Search Results

Search found 3496 results on 140 pages for 'reset'.

Page 120/140 | < Previous Page | 116 117 118 119 120 121 122 123 124 125 126 127  | Next Page >

  • WiFi signal is lost every 3 minutes

    - by Software Monkey
    For several weeks now my Android phone has been losing it's WiFi signal momentarily, typically at about 3 minute intervals (about 3 minutes, 1.5 seconds) and occasionally at some longer interval that always seems to be just over 3 minutes. This causes an interruption of several seconds while the WiFi connection is re-established and typically fails any kind of download/streaming that is happening, makes web sites "unreachable" and generally makes the phone unusable as a data device due to the frequency. The signal remains down for about a second, but the phone takes a few more seconds to reconnect to the router. This happens regardless of proximity to the router, which otherwise show a very strong signal - usually -40 to -30 dBm or better in the same room, nowhere less than 060 dBm anywhere in the house. Changing channels does not help (I've tried 1, 4, 8 and 9). Nor does turning off the router's guest access. Nor does turning off the 5.0 GHz band. Monitoring the signal on my phone with WiFi analyzer, shows all WiFi signals on all channels drop to nothing when the WiFi connection is lost (there are two other networks on different channels which are strong enough to be relevant, with about 6 others constantly fading in and out). WiFi analyzer shows 3 separate signals for my router, the main 2.4 GHz, the guest 2.4 GHz and the 5.0 GHz. Using WiFi Analyzer on my wife's phone side-by-side shows no change in signal when my phone drops, nor does her phone drop. Monitoring the signal using our laptop, side-by-side likewise shows no signal loss and likewise the laptop does not lose it's WiFi connection. But, at work, the phone seems to not exhibit the same behavior, or, if it does, it's very occasional. Monitoring it all day at work I only saw the signal drop 3 or 4 times. The signal strength of the various networks there is comparatively weak. AT&T were super helpful: "Sorry, we can't help you with WiFi problems. You could try doing a factory reset on your phone". </sarcasm The router is relatively new, but has been working fine with this phone since last Dec. Phone : Motorola Atrix (about 8 months old). Router : Belkin N750 DB (F9K1103 v1 (01C)). Router Firmware: 1.00.46 (2011/10/28 6:37:11). Security : WPA/WPA2-Personal (PSK)

    Read the article

  • How to configure ASP.NET MVC 3 on IIS 6 (Windows 2003 R2)

    - by Nedcode
    I am getting 403 Directory Listing Denied for the root and 404 for an action that I know should exist. Background: I have build and deployed an ASP.NET MVC 2 applcation a long time ago. Later I upgraded it to MVC 3 and it is still working with not configuration changes. Setting it up on a windows 2003 R2 (Standard) initialy was a pain, but after a couple of days(yes, days) struggling it started working. Now I have to do the same with the same application on a different server (2003 R2 Standard again) on a different network. .Net 4 is installed and allowed ASP.NET MVC 3 is also installed By default IIS is set to use .net 4 I verify aspnet_isapi.dll used in application extension are from version 4.0.30319 .NET asemblies folder. I also added the wildcard mapping to aspnet_isapi.dll and unchecked verify file exists. Under Directory Security in Authentication Methods I have disabled anonymos access and enabled Integrated Windows authentication(same as the one on the server that it works) I have copied the same web.config with the <authentication mode="Windows" /> <authorization> <deny users="?" /> </authorization> I have set Read & Execute, List Folder Contents, and Read for the Networkservice account(under which the app pool is working). Also I have set the same for Network account, IIS_WPG, ASPNET and IUSR_MAchineName. I do not have an EnableExte??nsionlessUrls but even if I create it and set it to true or false it does not help. I also tried http://haacked.com/archive/2010/12/22/asp-net-mvc-3-extensionless-urls-on-iis-6.aspx and it did not help. But I kept getting 403 Directory Listing Denied for the root and 404 for an action that I know should exist. Web Platform installer was then used to re-install and possibly update .net, asp.net etc. I then noticed IIS was reset to default. So I added the wildcard mapping again. No, luck still 403. I exported configuration files from the working server setup and created new default app pool and new default website using those configurations. Still I get 403 Directory Listing Denied for the / and 404 for any action I try.

    Read the article

  • Some emails are being delivered, some returned

    - by Tom Broucke
    I have my own VPS where a site is running (control panel: directadmin). When I send mails, some are being delivered (hotmail, gmail, [email protected] ,...), others are not ([email protected]), others are delivered after being greylisted ([email protected]). /var/log/exim/mainlog What could be the cause of this? Is the problem Sender-Side or Receiver-Side? case 1: [email protected] (delivered) 2012-06-20 15:02:03 1ShKXr-0005Sc-7g <= [email protected] U=apache P=local S=1319 T="Password reset" from <[email protected]> for [email protected] 2012-06-20 15:02:03 1ShKXr-0005Sc-7g gmail-smtp-in-v4v6.l.google.com [2a00:1450:8005::1b] Network is unreachable 2012-06-20 15:02:03 1ShKXr-0005Sc-7g => [email protected] F=<[email protected]> R=lookuphost T=remote_smtp S=1355 H=gmail-smtp-in-v4v6.l.google.com [173.194.67.27] X=TLSv1:RC4-SHA:128 C="250 2.0.0 OK 1340196103 cp4si34336466wib.14" 2012-06-20 15:02:03 1ShKXr-0005Sc-7g Completed case 2: [email protected] (not being delivered) 2012-06-21 09:57:14 1ShcGQ-0007No-5H <= [email protected] H=localhost ([91.230.245.141]) [127.0.0.1] P=esmtpa A=login:[email protected] S=740 [email protected] T="hey" from <[email protected]> for [email protected] 2012-06-21 09:57:14 1ShcGQ-0007No-5H ** [email protected] F=<[email protected]> R=virtual_aliases: 2012-06-21 09:57:14 1ShcGQ-0007Nt-7Z <= <> R=1ShcGQ-0007No-5H U=mail P=local S=1546 T="Mail delivery failed: returning message to sender" from <> for [email protected] 2012-06-21 09:57:14 1ShcGQ-0007No-5H Completed 2012-06-21 09:57:14 1ShcGQ-0007Nt-7Z => info <[email protected]> F=<> R=virtual_user T=virtual_localdelivery S=1643 2012-06-21 09:57:14 1ShcGQ-0007Nt-7Z Completed case 3: [email protected] (greylisted) 2012-06-21 15:29:02 1ShhRW-000862-BV <= [email protected] H=localhost ([91.230.245.141]) [127.0.0.1] P=esmtpa A=login:[email protected] S=782 [email protected] T="testmail squirrel" from <[email protected]> for [email protected] 2012-06-21 15:29:02 1ShhRW-000862-BV SMTP error from remote mail server after RCPT TO:<[email protected]>: host mx-cluster-b1.one.com [195.47.247.194]: 450 4.7.1 <[email protected]>: Recipient address rejected: Greylisted for 5 minutes 2012-06-21 15:29:02 1ShhRW-000862-BV == [email protected] R=lookuphost T=remote_smtp defer (-44): SMTP error from remote mail server after RCPT TO:<[email protected]>: host mx-cluster-b2.one.com [195.47.247.195]: 450 4.7.1 <[email protected]>: Recipient address rejected: Greylisted for 5 minutes Notice that the "from" in case1 differs in case2: [email protected] or [email protected]. Thanks for your time!

    Read the article

  • Mysql innoDB corruption after server crash

    - by Ward Loockx
    Yesterday my server died because an outage in the data center. Today it's back up, but having some problems with mysql. First of all my mysql server was not able to start. For this reason I deleted the files ib_logfile0 and ib_logfile1 in /var/lib/mysql folder (I still have the old failing files). After this my server was able to startup again. But now I see a lot of issues in the mysql log file. Sep 1 09:43:55 * mysqld: 120901 9:43:55 InnoDB: Error: page 70944 log sequence number 8 1483471899 Sep 1 09:43:55 * mysqld: InnoDB: is in the future! Current system log sequence number 5 612394935. Sep 1 09:43:55 * mysqld: InnoDB: Your database may be corrupt or you may have copied the InnoDB Sep 1 09:43:55 * mysqld: InnoDB: tablespace but not the InnoDB log files. See Sep 1 09:43:55 * mysqld: InnoDB: http://dev.mysql.com/doc/refman/5.1/en/forcing-recovery.html When I check the docs on mysql.com, I found that I need to recover my database with backups. I have a backup but not sure what's the good way on importing it. Or is there a way to recover without having to re-import the database again? So if I'm correct I need to put innodb_force_recovery to 4 in mysql and delete all current data and re-import? Is there a way to do this without having downtime? I also have one slave running. This slave has the current status now: Last_Error: Relay log read failure: Could not parse relay log event entry. The possible reasons are: the master's binary log is corrupted (you can check this by running 'mysqlbinlog' on the binary log), the slave's relay log is corrupted (you can check this by running 'mysqlbinlog' on the relay log), a network problem, or a bug in the master's or slave's MySQL code. If you want to check the master's binary log or slave's relay log, you will be able to know their names by issuing 'SHOW SLAVE STATUS' on this slave. How can I totally reset the slave after the new import on the master has happend? Hopefully we can find a solution without not to much downtime. Thanks!

