Search Results

Search found 10300 results on 412 pages for 'apache httpcomponents'.

Page 121/412 | < Previous Page | 117 118 119 120 121 122 123 124 125 126 127 128  | Next Page >

• WAMP: Apache refusing connections outside the network

  - by JoeWolf

  I have wamp installed. I ran the server, everything is running fine from localhost and my local ip address. I forwarded port 80 on my router. Whenever I try to access the server from the outside, using my real ip, it doesn't work and timeouts. I though port forwarding is not working, forwarded another port for different service and it went through, so the problem is with apache. I checked the error log, didn't find any errors. Skype is off. Any tips what could be causing this? Thanks!

  Read the article

• IfModule itk.c ignored even if I'm running Apache itk

  - by djechelon

  I'm running itk as Apache MPM. In order to prevent error in case I need to change the MPM in the future, I set <IfModule itk.c> AssignUserID user group </IfModule> but I found that it gets ignored. In fact, if I add a WTF like and run rcapache2 configtest it returns me Syntax OK <IfModule itk.c> AssignUserID user group WTF ##doesn't throw error </IfModule> By the way, /etc/sysconfig/apache2 shows APACHE_MPM="itk" How do I check if I'm running itk or not?

  Read the article

• Where i can get Binary for Apache http server 2.2.15 for solaris

  - by user201966

  I need to install apache http server 2.2.15 in solaris 9 .But in apache site ,only source is available for solaris. Please help me to find binary distribution for solaris 9? If i have to compile the source to binary for solaris,tell me how to compile the source for solaris 9?

  Read the article

• Apache: multiple domains handling

  - by cache

  So I use following schema to handle multiple sites on my apache: <VirtualHost 192.168.1.100:80> # get the server name from the Host: header UseCanonicalName Off VirtualDocumentRoot /var/www/%0/docs VirtualScriptAlias /var/www/%0/cgi-bin </VirtualHost> Therefore, if a client go to www.example.com, it will actually point to /var/www/www.example.com/doc/, which is good. However, what if the client go to example.com? It will point to /var/www/example.com/doc, which is not what we want. So my question is: is there any better schema for that? Or what should I do to fix the issue? Thanks!

  Read the article

• Apache 2.4 subdomain setup fails

  - by Grashopper

  I am struggling with this all the day, no answer i found here as well. Please advice how to setup proper a subdomain i need. My Apache config has 2 domains configured (on same IP), for the domain2.com i need to setup a sub-domain. Here is what i have so far, but the subdomain keeps redirecting me to domain2.com (main site). <VirtualHost 11.11.11.11:80> ServerName domain1.com ServerAlias domain1.com *.domain1.com DocumentRoot "C:/wwwmap/domain1.com" </VirtualHost> <VirtualHost 11.11.11.11:80> ServerName domain2.com ServerAlias domain2.com *.domain2.com DocumentRoot "C:/wwwmap/domain2.com" </VirtualHost> <VirtualHost 46.4.24.4:80> ServerName projects.domain2.com DocumentRoot "C:/wwwmap/projects" </VirtualHost> The DNS entry is: projects in CNAME domain2.com Trying to remove ServerAlias domain2.com *.domain2.com worked so far, but then domain2.com is redirecting to domain1.com What am i doing wrong?

  Read the article

• Apache server, PHP

  - by user65649

  I am running a php site on my apache server (Mac). I am having trouble displaying images on the site when I access it externally or from another computer on the same server. If I try to access the image directly. website.com/image.jpg I get a broken link icon and can't display the image. Any ideas what could cause this? My images are embedded using a style.css file. background-image:url(image.jpg);

  Read the article

• mod_perl loses STDOUT in middle of request

  - by puzzled72

  Hi, I have been having this weird issue where mod_perl seems to lose STDOUT in the middle of the request. So far I have eliminated everything I could think of. You might have seen this bug related to the following errors in error_log : Apache2 IO flush: (103) Apache2::RequestIO::read: (104) Software caused connection abort They are all the same error. It happens when the perl script running under mod_perl loses STDOUT when trying to print the result back to apache. I only notice this error on my servers running the following: (centos5.4) Perl 5.8.8-27 mod_perl 2.0.4-6 httpd 2.2.3-31 kernel-2.6.18-164.15.1 It's not the code This code has been working for months It's not network related The browser gets the error response from apache. It's not time related I get the error 15 or so seconds after I restart httpd It's not idle httpd related I have tried reducing the min/max SpareServers to 1 It's not load related I get the error even if there are only 10 sessions on httpd It's not related to the "fd < PERLIO_MAX_REFCOUNTABLE_FD" perl 5.8.8 bug I recompiled perl-5.8.8 with the patch mentioned here : https://bugzilla.redhat.com/show_bug.cgi?id=559832, same error. It appeared sometime between December 2009 and February 2010 sorry I cannot be more specific Anyone has any idea ? Anything that I have not tested ? Really Puzzled!

