Search Results

Search found 16894 results on 676 pages for 'block device'.

Page 123/676 | < Previous Page | 119 120 121 122 123 124 125 126 127 128 129 130  | Next Page >

• How can a usb be detected but not show up anywhere?

  - by George Mauer

  I started the morning by trying to create a bootable usb using a 2gb stick and the startup disk creator. It seemed to run through the whole process just fine until it got to a screen that read something like "Creating memory partion" and which sat on 100% for about 45 minutes before I hit cancel and removed the usb stick. Now the usb stick is not being detected as storage or...anything (even on my windows pc) though it does show up in the syslog. Allow me to demonstrate. We start with the usb not plugged in: [georgemauer@ubuntu:~]$ sudo fdisk -l (04-04 16:01) Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x994bdc0f Device Boot Start End Blocks Id System /dev/sda1 2048 27650047 13824000 27 Hidden NTFS WinRE /dev/sda2 * 27650048 27854847 102400 7 HPFS/NTFS/exFAT /dev/sda3 27854848 976771119 474458136 7 HPFS/NTFS/exFAT I plug in the usb: [georgemauer@ubuntu:~]$ tail -f /var/log/syslog ***Snip*** Apr 4 15:01:18 ubuntu wpa_supplicant[1136]: WPA: Group rekeying completed with 00:24:36:ad:e7:3f [GTK=TKIP] Apr 4 15:02:29 wpa_supplicant[1136]: last message repeated 3 times Apr 4 15:02:29 ubuntu kernel: [22122.788133] usb 2-1: new high speed USB device number 13 using ehci_hcd Apr 4 15:02:29 ubuntu kernel: [22122.923873] scsi10 : usb-storage 2-1:1.0 Apr 4 15:02:29 ubuntu mtp-probe: checking bus 2, device 13: "/sys/devices/pci0000:00/0000:00:13.2/usb2/2-1" Apr 4 15:02:30 ubuntu mtp-probe: bus: 2, device: 13 was not an MTP device Apr 4 15:02:30 ubuntu kernel: [22123.926154] scsi 10:0:0:0: Direct-Access GENERIC USB Mass Storage 1.00 PQ: 0 ANSI: 2 Apr 4 15:02:30 ubuntu kernel: [22124.105118] sd 10:0:0:0: Attached scsi generic sg1 type 0 Apr 4 15:02:30 ubuntu kernel: [22124.108212] sd 10:0:0:0: [sdb] Attached SCSI removable disk but then: [georgemauer@ubuntu:~]$ ls /mnt -alF (04-04 16:02) total 8 drwxr-xr-x 2 root root 4096 2011-04-21 12:51 ./ drwxr-xr-x 26 root root 4096 2012-03-31 13:16 ../ [georgemauer@ubuntu:~]$ ls /media -alF (04-04 16:03) total 8 drwxr-xr-x 2 root root 4096 2012-04-04 12:18 ./ drwxr-xr-x 26 root root 4096 2012-03-31 13:16 ../ What could be going on and how do I recover my usb key?

  Read the article

• Pygame: Save a list of objects/classes/surfaces

  - by Sam Tubb

  I am working on a game, in which you can create mazes. You place blocks on a 16x16 grid, while choosing from a variety of block to make the level with. Whenever you create a block, it adds this class: class Block(object): def __init__(self,x,y,spr): self.x=x self.y=y self.sprite=spr self.rect=self.sprite.get_rect(x=self.x,y=self.y) to a list called instances. I tried shelving it to a .bin file, but it returns some error dealing with surfaces. How can I go about saving and loading levels? Any help is appreciated! :) Here is the whole code for reference: import pygame from pygame.locals import * #initstuff pygame.init() screen=pygame.display.set_mode((640,480)) pygame.display.set_caption('PiMaze') instances=[] #loadsprites menuspr=pygame.image.load('images/menu.png').convert() b1spr=pygame.image.load('images/b1.png').convert() b2spr=pygame.image.load('images/b2.png').convert() currentbspr=b1spr curspr=pygame.image.load('images/curs.png').convert() curspr.set_colorkey((0,255,0)) #menu menuspr.set_alpha(185) menurect=menuspr.get_rect(x=-260,y=4) class MenuItem(object): def __init__(self,pos,spr): self.x=pos[0] self.y=pos[1] self.sprite=spr self.pos=(self.x,self.y) self.rect=self.sprite.get_rect(x=self.x,y=self.y) class Block(object): def __init__(self,x,y,spr): self.x=x self.y=y self.sprite=spr self.rect=self.sprite.get_rect(x=self.x,y=self.y) while True: #menu items b1menu=b1spr.get_rect(x=menurect.left+32,y=48) b2menu=b2spr.get_rect(x=menurect.left+64,y=48) menuitems=[MenuItem(b1menu,b1spr),MenuItem(b2menu,b2spr)] screen.fill((20,30,85)) mse=pygame.mouse.get_pos() key=pygame.key.get_pressed() placepos=((mse[0]/16)*16,(mse[1]/16)*16) if key[K_q]: if mse[0]<260: if menurect.right<255: menurect.right+=1 else: if menurect.left>-260: menurect.left-=1 else: if menurect.left>-260: menurect.left-=1 for e in pygame.event.get(): if e.type==QUIT: exit() if menurect.right<100: if e.type==MOUSEBUTTONUP: if e.button==1: to_remove = [i for i in instances if i.rect.collidepoint(placepos)] for i in to_remove: instances.remove(i) if not to_remove: instances.append(Block(placepos[0],placepos[1],currentbspr)) for i in instances: screen.blit(i.sprite,i.rect) if not key[K_q]: screen.blit(curspr,placepos) screen.blit(menuspr,menurect) for item in menuitems: screen.blit(item.sprite,item.pos) if item.rect.collidepoint(mse): if pygame.mouse.get_pressed()==(1,0,0): currentbspr=item.sprite pygame.draw.rect(screen, ((255,0,0)), item, 1) pygame.display.flip()

