Search Results

Search found 4893 results on 196 pages for 'expect'.

Page 121/196 | < Previous Page | 117 118 119 120 121 122 123 124 125 126 127 128  | Next Page >

• Disk IO slow on ESXi, even slower on a VM (freeNAS + iSCSI)

  - by varesa

  I have a server with ESXi 5 and iSCSI attached network storage(4x1Tb Raid-Z on freenas 8.0.4). Those two machines are connected to each other with Gigabit ethernet. The raid-z volume is divided into three parts: two zvols, shared with iscsi, and one directly on top of zfs, shared with nfs and similar. I ssh'd into the freeNAS box, and did some testing on the disks. I used ddto test the third part of the disks (straight on top of ZFS). I copied a 4GB (2x the amount of RAM) block from /dev/zero to the disk, and the speed was 80MB/s. Other of the iSCSI shared zvols is a datastore for the ESXi. I did similar test with time dd .. there. Since the dd there did not give the speed, I divided the amount of data transfered by the time show by time. The result was around 30-40 MB/s. Thats about half of the speed from the freeNAS host! Then I tested the IO on a VM running on the same ESXi host. The VM was a light CentOS 6.0 machine, which was not really doing anything else at that time. There were no other VMs running on the server at the time, and the other two "parts" of the disk array were not used. A similar dd test gave me result of about 15-20 MB/s. That is again about half of the result on a lower level! Of course the is some overhead in raid-z - zfs - zvolume - iSCSI - VMFS - VM, but I don't expect it to be that big. I belive there must be something wrong in my system. I have heard about bad performance of freeNAS's iSCSI, is that it? I have not managed to get any other "big" SAN OS to run on the box (NexentaSTOR, openfiler). Can you see any obvious problems with my setup?

  Read the article

• cURL hangs trying to upload file from stdin

  - by SidneySM

  I'm trying to PUT a file with cURL. This hangs: curl -vvv --digest -u user -T - https://example.com/file.txt < file This does not: curl -vvv --digest -u user -T file https://example.com/file.txt What's going on? * About to connect() to example.com port 443 (#0) * Trying 0.0.0.0... connected * Connected to example.com (0.0.0.0) port 443 (#0) * SSLv3, TLS handshake, Client hello (1): * SSLv3, TLS handshake, Server hello (2): * SSLv3, TLS handshake, CERT (11): * SSLv3, TLS handshake, Server key exchange (12): * SSLv3, TLS handshake, Server finished (14): * SSLv3, TLS handshake, Client key exchange (16): * SSLv3, TLS change cipher, Client hello (1): * SSLv3, TLS handshake, Finished (20): * SSLv3, TLS change cipher, Client hello (1): * SSLv3, TLS handshake, Finished (20): * SSL connection using DHE-RSA-AES256-SHA * Server certificate: * subject: serialNumber=jJakwdOewDicmqzIorLkKSiwuqfnzxF/, C=US, O=*.example.com, OU=GT01234567, OU=See www.example.com/resources/cps (c)10, OU=Domain Control Validated - ExampleSSL(R), CN=*.example.com * start date: 2010-01-26 07:06:33 GMT * expire date: 2011-01-28 11:22:07 GMT * common name: *.example.com (matched) * issuer: C=US, O=Equifax, OU=Equifax Secure Certificate Authority * SSL certificate verify ok. * Server auth using Digest with user 'user' > PUT /file.txt HTTP/1.1 > User-Agent: curl/7.19.4 (universal-apple-darwin10.0) libcurl/7.19.4 OpenSSL/0.9.8l zlib/1.2.3 > Host: example.com > Accept: */* > Transfer-Encoding: chunked > Expect: 100-continue > < HTTP/1.1 100 Continue

  Read the article

• DNS something is wrong?

  - by Nickolas R.

