_cache_pressure = 50 and 150 (again, no differences). As I said the pagecache eats all memory even with swapping turned off. What is happening? How to avoid this? TIA, Marco

    Read the article

  • directory with 980MB meta data, millions of files, how to delete it? (ext3)

    - by Alexandre
    Hello, So I'm stuck with this directory: drwxrwxrwx 2 dan users 980M 2010-12-22 18:38 sessions2 The directories contents is small - just millions of tiny little files. I want to wipe it from the filesystem but have been unable to. My first try was: find sessions2 -type f -delete and find sessions2 -type f -print0 | xargs -0 rm -f but had to stop because both caused escalating memory usage. At one point it was using 65% of the system's memory. So I thought (no doubt incorrectly), that it had to do with the fact that dir_index was enabled on the system. Perhaps find was trying to read the entire index into memory? So I did this (foolishly): tune2fs -O^dir_index /dev/xxx Alright, so that should do it. Ran the find command above again and... same thing. Crazy memory usage. I hurriedly ran tune2fs -Odir_index /dev/xxx to reenable dir_index, and ran to Server Fault! 2 questions: 1) How do I get rid of this directory on my live system? I don't care how long it takes, as long as it uses little memory and little CPU. By the way, using nice find ... I was able to reduce CPU usage, so my problem right now is only memory usage. 2) I disabled dir_index for about 20 minutes. No doubt new files were written to the filesystem in the meanwhile. I reenabled dir_index. Does that mean the system will not find the files that were written before dir_index was reenabled since their filenames will be missing from the old indexes? If so and I know these new files aren't important, can I maintain the old indexes? If not, how do I rebuild the indexes? Can it be done on a live system? Thanks!

    Read the article

  • Accessing network shares on Windows7 via SonicWall VPN client

    - by Jack Lloyd
    I'm running Windows7 x64 (fully patched) and the SonicWall 4.2.6.0305 client (64-bit, claims to support Windows7). I can login to the VPN and access network resources (eg SSH to a machine that lives behind the VPN). However I cannot seem to be able to access shared filesystems. Windows is refusing to do discovery on the VPN network. I suspect part of the problem is Windows persistently considers the VPN connection to be a 'public network'. Normally, you can open the network and sharing center and modify this setting, however it does not give me a choice for the VPN. So I did the expedient thing and turned on file sharing for public networks. I also disabled the Windows firewall for good measure. Still no luck. I can access the server directly by putting \\192.168.1.240 in the taskbar, which brings up the list of shares on the server. However, trying to open any of the shares simply tells me "Windows cannot access \\192.168.1.240\share You do not have permission to access ..."; it never asks for a domain password. I also tried Windows7 native VPN functionality - it couldn't successfully connect to the VPN at all. I suspect this is because SonicWall is using some obnoxious special/undocumented authentication system; I had similar problems trying to connect on Linux with the normal IPsec tools there. What magical invocation or control panel option am I missing that will let this work? Are there any reasonable debugging strategies? I'm feeling quite frustrated at Windows tendency to not give me much useful information that might let me understand what it is trying to do and what is going wrong.

    Read the article

  • Issues with doing a P2V on Exchange 2007

    - by PokermUNKEE
    I shutdown all Exchange services on the physical box and did a convert. Everything converted fine. Server booted up no issues and I could receive email from the outside world with no issues. But I am unable to send emails internally or externally. They just sit in the Outbox. I also disabled the DHCPClient service as I didn't want the server to get an IP address from DHCP when it first came online. It came online with no IP, then I used console to assign the correct static IP address (same one on the physical server) and rebooted. I ran the Exchange Troubleshooting Agent and it gave me the following errors: The value for the '\MSExchangeIS Mailbox\Messages Queued For Submission' counter on server exchange is greater than zero (average value is 8.8) and it appears that 'MSExchangeMailSubmission' is failing to submit messages to at least one computer with the Hub Transport server role installed over the last minute. Found 1 computers with the Hub Transport server role installed in the same Active Directory site as server exchange using local Active Directory site GUID 'ce8a4367-1bf6-4825-9cac-c4e2b115c450'. Check Local Active Directory Site Hub Transport Server Role Health (Mailflow_CheckLocalBhHealth1.1.1.1.1.1.1.1) I have one Exchange server with all the roles on it. Has anyone see this before when doing a convert? Please help :(

    Read the article

  • Remote Desktop Mobile mangles barcodes coming from scanner

    - by sfonck
    We have an application here using handhelds to scan barcodes. These handhelds are actually making a remote desktop session towards a server where the application runs. Works fine. Now we have bought some new Motorola MC55's running 'Windows Mobile 6.1 Classic', and when using the application over remote desktop: it mangles the characters of the barcodes.... I already tried following things: When scanning a barcode on the MC55 itself it is displayed correctly When scanning a barcode via the remote desktop into a notepad session it is incorrect. Played with all options of the 'Remote Desktop Mobile' - no result Disabled 'autocorrect' and 'suggest words when entering text' on the input settings - no result The strange things is: a barcode which consists of only numbers gets scanned correctly the mangled characters comes through in lower case For some codes \t is mangled in between (should normally be entered after the barcode) e.g.: 'PERIN4' becomes 'ERINp4' 'MGZB' becomes 'GZB m' 'BAK664' becomes 'AK664 b' 'MAGBFA01' becomes 'AGBFmA01' '5021879949500' gets scanned correctly Final solution: Suppllier of the handhelds said the handheld was sending the characters too fast over the remote desktop connection. They changed the handheld to wait for 50ms between sending each character, which produced correct results right now. Scanning a barcode became somewhat slower but it's almost not remarkable to endusers.