  Read the article

• Windows XP Home Edition SP3 cant recognise PCMIA SD Card

  - by Pozo

  System Specifications: Laptop : Dell Inspiron 6000 OS: Windows Home Edition SP3 SD Adapter: Hagiwara Smart Media Adapter I inserted the card into the slot, windows xp recognises the device, lists the pcmia controller on the device manager list, an entry appears under the IDE ATA/ATAPI category on the device manager as well. However, the device does not show under my computer and the driver does not get assigned a letter number. I checked the system logs from the device manager and there were no logged errors. Checking the Hagiwara support website, the manufacturer indicates that the adapter driver is the same as the windows xp pcmia controller. Checking Dell's website, no specific drivers were listed for that either. General Search on the web indicates that multiple people face similar problems with their SD cards, yet none actually spell out the route issue that causes this. Please let me know if you have any suggestions for further debugging. Thanks in advance

  Read the article

• Collision detection, stop gravity

  - by Scott Beeson

  I just started using Gamemaker Studio and so far it seems fairly intuitive. However, I set a room to "Room is Physics World" and set gravity to 10. I then enabled physics on my player object and created a block object to match a platform on my background sprite. I set up a Collision Detection event for the player and the block objects that sets the gravity to 0 (and even sets the vspeed to 0). I also put a notification in the collision event and I don't get that either. I have my key down and key up events working well, moving the player left and right and changing the sprites appropriately, so I think I understand the event system. I must just be missing something simple with the physics. I've tried making both and neither of the objects "solid". Pretty frustrating since it looks so easy. The player starting point is directly above the block object in the grid and the player does fall through the block. I even made the block sprite solid red so I could see it (initially it was invisible, obviously).

  Read the article

• Can I get the Waves Maxx speaker effects to work in Ubuntu?

  - by Rafael

  I have a new machine that comes with JBL 2.1 Speakers with Waves Maxx Audio 3. On Windows it sounds perfect, though in Ubuntu 12.04 I get cheap/sound with simple mp3 files. I have tried a few things on different blogs but no luck so far. Any ideas? aplay -l **** List of PLAYBACK Hardware Devices **** card 0: PCH [HDA Intel PCH], device 0: ALC665 Analog [ALC665 Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: PCH [HDA Intel PCH], device 1: ALC665 Digital [ALC665 Digital] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: PCH [HDA Intel PCH], device 3: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: N700 [Logitech Speaker Lapdesk N700], device 0: USB Audio [USB Audio] Subdevices: 1/1 Subdevice #0: subdevice #0

  Read the article

• Cheap sound on speakers - Dell XPS L502X

  - by Rafael

  I have a new machine that comes with JBL 2.1 Speakers with Waves Maxx Audio 3. On Windows it sounds perfect, though in Ubuntu 12.04 I get cheap/sound with simple mp3 files. I have tried a few things on different blogs but no luck so far. Any ideas? aplay -l **** List of PLAYBACK Hardware Devices **** card 0: PCH [HDA Intel PCH], device 0: ALC665 Analog [ALC665 Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: PCH [HDA Intel PCH], device 1: ALC665 Digital [ALC665 Digital] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: PCH [HDA Intel PCH], device 3: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: N700 [Logitech Speaker Lapdesk N700], device 0: USB Audio [USB Audio] Subdevices: 1/1 Subdevice #0: subdevice #0

  Read the article

• I can't change audio/volume preferences?