    Read the article

  • VMware server 2.0 SYN/ACK repeating issues

    - by user65579
    VMWare Server 2.0.0 Build 122956 I am having some issues with connecting into a guest VM (Ubuntu linux 4.4.3-4 lucid) running under VMware 2.0 on a windows server host. All connections to and from the VM's work fine, except for FTP. I thought the issue was the FTP daemon at first but it has been ruled out that it is not the daemon or the server itself. When you try to connect to the FTP server from outside of the host OS it fails with a "421 Service not available" but when you try and connect from the local VM or from the host OS the connection goes through fine. I have ran many packet sniffs using wireshark/tcpdump from the VM, the host OS, and the client connecting, the most informative is the host OS. I have attached a PNG of the relavant packets that were captured. I viewed some other network traffic that was sniffed (WWW specifically) and it seems to do the same syn/ack repeating but the user doesnt see any issues. I have disabled the firewall and the issues persisits, I have tried with specific allow rules to ensure the data is allowed and no changes. It appears like VMware attempts to do the ICMP redirect and it works, but then it vmware repeats the packets sent so you get 3 syn/ack's for every one syn from the client. Also VMWare appears to be attempting to establish an FTP connection between the HOST OS and the GUEST OS, because I see the second SYN sent from the HOST OS to the GUEST to initiate a new connection, and it get the appropriate SYN/ACK followed by an ACK, but the client never sees any of this from its end. EG. syn from client syn/ack from host OS to client syn/ack from guest OS to client syn/ack from host OS to client The same thing happens when the connection reset is attempted, RST's start being sent and repeated, the server responds with a valid header to continue the FTP handshake but the RST acknowledgement is allready issued and things are closed. I am not 100% if this is a bug in VMware or possibly a VMNetwork missconfiguration. Does anyone have any thoughts on where exactly the issue could be, things to try to verify or rule out? I have linked to a picture of the relevant packets sniffed from the host OS. http://img18.imageshack.us/img18/7789/vmwareftpconnection.jpg

    Read the article

  • How to setup GIT repo on server with need for working dir (non- bare)

    - by OrangeTux
    I want to have configurate a GIT repo for a website. Multiple users will have a clone of the repo on their local machine and on the end of each day they push their work to the server. I can setup a bare repo, but I want a working dir/non-bare repository. The idea is that the working dir of the repository will the root folder for the website. At the end of each day all changes will be visible directly. But I can't find a way to do this. Initializing the server repo with git init gives the following error when a client is trying to push some files: git push origin master [email protected]'s password: Counting objects: 3, done. Writing objects: 100% (3/3), 227 bytes, done. Total 3 (delta 0), reused 0 (delta 0) remote: error: refusing to update checked out branch: refs/heads/master remote: error: By default, updating the current branch in a non-bare repository remote: error: is denied, because it will make the index and work tree inconsistent remote: error: with what you pushed, and will require 'git reset --hard' to match remote: error: the work tree to HEAD. remote: error: remote: error: You can set 'receive.denyCurrentBranch' configuration variable to remote: error: 'ignore' or 'warn' in the remote repository to allow pushing into remote: error: its current branch; however, this is not recommended unless you remote: error: arranged to update its work tree to match what you pushed in some remote: error: other way. remote: error: remote: error: To squelch this message and still keep the default behaviour, set remote: error: 'receive.denyCurrentBranch' configuration variable to 'refuse'. To ssh://[email protected]/home/orangetux/www/ ! [remote rejected] master -> master (branch is currently checked out) error: failed to push some refs to 'ssh://[email protected]/home/orangetux/www/' So I'm wondering if this the right way to setup a GIT repo for a website? If so, how do I have to do this? If not, what is a better way to setup a GIT repo for the development of a website? EDIT you can't push to a non-bare repository Oke, clear. But whats the way to solve my problem? Create a bare repository on the server and have a clone of this repo on the same server in the htdocs folder? This looks a bit clumsy to me. To see the result of a commit I've to clone the repository each time.

    Read the article

  • Confused with DKIM, SPF and Exim Configs

    - by 0pt1m1z3
    I've now spent 2 hours trying to figure out this issue and I am about to give up and go to bed. I've been having issues with Gmail rejecting emails from my VPS server because of false spam alerts (probably caused by lfd sending too many emails). So I changed my Exim config to send emails from a different IP (my VPS comes with 3) and that fixed the issue. I also enabled DKIM and SPF on my domains for added measure. But now, all my emails appear as ("From: Sender Name via server.domain1.com") where server.domain1.com is my VPS hostname. I previously had the same issue in Outlook and turning off "Set SMTP Sender: headers" solved that problem. But I believe adding the DKIM and SPF now makes Gmail add "via server.domain1.com" to my messages. How do I fix this? This is a typical header for a message (as it appears at gmail): Delivered-To: [email protected] Received: by 10.60.44.163 with SMTP id f3csp248622oem; Thu, 29 Mar 2012 21:23:18 -0700 (PDT) Received: by 10.50.106.200 with SMTP id gw8mr452788igb.10.1333081398523; Thu, 29 Mar 2012 21:23:18 -0700 (PDT) Return-Path: <[email protected]> Received: from domain2.com ([X.X.X.X]) by mx.google.com with ESMTPS id y1si810998igb.3.2012.03.29.21.23.18 (version=TLSv1/SSLv3 cipher=OTHER); Thu, 29 Mar 2012 21:23:18 -0700 (PDT) Received-SPF: pass (google.com: domain of [email protected] designates X.X.X.X as permitted sender) client-ip=X.X.X.X; Authentication-Results: mx.google.com; spf=pass (google.com: domain of [email protected] designates X.X.X.X as permitted sender) [email protected]; dkim=pass [email protected] DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed; d=server.domain1.com; s=default; h=Date:Message-Id:From:Content-type:MIME-Version:Subject:To; bh=wF8bBRgh01EYg4t5DAeVPv1Ps906UVIeRnQCb/HvSYw=; b=k/Pg7lnrO+Ud/z1mOTv+O/3DiJzzQgyBhfIizIaFHM8tF/eNJt5P2k+9yQB224sxYstZIWwVRBJmiqvcM1QhARv1HWqWma0crppZ3JOn+LRHANan634OBi+58SIRA+gu; Received: (Exim 4.77) id 1SDTVE-0005HA-9Y for [email protected]; Fri, 30 Mar 2012 00:31:56 -0400 To: [email protected] Subject: Password Reset Request MIME-Version: 1.0 Content-type: text/html; charset=iso-8859-1 From: Sender Name <[email protected]> Message-Id: <[email protected]> Date: Fri, 30 Mar 2012 00:31:56 -0400 X-AntiAbuse: This header was added to track abuse, please include it with any abuse report X-AntiAbuse: Primary Hostname - server.domain1.com X-AntiAbuse: Original Domain - domain2.com X-AntiAbuse: Originator/Caller UID/GID - [507 504] / [47 12] X-AntiAbuse: Sender Address Domain - server.domain1.com

    Read the article

  • Looking for a new, free firewall (Sunbelt has a huge hole)