  Hello I am configuring bind9 on a server with two network interfaces, one is connected to the LAN and the other is connected to the Internet through NAT so bind is not faced directly to the Internet. Everything seems to work fine, clients can do both forward and reverse lookups but somethings seems strange. On the server if i try to ping www.google.com one time, a great amount of network activity is genereated, alot more that one would expect so i decided to sniff the traffic with tcpdump. When loading the dump into Wireshark i can see about 250 entries with "Standard query A" and "Standard query response" Here a some of the entries from the dump DNS Standard query A www.google.com DNS Standard query A blackhole-1.iana.org DNS Standard query A blackhole-2.iana.org DNS Standard query response DNS Standard query A ns2.isc-sns.com DNS Standard query A ns1.isc-sns.net DNS Standard query A ns3.isc-sns.info DNS Standard query response PTR b.iana-servers.net RRSIG DNS Standard query A auth2.dns.cogentco.com DNS Standard query A ns1.crsnic.net DNS Standard query A ns2.nsiregistry.net DNS Standard query A ns3.verisign-grs.net DNS Standard query A ns4.verisign-grs.net DNS Standard query PTR 79.52.19.199.in-addr.arpa I do not have too much experince with DNS yet, but i am pretty sure that something is wrong. Anybody that have an idea of whats is going on?

  Read the article

• Password Manager that allows syncing accross platforms

  - by lexu

  I use OS X, Linux, Solaris and windows for work and from home. There are good tools that allow me to manage the many logins/passwords required platform independently. But mostly they expect me to carry a thumb-drive around or require direct access to a central location (a sky drive in the cloud). The thumb-drive is too easily lost (= synchronized backup needed), the central location not always reachable/ mountable. Besides company policy rightly prevents this often. Is there a tool that allows me to add passwords locally and then syncs it's DB with the "mother-ship" later. Or is there another approach that you use, that solves my problem? EDIT My question is more about "synchronize" than cross platform. I've evaluated (=read feature list) some good cross platform tools, but need one that does the synchronizing for me. By synchronize I mean "merge two versions" not "replace (hopefully) old file with new." I'm not sure I'm always disciplined/awake enough to prevent data loss. UPDATE Lifehacker just posted that AgileSolutions now have a beta version of 1Password for Windows.

  Read the article

• Improving IO with FlashCache

  - by Devator

  I have a server with 2 HDD's (2x 1 TB), running in RAID 1 (SW-RAID). I want to improve IO performance by using flashcache. There are running KVM virtual machines on it, using LVM. Regarding this, I have the following questions: Will this even work? flashcache works for block devices, however these are all virtual machines with their own setup. How much would I expect to increase performance? Most virtual machines run websites and some host games. How big does the SSD needs to be? Would having a bigger SSD increase performance since it's able to cache more files? What happens if the SSD dies? Would flashcache retrieve files from the traditional HDD and I could simply replace the SSD? How much faster would writeback be in comparison with writethrough and writearound? I have no access to a test system unfortunately, so could I install flashcache on a live server without unmounting the the disks? I found a great tutorial here which I would be using.

  Read the article

• No digital audio output with Asus Xonar DG

  - by Lunatik

  I've purchased an Asus Xonar DG as replacement for faulty onboard audio in a Medion 8822 as it has an optical output which is all I really need to feed my HTPC. I uninstalled the previous drivers/devices, switched the PC off, inserted the Asus card, powered up, disabled the onboard audio in the BIOS, then installed the driver that came on the CD (same version as on Asus' website as of today) and everything went perfectly - no errors. I set the audio devices up in Windows and in the Asus utility (SPDIF enabled, 6-ch audio) as I would expect to see them work, but the only thing is I have no digital audio from test tones within Windows/the Asus utility, PCM audio or Dolby Digital from DVD. Analogue audio is fine. I've uninstalled things and reinstalled a couple of times now, as well as trying almost all combinations of analogue/digital outputs but can't get it sorted. Does anyone have any tips on how to get this working? This card has just been released so there isn't much out there to go on. Notes: The light on the toslink port is lit. OS is Vista 32-bit SP2 and all up to date, pretty much a fresh install with almost no 3rd party applications installed This page seems to suggest that a digital output device in Windows is not needed with Xonar cards as it was with the previous Realtek so I have it set to Analog. The only other output device is S/PDIF pass-thru

