Search Results

Search found 9244 results on 370 pages for 'thinking sphinx'.

Page 121/370 | < Previous Page | 117 118 119 120 121 122 123 124 125 126 127 128  | Next Page >

• Inexpensive and Open replacement for Cisco Tunnel-based EasyVPN with Cisco VPN 3000 Series

  - by Shoaibi

  I have a scenario when i have to establish peer-to-peer preshared key based VPN to a vendor. This vendor uses Cisco EasyVPN with Cisco VPN 3000 as access concentrator. I check the compatibility of the type of VPN from http://www.cisco.com/en/US/prod/collateral/iosswrel/ps6537/ps6586/ps6635/ps7180/prod_brochure0900aecd80582078.pdf and it appears that it would only work on cisco hardware. I am looking for a less inexpensive and possibly and open replacement to this to save my cost and also recommend to them. I have tried OpenVPN and thinking about vyatta.

  Read the article

• How to know which block device maps to which physical drive

  - by Karolis T.

  I have a server with software RAID 1, two hot-swap sata disks. One hard drive started showing errors, I'm thinking about removing and replacing it, only problem is that I have no idea which of the two correspond to which devices. And I can't shut the server down to find out. I have /dev/sda and /dev/sdb, /dev/sda is the failing one. Thought about doing something along the lines # mdadm --manage /dev/md0 --remove /dev/sda1 then somehow stop/suspend the drive using tuning software and try to listen which of the two stopped, but that's not gonna work in a noisy server environment. Drive panels have no LEDs. Thanks for any ideas!

  Read the article

• On Server Disk Storage VS SAN Storage

  - by Justin

  Hello, I am looking at buying three servers, and trying to figure out which storage solution makes the most sense in terms of performance and cost. Total budget is around: $10,000. OPTION 1: Dell servers with RAID 10 (4 Drives) each 7200RPM SAS 500GB, for a total capacity of 1TB. Each server is approx: $3000. Total storage then across all three servers is 3TB. OPTION 2: Same Dell servers with a cheap single drive no RAID for $2000 and go with a centralized SAN solution. The biggest problem is that I haven't been able to even find a SAN solution that is a reasonable price. Dell entry level storage servers are like $15,000. I am thinking just iSCSI, not fiber (too expensive). What do you guys recommend?

  Read the article

• Configuring and managing Windows web server

  - by Mike C.

  Hello, I run a few websites and I was thinking of paying for a dedicated Windows web server from GoDaddy instead of paying for each site's hosting individually. I know enough about IIS to configure the Host Header and stuff like that, but I'm a little fuzzy about the email portion of the hosting. I have a few questions: Do I need to install an SMTP server on the web server to allow for emails to be sent/received to a website email address? Or is there another approach that I'm unaware of? Are there tools that monitor the amount of bandwidth used by the server? GoDaddy charges for bandwidth and I want to make sure I don't go over. Am I opening a can of worms that I don't really want to open by going the dedicated server route? Things like server updates, security, etc? Thanks!

  Read the article

• vmware server end of life, where to go now?

  - by matnagel

  We have some virtual machines on vmware server 2.x running on 64 bit hardware and quite happy with it. As vmware server will no longer be offered we are thinking to migrate to ESXi, which seems is free. We will have to install the specialized network cards but that's a minor problem. But once left alone with a quite silently discontinued product there is some resistance to vmware. VirtualBox seems to work: http://blogs.oracle.com/virtualization/2010/06/migrating_from_vmware_to_virtu.html What other free (of licencing cost) options are there? We have windows server 2003 32 bit VMs and also linux 32 and 64 bit VMs to migrate. So xen does not seem an option, which does not run microsoft OSes.

  Read the article

• Migrating to OSGi?

  - by Paul McKenzie

  We're currently running server-side java apps on windows using JavaServiceWrapper and this has been a good solution for us. We have a small number of Spring-based lightweight applications. But now we need to look at introducing some modularity into our services. To that end I have been thinking about OSGi. I need to know which OSGi containers are ready for prime-time production use in a medium-ish load environment? Eclipse Equinox 3.5.xKnopflerfish 3.xApache Felix 2.xAnything else?

  Read the article

• Torrents: Can I protect my software by sending wrong bytes?