    - by Jason
    I've been using Sunbelt Personal Firewall v. 4.5 (previously Kerio). I've discovered that blocking Firefox connections in the configuration doesn't stop EXISTING Firefox connections. (See my post here yesterday http://superuser.com/questions/132625/sunbelt-firewall-4-5-wont-block-firefox) The "stop all traffic" may work on existing connections - but I'm done testing, as I need to be able to be selective, at any time. I was using the free version, so the "web filtering" option quit working after some time (mostly blocking ads and popups), but I didn't use that anyway. I used the last free version of Kerio before finally having to go to Sunbelt, because Kerio had an unfixed bug where you'd eventually get the BSOD and have to reset Kerio's configuration and start over (configure everything again). So I'm looking for a new Firewall. I don't like ZoneAlarm at all (no offense to all it's users that may be here - personal taste). I need the following: (Sunbelt has all these, except *) - 1. Be able to block in/out to localhost (trusted)/internet selectively for each application with a click (so there's 4 click boxes for each application) [*that effects everything immediately, regardless of what's already connected]. When a new application attempts a connection, you get an allow/deny/remember windows. - 2. Be able to easily set up filter rules for 'individual application'/'all applications,' by protocol, port/address (range), local, remote, in, out. [*Adding a filter rule also doesn't block existing connections in Sunbelt. That needs to work too.] - 3. Have an easy-to-get-to way to "stop all traffic" (like a right click option on the running icon in the task bar). - 4. Be able to set trusted/internet in/out block/allowed (4 things per item) for each of IGMP, ping, DNS, DHCP, VPN, and broadcasts. - 5. Define locahost as trusted/untrusted, define adapter connections as trusted/untrusted. - 6. Block incoming connetions during boot-up and shutdown. - 7. Show existing connections, including local & remote ip/port, protocol, current speed, total bytes transferred, and local ports opened for Listening. - 8. An Intrusion Prevention System which blocks (optionally select each one) known intrustions (long list). - 9. Block/allow applications from starting other applications (deny/allow/remember window). Wish list: A way of knowing what svchost.exe is doing - who is actually using it/calling it. I allowed it for localhost, and selectively allowed it for internet each time the allow/deny window came up. Thanks for any help/suggestions. (I'm using Windows XP SP3.)

    Read the article

  • Complete machine freezes...at a loss

    - by user28818
    Guys, We built around 12 machines a few months ago to run Ubuntu. They each have the following specs: ASUS Z8NA-D6 motherboard Dual quad core Intel(R) Xeon(R) CPU E5520 @ 2.27GHz OCZ Mod Extreme Pro 500W power supply 12 GB Kingston RAM Nvidia GeForce 9800 GT graphics card My machine ran well for awhile. However, it started experiencing random lockups. These lockups are not X lockups, they are complete system freezes. The nic stops responding, the magic sysrq buttons won't work. The machine is dead. I first suspected RAM. Memtest86 didn't find anything, but I replaced the RAM anyway. Still, lockups. So I replaced the graphics card. Still, more lockups. They became more and more frequent and started to happen 2-3 times a day. So I replaced the motherboard and power supply in one fell swoop. Suddenly, no more lockups! Woohoo! Except, a week later, in the morning, the machine wouldn't wake up. I reset it, started it up, and the log files showed the last entry at around 11 pm the evening before. This has started occurring with more frequency...now just about every morning I come in, the machine is locked up, and has been since the night before. Yesterday, in the 3 weeks since I replaced the motherboard and power supply, the machine actually locked up on in in mid-work. This is the first time since replacing the two (MB and PS) that this happened while I was using it. All others occurred while I was away. I'm at a loss. Nothing is in syslog or message that would indicate a problem around the time of the lockup. Temps are good...I use lmsensors to monitor and have a script that writes the output to file every minute. They never get that high. The only thing I haven't replaced at this point is the case and the harddrives. I doubt either could be the cause. What would you do if you were in my shoes? Is there a troubleshooting approach I'm missing? For the record, all of the other machines, all eleven of them, don't have any problems. They're all running the same version of Ubuntu (Lucid) that I am. Thanks!

    Read the article

  • How to remove RAID flag on unstriped drive without losing data?

    - by Alex Folland
    I have a Gigabyte Z68X-UD4-B3 motherboard. It advertises this new thing called "XHD", which is like RAID but makes a SSD and traditional-style drive work together to enable high speed with high capacity. I don't want to use this feature, and I already have Windows 7 64 installed without using this feature. When I first installed my 2 hard drives (1 SSD and 1 traditional-style drive) in my machine and booted it up for the first time, it ran a program from the mobo that asked me if I wanted to set up XHD. Thinking it would go to some config screen, I said yes. It immediately started doing something with my drives and finished. I considered that strange, but figured it wouldn't matter when I simply install Windows onto my SSD only. I now have my BIOS and Windows running in AHCI mode with no RAID arrays and separate drives. My SSD is one of those new Corsair Force GT drives which loses power every so often, causing Windows to BSOD. I've figured everything out about this problem, including installing the latest firmware from Corsair, and the only way to fix it at this point is by installing Intel Rapid Storage Technology to control AHCI instead of Windows, since the Windows AHCI driver disables the drive's power every once in a while and can't be configured not to do so. I've tried installing Intel Rapid Storage Technology. When I reboot my machine after doing so, it BSODs just after the Windows logo. I've figured out this is because my SSD and my traditional drive are flagged as RAID, as seen in the "Intel Matrix Storage Manager" program found by switching the BIOS hard drive handling to "RAID" mode. This is due to the XHD auto-config program I mentioned earlier. Normally, the BIOS is set to AHCI, and when the drives boot in AHCI mode, they work perfectly. So, I've concluded the data is stored in AHCI mode but the drives' flags are set to RAID. I've figured out that I can accomplish my objective by using the "Intel Matrix Storage Manager" program on the mobo (with "Reset disks to non-RAID"), but doing so would cause it to completely wipe the drives I select. I want to simply toggle these flags from RAID to AHCI so Intel Rapid Storage Technology doesn't fail and cause a BSOD upon booting, but without wiping the drives.

    Read the article

  • Can I use one virtualbox disk for multiple machines?

    - by mxp
    I'm not sure what search term to use and skimming through the VirtualBox manual didn't help me either, so I ask my two questions here... My setup is this: PC with dual boot into Windows 7 and a Debian operating system (both 64bit). I've created a virtual machine (Kubuntu, 64bit) under Windows and put it's VDI file on a SMB share of my NAS. Then I created a VM under linux using the same settings for memory etc and assigned the existing VDI file to it. My idea was that I could use that virtual machine from Windows and Linux as well. (1) Is this generally something that should work without problems? I noticed that snapshots get me into trouble because they appear to be not visible from the other operating system: The snapshots I took after installing the guest system are not visible under Linux. That's why I shut down the VM after usage and not save its state while it's running. My current problem is this: I have used the VM under Windows first, then under Linux. Now it will only start on Linux. When trying this on Windows the guest OS detects some kind of hard disk error and fails to boot because it cannot mount its drive. Obviously the virtual hard disk won't fail so it must have something to do with me using it under Linux. (2) How can I fix that? Update: It also looks like any changes I made in the VM under Linux have been reset by trying to boot it under Windows. Looks like it's back to the latest snapshot. I'm confused... Update The answer to my first question can be found below. In short: It works, as long as you don't use snapshots. The answer to my second question is this: Under Windows set the VM back to the latest snapshot and then discard the snapshot so it gets merged. There should be no snapshots left at the end. If you have multiple snapshots, discard the earliest ones first (Snapshot 1, then 2, 3, ...). I'm not sure what happens if you start at the end (.., 3, 2, 1). This of course leads to some data loss since you revert all changes since the last snapshot. But at least the VM is usable again.

    Read the article

  • Windows 8 disk errors

    - by wrongusername
    So yesterday, I forcibly restarted my Windows 8 PC. VMWare Workstation was having some trouble with the guest Linux Mint OS. It wasn't responding for some time, so I tried suspending it September 28th or perhaps even before. It wouldn't suspend -- I forgot what the window looked like, but all options in the power menu were disabled (i.e. "Shutdown," "Power Off," and options like that were all disabled). I eventually killed the VMWare application through Task Manager, though I was too lazy to hunt down the running virtual machine itself, and decided to kill it by just shutting down my PC entirely. The PC wouldn't shut down for quite some time after the monitor went blank, so I did a cold reset by holding the power button. I then powered it on again and Windows briefly gave me some message like "Search for KERNEL_STACK_INPAGE_ERROR." Windows then started diagnosing some problems and gave me the message, "Repairing disk errors. This might take over an hour to complete." That was yesterday night, and I went to sleep without waiting for it to finish. This morning, it said that the repair failed, and that the log was at C:\windows\system32\LogFiles\srt\srtTrail.txt (as I remember it -- I don't have the exact path I wrote down right now). It gave me some other options to troubleshoot, such as resetting Windows (files and settings still intact, but programs not installed through the app store will be erased). That didn't work (no error message given, I was just told it didn't work). I tried rebooting in safe mode, the same diagnosis process begins, except that this time it doesn't bother with the automatic repairs again. So I tried using the command prompt to try to see if my files are at least still there. I was on the X drive, and I couldn't cd to the C drive. I couldn't find my folder under Users (of course?), and couldn't find the srt folder under LogFiles either. I am not sure what to try next. I have backed up everything, but to the cloud, so if absolutely necessary I can start off with a fresh copy of Windows and restore all my data, though it would be a hassle. Any thoughts on what might be wrong or what I can try? My computer was purchased just this June, so the hard drive should still be pretty new.