    Read the article

  • Disable raid member check upon mount to mount damaged nvidia raid1 member

    - by Halfgaar
    Hi, A friend of mine destroyed his Nvidia RAID1 array somehow and in trying to fix it, he ended up with a non-working array. Because of the RAID metadata, the actual disk data was stored at an offset from the beginning. I was able to identify this offset with dd and a hexeditor and then I used losetup to create a loop device with the proper offset, so that I could mount the partition. It was then that I ran into problems, namely that mount says: "mount: unknown filesystem type 'nvidia_raid_member'". I also had this when trying to mount a Linux MD component the other day, and because I can remember that doing that in the past worked, I surmised that it may be some kind of protection. I therefore booted an old Sysrescue CD and tried it there, which worked (because of the older version of mount/libc/kernel/whatever). I still need to try to get more data, and because I don't want to keep using that SysrecueCD, I'd like to be able to mount the disk on my normal system. So, my question is: can the check for a disk being a raid member be disabled? I guess I could also zero out blocks that look like the raid block, but I'd rather not... I made an image of the disk with par2 data, so it's revertable, but still...

    Read the article

  • Adding an user to samba

    - by JustMaximumPower
    I'm trying to setup some samba shares in my home network on an Ubuntu 12.04 machine. Everything works fine for my user account (max) but I can not add any new user. Every time I try to add new user they can not use the shares. It's likely that the error is very basic to the concept of samba but please don't just tell me to read the docs. I've been trying that for about 2 weeks now. I've set up the server with my user max who can mount transfer and the share max. Than I added the user simon with sudo adduser --no-create-home --disabled-login --shell /bin/false simon because the user should not be able to ssh into the machine. I did an sudo smbpasswd -a simon and set an (samba) password for simon and added an share for simon. I also added simon to transferusers to give him access to the share transfer. But simon can't connect to transfer or simons. ---- output of testparam: ------- Load smb config files from /etc/samba/smb.conf rlimit_max: increasing rlimit_max (1024) to minimum Windows limit (16384) Processing section "[printers]" Processing section "[print$]" Processing section "[max]" Processing section "[simons]" Processing section "[transfer]" Loaded services file OK. Server role: ROLE_STANDALONE Press enter to see a dump of your service definitions [global] server string = %h server (Samba, Ubuntu) map to guest = Bad User obey pam restrictions = Yes pam password change = Yes passwd program = /usr/bin/passwd %u passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* . unix password sync = Yes syslog = 0 log file = /var/log/samba/log.%m max log size = 1000 dns proxy = No usershare allow guests = Yes panic action = /usr/share/samba/panic-action %d idmap config * : backend = tdb [printers] comment = All Printers path = /var/spool/samba create mask = 0700 printable = Yes print ok = Yes browseable = No [print$] comment = Printer Drivers path = /var/lib/samba/printers [max] comment = Privater share von Max path = /media/Main/max read only = No create mask = 0700 [simons] comment = Privater share von Simon path = /media/Main/simon read only = No create mask = 0700 [transfer] comment = Transferlaufwerk path = /media/Main/transfer read only = No create mask = 0755 ---- The files in /media/Main: ------ drwxrwxr-x 17 max max 4096 Oct 4 19:13 max/ drwx------ 5 simon max 4096 Aug 4 15:18 simon/ drwxrwxr-x 7 max transferusers 258048 Oct 1 22:55 transfer/

    Read the article

  • List of Hidden / Virtual Windows User Accounts

    - by Synetech inc.
    I’m trying to find a way to get a comprehensive list of user accounts on a Windows 7 system, including hidden ones. The User Accounts dialog (>control userpasswords2) only shows the normal user accounts, and even the Local User and Groups editor only shows normal user accounts and standard hidden/disabled ones like Administrator and Guest. The Select Users or Groups dialog has a Find Now button which which combines users and groups, but alas, it has the same contents as the LUG. I’m looking for a more comprehensive list that includes “super-hidden” / virtual user accounts like TrustedInstaller (or to be more accurate, NT Service\TrustedInstaller—notice the different “domain”). I checked HKLM\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Winlogon\SpecialAccounts\UserList, but the SpecialAccounts key does not exist. I also checked HKLM\SOFTWARE\Microsoft\Windows NT\CurrentVersion\ProfileList, and while it does have the SystemProfile, LocalService, and NetworkService accounts listed, it does not have others (like TrustedInstaller and its ilk). TrustedInstaller specifically is a little confusing because it is a user, a service, and an executable file. I am using it as an example because it is “super hidden” in that it does not seem to be listed in any sort of user list. (As an experiment, I tried searching the whole registry for “trustedinstaller” to see if I could find a place where it is listed as a user, but found none.) To be clear, what I am looking for is a list of all accounts that can be used in a user input-field such as in permissions dialogs or as a runas argument.

    Read the article

  • Dovecot install: what does this error mean?

    - by jamie
    I have postfix and dovecot installed on CentOS 6 (linode) along with MySQL. The table and user is already set up, postfix installed fine, but dovecot gives me this error in the mail log: Warning: Killed with signal 15 (by pid=9415 uid=0 code=kill) The next few lines say this: Apr 7 16:13:35 dovecot: master: Dovecot v2.0.9 starting up (core dumps disabled) Apr 7 16:13:35 dovecot: config: Warning: NOTE: You can get a new clean config file with: doveconf -n > dovecot-new.conf Apr 7 16:13:35 dovecot: config: Warning: Obsolete setting in /etc/dovecot/dovecot.conf:1: protocols=pop3s is no longer supported. to disable non-ssl pop3, use service pop3-login { inet_listener pop3 { p$ Apr 7 16:13:35 dovecot: config: Warning: Obsolete setting in /etc/dovecot/dovecot.conf:5: ssl_cert_file has been replaced by ssl_cert = <file Apr 7 16:13:35 dovecot: config: Warning: Obsolete setting in /etc/dovecot/dovecot.conf:6: ssl_key_file has been replaced by ssl_key = <file Apr 7 16:13:35 dovecot: config: Warning: Obsolete setting in /etc/dovecot/dovecot.conf:8: namespace private {} has been replaced by namespace { type=private } Apr 7 16:13:35 dovecot: config: Warning: Obsolete setting in /etc/dovecot/dovecot.conf:24: add auth_ prefix to all settings inside auth {} and remove the auth {} section completely Apr 7 16:13:35 dovecot: config: Warning: Obsolete setting in /etc/dovecot/dovecot.conf:25: auth_user has been replaced by service auth { user } I am following directions for the install on CentOS 5 with changes in the dovecot.conf file from different sources specific to CentOS 6. So the dovecot.conf file might not be correct, but there is no good source I have found yet for making dovecot install correctly. Can anyone tell me what the error above means? The terminal does not give any message as to start OK or FAIL. When I issue the service dovecot start command, it says: Starting Dovecot Imap: and nothing more.