  - by genesis

  When I click to sound icon on the panel, I have 3 options: "Mute all" is gray and could not be clicked Slider - I can slide but it DOESNT change anything Preferences - Shows this (waiting for the response from audio device), but it doesn't show anything for more than a hour This is from aplay -l : root@fb:~# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: SB [HDA ATI SB], device 0: ALC272 Analog [ALC272 Analog] Subdevices: 1/1 Subdevices #0: subdevice #0 karta 1: HDMI [HDA ATI HDMI], device 3: ATI HDMI [ATI HDMI] Subdevices: 1/1 Subdevices #0: subdevice #0 root@fb:~# What's wrong?

  Read the article

• Windows Phone 8 Music sync

  - by Damian Smilgin

  I've tried to sync my music between my lumia 920 and ubuntu 13.10/14.04. When I copy/paste files into my device nothing happens. My device thinks there is no music at all. When i sync music by rhythmbox my music player see the music, but not album/artists. When I sync by qlix/gmtp there is information about album, album cover but no artist again. How to put music with all mp3 tags on Windows Phone 8 device?

  Read the article

• Should Exterrnal USB hard drive auto mount Ubuntu 12.04.01 LTS

  - by Chris Good

  I want to have external USB hard drives automatically mounted when plugged in. I have 2 drives exactly the same except for volume label. They both have the same UUID. I want to be easily able to swap them as I'm using them for backups and want to keep 1 at home for off site backup. I've set up the /etc/fstab so they should mount at different places based on their volume label: /etc/fstab : LABEL=Passport1 /media/Passport1 ntfs defaults,windows_names,locale=en_US.utf8 0 0 LABEL=Passport2 /media/Passport2 ntfs defaults,windows_names,locale=en_US.utf8 0 0 blkid shows : ... /dev/sdc1: LABEL="Passport2" UUID="4E1AEA7B1AEA6007" TYPE="ntfs" /dev/sdd1: LABEL="Passport1" UUID="4E1AEA7B1AEA6007" TYPE="ntfs" They both mount automatically during reboot but do not mount when just plugged in to a running system. I've read lots of stuff about this, much of it is old so I'm not sure if it applies. I've read some stuff that says the mounts should happen automatically when plugged in, and lots of other stuff that says you have to install other software to make this happen, although much of it just seems to set up the fstab. What's the real story? Here is /var/log/syslog when drive is plugged in: Dec 14 11:22:58 ausyvutims1 kernel: [66221.300196] usb 1-1: new high-speed USB device number 6 using ehci_hcd Dec 14 11:22:58 ausyvutims1 mtp-probe: checking bus 1, device 6: "/sys/devices/pci0000:00/0000:00:11.0/0000:02:03.0/usb1/1-1" Dec 14 11:22:58 ausyvutims1 mtp-probe: bus: 1, device: 6 was not an MTP device Dec 14 11:22:58 ausyvutims1 kernel: [66221.656020] scsi7 : usb-storage 1-1:1.0 Dec 14 11:22:59 ausyvutims1 kernel: [66222.661534] scsi 7:0:0:0: Direct-Access WD My Passport 0748 1016 PQ: 0 ANSI: 6 Dec 14 11:22:59 ausyvutims1 kernel: [66222.666466] scsi 7:0:0:1: Enclosure WD SES Device 1016 PQ: 0 ANSI: 6 Dec 14 11:22:59 ausyvutims1 kernel: [66222.667739] sd 7:0:0:0: Attached scsi generic sg3 type 0 Dec 14 11:22:59 ausyvutims1 kernel: [66222.667913] ses 7:0:0:1: Attached Enclosure device Dec 14 11:22:59 ausyvutims1 kernel: [66222.668047] ses 7:0:0:1: Attached scsi generic sg4 type 13 Dec 14 11:22:59 ausyvutims1 kernel: [66222.678473] sd 7:0:0:0: [sdc] 1953458176 512-byte logical blocks: (1.00 TB/931 GiB) Dec 14 11:22:59 ausyvutims1 kernel: [66222.687700] sd 7:0:0:0: [sdc] Write Protect is off Dec 14 11:22:59 ausyvutims1 kernel: [66222.687705] sd 7:0:0:0: [sdc] Mode Sense: 47 00 10 08 Dec 14 11:22:59 ausyvutims1 kernel: [66222.701076] sd 7:0:0:0: [sdc] No Caching mode page present Dec 14 11:22:59 ausyvutims1 kernel: [66222.701081] sd 7:0:0:0: [sdc] Assuming drive cache: write through Dec 14 11:22:59 ausyvutims1 kernel: [66222.738062] sd 7:0:0:0: [sdc] No Caching mode page present Dec 14 11:22:59 ausyvutims1 kernel: [66222.738068] sd 7:0:0:0: [sdc] Assuming drive cache: write through Dec 14 11:22:59 ausyvutims1 kernel: [66222.754558] sdc: sdc1 Dec 14 11:22:59 ausyvutims1 kernel: [66222.792006] sd 7:0:0:0: [sdc] No Caching mode page present Dec 14 11:22:59 ausyvutims1 kernel: [66222.792012] sd 7:0:0:0: [sdc] Assuming drive cache: write through Dec 14 11:22:59 ausyvutims1 kernel: [66222.792016] sd 7:0:0:0: [sdc] Attached SCSI disk Dec 14 11:22:59 ausyvutims1 ata_id[16971]: HDIO_GET_IDENTITY failed for '/dev/sdc': Invalid argument Thanks for any help offered