  - by martijn-courteaux

  Hi, It's a topic that everyone interests. How can I protect my software against stealing, hacking, reverse engineering? I was thinking: Do my best to protect the program for reverse engineering. Then people will crack it and seed it with torrents. Then I download my own cracked software with a torrent with my own torrent-software. My own torrent-software has then to seed incorrect data (bytes). Of course it has to seed critical bytes. So people who want to steal my software download my wrong bytes. Just that bytes that are important to startup, saving and loading data, etc... So if the stealer download from me (and seed it later) can't do anything with it, because it is broken. Is this idea relevant? Maybe, good torrent-clients check hashes from more peers to check if the packages (containing my broken bytes) I want to seed are correct or not? Thanks

  Read the article

• Dedicated server configuration - some tips -Xenserver/Debian

  - by Sanjay S

  I am migrating from a vps based hosting to a dedicated hosting (8GB RAM/1TB HD). I need to run multiple Drupal and Ruby based applications? what would be the recommended configuration. I was thinking of two options. 1) Install multiple Debian os on top of Xen (like VPS). Each may be 2GB Memory and run Drupal and Ruby and MYSQL on separate partitions . 2) Install one instance of Debian. and Install Drupal (Apache, php) Ruby (lighttpd, ruby) ,MySQL all in the same partition I was little worried that option 2 could lead to some performance issues later..

  Read the article

• Best practice for authenticating DMZ against AD in LAN

  - by Sergei

  We have few customer facing servers in DMZ that also have user accounts , all accounts are in shadow password file. I am trying to consolidate user logons and thinking about letting LAN users to authenticate against Active Directory.Services needing authentication are Apache, Proftpd and ssh. After consulting security team I have setup authentication DMZ that has LDAPS proxy that in turn contacts another LDAPS proxy (proxy2) in LAN and this one passes authentication info via LDAP (as LDAP bind) to AD controller.Second LDAP proxy only needed because AD server refuses speak TLS with our secure LDAP implemetation. This works for Apache using appropriate module.At a later stage I may try to move customer accounts from servers to LDAP proxy so they are not scattered around servers. For SSH I joined proxy2 to Windows domain so users can logon using their windows credentials.Then I created ssh keys and copied them to DMZ servers using ssh-copy, to enable passwordless logon once users are authenticated. Is this a good way to implement this kind of SSO?Did I miss any security issues here or maybe there is a better way ofachieving my goal?

  Read the article

• Roundcube access from outside local network

  - by Mike K

  I have setup hmailserver on a windows xp pro computer and everything is working great when it comes to getting it to send and receive email. Now here is where my problem comes in... I have setup roundcube using uniserver and everything works great internally. Now, what I am trying to do is to be able to access roundcube from the internet outside of the local network. I have opened up ports 80, 443, and the mysql port yet I am still unable to access this from outside of the network. The error message that I am getting is as followed: Forbidden You don't have permission to access /webmail/ on this server. Additionally, a 404 Not Found error was encountered while trying to use an ErrorDocument to handle the request. I believe something needs to be edited in the apache config file. Any help would be greatly appreciated. I am hoping I dont need to run this on windows server but I'm kinda losing hope and thinking I will need to because I need IIS.

  Read the article

• Virtual memory on Linux doesn't add up?

  - by Brendan Long

  I was looking at System Monitor on Linux and noticed that Firefox is using 441 MB of memory, and several other applications are using 274, 257, 232, etc (adding up to over 3 GB of virtual memory). So I switch over to the Resources tab, and it says I'm using 462 MB of memory and not touching swap. I'm confused. What does the virtual memory amount mean then if the programs aren't actually using it. I was thinking maybe memory they've requested but aren't using, but how would the OS know that? I can't think of any "I might need this much memory in the future" function..

  Read the article

• Autoscale Rackspace Cloud, Scalr or DIY?

  - by Andre Jay Marcelo-Tanner

  I'm looking into creating a setup on Rackspace Cloud that will allow me to autoscale my webservers (no db) on demand. Preferably using something like response time. I've read into configuration tools like Puppet/Chef, but I'm thinking I can just launch from prepared server images that are ready to go. Is there any tool out there already that can monitor my existing node response times and then launch or scale up new ones based upon certain variables like average X load over Y time? I see there are commercial offerings like Scalr, Rightscale, but how would I do this myself?

  Read the article

• Can I issue wireless clients with IP address on different subnet?

  - by Beanz

  We have a very standard setup with a Windows Server 2003 domain controller issuing IP addresses using DHCP. This works fine. Internet access is managed via Microsoft ISA Server 2006 Standard. Clients are required to authenticate and this works fine. We now need to provide wireless internet access to visitors for laptops, iPhones etc. We've bought a couple of Netgear access points so I was thinking we might be able to issue wireless clients connected to it with an IP address on a different subnet and then allow non-authenticated Internet access via the ISA Server for that IP range. Does that sound plausible? I'm not even sure if I can issue a different subnet to wireless clients.