  Read the article

• Struggling to set-up NLB cluster

  - by Chris W

  I'm trying to set up NLB on a couple of Windows 2008 R2 virtual servers running on top of Hyper V R2. The servers each have a single vNIC for LAN access (and a second vNIC for SAN access). I'm setting up the cluster to use Multicast mode. The vNICs are each set to allow MAC spoofing. Essentially I'm finding that i can add SERVER1 as a host and it will pick up and respond to the cluster IP from a remote subnet. If I then 'stop' the node in NLB manager it still responds when I would expect it to stop answering on that IP. If I recreate the cluster and add SERVER2 as the first host, the wizard completes correctly and an IPCONFIG on the server shows that it now has the cluster IP but I can't ping the cluster IP from a remote subnet but I can from another machine on the same subnet. As a final test - with both servers in the cluster, pinging from another machine on the same subnet I still get a response from the cluster IP when both nodes are stopped according to the NLB manager. The two VMs are sat on the same physical blade and are built up exactly the same as they'll be used as SharePoint web front end servers. I'm at a loss as to what could be wrong with the second VM that prevents it taking on the address just as the sole node in the cluster, never mind the strange behaviour of the cluster when I stop/start nodes.

  Read the article

• location of index.html CentOS 6

  - by user2118559

  Based on this http://www.servermom.com/how-to-add-new-site-into-your-apache-based-centos-server/454/ tutorial installed Apache-based CentOS Server I use putty.exe as editor vi /etc/httpd/conf/httpd.conf at very bottom modified to <VirtualHost *:80> ServerAdmin [email protected] DocumentRoot /var/www/fikitipis.com/public_html ServerName www.fikitipis.com ServerAlias fikitipis.com ErrorLog /var/www/fikitipis.com/error.log CustomLog /var/www/fikitipis.com/requests.log common </VirtualHost> So expect that index is at /var/www/fikitipis.com/public_html When in browser type ip address of server, see Apache 2 Test Page powered by CentOS and so on You may now add content to the directory /var/www/html/ Then [root@vps ~]# ls /var/www/ see cgi-bin domain.com error fikitipis.com html icons Checking content of directories ls /var/www/domain.com/public_html, ls /var/www/fikitipis.com/public_html, /var/www/html/ are empty Where is index.html? Did touch /var/www/fikitipis.com/public_html/index1.html then vi /var/www/fikitipis.com/public_html/index1.html, typed a, then wrote some text in file, then Escape and shift+zz. And in browser http://111.111.11.111/index1.html and see what I had wrote. So until now seems that all works

  Read the article

• Postfix relay gives error 450 while it should be 550

  - by dieter-be

  Hi, we use postfix to do relaying. We get several messages like the following in /var/log/mail (slightly edited) Apr 13 13:30:29 linserver postfix/smtpd[1064]: NOQUEUE: reject: RCPT from unknown[$ip]: 450 4.1.1 <[email protected]>: Recipient address rejected: undeliverable address: host domain.be [$ip] said: 550 <[email protected]>: Recipient address rejected: User unknown in virtual mailbox table (in reply to RCPT TO command); from=<[email protected]> to=<[email protected]> proto=ESMTP helo=<BLUESTREAK.domain.local> Now, when the master mail servers gives a 550, claiming that the user does not exist, I want the relay to also give a 550 back. What happens now is that it seems to return a 450, causing clients to keep messages queued, keep trying and only notify users after a certain period has passed. According to what I could find, the soft_bounce could cause this. But we have not enabled this option (and by default it's off according to postfix docs) It might also have something to do with the *_reject_code postconf values. Especially since the log message complains the unknown ip. But as you can see in the postconf output below, smtpd_sender_restrictions and smtpd_client_restrictions are empty. So even if it would try to do any restrictions there, 550 is the "worst" error going on, so that's what I expect to be returned to the client. postconf: http://sprunge.us/JYgB Thanks, Dieter