    Read the article

  • Excel cannot access the file with IIS7&Windows Serer 2008 R2(64bit)

    - by user838204
    I have a web project(.Net4) that needs to access Excel file, but it ends up with the following error message: Error occured during file generation.Microsoft Excel cannot access the file 'D:\xx\xx\abc.xls'. There are several possible reasons: • The file name or path does not exist. (Actually it's there) • The file is being used by another program.(It cant happen) • The workbook you are trying to save has the same name as a currently open workbook. In IIS7, I use DefaultAppPool with the Identity "myservice" who's under the Group of Administrators. In the Authentication Page of my website under IIS, Anonymous Authentication was enabled and set to "Application pool identity" and ASP.NET Impersonation was disabled. After searching the solution for hours, I found the following but NONE of them work Create folder in C:\Windows\SysWOW64\config\systemprofile\Desktop. Plz refer:this Grant rights of "myservice" in Component Services. Plz refer:this One thing strange, there is nothing in the Group of IIS_IUSRS. Is that normal? Cause I remember at least two users (DefaultAppPool & Classic .Net AppPool). Plz tell me how to fix the access problem. I assume that's permission problem of IIS but I cant solve it. Thank you.

    Read the article

  • How can I resolve Oracle 11g XE connection failure straight after installation?

    - by d3vid
    I have just installed Oracle 11g XE on a Windows 7 VirtualBox VM, using all the default options. "Getting Started" fails When I click on Getting Started I get taken to http://127.0.0.1:8080/apex/f?p=4950 which fails. After some browsing I came across a suggestion to confirm the HTTP port, but I can't get this far, because I can't connect. connect system fails If I select Run SQL command line I get taken to a SQL prompt. I enter connect system and get prompted for a password. I enter the password. I immediately get the following error: ERROR: ORA-01033: ORACLE initialization or shutdown in progress Process ID: 0 Session ID: 0 Serial number: 0 Info: Start database This happens whether or not I run Start database first. (Start database just opens a Windows command prompt window.) Info: Windows services My Oracle services start as follows: Starting the manual services doesn't resolve the problem. Enabling and starting the disabled service doesn't resolve the problem. Is there something I haven't done? How can I resolve this connection error?

    Read the article

  • SuperMicro BMC on OpenSuSE Linux --cannot access from LAN

    - by Kendall
    Hi, I have an (old) SMC-001 IPMI device on an (old) X6DVL-EG2 motherboard. My problem is that I cannot access the BMC from LAN. I'm also getting some interesting output from ipmitool. First, the setup. I enable Console Redirection in the BIOS, turn BIOS Redirection after POSt to "disabled". I then modprobe'ed for ipmi_msghandler, ipmi_devintf and ipmi_si. I then found ipmi0 under /dev. So far so good. Since I want console redirection over serial, I modified /boot/grub/menu.lst: http://pastebin.com/YYJmhusQ I then modified "/etc/inittab" as follows: S1:12345:respawn:/sbin/agetty -L 19200 ttyS1 ansi Networking I set as following, using "ipmitool" ipaddr: 192.168.3.164 netmask: 255.255.255.0 defgw: 192.168.3.1 The above are correct for my environment. To test it I do: ipmitool -I open chassis power off which responds by powering off the machine. When I to access from another computer on the network, however, I get an error message: host# ipmitool -I lanplus -H 192.168.10.164 -U Admin -a chassis power status Error: Unable to establish LAN session Unable to get Chassis Power Status "Admin" seems to be a valid user name: host# ipmitool -I open user list 1 2 Admin true false true USER The interesting output from ipmitool I initially mentioned: host # ipmitool -I open lan set 1 access on Set Channel Access for channel 1 failed: Request data field length limit exceeded Also, newload4:/home/gjones # ipmitool channel info 1 Channel 0x1 info: Channel Medium Type : 802.3 LAN Channel Protocol Type : IPMB-1.0 Session Support : session-less Active Session Count : 0 Protocol Vendor ID : 7154 Get Channel Access (volatile) failed: Request data field length limit exceeded The output of "ipmitool -I open lan print 1" is here: http://pastebin.com/UZyL6yyE Any help/suggestions is greatly appreciated; I've been working with this thing for a few hours now with no success.