  Read the article

• Subversion gives Error 500 until authenticating with a web browser

  - by Farseeker

  We used to use Collabnet SVN/Apache combo on a Windows server with LDAP authentication, and whilst the performance wasn't brilliant it used to work perfectly. After switching to a fresh Ubuntu 10 install, and setting up an Apache/SVN/LDAP configuration, we have HTTPS access to our repositories, using Active Directory authentication via LDAP. We're now having a very peculiar issue. Whenever a new user accesses a repository, our SVN clients (we have a few depending on the tool, but for arguments sake, let's stick to Tortoise SVN) report "Error 500 - Unknown Response". To get around this, we have to log into the repo using a web browser and navigate 'backwards' until it works E.G: SVN Checkout https://svn.example.local/SVN/MyRepo/MyModule/ - Error 500 (bad) Webbrowse to https://svn.example.local/SVN/MyRepo/MyModule/ - Error 500 (bad) Webbrowse to https://svn.example.local/SVN/MyRepo/ - Error 500 (bad) Webbrowse to https://svn.example.local/SVN/ - Forbidden 403 (correct) Webbrowse to https://svn.example.local/SVN/MyRepo/ - OK 200 (correct) SVN Checkout https://svn.example.local/SVN/MyRepo/MyModule/ - Error 500 (bad) Webbrowse to https://svn.example.local/SVN/MyRepo/MyModule/ - OK 200 (correct) SVN Checkout https://svn.example.local/SVN/MyRepo/MyModule/ - OK 200 (correct) It seems to require authentication up the tree, starting from the svnparentpath up through to the module required. Has anyone seen anything like this before? Any ideas on where to start before I ditch it back to Collabnet's SVN server?

  Read the article

• Apache2 Enabling Includes module causes svn access to quit working

  - by Matthew Talbert

  I have dav_svn installed to provide http access to my svn repos. The url is directly under root, eg mywebsite.com/svn/individual-repo. This setup has been working great for some time. Now, I need SSI (server-side includes) for a project, so I enabled this module with a2enmod include. Now, tortoisesvn can't access the repo; it always returns a 301 permanent redirect. Some playing with it reveals I can access it in a browser if I'm sure to include the trailing / but it still doesn't work in TortoiseSVN. I've looked at all of the faq's for this problem with TortoiseSVN and apache, and none of them seem to apply to my problem. Anyone have any insight into this problem? I'm running Ubuntu 9.10 with Apache 2.2.12. The only change I've made to my configuration is to enable the includes mod. Here's my dav_svn conf: <Location /svn> DAV svn SVNParentPath /home/matthew/svn AuthType Basic AuthName "Subversion repository" AuthUserFile /etc/subversion/passwd Require valid-user </Location> and here's the relevant part of my virtual host conf: <Location /svn> SetHandler None Order allow,deny Allow from all </Location> Edit: OK, I've discovered that the real conflict is between the include module and basic authentication. That is, if I disable the include module, browse to the subversion repo, enter my user/pass for the basic authentication, I can browse it just fine. It even continues to work after I re-enable the include module. However, if I browse with another browser where I'm not already authenticated, then it no longer works.

  Read the article

• XDEBUG/PHP doesn't dump profile even when set up properly?

  - by John D.