  Read the article

• UPS and power strip interactions?

  - by chaos

  Sometimes I hear that you shouldn't plug (UPS brand X / any UPS) into (power strip brand X / any power strip) because of some interaction leading to poorly conditioned power, reduced battery life, massive explosions spattering the room with battery acid, and so on. Sometimes I hear that it's the power strip that you shouldn't plug into the UPS. What I haven't gotten is a clear idea of how reliable these recommendations are or how generally/specifically they apply. Can anyone speak precisely and non-urban-legendfully on these UPS and power strip interactions, if there are in fact ones worth thinking about?

  Read the article

• Overhead of Perfmon -> direct to SQL Database

  - by StuartC

  HI All, First up, I'm a total newb at Performance Monitoring. I'm looking to set up central performance monitoring of some boxes. 2K3 TS ( Monitor General OS Perf & Session Specific Counters ) 2K8 R2 ( XenApp 6 = Monitor General OS Perf & Session Specific Counters ) File Server ( Standard File I/O ) My ultimate aim is to get as many counters/information, without impacting the clients session experience at all. Including counters specific to their sessions. I was thinking it logging directly to a SQL on another server, instead of a two part process of blg file then relog to sql. Would that work ok? Does anyone know the overhead of going straight to SQL from the client? I've searched around a bit, but havent found so much information it can be overwhelming. thanks

  Read the article

• Does MS Forefront TMG cache authentication?

  - by SnOrfus

  I'm testing a client machine that makes requests to a biztalk server using a forefront machine as a web proxy. Upon first test I put in an invalid name/password into the receive port and received the correct error message (407). Then, I set the correct name/password and everything worked correctly. From there, I kept the correct information in the receive port but put an invalid name/password into the send adapter but the process completed successfully (should have failed with 407). I've ensured that both the recieve and send ports are not bypassing the proxy for local addresses. So the only thing that seems to make sense is if TMG is caching the authentication request coming from the machine I'm working on. Is this thinking correct, and if so, does anyone know how to disable it in TMG?

  Read the article

• Quickest way to run IISRESET as administrator

  - by Chris Adams

  Trying to optimize my day here, making do with IIS... When executing IISRESET from the Run dialog or from cmd.exe, I get an access denied error. So executing IISRESET gets annoying - involving both mouse and keyboard: Start - Run - cmd (right-click, Run as Administrator) Agree to the UAC dialog Type iisreset, hit enter I'm looking to be able to run IISRESET as quickly as possible. Ideally I could just go Start - Run - iisreset - Enter, and the UAC prompt would pop up. I tried to enable "Run this program as an Administrator" but it was greyed out, even when I opened the properties dialog as NT AUTHORITY\SYSTEM. Thinking of making a Visual Studio macro and a toolbar button; anyone got any other ideas?

  Read the article

• Scheduled task to map a network drive runs, but doesn't map the drive

  - by bikefixxer

  I have a task set up to run whenever the computer is logged onto that deletes all network folders and maps a network drive. Here is what is in the batch file: @echo off net use * /delete /y net use b: \\Server\Share /user:DOMAIN\Username password exit When the computer is restarted or logged off and back on, the task runs fine (according to the scheduled tasks window saying when it ran last) but the mapped drive doesn't show up. I'll open the command prompt and type "net use" and it simply says "There are no entries in the list". If I then right click on the task and run it, it works and the mapped drive shows up. I've checked the log and nothing shows up. I've tried adding a timer in the batch file so it waits 10 seconds (ping 1.1.1.1 -n 1 -w 10000nul) thinking that maybe the network wasn't connected, but that didn't work. What else can I try? Thanks!

  Read the article

• VirtualBox Mac - Is it possible re-map a key for a VM

  - by Erin Drummond

  I am running Windows inside VirtualBox on Mac OSX. However, I am frequently copying and pasting/undoing etc using keyboard shortcuts. Because Mac is dumb and tries to be different, common shortcuts such as ctrl+c and ctrl+v are cmd+c and cmd+v on Mac. This creates a problem because I keep trying to use mac-style shortcuts in the VM, or windows-style shortcuts on the Mac (my workflow is, do ASP.NET dev in the VM, but use the Mac hosts browser). What I would like to be able to do is make VirtualBox send "Command" key presses as "Ctrl" to the VM, so that I dont have to keep remembering which environment I am in and thinking about which key combination I need to use. Is this possible?