    Read the article

  • What is the probable failure - no BSOD, no event log, monitors sleeping, force reboot required

    - by Tyler
    Every 3 to 15 days, my PC freezes. This typically happens when the computer is idle, I'm coming home from work, back from vacation, etc. It's never happened while using my computer. The monitors are in power save mode The Caps Lock light on the (wireless) keyboard doesn't work Ctrl-alt-del has no effect, mouse (wireless) has no effect The hardware reset button and single press of power putton have no effect Computer does not appear on the network No BSOD, no memory dump Event logs have no errors or indications of problems near the time of crash. Only messages after reboot indicating that there was a reboot without a clean shutdown. Windows is set to never put the computer to sleep (just the display) Here are the vital stats of the build: OS Windows 8 Pro 64-bit CPU Intel i5-2400 Mobo Intel BOXDP67DE Micro ATX GPU MSI N460GTX Cyclone768D5/OC RAM CORSAIR XMS3 8GB (2 x 4GB) CMX8GX3M2A1333C9 PSU SeaSonic X Series X650 Gold System Drive Samsung 840 Pro 256 GB SSD Data Drive 2 x Western Digital WD20EARS 2TB in hardware RAID 1 Optical Lite-On DVD burner IHAS424-98 And here is the story of how the problem developed and what I've done to diagnose: January 2011, system built with Windows 7 64-bit, runs great. March 2011, Intel replaced the mobo because of the bad sata controllers. October 2012, upgrade to Windows 8 (problems start shortly after). January 2013, system freezes and causes network to fail for the whole house. Unplug the network cable and other devices and PCs can use the internet. Plug it back in, internet goes away for everyone. Reboot and everything is fine. March 2013, install Intel Gigabit CT PCI-E NIC, disable mobo nic in bios. Network strangeness goes away. Freezes are less frequent. Memtest shows no problems (20 passes). Early June 2013, replace Antec PSU with SeaSonic PSU. Mid June 2013, replace OCZ Vertex 2 SSD with Samsung SSD. Late June 2013, get frustrated and hope the community has some good ideas (I'm running out of budget to replace parts). My next plan of attack is setting "Turn off display" to Never and using a screen saver to see how that reacts on the next freeze. It makes me sad to waste power for up to 15 days though. Has anyone out there seen a problem like this? Any ideas on what kind of malfunction would act this way? Ideas of other diagnostic steps to take?

    Read the article

  • IE9 Error: There was a pr?blem sending the command to the program

    - by HK1
    I'm working on a new/fresh Windows 7 32bit machine that now has IE9 installed. The user is using the Dell Stardock application as his primary "desktop" (all his links there). When we place an internet link there and click on it we get the following error message: There was a problem sending the command to the program. To me this indicates that IE9 is having trouble going to the website we want to go to, which should get passed as a parameter to the browser when it opens. I don't think this is a StarDock/ObjectDock problem because we also have some other problems with internet links. For example, we cannot move an internet link from the Desktop to the Quick Launch on the task bar. When we do try, it forces us to put the link with the IE icon as part of the IE menu instead of allowing us to have a shortcut there as it's own entry. I should mention however, that links on the desktop and in the taskbar do work as we expect them too (without showing the above error message). It appears that this problem started after installing Windows Updates. Since we installed a whole bunch of updates at once I have no idea which one caused the problem. I did have Google Chrome installed but I uninstalled it since the user wants to use IE. The problem started before I uninstalled Chrome. I also reset the browser settings on IE9. It didn't help. Next I uninstalled IE9 which took me back to IE8. This actually did resolve the problem but the problem came back as soon as I installed IE9 again. We have Verizon Internet Security installed. It's actually a McAfee product rebranded to look like Verizon. I'm not real crazy over this software but the customer has a subscription so we're not planning to change it. I have no reason to believe that this is causing the problem and yet I know that security software is often to blame for strange issues. I've looked at the registry settings for the following keys and everything appears to be ok for every single one of them: HKEY_CLASSES_ROOT\.htm HKEY_CLASSES_ROOT\.html HKEY_CLASSES_ROOT\http\shell\open\command HKEY_CLASSES_ROOT\http\shell\open\ddeexec\Application HKEY_CLASSES_ROOT\https\shell\open\command HKEY_CLASSES_ROOT\https\shell\open\ddeexec\Application HKEY_CLASSES_ROOT\htmlfile\shell\open\command HKEY_CLASSES_ROOT\Microsoft.Website\Shell\Open\Command Edit1: I've found two potential solutions but I won't be able to try them until tomorrow. One is to disable the "Windows Font Cache" service. Another is to clear IE cache and browsing history. I won't be able to try out either solution until tomorrow since this is a remote client's machine. I see there are lots of other suggestions online but if you take the time to read them through you'll see that the other suggestions didn't fix the problem.

    Read the article

  • Resetting root password on Fedora Core 3 - serial cable access only

    - by Sensible Eddie
    A little background: We have an old rackmount server running a customised version of Fedora, manufactured by a company called Navaho. The server is a TeamCAT, running some proprietary rubbish called Freedom2. We have to keep it going - the alternative is extraordinarily expensive, and the business is not likely to be running much longer to justify changing things. Through one means or another, it has fallen upon me to try and resolve our lack of root access. The previous admin has fallen under the proverbial bus, and nobody has any clue. We have no access to the root account for this server. ssh is running on the server, and there is one account admin that we can login with, however it has no permission to do anything (ironic...) The only other way into the server is with a null-modem serial cable. This works... up to a point. I can see the BIOS, I can see the post BIOS screen, and then I see "Starting grub", followed by another screen with about four lines of Linux information, but then it stops at that point. The server continues booting, and all services come online after around two minutes, but the serial terminal displays no more information. I understand it is possible to put Linux into "single user mode" to reset a root password, but I have no idea how to do this beyond trying to interrupt it at the grub stage listed above. When I have tried it just froze. It was almost like grub had appeared (since the server did not continue booting) but I couldn't see it on the serial terminal. Which made me think maybe the grub screen has some different serial settings? I don't know... it's the first time I've ever used serial for access! A friend of mine suggested trying to use a Fedora boot CD. We could boot from USB, so something along this approach is possible but again we still can only see what's going on with the serial terminal, so it might not be achievable. Does anyone have any suggestions for things I can try? I appreciate this is a bit of a long shot, but any assistance would be invaluable. *UPDATE 1 - 28/8/12 * - we will be making some attempts on this today and will post further details later!

    Read the article

  • My new hard drive doesn't have rights on my old one?

    - by Allan
    Until recently I had a 1 TB hard disk with Windows 7 on it, I have bought myself a SSD, removed the old harddisc and installed Windows 7 on my new one. After that I put back the old hard disk, and formatted it, now I could use that as backup and to keep files on. Nice, right? Well I was updating .Net framework through Windows update, when it stalled. I noticed some space was used on one of the drives on my secondary 'previously primary' hard disk. Apparently it was the .Net framework, trying to save some temporary files on my secondary disc, because it was the one with the most space. It was like it didn't get access. I cancled the installation and rebooted the computer. Now wanting to remove the temporary folder on my secondary harddisk. It told me. "You don't have access by SYSTEM", I don't understand, my user is administrator, its the only user there is and at the same time I can remove and delete any other folder on that drive. I'm gonna go a little pseudo here. But it feels as if the computer treats the old harddisk as protected from tampering by the new SSD. Also, I feel I should mention, they are both listed as primary, ... primary 0 and primary 1. Both using SATA cable. My old hard drive was partioned into 3 drives. 2 of them said the current owner was 'Administrator/myPCname' and the third one said the current owner was 'SYSTEM' I changed them all into the only one that I could pick from the list, which is my user since the 'Administrators/myPCname' wasn't exactly wrong.. could it be that they were somehow still attached to the old OS?.. the fact is I named my computer the exact same thing as it was called before installing a new windows.. so I can't really tell if its an old ownership or not. Also.. I'm currently logged in as 'myname' and I'm administrator.. now trying to delete the previously mentioned files.. it says 'you need access from 'myname' – and it can't delete.. That seems really messed up, I mean I'm logged in as the name it wants me to use. Is there maybe someway I could reset all the users on my computer? Or create some default? I don't know – I just want it to take a form I have always known, from a standard Windows point of view.