  I installed xdebug from source, but also tried my package manager (separately) and they both are loaded correctly (verified by restarting Apache and seeing the xdebug copyright info in phpinfo()) but they do not dump profiling information. Out of the 40 different attempts of configuration it logged once or twice but I lost what I did, I tried with first only loading the module in php.ini with no settings, but it didn't log to /tmp/. I tried many different settings but my current is now: xdebug.profiler_enable = Off xdebug.profiler_enable_trigger = 1 xdebug.profiler_output_dir = "/tmp/" xdebug.profiler_output_name = "profiler.%t" Of course I call my script through 127.0.0.1/test.php?XDEBUG_PROFILE, which is for enable_trigger. Do you know why it would not dump profiler information? nobody (Arch Linux) can write to /tmp/ as it has before, so I'm sure it is not a permissions error. Apache's error_log does not tell me anything about xdebug either, as it has loaded correctly. It just does not "work"! EDIT: I made a subfolder "xdebug_profiles" in /tmp/ and chown'ed it to nobody, and now it works flawlessly. I'm not sure why it couldn't write before, I guess it's just a caveat with nobody on Arch. I answered my own question , not enough points to answer it or comment, so consider this answered.

  Read the article

• process and memory issue on linux server

  - by zapping

  Need some assistance in analyzing apache and php process running on linux server. Its a 8-core intel processor with 4GB ram. When the website on it runs the top displays like this. PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 23459 username1 16 0 151m 27m 8388 S 11.3 0.7 0:11.71 php5 23730 username1 16 0 151m 28m 8388 S 11.3 0.7 0:03.87 php5 23458 username1 16 0 151m 28m 8388 S 3.0 0.7 0:19.20 php5 16202 mysql 15 0 459m 38m 4624 S 0.7 1.0 62:33.81 mysqld 24141 nobody 15 0 311m 5832 2304 S 0.3 0.1 0:00.03 httpd Why does the command say php5 when the website is accessed. Both apache and php was preconfigured so not sure whats done there. Tried setting up the same site and db on a different server but on it the process shows httpd always and not php5. The site uses mysql db. The problem is server load seems to go till about 5.x when the website was access by about 16users. When the free -m command was given the output shows total used free shared buffers cached Mem: 3941 3727 213 0 236 2734 -/+ buffers/cache: 756 3184 Swap: 4095 0 4095 Lots of memory seems to be in cache and free memory is less. Even when the website is not accessed that is leaving it very much idle for about 2days the free memory showed just 190. When the site is accessed the free memory seems to be go till 90mb then it increases to about 150mb. It always seems to remain just about 200mb. Is it somehow related to the server load showing 5.x. Will adding some more RAM resolve the load issue?

  Read the article

• localhost won't load after adding config data to httpd

  - by OldWest

  I am not very experienced with configuring httpd, and I am following a tutorial to view my site w/ domain name under localhost. My localhost just blanks out and my apache services won't restart. I checked all of my paths and they are correct. I am editing the w*indows/system32/drivers/etc/host*s file and my apache httpd file. This is what I am putting in my hosts file: 127.0.0.1 www.cars_v1.0.com.localhost And in the footer of my httpd file I am putting this: <VirtualHost 127.0.0.1:80> ServerName www.cars_v1.0.com.localhost DocumentRoot "C:\wamp\www\symfony\cars_v1.0\web" DirectoryIndex index.php <Directory "C:\wamp\www\symfony\cars_v1.0\web"> AllowOverride All Allow from All </Directory> Alias /sf C:\wamp\www\symfony\cars_v1.0\lib\vendor\symfony-1.4.8\data\web\sf <Directory "C:\wamp\www\symfony\cars_v1.0\lib\vendor\symfony-1.4.8\data\web\sf"> AllowOverride All Allow from All </Directory> </VirtualHost>

  Read the article

• Browser sends http request with RANGE

  - by nute

  I have a local testing environment in a Fedora virtual machine. Strangely, resources (css and js files) don't seem to work. Looking at Firebug, I see that the browser sends the HTTP request with "Range bytes=0-". The server responds with either an empty 200OK or an empty 206 Partial Content. Here is an example: Response Headers Date Mon, 23 Nov 2009 23:33:26 GMT Server Apache/2.2.13 (Fedora) Last-Modified Thu, 19 Nov 2009 22:58:55 GMT Etag "18-3aec-478c14dbee138" Accept-Ranges bytes Content-Length 15084 Content-Range bytes 0-15083/15084 Connection close Content-Type text/css Request Headers Host fedora.test User-Agent Mozilla/5.0 (X11; U; Linux i686; en-US; rv:1.9.1.5) Gecko/20091105 Fedora/3.5.5-1.fc11 Firefox/3.5.5 Accept text/css,*/*;q=0.1 Accept-Language en-us,en;q=0.5 Accept-Encoding gzip,deflate Accept-Charset ISO-8859-1,utf-8;q=0.7,*;q=0.7 Keep-Alive 300 Connection keep-alive Referer http://fedora.test/pictures/ Cookie __utma=26341546.1613992749.1258504422.1258569125.1258752550.4; __utmz=26341546.1258504422.1.1.utmcsr=(direct)|utmccn=(direct)|utmcmd=(none); PHPSESSID=tqf8jfmc77qihe97rl4tmhq685 Range bytes=0- If-Range "18-3aec-478c14dbee138" I don't know if the browser is sending the wrong request, or if it's the server that is doing this. Request made to the outside (such as google analytics) are working fine. This is running in Fedora 11 in VirtualBox. Apache. PHP. The files are being served through the "shared folders" feature of VirtualBox (could it be related?). No error logs could help me.