    Read the article

  • Cisco SR520w FE - WAN Port Stops Working

    - by Mike Hanley
    I have setup a Cisco SR520W and everything appears to be working. After about 1-2 days, it looks like the WAN port stops forwarding traffic to the Internet gateway IP of the device. If I unplug and then plug in the network cable connecting the WAN port of the SR520W to my Comcast Cable Modem, traffic startings flowing again. Also, if I restart the SR520W, the traffic will flow again. Any ideas? Here is the running config: Current configuration : 10559 bytes ! version 12.4 no service pad no service timestamps debug uptime service timestamps log datetime msec no service password-encryption ! hostname hostname.mydomain.com ! boot-start-marker boot-end-marker ! logging message-counter syslog no logging rate-limit enable secret 5 <removed> ! aaa new-model ! ! aaa authentication login default local aaa authorization exec default local ! ! aaa session-id common clock timezone PST -8 clock summer-time PDT recurring ! crypto pki trustpoint TP-self-signed-334750407 enrollment selfsigned subject-name cn=IOS-Self-Signed-Certificate-334750407 revocation-check none rsakeypair TP-self-signed-334750407 ! ! crypto pki certificate chain TP-self-signed-334750407 certificate self-signed 01 <removed> quit dot11 syslog ! dot11 ssid <removed> vlan 75 authentication open authentication key-management wpa guest-mode wpa-psk ascii 0 <removed> ! ip source-route ! ! ip dhcp excluded-address 172.16.0.1 172.16.0.10 ! ip dhcp pool inside import all network 172.16.0.0 255.240.0.0 default-router 172.16.0.1 dns-server 10.0.0.15 10.0.0.12 domain-name mydomain.com ! ! ip cef ip domain name mydomain.com ip name-server 68.87.76.178 ip name-server 66.240.48.9 ip port-map user-ezvpn-remote port udp 10000 ip ips notify SDEE ip ips name sdm_ips_rule ! ip ips signature-category category all retired true category ios_ips basic retired false ! ip inspect log drop-pkt no ipv6 cef ! multilink bundle-name authenticated parameter-map type inspect z1-z2-pmap audit-trail on password encryption aes ! ! username admin privilege 15 secret 5 <removed> ! crypto key pubkey-chain rsa named-key realm-cisco.pub key-string <removed> quit ! ! ! ! ! ! crypto ipsec client ezvpn EZVPN_REMOTE_CONNECTION_1 connect auto group EZVPN_GROUP_1 key <removed> mode client peer 64.1.208.90 virtual-interface 1 username admin password <removed> xauth userid mode local ! ! archive log config logging enable logging size 600 hidekeys ! ! ! class-map type inspect match-any SDM_AH match access-group name SDM_AH class-map type inspect match-any SDM-Voice-permit match protocol sip class-map type inspect match-any SDM_ESP match access-group name SDM_ESP class-map type inspect match-any SDM_EASY_VPN_REMOTE_TRAFFIC match protocol isakmp match protocol ipsec-msft match class-map SDM_AH match class-map SDM_ESP match protocol user-ezvpn-remote class-map type inspect match-all SDM_EASY_VPN_REMOTE_PT match class-map SDM_EASY_VPN_REMOTE_TRAFFIC match access-group 101 class-map type inspect match-any Easy_VPN_Remote_VT match access-group 102 class-map type inspect match-any sdm-cls-icmp-access match protocol icmp match protocol tcp match protocol udp class-map type inspect match-any sdm-cls-insp-traffic match protocol cuseeme match protocol dns match protocol ftp match protocol h323 match protocol https match protocol icmp match protocol imap match protocol pop3 match protocol netshow match protocol shell match protocol realmedia match protocol rtsp match protocol smtp extended match protocol sql-net match protocol streamworks match protocol tftp match protocol vdolive match protocol tcp match protocol udp class-map type inspect match-any L4-inspect-class match protocol icmp class-map type inspect match-all sdm-invalid-src match access-group 100 class-map type inspect match-all dhcp_out_self match access-group name dhcp-resp-permit class-map type inspect match-all dhcp_self_out match access-group name dhcp-req-permit class-map type inspect match-all sdm-protocol-http match protocol http ! ! policy-map type inspect sdm-permit-icmpreply class type inspect dhcp_self_out pass class type inspect sdm-cls-icmp-access inspect class class-default pass policy-map type inspect sdm-permit_VT class type inspect Easy_VPN_Remote_VT pass class class-default drop policy-map type inspect sdm-inspect class type inspect SDM-Voice-permit pass class type inspect sdm-cls-insp-traffic inspect class type inspect sdm-invalid-src drop log class type inspect sdm-protocol-http inspect z1-z2-pmap class class-default pass policy-map type inspect sdm-inspect-voip-in class type inspect SDM-Voice-permit pass class class-default drop policy-map type inspect sdm-permit class type inspect SDM_EASY_VPN_REMOTE_PT pass class type inspect dhcp_out_self pass class class-default drop ! zone security ezvpn-zone zone security out-zone zone security in-zone zone-pair security sdm-zp-in-ezvpn1 source in-zone destination ezvpn-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-out-ezpn1 source out-zone destination ezvpn-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-ezvpn-out1 source ezvpn-zone destination out-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-self-out source self destination out-zone service-policy type inspect sdm-permit-icmpreply zone-pair security sdm-zp-out-in source out-zone destination in-zone service-policy type inspect sdm-inspect-voip-in zone-pair security sdm-zp-ezvpn-in1 source ezvpn-zone destination in-zone service-policy type