  Read the article

• Linux Scheduler (not using all cores on multi-core machine) RHEL6

  - by User512

  I'm seeing strange behavior on one of my servers (running RHEL 6). There seems to be something wrong with the scheduler. Here's the test program I'm using: #include <stdio.h> #include <unistd.h> #include <stdlib.h> void RunClient(int i) { printf("Starting client %d\n", i); while (true) { } } int main(int argc, char** argv) { for (int i = 0; i < 4; ++i) { pid_t p_id = fork(); if (p_id == -1) { perror("fork"); } else if (p_id == 0) { RunClient(i); exit(0); } } return 0; } This machine has a lot more than 4 cores so we'd expect all processes to be running at 100%. When I check on top, the cpu usage varies. Sometimes it's split (100%, 33%, 33%, 33%), other times it's split (100%, 100%, 50%, 50%). When I try this test on another server of ours (running RHEL 5), there are no issues (it's 100%, 100%, 100%, 100%) as expected. What's causing this and how can I fix it? Thanks

  Read the article

• Mac "Steam needs to be online to update" - 404 fetching *_osx.zip.*

  - by Chris Boyle

  Since yesterday evening, when I launch Steam on OSX, a self-update progress bar appears instead (at 0 of 30MB or so). This bar does not advance, an error dialog appears: Steam needs to be online to update Please confirm your network connection and try again. The app then exits. This happens whether wifi or ethernet or both are connected, and pings to the outside world succeed throughout. If I look at the logs in Console, they are very similar to this example (though that's not mine). Specifically: Success! http://store.steampowered.com/public/client/steam_client_osx?date=718277 [...] Failed! http://cdn.store.steampowered.com/public/client/breakpad_osx.zip.27f59114a86fcd50533e1d7b128f9300947f9969 Failed! http://cdn.store.steampowered.com/public/client/steam_osx.zip.11a99384214805f2dd3be5084ba6be61d662f8ac Failed! http://cdn.store.steampowered.com/public/client/miles_osx.zip.d9fb546541f59c1fdd03962a605236b1021abab8 Requesting the first URL successfully returns some data including the filenames of the latter three, and requesting any of those gives me a 404 (I've tried multiple clients on multiple continents). Searches on Google and Twitter show about 10-20 others having this problem in the past 24 hours, but hardly the angry mob I'd expect if the problem affected all Steam OSX users. Things that have already been tried with no effect: Switching between wifi and ethernet. Killing all Steam processes including ipcserver. Moving the ~/Library/Application Support/Steam/registry.vdf file away. Requesting those URLs with other clients and from other locations. Interesting: that first URL with the date parameter returns the same content even without that parameter (thus would lead to the same 404s) suggesting that the problem is not necessarily specific to coming from a particular currently-installed version of Steam.

  Read the article

• Best way to 'harden' embedded ext4 file server against unexpected loss of power?

  - by Jeremy Friesner

  Hi all, First, a little background: my company makes an audio streaming device that is a headless, rack-mounted Linux box with a couple of SSDs attached. Each SSD is formatted with ext4. The users can connect to the system using Samba/CIFS to upload new audio files or access existing ones. There is also custom software for streaming out audio over the network. This is all fine. The only problem is that the users are audio people, not computer people, and see the system as a 'black box', not as a computer. Which means that at the end of the day, they aren't going to ssh in to the box and enter "/sbin/shutdown -h"; they are just going to cut power to the rack and leave, and expect things to still work properly the next day. Since ext4 has journalling, journal checksumming, etc, this mostly works. The only time it doesn't work is when someone uploads a new file via Samba and then cuts power to the system before the uploaded data has been fully flushed to the disk. In that case, they come in the next day and find that their new file has been truncated or is missing entirely, and are unhappy. My question is, what is the best way to avoid this problem? Is there a way to get smbd to call "sync" at the end of every upload? (Performance on uploads isn't so important, since they only happen occasionally). Or is there a way to tell ext4 to automatically flush within a few seconds of any change to a file? (Again, performance can be sacrificed for safety here) Should I set a particular write-ordering mode, activate barriers, etc?