  Read the article

• Only One GPU Detected in the Nvidia Quadro NVS 450

  - by Kyle Brandt

  I just built myself an new workstation and now only 2 of 3 monitors are working. I built the nvidia driver by downloading it and installing with ./Nvidia... Before when I ran nvidia-settings I saw two GPUs listed but now I only see one. Xorg Config (Not sure how I ended up with 3 devices in there): # nvidia-settings: X configuration file generated by nvidia-settings # nvidia-settings: version 256.35 (buildmeister@builder101) Wed Jun 16 19:25:39 PDT 2010 Section "ServerLayout" # Removed Option "Xinerama" "1" Identifier "Layout0" Screen 0 "Screen0" 0 0 Screen 1 "Screen1" RightOf "Screen0" InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" Option "Xinerama" "0" EndSection Section "Files" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor0" VendorName "Unknown" ModelName "DELL E207WFP" HorizSync 30.0 - 83.0 VertRefresh 56.0 - 75.0 Option "DPMS" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor1" VendorName "Unknown" ModelName "DELL E207WFP" HorizSync 30.0 - 83.0 VertRefresh 56.0 - 75.0 Option "DPMS" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor2" VendorName "Unknown" ModelName "DELL E207WFP" HorizSync 30.0 - 83.0 VertRefresh 56.0 - 75.0 Option "DPMS" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro NVS 450" BusID "PCI:6:0:0" EndSection Section "Device" Identifier "Device1" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro NVS 450" BusID "PCI:5:0:0" EndSection Section "Device" Identifier "Device2" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro NVS 450" BusID "PCI:3:0:0" EndSection Section "Screen" # Removed Option "TwinView" "0" # Removed Option "metamodes" "DFP-0: nvidia-auto-select +0+0" # Removed Option "metamodes" "DFP-0: nvidia-auto-select +0+275, DFP-3: nvidia-auto-select +1680+0" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "TwinView" "1" Option "TwinViewXineramaInfoOrder" "DFP-3" Option "metamodes" "DFP-0: nvidia-auto-select +0+0, DFP-3: nvidia-auto-select +1680+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" # Removed Option "metamodes" "DFP-3: nvidia-auto-select +0+0" Identifier "Screen1" Device "Device1" Monitor "Monitor1" DefaultDepth 24 Option "TwinView" "0" Option "metamodes" "nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Identifier "Screen2" Device "Device2" Monitor "Monitor2" DefaultDepth 24 Option "TwinView" "0" Option "metamodes" "nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection lscpi: 00:00.0 Host bridge: Intel Corporation 5520/5500/X58 I/O Hub to ESI Port (rev 13) 00:01.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 1 (rev 13) 00:02.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 2 (rev 13) 00:03.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 3 (rev 13) 00:10.0 PIC: Intel Corporation 5520/5500/X58 Physical and Link Layer Registers Port 0 (rev 13) 00:10.1 PIC: Intel Corporation 5520/5500/X58 Routing and Protocol Layer Registers Port 0 (rev 13) 00:11.0 PIC: Intel Corporation 5520/5500 Physical and Link Layer Registers Port 1 (rev 13) 00:11.1 PIC: Intel Corporation 5520/5500 Routing & Protocol Layer Register Port 1 (rev 13) 00:13.0 PIC: Intel Corporation 5520/5500/X58 I/O Hub I/OxAPIC Interrupt Controller (rev 13) 00:14.0 PIC: Intel Corporation 5520/5500/X58 I/O Hub System Management Registers (rev 13) 00:14.1 PIC: Intel Corporation 5520/5500/X58 I/O Hub GPIO and Scratch Pad Registers (rev 13) 00:14.2 PIC: Intel Corporation 5520/5500/X58 I/O Hub Control Status and RAS Registers (rev 13) 00:15.0 PIC: Intel Corporation 5520/5500/X58 Trusted Execution Technology Registers (rev 13) 00:1a.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 00:1a.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 00:1a.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 00:1a.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 00:1b.0 Audio device: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller 00:1c.0 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 1 00:1c.1 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 2 00:1c.3 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 4 00:1c.4 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 5 00:1d.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 00:1d.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 00:1d.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 00:1d.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90) 00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller 00:1f.2 IDE interface: Intel Corporation 82801JI (ICH10 Family) 4 port SATA IDE Controller #1 00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller 00:1f.5 IDE interface: Intel Corporation 82801JI (ICH10 Family) 2 port SATA IDE Controller #2 01:00.0 IDE interface: Device 1b4b:91a3 (rev 11) 02:00.0 USB Controller: NEC Corporation Device 0194 (rev 03) 03:00.0 PCI bridge: nVidia Corporation PCI express bridge for Quadro Plex S4 / Tesla S870 / Tesla S1070 (rev a3) 04:00.0 PCI bridge: nVidia Corporation PCI express bridge for Quadro Plex S4 / Tesla S870 / Tesla S1070 (rev a3) 04:02.0 PCI bridge: nVidia Corporation PCI express bridge for Quadro Plex S4 / Tesla S870 / Tesla S1070 (rev a3) 05:00.0 3D controller: nVidia Corporation G98 [Quadro NVS 450] (rev a1) 06:00.0 VGA compatible controller: nVidia Corporation G98 [Quadro NVS 450] (rev a1) 08:00.0 SATA controller: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 02) 08:00.1 IDE interface: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 02) 09:00.0 SATA controller: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 03) 09:00.1 IDE interface: JMicron Technology Corp. JMB362/JMB363 Serial ATA Controller (rev 03) 0a:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) 0b:06.0 FireWire (IEEE 1394): Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link)