  Read the article

• Trouble serving vhosts when trying to set up wildcard subdomains with dnsmasq in local development e

  - by Jeremy Kendall

  I'm trying to get wildcard DNS enabled on my laptop using dnsmasq. I realize that this has been asked and answered more than once on this forum, but I can't get the solution to work for me. Steps taken so far: Installed dnsmasq Set address=/example.dev/127.0.0.1 in dnsmasq.conf Set listen-address=127.0.0.1 in dnsmasq.conf Ensured nameserver 127.0.0.1 is in /etc/resolv.conf Set prepend domain-name-servers 127.0.0.1; in /etc/dhcp3/dhclient.conf Created a vhost for example.dev Restarted apache and dnsmasq Note: example.dev is not set in /etc/hosts My vhost for example.dev <VirtualHost *:80> ServerName example.dev DocumentRoot /home/jkendall/public_html/example/public ServerAlias *.example.dev # This should be omitted in the production environment SetEnv APPLICATION_ENV development <Directory /home/jkendall/public_html/example/public> DirectoryIndex index.php AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> The setup above will server example.dev locally without any problem. It will also serve test.example.dev, but test.example.dev returns the default apache "It works!" index.html from /var/www rather than my index.php in /home/jkendall/public_html/example/public. The solution in this Server Fault thread suggests that address=/.example.dev/127.0.0.1 would resolve my problem, but when I try to use that solution, restarting dnsmasq results in a failure with the error message dnsmasq: error at line 62 of /etc/dnsmasq.conf For grins, I moved my project over to /var/www/example and modified the vhost appropriately. I got the same result as described above. At this point I'm not sure what other steps I can take to resolve the issue. Thoughts?

  Read the article

• What is optimal hardware configuration for heavy load LAMP application

  - by Piotr K.

  I need to run Linux-Apache-PHP-MySQL application (Moodle e-learning platform) for a large number of concurrent users - I am aiming 5000 users. By concurrent I mean that 5000 people should be able to work with the application at the same time. "Work" means not only do database reads but writes as well. The application is not very typical, since it is doing a lot of inserts/updates on the database, so caching techniques are not helping to much. We are using InnoDB storage engine. In addition application is not written with performance in mind. For instance one Apache thread usually occupies about 30-50 MB of RAM. I would be greatful for information what hardware is needed to build scalable configuration that is able to handle this kind of load. We are using right now two HP DLG 380 with two 4 core processors which are able to handle much lower load (typically 300-500 concurrent users). Is it reasonable to invest in this kind of boxes and build cluster using them or is it better to go with some more high-end hardware? I am particularly curious how many and how powerful servers are needed (number of processors/cores, size of RAM) what network equipment should be used (what kind of switches, network cards) any other hardware, like particular disc storage solutions, etc, that are needed Another thing is how to put together everything, that is what is the most optimal architecture. Clustering with MySQL is rather hard (people are complaining about MySQL Cluster, even here on Stackoverflow).