    Read the article

  • Wireless Network suddenly cant connect after Windows update

    - by vinir
    UPDATE: As my patience started to end, the laptop started to display symptoms of other malfunctions, so I ended up returning it to Asus and actually had the price of the laptop back in store credit. I did not solve the problem per se, but as I don't have the notebook and the screen, the keyboard, the touchpad and other parts were malfunctioning, I can safely assume that it was put to rest. I don't know how to behave when my question isn't actually answered, but was "solved", so I placed this over here. Anyone that knows how to end this topic, I would appreciate the heads up. Thanks for everything, everyone, it's nice to see that this topic in the community was active even when all this time had passed. vinir So I bought an ASUS K43E notebook earlier this year and built a wireless conection to link it to. It worked great for the first weeks, but then I updated my Windows 7 Home Basic with the daily updates; After that my home network couldn't be reached no matter what I did. I have linux on dual boot on the same notebook and it can connect to my home wireless network flawlessly. I have a hunch that it's somehow related to the Network Profile settings. I have noticed my network was set as "Home network", but after the system updates I got changed to "Public". Now I can't connect to it to change the profile settings. My Atheros Network adapter is updated to the latest driver (march 2012), and I still can't connect. The funny thing is that the same thing happened to my mother's notebook, as it has the same Network Adapter, Atheros AR9285, as I recall it. I managed to fix it on my mother's computer by using an specific network LSP and profiling reset that was available through her notebook's antivirus program, avast! Internet Security. I can't get that to work on my notebook, but I suspect that some related tool might just make it work too. So the question is: how to modify a network's profile and settings that were stored in my notebook? I can't connect to the specific network on Windows, as stated before.

    Read the article

  • Windows 7 booting and startup repair issues

    - by aardvark
    I have a MSI FR720 laptop with Windows 7 and Lubuntu partions. For quite a while (6 months or so) I've been having issues booting from my hard drive, it'd take me between 5 minutes and several hours for me to be able to have it recognize the hard drive as a bootable device. I did several disk checks on it, and my hard drive seems in perfect condition, and the fact that booting would usually only work after removing the hard drive and trying to reset it in its slot or lightly shaking it makes me think it had something to do with the connection in the hard drive slot as opposed to the hard drive itself. I was having particular issues with it detecting the hard drive today so I decided to try booting it from an external hard drive dock. It detected it first try and so far has had no problems finding the bootable partitions on my hard drive. When I selected my Windows 7 partition from the boot menu it said that it hadn't been shut down properly last time and needed startup repair. I've done this several times over the last 6 months, so this is hardly unusual. I do startup repair, it fails, and then I try to do a system restore. The system restore also failed, and it says that no files were changed. I restart and try it again. However, this time when I get to the startup repair it's not detecting a Windows OS. I tried clicking next and doing a startup repair but the repair is always failing. If I ignore the startup repair option and instead select "Launch windows normally" it will get to the windows animation, stop halfway through and then crash into a BSoD. I can't read the error on the screen because it immediately switches to back and tries to restart. This is my first time asking a question like this online, so let me know if I need to provide any extra information and I'll do my best to give it I tried using diskpart to find the list of partitions and see if one's labelled as an active partition, but it says that no disk were detected. I can run Lubuntu just fine. I can also see all of my Windows 7 files from it EDIT: The startup repair diagnosis and repair log is this: -- Number of repair attempts: 1 Session details System Disk = Windows directory = AutoChk Run = 0 Number of root causes = 1 Test Performed: Name: Check for updates Result: Completed successfully. Error code = 0x0 Time taken = 15ms Test Performed: Name: System disk test Result: Completed successfully. Error code = 0x0 Time taken = 31ms Root cause found. If a hard disk is installed, it is not responding. -- Any chance that this is a result of me doing this through an external dock through a USB drive?

    Read the article

  • Install XP Mode with VirtualBox Using the VMLite Plugin

    - by Mysticgeek
    Would you like to run XP Mode, but prefer Sun’s VirtualBox for virtualization?  Thanks to the free VMLite plugin, you can quickly and easily run XP Mode in or alongside VirtualBox. Yesterday we showed you one method to install XP Mode in VirtualBox, unfortunately in that situation you lose XP’s activation, and it isn’t possible to reactivate it. Today we show you a tried and true method for running XP mode in VirtualBox and integrating it seamlessly with Windows 7. Note: You need to have Windows 7 Professional or above to use XP Mode in this manner. Install XP Mode Make sure you’re logged in with Administrator rights for the entire process. The first thing you’ll want to do is install XP Mode on your system (link below). You don’t need to install Windows Virtual PC. Go through and install XP Mode using the defaults. Install VirtualBox Next you’ll need to install VirtualBox 3.1.2 or higher if it isn’t installed already. If you have an older version of VirtualBox installed, make sure to update it. During setup you’re notified that your network connection will be reset. Check the box next to Always trust software from “Sun Microsystems, Inc.” then click Install.   Setup only takes a couple of minutes, and does not require a reboot…which is always nice. Install VMLite XP Mode Plugin The next thing we’ll need to install is the VMLite XP Mode Plugin. Again Installation is simple following the install wizard. During the install like with VirtualBox you’ll be asked to install the device software. After it’s installed go to the Start menu and run VMLite Wizard as Administrator. Select the location of the XP Mode Package which by default should be in C:\Program Files\Windows XP Mode. Accept the EULA…and notice that it’s meant for Windows 7 Professional, Enterprise, and Ultimate editions. Next, name the machine, choose the install folder, and type in a password. Select if you want Automatic Updates turned on or not. Wait while the process completes then click Finish.   The VMLite XP Mode will set up to run the first time. That is all there is to this section. You can run XP Mode from within the VMLite Workstation right away. XP Mode is fully activated already, and the Guest Additions are already installed, so there’s nothing else you need to do!  XP Mode is the whole way ready to use. Integration with VirtualBox Since we installed the VMLite Plugin, when you open VirtualBox you’ll see it listed as one of your machines and you can start it up from here.   Here we see VMLite XP Mode running in Sun VirtualBox. Integrate with Windows 7 To integrate it with Windows 7 click on Machine \ Seamless Mode…   Here you can see the XP menu and Taskbar will be placed on top of Windows 7. From here you can access what you need from XP Mode.   Here we see XP running on Virtual Box in Seamless Mode. We have the old XP WordPad sitting next to the new Windows 7 version of WordPad. This works so seamlessly you forget if your working in XP or Windows 7. In this example we have Windows Home Server Console running in Windows 7, while installing MSE from IE 6 in XP Mode. At the top of the screen you will still have access to the VMs controls.   You can click the button to exit Seamless Mode, or simply hit the right “CTRL+L” Conclusion This is a very slick way to run XP Mode in VirtualBox on any machine that doesn’t have Hardware Virtualization. This method also doesn’t lose the XP Mode activation and is actually extremely easy to set up. If you prefer VMware (like we do), Check out how to run XP Mode on machines without Hardware Virtualization capability, and also how to create an XP Mode for Vista and Windows 7 Home Premium. Links Download XP Mode Download VirtualBox Download VMLite XP Mode Plugin for VirtualBox (Site Registration Required) Similar Articles Productive Geek Tips Search for Install Packages from the Ubuntu Command LineHow To Run XP Mode in VirtualBox on Windows 7 (sort of)Install and Use the VLC Media Player on Ubuntu LinuxInstall Monodevelop on Ubuntu LinuxInstall Flash Plugin Manually in Firefox on Vista TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Enable Check Box Selection in Windows 7 OnlineOCR – Free OCR Service Betting on the Blind Side, a Vanity Fair article 30 Minimal Logo Designs that Say More with Less LEGO Digital Designer – Free Create a Personal Website Quickly using Flavors.me