  Read the article

• How to associate hardware volume control to USB speakers?

  - by Wolfger

  My Xubuntu system recognizes my speakers, and I can change the mixer settings to make them the active sound device, but no matter what I do, the hardware dial will only affect the onboard sound device. generic-usb 0003:046D:0A19.0003: input,hidraw1: USB HID v1.00 Device [ Logitech Logitech Z205 ] on usb-0000:00:1d.1-1/input2 updated to reflect the fact that this was Xubuntu desktop (from Kubuntu install originally) where I had this problem. I was able to easily do this from Ubuntu Natty installation.

  Read the article

• How do I configure WakeOnUSB properly?

  - by wishi

  How do I configure Wake-On-USB properly on a 10.04 or 10.10 Ubuntu (2.6.36 and higher if needed)? (Wake-on-USB is when the computer is asleep and for example a USB Keyboard event wakes up the machine!) The notebook is an Acer Aspire Timeline X 1830T. I don't know in which way the Linux Kernel supports the controllers. There are different ways to approach this, for example /proc/acpi/wakeup... or UDEV... or something with HAL? /proc/acpi/wakeup shows every device in S4, but I need S3. Device S-state Status Sysfs node P0P2 S4 *disabled PEGP S4 *disabled P0P1 S0 *disabled pci:0000:00:1e.0 EHC1 S4 *disabled pci:0000:00:1d.0 USB1 S4 *enabled USB2 S4 *disabled USB3 S4 *disabled USB4 S4 *disabled EHC2 S4 *disabled pci:0000:00:1a.0 USB5 S4 *disabled USB6 S4 *disabled USB7 S4 *disabled HDEF S0 *disabled pci:0000:00:1b.0 RP01 S5 *disabled pci:0000:00:1c.0 PXSX S5 *disabled pci:0000:01:00.0 RP02 S0 *disabled pci:0000:00:1c.1 PXSX S5 *disabled pci:0000:02:00.0 RP03 S0 *disabled PXSX S5 *disabled RP04 S0 *disabled PXSX S5 *disabled RP05 S0 *disabled PXSX S5 *disabled RP07 S0 *disabled PXSX S5 *disabled RP08 S0 *disabled PXSX S5 *disabled GLAN S0 *disabled PEG3 S4 *disabled PEG5 S4 *disabled PEG6 S4 *disabled SLPB S3 *enabled S4, which is Suspend-To-Disk afaik... doesn't seem to work either if I echo USB1 into the wakeup table. It just sets an S4 flag. can I get the USB ports in S3? I want to make the machine wakeup from Suspend-To-Ram (S3, ACPI standard) in case a key on my external keyboard is pressed. It only wakes up if a key on the internal Laptop keyboard is pressed... from Suspend To Ram. It seems if I plug in a USB mouse, that the USB port isn't even powered. I have no BIOS option to change this. Further specific information regarding the device: usb-devices T: Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#= 13 Spd=1.5 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=04d9 ProdID=1603 Rev=03.10 S: Manufacturer= S: Product=USB Keyboard C: #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=01 Driver=usbhid I: If#= 1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid root@underwater-laptop:/# lsusb [...] Bus 001 Device 013: ID 04d9:1603 Holtek Semiconductor, Inc. Bus 001 Device 004: ID 0bda:0138 Realtek Semiconductor Corp. Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub [...] If this doesn't work I have to properly explain why :( - but I think it is very hard to research this kernel internal. Any hints for good information here? I hope it's possible... I'm just looking for any solution. edit: this, waking up on USB, works on Windows! Thanks a lot, Marius