  Read the article

• How to fix skipping/stuttering audio in Google Chrome

  - by Droid

  If I play Google Music, or a Youtube video in the Chrome browser, and then open a new tab and start typing the address bar, the audio will quickly cut in and out as I am typing (with almost every letter I type). It also is choppy if I play the video and start typing in the start menu. I can not repeat this behavior using internet explorer. Based on that Im thinking that it maybe a problem with the version of flash Chrome is using but I'm not sure. Any ideas? Im running 32 bit windows 7, i.e. 9, and chrome 23.0 pc is a lenovo t43p. I have the latest sound drivers. i.e. is using flash 11.5.502. chrome is using : Adobe Flash Player - Version: 11.5.31.2 Only one (this) plugin is listed for flash in the chrome plugins list.

  Read the article

• NAS + XBMC combination

  - by Hendrik

  I currently own a WD Sharespace and I am not too happy about it. It will freeze constantly and its rather slow. I've been thinking of replacing it. I also own a WD HD Live, and it works like it is supposed to, but recently I've seen XBMC in action and I was quite impressed. I've been wondering lately about the possibility of replacing both products with one new device: a fast reliable nas which I can install XBMC on and is capable of rendering video and has an HDMI out. Do any such devices exist for sale or is the only way to build one from scratch? I've seen HTPC's for sale but I've never seen any of them with a raid setup. I've also read about building your own NAS with freeNAS but those setups dont allow you to run XBMC. Does anyone have experience with this?

  Read the article

• How do I reset the time on my computer, without turning it on?

  - by chipperyman573

  Alright, so today, I did something very stupid: Do an experement on my computer without backing it up. So I saw that the calander in windows could only go up to 12/31/2999 (or something like that). I was wondering if I set the time to 11:59:59 PM, if it would crash my computer, thinking that if I did I could just restart it from the recovery disc or something. Well, I was right: It did crash it. However, I can't turn my computer on AT ALL. When I try to, it plays a 1-2 second beep, 1 second silence, repeated a total of 3 times. My manufacturer is Dell. I'm sending this from my phone, I appolgise for all typos. My last backup was from a few months ago, that won't work.

  Read the article

• Launch an arbitrary application with a specific icon

  - by Camilo Martin

  I'm thinking about customizing my Windows 7's application icons, so that they all follow a specific theme (Token-like icons). This would involve using Resource Hacker (or similar) to patch each .exe. Not only this would be tiresome, but also it would require doing it again at each update of each application (nevermind that some could break just because it was tampered with). Instead, is there any way to launch an application with a specific icon? Ideally it would be something from the command-line (so I can make a shortcut), like this: launchwithicon.exe --app C:\myapp.exe --icon C:\myicon.ico Note that while it is possible to do something similar by setting the taskbar to "always combine, hide labels", I do not like this approach and instead am looking for something that works without combining the taskbar icons.

  Read the article

• Can I upgrade my Soltek sl-67a-c motherboard from Pentium II to Pentium III?

  - by jedatu

  I have a Pentium III processor and I thought I would replace the Pentium II on my Soltek SL-67A-C. The motherboard has Slot 1 so the PIII fits in fine, however, when I turn on the computer the bios does not come up. Here's the link to some specs on the board: http://stason.org/TULARC/pc/motherboards/F/FLASH-TECH-INC-Pentium-II-Deschutes-SL-67A-C.html I know that I updated the bios at one time. I see references to a "67af3.zip" bios upgrade file out there but can't find any source to download it. I am thinking I may have to adjust the jumpers on the motherboard to match the speed of the processor, but I am not sure how to go about that. Any suggestions?

  Read the article

• How do you recommend installing Linux on a computer that has no external drive or ability to boot fr

  - by 7777

  I have an old Toshiba Portege 3505 "ultralight" laptop, meaning it doesn't have any kind of disk drive on it at all, that I'd like to completely reformat and install Linux on. However, it won't boot from any drive (and I don't have any on hand), so I'll have to install it from a USB drive (which I doubt it boots from either). (I'm not sure how to change the settings in my BIOS to get my computer to boot from a USB stick. Any ideas for this?) How do you recommend I do this? I want to note that I don't want to run Linux off a LiveUSB, I want to actually install it on the machine. I was thinking about Damn Small Linux, it's tiny and all I need. Any advice or suggestions for something else though? Finally, I'm a total newbie to this, I've never installed Linux on anything before so I might be a little slow on some stuff! Thanks!

  Read the article

< Previous Page | 117 118 119 120 121 122 123 124 125 126 127 128  | Next Page >