    Read the article

  • Install XP Mode with VirtualBox Using the VMLite Plugin

    - by Mysticgeek
    Would you like to run XP Mode, but prefer Sun’s VirtualBox for virtualization?  Thanks to the free VMLite plugin, you can quickly and easily run XP Mode in or alongside VirtualBox. Yesterday we showed you one method to install XP Mode in VirtualBox, unfortunately in that situation you lose XP’s activation, and it isn’t possible to reactivate it. Today we show you a tried and true method for running XP mode in VirtualBox and integrating it seamlessly with Windows 7. Note: You need to have Windows 7 Professional or above to use XP Mode in this manner. Install XP Mode Make sure you’re logged in with Administrator rights for the entire process. The first thing you’ll want to do is install XP Mode on your system (link below). You don’t need to install Windows Virtual PC. Go through and install XP Mode using the defaults. Install VirtualBox Next you’ll need to install VirtualBox 3.1.2 or higher if it isn’t installed already. If you have an older version of VirtualBox installed, make sure to update it. During setup you’re notified that your network connection will be reset. Check the box next to Always trust software from “Sun Microsystems, Inc.” then click Install.   Setup only takes a couple of minutes, and does not require a reboot…which is always nice. Install VMLite XP Mode Plugin The next thing we’ll need to install is the VMLite XP Mode Plugin. Again Installation is simple following the install wizard. During the install like with VirtualBox you’ll be asked to install the device software. After it’s installed go to the Start menu and run VMLite Wizard as Administrator. Select the location of the XP Mode Package which by default should be in C:\Program Files\Windows XP Mode. Accept the EULA…and notice that it’s meant for Windows 7 Professional, Enterprise, and Ultimate editions. Next, name the machine, choose the install folder, and type in a password. Select if you want Automatic Updates turned on or not. Wait while the process completes then click Finish.   The VMLite XP Mode will set up to run the first time. That is all there is to this section. You can run XP Mode from within the VMLite Workstation right away. XP Mode is fully activated already, and the Guest Additions are already installed, so there’s nothing else you need to do!  XP Mode is the whole way ready to use. Integration with VirtualBox Since we installed the VMLite Plugin, when you open VirtualBox you’ll see it listed as one of your machines and you can start it up from here.   Here we see VMLite XP Mode running in Sun VirtualBox. Integrate with Windows 7 To integrate it with Windows 7 click on Machine \ Seamless Mode…   Here you can see the XP menu and Taskbar will be placed on top of Windows 7. From here you can access what you need from XP Mode.   Here we see XP running on Virtual Box in Seamless Mode. We have the old XP WordPad sitting next to the new Windows 7 version of WordPad. This works so seamlessly you forget if your working in XP or Windows 7. In this example we have Windows Home Server Console running in Windows 7, while installing MSE from IE 6 in XP Mode. At the top of the screen you will still have access to the VMs controls.   You can click the button to exit Seamless Mode, or simply hit the right “CTRL+L” Conclusion This is a very slick way to run XP Mode in VirtualBox on any machine that doesn’t have Hardware Virtualization. This method also doesn’t lose the XP Mode activation and is actually extremely easy to set up. If you prefer VMware (like we do), Check out how to run XP Mode on machines without Hardware Virtualization capability, and also how to create an XP Mode for Vista and Windows 7 Home Premium. Links Download XP Mode Download VirtualBox Download VMLite XP Mode Plugin for VirtualBox (Site Registration Required) Similar Articles Productive Geek Tips Search for Install Packages from the Ubuntu Command LineHow To Run XP Mode in VirtualBox on Windows 7 (sort of)Install and Use the VLC Media Player on Ubuntu LinuxInstall Monodevelop on Ubuntu LinuxInstall Flash Plugin Manually in Firefox on Vista TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Enable Check Box Selection in Windows 7 OnlineOCR – Free OCR Service Betting on the Blind Side, a Vanity Fair article 30 Minimal Logo Designs that Say More with Less LEGO Digital Designer – Free Create a Personal Website Quickly using Flavors.me

    Read the article

  • AGENT: The World's Smartest Watch

    - by Rob Chartier
    AGENT: The World's Smartest Watch by Secret Labs + House of Horology Disclaimer: Most if not all of this content has been gleaned from the comments on the Kickstarter project page and comments section. Any discrepancies between this post and any documentation on agentwatches.com, kickstarter.com, etc.., those official sites take precedence. Overview The next generation smartwatch with brand-new technology. World-class developer tools, unparalleled battery life, Qi wireless charging. Kickstarter Page, Comments Funding period : May 21, 2013 - Jun 20, 2013 MSRP : $249 Other Urls http://www.agentwatches.com/ https://www.facebook.com/agentwatches http://twitter.com/agentwatches http://pinterest.com/agentwatches/ http://paper.li/robchartier/1371234640 Developer Story The first official launch of the preview SDK and emulator will happen on 20-Jun-2013.  All development will be done in Visual Studio 2012, using the .NET Micro Framework SDK 2.3.  The SDK will ship with the first round of the expected API for developers along with an emulator. With that said, there is no need to wait for the SDK.  You can download the tooling now and get started with Apps and Faces immediately.  The only thing that you will not be able to work with is the API; but for example, watch faces, you can start building the basic face rendering with the Bitmap graphics drawing in the .NET Micro Framework.   Does it look good? Before we dig into any more of the gory details, here are a few photos of the current available prototype models.   The watch on the tiny QI Charter   If you wander too far away from your phone, your watch will let you know with a vibration and a message, all but one button will dismiss the message.   An app showing the premium weather data!   Nice stitching on the straps, leather and silicon will be available, along with a few lengths to choose from (short, regular, long lengths). On to those gory details…. Hardware Specs Processor 120MHz ARM Cortex-M4 processor (ATSAM4SD32) with secondary AVR co-processor Flash & RAM 2MB of onboard flash and 160KB of RAM 1/4 of the onboard flash will be used by the OS The flash is permanent (non-volatile) storage. Bluetooth Bluetooth 4.0 BD/EDR + LE Bluetooth 4.0 is backwards compatible with Bluetooth 2.1, so classic Bluetooth functions (BD/EDR, SPP/AVRCP/PBAP/etc.) will work fine. Sensors 3D Accelerometer (Motion) ST LSM303DLHC Ambient Light Sensor Hardware power metering Vibration Motor (You can pulse it to create vibration patterns, not sure about the vibration strength - driven with PWM) No piezo/speaker or microphone. Other QI Wireless Charging, no NFC, no wall adapter included Custom LED Backlight No GPS in the watch. It uses the GPS in your phone. AGENT watch apps are deployed and debugged wirelessly from your PC via Bluetooth. RoHS, Pb-free Battery Expected to use a CR2430-sized rechargeable battery – replaceable (Mouser, Amazon) Estimated charging time from empty is 2 hours with provided charger 7 Days typical with Bluetooth on, 30 days with Bluetooth off (watch-face only mode) The battery should last at least 2 years, with 100s of charge cycles. Physical dimensions Roughly 38mm top-to-bottom on the front face 35mm left-to-right on the front face and around 12mm in depth 22mm strap Two ~1/16" hex screws to attach the watch pin The top watchcase material candidates are PVD stainless steel, brushed matte ceramic, and high-quality polycarbonate (TBD). The glass lens is mineral glass, Anti-glare glass lens Strap options Leather and silicon straps will be available Expected to have three sizes Display 1.28" Sharp Memory Display The display stays on 100% of the time. Dimensions: 128x128 pixels Buttons Custom "Pusher" buttons, they will not make noise like a mouse click, and are very durable. The top-left button activates the backlight; bottom-left changes apps; three buttons on the right are up/select/down and can be used for custom purposes by apps. Backup reset procedure is currently activated by holding the home/menu button and the top-right user button for about ten seconds Device Support Android 2.3 or newer iPhone 4S or newer Windows Phone 8 or newer Heart Rate monitors - Bluetooth SPP or Bluetooth LE (GATT) is what you'll want the heart monitor to support. Almost limitless Bluetooth device support! Internationalization & Localization Full UTF8 Support from the ground up. AGENT's user interface is in English. Your content (caller ID, music tracks, notifications) will be in your native language. We have a plan to cover most major character sets, with Latin characters pre-loaded on the watch. Simplified Chinese will be available Feature overview Phone lost alert Caller ID Music Control (possible volume control) Wireless Charging Timer Stopwatch Vibrating Alarm (possibly custom vibrations for caller id) A few default watch faces Airplane mode (by demand or low power) Can be turned off completely Customizable 3rd party watch faces, applications which can be loaded over bluetooth. Sample apps that maybe installed Weather Sample Apps not installed Exercise App Other Possible Skype integration over Bluetooth. They will provide an AGENT app for your smartphone (iPhone, Android, Windows Phone). You'll be able to use it to load apps onto the watch.. You will be able to cancel phone calls. With compatible phones you can also answer, end, etc. They are adopting the standard hands-free profile to provide these features and caller ID.