  Read the article

• Intermittent PHP error: Undefined function <core function>

  - by Daniel

  In the last week I've been coming across an incredibly annoying error on one of Slicehost slices. It appears that every now and then PHP will fail with a fatal error, saying a certain function is undefined. The function changes, but is always a core PHP function e.g. defined(), version_compare(), etc. This problem has occurred while using several different PHP applications - PHPMyAdmin, my own custom built apps, etc, leading me to believe that the problem is not specific to the running code. Here are some details: - Debian Lenny - Apache 2.2.9 - PHP 5.2.6-1+lenny4 with Suhosin-Patch (running eAccelerator 0.9.6) Apache and PHP are installed from Debian packages. Error logs show nothing out of the ordinary. I thought memory might be an issue, but free -m reports upwards of 100MB free almost all the time. Another thing I'm trying to investigate is if the problem might be related to eAccelerator, but testing this theory out is incredibly hard because the issue doesn't appear very often and I've been using eAccelerator for months on this install without any problems up until now. Has anyone ever come across anything like this? Why would PHP report undefined core functions?

  Read the article

• Problem configuring virtual host.

  - by Zeeshan Rang

  I am tring to configure apache virtual host for my computer. But i am facing problem in doing so. i have made required changes in my C:\WINDOWS\system32\drivers\etc\hosts then C:\xampp\apache\conf\extra\httpd-vhosts.conf I added the following lines in httpd-vhosts.conf ########################Virtual Hosts Config below################## NameVirtualHost 127.0.0.1 <VirtualHost localhost> ServerName localhost DocumentRoot "C:\xampp\htdocs" DirectoryIndex index.php index.html <Directory "C:\xampp\htdocs"> AllowOverride All </Directory> </VirtualHost> <VirtualHost virtual.cloudse7en.com> ServerName virtual.cloudse7en.com DocumentRoot "C:\development\virtual.cloudse7en.com\httpdocs" DirectoryIndex index.php index.html <Directory "C:\development\virtual.cloudse7en.com\httpdocs"> Options Indexes FollowSymLinks Includes ExecCGI AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> <VirtualHost virtual.app.cloudse7en.com> ServerName virtual.app.cloudse7en.com DocumentRoot "C:\development\virtual.app.cloudse7en.com\httpdocs" DirectoryIndex index.php index.html <Directory "C:\development\virtual.app.cloudse7en.com\httpdocs"> Options Indexes FollowSymLinks Includes ExecCGI AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> ######################################################################## I started my xampp and tried http://localhost in a browser. This works and open up http://localhost/xampp/ but when i try http:http://virtual.app.cloudse7en.com it again opens up http://virtual.app.cloudse7en.com/xampp/ I do not understand the reason. Also i have a windows vista 64 bit, operating system. Do i need to make some other changes too? Regards Zee

  Read the article

• Centos: installing SVN tells I don't have perl 1.17. I have installed 5.8

  - by Emerson

  I'm trying to install SVN on a CentOS virtual machine. I used the command that the CentOS wiki tells: http://wiki.centos.org/HowTos/Subversion yum install mod_dav_svn subversion It gives me a few errors: --> Finished Dependency Resolution mod_dav_svn-1.4.2-4.el5_3.1.i386 from base has depsolving problems --> Missing Dependency: httpd-mmn = 20051115 is needed by package mod_dav_svn-1.4.2-4.el5_3.1.i386 (base) subversion-1.4.2-4.el5_3.1.i386 from base has depsolving problems --> Missing Dependency: perl(URI) >= 1.17 is needed by package subversion-1.4.2-4.el5_3.1.i386 (base) Error: Missing Dependency: perl(URI) >= 1.17 is needed by package subversion-1.4.2-4.el5_3.1.i386 (base) Error: Missing Dependency: httpd-mmn = 20051115 is needed by package mod_dav_svn-1.4.2-4.el5_3.1.i386 (base) The thing is that I have Perl 5.8 installed: root@server [~]# rpm -q perl perl-5.8.8-32.el5_5.2 I also don't know why it tells httpd-mmn isn't installed. I have apache installed for sure. From what I read here, it seems I would need to recompile apache. www.sitepoint.com /forums/showthread.php?t=485683 Any ideas? Update: I also tried to install subversion via WHM (11.28.35) and it gives me the same error. By the way, WHM it says: CENTOS 5.5 i686 virtuozzo on server

  Read the article

• Nginx proxy with Redmine SVN authentication.