inspect sdm-permit_VT zone-pair security sdm-zp-out-self source out-zone destination self service-policy type inspect sdm-permit zone-pair security sdm-zp-in-out source in-zone destination out-zone service-policy type inspect sdm-inspect ! bridge irb ! ! interface FastEthernet0 switchport access vlan 75 ! interface FastEthernet1 switchport access vlan 75 ! interface FastEthernet2 switchport access vlan 75 ! interface FastEthernet3 switchport access vlan 75 ! interface FastEthernet4 description $FW_OUTSIDE$ ip address 75.149.48.76 255.255.255.240 ip nat outside ip ips sdm_ips_rule out ip virtual-reassembly zone-member security out-zone duplex auto speed auto crypto ipsec client ezvpn EZVPN_REMOTE_CONNECTION_1 ! interface Virtual-Template1 type tunnel no ip address ip virtual-reassembly zone-member security ezvpn-zone tunnel mode ipsec ipv4 ! interface Dot11Radio0 no ip address ! encryption vlan 75 mode ciphers aes-ccm ! ssid <removed> ! speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0 station-role root ! interface Dot11Radio0.75 encapsulation dot1Q 75 native ip virtual-reassembly bridge-group 75 bridge-group 75 subscriber-loop-control bridge-group 75 spanning-disabled bridge-group 75 block-unknown-source no bridge-group 75 source-learning no bridge-group 75 unicast-flooding ! interface Vlan1 no ip address ip virtual-reassembly bridge-group 1 ! interface Vlan75 no ip address ip virtual-reassembly bridge-group 75 bridge-group 75 spanning-disabled ! interface BVI1 no ip address ip nat inside ip virtual-reassembly ! interface BVI75 description $FW_INSIDE$ ip address 172.16.0.1 255.240.0.0 ip nat inside ip ips sdm_ips_rule in ip virtual-reassembly zone-member security in-zone crypto ipsec client ezvpn EZVPN_REMOTE_CONNECTION_1 inside ! ip forward-protocol nd ip route 0.0.0.0 0.0.0.0 75.149.48.78 2 ! ip http server ip http authentication local ip http secure-server ip http timeout-policy idle 60 life 86400 requests 10000 ip nat inside source list 1 interface FastEthernet4 overload ! ip access-list extended SDM_AH remark SDM_ACL Category=1 permit ahp any any ip access-list extended SDM_ESP remark SDM_ACL Category=1 permit esp any any ip access-list extended dhcp-req-permit remark SDM_ACL Category=1 permit udp any eq bootpc any eq bootps ip access-list extended dhcp-resp-permit remark SDM_ACL Category=1 permit udp any eq bootps any eq bootpc ! access-list 1 remark SDM_ACL Category=2 access-list 1 permit 172.16.0.0 0.15.255.255 access-list 100 remark SDM_ACL Category=128 access-list 100 permit ip host 255.255.255.255 any access-list 100 permit ip 127.0.0.0 0.255.255.255 any access-list 100 permit ip 75.149.48.64 0.0.0.15 any access-list 101 remark SDM_ACL Category=128 access-list 101 permit ip host 64.1.208.90 any access-list 102 remark SDM_ACL Category=1 access-list 102 permit ip any any ! ! ! ! snmp-server community <removed> RO ! control-plane ! bridge 1 protocol ieee bridge 1 route ip bridge 75 route ip banner login ^CSR520 Base Config - MFG 1.0 ^C ! line con 0 no modem enable line aux 0 line vty 0 4 transport input telnet ssh ! scheduler max-task-time 5000 end I also ran some diagnostics when the WAN port stopped working: 1. show interface fa4 FastEthernet4 is up, line protocol is up Hardware is PQUICC_FEC, address is 0026.99c5.b434 (bia 0026.99c5.b434) Description: $FW_OUTSIDE$ Internet address is 75.149.48.76/28 MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, 100BaseTX/FX ARP type: ARPA, ARP Timeout 04:00:00 Last input 01:08:15, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/23/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 1000 bits/sec, 0 packets/sec 336446 packets input, 455403158 bytes Received 23 broadcasts, 0 runts, 0 giants, 37 throttles 41 input errors, 0 CRC, 0 frame, 0 overrun, 41 ignored 0 watchdog 0 input packets with dribble condition detected 172529 packets output, 23580132 bytes, 0 underruns 0 output errors, 0 collisions, 2 interface resets 0 unknown protocol drops 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out 2. show ip route Gateway of last resort is 75.149.48.78 to network 0.0.0.0 C 192.168.75.0/24 is directly connected, BVI75 64.0.0.0/32 is subnetted, 1 subnets S 64.1.208.90 [1/0] via 75.149.48.78 S 192.168.10.0/24 is directly connected, BVI75 75.0.0.0/28 is subnetted, 1 subnets C 75.149.48.64 is directly connected, FastEthernet4 S* 0.0.0.0/0 [2/0] via 75.149.48.78 3. show ip arp Protocol Address Age (min) Hardware Addr Type Interface Internet 75.149.48.65 69 001e.2a39.7b08 ARPA FastEthernet4 Internet 75.149.48.76 - 0026.99c5.b434 ARPA FastEthernet4 Internet 75.149.48.78 93 0022.2d6c.ae36 ARPA FastEthernet4 Internet 192.168.75.1 - 0027.0d58.f5f0 ARPA BVI75 Internet 192.168.75.12 50 7c6d.62c7.8c0a ARPA BVI75 Internet 192.168.75.13 0 001b.6301.1227 ARPA BVI75 4. sh ip cef Prefix Next Hop Interface 0.0.0.0/0 75.149.48.78 FastEthernet4 0.0.0.0/8 drop 0.0.0.0/32 receive 64.1.208.90/32 75.149.48.78 FastEthernet4 75.149.48.64/28 attached FastEthernet4 75.149.48.64/32 receive FastEthernet4 75.149.48.65/32 attached FastEthernet4 75.149.48.76/32 receive FastEthernet4 75.149.48.78/32 attached FastEthernet4 75.149.48.79/32 receive FastEthernet4 127.0.0.0/8 drop 192.168.10.0/24 attached BVI75 192.168.75.0/24 attached BVI75 192.168.75.0/32 receive BVI75 192.168.75.1/32 receive BVI75 192.168.75.12/32 attached BVI75 192.168.75.13/32 attached BVI75 192.168.75.255/32 receive BVI75 224.0.0.0/4 drop 224.0.0.0/24 receive 240.0.0.0/4 drop 255.255.255.255/32 receive Thanks in advance, -Mike