    Read the article

  • Secure wipe of a hard drive using WinPE.

    - by Derek Meier
    Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin;} The wiping of a hard drive is typically seen as fairly trivial.  There are tons of applications out there that will do it for you.  Point àClickàGlobal-Thermo Nuclear War. However, these applications are typically expensive or unreliable.  Plus, if you have a laptop or lack a secondary computer to put the hard drive into – how on earth do you wipe it quickly and easily while still conforming to a 7 pass rule (this means that every possible bit on the hard drive is set to 0 and then to 1 seven times in a row)?  Yes, one pass should be enough – as turning every bit from a 1 to a zero will wipe the data from existence.  But, we’re dealing with tinfoil hat wearing types here people.  DOD standards dictate at least 3 passes, and typically 7 is the preferred amount.  I’m not going to argue about data recovery.  I have been told to use 7 passes, and so I will.  So say we all! Quite some time ago I used to make a BartPE XP-based boot cd for the original purpose of securely wiping data.  I loved BartPE and integrated so many plugins into my builds that I could do pretty much anything directly from CD.  Reset passwords, uninstall security updates, wipe drives, chkdsk, remove spyware, install Windows, etc.  However, with the newer multi-core systems and new chipsets coming out from vendors, I found that BartPE was rather difficult to keep up to date.  I have since switched to WinPE 3.0 (Windows Preinstallation Environment). http://technet.microsoft.com/en-us/library/cc748933(WS.10).aspx  It is fairly simple to create your own CD, and I have made a few helpful scripts to easily integrate drivers and rebuild the ISO file for you.  I’ll cover making your own boot CD utilizing WinPE 3.0 in a later post – I can talk about WinPE forever and need to collect my thoughts!!  My wife loves talking about WinPE almost as much as talking about Doctor Who.  Wait, did I say loves?  Hmmmm, I may have meant loathes. The topic at hand?  Right. Wiping a drive! I must have drunk too much coffee this morning.  I like to use a simple batch script that calls a combination of diskpart.exe from Microsoft® and Sdelete.exe created by our friend Mark Russinovich. http://technet.microsoft.com/en-us/sysinternals/bb897443.aspx All of the following files are located within the same directory on my WinPE boot CD. Here are the contents of wipe_me.bat, script.txt and sdelete.reg. Wipe_me.bat:   @echo off echo. echo     I will completely wipe the local hard drives using echo     7 individual wipes. The data will NOT echo     be recoverable.  I will begin after you pause echo. echo Preparing to partition and format disk. Diskpart.exe /s "script.txt" REM I was annoyed by not having a completely automated script – and Sdelete wants you to accept the license agreement. So, I added a registry file to skip doing that. regedit /S sdelete.reg rem sdelete options selected are: -p (passes) -c (zero free space) -s (recurse through subdirectories, if any) -z (clean free space) [drive letter] sdelete.exe -p 7 -c -s -z c: echo. echo Pass seven complete. echo. echo Wiping complete. Pause exit script.txt: list disk select disk 0 clean create partition primary select partition 1 active format FS=NTFS LABEL="New Volume" QUICK assign letter=c exit *Notes: This script assumes one local hard drive – change the script as you see fit for your environment.  The clean command will overwrite the master boot record and any hidden sector information – so be careful!   sdelete.reg: Windows Registry Editor Version 5.00 [HKEY_CURRENT_USER\Software\Sysinternals\SDelete] "EulaAccepted"=dword:00000001   With a combination of WinPE, sdelete.exe and your friendly neighborhood text editor you can begin wiping drives as quickly and easily as possible!  I hope this helps, I get asked this a lot in my line of work. Best of luck, Derek

    Read the article

  • Change the User Interface Language in Ubuntu

    - by Matthew Guay
    Would you like to use your Ubuntu computer in another language?  Here’s how you can easily change your interface language in Ubuntu. Ubuntu’s default install only includes a couple languages, but it makes it easy to find and add a new interface language to your computer.  To get started, open the System menu, select Administration, and then click Language Support. Ubuntu may ask if you want to update or add components to your current default language when you first open the dialog.  Click Install to go ahead and install the additional components, or you can click Remind Me Later to wait as these will be installed automatically when you add a new language. Now we’re ready to find and add an interface language to Ubuntu.  Click Install / Remove Languages to add the language you want. Find the language you want in the list, and click the check box to install it.  Ubuntu will show you all the components it will install for the language; this often includes spellchecking files for OpenOffice as well.  Once you’ve made your selection, click Apply Changes to install your new language.  Make sure you’re connected to the internet, as Ubuntu will have to download the additional components you’ve selected. Enter your system password when prompted, and then Ubuntu will download the needed languages files and install them.   Back in the main Language & Text dialog, we’re now ready to set our new language as default.  Find your new language in the list, and then click and drag it to the top of the list. Notice that Thai is the first language listed, and English is the second.  This will make Thai the default language for menus and windows in this account.  The tooltip reminds us that this setting does not effect system settings like currency or date formats. To change these, select the Text Tab and pick your new language from the drop-down menu.  You can preview the changes in the bottom Example box. The changes we just made will only affect this user account; the login screen and startup will not be affected.  If you wish to change the language in the startup and login screens also, click Apply System-Wide in both dialogs.  Other user accounts will still retain their original language settings; if you wish to change them, you must do it from those accounts. Once you have your new language settings all set, you’ll need to log out of your account and log back in to see your new interface language.  When you re-login, Ubuntu may ask you if you want to update your user folders’ names to your new language.  For example, here Ubuntu is asking if we want to change our folders to their Thai equivalents.  If you wish to do so, click Update or its equivalents in your language. Now your interface will be almost completely translated into your new language.  As you can see here, applications with generic names are translated to Thai but ones with specific names like Shutter keep their original name. Even the help dialogs are translated, which makes it easy for users around to world to get started with Ubuntu.  Once again, you may notice some things that are still in English, but almost everything is translated. Adding a new interface language doesn’t add the new language to your keyboard, so you’ll still need to set that up.  Check out our article on adding languages to your keyboard to get this setup. If you wish to revert to your original language or switch to another new language, simply repeat the above steps, this time dragging your original or new language to the top instead of the one you chose previously. Conclusion Ubuntu has a large number of supported interface languages to make it user-friendly to people around the globe.  And since you can set the language for each user account, it’s easy for multi-lingual individuals to share the same computer. Or, if you’re using Windows, check out our article on how you can Change the User Interface Language in Vista or Windows 7, too! Similar Articles Productive Geek Tips Restart the Ubuntu Gnome User Interface QuicklyChange the User Interface Language in Vista or Windows 7Create a Samba User on UbuntuInstall Samba Server on UbuntuSee Which Groups Your Linux User Belongs To TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips VMware Workstation 7 Acronis Online Backup DVDFab 6 Revo Uninstaller Pro FetchMp3 Can Download Videos & Convert Them to Mp3 Use Flixtime To Create Video Slideshows Creating a Password Reset Disk in Windows Bypass Waiting Time On Customer Service Calls With Lucyphone MELTUP – "The Beginning Of US Currency Crisis And Hyperinflation" Enable or Disable the Task Manager Using TaskMgrED