  Read the article

• The RTL8111/8168B NIC under Linux and the r8168 driver

  - by nik

  So I've got one of the infamous R8168 Realtek ethernet NIC, which have some problems under Linux. After some research, I found out I had to use the r8168 driver for this card (and not the r8169 which still loads when nothing else is available), which I did. So now everything works fine... Sort of. My download and upload rates are more than halved compared to what I should get. When I test (with eg. speedtest) I get something like 20M (often 15M) in download and 30M in upload, but if I test under Windows (everything is otherwise identical: same ethernet cable, same connection, at the same time of the day (well 5 min apart)...), I get 50M upload/download (which is what I expect). Where can it come from? Here's some info: ~ # lspci [...] 06:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) ~ # modinfo r8168 filename: /lib/modules/3.2.1-gentoo-r2/net/r8168.ko version: 8.027.00-NAPI license: GPL description: RealTek RTL-8168 Gigabit Ethernet driver author: Realtek and the Linux r8168 crew <[email protected]> srcversion: 0A6E9F1D4E8E51DE4B6BEE3 alias: pci:v00001186d00004300sv00001186sd00004B10bc*sc*i* alias: pci:v000010ECd00008168sv*sd*bc*sc*i* depends: vermagic: 3.2.1-gentoo-r2 SMP mod_unload [...] ~ # mii-tool -v eth0: negotiated 100baseTx-HD, link ok product info: vendor 00:07:32, model 17 rev 4 basic mode: autonegotiation enabled basic status: autonegotiation complete, link ok capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD advertising: 100baseTx-HD 10baseT-FD 10baseT-HD flow-control link partner: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD

  Read the article

• Cisco Pix 515 ip addressing

  - by Rickard

  I have just gotten my hands on a Cisco Pix 515 (not 515E) with 3 interfaces, and are just about to start some labs. In my lab, I am using a real life scenario from an actual setup at work. As I have no access to the device at work, I am simply trying to replicate the scenario by trial and error. At work, we are given two IP addresses from the provider, which is 1-to-1 nated addresses. The addresses we are allowed to use are: 10.131.35.4-5/29 Now, we have 3 servers on a DMZ, 192.168.2.2-4/24 and 17 client computers on 192.168.1.100-117/24 aswell as some static addressed devices on 192.168.1.8-18/27 My question is, how would I best set up so that the machines on the DMZ get's translated to 10.131.35.4 and the machines on 192.168.1.* will be translated to 10.131.35.5 I don't expect or want anyone to give me a fully functional config, I may learn from it, but I'd prefer to just have some advices or maybe a guide on how to set it up. I hope someone can shed some light over my situation, have been looking through google but I guess I don't the searchwords I'm using isn't too good as I can't find any good clues. THank you very much! PS. Maybe I should add, I am not unfamiliar with the Cisco CLI, as I prefer using that before any gui's. So not really looking for any solutions for the ASDM. DS.

  Read the article

• Why can't I specify the executable that opens file with extension on windows?

  - by Glen S. Dalton

  I am on windows server 2003, but I guess it is the same on windows xp. This is a superuser question, because it is definitly desktop, so do not move or close it. Question: I copied some movable applications (usually people create them for usb sticks) to locations like c:\bin\app1\app1.exe app1.exe can open files of type *.ap1 When I rightclick file.ap1 and choose "open with ..." the "Open with" dialog appears. But it is not working how I expect in this situation. I can choose c:\bin\app1\app1.exe with the "Browse" button, but: app1.exe will not appear in the dialog where I just choosed it in the programs list, like I am used to it after clicking OK on it in the browse dialog. app1.exe will not open it when I click ok in the "Open with" dialog, the application that was assigned until then will still open it What could be the reason? Edit: Additional Information: my account is member of the administrators group I just changed the permissions of the folder c:\bin\app1\ and made sure that the group "Administrators" has all rights. I also inherited this manually to all subfodlers and subfiles.

  Read the article

• How to manually start and re-start Apache with mod_wsgi powering a password protected Python WSGI app?