  - by Omegaice

  I am attempting to setup a system where I have an nginx server running as a reverse proxy for multiple websites that I want to run. To separate the websites I have created a Linux container which contains each site to allow me to reduce conflicts in database usage etc. I am currently trying to get my main site working and have nginx with passenger setup and connecting to redmine and I have an Apache install specifically setup for serving the SVN over HTTP and am attempting to use the redmine authentication with that. I have set everything up as described in the redmine howtos, but when I check a project out from the SVN it always works even if the project is private and whenever I try and commit to the repositories it fails saying "Could not open the requested SVN filesystem", the Apache error log related to that event is "(20014)Internal error: Can't open file '/srv/rcs/svn/error/format': No such file or directory". If I take out the redmine authentication I can checkout and check-in repositories fine but there is no authentication. Does anyone have any ideas? Edit I tried to solve this problem another way by attempting to have the authentication work by LDAP, I managed to get it so that my user could log into the redmine website but as soon as I tried to check anything out it said that access was forbidden to the repository.

  Read the article

• How can I enable PHP5 for a site? Having problems with every single method.

  - by John Stephens

  I'm working on a client site that is hosted on someone's DIY Debian Linux server [Apache/1.3.33 (Debian GNU/Linux)], and I'm trying to install a script that requires PHP5. By default, the server parses .php files with PHP 4.3.10-22, which is configured at /etc/php4/apache/php.ini, according to phpinfo(). On the server I can see a config directory for PHP5 adjacent to the PHP4 directory: /etc/php5.0/apache2/php.ini. I have tried multiple methods to enable PHP5 for the document root where the site's files are hosted, including all available methods mentioned here. By far, the most common suggestion I've found is to add one or both of the following lines to the site's .htaccess file: AddHandler application/x-httpd-php5 .php AddType application/x-httpd-php5 .php Trouble is, when either or both of those lines are present, the site forces my browser to download any .php files requested, without parsing the PHP at all. All of the other methods mentioned in the above article cause a 500 Internal Server Error. There is no hosting control panel I can access in a browser to enable PHP5 for the site, but I do have shell access. When I asked the server administrator about this issue, he encouraged me to search for the answer on Google. Where could I begin to troubleshoot this issue? Are there ways to test or verify the server's specific PHP5 installation and configuration, using the command line or some other method? Do you have other suggestions to enable PHP5?

  Read the article

• Apahe configuration with virtual hosts and SSL on a local network

  - by Petah

  I'm trying to setup my local Apache configuration like so: http://localhost/ should serve ~/ http://development.somedomain.co.nz/ should serve ~/sites/development.somedomain.co.nz/ https://development.assldomain.co.nz/ should serve ~/sites/development.assldomain.co.nz/ I only want to allow connections from our local network (192.168.1.* range) and myself (127.0.0.1). I have setup my hosts file with: 127.0.0.1 localhost 255.255.255.255 broadcasthost ::1 localhost fe80::1%lo0 localhost 127.0.0.1 development.somedomain.co.nz 127.0.0.1 development.assldomain.co.nz 127.0.0.1 development.anunuseddomain.co.nz My Apache configuration looks like: Listen 80 NameVirtualHost *:80 <VirtualHost development.somedomain.co.nz:80> ServerName development.somedomain.co.nz DocumentRoot "~/sites/development.somedomain.co.nz" DirectoryIndex index.php <Directory ~/sites/development.somedomain.co.nz> Options Indexes FollowSymLinks ExecCGI Includes AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> <VirtualHost localhost:80> DocumentRoot "~/" ServerName localhost <Directory "~/"> Options Indexes FollowSymLinks ExecCGI Includes AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> <IfModule mod_ssl.c> Listen *:443 NameVirtualHost *:443 AcceptMutex flock <VirtualHost development.assldomain.co.nz:443> ServerName development.assldomain.co.nz DocumentRoot "~/sites/development.assldomain.co.nz" DirectoryIndex index.php SSLEngine on SSLCipherSuite ALL:!ADH:!EXPORT56:RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP:+eNULL SSLCertificateFile /Applications/XAMPP/etc/ssl.crt/server.crt SSLCertificateKeyFile /Applications/XAMPP/etc/ssl.key/server.key BrowserMatch ".*MSIE.*" \ nokeepalive ssl-unclean-shutdown \ downgrade-1.0 force-response-1.0 <Directory ~/sites/development.assldomain.co.nz> SSLRequireSSL Options Indexes FollowSymLinks ExecCGI Includes AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> </IfModule> http://development.somedomain.co.nz/ http://localhost/ and https://development.assldomain.co.nz/ work fine. The problem is when I request http://development.anunuseddomain.co.nz/ or http://development.assldomain.co.nz/ it responds with the same as http://development.somedomain.co.nz/ I want it to deny all requests that do not match a virtual host server name and all requests to a https host that are requested with http PS I'm running XAMPP on Mac OS X 10.5.8