    Read the article

  • Linux-Containers — Part 1: Overview

    - by Lenz Grimmer
    "Containers" by Jean-Pierre Martineau (CC BY-NC-SA 2.0). Linux Containers (LXC) provide a means to isolate individual services or applications as well as of a complete Linux operating system from other services running on the same host. To accomplish this, each container gets its own directory structure, network devices, IP addresses and process table. The processes running in other containers or the host system are not visible from inside a container. Additionally, Linux Containers allow for fine granular control of resources like RAM, CPU or disk I/O. Generally speaking, Linux Containers use a completely different approach than "classicial" virtualization technologies like KVM or Xen (on which Oracle VM Server for x86 is based on). An application running inside a container will be executed directly on the operating system kernel of the host system, shielded from all other running processes in a sandbox-like environment. This allows a very direct and fair distribution of CPU and I/O-resources. Linux containers can offer the best possible performance and several possibilities for managing and sharing the resources available. Similar to Containers (or Zones) on Oracle Solaris or FreeBSD jails, the same kernel version runs on the host as well as in the containers; it is not possible to run different Linux kernel versions or other operating systems like Microsoft Windows or Oracle Solaris for x86 inside a container. However, it is possible to run different Linux distribution versions (e.g. Fedora Linux in a container on top of an Oracle Linux host), provided it supports the version of the Linux kernel that runs on the host. This approach has one caveat, though - if any of the containers causes a kernel crash, it will bring down all other containers (and the host system) as well. For example, Oracle's Unbreakable Enterprise Kernel Release 2 (2.6.39) is supported for both Oracle Linux 5 and 6. This makes it possible to run Oracle Linux 5 and 6 container instances on top of an Oracle Linux 6 system. Since Linux Containers are fully implemented on the OS level (the Linux kernel), they can be easily combined with other virtualization technologies. It's certainly possible to set up Linux containers within a virtualized Linux instance that runs inside Oracle VM Server for Oracle VM Virtualbox. Some use cases for Linux Containers include: Consolidation of multiple separate Linux systems on one server: instances of Linux systems that are not performance-critical or only see sporadic use (e.g. a fax or print server or intranet services) do not necessarily need a dedicated server for their operations. These can easily be consolidated to run inside containers on a single server, to preserve energy and rack space. Running multiple instances of an application in parallel, e.g. for different users or customers. Each user receives his "own" application instance, with a defined level of service/performance. This prevents that one user's application could hog the entire system and ensures, that each user only has access to his own data set. It also helps to save main memory — if multiple instances of a same process are running, the Linux kernel can share memory pages that are identical and unchanged across all application instances. This also applies to shared libraries that applications may use, they are generally held in memory once and mapped to multiple processes. Quickly creating sandbox environments for development and testing purposes: containers that have been created and configured once can be archived as templates and can be duplicated (cloned) instantly on demand. After finishing the activity, the clone can safely be discarded. This allows to provide repeatable software builds and test environments, because the system will always be reset to its initial state for each run. Linux Containers also boot significantly faster than "classic" virtual machines, which can save a lot of time when running frequent build or test runs on applications. Safe execution of an individual application: if an application running inside a container has been compromised because of a security vulnerability, the host system and other containers remain unaffected. The potential damage can be minimized, analyzed and resolved directly from the host system. Note: Linux Containers on Oracle Linux 6 with the Unbreakable Enterprise Kernel Release 2 (2.6.39) are still marked as Technology Preview - their use is only recommended for testing and evaluation purposes. The Open-Source project "Linux Containers" (LXC) is driving the development of the technology behind this, which is based on the "Control Groups" (CGroups) and "Name Spaces" functionality of the Linux kernel. Oracle is actively involved in the Linux Containers development and contributes patches to the upstream LXC code base. Control Groups provide means to manage and monitor the allocation of resources for individual processes or process groups. Among other things, you can restrict the maximum amount of memory, CPU cycles as well as the disk and network throughput (in MB/s or IOP/s) that are available for an application. Name Spaces help to isolate process groups from each other, e.g. the visibility of other running processes or the exclusive access to a network device. It's also possible to restrict a process group's access and visibility of the entire file system hierarchy (similar to a classic "chroot" environment). CGroups and Name Spaces provide the foundation on which Linux containers are based on, but they can actually be used independently as well. A more detailed description of how Linux Containers can be created and managed on Oracle Linux will be explained in the second part of this article. Additional links related to Linux Containers: OTN Article: The Role of Oracle Solaris Zones and Linux Containers in a Virtualization Strategy Linux Containers on Wikipedia - Lenz Grimmer Follow me on: Personal Blog | Facebook | Twitter | Linux Blog |

    Read the article

  • Diagnose PC Hardware Problems with an Ubuntu Live CD

    - by Trevor Bekolay
    So your PC randomly shuts down or gives you the blue screen of death, but you can’t figure out what’s wrong. The problem could be bad memory or hardware related, and thankfully the Ubuntu Live CD has some tools to help you figure it out. Test your RAM with memtest86+ RAM problems are difficult to diagnose—they can range from annoying program crashes, or crippling reboot loops. Even if you’re not having problems, when you install new RAM it’s a good idea to thoroughly test it. The Ubuntu Live CD includes a tool called Memtest86+ that will do just that—test your computer’s RAM! Unlike many of the Live CD tools that we’ve looked at so far, Memtest86+ has to be run outside of a graphical Ubuntu session. Fortunately, it only takes a few keystrokes. Note: If you used UNetbootin to create an Ubuntu flash drive, then memtest86+ will not be available. We recommend using the Universal USB Installer from Pendrivelinux instead (persistence is possible with Universal USB Installer, but not mandatory). Boot up your computer with a Ubuntu Live CD or USB drive. You will be greeted with this screen: Use the down arrow key to select the Test memory option and hit Enter. Memtest86+ will immediately start testing your RAM. If you suspect that a certain part of memory is the problem, you can select certain portions of memory by pressing “c” and changing that option. You can also select specific tests to run. However, the default settings of Memtest86+ will exhaustively test your memory, so we recommend leaving the settings alone. Memtest86+ will run a variety of tests that can take some time to complete, so start it running before you go to bed to give it adequate time. Test your CPU with cpuburn Random shutdowns – especially when doing computationally intensive tasks – can be a sign of a faulty CPU, power supply, or cooling system. A utility called cpuburn can help you determine if one of these pieces of hardware is the problem. Note: cpuburn is designed to stress test your computer – it will run it fast and cause the CPU to heat up, which may exacerbate small problems that otherwise would be minor. It is a powerful diagnostic tool, but should be used with caution. Boot up your computer with a Ubuntu Live CD or USB drive, and choose to run Ubuntu from the CD or USB drive. When the desktop environment loads up, open the Synaptic Package Manager by clicking on the System menu in the top-left of the screen, then selecting Administration, and then Synaptic Package Manager. Cpuburn is in the universe repository. To enable the universe repository, click on Settings in the menu at the top, and then Repositories. Add a checkmark in the box labeled “Community-maintained Open Source software (universe)”. Click close. In the main Synaptic window, click the Reload button. After the package list has reloaded and the search index has been rebuilt, enter “cpuburn” in the Quick search text box. Click the checkbox in the left column, and select Mark for Installation. Click the Apply button near the top of the window. As cpuburn installs, it will caution you about the possible dangers of its use. Assuming you wish to take the risk (and if your computer is randomly restarting constantly, it’s probably worth it), open a terminal window by clicking on the Applications menu in the top-left of the screen and then selection Applications > Terminal. Cpuburn includes a number of tools to test different types of CPUs. If your CPU is more than six years old, see the full list; for modern AMD CPUs, use the terminal command burnK7 and for modern Intel processors, use the terminal command burnP6 Our processor is an Intel, so we ran burnP6. Once it started up, it immediately pushed the CPU up to 99.7% total usage, according to the Linux utility “top”. If your computer is having a CPU, power supply, or cooling problem, then your computer is likely to shutdown within ten or fifteen minutes. Because of the strain this program puts on your computer, we don’t recommend leaving it running overnight – if there’s a problem, it should crop up relatively quickly. Cpuburn’s tools, including burnP6, have no interface; once they start running, they will start driving your CPU until you stop them. To stop a program like burnP6, press Ctrl+C in the terminal window that is running the program. Conclusion The Ubuntu Live CD provides two great testing tools to diagnose a tricky computer problem, or to stress test a new computer. While they are advanced tools that should be used with caution, they’re extremely useful and easy enough that anyone can use them. Similar Articles Productive Geek Tips Reset Your Ubuntu Password Easily from the Live CDCreate a Persistent Bootable Ubuntu USB Flash DriveAdding extra Repositories on UbuntuHow to Share folders with your Ubuntu Virtual Machine (guest)Building a New Computer – Part 3: Setting it Up TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips DVDFab 6 Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 Have Fun Editing Photo Editing with Citrify Outlook Connector Upgrade Error Gadfly is a cool Twitter/Silverlight app Enable DreamScene in Windows 7 Microsoft’s “How Do I ?” Videos Home Networks – How do they look like & the problems they cause

    Read the article

< Previous Page | 116 117 118 119 120 121 122 123 124 125 126 127  | Next Page >