    Read the article

  • Could not continue scan with NOLOCK due to data movement during installation

    - by dbdev1
    Hi, I am running Windows Server 2008 Standard Edition R2 x64 and I installed SQL Server 2008 Developer Edition. All of the preliminary checks run fine (Apart from a warning about Windows Firewall and opening ports which is unrelated to this and shouldn't be an issue - I can open those ports). Half way through the actual installation, I get a popup with this error: Could not continue scan with NOLOCK due to data movement. The installation still runs to completion when I press ok. However, at the end, it states that the following services "failed": database engine services sql server replication full-text search reporting services How do I know if this actually means that anything from my installation (which is on a clean Windows Server setup - nothing else on there, no previous SQL Servers, no upgrades, etc) is missing? I know from my programming experience that locks are for concurrency control and the Microsoft help on this issue points to changing my query's lock/transactions in a certain way to fix the issue. But I am not touching any queries? Also, now that I have installed the app, when I login, I keep getting this message: TITLE: Connect to Server Cannot connect to MSSQLSERVER. ADDITIONAL INFORMATION: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server) (Microsoft SQL Server, Error: 67) For help, click: http://go.microsoft.com/fwlink?ProdName=Microsoft+SQL+Server&EvtSrc=MSSQLServer&EvtID=67&LinkId=20476 BUTTONS: OK I went into the Configuration Manager and enabled named pipes and restarted the service (this is something I have done before as this message is common and not serious). I have disabled Windows Firewall temporarily. I have checked the instance name against the error logs. Please advise on both of these errors. I think these two errors are related. Thanks

    Read the article

  • Static routing on a TP-Link TL-WR1043ND

    - by igor
    My home network setup looks like this: Both routers are TP-Link TL-WR1043ND routers. The basement router handles all devices in the house that are connected via cable, handing out addresses for the 10.89.49.0/24 network via DHCP. Wireless doesn’t really work from the basement, as the signal is too weak, so I have disabled it. To do WiFi, I have added a second (identical) router downstairs. On the WAN side it is assigned the 10.89.49.101 IP address from the basement router, and on its LAN it provides the 10.89.7.0/24 network. Basic internet access works flawlessly from any device this way. I am now facing the problem that I am not able to communicate (e.g. SSH) between all devices, wired or wireless. I am able to connect from a wireless device to a wired device, for example SSH-ing from 10.89.7.X to 10.89.49.Y, but it doesn’t work the other way round—despite the fact that I have added a static route to the basement router: Does anybody have any idea on how to solve it? Both routers have already been upgraded to use the most recent firmware from TP-Link.com (Build 110429), to no avail. Errata: I would like to stick with the official firmware, switching to something like DD-WRT or OpenWrt only as a last resort.

    Read the article

  • SQL Server 2008 Express + Reporting Services on Windows 7

    - by TimothyP
    I'm trying to install SQL Server Express 2008 and Reporting Services on a x64 Windows 7 Machine for development purposes. I've installed SQL Server 2008 Express with the Microsoft Web Platform Installer I had to manually enable the SQL Server Browser in the Sql Server Configuration Manager and tried to enable the SQL Server Agent but that simply doesn't work. Keeps throwing an RPC error: "The remote procedure call failed. [0x800706be]". The start mode is set to Disabled and I cannot change it. Even though I selected the SQL Server Express with advanced services in the web platform installer I could not find any reference to SQL Server Reporting Services so I used the SQL Server Installation Center x64 application to "upgrade" to SQL Server Express 2008 with advanced services... this installed many things but still I couldn't find any reference to SQL Server Reporting Services other than an application called: "Reporting Services Configuration Manager" This opens up a dialog called "Reporting Services Configuration Connection" which is asking for a server name (shows the name of my machine) and a Find button. When I click the find button I get: "Unable to connect to the Reporting Server WMI provider. Details: Invalid Namespace". I found some references on the web to solve this problem, but they refer to a directory: "%ProgamFiles%\Microsoft SQL Server\MSRS10.SQL2008\Reporting Services\" which does not exist anywhere on my system. (The directories for SQL Server are there, but there is no Reporting Services directory anywhere). What am I doing wrong here? Wasn't the web platform installer supposed to handle all this? Thnx for any advice. PS: Most google results refer to 2005 vs 2008 problems, but I never had 2005 installed on this system, it's a newly installed development machine.

    Read the article

  • Make Thundirbird use and sync with Gmail Spam facility

    - by Senthil
    I am using Thundirbird 3.1.7. I am using Gmail with it. When I mark a message as spam in Thunderbird, I want it to go to Gmail's spam folder. But it is not happening. The mail is only marked as spam and stays in Gmail's inbox. How can I setup Thunderbird so that when I mark a message as spam in thundirbird, it goes to spam folder in both Thunderbird and Gmail? FYI: I have disabled Thunderbird's own adaptive spam controls so that it doesn't interfere. I am perfectly fine with Gmail's spam facility and don't want Thunderbird to add another layer of spam filtering. Still Thunderbird doesn't send emails to Gmail's spam. Update I figured that dragging and dropping the email to the spam folder in Thunderbird does the job. But is it the same as marking the email as spam in Gmail's interface? i.e. Gmail will do stuff when you mark an email as spam so that it can filter out similar messages in the future. Does it happen when I do this drag and drop thing too? Are they the same?

    Read the article

  • Need Help Accessing the Vista Wampserver localhost from Virtual PC 2007 running an XP VM.