  Read the article

• Securely executing system commands as sudo from PHP

  - by Aydin Hassan

  Is it possible? I have written a command line tool in PHP for creating new environments for our company. It creates system users, directories, databases, VHosts and restarts apache, amongst other things. These commands require sudo privileges. I thought it might be a nice idea to have a web-interface for it, to make it easier for other non-developers to use. The web app would be behind authentication. When running from the command line I just run sudo tool.php, obviously I can't do this from a web app. How could I do this securely? Giving the apache user sudo access seems silly, as this would means all sites hosted on the box (eg all our environments) would have sudo access. Is it possible to make this tool run under a different user? this user could have sudo privileges for only the commands I need? How do things like plesk and cPanel do this? Any thoughts?

  Read the article

• httpd 2.2.15 + suPHP + suExec + php5 = permission and information ?

  - by Prix

  Hi, i am currently playing around with suexec, suphp, php5 on my apache on slackware 13.1. Everything is installed and working properly but now i did like to got further into the directory permissions and at suphp settings and options available. initially i was planning to leave suphp disabled unless a virtualhost has it specified to be enabled but it does not seem to work, see sample: mod_php.conf which is included in my httpd.conf # # mod_php & mod_suPHP - PHP Hypertext Preprocessor module # # Load the PHP module: LoadModule php5_module lib/httpd/modules/libphp5.so # Load the suPHP module: LoadModule suphp_module lib/httpd/modules/mod_suphp.so <IfModule mod_php5.c> # Tell Apache to feed all *.php files through PHP. If you'd like to # parse PHP embedded in files with different extensions, comment out # these lines and see the example below. <FilesMatch \.php$> SetHandler application/x-httpd-php </FilesMatch> </IfModule> <IfModule mod_suphp.c> # This option tells mod_suphp if a PHP-script requested on this server (or # VirtualHost) should be run with the PHP-interpreter or returned to the # browser "as it is". suPHP_Engine off </IfModule> With the above first sample it makes suPHP and PHP not work if i comment out the php5 stuff but the module it will run just fine ... So my first question is, how could i possible make this setup work ? Leave suPHP disabled using php5 by default and if a virtualhost has suPHP enabled it will disable php5 and use suPHP. if any information is lacked here please let me know and i will update with any additional information you may need. Thanks in advance.

  Read the article

• How to debug slow queries in Django+Postgres

  - by lacker

  My database queries from Django are starting to take 1-2 seconds and I'm having trouble figuring out why. Not too big a site, about 1-2 requests per second (that hit Django; static files are just served from nginx.) The thing that confuses me is, I can replicate the slowness in the Django shell using debug mode. But when I issue the exact same queries at an sql prompt they are fast. It takes about a second for a query to return, but when I check connection.queries it reports the time as under 10 ms. Here's an example (from the Django shell): >>> p = PlayerData.objects.get(uid="100000521952372") >>> a = time.time(); p.save(); print time.time() - a 1.96812295914 >>> for d in connection.queries: print d["time"] ... 0.002 0.000 0.000 How can I figure out where this extra time is being spent? I'm using Apache+mod_wsgi in daemon mode, but this happens with just the django shell as well, so I figure it is not apache-related.

  Read the article

• how to edit source files and commit the changes to the new website?

  - by ajsie

  i've got ubuntu installed with lamp. im using webdav to upload/download files to/from the ubuntu web server, after i have edited the php source files in netbeans. however, i wonder what is best practice for editing source files and committing these changes to the new website. cause if we are 2-3 developers, i guess we have to use svn. but i have never used it before so i wonder how it works. should i install it and then select the /var/www (apaches webroot) as the repository folder? then when i check in, all the changes will apply immediately? could someone please explain following steps: how to download, edit the source files, upload the files and see the new changes in the website. cause i have only worked with a local apache before, and it was only me. now there will be some more programmers so i have to set up a decent, central environment for this, and have to know how netbeans, svn, webdav and apache works all together. thanks!

  Read the article

< Previous Page | 117 118 119 120 121 122 123 124 125 126 127 128  | Next Page >