  - by Mahmoud Abdelkader

  I'm working on a project where I have to meet some regulatory requirements that require at least 3 out of 5 authorized users to start a backend web service that handles very sensitive information using pre-assigned passwords. Right now, the prototype has been approved and is running using Python's wsgiref.simple_server(), which I have programmed to manually prompt for the passwords. Now that the prototype has been approved, I have to migrate the web application to a production environment where I will need to run it behind Apache and mod_wsgi. I have two questions: Right now, I use a thin Python wrapper around expect to programmatically allow for remote password entry. How do I get Apache to prompt me for a password before starting? Will this have to be in the app.wsgi script that's executed by mod_wsgi? How would that work since Apache daemonizes, and thus, has no stdin! Will I have to worry about some type of code reload? Apache probably has some maximum number of requests before it kills and restarts another worker process, but, would this require a password prompt as well?

  Read the article

• Failed to su after making a chroot jail

  - by arepo21

  On a 64 bit CentOS host I am using script make_chroot_jail.sh to put a user in a jail, not permitting it to see anything expect it's home at /home/jail/home/user1. I did it typing this: sudo ./make_chroot_jail.sh user1 after, when trying to connect to user1 first i was getting an error like: /bin/su: user guest does not exist i have fixed this by copying some missed libraries: sudo cp /lib64/libnss_compat.so.2 /lib64/libnss_files.so.2 /lib64/libnss_dns.so.2 /lib64/libxcrypt.so.2 /home/jail/lib64/ sudo cp -r /lib64/security/ /home/jail/lib64/ But now, when trying to connect to user1 typing su user1 and then typing it's password, i am getting this error: could not open session So the question is how to connect to user1 in this situation? P.S. Here are the permissions of some files, this might be helpful in order to provide a solution: -rwsr-xr-x 1 root root /home/jail/bin/su drwxr-xr-x 4 root root /home/jail/etc -rw-r--r-- 1 root root /home/jail/etc/pam.d/su -rw-r--r-- 1 root root /home/jail/etc/passwd -rw------- 1 root root /home/jail/etc/shadow UPDATE1 After some modifications i managed to connect to user1, but the session closes immediately! I guess this a PAM issue, however cant find a way to fix it. Here the log entry for close action from /val/log/secure: Oct 6 15:19:42 localhost su: pam_unix(su:session): session closed for user user1 What makes the session to exit immediately after launching?

  Read the article

• Strange difference in bash behavior across systems

  - by pinkie_d_pie_0228

  I have two systems, an Ubuntu computer and an Android tablet. I have built and configured bash for Android to be used in adb, so it's the same version as my Ubuntu bash, and they use mostly the same bashrc and configuration, and the same exact options set by shopt. However, there is a slight difference in that the Android bash behaves as I expect when I I try to tab-complete something using a variable in it, but the Ubuntu bash doesn't. #Android ls $HOME/loc<tab> => ls $HOME/local #As expected Basically, the variable is taken into account when completing. But then #Ubuntu ls $HOME/loc<tab> => ls \$HOME/loc #Undesired behavior. The list of options is as follows, and is the same in both builds of bash. autocd:checkwinsize:cmdhist:expand_aliases:extglob:extquote:force_fignore:histappend:interactive_comments:progcomp:promptvars:sourcepath What can be making the Ubuntu version escape the $ instead of using it for completion as in the Android build? What can I do to make both work the same way? Any help will be greatly appreciated.

  Read the article

• Trying to understand Wireless N vs Wireless AC

  - by EGHDK

  Whenever a new wireless standard gets approved you expect faster speeds and longer range. From everything that I've read about it, it seems that AC will only transfer over the 5GHz band and up to 3Gbps. Studying the new AC routers on the market, it seems that they will transfer over 5GHz and 2.4GHz. And 5GHz will only transfer at 1.3Gbps. Which isn't what AC is supposed to be. I know there is a difference between what the standard actually says, and what products will actually do, but is there any reason for this? Is there any other main differences between AC and N? I've heard people discussing AC and saying that it's finally "fixing" what N was supposed to fix... what do they mean by that? Any security benefits? I have seen this image online: Will AC really do that? Will that require an AC network card in my laptop for that to actually happen? Lastly, will the router only be able to communicate with AC devices if I have beamforming technology on? I know it's a ton of questions, but most articles online seem to be outdated, and don't provide too much reliability.