    - by Reg
    (I had posted this on stack overflow but it was suggested there that I post it here instead). I have a Vista laptop on which I'm running wampserver. I have Virtual PC 2007 setup with Windows XP running on the VM. My goal is to be able to use the XP VM to run IE6 to view the localhost in the Vista wampserver. I'm not interested in having the XP VM have any access to the internet -- only to my Vista wampserver's localhost. The vista wampserver works fine. As suggested on a blog I read, I installed the loopback adapter on Vista and I set the loopback to 192.168.21.1 and I set the xp vm ip to 192.168.21.2. I am able to successfully ping the vista-loopback adapter from the xp vm. I've turned the wampserver to "server online", and I've disabled the firewalls in both the vista host and the xp vm. But for some reason, I still can't seem to get the virtual XP to see the localhost on the vista wampserver. I've tried using the vista //name, and I've tried the ip 192.168.21.1 directly and with the port. For whatever its worth, I'm not able to see anything under the XM VM's network places (though I don't know if I'm supposed to be able to see anything). So at this point I'm stuck and I'm still not sure how to get this XP VM to "talk" to my vista wampserver localhost. Any advice on how to fix this problem is much appreciated. Thanks in advance for your help. -R

    Read the article

  • How can I make my PCI-E graphics card visible to Ubuntu when the motherboard has integrated graphics

    - by Norman Ramsey
    I have a Gigabyte GA-MA74GM-S2 motherboard with integrated graphics that shows up on lspci as an ATI Radeon 2100. I also bought a PCI-Express Nvidia graphics card so I could use the VDPAU feature on Linux (plays H.264 in hardware). The BIOS has three settings about which display to initialize first: Integrated graphics PCI graphics PCI-Express graphics (PEG) I set the BIOS on PEG, but I cannot get anything, not even a splash screen or POST messages, to emerge from the PCI-Express graphics card. (I'm using a DVI connector; the card also has an HDMI output.) I cannot get the kernel lspci to see the graphics card; the only VGA controller it acknowledges is the integrated one. Running dmidecode acknowledges the existence of an x16 PCI Express slot, and it says Current usage: Unknown There is an additional BIOS setting called "Internal Graphics Mode" which is normally set to "Auto" which means it is supposed to prefer a PCI Express VGA card. I set it to "Disabled" which now means I'm getting no output at all. I will soon be learning how to do a BIOS reset! Other information: The PCI-E card is a MSI N210-MD512H GeForce 210. This is a fanless card. Although there are no fans to see turning, the heat sink on the PCI-E card is definitely getting hot, so the card is getting some sort of power. It gets all its power from the PCI-E slot; there is no external power connector. The BIOS is an AMI Award BIOS. My question: how can I make the PCI Express graphics card visible to Ubuntu?

    Read the article

  • Open Source PDF reader for windows as an alternative to Adobe reader

    - by Tom Feiner
    With the latest javascript vulnerabilities in Adobe reader and bloat it has aquired over the years, I've been thinking of moving the network I'm in charge of to a different product for PDF reading on Windows. The ideal PDF reader should be something that is: Small in size (Adobe reader is more than 200MB these days after installation). As secure by default as possible (For example, javascript disabled by default). Nice looking and easy to use interface. Not bloated with features (I just want to read PDFs, that's it). Does not install any toolbars/unwanted add ons/spyware. Does not display any ads while viewing PDFs. Preferably Open Source. (this pretty much ensures no ads). Full Unicode support. Idealy , something like evince from gnome, will be the best option, but unfortunately that's not available on Windows. Foxit is an option, as it is small, and has a nice interface. But it still has javascript enabled by default which might lead to vulnerabilities - and it installs a toolbar , and displays ads while reading PDFs which is distracting. There is a site dedicated to Open Source PDF readers, pdfreaders.org, however, the Windows pdf readers each have their problems, mostly the interface is not as convenient (as evince, adobe or foxit). Here's a list of all PDF software from WikiPedia. There's a "Viewers" section for each OS. What Windows PDF reader would you recommend ?

    Read the article

  • Windows Server 2008R2 - can't change or remove the default gateway

    - by disserman
    We've installed VMWare Server 2.0 on Windows 2008R2. After some time playing with it (actually only removing host-only and nat networks, and binding adapters to the specified vmnets) we've noticed a strange problem: if you change or remove the default gateway on the network card, the server completely loses a network connection you can't ping it from the subnet, it also can't connect to anyone. When the gateway is removed and a server tries to connect to the other machines, I can see some incoming packets using a sniffer, but I believe they are damaged in some kind (I'm not a mega-guru in TCP/IP and can't find a mistake in a binary translation of the packet) because the other side doesn't respond. What we tried: removed vmware server using add/remove programs deleted everything related to the vmware server and all installed network adapters in the windows registry double checked for the vmware bridged protocol driver file, it's physically absent and no any links in the registry. performed a tcp/ip reset with netsh and disabled/enabled all network adapters in the device manager to recreate a registry keys for them. tried another network adapter. and the situation is the same: as soon you remove or change the default gateway, windows stops working. The total absurd of the situation is that the default gateway points to the non-existing IP. But when it's set, you can ping a server from the subnet, when you remove it - you can't. Any help? I'm starting thinking the new build of the VMWare Server is some kind of the malware... :)

    Read the article

  • MySQL remote access not working - Port Close?