  Read the article

• Get Ready for Anytime, Anywhere Engagement

  - by Christie Flanagan

  Normal 0 false false false EN-US X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} Are you ready for 2015?  According to IDC, 2015 is the year when more users are projected to access the internet using mobile devices than with PC’s or other wired devices.  It’s no doubt that mobile devices are a critical means of communication today, and are on track to become increasingly more important in the coming years. However, device formats are so varied that delivering a mobile web experience that will engage site visitors and enhance your brand can be a daunting task. Solutions that empower organizations to easily extend their web presence to the mobile channel, while saving significant time and effort in managing mobile sites, are now essential in our ever connected mobile world. So what are some of the things organizations should look for in such a solution? Mobile device form factors, networks, protocols, and browsers vary widely, and reformatting web content for thousands of different device and software combinations is a prohibitive task. An effective mobile solution can make this process seamless by automatically formatting designated web content for mobile delivery.  By automatically detecting a site visitor’s device configuration, the selected web content can be sized and formatted for optimal display on that particular device. This can save tremendous time involved in building, formatting, and maintaining individual websites or mobile applications for different mobile devices. It’s not enough to simply support the thousands of different mobile device types that are out there. It’s also critical to make it easy for marketers and other business users to manage mobile sites and mobile content. Those responsible for maintaining an organization’s web and mobile experiences need the ability to edit content using rich text editor tools and then preview that content directly in the context of the mobile website and the traditional website, ideally from the same business user interface. Powerful capabilities such as these make managing the web experience for mobile devices easy, even with frequently changing content, across a multitude of different devices. This saves tremendous time involved in building, formatting, and maintaining individual websites or mobile applications for different mobile devices. When content or business needs change, the business user needs only to change site content once, and it is seamlessly deployed to the web and all mobile channels.Geo-location is another critical input to making the online experience engaging and relevant for web visitors who are increasingly mobile. A mobile solution should enable use of device GPS data to deliver location-based content and services to mobile website visitors. Organizations can provide mobile site visitors with location-sensitive search results, location-based offers and recommendations, integration of maps and directions into site content, and much more – all critical for meeting the needs of those on the go.To hear more about how mobile is changing the game, check out our recent webcast with Ted Schadler, Vice President, Principal Analyst, Forrester, where he discussed why mobile is the new face of engagement, or learn more about how to extend your web presence to the mobile channel with Oracle WebCenter Sites and Oracle WebCenter Sites Mobility Server.

  Read the article

• Oracle ADF Mobile Video Series: End-to-End Mobile Application Development Experience

  - by Michelle Kimihira

  Today's video demonstrates how to create an ADF Mobile application and deploy to a device, all within 10 minutes! We will show you the key aspects of how to quickly and declaratively create an on-device mobile application and get it running on an actual device. Additional Information Product Information on OTN: ADF Mobile Product Information on Oracle.com: Oracle Fusion Middleware Follow us on Twitter and Facebook Subscribe to our regular Fusion Middleware Newsletter

  Read the article

• thick client migration to web based application

  - by user1151597

  This query is related to application design the technology that I should consider during migration. The Scenario: I have a C#.net Winform application which communicates with a device. One of the main feature of this application is monitoring cyclic data(rate 200ms) sent from the device to the application. The request to start the cyclic data is sent only once in the beginning and then the application starts receiving data from the device until it sends a stop request. Now this same application needs to be deployed over the web in a intranet. The application is composed of a business logic layer and a communication layer which communicates with the device through UDP ports. I am trying to look at a solution which will allow me to have a single instance of the application on the server so that the device thinks that it is connected as usual and then from the business logic layer I can manage the clients. I want to reuse the code of the business layer and the communication layer as much as possible. Please let me know if webserives/WCF/ etc what i should consider to design the migration. Thanks in advance.

  Read the article

• ext4 hogs lot of unkown space compared to ext3

  - by rejith

  Ext4 FS has claimed 3% of partition space. Where has this gone and can I get it reclaimed? I have tried disabling Journals for the ext4 partition. Even this is not helping. Any other tricks I can try to get the space reclaimed other than reverting back to ext3? $ lsb_release -cr Release: 12.04 Codename: precise df -hP |grep media /dev/sda3 21G 430M 20G 3% /media/MAIL /dev/sda2 148G 188M 148G 1% /media/DATA => if I move this to ext4 its claiming 2.4G /dev/sda3 on /media/MAIL type ext4 (rw,nosuid,nodev,uhelper=udisks) /dev/sda2 on /media/DATA type ext3 (rw,nosuid,nodev,uhelper=udisks) $ sudo tune2fs -l /dev/sda3 |grep 'Reserved block count' Reserved block count: 0 $ sudo tune2fs -l /dev/sda2 |grep 'Reserved block count' Reserved block count: 0 NO hidden files or directories $ sudo du -ah *;pwd 16K lost+found /media/MAIL