  Read the article

• Apache Process question about RAM usage

  - by Andrew Fashion

  So everytime I load a new page, I notice a new HTTPD process opens, every time I click a page, and each process says it's using anywhere from 2-4.5% of memory. Does that mean every single process is running at that time using 2-4% of RAM? It's a brand new server and I'm the only one on the server at the moment. Or does it mean all the other processes are dying, and only the new one is active. Because 4% of my 2048MB of RAM is already 82MB for just one process!?!? Let me know, because I am trying to determine what I need to beef my server up in order to handle high loads of traffic. I'm expect to get 20,000 uniques per day on launch. I am currently running a Dual Quad Xeon server, with only 2GB of ram, I will upgrade to 8GB or more shortly. Let me know what you suggest! thank you [root@D18634 log]# top | grep 'httpd' 11315 apache 15 0 362m 82m 24m R 12.3 4.1 0:03.00 httpd 11310 apache 16 0 322m 41m 21m S 5.7 2.1 0:02.98 httpd 11315 apache 15 0 362m 83m 25m S 24.3 4.1 0:03.73 httpd 11319 apache 16 0 324m 42m 20m R 1.0 2.1 0:01.85 httpd 11319 apache 16 0 362m 82m 23m R 78.5 4.1 0:04.21 httpd 11321 apache 16 0 323m 44m 23m S 35.3 2.2 0:04.13 httpd 11319 apache 15 0 361m 82m 23m S 8.3 4.1 0:04.46 httpd 11321 apache 15 0 323m 44m 23m S 35.9 2.2 0:05.21 httpd 11313 apache 15 0 324m 41m 19m S 48.6 2.1 0:03.23 httpd 11322 apache 16 0 354m 72m 20m R 11.0 3.6 0:05.11 httpd 11322 apache 16 0 354m 72m 20m S 23.9 3.6 0:05.83 httpd 11314 apache 16 0 355m 75m 22m R 18.3 3.7 0:04.64 httpd

  Read the article

• Widespread misinterpretation of DNS rules in resolving wildcards

  - by Dominic Sayers

  [EDITED to add: This problem has gone away on its own. I believe Cloudflare's name resolution may have been to blame. See my own answer below] Here is a snippet of my zone file *.example.com. 300 IN CNAME proxy.herokuapp.com. foo.example.com. 300 IN A 111.111.111.111 If I dig @8.8.8.8 foo.example.com I get the answer I expect: ;; ANSWER SECTION: foo.example.com. 30 IN A 111.111.111.111 The same is true of all other public DNS servers I've tried. However, when I try to set up a check with Pingdom to a URL on foo.example.com it instead sends the traffic to my Heroku app referenced by the *.example.com RR. The same is true of checks set up on New Relic, Errplane and traffic generated by the Heroku app itself. So on the one side, all public DNS servers interpret the zone file one way. Yet four service providers all interpret it a different way, one that differs to the standard suggested by RFC 4592. My question is: are these reputable, mature service providers all wrong? Or is it little me?

  Read the article

• Why can't I get rid of default index.html even if I disable the default virtual host in Apache2?

  - by Emre Sevinç

  I have created a virtual host settings file and I disabled the default settings by using a2dissite default (this is a pretty standard Ubuntu 10.04 installation). But no matter what I try my Apache2 server simply keeps on displaying the default index.html page instead of the index.php page that I set up in the virtual host file. Can someone help me what I'm missing. Details follow: No default settings: ls -l /etc/apache2/sites-enabled/ total 0 lrwxrwxrwx 1 root root 51 May 5 13:32 webmin.1273066327.conf -> /etc/apache2/sites-available/webmin.1273066327.conf lrwxrwxrwx 1 root root 34 May 30 11:03 www.accontax.be -> ../sites-available/www.accontax.be Contents of the relevant virtual host: cat /etc/apache2/sites-enabled/www.accontax.be <VirtualHost *> ServerName www.accontax.be ServerAlias accontax.be DirectoryIndex index.php DocumentRoot /var/www/drupal/ <Directory /var/www/drupal/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> </VirtualHost> Contents of httpd.conf: cat /etc/apache2/httpd.conf Listen 80 NameVirtualHost * I also have those relevant lines in my apache2.conf: # Include generic snippets of statements Include /etc/apache2/conf.d/ # Include the virtual host configurations: Include /etc/apache2/sites-enabled/ When I visit http://www.accontax.be I expect apache2 server go to the /var/www/drupal subdirectory and start serving index.php but it simply keeps on serving index.html from /var/www directory. I have reloaded the configuration, restarted the server, deleted my browser cache. Nothing changed. Probably I'm missing a simple yet crucial step but I just could not find it.