    - by dave.zap
    I am not able to get a remote connection established to MySQL. From my pc I am able to telnet to 3306 on the existing server, but when I try the same with the new server it hangs for few minutes then returns # mysql -utest3 -h [server ip] -p Enter password: ERROR 2003 (HY000): Can't connect to MySQL server on '[server ip]' (110) Here is some output from the server. # nmap -sT -O localhost -p 3306 ... PORT STATE SERVICE 3306/tcp closed mysql ... # netstat -anp | grep mysql tcp 0 0 [server ip]:3306 0.0.0.0:* LISTEN 6349/mysqld unix 2 [ ACC ] STREAM LISTENING 12286 6349/mysqld /DATA/mysql/mysql.sock # netstat -anp | grep 3306 tcp 0 0 [server ip]:3306 0.0.0.0:* LISTEN 6349/mysqld unix 3 [ ] STREAM CONNECTED 3306 1411/audispd # lsof -i TCP:3306 COMMAND PID USER FD TYPE DEVICE SIZE/OFF NODE NAME mysqld 6349 mysql 10u IPv4 12285 0t0 TCP [domain]:mysql (LISTEN) I am running... OS CentOS release 5.8 (Final) mysql 5.5.28 (Remi) Note: Internal connections to mysql work fine. I have disabled IPtables, the box has no other firewall, it runs Apache on port 80 and ssh no problem. Had followed this tutorial - http://www.cyberciti.biz/tips/how-do-i-enable-remote-access-to-mysql-database-server.html I have bound the IP address in my.cnf user=mysql bind-address = [sever ip] port=3306 I even started over by deleting the mysql folder in my datastore and running mysql_install_db --datadir=/DATA/mysql --force Then recreated all the users as per the manual... http://dev.mysql.com/doc/refman/5.5/en/adding-users.html I have created one test user CREATE USER 'test'@'%' IDENTIFIED BY '[password]'; GRANT ALL PRIVILEGES ON *.* TO 'test'@'%' WITH GRANT OPTION; FLUSH PRIVILEGES; So all I can see is that the port is not really open. Where else might I look? thanks

    Read the article

  • Hyper V Server 2012 Remote Management Using Workgroup

    - by Chris Kolenko
    I'm trying to remotely manage Hyper V server 2012 from a windows 8 pc, both client and server are on a workgroup. I've spent about 3-4 hours trying to get this working with no luck so far trying the following: Creating a new administrator on the server with the same details as the client ie. username / password. Add an entry into my hosts file to point to the remote ip by server name. Tried using HVRemote. Disabled both firewalls. The error that I'm getting is RPC Service Unavailable. How can I accomplish what I'm trying to do? Update Some of the operations on the Hyper-V Manager work. IE. Virtual Switch Works. I can open the New VM Wizard. I run into an error when creating a new Virtual Hard Disk tho. I've tried creating a VM without a hard disk, which works. Using the new hard disk wizard does not work either. I still can not see any Virtual Machines. RPC server unavailable. Unable to establish communication between 'ServerName' and 'ClientName'

    Read the article

  • Exchange 2007 two node cluster setup on Windows 2008 Enterprise, install error

    - by Shadow00Caster
    I am installing Microsoft Exchange 2007 x64 in a two node environment using Microsoft Windows 2008 Enterprise x64. The Failover Cluster is all setup properly and following best practices for setting up the windows clustering for use with Exchange 2007. All the validation tests pass on the cluster and all of that portion is working fine. The problem is when I go to install the first Exchange node as an Active mailbox in configuration for a two node CCR. It gets all the way through the first 3 steps (Copy Exchange Files, Management Tools, Mailbox Role) and then fails on the 4th step 'Clustered Mailbox Server' with the following error: Error: The clustered mailbox server's group 'XXXX' was not found, and should already exist. Firewalls are all disabled, DNS is all setup properly, the environment has 3 domain controllers all 2k8 ent x64, all replication works. The name I pick for the CCR cluster (XXX) does not exist in AD or in DNS. I have attempted this install from both of the two Exchange nodes and multiple times .. tried with different names. I have been banging my head against the wall for days working on this and would appreciate any feedback on the issue.

    Read the article

  • CoreStore Encryption Error on Mac Lion

    - by Michael
    I am trying to encrypt an external drive using diskutil CoreStorage on Mac Lion 10.7.4. I thought the only requirements were that the drive have GUID partition scheme and Journaled HFS+ file system. I think my drive is configured accordingly but when I type the following command I get an error message back: Michaels-MacBook-Pro:~ Michael$ diskutil cs convert disk2 -passphrase TestPassword Error converting disk to CoreStorage: The given file system is not supported on Core Storage (-69756) Here are the details reported for the drive in question: Michaels-MacBook-Pro:~ Michael$ diskutil list disk2 /dev/disk2 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *500.1 GB disk2 1: EFI 209.7 MB disk2s1 2: Apple_HFS Test1 499.8 GB disk2s2 Michaels-MacBook-Pro:~ Michael$ diskutil list disk2 /dev/disk2 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *500.1 GB disk2 1: EFI 209.7 MB disk2s1 2: Apple_HFS Test1 499.8 GB disk2s2 Michaels-MacBook-Pro:~ Michael$ diskutil info disk2s2 Device Identifier: disk2s2 Device Node: /dev/disk2s2 Part of Whole: disk2 Device / Media Name: Test1 Volume Name: Test1 Escaped with Unicode: Test1 Mounted: Yes Mount Point: /Volumes/Test1 Escaped with Unicode: /Volumes/Test1 File System Personality: Journaled HFS+ Type (Bundle): hfs Name (User Visible): Mac OS Extended (Journaled) Journal: Journal size 40960 KB at offset 0xe8e000 Owners: Disabled Partition Type: Apple_HFS OS Can Be Installed: Yes Media Type: Generic Protocol: FireWire SMART Status: Not Supported Volume UUID: 1024D0B8-1C45-3057-B040-AE5C3841DABF Total Size: 499.8 GB (499763888128 Bytes) (exactly 976101344 512-Byte-Blocks) Volume Free Space: 499.3 GB (499315826688 Bytes) (exactly 975226224 512-Byte-Blocks) Device Block Size: 512 Bytes Read-Only Media: No Read-Only Volume: No Ejectable: Yes Whole: No Internal: No I'm a little concerned that the "Partition Type: Apple_HFS" entry is causing the problem, but I don't know how to change that. I only seem to be able to control the "File System Personality: Journaled HFS+" in Disk Utility. Can anyone shed some light on this for me?

    Read the article

< Previous Page | 116 117 118 119 120 121 122 123 124 125 126 127  | Next Page >