  Read the article

• File doesn't exist when trying to change permissions following the avasys image scan manual

  - by Howard Graham

  I was finally able to connect to avasys.jp and downloaded and installed iscan_2.28.1-3.ltdl7_amd64.deb iscan-data_1.13.0-1_all.deb. The programs appeared to install correctly. I then ran sane-find-scanner and got back: found USB scanner (vendor=0x04b8, product=0x012d) at libusb:001:003 I then ran lsusb and got back: Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 003: ID 04b8:012d Seiko Epson Corp. Perfection V10/V100 (GT-S600/F650) Bus 001 Device 004: ID 03f0:4817 Hewlett-Packard Bus 002 Device 002: ID 093a:2510 Pixart Imaging, Inc. Optical Mouse the avasys image scan manual instructed me to run chmod 0666 /proc/bus/usb/001/003 which returned chmod: cannot access `/proc/bus/usb/001/003': No such file or directory In 12.04, no such directory exists. 12.04 appears to deal with USB in another way. What must I do to get the usb port 001/003 recognized by xsane and sane as the port where the scanner can be located? What must I do to continue installing the scanner?

  Read the article

• Random Position between ranges.

  - by blakey87

  Does anyone have a good algorithm for generating a random y position for spawning a block, which takes into account a minimum and maximum height, allowing player to to jump on the block. Blocks will continually be spawned, so the player must always be able to jump onto the next block, bearing in mind the minimum position which would be the ground, and the maximum which would the players jump height bearing in mind the ceiling

  Read the article

• Flixel: doesn't light tile up

  - by Arno

  i'm creating a game with flixel, and I want to have a effect when you mouse over a tile, I tried implementing it, and this is what it gives: public class GameState extends FlxState { private var block:EmptyBlock; public function GameState() { } override public function create():void { for (var i:Number = 0; i < 30; i++) { block = new EmptyBlock(i, 20); block.create(); } } override public function update():void { block.update(); super.update(); } } } GameState class and here is the EmptyBlock class: public class EmptyBlock { private var x:int; private var y:int; private var row:FlxRect public function EmptyBlock(x:int, y:int ) { this.x = x; this.y = y; } public function create():void { row = new FlxRect(x, y, 32, 32); trace ("Created block at" + x + y); } public function update():void { if (FlxG.mouse.screenX == row.x) { if (FlxG.mouse.screenY == row.y) { var outline:FlxSprite = new FlxSprite(row.x, row.y).makeGraphic(row.width, row.height, 0x002525); } } } } }

  Read the article

• Threading models when talking to hardware devices

  - by Fuzz

  When writing an interface to hardware over a communication bus, communications timing can sometimes be critical to the operation of a device. As such, it is common for developers to spin up new threads to handle communications. It can also be a terrible idea to have a whole bunch of threads in your system, an in the case that you have multiple hardware devices you may have many many threads that are out of control of the main application. Certainly it can be common to have two threads per device, one for reading and one for writing. I am trying to determine the pros and cons of the two different models I can think of, and would love the help of the Programmers community. Each device instance gets handles it's own threads (or shares a thread for a communication device). A thread may exist for writing, and one for reading. Requested writes to a device from the API are buffered and worked on by the writer thread. The read thread exists in the case of blocking communications, and uses call backs to pass read data to the application. Timing of communications can be handled by the communications thread. Devices aren't given their own threads. Instead read and write requests are queued/buffered. The application then calls a "DoWork" function on the interface and allows all read and writes to take place and fire their callbacks. Timing is handled by the application, and the driver can request to be called at a given specific frequency. Pros for Item 1 include finer grain control of timing at the communication level at the expense of having control of whats going on at the higher level application level (which for a real time system, can be terrible). Pros for Item 2 include better control over the timing of the entire system for the application, at the expense of allowing each driver to handle it's own business. If anyone has experience with these scenarios, I'd love to hear some ideas on the approaches used.

  Read the article

• Ubuntu 12.04 LTS - Apple iPad 3 (iOS 7 non-jailbroken) USB connection problem

  - by Eldian

  I've bought an Apple iPad 3 (iOS 7 non-jailbroken), and I'm trying to connect it to my PC running Ubuntu 12.04 through the original USB cable. After I plugged in the cable, I got this message on the PC: The device 'iPad' is locked. Enter the passcode on the device and click 'Try again'. Slide to unlock on iPad, it's OK, I got this message on the PC again: The device 'iPad' is locked. Enter the passcode on the device and click 'Try again'. iPad: Trust this computer? TRUST/DON'T TRUST I've selected TRUST. PC: Unable to mount - DBus error org.freedesktop.DBus.Error.NoReply: Message did not receive a reply (timeout by message bus) OK, I've read some forums, everywhere there was this solution: "Install: ifuse, libimobiledevice-utils, Rhythmbox OK, I've installed them through terminal, and used the idevicepair unpair && idevicepair pair command also in the terminal. Then I got this message: Device is not paired with this host. I don't know what to do. Please help!