  Read the article

• Restrict SSH user to connection from one machine

  - by Jonathan

  During set-up of a home server (running Kubuntu 10.04), I created an admin user for performing administrative tasks that may require an unmounted home. This user has a home directory on the root partition of the box. The machine has an internet-facing SSH server, and I have restricted the set of users that can connect via SSH, but I would like to restrict it further by making admin only accessible from my laptop (or perhaps only from the local 192.168.1.0/24 range). I currently have only an AllowGroups ssh-users with myself and admin as members of the ssh-users group. What I want is something that works like you may expect this setup to work (but it doesn't): $ groups jonathan ... ssh-users $ groups admin ... ssh-restricted-users $ cat /etc/ssh/sshd_config ... AllowGroups ssh-users [email protected].* ... Is there a way to do this? I have also tried this, but it did not work (admin could still log in remotely): AllowUsers [email protected].* * AllowGroups ssh-users with admin a member of ssh-users. I would also be fine with only allowing admin to log in with a key, and disallowing password logins, but I could find no general setting for sshd; there is a setting that requires root logins to use a key, but not for general users.

  Read the article

• Video output vanishes and it isn't the video card... suggestions?

  - by Ira Baxter

  I have a high-end dual processor Dell workstation that operated for several years without problem. Recently, the video output has gone flaky, in the sense that after 2-3 days, it loses synch with the monitor (sometimes you can still see a hashed-mess of the what you expect to see on the screen). Poking at the keyboard, and accessing the file system on the machine from over the network, indicates that the machine is running fine and its just the video. A reboot fixes the problem... for another day or two. This in effect makes the machine unusable. So, I replaced the video card with an exact duplicate bought from e-bay. (I checked after the dupe arrived to be sure, yep, same model number). I still get the same behavior. So unless I believe that both video cards are broken the same way, I have to beleive this is a problem with the motherboard/power supply, neither of which I am inclined to replace. The only other possibility I can think of is a Windows update to the graphics driver. How would I check for this? Anybody had a similar problem? Otherwise we're junking what used to be a perfectly good machine. (Another couple of hours of more wasted effort and that's it in terms of economics anyway).

  Read the article

• Official end of support date for Internet Explorer 6 on Windows XP

  - by scunliffe

  If I read the docs on Windows Service Pack support policies, and the specific Internet Explorer lifecycle support page as well as the Wikipedia page I've deduced that: IE6 support ends/ended at: Windows 2000 Ended (date unknown) Windows XP SP0 (RTM) Ended Home: 30-Aug-2003 Pro: 30-Sep-2004 SP1 Ended Home: 11-Jul-2004 Pro: 11-Jul-2004 SP2 Home: 13-Jul-2010 Pro: 13-Jul-2010 SP3 (released: April 21, 2008) Home: ??? Pro: ??? What isn't clear is the Windows XP SP3 scenario. In "human" terms, when is the end of support for IE6 on Windows XP SP3? e.g. if there is never a Windows XP SP4... or heaven forbid, an SP4 is released. I realize this doesn't force people to upgrade etc. however I'm trying to get a "semi" official word on when IE6 moves into the "not supported" category. I'm not interested in philosophical answers e.g. "big enterprise won't upgrade but they will expect support into 2017" stuff... I just want the "clear answer" in terms of official Microsoft support.

  Read the article

< Previous Page | 117 118 119 120 121 122 123 124 125 126 127 128  | Next Page >