  Read the article

• How do you run XBMC on nvidia dual screen and stop it from taking over the keyboard and mouse?

  - by Paul Swartout

  I have set up dual screen under Ubuntu 12.04. I have a GeForce 8500 GT and have used the nVidia control panel to set up dual screen in "Separate screen mode". Here's the resulting xorg.conf # nvidia-settings: X configuration file generated by nvidia-settings # nvidia-settings: version 295.33 (buildd@zirconium) Fri Mar 30 13:38:49 UTC 2012 Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" 0 0 Screen 1 "Screen1" RightOf "Screen0" InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" Option "Xinerama" "0" EndSection Section "Files" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor0" VendorName "Unknown" ModelName "Maxdata/Belinea B1925S1W" HorizSync 31.0 - 83.0 VertRefresh 56.0 - 75.0 Option "DPMS" EndSection Section "Monitor" # HorizSync source: builtin, VertRefresh source: builtin Identifier "Monitor1" VendorName "Unknown" ModelName "CRT-1" HorizSync 28.0 - 55.0 VertRefresh 43.0 - 72.0 Option "DPMS" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce 8500 GT" BusID "PCI:1:0:0" Screen 0 EndSection Section "Device" Identifier "Device1" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "GeForce 8500 GT" BusID "PCI:1:0:0" Screen 1 EndSection Section "Screen" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "TwinView" "0" Option "metamodes" "CRT-0: nvidia-auto-select +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" # Removed Option "metamodes" "CRT-1: 1280x768 +0+0" Identifier "Screen1" Device "Device1" Monitor "Monitor1" DefaultDepth 24 Option "TwinView" "0" Option "metamodes" "CRT-1: 1360x768_60 +0+0" SubSection "Display" Depth 24 EndSubSection EndSection All well and good and I have a nice blank XWindow displayed on my TV (the 2nd monitor). I then fire up XBMC from a terminal on the PC monitor using DISPLAY=:0.1 xbmc XBMC fires up quite nicely on the TV however I can no longer use the main PC monitor / mouse / keyboard as XBMC on the TV screen seems to have focus. I was hoping to have XBMC running on the TV and let the kids use the MCE remote whilst I get on with my work on the PC monitor. Does anyone have any idea how to overcome this? I'm presuming there's some xorg.conf fun and games needed but I've no idea where to start to be honest.

  Read the article

• Sonicwall site-to-site can not access remote network

  - by vpnwizard

  I have 2 SonicWall devices (tz100) in 2 different geographical locations. They are connected to each other using site-to-site vpn connection and this works just great. Device A network - 192.168.1.0/24 Device B network - 192.168.2.0/24 When I connect to one device, I can access, from my computer, anything on that specific subnet. However, I am unable to view anything, from my computer, on the other network. Is there a setting somewhere that will forward my requests to the other subnet? Example - I VPN into Device A, but would like to get to a server which is on the Device B network (192.168.2.0/24)

  Read the article

• Rendering transparent textures in directX

  - by Vibhore Tanwer

  I am working with a directX application with WPF, I am facing a problem with videos and images that contains transparent pixels, I have to draw a color in background an then a video/image over it. What I expect is background color should be visible while playing video only non transparent pixels should be visible but what I get is a black background behind the video. I am using following settings on device to achieve alpha blending : device.RenderState.SourceBlend = Blend.SourceAlpha; device.RenderState.DestinationBlend = Blend.InvSourceAlpha; device.RenderState.AlphaBlendEnable = true; What am I missing here? What is the best approach to handle transparent videos? Any help will be of great value to me.

  Read the article

• How to disable integrated webcam and still be able to use an external one

  - by alikasundara

  I am looking for a way to disable the webcam that is integrated into my laptop. The webcam is using uvcvideo module but I do not want to blacklist it since it is also being used by an external webcam I have. Is there any way of disabling the device itself without touching the modules list? This is how the webcams are listed by lsusb. The first one is an integrated one (It is identified by some apps as BisonCam NB Pro), the second one is the external Logitech C525: Bus 002 Device 004: ID 5986:0361 Acer, Inc Bus 003 Device 002: ID 046d:0826 Logitech, Inc. I have already checked BIOS - there is no way of disabling the webcam from there. Besides I would love to learn how to disable the device by ID anyway. Thanks!

  Read the article

< Previous Page | 119 120 121 122 123 124 125 126 127 128 129 130  | Next Page >